TECHNICAL DOCUMENTATION

SSP 189 The 2.3 l petrol engine in the LT 1997

PDFEN52 pages927 KB
SSP 189 The 2.3 l petrol engine in the LT 1997 - PDF cover

This PDF is currently unavailable.

Read document text
Service189The 2.3 l petrol engine in the LT ‘97Design and FunctionSelf Study ProgrammeCustomer Service A commercial vehicle with a petrol engine?...is not impossible. Volkswagen Commercial Vehicles is featuring a 2.3 l petrol engine in its LT '97 range as a high performance option. Find out more about it in this self study programme!2 Page Overview ........................................................................................ 4 Engine - mechanical ...................................................................... 6 Oil circuit ........................................................................................ 8 Cooling system .............................................................................. 10 Fuel supply ..................................................................................... 11 Self check ....................................................................................... 13 Injection and ignition system....................................................... 14 System overview........................................................................... 16 Ignition system .............................................................................. 18 Injection system ............................................................................ 28 Idling control.................................................................................. 32 Exhaust cleaning ........................................................................... 35 Functional diagram ....................................................................... 38 Self diagnosis................................................................................. 41 Self check ....................................................................................... 45NewNote!The Self Study Programme is not a repair manual!For information on testing, adjustments and repairs refer to the appropriate customer service literature.3 OverviewThe new 2.3 l petrol enginehas been specially developed for commercial vehicles. It delivers high level torque over a wide range of revs.189-01The engine has a cross flow cylinder head with four valve technology. This makes for good fuel mixing and therefore low emission combustion.189-614 The torque and performance diagram shows a maximum torque value of 210 Nm. The torque value is over 180 Nm in an engine speed range of 1500 to 5500 1/min. The engine delivers its maximum output of 105 KW at 5500 1/min. This permits constant and strong tractive power even with heavy loads. Throughout the entire engine speed range it is possible to drive economically yet with powerful acceleration and few gear changes.110 100 90 80 70 60 50105KW210Nm 40 30 20 10 0 0220 200 180 160 140 120 1001000 2000 3000 4000 5000 6000 7000189-76Data Engine abbreviation Cylinders Capacity Bore Stroke Compression Power Maximum torque Engine management AGL R4 2295 cm3 90.9 mm 88.4 mm 8.8 : 1 105 kW/ 143 HP at 5500 1/min 210 Nm at 4000 1/min Siemens Motronic5 Engine - mechanicalEngineThe cylinder crank case is made of cast iron.The top section gets very hot from the combustion. Coolant flows through the cooling slit, dissipating the heat.Cooling slit189-714-valve technologyEach cylinder has two inlet valves and two outlet valves.The 4 valves are operated by two overhead cam shafts via hydraulic bucket tappets.The benefits of the 4-valve technology are high traction power and good power delivery even at low and medium revs, high level cylinder filling low fuel consumption fewer harmful substances in exhaust.189-51Outlet sideInlet side6 Controlinlet cam shaft outlet cam shaft timing chainchain tensioner crank shaft189-56oil pump189-55The cam shafts are driven by the crank shaft and a chain. A second chain drives the oil pump.Chain tensioner A chain tensioner tensions the timing chain. It functions by oil pressure. A locking segment ensures that the timing remains tensioned even of there is no oil pressure.It is only possible to reset the locking segment when the chain tensioner has been taken out.7 Oil circuitSchematic diagram of oil circuitChain tensionerOil filter Pressure limiting valve Return stop Oil pressure switch Oil pumpReturn valve189-59The oil pump is a sickle pump. It pumps the oil out of the oil sump through the oil filter to the cam shafts to the cylinder head and to the chain tensioner.For the piston cooling there are holes in the connecting rod eye through which the oil is pumped to the base of the piston via the crank shaft bearing. A return valve and the return stop prevent the oil from running back out of the engine. If the oil filter is blocked the pressure limit valve opens the by-pass line.There is an excess pressure valve.The oil pressure switch is white. Its function range is between 0.2 and 0.5 bar.8 Crank case ventingthrottle valvesbreather line189-74There is a breather line between the crank case and the intake manifold. The gases flow from the crank case through the breather line and the throttle valves into the intake manifold.When idling and under part load fresh air flows through the crank case venting system into the crank case. The fresh air mixes with the gases in the crank case. This prevents sludging of the engine oil.9 Cooling systemSchematic diagram of cooling circuitexpansion tankcoolertemperature controllercoolant pumpheating system heat exchanger189-58Minor circuit The coolant pump circulates the cold coolant around the engine block and, if required, around the heating system/heat exchanger.Major circuit The temperature controller regulates the engine temperature. Once the engine has reached its operating temperature a thermostat valve opens and the coolant pump pumps the hot coolant out of the engine into the cooler. There it is cooled and flows back to the coolant pump. The expansion tank compensates the expansion of the coolant at high temperatures.10 Fuel supplySchematic diagram of fuel systemdiaphragm pressure controllerheader fuel filterfuel pumpfuel tank189-57The fuel pumppumps up the fuel, pushing it through the fuel filter and the diaphragm pressure controller to the injection valves.The diaphragm pressure controllercontrols the fuel pressure in the header, dependent on the intake manifold pressure. It channels excess fuel back into the fuel tank.11 Fuel supplyActive carbon filter systemthrottle valve control unitvalve for tank ventingbreather linereturn valveactive carbon container189-73The active carbon filter system consists of an active carbon container air supply and exhaust lines between tank and active carbon container return valve which opens the line in the opposite direction, depending on pressure a breather line from the active carbon container to the exterior a line for fuel vapours between the active carbon container and the throttle valve control unit and a valve which is controlled by the engine control unit when fuel vapours are to be fed to the mixture .The active carbon system prevents fuel vapours escaping into the environment. This is achieved by: • • • creation of slight excess pressure in the fuel tank when engine switched off pressure equalisation with engine running return of fuel vapours into combustion process-12 Self check1.What is the oil for which is pumped through the holes in the connecting rod eye to the base of the piston?2.Complete the following text!The ____________________________ sucks up the fuel, pumps it via the ____________________________ through the ____________________________ to the injection valves. The ____________________________ controls the fuel pressure in the header depending on the ____________________________ and channels excess fuel back to the ____________________________ .13 Injection and ignition systemSiemens MotronicIgnition systemResponsible for: • calculating the advance angle • adjusting the advance angle • monitoring the ignition coils • multiple ignitionInjection systemResponsible for: • calculating the injection time • determining the injection sequence • calculating the mixture enrichmentIdling controlResponsible for: • ensuring smooth engine running under all loads • maintaining idling speeds under all loads • additionally: to heat the catalytic converter after ignition14 Engine speed sender G28Plug to vehicleF MPlug to engineFMIgnition map balancing resistor N221Pressure tube to sender for intake manifold pressure sender G71189-07Plugs M and F have the same construction. Check the labels on the plugs and on the control unit.Ignition map balancing resistor If using ROZ 91 instead of ROZ 95 the fixed resistor in the control unit needs to be removed. The ignition map balancing resistor shifts the ignition point to "delayed".189-0815 System overviewEngine speed sender G28 Control unit for Motronic J220 Sender for coolant temperature G62In control unit for Motronic J220: Intake manifold pressure sender G71Intake air temperature sender G42Lambda probe G39In the Throttle valve control unit J338: Throttle valve potentiometer G69 Throttle valve positioner potentiometer G88 Idling switch F60Self diagnosis connectionIgnition map balancing resistor N22116 Fuel pump relay J17Injection valves N30, N31, N32, N33Cylinder transformers N222, N223In throttle valve control unit J338: Throttle valve positioner V60Valve for tank venting N80Exhaust flap valve N220189-0417 Ignition systemThe functions of the ignition system are: to calculate the advance angle to adapt the advance angle to monitor the ignition coils multiple ignitionIntake manifold pressure sender G71Injection valves N30, N31, N32, N33Engine speed sender G28Intake air temperature sender G42Sender for coolant temperature G62 Cylinder transformers N222, N223189-77The static load high tension distribution system consists of: the control unit for processing the input signals two ignition coils each of which are allocated two spark plugs.J22018189-22 During ignition the engine control unit interrupts the power supply to the appropriate ignition coil. The sudden drop in voltage on the primary coil induces a high voltage in the secondary circuit. The discharge creates the ignition sparks. The secondary ignition coil, the spark plugs and the engine earth form a closed circuit.189-23Double spark ignition During each ignition cycle there is a spark on both of the connected spark plugs. One is triggered in the power stroke and one in the exhaust stroke.1234189-70 189,70Electrical switching1510 11 P QInput signal ignition transformer N222 Input signal ignition transformer N223 Spark plug plug Spark plugs1 N223J22011 15 1 10 15 N222 (T17a)P Q 31189-2419 Ignition systemMonitoring the ignition coilsIf faults arise in the ignition system the catalytic converter can be damaged through overheating. To protect the converter the ignition coils are monitored. If an ignition coil does not spark, the injection in the appropriate cylinder is cut.189-37Multiple sparkingWhen the engine is started a series of sparks is emitted instead of just one. This makes it easier for the engine to start. Multiple sparking only takes places when the engine temperature is below 20°C.10o189-3820 Advance angle adjustmentWarming up phase After starting the engine the engine control unit adjusts the advance angle for roughly 25 seconds to "delayed". The combustion temperature increases and the catalytic converter heats up more quickly.:25OT189-32Digital Idling Stabilisation DIS The DIS supports the idling control by adjusting the throttle flap. The idling speed is controlled by the control unit adjusting the advance angle up to 8° before or after TDC.OT 8 8189-33Overrun cut-off When moving from overrun to acceleration there is jolt caused by the change in the torque. To make this transition as gentle as possible the control unit sets the advance angle to "delayed" for two seconds.:02OT189-34Prevention of engine knock At higher air intake and coolant temperatures there is a tendency for engine knock to arise. For this reason the control unit sets the advance angle to "delayed" in this situation.OT189-35Load change When travelling uphill there is a slight tendency to jolting. After a load shift with traction the control unit adjusts the advance angle to "Delayed" for two seconds.:02OT5189-3621 Ignition systemThe engine speed sender G28 is an inductive sender. It registers the position of the crank shaft and the engine speed.189-18Segments are attached to the flywheel for the sender to recognise. When the segments pass over the sender this changes the magnetic field. The engine control unit calculates the engine speed from this information. There is also a permanent magnet on one of the segments. The control unit recognises the signal from the segments with and without the permanent magnet. It assigns the segment with the magnet cylinders 2 and 3. In this way cylinders 1 and 4 can be distinguished from cylinders 2 and 3.189-6722 Application of signal :The engine speed signal is needed to calculate advance angle injection and engine load.Consequences of signal failure:The engine cuts out. The engine cannot be started."Error message" self diagnosis: Engine speed sender G28 no signal/implausible signal no magnet speed implausibleElectrical switching: 1, 2 input signal - engine speed sender G28G281 (T2) J2202189-1923 Ignition systemThe coolant temperature sender G62 registers the temperature of the coolant and relays the signal to the engine control unit. The sensor is an NTC resistor.189-13Application of signal:-recognition of engine temperature calculation of advance angle calculation of injection timeConsequence of signal failure:The control unit creates substitute values. These are so close to the actual value that the error cannot be registered in the measured data block. The error will, however, be displayed in the error memory."Error message" self diagnosis: Coolant temperature sender G62 short circuit interruption implausible signal loose contactElectrical switching: 7 9 input signal - coolant temperature sender G62 output signalG62(T17a)79 J220189-1524 The intake air temperature sender G42 registers the temperature of the intake air and relays the signal to the engine control unit. The sensor is an NTC resistor.189-16Application of signal:-calculation of advance angle calculation of engine loadConsequence of signal failure:The control unit creates substitute values. These are so close to the actual value that the error cannot be registered in the measured data block. The error will, however, be displayed in the error memory."Error message" self diagnosis: Intake air temperature sender G42 short circuit interruption loose contactElectrical switching: 16 9 input signal - intake air temperature sender G42 output signalG42(T17a) 169 J220189-1725 Ignition systemThe intake manifold pressure sender G71 is in the Motronic control unit. A pressure tube connects the manifold with the intake manifold pressure sender. The sensor is a piezoelectric resistor. It changes its resistance depending on the pressure.Application of signal:-calculation of engine loadConsequence of signal failure:If the manifold pressure sender malfunctions a substitute value is calculated from the signals from the engine speed and throttle flap potentiometer sender signals."Error message" self diagnosis: Intake air temperature sender G71 implausible signal no signal26 Notes27 Injection systemThe functions of the injection system: to calculate the injection time to determine the injection sequence to calculate the mixture enrichmentEngine speed sender G28Intake manifold pressure sender G71 Injection valves N30, N31, N32, N33Sender for coolant temperature G62Intake air temperature sender G42189-78Function The control unit calculates the required fuel quantity and the appropriate injection time from the input signals. It controls two injection valves simultaneously.28 Injection valves N30 - N33 inject the fuel in a fine mist into the intake channels. The fuel emerges from two holes and is injected to the inlet valves. The injection valves have no resistors in their circuit. They have 12 V clocked control voltage. A continuous 12 V supply would destroy them.189-69189-68The injection valves should not be exposed to a continuous 12 V supply.29 Injection systemMixture enrichmentStart/warm-up A cold engine needs a rich mixture. This is why the control unit increases the injection quantity for a cold start and during the warmup phase.189-40Acceleration During acceleration the control unit enriches the mixture to increase the performance. This may involve multiple injections.189-41Full load In order to increase the power optimally at full load the control unit increases the proportion of fuel in the mixture. The injection valves remain open longer.189-4230 Injection valve cut-offOverrun cut-off During overrun no fuel is injected. In overrun the braking action of the engine is increased less fuel is used the level of harmful emissions in the exhaust is reduced.189-43Engine speed limit The engine speed is limited to 6200 1/min. If the maximum speed is exceeded no more fuel is injected.62 00189-4431 Idling controlThe idling control has two functions: to ensure smooth engine running for all engine loads to maintain the idling revs for all engine loads additional function: to warm up the catalytic converter at start upEngine speed sender G28In throttle valve control unit J338: - Idling switch F60 - Throttle valve potentiometer G69 - Throttle valve positioner potentiometer G88In throttle valve control unit J338: - Throttle valve positioner V60Intake air temperature sender G42189-79The idling control is supported by the advance angle adjustment. This reacts more quickly than the throttle valve adjustment.32 The throttle valve control unit J338Throttle valve positioner V60Electrical supplyThrottle valve potentiometer G69 Throttle valve positioner potentiometer G88Idling switch F60189-27Construction:The throttle valve control unit has the same construction as the throttle valve control unit described in SSP 173. The only difference is that the idling switch is on the exterior and on the opposite side.Signal processing:The throttle valve control unit recognises the position of the throttle valve positioner and changes it until the desired idling speed has been reached. In this way the idling speed can be set for different engine loads.33 Idling controlAdditional function: warming up the catalytic converter The catalytic converter should be heated up as quickly as possible to operating temperature. Therefore when the engine is cold the control unit raises the idling speed for 25 seconds after start up to 1150 1/min.:2511 50189-46Consequences of signal failure in throttle valve control unit:An emergency speed is mechanically set by means of a spring"Error message" self diagnosis: Idling switch F60 implausible - closed loose contact implausible - openThrottle valve potentiometer G69 signal too large signal too small loose contactThrottle valve positioner - potentiometer G88 signal too large signal too small loose contact Electrical switching:J2205, 14 control for throttle valve positioner V60 17 input signal idling switch F60 8 input signal throttle valve positioner potentiometer G88 6 output signal of potentiometer 15 input signal throttle valve potentiometer 9 sender earth(T17a) 5141786159F60 M G88 V60 G693134189-28 Exhaust gas cleaningThe 3-way catalytic converterreduces the level of harmful substances carbon monoxide (CO) hydrocarbon (HC) nitrogen oxide (NOx)in the exhaust gas. It is contained in a stainless steel housing.189-49Operating temperature: The catalytic converter cuts in at a temperature of roughly 250°C. The ideal operating temperature is between 400° and 800°C. These temperatures ensure high level reduction of harmful emissions long life.At temperature above 1400°C the ceramic core melts. This would destroy the catalytic converter.35 Exhaust gas cleaningThe exhaust flapFunction: The exhaust flap, when closed, channels the stream of exhaust gases directly to the catalytic converter so that it can reach its operating temperature. This happens at start up, during idling and part load. When the flap is closed the stream of hot exhaust gases is channelled directly from the engine to the catalytic converter. When the flap is open the exhaust gas is channelled to the catalytic converter via the silencer. The gases cool down slightly in the silencer, yet are still within the operating temperature of the catalytic converter.Function: The engine control unit operates the exhaust flap via the exhaust flap valve and the pressure container. Schematic diagram of exhaust flap controlvacuum line exhaust streamsilencerpressure container valve for exhaust flap N220exhaust flapcatalytic converter189-50Consequence of signal failure: The flap is open, the catalytic converter cannot overheat.If problems arise the exhaust flap should be given a visual check. See repair manual.36 Lambda control This supports the function of the catalytic converter by altering the quantity of fuel injected depending on the oxygen content of the exhaust. This is to ensure that the exhaust can be cleaned optimally in the catalytic converter. Conditions for lambda control: • • • coolant temperature 60°C idling of part load no overrun cut-offLambda probe G39 This measures the oxygen content of the exhaust thereby making lambda control possible. This value is then passed to the control unit as a voltage signal. The lambda control is not possible until an operating temperature of 300°C has been reached. To aid this, electric heating is integrated in the probe. The optimum temperature is around 600°C. The reaction times for the lambda probe are shortest at this temperature.Electric circuit: 6, 7 Lambda probe G39 input signal 16 Control of lambda probe heating 3 Control of exhaust flap N220J2206 7 16 (T17b) 3Z19N220G39 31189-7537 Functional plan30 15N30N33N31N32G42G62X2 4 13 (T17a) 16 7 9 J22 11 10 (T17a) 5 14 17 8 6 15X1 N223 4b 2 P Q IN OUT 4a 3 4b 4 4a 1 15 1 15 N222 M G88 V60 G69 F6038 30 15A G28BCN221S811 (T2)210151314(T17)1 5 96716(T17)1738J17 Z19 N80 N220M G39G631189-6039 F60 G6 G39 G42 G62 G69 G88 G28 J17 J220 J338 N30 N31 N32 N33 N80idling switch fuel pump lambda probe intake air temperature sender coolant temperature sender throttle valve potentiometer throttle valve positioner potentiometer engine speed sender fuel pump relay Motronic control unit throttle valve control unit injection valve cylinder 1 injection valve cylinder 2 injection valve cylinder 3 injection valve cylinder 4 valve for ACF input signal output signal supply voltage earth connectionN220 valve for exhaust flap N221 resistor for ignition map balancing resistor N222 ignition transformer for cylinders 1 and 4 N223 ignition transformer for cylinders 2 and 3 P Q V60 Z19 A B C spark plug plug spark plugs throttle valve positioner heating for lambda probe self diagnosis engine speed signal input signal road speed40 Self diagnosisThe self diagnosis systemmonitors the sensor signals the control of the actuators and the control unit.If the control unit detects an error it calculates a substitute valve from other signals and provides emergency operation functions. Every detected error is stored in the control unit.V.A.G 15511 4 7 C2 5 8 03 6 9 QIf the control unit detects an error it calculates a substitute valve from other signals and provides emergency operation functions. Every detected error is stored in the control unit.V.A.G 1551/5The following functions are available: 01 - control unit version inquiry 02 - error memory inquiry 04 - basic setting 05 - delete error memory 07 - actuator diagnosis189-6308 - read measured data block42 Function 02 - Error memory inquiryThe colour coded sensors and actuators are monitored by the self diagnosis.189-64The self diagnosis system distinguishes between the following errors: errors which are constantly present errors which are present for longer than 3 seconds loose contact errors which arise more than 5 times during a journey.If an error does not occur for 19 journeys it is then deleted. If the engine control unit is removed or the battery is disconnected the error messages are lost.43 Self diagnosisFunction 04 - Basic setting The control unit activates the throttle valve control unit. It registers the increase in the current of the servo-motor and the resistance value of the throttle valve positioner potentiometer. It stores these values. There are two possible ways to activate the basic setting: - turn on the ignition and wait for 10 seconds or - select function 04 on the V.A.G. 1551 and proceed following the instructions.In both cases the accelerator pedal must not be depressed.Function 07 - actuator diagnosis- tank venting valve N80 - exhaust flap N220 and - the exhaust flap after start up are activated.44 Function 08 - read the data tableFunction 08 - read the data table.189-6645 Self check1. To run the engine on ROZ 91 ... A ... the start of the injection phase needs to be adjusted. ... nothing needs to be done. ... the ignition map balancing resistor in the control unit needs to be removed.B C2. Draw in the link between the spark plugs and the ignition coils.N222N22312343. Which of the following statements are correct? Tick the right answers.AIf an ignition coil develops a fault the injection is cut on the appropriate injection valves. The control unit measures the current flowing between the ignition coil and the spark plugs in order to monitor the secondary circuit. The current and voltage are monitored in the circuit between the control unit and the spark plugs.BC46 4. Decide which statements belong together. Connect them up.After starting the ignitionthe injection quantity is increased.When moving from overrun to accelerationthe advance angle is set to " Delayed" for roughly 25 seconds.On starting from coldthe quantity of fuel in the mixture is increased.When the engine is coldthe advance is briefly set to "delayed".With full loadthe fuel supply is cut by the injection valves being switched off.In overrunthe idling revs are increased for 25 seconds after start up to 1150 1/min.5.Complete the following text.Segments are mounted on the ____________________________ which are detected by the ____________________________. A ____________________________ is attached to each segment. The ____________________________uses this to distinguish whether the signal belongs to ___________________ and ______ or to ___________________ and ______ .47 Self check6. An error in the coolant temperature sender can... A B C ...be found by reading the error memory. ...not be found while it is still installed. ...be found by checking the values in the data list.7. Give two factors which protect or support the function of the catalytic converter:8.Complete the following text.The engine control unit activates the flap via the ____________________________ and the ____________________________ . When the flap is ____________________________ the hot stream of exhaust gas is channelled directly from the engine to the catalytic converter and accelerates the heating up of the converter to its working temperature of roughly 400°C. When the flap is ____________________________ the exhaust stream is channelled to the catalytic converter via the silencer. In this case the gas is so hot that even after being cooled in the ____________________________ it is still hot enough for the working temperature of the catalytic converter to be reached.48 Notes49 Answers to self check questions on page 13: 1.: for cooling2.: The fuel pump sucks up the fuel, pumps itvia the fuel filter through the header to the injection valves. The diaphragm pressure controller controls the fuel pressure in the header depending on the intake manifold pressure and channels excess fuel back to the fuel tank.Answers to self check questions from page 43: 1.: c 2.:N222N22312343.: a, c50 4.:after starting the ignition the injection quantity is increased.when moving from overrun to accelerationthe advance angle is set to "Delayed" for roughly 25 seconds.on starting from coldthe quantity of fuel in the mixture is increased.when the engine is coldthe advance is briefly set to "delayed".with full loadthe fuel supply is cut by the injection valves being switched off.in overrunthe fuel supply is cut by the injection valves being switched off.Please note that other combinations may also be correct.5.: Segments are mounted on the flywheel which are detected by the engine speed sender. A permanent magnet is attached to each segment. The control unit uses this to distinguish whether the signal belongs to cylinders 1 and 4 or to cylinders 2 and 3.8.: The engine control unit activates the flap via the exhaust flap valve and the pressure container.When the flap is closed the hot stream of exhaust gas is channelled directly from the engine to the catalytic converter and accelerates the heating up of the converter to its working temperature of roughly 400°C. When the flap is open the exhaust stream is channelled to the catalytic converter via the silencer. In this case the gas is so hot that even after being cooled in the silencer it is still hot enough for the working temperature of the catalytic converter to be reached.6.: a 7.: e.g. - exhaust flap control - heating the catalytic converter after start up51 Only for internal use. © VOLKSWAGEN AG, Wolfsburg All rights reserved 640.2810.08.20 Published: 05/96❀ This paper has been made from paper which has not been bleached using chlorine.