TECHNICAL DOCUMENTATION

SSP 190 Adjustable Turbocharger

PDFEN32 pages1 MB
SSP 190 Adjustable Turbocharger - PDF cover

This PDF is currently unavailable.

Read document text
Service.190Adjustable TurbochargerDesign and FunctionSelf-Study ProgrammeService Department If the water level in the mill stream drops, the current will no longer be sufficient to turn the water wheel. If the miller still wants to grind corn, then he has to narrow the stream of water.To the miller, the stream is as important as the exhaust gas energy is to the turbocharger. By using adjustable vanes, the response of the adjustable turbocharger at low engine speeds is quick.SSP 190/012 PageFundamental principles Design and function Mechanics Function chart System overview Engine control unit Sensors Actuators Self-diagnosis Functional diagram04 06 11 16 18 19 20 24 26 29Important! / Note!New!The Self Study Programme is not a Workshop Manual! Please refer to the Service Literature which contains all the relevant inspection, adjustment and repair instructions.3 Fundamental principlesThe basic principle of an exhaust gas turbochargerAn exhaust gas turbocharger is used to achieve high torques, and thus higher engine outputs. This effect is achieved by compressing the intake air. The higher intake air density allows a larger volume of air, and therefore more oxygen, to enter the combustion chamber during each intake cycle. The larger oxygen supply boosts the efficiency of the combustion process.The exhaust gas of an engine contains both thermal and kinetic energy. These energies are utilised to drive the exhaust gas turbine of the turbocharger. The exhaust gas loses some of its energy and cools down as a result. The exhaust gas turbine drives the compressor which in turn compresses the intake air, heating it up and thus reducing its density. The intake air is cooled down again in the air intercooler, thereby increasing its density.Air intercooler Heat The exhaust gas from the engine drives the exhaust gas turbine. The compressed and heated air is fed into the air intercooler.Air inletExhaust pipeSSP 190/02Compressor The compressor compresses the intake air.4Exhaust gas turbine The exhaust gas turbine drives the compressor. The exhaust gas turbocharger fitted with a by-passA turbocharger has two sets of problems: l The turbine speed at the top end of the speed range is high and the air is compressed more than is necessary. l At the bottom end of the speed range, the exhaust gas turbine does not reach the required speed. The air is not compressed sufficiently and the engine is unable to deliver the desired power output (turbo lag).It was decided to make a compromise regarding the design of the exhaust gas turbocharger fitted with a by-pass. At the top end of the speed range, a partial exhaust gas flow bypasses the turbocharger, thus ensuring that the optimum air compression ratio is not exceeded and that the engine delivers its full power output. However, this system is ineffectual at the lower end of the speed range. The by-pass is opened or closed by means of a pressure box.Turbocharger with by-passIntake airExhaust gas flowBypass Air intercooler pressure box Atmosphere Intake manifold Exhaust manifoldSSP 190/03 5 Design and functionThe designThe turbocharger in the exhaust gas turbine uses adjustable vanes instead of the by-pass. The adjustable vanes control the exhaust gas flow acting on the turbine wheel. The adjusting vanes are moved by means of a low-pressure box.Adjustable vanesExhaust gas turbine housingExhaust gas turbine wheelLow-pressure box for vane adjustmentSSP 190/046 Advantages - High engine output is available at the bottom end of the speed range since the exhaust gas flow is regulated by the adjustable vanes. - The lower exhaust gas backpressure in the turbine reduces fuel consumption at the top end of the speed range and also improves bottom-end power output. - Exhaust gas emissions decrease because an optimum charge pressure, and therefore also improved combustion, is attained across the full speed range.CompressorLubricating oil inletSSP 190/057 Design and functionThe designThe adjustable turbocharger, in contrast to the exhaust gas turbocharger fitted with a by-pass, produces the necessary compression not only at the top end of the speed range but also across the full speed range. This is made possible by feeding the exhaust gas flow into the turbine wheel via adjustable vanes.Turbocharger with adjustable vanesIntake airExhaust gas flow Vane Low-pressure boxAir intercooler Vacuum Atmospheric pressureCylinder headSSP 190/068 A gas must flow through a narrowed pipe more quickly than through a pipe without a restriction, provided that the pressure in the two pipes is equal. This fundamental physical principle is applied to the constant-output exhaust gas turbocharger.SSP 190/07Low engine speed and high charge pressure are required The cross-section of the exhaust gas flow is narrowed upstream of the turbine wheel by means of vanes. Since the exhaust gas is forced to pass through the restricted cross-section more quickly, the turbine wheel rotates faster. The high turbine speed at low engine speed generates the required charge pressure. The exhaust gas backpressure is high.VaneTurbine wheelCharge pressureExhaust gas pressureSSP 190/08Charge pressure Exhaust gas pressureHigh engine speed The turbocharger cross-section is adapted to the exhaust gas flow. In contrast to the by-pass, the entire exhaust gas flow can be fed through the turbine in this way. The vanes free a larger inlet cross-section, thereby ensuring that the required charge pressure is not exceeded. The exhaust gas backpressure drops.SSP 190/099 Test your knowledge1.Label the components shown in the illustration below.A CBD ESSP 190/052.Complete the following sentence: The of the exhaust gas turbine is narrowed or released ahead of the turbine wheel by means of.10 MechanicsAdjusting the vanesLow-pressure boxAdjusting ring Pilot Support ring ShaftVanesControl linkageSSP 190/10Guide pins of control linkageFit the vanes together with their shafts onto a supporting ring. There is a guide pin which engages in an adjusting ring at the back of the supporting ring of the vane shafts. All vanes can thus be rotated at the same rate and simultaneously via the adjusting ring.The adjusting ring is moved by the low-pressure box by means of the guide pin of the control linkage.11 MechanicsShallow vane angle = Narrow inlet cross-section of exhaust gas flowSteep vane angle = Large inlet cross-section of exhaust gas flow Direction of rotation of adjusting ringSSP 190/11SSP 190/12SSP 190/08SSP 190/09To allow a quick build-up of charge pressure at low speed and under full load, the vanes are set to a narrow inlet cross-section. The effect of the restriction is to speed up the exhaust gas flow, thus increasing turbine speed.The vanes are set at a steeper angle with increasing exhaust gas flow rate or if a lower charge pressure is required. The inlet cross-section is enlarged. As a result, the charge pressure and the turbine output remain virtually constant. The maximum angle of the vanes, and therefore also the largest possible inlet crosssection, is simultaneously the vane angle used in emergency operation.12 The N 75 solenoid valve and the low-pressure box for vane adjustmentVacuum control for flat vane angle adjustment The engine control unit controls the N 75 solenoid valve for vacuum supply. The maximum vacuum can, as a result, act on the low-pressure box. The vanes are adjusted at a shallow angle. This vane position allows the fastest possible maximum charge pressure build-up.Solenoid valve N75 Low-pressure boxShallow vane angleEngine control unitSSP 190/13Vacuum control for steep vane angle adjustment The solenoid valve is currentless. Atmospheric pressure is fed into the lowpressure box. The vanes are adjusted at a steep angle. This position is also the adjustment used in emergency operation.Solenoid valve N75 Low-pressure boxSteep vane angle adjustment Engine control unitSSP 190/14 13 MechanicsSolenoid valve N 75 and the low-pressure box for vane adjustmentVacuum control for intermediate stages of vane adjustment More or less power must be available to the engine to cater for momentary driving conditions. Therefore, the turbocharger must deliver the optimum charge pressure. The solenoid valve is driven in such a way that the vacuum level is adjusted to between atmospheric pressure and the maximum possible vacuum. This vacuum corresponds to the optimum vane angle adjustment for these speed and load ranges. The engine control unit can thus respond immediately to changing driving conditions in a continuous control process. It continuously adapts the vane angle adjustment to the desired charge pressure.solenoid valve N75 Intermediate stage of vane angle adjustmentLow-pressure boxEngine control unitSSP 190/1514 Test your knowledge1. A B C DWhat effects does the adjustable turbocharger have? High bottom-end torque. Lower fuel consumption at the top end of the speed range. A low charge pressure at low speeds Higher exhaust gas backpressures at high speeds2.Draw the position of the diaphragm in the low-pressure boxes.ABCSSP 190/1915 Function chartEngine control unit with integrated altitude sender and intake manifold pressure senderAir mass meterSolenoid valve for charge pressure limitation N75Low-pressure boxINOUTSSP 190/2016 Diagnosis interfaceIntake manifold temperaturesender G72Charge air coolerVacuum pump Non-return valve Low-pressure accumulator17 System overviewIntake manifold temperature sender G72Engine control unit J248Engine speed sender G28Altitude sender (integrated in engine control unit)Solenoid valve for charge pressure limitation N75Intake manifold pressure sender (integrated in engine control unit)SSP 190/21Diagnosis interface18 Engine control unitThe adjustable turbocharger is controlled by the control unit of the engine on which the turbocharger is mounted.SSP 190/22The new J248 engine control unit is equipped with a high-performance 16-bit microprocessor. The high computing power of the engine control unit allows optimum charge pressure control by altering the pulse duty factor at solenoid valve N75.The intake manifold pressure sender and the altitude sender do not have electrical abbreviations because they are integrated in the control unit.19 SensorsCharge pressure sender The charge pressure sender is integrated in the engine control unit on the 1.9 ltr. TDI engine. It is connected to the intake manifold downstream of the turbocharger by way of a pressure pipe.SSP 190/23Signal utilisation: The charge pressure is required to calculate the vane angle adjustment.Effect of signal failure: If the sender signal fails, the vanes are adjusted to a steep angle. Engine output is reduced.Fault message of self-diagnosis: Control unit defective20 Altitude sender The altitude sender is integrated in the engine control unit. It signals the current ambient air pressure to the control unit.SSP 190/25Signal utilisation: The ambient air pressure is required as a correction value for charge pressure control since air density decreases with increasing altitude. The signal is also used to control exhaust gas recirculation.Effect of signal failure: If no signal is received from the altitude sender, the constant-output turbocharger is mapped. This may lead to higher emissions and loss of power.Fault message of self-diagnosis: Control unit defective21 SensorsIntake manifold temperature sender G72 The intake manifold temperature sender is inserted in the intake manifold downstream of the air intercooler.SSP 190/26Signal utilisation: The intake manifold temperature is required as a correction value for charge pressure control. It makes allowance for the effect of temperature on the charge air density.Effect of signal failure: If the sender signal fails, the control unit uses a substitute temperature. This may lead to loss of power.Electrical circuitFault message self-diagnosis: Short to earth Interruption/short to positiveG72SSP 190/2722 Engine speed sender G28 This inductive sender registers the crankshaft speedSSP 190/28Signal utilisation: The signal of the engine speed sender is needed to calculate numerous functions of the system control unit, such as: - fuel injection quantity, - injection point, - idle control, - charger control.Electrical circuitEffect of signal failure: The engine cannot be started if no signal is received from the speed sender. If the fault occurs when the engine is running, the engine cuts out.Fault message of self-diagnosis:G28Plausibility of engine speed senderSSP 190/2923 ActuatorsSolenoid valve for charge pressure limitation N75 Solenoid valve N 75 is controlled by the engine control unit. The vacuum in the low-pressure box is set by changing the signal clocks (pulse duty factor).SSP 190/30Effect of signal failure: The solenoid valve opens. This produces atmospheric pressure in the low-pressure box. This corresponds to the adjustment used in emergency operation.Electrical circuitFault message of self-diagnosis: Short to positive Interruption/short to earthSSP 190/31N7524 Test your knowledge1. A B C DWhat is/are the effect(s) of altitude sender failure? Charge pressure is too high Higher exhaust gas emission values Failure of the altitude sender has no effect. Fault message indicating defective control unit.2. A BWhich of the following statements is correct? If engine speed sender G28 fails, then the engine can no longer be started. If engine speed sender G28 fails, fuel consumption increases because the charger control is not functioning.25 Self-diagnosisThe engine control unit allows extensive self-diagnosis of all subsystems and components. The diagnosis can be performed using the l V.A.G 1551 and l V.A.G 1552 fault readers. To connect the diagnosis you require diagnosis cable l V.A.G 1551/3fiSSP 190/32SSP 190/33The following functions are possible:02 03 08 11 Interrogate fault memory Actuator diagnosis Read measured-value block Charge pressure controlFunction 02 Interrogate fault memoryAll senders/actuators are monitored by the self-diagnosis.J248G72G28 N75 Altitude senderIntake manifold pressure senderSSP 190/3426 Function 03 Actuator diagnosisThe colour-coded components are activated during the actuator diagnosis.N75SSP 190/35Function 08 Read measured-value blockThe colour-coded components are displayed in the measured-value block.J248G72G28 N75 Altitude senderIntake manifold pressure senderSSP 190/36 27 Self-diagnosisFunction 11 Charge pressure-controlThe signals of the colour-coded components are required for monitoring the control unit.J248G28 N75Intake manifold pressure senderSSP 190/37Display group number 11 Engine speed Nom. charge pressure Actual charge pressure value Pulse duty factor of CPC28 Function diagram30 15 X 31 30 15 X 31ComponentsJ317G28 G72 Engine speed sender Intake air temperature senderJ248 Engine control unit J317 Voltage supply relay, terminal 30 N75 Solenoid valve for charge pressure limitationAThe following senders are integrated in the control unit: H Altitude sender G Intake manifold pressure senderN75422347 J24861 H G1244664338G72G28Colour codesInput signal Output signal Positive EarthSSP 190/38 29IN OUT Solutions: P.10 1. A Housing; B Exhaust gas turbine; C Compressor; D Lubricating oil inlet; E adjustable vanes 2. Inlet cross-section, adjustable vanes P.15 1. A; B 2. A B C P.25 1. B; D 2. A30Notes 31 For internal use in Service Organisation only. © VOLKSWAGEN AG, Wolfsburg All rights reserved. Subject to modification. 640.2810.09.00 Technical Status: 05/96` This paper has been manufactured from chlorine-free bleached cellulose.