TECHNICAL DOCUMENTATION

SSP 227 3,3 l V8 TDI Common Rail Injection System

PDFEN36 pages2 MB
SSP 227 3,3 l V8 TDI Common Rail Injection System - PDF cover

This PDF is currently unavailable.

Read document text
227Service.3,3 l V8 TDI Common Rail Injection SystemConstruction Features and FunctionsSelf-Study Programme 227For internal use only With its TDI engines, Audi AG has been a leader in diesel development since 1989. Its latest technological innovation, the unique V8 TDI bears testimony to this fact.Common RailA new injection system for the V8 engineGiven that it can be integrated in existing engine concepts relatively easily, the common rail system is a new alternative injection system for modern diesel engines.As with any injection system, the common rail serves the following tasks: – Supplying the diesel engine with fuel – Generating a high pressure for the injection cycle and distributing fuel to the cylinders – Injecting a precisely calculated quantity of fuel into the cylinders at the right point in time.2 ContentsPage IntroductionCommon Rail System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Components of the common railOverview of the fuel feed process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Low-pressure fuel feed Roller cell pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Gear type pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 High-pressure fuel feed High-pressure pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Valve for fuel dosing N290 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Fuel rail with high-pressure control circuit . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Regulating valve for fuel pressure N276 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Fuel pressure sender G247 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 High-pressure circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Valve-controlled injection unit (injector) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Function of injector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Engine managementMixture formation Commencement of fuel injection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . End of fuel injection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pre-injection cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vacuum control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Double flow throttle valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Function diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Actuators and sensors Hall sender G40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine speed sender G28 Engine control unit J248/J494 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel temperature sender G81 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Intake manifold pressure sender G71 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel bypass valve N312 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Valve for fuel dosing N290 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 20 21 22 24 26 28 30 32 33 33 34 34Important! Note! The Self-Study Programme informs you about designs and functions. The Self-Study Programme is not a Workshop Manual! Please refer to the relevant Technical Literature for all maintenance and repair instructions.3 IntroductionCommon Rail SystemThe common rail system comprises: – The pre-supply pump – The high-pressure pump – The fuel rail with high-pressure control circuit and – One rail element with 4 injectors per cylinder bank.Gear type pre-supply pump Fuel rail with high-pressure control circuit Fuel coolingRail elementsSSP227_001High-pressure pumpInjectors4 The Common Rail System is a pressure accumulator-type injection system. In the Common Rail System, pressure generation and fuel injection take place separately. A separate high-pressure pump housed in the inner V of the cylinder block generates pressure continuously. This pressure is accumulated inside a rail and supplied to the injectors of a cylinder bank along short injection pipes. The engine control unit controls the quantity of fuel injected into the cylinders and the injection timing by means of solenoid valves on the injectors.Advantages: – The fuel injection pressure can be selected almost at random from a range of values within the characteristic zoneInjection pressure1800 1600 bar– High injection pressures are available at low revs and in the part-throttle range – Flexible commencement of fuel injection with pre-injection cycle, main injection cycle and post-injection cycle – There is much potential for development for future dieselcombustion processes given the total flexibility with regard to injection – Exhaust-gas aftertreatment systems can be integrated optimally1200 1000 800 600 400 200 1000 2000 3000 U/min 5000Engine speed SSP227_026The common rail accumulator type injection system Pump injector element Other cam-driven systems5 Components of the common railFuel feedOverviewHigh-pressure pump Fuel rail with high-pressure control circuitRegulating valve for fuel pressure N276 Valve for fuel dosing N290Sender for fuel pressure G247Fuel cooler (low-temperature circuit water)Gear type pumpFuel filter Bimetallic fuel pre-heating valve6 Rail element, cylinder bank IIRail element, cylinder bank IInjector 5 … 8Injector 1 … 4 Fuel cooler (air) on the vehicle underbody Fuel pump G23Mechanical crash valveBaffle housingSolenoid valve for fuel bypass N312 Fuel pump (pre-supply pump) G6SSP227_0027 Components of the common railLow-pressure feedRoller cell pump (fuel pump G23) The roller cell pump (an electric pre-supply pump) is attached to the tank exterior at the right. The pump runs when the starter is operated, drawing fuel out of the baffle housing. Two suction jet pumps (entrainment pumps) driven by a pump located inside the fuel tank (pre-supply pump G6) fill the baffle housing with fuel. The task of the roller cell pump is to supply fuel with a pilot pressure of approx. 3 bar to the gear-type pump whenever the engine is started. This enables the engine to be started quickly at any fuel temperature. The roller cell pump is shut down after the engine has been started.ArmatureSuction sidePressure sideSSP227_004Grooved disc Loose rollerSuction sidePressure sideSSP227_005 Eccentric chamber 8 Gear type pump The gear type pump is a mechanical, selfpriming pre-supply pump. It is driven directly by the inlet camshaft of the right cylinder bank. The gear type pump draws fuel out of the baffle housing and pumps it into the tank along a bypass duct (bypassing the roller cell pump) after the engine starts running.The gear type pump, in turn, delivers fuel to the high-pressure pump. Advantages of the mechanical gear type pump: – Lower sensitivity to soiling (particle barrier) – Reliability – Service life – Vibration resistance 3.1 cm3 /U 40 l/h at 300 rpm 120 l/h at 2500 rpmDelivery rate Delivery rateDrive gearPump housingSuction sidePressure sideSSP227_006 9 Components of the common railHigh-pressure feedHigh-pressure pump A 3-piston pump with a controlled intake restrictor in the inner V serves as a highpressure pump. The high pressure is generated by the radial piston pump with three pump pistons arranged at an angle of 120o. The radial piston pump is driven by means of a toothed belt. Three feed strokes per revolution result in low peak torque and a even loading of the pump drive. Max. torque demand is 17 Nm at 1300 bar. This is approx. 9 times less than that of comparable distributor pumps which utilise conventional injection technology.Pump piston Eccentric Pressure spring Pump housing (section)Input shaftReturn line to the gear type pump Return line from the fuel rail Nozzle chamber from the gear type pumpValve for fuel dosing N290to the fuel rail SSP227_007Specifications Max. pressure Rev range: Delivery rate: Power consumption: 1350 bar 75 … 3000 rpm 0.6 … 0.7 cm3/U 3.5 kW at rated engine speed and at a rail pressure of 1350 bar10 Intake strokeFuel supply from the gear type pumpFeed strokeExhaust valveIntake valve High-pressure connectionCorrugated discPressure spring SSP227_025 Pump pistonThe input shaft, with its eccentric cam, moves the pistons of the three pump elements up and down in a sine-wave pattern. The gear type pump forces fuel into the nozzle chamber or the lubricating and cooling circuit of the high-pressure pump through the restrictor bore of solenoid valve for fuel dosing N290. If the fuel feed pressure exceeds the opening pressure of the safety valve (0.5 - 1.5 bar), the gear type pump can force fuel through the intake valves in the pump element thus causing the piston to move down (intake stroke).If a piston overshoots bottom dead centre, the intake valve closes due to the pressure drop. The fuel in the pump element can no longer escape. The fuel can now be compressed beyond the feed pressure of the gear type pump. The pressure which now builds up causes the exhaust valve to open once it exceeds the pressure present in the rail. The compressed fuel now enters the high-pressure circuit. The pump element delivers fuel until top dead centre is reached (feed stroke).11 Components of the common railValve for fuel dosing N290Pump pistonHigh-pressure pumpExhaust valveto railRegulating pistonLubricating oil holeIntake valve Return line, gear type pump Safety valve Supply line, gear type pumpRestrictor boreValve for fuel dosing N290SSP227_009The high-pressure pump is driven by the toothed belt of the camshaft drive whose gear ratio in relation to engine speed is i=2/3. In the part-throttle range and at high engine speeds, the high-pressure pump can feed and compress more fuel than is injected into the cylinders. To reduce the power consumption of the high-pressure pump and avoid unnecessary fuel heating at these operating points, fuel can be redirected to the fuel return line (inner circuit) by means of the solenoid valve N290.Operated condition of de-energised solenoid valve N 290 When it is de-energised, the solenoid valve is open. The control piston is pushed to the left by spring force and releases the minimum cross section to the high-pressure pump. The solenoid valve is more or less closed depending on load and engine speed. Operated condition of activated solenoid valve N290 When it is activated, the solenoid valve is closed. The control pressure drops and the control piston restricts the feed to the highpressure pump. The control pressure and therefore the piston position are changed by varying the pulse duty ratio. The fuel cut off by the solenoid valve returns to the gear pump.12 Fuel rail with high-pressure control circuitSupply line to rail Cylinder bank 1 Sender for fuel pressure G247Return line High-pressure pump Fuel railRegulating valve for fuel pressure N276SSP227_010Supply line to rail Cylinder bank 2 Supply line from high-pressure pump Return line Fuel coolerThe fuel rail accommodates the fuel pressure sender and the electric control valve for fuel pressure, and distributes the fuel evenly to the two rails under a pressure of up to 1350 bar.13 Components of the common railRegulating valve for fuel pressure N276 The regulating valve is located in the fuel rail and generates a defined pressure in the highpressure circuit in dependence upon operating point. Engine – "OFF“ In the resting position (valve de-energised), the force of the pressure spring counteracts the high pressure from the high-pressure pump. In the process, a rail pressure of approx. 100 bar builds up.Return line to high-pressure pumpPressure springSolenoid connection High pressureReturn line to tankSSP227_028Engine – "ON" To increase the rail pressure, a magnetic force is opposed to the high pressure of the highpressure pump by applying an electric current to the magnetic coil. The flow cross-section and the redirected quantity are reduced as a result. This allows the rail pressure to be set optimally by the control unit and pressure fluctuation in the rail to be compensated. The fuel quantity redirected at the pressure regulating valve returns to the tank along the return line.Magnetic coilSSP227_01314 Sender for fuel pressure G247 The fuel pressure sender measures the current pressure in the high pressure system. The sensor element records this pressure and sends a corresponding voltage signal to the engine control unit through the evaluation electronics. The supply voltage to the evaluation electronics is 5 V. The resistance drops as the pressure increases, causing the signal voltage to rise. The high-precision sender for fuel pressure is the chief component in the system.Evaluation electronics0V5+5 VSensor elementSSP227_012High-pressure connectionFuel pressure 1500 bar0V5If the fuel pressure sender fails, a fixed value is utilised for activating the regulating valve for fuel pressure, i.e. the system enters the emergency running mode.+5 VSSP227_011 Output voltage U5,00 V 4,75 V 4,65 V 4,50 VSensor defective Maximum pressure0,50 V 0,30 V 0,25 V 1500 barSSP227_027Minimum pressure Sensor defective Pressure 15 Components of the common railHigh-pressure circuit The high-pressure circuit comprises the highpressure pump, the fuel rail with regulating valve for fuel pressure, the two rails for cylinder banks I+II, as well as the individual high-pressure pipes to the injectors.The accumulated volume of fuel acts as a damper on pressure oscillation caused by the high-pressure pump and simultaneous shorttime withdrawal of fuel during the injection cycle.Rail, cylinder bank IFuel railReturn line to tank Injector SSP227_01416 Valve-controlled injection unit (injector)6Components of the injector: – – – – six-hole nozzle with injector needle hydraulic timing system solenoid valve and fuel ducts57 8Very narrow injectors with a diameter of 17 mm are used in view of the limited space available in the cylinder head. The fuel is conveyed from the high-pressure connection along a duct to the nozzle and into the valve timing space through the feed restrictor. The valve timing space is connected to the fuel return line via the return restrictor. The return restrictor can be opened by means of a solenoid valve.4 39 2 10Specifications Pick-up current Activation Pressure range1 Dia. of injection holes in nozzle 20 A max. 300 µs up to 80 volts 20 … 1350 bar 6 x 0.15 mm12 1 1113High pressure Return pressure14 SSP227_0301– 2– 3– 4– 5– 6– 7–Injector spring Valve timing space Return restrictor Solenoid valve armature Fuel return line (to tank) Electrical connection, solenoid valve Solenoid valve8 9 10 11 12 13 14– – – – – – –Fuel supply - high pressure from rail Valve ball Feed restrictor Valve timing piston Nozzle intake duct Chamber volume Injector needle17 Components of the common railFunction injector Resting position - engine "OFF“ The fuel from the rail is constantly present at the high-pressure connection of the injector. The fuel floods the chamber volume and the valve timing space through the feed restrictor. – There is a constant pressure between the chamber volume and the valve timing space. – The solenoid valve of the injector is closed.High-pressure connectionFeed restrictorValve timing spaceA pressure of 1.5 times the area of the control piston facing towards the injector is generated in order to make sure that the injector is leak-tight. This means that the force exerted by the hydraulic control piston is approx. 50% higher than the nozzle opening force; in addition to the injector spring, the valve control piston presses the injector needle into its seat. The injector spring keeps the injector closed up to a pressure difference of approx. 40 bar between the chamber volume and the valve timing space.Valve control pistonInjector spring Chamber volumeSSP227_015 Injector needle18 Start of fuel injection - engine "ON" If an electric current is applied to the solenoid valve, the magnetic force will be greater than the closing force of the solenoid valve spring. The solenoid valve opens the return restrictor, relieving the fuel pressure in the valve timing space and reducing the closing force above the nozzle. As a result, the excess fuel and/or rail pressure below the nozzle increases as from an excess pressure of approx. 160 bar on the nozzle side, causing the nozzle to open. The opening velocity of the injector needle is dependent upon the application of a high current for a short time and the return to feed restrictor cross-section ratio.Magnetic valve springReturn restrictorFeed restrictor Valve timing spaceThe return restrictor cross-section must be greater than the feed restrictor cross-section before injector needle can open at all.Injector needle SSP227_01619 Engine managementMixture formationCommencement of fuel injection If current is applied to the solenoid valve for longer, the valve control piston and injector needle will rise up to the control piston stop. The nozzle is now open as far as it will go, and fuel is injected into the cylinders under approximately the same pressure as in the rail. End of injection If the solenoid valve is de-energised, the valve spring again presses the solenoid valve armature or the valve ball down onto the valve seat. The return restrictor is closed and the pressure in the control space rises to system pressure. The closing force acting upon the nozzle above the control piston is greater than the opening force of the nozzle applied to the seat. This causes the injector to close.The solenoid valve opens completely during each injection cycle, even if only a very small quantity of fuel is to be injected. In contrast to previous injection systems, injector closure is controlled even if the system pressure is very high (sharp end of injection drop).To inject a small quantity of fuel, the solenoid valve is only energised (clocked) for a short period to time. The injector needle is not opened as far as it will go, it is only raised slightly. The quantity of fuel injected into the cylinders is defined by: – – – – – solenoid valve activation time needle opening and closing velocity needle lift hydraulic flow rate of nozzle rail pressure20 Pre-injection cycle250200Needle lift [µm]150Injection pattern100500 0.00 1.00 2.00 3.00 4.00Pre-injection cycleMain injection cycleTime [µs] SSP227_017The object of the pre-injection cycle is to reduce combustion noise, exhaust emissions and fuel consumption. The pre-injected quantity of fuel prepares the combustion chamber for the main quantity to be injected with respect to pressure and temperature for the main injection quantity. The main injection quantity is injected into the prechamber. Advantage: – The spark lag for the main injection cycle is shortened. – This system produces less noise than conventional diesel engines thanks to the reduced combustion pressure peaks. – Optimal combustion of the fuel mixture takes place.SSP227_029 Top dead centre Combustion pressurePressure curve with pre-injection cycle Pressure curve without pre-injection cycle Needle lift curveThe pre-injection cycle controls the combustion pressure curve by means of the following variable: – Pre-injection quantity – Distance to main injection cycle at increasing engine rpmThe figure shows the difference between the pressure curves of a combustion process with and without a pre-injection cycle.21 Engine managementVacuum controlJ248G70G246AN213 G2/G62 G28 G40N18NG71C22 A B C G28 G40 G70 G71 G246 J248 N18 N75 N213BVacuum pump Brake servo Throttle valve Engine speed sender Hall sender Air-mass flow meter Intake manifold pressure sender Air-mass flow meter 2 Diesel direct injection system Control unit EGR valve Cylinder bank 1 Charge pressure control solenoid valve Exhaust gas recirculation valve -2Solenoid valve 2 for charge pressure control Intake manifold flap change-over valveG2/G60 Coolant temperature senderN274 N239In the V8 TDI engine, an engine-driven vacuum pump (A) supplies a sufficient quantity of medium required for vacuum control. In addition to the brake servo (B), the vacuum controls the exhaust gas turbocharger, the EGR valve and the two throttle valves (C) in the intake module.N75 N239Charge pressure data is acquired via the intake manifold pressure sender (G71). The signals from the two hot-film air mass meters (G70/G246) are utilised for controlling the turbocharger via the charge pressure limiting valves (N75, N274). The throttle valves (C), activated by intake manifold flap change-over valve N239, are in operation when the engine is shut down for a short time.N274SSP226_02723 Engine managementDouble-flow throttle valve The double-flow throttle valve is closed when the engine is shut down for a short time. Advantages: The engine does not run on after it has been shut down and no unburned fuel enters the cylinders (when the engine is restarted, fewer unburned particles are emitted).Throttle valveCharge pressure intake manifold pressure G71SSP226_026 Vacuum box for throttle valve positioningThe two throttle valves are fully open in the rest and full-throttle positions.24 Notes25 Engine managementSystem overviewSensorsHot-film air mass meter G70/G246Engine speed sender G28Automatic gearbox control unit J217Coolant temperature sender G2 and G62 Combination processor in the dash panel insert J218Sender for oil temperature G8Fuel temperature sender G81 Sender for fuel pressure G247 Operating and display unit for air conditioning system E82Intake manifold pressure sender G71 Accelerator pedal sender with accelerator position sender G79 and idling speed switch F60ESP control unit J104 Brake light switch F and Brake pedal switch F47Kick-down switch F8Diesel direct injection system control unit J248Hall sender G40Auxiliary signals: Cruise control system Coolant temperature sender DF signal Terminal 50 Speed sensor signal Crash signal from airbag control unit High pressure sensor G65 A/C ready Auxiliary heater coolant 26Control unit 2 for diesel direct injection system J494 ActuatorsSolenoid valve for injector, cylinders 5-8; N83 – N86 Glow plug relay J52 Glow plugs 1-4; Q6Relay 2 for glow plugs J495 Glow plugs 5-8; Q6 Intake manifold flap change-over valve N239Regulating valve for fuel pressure N276EGR valves 1 + 2; N18 + N213Solenoid valve for fan control N313Auxiliary signals: Air conditioner compressor Auxiliary heater, coolantElectro/hydraulic engine mounting left/ right, solenoid; N14427/N145Charge pressure control solenoid valves 1+ 2; N75/N274Relay for pump charge air cooling J536 Pump for charge air cooling V188 Diagnostic connection Electric fuel pump II relay J49 Fuel pump G23 Solenoid valve for injector, cylinders 1-4; N30 – N33Fuel bypass valve N312 Auxiliary signals: Fan speeds 1+2 Valve for fuel dosing N290 Fuel pump relay J17 Fuel pump (pre-supply pump) G6 Pump relay, fuel cooling J445 Pump for cooling fuel V166 Alternator cut-in relay J442 SSP227_018 27 Engine managementFunction diagramCode codes= Input signal = Output signal Components A E45 D F F8 F47 F60 G2 G6 G8 G23 G28 G40 G62 G70 G71 G79 G81 G246 G247 J17 J49 J52 J248 J317 J442 J445 J494 J495 J536 M9 M10 N18 N30 N31 N32 N33 N75 N83 N84 N85 N86 N144 N145 28 Battery Cruise control system switch Ignition switch Brake light switch Kick-down switch Brake pedal switch for cruise control system Idling speed switch Coolant temperature sender Fuel pump (pre-supply pump) Oil temperature sender Fuel pump Engine speed sender Hall sender Coolant temperature sender Air-mass flow meter Intake manifold pressure sender Accelerator position sender Fuel temperature sender Air-mass flow meter Fuel pressure sender Fuel pump relay Electric fuel pump II relay Glow plug relay Diesel direct injection system control unit Voltage supply relay Terminal 30 Alternator cut-in relay Pump relay, fuel cooling Diesel direct injection system control unit Glow plug 2 relay Pump relay, charge air cooling Brake light bulb, left Brake light bulb, right EGR valve Solenoid valve for injector, cylinder 1 Solenoid valve for injector, cylinder 2 Solenoid valve for injector, cylinder 3 Solenoid valve for injector, cylinder 4 Solenoid valve for charge pressure control Solenoid valve for injector, cylinder 5 Solenoid valve for injector, cylinder 6 Solenoid valve for injector, cylinder 7 Solenoid valve for injector, cylinder 8 Electro/hydraulic engine mounting left, solenoid Electro/hydraulic engine mounting right, solenoid N213 N239 N274 N276 N290 N312 N313 Q6 S ST S204 V166 V188 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Exhaust gas recirculation valve -2Intake manifold flap change-over valve Solenoid valve 2 for charge pressure control Regulating valve for fuel pressure Valve for fuel dosing Fuel bypass valve Solenoid valve for fan control Glow plug Fuse Fuse carrier Fuse, terminal 30 Pump for cooling fuel Pump for charge air cooling Fan speed 2nd fan speed Terminal 61, alternator Coolant temperature Sensor earth Speed sensor signal Terminal 50 DF signal Crash signal from airbag control unit Additional heater, coolant Additional heater, coolant High pressure sensor G65 A/C ready Air-conditioner compressor signal Terminal 30a = Positive = Earth = Bidirectional = CAN-BUSCAN-BUS L CAN-BUS H X Y Z ...} Connection to databusTerminals within the function diagram Diagnostic connection (K-wire) 29 Engine managementActuators and sensorsHall sender G40 The inlet camshaft of the second cylinder bank has a ferro-magnetic tooth. When the tooth passes by the phase sensor, a voltage signal (Hall voltage) is generated for a short time. The camshaft signal is generated once per revolution of the camshaft and indicates the position of the 1st cylinder to the master control unit in the compression phase.Ferro-magnetic toothSSP227_021Engine speed sender G28 The engine speed sender is an inductive sender. It acquires engine speed data and the exact angular position of the crankshaft.Engine speed sender G28If the engine speed sender fails, engine operation will not be possible.Segment gapSender wheel SSP227_032 30 Signal pattern from engine speed sender G28 and Hall sender G40 as generated by the oscilloscope function of the VAS 5051 10 V/div. 20 ms/div.Auto modeG405 V/div. # "20 ms/div.& $ ! %G286SSP227_022 Indication of the software reference mark 5 V/div. 10 ms/div. Auto modeG40G28SSP227_023 Sender wheel Reference mark 108o before TDC, 1st cylinder TDC, 1st cylinderThe reference mark is the point at which the control unit sets the crank angle to 0 (initialisation).This reference mark is located approx. 108o crank angle before ignition TDC of the 1st cylinder.31 Engine managementEngine control unit J248/J494 In the V8 TDI, two engine control units, one master control unit and one slave (auxiliary) control unit are responsible for engine management. The master control unit performs all the functions which are required to calculate and control parameters, e.g. injection point and injection period. 80 volts are required in order to activate the injectors for a short time. This calls for more highly rated output stages and capacitors. Therefore, the injectors of bank 2 can only by operated from the master control unit and the injectors of bank 1 can only be operated from the slave control unit. The slave control unit controls the following electrical components: – Fuel bypass valve N312 – Valve for fuel dosing N290 – Fuel pump relay J17 and fuel pump (presupply pump) G6 – Pump relay, fuel cooling J445 and pump for cooling fuel V166 – Alternator cut-in relay J442 (option) – Fan (stage 1+2).Diesel direct injection system control unit J248Diesel direct injection system control unit 2 J494SSP227_031Self-diagnosis master control unit slave control unitAddress word 01 11The control units intercommunicate by CAN-BUS. The master control unit indicates to the slave control unit what functions it has to execute.SSP186 describes how the CAN-BUS works.32 Fuel temperature sender G81 The fuel temperature is acquired in the return line of the injectors. The temperature signal influences the following: – The valve for fuel dosing N290 (the quantity of fuel to be compressed is regulated in order to reduce the temperature) – The rail pressure – The injection quantity for fuel temperatures over 118°C. The sensor is of NTC type (negative temperature co-efficient).SSP227_003If the sender fails, no substitute signal is utilised.Intake manifold pressure sender G71 is a piezo-electric pressure sensor and is linked to the induction module by a hose pipe. The signal is used for: – charge pressure control If the sensor fails, the charge pressure control is switched off.Result: Loss of engine powerSSP227_00833 Engine managementFuel bypass valve N312 The valve is integrated in the bypass of the electric pre-supply pump. It opens for 40 seconds when the ignition is turned "ON" (terminal 15) and closes during the starting cycle (terminal 50). When the engine speed signal is input, the solenoid valve opens and allows fuel to be withdrawn directly from the baffle housing, bypassing the electric pre-supply pump.Valve for fuel dosing N290 The valve for fuel dosing (intake restrictor) returns the fuel in accordance with power demand. As a result, the quantity of fuel pumped and compressed is only slightly more than the quantity of fuel injected. The power demand of the pump and fuel heating are reduced in this way. If a malfunction occurs, the following happens: – The exhaust gas recirculation is switched off – The charge pressure control is switched off – Full-throttle limitationSSP227_020 High-pressure pumpTo protect the engine when a fault in the system is registered, the engine is forcibly shut down via the intake restrictor.34Valve for fuel dosing N290 Notes35 All rights reserved. Subject to technical modifications. AUDI AG Abteilung I/VK-5 D-85045 Ingolstadt Fax 0841/89-36367 940.2810.46.20 Technical status 07/99 Printed in Germany227