TECHNICAL DOCUMENTATION

SSP 265 Vehicle electrics in Polo Model Year 2002

PDFEN48 pages3 MB
SSP 265 Vehicle electrics in Polo Model Year 2002 - PDF cover

This PDF is currently unavailable.

Read document text
Service.Self-Study Programme 265Vehicle electrics in Polo Model Year 2002 265_061The range of electrical systems in new vehicles is expanding increasingly as a result of the ever more effective safety systems and enhanced convenience systems. The vehicle electrics in the Polo Model Year 2002 have been reorganised with the aim of retaining a clear arrangement within the comprehensive onboard power supply. A major role in this connection is played by a onboard power supply control unit. It monitors the capacity utilisation of the onboard power supply and performs functions which, until now, were executed by separate relays and control units. Moreover, the databus diagnostic interface, which permits data transfer between different CAN databus systems, is also integrated in the onboard power supply control unit.NEWImportant NoteThe Self-Study Programme describes the design and function of new developments! The contents are not updated.Please always refer to the relevant service literature for up-to-date inspection, adjustment and repair instructions.2 At a glanceIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Onboard power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Onboard power supply control unit . . . . . . . . . . . . . . . . . . 13Function diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22CAN databus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24Databus diagnostic interface . . . . . . . . . . . . . . . . . . . . . . . . . . . .26Special functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30Convenience and safety electronics . . . . . . . . . . . . . . . . . .32Sliding/tilting roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Dash panel insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42Self-diagnosis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44Test your knowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .463 IntroductionThe vehicle electrics of the Polo Model Year 2002 have been redesigned in terms of its concept and its structure. The onboard power supply control unit plays a central role in this connection. It performs a wide range of new check, monitoring and relay functions. The other control units are located decentralized within the vehicle. In the pages which follow you will be able to familiarize yourself with the following subjects of the electrical system of the Polo Model Year 2002: – Design of onboard power supply – Tasks and functions of onboard power supply control unit – Design of CAN databus system – Tasks of databus diagnostic interface – Presentation of convenience and safety electronics – Design and functions of the dash panel insert – Lighting conceptClimatic/CLIMAtronic control unit ABS control unitOverview of control units in the PoloRadio or Radio-navigation systemAirbag control unitPower steering control unit4 Door control unit passenger sideSliding roof adjustment control unitRear right door control unitControl unit with display unit in dash panel insertRear left door control unit265_013Door control unit driver sideOnboard power supply control unit with gatewayEngine control unitAutomatic gearbox control unitConvenience system central control unit5 Onboard power supplyOnboard power supplyThe onboard power supply is a decentralized design. The most important stations are:265_006 265_007Coupling stations in A-pillar and B-pillarLKIHDCBAPNMGFE265_005Compact connector265_008Fuse holder265_012265_009Main fuse carrier12 6 7 123 8 134 9 14 15265_0105 10 11265_011 265_021Voltage distributorOnboard power supply control unitRelay carrier6 Main fuse carrierThe main fuse carrier is located on battery cover. The number of fuses always depends on the equipment fitted to the particular model. The main fuse carrier houses up to 6 strip fuses and 10 plug-in fuses. A voltage cable provides the connection to the battery (positive). The fuses protect the individual power circuits immediately downstream of the battery from overloads.265_009Voltage distributorThe voltage distributor is located on the driver side behind the dash panel cover. The voltage distributor is responsible for distributing the current of terminal +30 from the main fuse carrier on the battery to the individual electrical components.265_0107 Onboard power supplyFuse holderThe fuse holder is located behind the cover in the left side of the dash panel. There are two types of fuses for protecting the power circuits: – Mini-fuses up to 15 A – Little fuses more than 15 A This combination offers the following advantages: – greater number of fuses within the same space – greater number of individually protected circuits These fuses are identified in the current flow diagram with the abbreviated designation „SB“.Mini-fuseLittle fuse265_008Position 1 2Relay Not assigned Motronic power supply relay Glow plug relay Fuel pump relay (diesel engines) Entry warning light relay Headlight washer system relay Starter lockout relay Low heating capacity relay High heating capacity relay Simos control unit power supply relay Relief relay for X contact Fuel supply relay Fuel pump relay (petrol engines) Fuse carrier for electric auxiliary heater Diesel direct injection system relayRelay carrierThe relay carrier is located on the driver side behind the dash panel cover. Compared to the design consisting of mini electrical centre and additional relay carrier, the relay carrier of the Polo is a single component with standardized design for accommodating the relays.3 4 5 6 7 8 9 101 5 10 11 62 7 123 8 134119 14 1512 13 14265_021158 Coupling stationsThe purpose of the coupling stations is to link the electrical components in the doors to the rest of the onboard power supply. The coupling stations permit: – easy access – separation of the wiring looms to the doors – simplified fault findingA-pillar coupling station: It is located close to the top door hinge at the A-pillar. This coupling station combines the plug connections to the following electrical components in the doors: – – – – loudspeaker exterior mirror lock unit warning light265_006B-pillar coupling station: It is located close to the top door hinge of the rear door at the B-pillar. This coupling station combines the plug connections to the following electrical components in the doors: – loudspeaker – lock unit265_0079 Onboard power supplyCompact connectorThe compact connector links the part of the onboard power supply in the engine compartment to the part of the onboard power supply in the interior. The onboard power supply is designed in such a way that all the cables of the components or the two wiring looms (engine compartment, interior) merge in their individual connectors of the modules on the relevant side of the compact connector. The connection is created by means of the individual connectors of the modules, irrespective of the equipment or version variants. The connector provides a straightforward means of separating the onboard power supply at this point. This greatly facilitates test operations as well as removal and installation work.Bulkhead Middle part of dash panelCoupling stations Roof module Coupling connector265_022BatteryCompact connector Fuse carrierCoupling connector Coupling station10 Design of the compact connector The compact connector is located in the left of the bulkhead, behind the wiper linkage. It is accessible from the engine compartment as well as from the interior.Compact connectorView from engine compartmentPartition wall connectorSecuring screws265_075View from interiorCompact connectorLock for single connectors Single connector265_07611 Onboard power supplyThe compact connector is subdivided into various modules. The connections are created by means of mechanically coded connectors of different colours for the individual modules.Compact connector View from engine compartmentLKIHDCBAPNMGFE265_005Connector assignment Module A B ABS, ESP Gearbox, engine, K wire, clutch pedal switch Engine power supply Light, cruise control system, drivetrain CAN databus Anti-theft alarm system Battery +30 Dash panel insert Responsible for Module H I Responsible for Not assigned Additional heater, accelerator pedal position sender, brake pedal switch Engine, dash panel insert AC, radiator fan controlC DK LE F GM N PABS, ESP Diesel glow plug system Windscreen wash and wipe system12 Onboard power supply control unitOnboard power supply control unit J519Within the vehicle onboard power supply, the control unit plays a central role. It has functions which were previously performed by separate relays and control units. The onboard power supply control unit performs the following functions: – – – – – – – – – – – – Load management Interior light control Fuel pump feed control Windscreen wash and wipe control, intermittent and rain sensor mode Exterior mirror and rear window heater Rear seat backrest monitoring Turn signal and hazard warning light control Horn control Cruise control system (supplying signals over drivetrain CAN databus) Remote release of boot lid/tailgate Instrument and switch lighting Maintaining operation of sliding roof and power windowsConnector mount265_014Connector mountDepending on the level of equipment, functions of differing extent are integrated in the control unit. Consequently, there are also variations in the positioning of the connector mounts.Additional functions on models fitted with automatic gearbox: – Actuation of selector lever lock solenoid – Starter lockout – Actuation of reversing lightsImplementation of the onboard power supply control unit has made it possible to cut vehicle weight by reducing the extent of wiring and plug connections as well as a number of relays and control units.Fitting location The onboard power supply control unit is positioned on the driver side behind the dash panel cover.265_01513 Onboard power supply control unitLoad managementThe wide range of convenience functions and electrically heated components such as seat heater, rear window heater, exterior mirror heaters and electric auxiliary heater (heating element for auxiliary heater Z35) can result in an overload of the alternator when driving and thus in a drain on the battery. This is particularly the case when driving extremely short distances and in winter as well as stop- and go journeys and vehicles with a high level of equipment. The load management of the onboard power supply control unit regularly monitors the battery voltage, while taking into account the power demand of short-term consumers. If it detects a voltage deficit in the onboard power supply, the control unit initiates measures to maintain vehicle operation and to ensure that the vehicle can be restarted.Electrical circuitGCA C J... J131 J132 J255 J301 J519 J533 Z1 Z4 Z5 Z6 Z7 Z8 Z9Battery Alternator Engine control unit Heated driver seat control unit Heated passenger seat control unit CLIMAtronic control unit AC control unit Onboard power supply control unit Databus diagnostic interface Heated rear window Heated exterior mirror, driver side Heated exterior mirror, passenger side Heated driver seat Heated driver backrest Heated passenger seat Heated passenger backrestJ ...AJ533J519J255/ J301J131 Z1 Z4 Z5J132Z6Z7Z8Z9265_04614 Idling speed is increased if onboard onboard power supply voltage drops below 12.7 V. If voltage drops below 12.2 V, onboard power supply control unit additionally switches off the following components:If specified voltage is again reached, onboard power supply control unit takes the following measures:1Increases idling speedReduces idling speed52Switches off rear window heaterSwitches on rear window heater43Switches off seat heatersSwitches on seat heaters34Switches off exterior mirror heatersSwitches on exterior mirror heaters25Reduces AC compressor capacityACIncreases AC compressor capacityAC115 Onboard power supply control unitInterior light controlIf the switches of the front and rear interior lights are in the door contact position, the onboard power supply control unit J519 ensures that – the interior lights are switched off after 10 minutes when the car is parked with the doors opened, to thus avoid any unnecessary drain on the battery. – the interior lights are switched on for 30 seconds when the car is unlocked or the ignition key withdrawn. The interior lights are switched off immediately when the car is locked or the ignition is switched on. – the interior lights are switched on in the event of a crash. A further task of the interior light control is to switch off any lights which have been switched on manually (front and rear interior lights and reading lights, luggage compartment light, glove box light and vanity mirror lights) about 30 minutes after the ignition is switched off. This function is likewise a protection for the battery capacity.Door contact positionFront interior light265_062Door contact position265_063Rear interior lightIf the switches of the interior lights are not in the door contact position, the interior lights are not switched on in the event of a crash.16 F11* F3* F10* F2* F220** F221** F222** F223**+30 +15 DCAN-K CAN-AJ519W18W20W14W6W19 W W13W43265_059Electrical circuit CAN-A CAN-K D F2 F3 F10 F11 F220 F221 F222 F223 Drivetrain CAN databus Convenience CAN databus Ignition/start switch Door contact switch, driver side Door contact switch, passenger side Left rear door contact switch Right rear door contact switch Central locking lock unit, driver side Central locking lock unit, passenger side Central locking lock unit, rear left Central locking lock unit, rear right J519 W W6 W13 W14 W18 W19 W20 W43 Onboard power supply control unit Front interior light Glove box light Reading light passenger side Illuminated vanity mirror (passenger side) Left luggage compartment light Reading light driver side Illuminated vanity mirror (driver side) Rear interior light* **on models not fitted with central locking on models fitted with central locking17 Onboard power supply control unitFuel pump supply controlThe petrol engines in the Polo Model Year 2002 feature a new fuel pump supply control. Two parallel relays - the fuel pump relay J17 and the fuel supply relay J643 - take the place of the individual fuel pump relays with integrated crash fuel shutoff. Both relays are located on the relay carrier above the onboard power supply control unit J519.F2* F220** +15J519Operating principle When the driver door is opened, a signal is transmitted by the door contact switch F2 (or by the central locking lock unit F220) to the onboard power supply control unit. This in turn actuates the fuel supply relay J643 and the fuel pump G6 runs for about two seconds. A time switch in the onboard power supply control unit prevents – the fuel pump constantly running if the driver door is opened at short intervals. – the fuel pump again being operated if the driver door remains open for more than 30 minutes. When the ignition is switched on or the engine started, the fuel pump G6 is operated through the fuel pump relay J17 by the engine control unit.J...J643J17G6M265_045Electrical circuit F2 Door contact switch driver side F220 Central locking lock unit, driver side G6 Fuel pump J... Engine control unit J17 Fuel pump relay J519 Onboard power supply control unit J643 Fuel supply relay* **on models not fitted with central locking on models fitted with central locking18 Activating rear screen wiperWhen reverse gear is engaged, the rear screen wiper automatically makes a single sweep. The following conditions must be met for this purpose: – windscreen wiper switched on with stage 1 or 2 or – intermittent wipe (speed-responsive intermittent mode or rain sensor mode) switched onJ519 F4 E22 VMElectrical circuit E22 F4 J519 V V12 Intermittent wiper switch Reversing light switch Onboard power supply control unit Windscreen wiper motor Rear screen wiper motorMV12265_038Blocking windscreen wipersIf the windscreen wipers are operating in the intermittent wipe mode (speed-responsive intermittent mode or rain sensor mode) and at the same time the bonnet is opened, a signal is transmitted by the bonnet contact switch F266 to the onboard power supply control unit. The control unit blocks the movement of the windscreen wipers until the bonnet is again closed. This function is intended as a safety measure when carrying out work on the car. Electrical circuitE22F266J519MVE22 F266 J519 VIntermittent wiper switch Bonnet contact switch Onboard power supply control unit Windscreen wiper motor265_03719 Onboard power supply control unitExterior mirror and rear window heatersAs a protection for the battery capacity, it is only possible to switch on the exterior mirror and the rear screen heaters when the engine is running. The heaters are switched off automatically again after about 20 minutes. Electrical circuit C E230 E231 J519 Z1 Z4 Z5 Alternator Heated rear window push button Exterior mirror heater push button Onboard power supply control unit Heated rear window Heated exterior mirror, driver side Heated exterior mirror, passenger sideJ519E230E231CGZ1Z4Z5265_056Monitoring rear seat backrestCars fitted with a three-point inertia reel seat belt for the middle seat of the rear seat bench feature a rear seat backrest monitoring function. If the backrest part for the middle seat of the rear seat bench is not correctly locked, a warning light in the dash panel insert comes on for about 20 seconds after the ignition is switched on. Electrical circuit CAN-K Convenience CAN databus F316 Right backrest contact switch J285 Control unit with display unit in dash panel insert J519 Onboard power supply control unit K Dash panel insert K193 Backrest lock warning lamp, rear seatF316 +15J519CAN-KK193 J285 K265_05720 Turn signal and hazard warning light controlThe following functions are performed by the onboard power supply control unit J519: – Left, right turn signals – Hazard warning lights (switched on manually or in the event of crash) – Anti-theft alarm - flashing lights – Central locking - flashing lights when car unlocked/locked – Left, right trailer turn signal lightsE2E229CAN-KCAN-AJ519Electrical circuit CAN-A CAN-K E2 E229 J519 M5 M6 M7 M8 M18 M19 Drivetrain CAN databus Convenience CAN databus Turn signal light switch Warning light push button Onboard power supply control unit Bulb for left front turn signal light Bulb for left rear turn signal light Bulb for right front turn signal light Bulb for right rear turn signal light Bulb for left side turn signal light Bulb for right side turn signal lightM5 M6 M18 M7 M8 M19265_058Equipment which has to be coded:CodingThe extent of the equipment and the national version of the vehicle determine the coding of the onboard power supply control unit. This coding is factory-set. If any modifications are made to the extent of the equipment in the service sector or when carrying out repairs, for example installing heated seats or attaching trailer coupling, or replacing control unit, it is then necessary to re-code the control unit. This new code number should be entered using the „Guided fault finding“ mode with the Vehicle Diagnostic, Testing and Information System VAS 5051.Fuel pump supply control Rear window wiper with convenience setting Remote release of boot lid/tailgate Rain sensor Headlight washer system Heated exterior mirrors Heated windscreen Heated seats 4-door version Interior light control Electric load management active Towing device21 Onboard power supply control unit+30 +15 31Function diagramLegendD/50 D/86s E2/L J59 G213 J39 V11ME2/RE1/SRAJ17 J39 J59 J131 J132 J207 J245 J285J207* BY7 F4** MA B C/L CAN-A/H CAN-A/L CAN-K/H CAN-A/L D/50 D/75 D/86s E1/SRA E2/L,RST D/75J5191 + M A E230 L76 K10 Z1 H H1 V V12 F2 F3 E229 E38 C/L E22 E34 M5 M18 M6 M7 M19 M8 L76 F10 F11 M M V5 F266J393 J519 J533 J643 K10 K142 L44 L76 L101 M5 M6 M7 M8 M16 M17 M18 M19 N110 ST V V5 V11 V12 V53 W W6 W13 W14 W18 W19 W20 W43 Y7 Z1 Z4 Z5 Z6 Z7 Z8 Z9Fuel pump relay Headlight washer system relay X contact relief relay Heated driver seat control unit Heated front passenger seat control unit Starter inhibitor relay Sliding roof adjustment control unit Control unit with display in dash panel insert Convenience system central control unit Onboard power supply control unit Databus diagnostic interface Fuel supply relay Heated rear window warning lamp Selector lever position P/N warning lamp Seat heating switch light bulb Button illumination Selector lever display illumination Front left turn signal light bulb Rear left turn signal light bulb Front right turn signal light bulb Rear right turn signal light bulb Left reversing light bulb Right reversing light bulb Left side turn signal light bulb Right side turn signal light bulb Selector lever lock solenoid Fuse carrier on battery Windscreen wiper motor Windscreen washer pump Headlight washer system pump Rear window wiper motor Central locking motor - tailgate/boot lid Front interior light Glove box light Front passenger reading light Illuminated vanity mirror - front passenger side Left luggage compartment light Reading lamp - driver side Illuminated vanity mirror - driver side Rear interior light Automatic anti-dazzle interior mirror Heated rear window Heated exterior mirror, driver side Heated exterior mirror, front passenger side Heated driver seat cushion Heated driver seat backrest Heated front passenger seat cushion Heated front passenger seat backrest-31Battery Starter Alternator/terminal L Drivetrain CAN/High Drivetrain CAN/Low Convenience CAN/High Convenience CAN/Low Ignition/starter switch/terminal 50 Ignition/starter switch/terminal 75 Ignition/starter switch/terminal 86s Light switch/terminal HWS Turn signal switch/positive connection left, right turn signal E22 Intermittent wiper switch E34 Rear wiper switch E38 Intermittent wiper control E45 CCS switch E94 Heated driver seat adjuster E95 Heated front passenger seat adjuster E227 CCS button (set) E229 Hazard warning lights button E230 Heated rear window button E231 Exterior mirror heating button E234 Tailgate/boot lid handle release button F2 Door contact switch - driver side F3 Door contact switch - front passenger side F4 Reversing light switch F5 Luggage compartment light switch F10 Rear left door contact switch F11 Rear right door contact switch F124 Contact switch in lock cylinder for tailgate/ boot lid anti-theft alarm system/central locking system F125/P-N Multifunction switch/terminal P-N F147 Vanity mirror contact switch, driver side F148 Vanity mirror contact switch, front passenger side F218 Tailgate/boot lid central locking switch F220 Central locking lock unit, driver side F221 Central locking lock unit, front passenger side F222 Central locking lock unit, rear left F223 Central locking lock unit, rear right F266 Bonnet contact switch F316 Right backrest contact switch G59 Driver seat temperature sensor G60 Front passenger seat temperature sensor G213 Rain sensor H Horn plate H1 Horn J... Engine control unit* ** • ••On models fitted with automatic gearbox On models not fitted with automatic gearbox On models fitted with central locking On models not fitted with central locking= Input signal= Output signal= Positive22 +30 +15 31 Z7 Z911Z7G59 Z8G60N110* L101* F125/P-N* L44 E94 L44 E95K142*M16M17J...E45CAN-A/HCAN-A/LCAN-K/H J132 J533 J285 E231 Z4 Z5E227 J131 1V53M F5 F218 W19 W W13 W43 W6 W20 W14 J245 J643W18E234J393F124 F147 F148265_016F220F221F222F223CAN-K/L 31F316= Earth= Bidirectional wire= CAN databus= Diagnosis connection CAN databusDrivetrain CAN databusThe Polo features a CAN databus system, consisting of the drivetrain CAN databus and the convenience CAN databus. They differ in terms of their transmission rate and their data content. The drivetrain CAN databus operates with a transmission rate of 500 kBit/s in order to achieve rapid data transfer within the safetyrelevant systems.Onboard power supply control unit J519 with databus diagnostic interface J533 (gateway)Steering angle sender G85Diagnostic connectionControl unit with display unit in dash panel insert J285Engine control unit J...ABS control unit J104Airbag control unit J234Automatic gearbox control unit J217Power steering control unit J500265_02324 Convenience CAN databusThe convenience CAN databus operates with a transmission rate of 100 kBit/s.Onboard power supply control unit J519 with databus diagnostic interface J533 (gateway)CLIMAtronic control unit J255 AC control unit J301Diagnostic connectionConvenience system central control unit J393Control unit with display unit for radio and navigation J503Door control unit, driver side J386Door control unit, passenger side J387Left rear door control unit J388Rear right door, control unit J389265_02425 CAN databusDatabus diagnostic interface J533The databus diagnostic interface J533 (gateway) is integrated in the onboard power supply control unit J519. The databus diagnostic interface J533 performs 2 tasks: 1st task It is responsible for the data transfer between the two CAN databus systems – drivetrain CAN databus and – convenience CAN databus.265_065GatewayDatabus diagnostic interface J533Drivetrain CAN databusConvenience CAN databus265_018Direct communication between the systems is not possible because of the different transmission rates. A link is required for exchanging information between the systems. This link is achieved by means of the databus diagnostic interface J533.The gateway receives the data arriving from a BUS system and relays the data to each other BUS system.26 Example of data transfer between the CAN databus systemsControl unit with display unit in dash panel insertOutside temperature sensorDrivetrain CAN AC control unit Engine control unit, e.g. – coolant temperature – engine speedConvenience CANOnboard power supply control unit with databus diagnostic interface (gateway)265_020Multiple use of information of different systems over the CAN is a feature of modern vehicle electrics. For example, data messages from the drivetrain CAN are used in the convenience CAN for controlling the automatic air conditioning (Climatic). The AC control unit is connected to the convenience CAN. The following example shows the information flow from the drivetrain CAN to the convenience CAN. – The outside temperature is detected by the temperature sensor in the bumper and relayed to the control unit with display unit in the dash panel insert. This is connected to the drivetrain CAN.– Specific engine characteristic data, e.g. coolant temperature, engine speed, are detected by the engine control unit and made available to the drivetrain CAN. The messages from the drivetrain CAN are relayed over the convenience CAN in the databus diagnostic interface (gateway). The AC control unit is now in a position to read these messages and to use them for controlling the air conditioning system.27 CAN databus2nd task The databus diagnostic interface J533 receives diagnostic data from the drivetrain CAN databus and from the convenience CAN databus and relays it over the K wire, and vice versa. This makes it possible to use data from the Vehicle Diagnostic, Testing and Information System VAS 5051 for self-diagnosis. The engine control unit, the automatic gearbox control unit and the convenience system central control unit have a separate K wire.Engine control unitAutomatic gearbox control unitConvenience system central control unitDatabus diagnostic interface J533 Drivetrain CAN databus+30 -31Convenience CAN databusK wire265_019Diagnostic connection28 Example for data exchange for diagnosisABS control unitK wireDrivetrain CANBrake light switchGateway265_077Diagnostic connectionOnboard power supply control unit with databus diagnostic interface (gateway)The following example shows the flow of information from the drivetrain CAN over the K wire. – Because of a fault in the cable connection, the brake light switch does not supply any information to the ABS control unit. – The ABS control unit is connected to the drivetrain CAN and thereupon sets a fault in its fault memory.To enable the Vehicle Diagnostic, Testing and Information System VAS 5051 to process such diagnosis data, the databus diagnostic interface in the onboard power supply control unit relays the diagnostic information from the drivetrain CAN databus over the K wire. The data are not changed as a result of this; in other words, the information content transmitted over the K wire and the CAN databus is the same.29 Special functionsSpecial functions in the event of a crashThe safety system of the Polo features automatic circuits which, in the event of a crash, contribute to minimizing the severity of an emergency situation. The following actions are set in motion:Engine control unit Onboard power supply control unit with integrated databus diagnostic interface (gateway)– – – –central locking system is unlocked interior lights are switched on hazard warning lights system is switched on fuel supply is interruptedAirbag control unitFuel pump relayConvenience system central control unitDoor control unitOperating principle If the airbags are deployed in a crash, the airbag control unit simultaneously transmits a crash signal over the drivetrain CAN. This signal causes the engine control unit to switch off the fuel supply through the fuel pump relay. The crash signal is relayed over the databus diagnostic interface (gateway) to the convenience CAN and the convenience system central control unit thereupon unlocks all the doors. In addition, the onboard power supply control unit switches on the interior lights (if the switches are in the door contact position) and also the hazard warning lights.Fuel pumpDoor control unitM265_03930 Energy saving functionsSleep mode To minimize current consumption when the ignition is switched off, the control units which are connected to the CAN databus are switched into a sleep mode. In the case of the drivetrain CAN databus, this is the normal situation after the ignition is switched off as data only require to be transmitted in the drivetrain CAN databus if the ignition is on. In the case of the convenience CAN databus, the sleep mode is activated after the ignition is switched off and provided the following conditions exist: – – – – hazard warning light system off function retention elapsed no transfer of diagnostic data exterior lights off Wake-up mode In the event that the control unit detects a wakeup command resulting from one of the actions listed below, it relays this to the other control units so that these control units are also activated. In the case of the drivetrain CAN databus, the wake-up command is always relayed after the ignition is switched on. In the case of the convenience CAN databus, the wake-up command is transmitted after the following actions: – ignition switched on – hazard warning light system active – change in status of doors, tailgate, bonnet and ignition lock – exterior lights onException: The control unit with display unit in the dash panel insert, which is connected to the drivetrain CAN databus, also requires data from the convenience CAN databus even when no supply voltage is present (ignition off). For this reason, either a direct convenience CAN connection or a cable connection (wake-up cable) to the onboard power supply control unit is required. This depends on the equipment version of the dash panel insert.Electrical circuit J285 Control unit with display unit in dash panel insert J519 Onboard power supply control unit J533 Databus diagnostic interface = CAN databus = Wake-up cableDrivetrain CAN databusJ285Convenience CAN databusJ519J533265_01731 Convenience and safety electronicsThe convenience systemis a decentralized design. It consists of a central control unit and at least 2 door control units. You can obtain further information on the interactions of the convenience system in Self-Study Programme 193. Only supplementary details are presented here.Functions of the central control unit– Central locking of rear lock – Convenience closing functions (power windows, sliding roof) – Single door opening of driver door– Anti-theft alarm system which can be deactivated only with remote control – Ultrasound interior monitoring with deactivate function – Self-diagnosis– Central locking of doors – Unlocking and locking of complete vehicle with interior push button (Lock-Unlock) – Actuation of central locking warning lamp -SAFE-Functions of the door control units– Electrically adjustable exterior mirrors with fold-in function– Power windows with excess force limiter and with gentle opening/closing to minimize noise32 Overview of convenience system (schematic diagram)Diagnostic connectionL J519 S CAN CAN T CANCoupling stationJ393 M A R B B A MDriver doorCEFront passenger doorD CAN CANFFGGK M M A A MLeft rear doorE H ERight rear doorFNJFTailgate/boot lid265_025J393 J519 A B C D E F G HConvenience system central control unit Onboard power supply control unit Door control unit Electrically adjustable rear-view mirror Mirror and heater adjustment switch Driver door operating panel Power window switch Central locking door lock Entry warning lamp Tailgate/boot lid rotary tumbler switchJ K L M N R S TTailgate push button Central locking warning lamp -SAFEInterior monitor sensor unit Interior monitor push button Alarm horn Relay for warning lights, doors Remote control Sliding roof adjustment control unit33 Convenience and safety electronicsRemote controlRemote release of tailgate/boot lid Models fitted with a remote control feature an additional push button for separate remote release of the tailgate/boot lid. If the remote release push button is pressed, only the tailgate/boot lid is unlocked. If the tailgate/ boot lid is not opened within two minutes, it is automatically relocked. This function is coded in the onboard power supply control unit (refer also to Onboard power supply control unit page 21).265_052Remote release button for tailgate/boot lidSingle door opening of driver door This function is intended for personal safety. If the remote control Unlock button is pressed briefly only once, only the driver door is unlokked. This is indicated by all the turn signal lights flashing briefly. If the Unlock button is pressed a second time, all the locks of the car are unlocked. If the car has been completely unlocked and no door or boot lid/tailgate is opened within 30 seconds, the car is locked again. This prevents the car being left unlocked unintentionally for a lengthy period. This option is coded in the convenience system central control unit in the delivery state of the vehicle in conformity with the vehicle equipment.265_066Unlock button34 Anti-theft alarm with interior monitoringThe anti-theft alarm monitors the following areas – – – – doors, bonnet, boot lid/tailgate and ignition Interior monitoring operates as an ultrasound monitoring system and is used only in combination with the antitheft alarm. This system additionally monitors the interior of the car for any unauthorized attempt to enter the car.for unauthorized opening or operation.Sensor unit265_064Alarm horn with integrated battery Convenience system central control unit Interior monitor push buttonAn audible alarm is provided by the alarm horn of the anti-theft system and a visual alarm by the turn signal lights.The system is safe against false alarm resulting from: – knocking on the car roof or against the windows, – movements of air caused by wind or vehicles passing, temperature changes such as interior of car heating up as a result of extreme sunllight penetration and – noises of any type (e.g. horns, sirens and bells).35 Convenience and safety electronicsOperating principle of interior monitor The interior monitor is switched on automatically at the same time as the anti-theft alarm system is activated. The anti-theft alarm is activated and deactivated with the remote control after the car has been locked and unlocked. The sensor unit consists of a transmitter module, a receiver module and the analysis electronics. The monitoring unit is positioned behind the front interior light in the headlining. In the armed state, the transmitter module transmits ultrasound waves and receives their echo a short time later with the aid of the receiver module. These ultrasound waves are not perceptible to the human ear. The analysis electronics detect any irregularities in this ultrasound field and triggers the alarm through the convenience system central control unit.Push button for interior monitor Sensor unit265_051The push button for the interior monitor is located in the bottom half of the left B-pillar. If the button is pressed (button lights up yellow) and the car is locked, the interior monitor is deactivated. The interior monitor is activated again automatically when the car is next closed.265_05536 Sliding/tilting roofComfort position The sliding roof features a comfort position. If the sliding roof adjustment switch in the front interior light is turned into this position, the sliding roof is not opened fully. Consequently, there is scarcely any wind noise inside the car when travelling at higher speeds with the roof set in this position.The sliding roof adjustment switch cannot be replaced separately in the event of a repair. It is then necessary to replace the complete interior light.Comfort position265_079Comfort positionThe sliding/tilting roof offers the following additional functions: – Closing the sliding/tilting roof as part of the convenience closing function by operating the central locking system – Function maintained for 10 minutes after ignition is switched off provided none of the front doors is opened – Force limit if the sliding/tilting roof is obstructed because of difficult operation or because of an obstacle during the closing operation265_08037 Dash panel insertThe dash panel insertThe following are integrated in the dash panel insert: – Control unit with display unit in dash panel insert J285 – Immobiliser control unit J362 – Speedometer – Rev counter – Fuel gauge – Coolant temperature display – Warning lamps – Multi-function display All the warning lamps feature LEDs. No provision is made for repairs. If necessary, the complete dash panel insert must be replaced. All the information relating to the monitoring functions is processed in control unit J285 and transmitted to the warning lamps which causes them to light up, flash or show a steady light. Certain visual information is acoustically reinforced by a warning buzzer.265_026If the dash panel insert is replaced, it has to be adapted to the other systems of the car. Refer to the instructions for this in the Workshop Manual.The connectors of the dash panel insert8-pin connector Link to voltage supply 32-pin connector Link to onboard power supplyWarning buzzer32-pin connector8-pin connector265_02738 Display symbolsThe number and the location of the warning lamps depend on the model and engine version. Warning lamps which are fitted only to certain models are marked with (*). The symbols are only visible when the corresponding LEDs behind them are illuminated. The ignition must be switched on for this purpose. The table presents new warning lamps which have been added in the Polo Model Year 2002.265_028Display symbolDesignationType and meaning of indicationFog lightscome on when fog lights operating; switched on by pulling out light switch as far as first detent into side light or low beam position39 Dash panel insertDisplay symbol Designation Type and meaning of indicationElectrically powered hydraulic steeringlights up for a short time after ignition switched on and goes out after engine started, lights up continuously if fault in steering system; car should be driven to nearest workshop *Engine oil level (too low)lights up yellow if engine oil level is too low; check oil level and replenish if necessary; if bonnet remains open for more than 30 seconds, oil level warning is reset; if no oil has been replenished, warning is displayed again after about 100 km *Engine oil level (engine oil level sensor faulty)flashes yellow, i.e. engine oil level sensor is faulty; audible signal sounds in addition; drive car to nearest workshop*Engine oil pressureflashes red, i.e. engine oil pressure is too low; in addition an audible signal sounds 3 times at engine speeds of more than 1500 rpm; stop; switch engine off! Check oil level and replenish if necessary; if warning lamp continues flashing although oil is at correct level - do not drive car any further!Cruise control systemlights up if cruise control system operating *Rear seat backrest locklights up for about 20 seconds when ignition switched on if backrest of rear seat is not correctly locked; lights up and remains on if backrest is unlocked when driving* * Models fitted with optional equipment 40 Display symbolDesignationType and meaning of indicationElectronic immobiliserlights up for about 3 seconds when ignition switched on; automatic scanning of data of car key performed during this time; if authorized key is detected, car can be started; an alarm activated by the anti-theft system is switched off; if a non-authorized key is detected, car cannot be started and the warning lamp switches to „continuous flashing mode“Brake pad wear indicatorlights up if minimum permissible brake pad thickness is reached; car must be driven to nearest workshop to have brake pads inspected or replaced *Washer fluid levellights up if insufficient fluid in windscreen washer reservoir; replenish windscreen washer fluid *Door openlights up if not all the doors are closed *Trailer turn signal systemlights up if turn signal system switched on when towing a trailer. If a turn signal light at trailer or car is not operating, warning lamp does not flash.* * Models fitted with optional equipment 41 LightingHeadlightsThe new headlights are designed as a twin unit and feature clear plastic lenses for the light beams. The headlight unit has two reflectors. The reflector for main beam and side light is a single chamber, while the reflector for low beam and turn signal light is split into two chambers. The bulb for the turn signal light is coloured yellow. The light beam is produced by the respective shape of the reflector chamber. The fog lights are integrated not in the headlight unit but in the bumper.Main beam (H1 bulb) Side light Low beam (H7 bulb)265_029Turn signal lightRear light unitsThe reflector is a single unit and is divided into four main chambers; the chamber for the tail light/rear fog light is once again divided internally. The upper half of the chamber includes a bulb for the tail light. The bottom half of the chamber includes a twin-filament bulb for the tail light/ rear fog light. When the lights are switched on, one filament of this twin-filament bulb is illuminated as a tail light together with the tail light in the top half of the chamber. This provides enhanced safety in the event of one of the tail lights not operating. When the rear fog light is switched on, the second filament of the twin-filament bulb is also illuminated. Reflectors are integrated in the full area of the lens of the tail light cluster.Brake lightReversing lightTail light265_030Turn signal light (yellow bulb)Tail light/ rear fog light42 Entry warning lampThe front doors are equipped with entry warning lamps. The entry warning lamps offer a clear benefit in terms of safety when using the car in flowing traffic. The entry warning lamp is switched on through the door contact switch in the lock unit in the door lock. The convenience system central control unit J393 ensures that the entry warning lamp remains on only for 10 minutes when the car is parked with the doors open. This avoids the battery being discharged.265_032265_033F220M27J560 J519 J393 + 30 J533265_034Electrical circuit (example of driver door) F220 J393 J519 J533 J560 M27 Central locking lock unit, driver side Convenience system central control unit Onboard power supply control unit Databus diagnostic interface Relay for warning lamps, doors Entry warning lamp - left doorColour coding/Legend = Input signal = Output signal = Positive = Earth = CAN databus43 Self-diagnosisControl units in the Polo with self-diagnosis capabilityControl unit in dash panel insert and immobiliser control unitRadio or radio/navigation unitABS control unit Convenience system central control unit Climatic/ CLIMAtronic control unit265_041Airbag control unitOnboard power supply control unit with databus diagnostic interface Power steering control unitEngine control unitAutomatic gearbox control unitWO R KS H O P EQUIPMENTIrDA+-VAS 5052For diagnosis please use the up-to-date workshop literature and the Vehicle Diagnostic, Testing and Information System VAS 5051 or the Vehicle Diagnostic and Service Information System VAS 5052.265_054The connection for the diagnostic units is located between the stowage compartment in the dash panel cover on the driver side.265_043265_04244 Notes45 Test your knowledgeWhich answers are correct? Sometimes only one. But perhaps also more than one – or all of them!1.The onboard power supply control unit ... A. B. C. replaces the convenience system central control unit. is the central monitoring and control unit of the onboard power supply. controls the power demand of the onboard power supply.2.The databus diagnostic interface ... A. B. C. transmits the diagnostic data of the K wire over the CAN and vice versa. monitors the function of the onboard power supply control unit. is the connection point of the CAN databus systems.3.There are two CAN databus systems in the onboard power supply operating ... A. B. C. each on their own. together through the connections of the compact connectors. together through the gateway in the onboard power supply control unit.4.The tasks of the compact connector in the bulkhead consist of ... A. B. C. connecting the „engine compartment“ and „interior“ sections of the wiring looms. facilitating service work. creating installation space.5.The code numbers are ... A. B. C. secret numbers for the operation of the immobiliser. count numbers transmitted to the control units. values for coding control units in accordance with the vehicle equipment.46 6.The drivetrain CAN databus operates with... A. B. C. a transmission rate of 500 kBit/s. a transmission rate of 100 kBit/s. a transmission rate of 50 kBit/s.7.The wake-up function is designed to ... A. B. C. wake up the driver out of the „sleep state“. wake up the control units connected to the CAN databus systems out of the „sleep state“. control the fuel pump supply.8.The entry warning lamp is switched off automatically at a certain time if a door is open ... A. B. C. by the onboard power supply control unit. by the databus diagnostic interface. by the convenience system central control unit.9.The following conditions must be met in order to create the „sleep state“ ... A. B. C. ignition „Off“. warning light system „Off“. exterior light „Off“.10.The interior monitoring system includes ... A. B. C. alarm horn. signal horn control. sensor unit.Answers: 1. B.; 2. A., C.; 3. A., C.; 4. A., B, C.; 5. C.; 6. A.; 7. B.; 8. C; 9. A., B., C.; 10. A., C. 47 Service.265For internal use only © VOLKSWAGEN AG, Wolfsburg All rights reserved. Technical data subject to change without notice 140.2810.84.20 Corresponds to technical state 10/01❀ This paper was produced fromchlorine-free chemical pulp.