TECHNICAL DOCUMENTATION
SSP 268 The 6.0 l W12 engine in the Audi A8 – Part 2

This PDF is currently unavailable.
Read document text
268Service.The 6.0 l W12 engine in the Audi A8 - Part 2 Self-study programme 268For internal use onlyContentsPage Engine, MechanicsBelt drive/ancillaries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Water-cooled alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Hydraulic/electric fan control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Hydraulic fan circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Power steering circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Hydraulic fan control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Temperature sensor for radiator fan drive circuit -G382 . . . . . . . . . . . . . . . . . 9 Electric fan control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Continued coolant circulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Engine sub-systemsInduction system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Exhaust flap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Crankcase breather system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 System layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Secondary-air system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 System layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Vacuum system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 System layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Exhaust-gas recirculation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Fuel tank breather system - activated charcoal filter (ACF) . . . . . . . . . . . . . . . . . . 25Engine managementEngine management concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 System layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Sensors/actuators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Special features of Motronic ME7.1.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Engine speed sender -G28 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Sensor design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Camshaft position senders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Sensor design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Oil temperature sender -G8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Detection of combustion missing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 CAN data exchange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Additional signals/interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46ServiceNotes on maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Workshop equipment/special tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50The self-study programme contains information on design features and functions. The self-study programme is not intended as a Workshop Manual. Values given are only intended to help explain the subject matter and relate to the software version applicable at the time of SSP compilation. Use should always be made of the latest technical publications when performing maintenance and repair work.NewAttention Note2Engine, MechanicsBelt drive/ancillariesWater pump Idler wheelsAir-conditionerAlternatorCrankshaft Tensioning roller Tandem oil pumpSSP268_0473Engine, MechanicsWater-cooled alternatorTo satisfy the power supply requirements of the Audi A8 W12, use is made of a watercooled 190 A alternator with a power output of 2660 W. Alternators generate a high level of current even at low speeds. High component temperatures occur in this operating range due to the low speeds in relation to power output. With air-cooled alternators, the cooling output is a function of speed, which results in extreme heating of the components in the event of high power output in combination with low speed. High ambient temperatures aggravate this situation. With water-cooled alternators, cooling is provided by a water jacket surrounding the stator winding and the surface of the mounting plate for rectifier diodes and regulator. The water jacket of the alternator is incorporated into the engine cooling circuit (refer to SSP 267, Page 34 onwards). This serves to guarantee constantly efficient cooling in all operating ranges, which is of particular significance in the previously critical operating range, namely high power output at low speeds. The "open" design with respect to the pulley provides an exchange of cooling air for the claw-pole rotor. The air vortex of the clawpole rotor is sufficient to achieve this. There is thus no need for a fan impeller. Permanent magnets between the rotor segments enhance the magnetic flux between claw-pole rotor and stator winding and serve to increase efficiency. For this purpose, the poles of the permanent magnets have the same polarisation as the rotor segments. The permanent magnets are relatively weak so as to minimise self-excitation and to permit regulation of the alternator voltage.SSP268_097 4SSP268_048Permanent magnets between the rotor segments enhance the magnetic flux (from the claws to the stator winding and vice versa), thus preventing stray flux between the individual poles. Water jacketFurther advantages of water-cooled alternators: – Quiet operation due to the absence of a fan impeller (no aerodynamic flow noise) – Smooth running thanks to rigid, enclosed design of alternator housing – Decrease in drive power required due to absence of fan impeller yields up to 5 % greater efficiency (as a function of speed) – Recovery of heat lost to engine cooling circuit during warm-up phase – High performance level thanks to constant cooling over entire speed range – Insusceptibility to high ambient temperaturesSSP268_0505Engine, MechanicsHydraulic/electric fan controlHeat from the engine cooling system is dissipated by way of a hydraulic fan system in combination with a 300 W electric fan. Advantages of hydraulic fan system: – High overall system performance – High efficiency even at low engine speeds – No drain on vehicle electrical system – Compact system allowing great flexibility of fitting location – Infinite output control to suit requirements The speed of the hydraulic fan basically depends on the quantity of fluid flowing through the hydraulic motor. In turn, the quantity of fluid is governed by the pump volume (pump speed) and the temperature of the hydraulic fluid. The radiator fan valve -N313 (actuated by engine control unit 1 -J623) regulates the flow of fluid to the hydraulic motor and provides infinitely variable control of the fan speed. Operation The hydraulic fan is controlled as a function of speed.The hydraulic fan system was adopted from the V8 TDI engine and adapted to match the specific features of the W12 engine (refer to SSP 226, Page 24 onwards). A new addition is the temperature sensor for the radiator fan drive circuit -G382 (refer to Page 9).Hydraulic fan circuit: Suction hose/ hydraulic motor circuit Distributor Tandem pumpReturn flow from hydraulic motorSupply/ hydraulic motor6Hydraulic motorSteering boxFluid reservoir Direction of travel Return flow from fluid cooler Supply/ steering boxTemperature sensor -G382 Return flow from hydraulic motorSupply/ hydraulic motor Return/ hydraulic motor DistributorFluid coolerSuction hose/ steering box circuitHydraulic motorSuction hose/ hydraulic motor circuit Return flow from steering box Tandem pump Radiator fan valve -N313 SSP268_077Power steering circuit: Return flow from oil cooler Fluid reservoirDistributor Fluid coolerReturn flow from steering boxSuction hose/ steering box circuitTandem pump Steering box Supply/ steering box7Engine, MechanicsHydraulic fan control On the basis of coolant temperature (-G62), ambient temperature (-G42) and vehicle speed, engine control unit 1 -J623 calculates a specified fan speed as a function of the specified coolant temperature. Further parameters for specified fan speed: – Air conditioner/compressor "ON" – Status of air-conditioner pressure switch -F129 (for further details, refer to Page 46) The radiator fan valve -N313 is actuated on a pulse-width modulated basis with a duty cycle (TVH) of between 0 and 100 %. Valve -N313 is open when deenergised. In this status, the hydraulic fan attains its maximum speed of 2800 rpm. The fluid flow is then restricted by the pressure control valve in the pump. For technical reasons the hydraulic fan is never completely shut down. Even when no cooling is required, it is actuated at a minimum speed of approx. 400 rpm.The fan speed is directly proportional to the volume (speed) of the hydraulic pump, the temperature of the hydraulic fluid and the switching status of the radiator fan valve -N313. The current value for actuation of the radiator fan valve -N313 is calculated from the pump speed (derived from engine speed), the specified fan speed and the hydraulic fluid temperature (from -G382).Pressure port/ steering boxPump section/ power steeringPump section/ hydraulic fan system Suction port/ hydraulic motorSuction port/ steering boxPump driveSSP268_028 Pressure port/ hydraulic motorRadiator fan valve -N313The hydraulic pump is of tandem design, supplying fluid pressure to the power steering and hydraulic fan.8Temperature sensor for radiator fan drive circuit -G382 The temperature sensor -G382 detects the temperature of the hydraulic fluid, which is of crucial importance to the viscosity of the fluid. The viscosity influences the speed and thus the performance of the hydraulic fan. For reasons of noise, the fan speed should not exceed approx. 2100 rpm. This speed limit is referred to in the following as "comfort speed". If the coolant temperature exceeds roughly 115 °C, the hydraulic fan operates at maximum speed regardless of the associated noise level. In view of pump losses, the following rules apply given a constant pump speed: – High hydraulic fluid temperature Lower fan speed – Low hydraulic fluid temperature Higher fan speedPrevious control method (V8 TDI engine without -G382) The temperature of the hydraulic fluid is one of the fan speed parameters. With regard to the comfort speed, this was derived to date from the ambient temperature. With allowance for production tolerances, this method of determining the temperature of the hydraulic fluid requires an appropriately large safety margin with respect to the acoustically acceptable comfort speed limit. Optimum use can therefore not be made of the comfort speed range, with the fan having to run more frequently at maximum speed.New control method (with -G382) Sensing of the hydraulic fluid temperature (-G382) adds a further crucially important parameter which considerably improves hydraulic fan control, thus permitting more precise regulation and consequently better utilisation of the comfort speed range. More efficient use is made of the available potential up to the comfort speed limit. As a result, the fan does not have to be operated as often at maximum speed with its associated high noise level.Temperature sensor for radiator fan drive circuit -G382The internal gear of the hydraulic motor simultaneously acts as fan drive gear and is driven by the regulated fluid flow.Trochoid internal gear of hydraulic motor SSP268_027 9Engine, MechanicsElectric fan control The 300 W electric fan (radiator fan -V7) – Provides back-up for the hydraulic fan system when the engine is running (irrespective of engine speed) – Ensures the necessary heat dissipation during continued coolant circulation The twin series resistor permits three speed settings. Fan run-on (fan speed 1) is activated by engine control unit 1 -J623 on the basis of the continued coolant circulation map and switched by the radiator fan run-on relay -J397. Fan speed 2 is switched by the radiator fan thermoswitch -F18 or the air-conditioner operating and display unit -E87. Fan speed 3 (max.) is switched either by the airconditioner pressure switch -F129 or, as of a coolant temperature of approx. 115 °C, by the combi processor in the dash panel insert -J218. The input signal for this is supplied by the coolant temperature sender -G2.Continued coolant circulationContinued coolant circulation is regulated by engine control unit 1 -J623 in line with a map. Both the activation condition and the continued coolant circulation time are determined from the following parameters on the basis of an arithmetic model: – Coolant temperature (from coolant temperature sender -G62) – Engine oil temperature (from oil temperature sender -G8) – Ambient temperature (from intake-air temperature sender -G42) The activation condition and continued coolant circulation period are constantly calculated from the time of starting the engine. For continued coolant circulation, the pump -V51 and radiator fan -V7 are actuated in parallel. The maximum continued coolant circulation time is limited to 10 minutes. The map-controlled engine cooling thermostat -F265 is fully actuated during continued coolant circulation.Examples of activation condition as a function of ambient and coolant temperature: – Ambient temperature Coolant temperature – Ambient temperature Coolant temperature – Ambient temperature Coolant temperature 10 °C 110 °C -10 °C 115 °C 40 °C 102 °CVehicles for countries requiring an extremely high cooling output are fitted with radiator fan 2 -V177.1030 15 XJ27130 15 XSSSJ397J101J135PF12931123 V7M4 F18t°56N3931SSP268_116F18 F129 J101 J135 J271 J397 N39 S V7Radiator fan thermoswitch Air-conditioner pressure switch Radiator fan 2nd speed relay Radiator fan 3rd speed relay Motronic current supply relay Radiator fan run-on relay Radiator fan series resistor Fuses Radiator fan1 2From engine control unit 1 -J623 From air-conditioner operating and display unit -E87 From combi processor in dash panel insert -J218 To engine control unit 1 -J623 To air-conditioner operating and display unit -E87 From air-conditioner operating and display unit -E871134 56Engine sub-systemsInduction systemThe induction system consists of a multipiece intake manifold.Infeed of activated charcoal filter and oil tank breather fumes Throttle valveAir-mass meter 2 -G246 with intake-air temperature sender 2 -G299Air cleaner box, bank 2, with secondary-air pump motor -V101, bank 1To combination valve for secondary-air system bank 112Pressure limiting valvesTo intake manifold SSP268_123Suction jet pumpBrake servo connectionAir-mass meter -G70 with intake-air temperature sender -G42To combination valve for secondary-air system bank 2 SSP268_110 Air cleaner box, bank 1, with secondary-air pump motor 2 -V189, bank 213Engine sub-systemsExhaust systemPrimary catalytic converter Cylinders 1-3 Primary catalytic converter Cylinders 10-12 Double-D pipe G39 G108 Primary catalytic converter Cylinders 4-6G285G286 G288 Decoupling elements (do not kink by more than 10° to avoid damage) G131G130Primary catalytic converter Cylinders 7-9G287Length compensation flange Main catalytic convertersTo offset production tolerances, the flange connections between the two primary catalytic converters of exhaust banks 1 and 3 and the intermediate pipe are provided with a length compensation flange. For manufacturing reasons, the clamp-type flange connection at the primary catalytic converter (exhaust bank 1/3) is additionally welded after assembly in series production. The primary catalytic converters are thus paired with the intermediate pipe. Consequently, replacement of the primary catalytic converters (exhaust bank 2/4) or intermediate pipe also involves replacing the associated primary catalytic converter (exhaust bank 1/3).Lambda probes Upstream of CAT G39 G108 G285 G286 Downstream of CAT G130 G131 G287 G28814The exhaust gas flow from three cylinders is collected in an exhaust manifold with air gap insulation, thus resulting in a total of four socalled exhaust banks (see illustration on Page 16). Each exhaust bank is assigned an underbonnet 3-way primary catalytic converter (metal-substrate catalytic converter). After passing through the primary catalytic converters, the exhaust gas flow of each exhaust bank is routed separately (in four channels) to the two decoupling elements.The four-channel design of the exhaust system until just upstream of the main catalytic converters (long separate exhaust flow routing) provides a vastly improved torque profile in the lower engine speed range. This long exhaust gas flow separation is achieved by means of an intermediate pipe (fleece-insulated) with two D-section "inliners". The further conversion of the exhaust gases takes place in the 3-way main catalytic converter (metal-substrate catalytic converter) assigned to each cylinder bank. An X-shaped pipe section causes the two exhaust gas flows to merge before entering the centre silencer. The subsequent joint routing in the centre and rear silencers produces the typical 12-cylinder exhaust noise. The right tailpipe is fitted with an electronically actuated exhaust flap.X-shaped pipe sectionRear silencerCentre silencerExhaust flap SSP268_113 Dual-flow tailpipe with noise optimisation15Engine sub-systemsAdvantages of metal-substrate over ceramicsubstrate catalytic converters: – The lower flow resistance results in a lower exhaust back pressure (enhanced power yield). – The catalytic converter response temperature is attained more quickly on account of the lower heat capacity of the metal substrate (reduced pollutant emissions). Mixture composition and emission control are monitored by way of four independent control loops using eight heated Lambda probes. Each primary catalytic converter is assigned a wide-band Lambda probe as upstream probe and a step-change probe as downstream probe. Operation of the wide-band Lambda probe is described in SSP 247 on Page 21 onwards.Cylinder bank 2 Cylinder bank 1Exhaust bank 3 Cylinders 7-9Exhaust bank 1 Cylinders 1-3Exhaust bank 4 Cylinders 10-12Exhaust bank 2 Cylinders 4-6SSP268_079To main catalytic converters16Exhaust flap The exhaust flap is switched by engine control unit 1 -J623 as a function of engine load, engine speed and vehicle speed. The exhaust flap is closed at idle and in the lower part-throttle range, thus enhancing silencer efficiency. When the above parameters exceed certain defined values, the exhaust flap is opened to reduce exhaust back pressure. This enables the comfort level to be maintained in low load ranges without the detrimental effect of increasing exhaust back pressure in higher load ranges.Operation/control of exhaust flap In deenergised and depressurised condition, the exhaust flap is kept open by way of spring force. This ensures the unimpeded discharge of exhaust gases in the event of system faults and prevents a reduction of performance and/or component damage. Actuation of the valve -N321 causes vacuum to be applied to the vacuum unit, thus closing the exhaust flap by overcoming the spring force. Switching conditions for opening of exhaust flap: Vehicle speed Engine load Engine speed 5 km/h 50 % 2500 rpmNon-return valveIntake manifoldVacuum reservoir J623 Flap open SSP268_179 Energised Deenergised Non-return valveIntake manifoldVacuum reservoir J623 Flap closed SSP268_180Atmospheric pressureVacuum 17Engine sub-systemsCrankcase breather systemSystem layoutPressure limiting valvesCylinder bank 2Cylinder bank 1Fresh airImpacterDipstickImpacter/ returnOil tankCrankcase breatherSSP268_064 18To intake manifoldSSP268_123ImpacterBreather pipeBreather pipe to pressure limiting valvesCylinder head breather SSP268_007 Oil return to oil tankThe breather fumes, consisting of blow-by gases and oil vapours, from the cylinder heads and central crankcase are collected in the oil tank, from where they are routed via pressure limiting valves into the intake manifold.An oil separator extracts the oil particles from the fumes so as to ensure that the gases entering the intake system contain as little oil as possible even at high air flow rates. The pressure limiting valves restrict the vacuum in the engine. If the vacuum in the engine exceeds a certain value, the diaphragm is pulled (overcoming the spring force) onto the connection to seal it. This prevents excessive vacuum damaging the axial oil seals.19Engine sub-systemsSecondary-air systemSystem layoutCombination valve for secondary-air system bank 2Secondary-air pump motor 2 -V189Secondary-air inlet valve 2 -N320Secondary-air pump relay 2 -J545 Energised DeenergisedVacuum reservoir 20Combination valve for secondary-air system bank 1Secondary-air inlet valve -N112Secondary-air pump motor -V101Secondary-air pump relay -J299Engine control unit 2 -J624Engine control unit 1 -J623SSP268_11121Engine sub-systemsOperation of the secondary-air system and the individual components is described in detail in SSP 217 on Page 32 onwards.Discharge of secondary air directly at exhaust valveFrom combination valve for secondary-air system Duct routing in exhaust manifold Secondary-air duct SSP268_076A special feature of the secondary-air system is that the secondary air is routed by way of ducts in the exhaust manifolds back to the secondary-air ducts in the cylinder head. The secondary-air ducts in the cylinder head route the secondary air directly behind the exhaust valves.22Vacuum systemSystem layoutCombination valve for secondary-air system Secondary-air pump motor 2 -V189 Secondary-air inlet valve 2 -N320 Combination valve for secondary-air systemSecondary-air pump motor -V101Secondary-air inlet valve -N112 Vacuum reservoirVacuum reservoir J624 Activated charcoal filter solenoid valves -N80 and -N333 Secondary-air pump relay 2 -J545 J623Non-return valve Crankcase breather fumes (from oil tank) Secondary-air pump relay -J299Activated charcoal filterFuel pressure Intake manifold regulatorTo vacuum reservoirExhaust flap 1 valve -N321Exhaust flap SSP268_160N320 N112 Non-return valve 23Engine sub-systemsExhaust-gas recirculationAs exhaust-gas recirculation is implemented by way of the valve overlap (internal EGR), it is dealt with in the Section on Camshaft timing control in SSP 267.The appropriate description can be found in SSP 267 on Page 54 onwards.SSP267_11724Fuel tank breather system activated charcoal filter (ACF)Fuel returnFuel supplyACF breatherSSP268_100Activated charcoal filter solenoid valve -N80Activated charcoal filter solenoid valve 2 -N333Activated charcoal filter in rear left wheel housingSSP268_15725Engine managementEngine management conceptEngine control unit 2 -J624 Engine control unit 1 -J623BOSCHBOSCHBOSCHBOSCHSSP268_129The engine management system for the W12 engine - Motronic ME7.1.1 - takes the form of a so-called twin control unit concept. The two control units are fully identical and each is assigned to one cylinder bank. This means that the two cylinder banks are to be viewed as separate engines. Certain sub-functions are however common to both control units: – Engine control unit 1 -J623 for cylinder bank 1 – Engine control unit 2 -J624 for cylinder bank 2 The Motronic ME7.1.1 engine management system is a more advanced version of the Motronic ME7.1, which was described in SSPs 198 and 217. Relevant information can be found as follows: – Torque-oriented engine management (SSP 198, Page 33 onwards) – Electrically operated throttle valve (electronic throttle function - SSP 198, Page 36 onwards; SSP 217, Page 42) – Sensors (SSP 198, Page 49 onwards) – Rapid starting functions (SSP 217, Page 40 onwards) – Engine run-out detection (SSP 217, Page 41)26Control unit/cylinder bank assignment identification is provided by way of so-called pin encoding in the wiring harness. To provide a clear distinction, the wiring harness to each control unit is wound with differently coloured tape. Pin encoding means that the interface pin 49 of engine control unit 1 -J623 is connected to terminal 15 and pin 49 of engine control unit 2 -J624 is connected to terminal 31. On account of the twin control unit concept attention must be paid to the following: Both control units must … … have the same software version … be matched to the cruise control system (CCS) … be matched to the immobilizer … be viewed as separate entities for selfdiagnosis … have the same encodingThe following functions are implemented solely by engine control unit 1 -J623: – Determination of specified speed values for idling speed control – Coolant temperature regulation, continued coolant circulation, actuation of continued coolant circulation pump -V51 and hydraulic fan – Provision of CAN data for drive system CAN – Actuation of fuel pump relay -J17 and Motronic current supply relay -J271 – Control of exhaust flap Processing of the following interfaces: – Brake light/pedal switches -F/-F47 (refer to SSP 198, Page 56) – Coolant temperature sender -G62 (refer to Page 32) – Cruise control system switch -E45 – AC high-pressure signal from air-conditioner pressure switch -F129 – Terminal 50 signal – Engine speed signal For further details, refer to "Additional signals/ interfaces", Page 43 onwards. The following functions are implemented solely by engine control unit 2 -J624: – Detection of combustion missing – Processing of oil temperature sender -G8 signal (refer to Page 42)K50SSP268_148Engine control unit 2 -J624Engine control unit 1 -J623Terminal 31Terminal 15 27Engine managementSystem layoutMotronic ME7.1.1 Sensors/actuatorsLambda probe/Lambda probe 2 -G39/-G108 Lambda probe/Lambda probe 2 after catalyst -G130/-G131 Drosselklappensteuereinheit J338Accelerator position/ accelerator pedal position sender -G79/-G185Air-mass meter -G70 Intake-air temperature sender -G42Engine control unit 1 -J623Cruise control system switch -E45Temperature sensor for radiator fan drive circuit -G382 Additional signalsKnock sensors 1 + 2 -G61/-G66Engine speed sender -G28Pin 49 to terminal 15Camshaft position senders -G40 (inlet) -G300 (exhaust) Throttle valve control part 2 -J544Brake light switch -F Cruise control system brake pedal switch -F47Coolant temperature senders -G2/-G62Diagnostic connectionLambda probes 3/4 -G285/-G286 Engine speed sender -G28 Lambda probe 3/ Lambda probe 4 after catalyst -G287/-G288Drive system CANAdditional signalsOil temperature sender -G8 Air-mass meter 2 -G246 Intake-air temperature 28 sender 2 -G299 Camshaft position senders -G163 (inlet) -G301 (exhaust)Knock sensors 3 +4 -G198/-G199Pin 49 to earth Engine control unit 2 -J624Throttle valve control part -J338Ignition coils with output stage -N70, 127, 291, 292, 323, 324Injectors -N30, 31, 32, 33, 83, 84Motronic current supply relay -J271Secondary-air inlet valve -N112Activated charcoal filter solenoid valve -N80Map-controlled engine cooling thermostat -F265Additional signalsExhaust flap 1 valve -N321 Camshaft adjustment valves -N205 (inlet) -N318 (exhaust)Electrohydraulic engine mounting solenoid valve, right -N145Radiator fan Radiator fan Additional coolant run-on relay valve -N313 pump relay -J496 -J397 with continued coolant circulation pump -V51 Secondary-air pump relay Fuel pump relay -J17 with -J299 with secondary-air fuel pump -G6 pump motor -V101Throttle valve control part 2 -J544Ignition coils with output stages -N325, -N326, -N327, -N328, -N329, -N330Injectors -N85, 86, 299, 300, 301, 302Secondary-air inlet valve 2 -N320SSP268_119Additional signalsActivated charcoal filter solenoid valve 2 -N333 Electrohydraulic engine mounting solenoid valve, left -N144 Secondary-air pump relay 2 -J545 with secondary-air pump motor 2 -V189Camshaft adjustment valves -N208 (inlet) -N319 (exhaust) 29Engine management30 15 XBlock diagramMotronic ME7.1.1 A E45 F F47 F265 Battery Cruise control system switch Brake light switch Cruise control system brake pedal switch Map-controlled engine cooling thermostat Coolant temperature sender Fuel pump Oil temperature sender Engine speed sender Lambda probe Inlet camshaft position sender/ cylinder bank 1 Intake-air temperature sender Knock sensor 1 Coolant temperature sender Knock sensor 2 Air-mass meter Accelerator position sender Lambda probe 2 Lambda probe after catalyst Lambda probe 2 after catalyst Inlet camshaft position sender/ cylinder bank 2 Accelerator pedal position sender 2 Throttle valve drive (electric throttle operation) Throttle valve drive angle sender 1 (electric throttle operation) Throttle valve drive angle sender 2 (electric throttle operation) Knock sensor 3 Knock sensor 4 Air-mass meter 2 Lambda probe 3 Lambda probe 4 Lambda probe 3 after catalyst Lambda probe 4 after catalyst Throttle valve drive 2 Angle sender 1 for throttle valve drive 2 Angle sender 2 for throttle valve drive 2 Intake-air temperature sender 2 G300 G301 G382 Exhaust camshaft position sender/ cylinder bank 1 Exhaust camshaft position sender/ cylinder bank 2 Temperature sensor for radiator fan drive circuit Fuel pump relay Motronic current supply relay Secondary-air pump relay Throttle valve control part Radiator fan run-on relay Additional coolant pump relay Throttle valve control part 2 Secondary-air pump relay 2 Engine control unit 1 Engine control unit 2 Brake light bulb, left Brake light bulb, right Injector, cylinder 1 Injector, cylinder 2 Injector, cylinder 3 Injector, cylinder 4 Ignition coil 1 with output stage Activated charcoal filter solenoid valve Injector, cylinder 5 Injector, cylinder 6 Injector, cylinder 7 Injector, cylinder 8 Secondary-air inlet valve Ignition coil 2 with output stage Electrohydraulic engine mounting solenoid valve, left Electrohydraulic engine mounting solenoid valve, right Camshaft adjustment valve 1 Camshaft adjustment valve 2 Ignition coil 3 with output stage Ignition coil 4 with output stage Injector, cylinder 9 Injector, cylinder 10 Injector, cylinder 11 Injector, cylinder 12 Radiator fan valve N318 N319 N320 N321 N323 N324 N325 N326 N327 N328 N329 N330 N333 Exhaust camshaft control valve 1 Exhaust camshaft control valve 2 Seconday-air inlet valve 2 Exhaust flap 1 valve Ignition coil 5 with final output stage Ignition coil 6 with final output stage Ignition coil 7 with final output stage Ignition coil 8 with final output stage Ignition coil 9 with final output stage Ignition coil 10 with final output stage Ignition coil 11 with final output stage Ignition coil 12 with final output stage Activated charcoal filter solenoid valve 2 Fuses Continued coolant circulation pump Secondary-air pump motor Secondary-air pump motor 2 Additional signals 1 2 3 Terminal 50 To radiator fan run-on relay -J397 AC high-pressure signal from air-conditioner pressure switch -F129 (high-pressure switch) AC requirement signal (from air-conditioner control unit -E87) Compressor "ON/OFF" signal Crash signal Engine speed signal CAN Low/drive CAN High/drive+ 49 31 N30N33 N83 N31 N32 N84J1715SS ESSSSS D CG2 G6 G8 G28 G39 G40 G42 G61 G62 G66 G70 G79 G108 G130 G131 G163 G185 G186 G187 G188 G198 G199 G246 G285 G286 G287 G288 G296 G297 G298 G29930J17 J271 J299 J338 J397 J496 J544 J545 J623 J624 M9 M10 N30 N31 N32 N33 N70 N80 N83 N84 N85 N86 N112 N127 N144 N145 N205 N208 N291 N292 N299 N300 N301 N302 N3134CBX A5 6 7 8 9J299 N145 N318 N205 N112 N80 N321MV101S V51 V101 V189A15C+= Input signal = Output signal = Positive supply = Earth = CAN BUSB C D E X{{Colour codeA1 0 2 2aPower supply from Fuel pump relay -J17MN70 G6 N127 N291 N2920,2aN313mLDG70/G42GPower supply from Motronic current supply relay -J271 Connections within block diagramN323 N324P Q3130 15 XJ27115SSSSS A D C CSJ338 G186 G187 G188F265 F47 FG382 t°D J397 EEJ544 G296 G297G298G198G199G8MJ496 N144 N319 N208 N320 8 9 N85MJ545 N333N302 N300N301 N86 N299MM9 V51 M10 D 31MV189 31XJ623J624+ B-+C E-+ Bλ+λ++P ZP ZN ZN Z1G66 G61 G62 G2 G40 G300 G28 G79 G185234567 N325N326N327N328N329N330mL G246/G299 G287G130G131G39G108P QB 49λ+-+-+λ+P ZP ZN ZN ZG288G285G163 G286G30131Engine managementSpecial features of Motronic ME7.1.1The Motronic ME7.1.1 is a more advanced version of the Motronic ME7.1. Important new features: – Greater computer capacity on account of new computer-bound sub-functions – Extension of control unit activities after switching off ignition with the aid of main relay concept – Infinitely variable adjustment of inlet and exhaust camshafts (refer to SSP 267, Page 59 onwards) – Designed to suit new wide-band Lambda probes upstream of catalytic converter (refer to Page 14) – Designed for coolant temperature regulation – Enhanced evaluation of signals from coolant temperature sender -G62 – Management of additional and new CAN messages (refer to Page 44)-G62 evaluation Precise determination of the coolant temperature in the lower operating temperature range is required for cold starting and subsequent warm-up. Coolant temperature regulation demands exact recognition of the coolant temperature in the upper operating temperature range.3Switching to the evaluation circuit for the upper temperature range takes place as of a coolant temperature of approx. 50 °C.RNTC [W]Precision sensing of the coolant temperature over a broad temperature range must therefore be of a very high standard. For physical reasons, the characteristic curve of -G62 (NTC sender) is highly degressive over the temperature range to be recorded (approx. -30 °C to + 120 °C). At the same time the coefficient of resistance ranges from approx. 25 000 ohms to approx. 115 ohms. The change in resistance per °K thus varies considerably at low and high temperatures. To achieve the required level of accuracy for both temperature ranges, the ME7.1.1 has a separate evaluation circuit for each one.210 4 8 6 4 3 210 3 8 6 4 3 2 10 2 8 -30 -20 0 20 40 60 80 100 12032SSP268_190u [°C]Main relay concept To date, the power supply for the sensors and actuators was provided largely via the fuel pump relay -J17. A new addition is the Motronic current supply relay -J271 (main relay). As with the fuel pump relay -J17, the Motronic current supply relay -J271 is actuated by engine control unit 1. Thanks to the Motronic current supply relay -J271, the engine control units can still implement certain functions after the engine has been switched off (ignition OFF). The following sensors/actuators are supplied with power by the Motronic current supply relay -J271: – – – – – – – – Engine control unit 1 Engine control unit 2 Ignition coils of cylinder bank 1 Ignition coils of cylinder bank 2 Camshaft adjustment valves Engine mounting solenoid valves Radiator fan valve -N313 Additional coolant pump relay -J496 (continued coolant circulation pump -V51) – Radiator fan run-on relay -J397 (radiator fan -V7) – Map-controlled engine cooling thermostat -F265After switching off the ignition, the ignition coils continue to be actuated until the engine stops in order to ensure ignition of the fuel already injected. This means that no unburned fuel/air mixture reaches the exhaust system, thus reducing the level of exhaust emissions. The camshaft adjustment valves also remain actuated until the engine stops following ignition switch-off to ensure that the camshafts are kept in the appropriate position until the engine has stopped. The engine mounting solenoid valves are actuated to provide smooth, vibration-free engine shutoff. The solenoid valve for the hydraulic fan is actuated to prevent brief fan speed increase.Refer to block diagram on Page 30.As engine control unit 1 is responsible for control of the entire continued coolant circulation process, it must be possible to actuate the control elements (relay -J496, relay -J397 and thermostat -F265).33Engine managementEngine speed sender -G28 The engine speed sender supplies the most important engine management input signal. The engine will not run in the event of -G28 failure. The absence of a signal from -G28 is recognised by the self-diagnosis function. In view of the twin control unit concept and the high dynamic requirements (real time) for the engine speed signal, the engine speed sender -G28 is connected directly to both engine control units. The sensor used is a so-called "differential Hall sensor" with integrated permanent magnet which is suitable for scanning ferromagnetic sender wheels. Previous knowledge of the way in which Hall sensors work is required for understanding of this Section. Further details can be found in pertinent motor vehicle engineering reference works.SSP268_164-G28J623 J624Engine speed sender-G40Inlet camshaft position sender/cylinder bank 1 Inlet camshaft position sender/cylinder bank 2 Exhaust camshaft position sender/cylinder bank 1 Exhaust camshaft position sender/cylinder bank 2-G163+ + + + +G40G300G28G163 G301-G30031SSP268_159-G30134Engine speed sender -G28SSP268_167Evaluation electronicsPermanent magnet N S Hall element 1 Hall element 2Rotor (sender wheel)Magnetic lines of forceSSP268_168 35Engine managementSensor design Signals are generated by two Hall elements arranged behind one another with respect to the sender wheel. Located above the two Hall elements and integrated into the sensor is a permanent magnet, the field of which acts on the Hall elements. The integrated evaluation electronics - also referred to as Hall IC evaluate the Hall voltages of the two Hall elements and generate the sensor output signal.HE1Output signalS HE2Hall elements react to changes in the magnetic field. The sender wheel takes the form of a rotor and influences both the field strength of the permanent magnet and the Hall voltages of the two Hall elements. If the rotor (ferrous metal) is located directly beneath the Hall elements, the ferrous metal will intensify the magnetic field in the area of the Hall elements. The Hall voltage of the two Hall elements increases with increasing magnetic field strength. The fact that the two Hall elements are arranged behind one another leads to differing Hall voltage levels at the Hall elements at the transition from rotor to gap (or vice versa). The resultant difference between and the magnitude of the Hall voltages are used for evaluation and generation of the output signal.N SHall voltage UHENUHE1UHE2SSP268_194UHE1N SHall voltage UHE UHE2SSP268_195UHE1 Hall voltage UHEUHE2IC stands for "integrated circuit" and refers to an integrated semi-conductor circuit.SSP268_19636Camshaft position senders In addition to the main purpose of defining the camshaft position with respect to the position of the crankshaft, one camshaft position sender each is required for inlet and exhaust camshaft adjustment. Sender signals are required for the following functions: – -G28 and -G40 Synchronisation of bank 1 (with cylinder 1/ cylinder 6) for knock control and sequential injection -G300 is responsible for synchronisation in the event of failure of -G40. – -G28 and -G163 Synchronisation of bank 2 (with cylinder 12/cylinder 7) for knock control and sequential injection -G301 is responsible for synchronisation in the event of failure of -G163. Bank 2 synchronisation is offset by 60° with respect to bank 1. The pin encoding ensures that allowance is made for this in the software.– -G28 and -G40/300 Control and monitoring of camshaft adjustment for cylinder bank 1 – -G28 and -G163/301 Control and monitoring of camshaft adjustment for cylinder bank 2 There is no camshaft timing control function if one of the camshaft position senders is defective. In the event of failure of both the camshaft position senders of one bank, engine starting is enabled by the engine run-out detection function. Adaption of sender signals -G40/-G300/-G163 and -G301 provides more accurate determination of the camshaft basic positions (for more information, refer to SSP 267 - Part 1, Section on "Camshaft timing control", Page 54).Cylinder bank 2Cylinder bank 1Hall sender 4 -G301Hall sender 2 -G163SSP268_147Hall sender -G40Hall sender 3 -G300 37Engine managementSensor design As already described for the engine speed sender -G28, the camshaft position sender is also a so-called "differential Hall sensor". The camshaft position senders employ a twotrack rapid start sender wheel made of ferrous metal. The sender wheel has two broad and two narrow rotors/gaps. This design, featuring different rotor widths, enables the signal profile of -G40/-G163 together with that of sender -G28 to be used for more rapid determination of camshaft adjustment with respect to the crankshaft.Track 1Track 2Camshaft position senderHall element 2 Hall element 1 SSP268_149 Permanent magnet38A further feature of the sender wheel design is that two "tracks" are in adjacent, mutually inverted arrangement. The "two-track system" ensures more precise generation of the sensor signal. The signals are generated by two Hall elements HE1 and HE2 arranged next to one another with respect to the sender wheel. One track is assigned to each of the Hall elements. Located above the two Hall elements and integrated into the sensor is a permanent magnet, the field of which acts on the Hall elements. The integrated evaluation electronics - also referred to as Hall IC evaluate the Hall voltages of the two Hall elements and generate the sensor output signal.Hall elements react to changes in the magnetic field. The sender wheel is of twotrack design and influences the strength of the permanent magnet. When the rotor (ferrous metal) of track 1 is located directly beneath HE1, there is a gap under HE2. The ferrous metal intensifies the magnetic field in the area of HE1 and the Hall voltage of HE1 increases with respect to HE2. The difference between HE1 and HE2 and the magnitude of the two Hall voltages are used for evaluation and generation of the output signal.Hall element 2 Hall element 1Track 2Track 1SSP268_150S NSSP268_151 SSP268_193 Permanent magnet39Engine managementEngine speed sender -G28Software reference mark660°720° 0°60°120°180°240°ITDC 9ITDC 1ITDC 12ITDC 5ITDC 8ITDC 378° 138°6° CS 114° CS/Inlet in reference position (retard)Inlet camshaft -G40/-G16352° maximum advance92° CS/Exhaust in reference position (retard)Exhaust camshaft -G300/-G30122° maximum advance40° CS 40° CS140° CS 40° CSThe signal profiles of the camshaft position senders are identical for both inlet and exhaust camshafts of cylinder banks 1 and 2 (same distance from software reference mark). Basic synchronisation of the first ignition TDC (ITDC) of cylinder bank 1 (cylinder 1) takes place 78° after the software reference mark.40On account of the special features of the engine mechanical and management systems, basic synchronisation of the first ignition TDC (ITDC) of cylinder bank 2 (cylinder 12) takes place 138° after the software reference mark. Allowance is made for this in the control unit and it is specified by the pin encoding.Software reference mark300°360°420°480°540°600°ITDC 10ITDC 6ITDC 7ITDC 2ITDC 11ITDC 4140° CS 140° CS40° CSSSP268_085Use is made as engine speed sender of a Hall sensor. The software reference mark is the 2nd trailing edge after the gap (60-2 system).The camshafts are in "retard" position if the camshaft adjustment valves are deenergised when the engine is running. If there is no or only insufficient oil pressure, the camshafts are also set to retard position on account of the chain pull.41Engine managementOil temperature sender -G8The signal of the oil temperature sender -G8 is evaluated by engine control unit 2 -J624 and transmitted by way of CAN data transfer to engine control unit 1 -J623. It is used for calculating the specified coolant temperature and the continued coolant circulation time. To prevent overheating of the engine, mandatory change-up from 4th to 5th gear is implemented on exceeding an engine oil temperature of approx. 135 °C. The decrease in engine speed counteracts a further increase in engine oil temperature. The mandatory change-up described above also takes place on exceeding a coolant temperature of approx. 120 °C.Oil tank Oil temperature sender -G8Engine control unit 2 -J624Automatic gearbox control unit -J217CANEngine control unit 1 -J623SSP268_145Detection of combustion missingPlease refer to the notes given in the "Service" Section on Page 48.42Notes43Engine managementCAN data exchangeThe twin control unit concept has resulted in the addition of new CAN messages, via which the two engine control units exchange data. Engine control unit 1 transmits information to engine control unit 2 by way of so-called "master-slave messages". So-called "slave-master messages" provide engine control unit 1 with data from engine control unit 2. Although these messages are transmitted by means of the general drive system CAN, they are only used for the exchange of data between the two engine control units.Engine control unit 1 (master control unit) – – – – – – – – – – – – – – – – – – – – – – – – Intake-air temperature Brake light switch1 Brake pedal switch Throttle valve angle Electronic throttle warning lamp/ info Driver input torque Fault status1 Accelerator pedal position1 CCS switch positions CCS specified speed Altitude information Compressor switch-off Compressor ON/OFF (feedback from bidirectional interface) Fuel consumption Coolant temperature1 Idling speed recognition Engine shutoff position2 Engine speed ACTUAL engine torques Emergency running programs (self-diagnosis information) -G8 oil temperature warning Vmax limit active2 Immobilizer Crash signal2Engine control unit 2 can only transmit by way of slave-master messages. Although engine control unit 2 can transmit data to engine control unit 1 and the dash panel insert (immobilizer), it is otherwise only designed to receive data.Data transmitted by the engine control units Data received and evaluated by the engine control unitsEngine control unit 2 (slave control unit)1These data are additionally transmitted by way of masterslave messages These data are only transmitted by way of master-slave messages2– – – – – –EPC fault lamp request3 OBD fault lamp request3 Misfiring detection3 Fault status3 Oil temperature (from -G8)3 Immobilizer33These data are only transmitted by way of slave-master messages44Gearbox control unit – Torque gradient limitation (converter/gearbox protection) – Idle regulation adaption release – Compressor switch-off – Specified idling speed – Current gear/target gear – SPECIFIED engine torque – Emergency running programs (selfdiagnosis information) – Gearshift active/not active – Selector lever position – Torque converter clutch statusESP/ABS control unit – – – – – TCS request SPECIFIED TCS intervention torque Brake pedal status ESP intervention Overrun torque limiting function request – Overrun torque limiting function intervention torqueDrive system CAN HighDrive system CAN LowDash panel insert – – – – Self-diagnosis information Vehicle speed Coolant temperature Immobilizer (from both engine control units)Steering angle sensor – Steering wheel angle (used for idling speed pilot control and engine torque calculation on the basis of power steering power requirement)45Engine managementAdditional signals/interfacesIn addition to CAN BUS data exchange, the following signals are relayed via separate interfaces. Pin 42 Pin 67 Pin 41 Pin 40 Pin 54 Pin 37 Pin 49 Terminal 50 Crash signal AC compressor signal ON/OFF AC requirement signal Air-conditioner high-pressure switch signal Engine speed signal Pin encoding of control units + to pin 49 = engine control unit 1 - to pin 49 = engine control unit 2 K-wire/diagnosis Interfaces - cruise control system, refer to Page 47 ECU* 1 only ECU 1 and ECU 2 ECU 1 and ECU 2 ECU 1 and ECU 2 ECU 1 only ECU 1 onlyPin 43 Pin XXECU 1 and ECU 2 ECU 1 only* ECU = Engine control unitTerminal 50 signal The engine run-out detection function (refer to SSP 217, Page 41) can recognise "reversing" in the course of the engine shutoff process. As reversing of the engine can be ruled out on starting, the terminal 50 information (starter operated) is used for checking the plausibility of and evaluating the reversing detection function. Air-conditioner compressor ON/OFF signal For a detailed description, refer to SSP 198, Page 59. The compressor ON signal is also used as a source of information for calculating the speed of the hydraulic fan. Air-conditioner high-pressure switch signal The signal from the air-conditioner pressure switch -F129 (high pressure) provides information for actuating the hydraulic fan (refer to Page 8 onwards). When the highpressure switch is closed (approx. 16 bar), both maximum electric fan speed and maximum hydraulic fan actuation are set.Crash signal For a detailed description, refer to SSP 217, Page 47. Although ECU 1 switches the fuel pump, the crash signal is also transmitted to ECU 2. In addition to powering the fuel pump, the fuel pump relay is also responsible for supplying voltage to other actuators of both ECUs (refer to block diagram). The crash signal in ECU 2 suppresses unwanted entries in the fault memory such as would be caused by deactivation of the fuel pump. As of software version 0004, the crash signal is transmitted by means of a master-slave message. The pin 67 interface is no longer evaluated. To avoid unnecessary expense, no modifications have been made to the wiring harness (wiring to pin 67 interface still exists).46Air-conditioner requirement signal For a detailed description, refer to SSP 217, Page 48.Engine speed signal For a detailed description, refer to SSP 198, Page 60. Numerous control units require engine speed information for calculation purposes. In the majority of cases, the engine speed transmitted by way of the CAN message suffices.12a 0The engine speed is one of the most important information parameters for gearbox control, with a high standard of resolution and transmission speed being required. The output signal (square-wave signal) generated by engine control unit 1 satisfies these requirements.Set/ decelerate SSP268_189Cruise control system (CCS) interfaces For a detailed description, refer to SSP 198, Page 61. Pin 38 ON/OFF with erasing of memory (master switch) Pin 57 Set/decelerate Pin 75 Reactivate/accelerate Pin 76 OFF without erasing of memoryFIXAC TIVONOFFJ6235738767515Switch position 0 1 2 2a ONFunction3 4 6 1 2 51 0 2 2a 0,2aReactivation Accelerate/set OFF - without erasing of memory OFF - with erasing of memorySSP268_19147ServiceNotes on maintenanceA few special points have to be noted as regards handling of diagnostic testers and the self-diagnosis function on account of the twin control unit concept. As regards self-diagnosis, the two control units are basically to be viewed as separate entities (does not apply to combustion missing detection). The self-diagnosis functions are implemented in the control unit to which the components are connected (with the exception of combustion missing detection). The readiness code must be set, read out and reset separately for each control unit (e.g. by starting "short trip" test sequence with diagnostic tester). Erasing the fault memory sets the readiness code automatically in the appropriate control unit. The combustion missing detection function is only activated in engine control unit 2 -J624, which is thus responsible for both cylinder banks. Combustion missing affecting cylinder bank 1 can only be read out in engine control unit 2. Separate address words are required for entry into self-diagnosis function: Address word 01 Engine control unit 1 -J623 Cylinder bank 1 (exhaust banks 1 and 2) Address word 11 Engine control unit 2 -J624 Cylinder bank 2 (exhaust banks 3 and 4)Further information on the twin control unit concept can be found on Page 26 onwards.If a fault has been stored in engine control unit 2, the fault "Please read out fault memory of engine control unit 2" will be stored in engine control unit 1. This fault message can only be erased when there is no fault entry stored in engine control unit 2.For more details of Euro On-Board Diagnosis (EOBD) and readiness code, refer to SSP 231.Both control units must … … have the same software version … be matched to the cruise control system (CCS) … be matched to the immobilizer … be viewed as separate entities for self-diagnosis … have the same encodingFor defined fault-finding, the Lambda control can be deactivated under "Basic setting" on selecting display group 99/ reactivated under "Reading measured value block".48Engine oil change In view of the dry sump lubrication, it is always necessary to open both oil drain plugs (sump and oil tank) to drain off the engine oil. The use of an oil extractor is not possible with the W12 engine. The W12 engine is only to be filled with LongLife engine oil as per VW Standard 50301. The oil filler neck leads into the crankcase breather pipe from the cylinder heads to the oil tank. The procedure for checking the oil level is described in SSP 267 - Part 1, Page 30 onwards.Oil drain plug at oil filter Oil drain plug Oil drain plugPlease also heed the relevant additional information given in the Maintenance manual.SSP268_165Crankcase breather pipeDipstickOil filler neckOil tankSSP268_176 49ServiceWorkshop equipment/ special toolsListed in the following are the new items of workshop equipment and special tools designed for the W12 engine.VAS 6100 Workshop crane With a loadbearing capacity of 1200 kg, the workshop crane VAS 6100 is designed to handle the new large-volume engines (e.g. V8 TDI, W12) as well as future developments. Extension VAS 6101 (load bearing capacity 300 kg) is available as an option.SSP268_186VAS 6095 Engine and gearbox assembly mount In addition to the generously designed loadbearing capacity of 600 kg, VAS 6095 offers two major new features. Unit mounting with the aid of universally adjustable clamps in combination with the locating pins provides ease of access to the back of the engine (e.g. when working on timing mechanism). Work is facilitated by being able to hydraulically adjust the height of the unit by approx. 200 mm. The tilt mechanism enables the unit to be easily moved into any angular position required. The mechanism is self-locking so that there is no need for separate fixing. The integrated storage facilities and sliding drip tray for collecting fluids round off the practical design of this item. VAS 6095 is compatible with existing engine and gearbox supports.Locating pin SSP268_182 SSP268_18450Unit assembly trolley Still at the development stage is a unit assembly trolley for simple and reliable performance of all engine and gearbox preassembly work. The work table is in two sections to facilitate separation and joining of engine and gearbox. The unit assembly trolley will be universally applicable and is expected to be available in the 1st quarter of 2002.SSP268_185V.A.G 1342/15 Oil pressure test adapter with V.A.G 1342/16 Oil pressure test pipe sectionClampsSSP268_187 SSP268_181 51All rights reserved. Subject to technical modification. AUDI AG Department I/VK-35 D-85045 Ingolstadt Fax 0841/89-36367 140.2810.87.20 Technical status as at 11/01 Printed in Germany268