TECHNICAL DOCUMENTATION
SSP 272 The Phaeton Onboard Power Supply

This PDF is currently unavailable.
Read document text
Service.Self-Study Programme 272The Phaeton Onboard Power SupplyDesign and FunctionThe onboard power supply of vehicles in the early 1950s consisted of approx. 30 m of cables, some switches, lights and the ignition system. The further development of motor vehicles required a constant increase in the number of electrical as well as electronic components. In today's luxury performance class vehicles, the length of cable, despite networking, is approx. 3000 m, branching into approx. 1500 individual cables.Networking connects control units with one another via databus lines. In this way, various signals can be transmitted digitally from one control unit to another. This takes place via two databus lines and eliminates the need for a separate cable for each individual signal. This Self-Study Programme covers the design and function of the onboard power supply, that is, the power and data management of the Phaeton. It describes new control units that control and regulate the power supply. It also describes, for example, the networking of the lighting control system as well as the CAN bus topology.S272_073NEWImportant NoteThe self-study programme involves the design and function of new developments! The contents are not updated.Please always refer to the relevant Service Literature for all inspection, adjustment and repair instructions.2Table of contentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Electrics boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Energy management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Onboard supply power management . . . . . . . . . . . . . . . . 22Networked functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Control unit for windscreen heating . . . . . . . . . . . . . . . . . 39Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Dash panel insert. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Analogue clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Test your knowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 623IntroductionFitting locations in the onboard power supplyThe onboard power supply has a decentral design. The electrical components are placed at various fitting locations in the vehicle. The following overview shows the fitting locations of the fuse boxes and coupling stations.Coupling station, right and left B pillarElectronics box, front left footwell on passenger's sideElectronics box in right plenum chamberVehicle interior coupling stationCoupling station in front of e plenum chamber in engine compartmentFuse box on left under the dash panel4Back-up fuse box on left of bootElectronics box on left of bootCoupling station, right and left C pillarsThermo-fuse box in front left footwellCoupling station, right and left A pillarsS272_0095IntroductionCable routingThe main wiring harness runs from the battery in the boot on the driver's side to the connection points. In the case of vehicles with a two-battery onboard power supply, the starter motor is supplied via a separate wiring harness on the right-hand side. For protection, the wiring harnesses are laid in the floorpan area in cable ducts.Onboard power supply battery Electronics box in the left of bootConnection point, rear bumperConnection point, trailer towbarConnection point, control units under rear shelfStarter batteryCoupling station, right and left C pillars Main wiring harness Engine wiring harness Gearbox wiring harness6Coupling station, left B pillarFuse box on left under dash panel Thermo-fuse box in left footwellFront information display and operating unit Connection point for control unit for anti-lock braking system/ Electronic Stability ProgrammeConnection point, control unit for driver's seatCoupling station, left A pillarCoupling station in front of plenum chamber in engine compartment Connection point, headlights, additional heatingConnection point, front bumperConnection point, headlightsElectronics box in Connection point, right plenum chamber Coupling station, control unit for right A pillar front passenger's seat Connection points, dash panel insert and vehicle interior Coupling station, Electronics box in right B pillar front right footwellControl unit for engine electronics Control unit for gearbox electronics Connection point, engine compartmentS272_0517IntroductionEarth pointsSpecially selected locations in the vehicle serve as Earth points, as they are essential on modern vehicles with a large number of high-quality electronic control units. The electronics are dependent on equalised earth potential to be able to work faultlessly. Randomly selected Earth points can lead to different earth potentials and may cause malfunctions (e.g. compensating currents).Earth point, onboard power supply control unitEarth points, air conditioning system/DSP Earth points, right engine bulkheadEarth points, right engine compartmentEarth points at front right, near hornEarth points Engine compartment, leftEarth points, left engine bulkhead Earth point, left A pillar Earth point, airbag control unit Earth points, driver's seat8Earth points, B pillar under front passenger's seat Earth points, control unit for rear seats and rear right and left doors Earth points near left of rear window Earth points, starter batteryEarth points, aerials, rear roof cross-member under trimEarth points, tail light on right and left-hand sideEarth point, onboard power supply batteryEarth point, earth plate in left of bootEarth points, rear centre tunnel under bench seatEarth points near right of rear windowS272_0109Electrics boxesBack-up fuse box The back-up fuse box is located in the boot on the left. It contains the main fuses of the onboard power supply. Moreover, the connection leads for the onboard power supply battery, the control unit for the windscreen heater (DC/DC converter), the rear and front electronics boxes, the alternator lead as well as the measurement lead for the onboard voltage come from this fuse box.Terminal 30 spare unassigned Supply, front electronics box Alternator lead 150 A Terminal 30 100 A terminal Connection, control unit for windscreen heater100 A Terminal 30Supply of rear electronics box and measurement Onboard power lead to onboard power supply supply battery control unitS272_069Rear electronics box The electronics box in the rear left of the boot contains: - the switch-over relay for the starter battery (100), - the switch-over relay for the onboard power supply battery (432), - the fuel pump relay 1 (404), - the fuel pump relay 2 (404), - the relay for Terminal 50 (433), - the relay 1 for the rear window heater (100), - the relay 2 for the rear window heater (104), - the relay for air suspension (214) and - the relay for the tank filler flap opening (404)S272_070The relays fitted depend on the vehicle type. The current list of fitted relays is contained on the valid current flow diagram.10Electronics box, plenum chamber Components - Smoothing capacitor for onboard power supply voltage - Main relays 1 and 2 (53 and 100) - Terminal 75 relay (100) - Terminal 15 relay (433) - Secondary air pump relays 1 and 2 (100) as well as - Power supply relay for Motronic (167) are located in the electronics box in the front plenum chamber.CapacitorS272_071Thermo-fuse box The thermo-fuse box in the front left footwell contains the thermo-fuses: left window regulator right window regulator driver's seat control unit front passenger's seat control unit rear compartment seat control unit rear left PTC heating rear right PTC heating 30 A 30 A 30 A 30 A 30 A 30 A 30 AControl unit for entry and start authorisationThermofusesS272_077The thermo-fuses fitted depend on the vehicle type. The current list of fitted thermo-fuses are contained on the valid current flow diagram.11Electrics boxesRelay holder, right footwell The relay holder is located in the footwell on the front passenger's side. It contains the: water pump relay (404) vacuum pump relay (404) relay for heated wiper park position (404) relay for enable seat heating (404) sunroof relay (79) terminal 15SV relay (100) headlight washer system relay (53) relay for control unit for Servotronic (631) relay for airbag warning lamp (464)S272_08512Power managementIn order to ensure sufficient power supply of the electrical equipment and the starter motor, a - one-battery onboard power supply as well as a - two-battery onboard power supply are used.Engine V6 V8 W12 V10 TDI Onboard power supply battery 75 Ah/420 A* 75 Ah/420 A* 85 Ah/480 A 85 Ah/480 A*currently still 85 Ah/450 A The 75 Ah/420 A battery will be deployed later.Starter battery 61 Ah/330 A** 61 Ah/330 A** 61 Ah/330 A 85 Ah/480 A**optionalIn case of vehicles with one-battery onboard power supplies, it ensures the supply of electrical energy.Back-up fuse boxBatteryS272_013Vehicles with two-battery onboard power supplies have a starter battery and an onboard power supply battery. In normal operation, the starter battery supplies the starter motor during the starting cycle and the onboard power supply battery supplies the electrical equipment. If one of the batteries does not have sufficient power, it is supported by the other. Support is controlled by the control unit for battery monitoring.Relay for parallel switching of batteriesBack-up fuse boxControl unit for battery monitoringOnboard power supply batteryStarter batteryS272_01213Energy managementTo ensure the power supply for the electrical equipment on the W12 and V10 TDI, the twobattery onboard power supply is used; for all other versions, it is available as an option. Components● ● ● ● ●Functional description Normally, the starter battery supplies the starting circuit of the engine. The onboard power supply battery supplies the 12-volt onboard power supply; in the case of a cold start, it is supported by the starter battery. The circuit of the starter motor and onboard power supply electrical circuit are controlled by the control unit for battery monitoring (J367). This controls the charge of the starter battery and safely ensures supply of the electrical equipment required to start the car.● ●Starter battery Onboard power supply battery Relay for parallel switching of batteries switch-over relay for starter battery switch-over relay for onboard power supply battery Control unit for battery monitoring Temperature sensor for starter batteryA1 A4 A14 A15T. 50 Key-In Terminal 15 Emergency modeA17 T. 30 A18 T.l 15SVData transfer via CAN bus e.g. from control unit for entry and start authorisation Starter motorSwitch-over relay BTerminal 30SVSwitch-over relay SRelay for parallel switchingTerminal 30Starter batterySupplyControl unit for battery monitoring (J367) on left of bootOnboard power supply batteryS272_072Temperature sensor14Starting modesIn order to ensure sufficient power supply to both electrical circuits, different operating modes are implemented by the control unit for battery monitoring. Electrical equipment required to start the car:● ● ● ● ●Normal startThe onboard power supply and starter battery are charged. The starter and onboard power supply electrical circuits are separate. The control unit for battery monitoring is activated by the control unit for entry and start authorisation (J 518) with the signals 'Ignition key in the ignition lock' (Key-In) 'Ignition switched on' (Terminal 15) and the start signal (Terminal 50). The switch-over relay onboard power supply battery (relay B) is closed; the electrical equipment required for starting is supplied via the onboard power supply battery. The starter battery supplies the starter motor.Engine control unit Fuel pump Control unit for entry and start authorisation Dash panel insert Airbag control unit (for safety reasons)Schematic diagramTerminal 50 Terminal 30SV Terminal 15SV Control unit for entry and start authorisation Relay SStarter batteryTemperature sensor Control unit for battery monitoring Relay B Relay LTerminal 15 Terminal 30Supply of the remaining electrical equipment via onboard power supply batteryRelay S = Relay B = Relay L = SV =switch-over relay for starter battery (J580) switch-over relay for onboard power supply battery (J579) relay for parallel switching of batteries (J581) electrical equipment required for startingOnboard power supply batteryS272_01915Power managementCold startIn addition to the input signals of the normal start, the battery temperature as well as the coolant temperature transmitted via the CAN bus are taken into account. The switch-over relay onboard power supply battery is closed; the control unit for battery monitoring activates the relay for parallel switching. Activation closes the relay for parallel switching and both batteries are switched in parallel. Parallel switching is temperature-dependent: - in the case of petrol engines -10°C and - in the case of V10 TDI 0°C.Schematic diagramTerminal 50 Terminal 30SV Terminal 15SV Control unit for entry and start authorisation Control unit for battery monitoring Relay B Relay SStarter batteryTemperature sensor Relay LTerminal 15 Terminal 30Relay S = Relay B = Relay L = SV =switch-over relay for starter battery (J580) switch-over relay for onboard power supply battery (J579) relay for parallel switching of batteries (J581) electrical equipment required for startingOnboard power supply batteryS272_02016The starting cycle in the case of discharged onboard power supply batteryWith Terminal 15SV switched on, the 'Emergency start' mode is sent via the CAN bus and the PIN 'Emergency operation' if the voltage of the onboard power supply battery is less than 11 V. Terminal 30SV is connected via the switch-over relay starter battery to the starter battery as soon as the ignition key is inserted in the ignition lock. When the ignition is turned on, the Drive Train CAN bus goes to partial operation. Only control units required for starting take part in the communication. After the engine starts, heating equipment involved in the convenience system is switched off for two to five minutes. The 'Emergency operation' mode is cancelled approx. two seconds after the system detects that the engine is running. Until there is sufficient charge voltage in the onboard power supply battery, the onboard power supply is supplied from the starter battery by means of parallel switching via the relay for parallel switching. In the case of diesel engines, the connection to the starter battery is made when Terminal15SV it is switched to enable the glow phase.Schematic diagramTerminal 50 Terminal 30SV Terminal 15SV Control unit for entry and start authorisation Relay SStarter batteryTemperature sensor Relay LTerminal 15 Terminal 30Relay BControl unit for battery monitoringRelay S = Relay B = Relay L = SV =switch-over relay for starter battery (J580) switch-over relay for onboard power supply battery (J579) relay for parallel switching of batteries (J581) electrical equipment required for startingOnboard power supply batteryS272_02117Energy managementStarting cycle in the case of discharged starter batteryThe 'Emergency start' mode is sent via the CAN bus and the PIN 'Emergency operation'. Terminal 30SV remains connected to the onboard power supply battery via the switch-over relay for onboard power supply battery. Both batteries are switched in parallel via the relay for parallel switching when the start (Terminal 50) is initiated.Schematic diagramRelay SStarter batteryTerminal 50 Terminal 30SV Terminal 15SV Control unit for entry and start authorisationTemperature sensor Control unit for battery monitoring Relay B Relay LTerminal 15 Terminal 30Relay S = Relay B = Relay L = SV =switch-over relay for starter battery (J580) switch-over relay for onboard power supply battery (J579) relay for parallel switching of batteries (J581) electrical equipment required for startingOnboard power supply batteryS272_02218Monitoring after a crash eventIn the case of a crash event, the control unit for battery monitoring receives a crash signal via the CAN bus. This cancels the charge operation of the starter battery. This signal remains stored until it is reset by the VAS 5051 Diagnostic Testing and Information System. Every time the ignition is switched on, the lead to the starter motor is tested for short circuits. If a short circuit is detected, it prevents a starting cycle from initiating.Schematic diagramRelay S Control unit for battery monitoringStarter batteryTerminal 50 Terminal 30SV Terminal 15SV Control unit for entry and start authorisationTemperature sensor Relay L Terminal 15 Terminal 30 Relay BCrash signal via CAN busRelay S = Relay B = Relay L = SV =switch-over relay for starter battery (J580) switch-over relay for onboard power supply battery (J579) relay for parallel switching of batteries (J581) electrical equipment required for startingOnboard power supply batteryS272_068If the 'Key IN' is not present and the onboard power supply battery is discharged, no start is possible. The VAS 5051 Diagnostic Testing And Information System can be used to diagnose the control unit for battery monitoring.19Energy managementAlternatorA liquid-cooled alternator with 190 Amperes is fitted. Its maximum current in the short term can be up to 300 Amperes. The alternator contains six instead of three stator windings, which are excited via a winding in the rotor. The drive on the V10 TDI is via an internal shaft and a gear.S272_025ControlLegend C E Terminal B+ Terminal DF Terminal L -Liquid Exit Terminal L Terminal DF EntryCapacitor Exciter winding in the rotor Battery positive Dynamo field Signal wiring for warning lamp in dash panel insert U, V, W, X, Y, Z - Winding ends of the generating coilTerminal B+S272_080Smoothing capacitor for the onboard power supply voltageThe onboard power supply battery is located in the boot. The length of the charge lead from the alternator to the battery is approx. 6 m. The capacitor has the task of reducing the voltage ripple on the charge lead in the vicinity of the alternator. Smoothing the charge current and charge voltage on the charge lead reduces electrical and acoustic faults. The supply for the high-current electrical equipment, where high voltage ripples can occur, is tapped in the plenum chamber.Onboard power supply electrical equipmentVehicle electrical system batteryElectronics box, plenum chamberS272_02420Charge process of the starter batteryThe charging process of the starter battery can take place in two operating modes: - through the transistor or - the DC/DC converter in the control unit for battery monitoring. As long as the nominal charge voltage of the starter battery is lower than the current onboard power supply voltage, the charge current of the starter battery is fed via the transistor. If the onboard power supply voltage is below the nominal value of the charge voltage, the charge current is fed via the DC/DC converter. The charge time is monitored by the control unit for battery monitoring. If the starter battery does not reach its voltage value within the prescribed parameter, the charging process is cancelled and disabled. This means that a defective battery is not continuously charged. A fault is entered in the fault memory: charge monitoring for starter battery - upper limit value exceeded.Schematic diagramTerminal 50 Relay SStarter batteryTerminal 30SV Terminal 15SV Control unit for entry and start authorisation Control unit for battery monitoring Relay B Relay LTemperature sensorTerminal 15 Terminal 30Relay S = Relay B = Relay L = SV =switch-over relay for starter battery (J580) switch-over relay for onboard power supply battery (J579) relay for parallel switching of batteries (J581) electrical equipment required for startingOnboard power supply batteryS272_023The control unit for battery monitoring has diagnostic capability with the VAS 5051 Diagnostic Testing and Information System.21Onboard power supply managementThe onboard power supply control unit (J519) pools various functions in the vehicle. The various functions that until now were enabled via switches and relays - Parking lights - Dipped beam headlights - Side lights - Turn indicators - Main beam headlights - Fog lights - Footwell lights - Terminal 58 d - Indicator lamp for hazard warning lights - Relay for headlight washer system - Relay for heating wiper park position - Fuel pump feed and - Horn are switched by the onboard power supply control unit.S272_053The onboard power supply control unit is located in the electronics box in the right-hand footwell.Front of device connectorA B C D E F GS272_055Back of device connectorH J K L M N PS272_05422Supply voltageSignal Voltage of onboard power supply battery Voltage of starter battery Voltage of starter battery Voltage of onboard power supply battery Terminal 15 Input from Onboard power supply battery + Starter battery + Starter battery Onboard power supply battery Control unit for entry and start authorisation Output toCAN bus signalsSignal Convenience CAN High Convenience CAN Low Input from Convenience CAN bus Convenience CAN bus Output to Convenience CAN bus Convenience CAN busInput signalsSignal Hazard warning lights Fog lights Automatic lights Mirror heating Dimming Dimming Fault fibre-optic cable Mirror adjustment Fold-in mirror Bonnet opened Side lights Rear fog light Dipped beam headlights Reversing light Mirror adjustment Fog lights Low-beam and main beam headlight, left Input from Button for hazard warning lights Button for fog lights Light switch Switch for door mirror Increase dimmer + Reduce dimmer Headlight, right Switch for door mirror Switch for door mirror Switch for bonnet Light switch Light switch Light switch Switch for reversing light GND switch for door mirror Terminal 30 fuse box Terminal 30 fuse box Output to23Onboard power supply managementInput signal (continued)Signal Low-beam and main beam headlight, left Flashing light, left side light Low-beam and main beam headlight, right Flashing light, right side light Horn Wake up running gear Footwell lights Headlight washer system Input from Terminal 30 fuse box Terminal 30 fuse box Terminal 30 fuse box Terminal 30 fuse box Terminal 30 fuse box Running gear control Terminal 58d Terminal 30 fuse box Output toOutput signalsSignal Fog lights Footwell lighting Instrument lighting Turn signal, left Main beam headlight, left Dipped beam headlight, left Parking light, left Main beam headlight, right Dipped beam headlight, right Turn indicator, right Parking light, right Horn Check of hazard warning lights Heating Headlight washer system Supply line, fuel pump Enable seat heater Input from Output to Fog lights Footwell lights Terminal 58d Instrument Headlight, left Headlight, left Headlight, left Headlight, left Headlight, right Headlight, right Headlight, right Headlight, right Horn Indicator lamp Wiper storage relay HWS pump Fuel pump relay Relay (only in the case of veh. without seat memory control unit) Pop-up washer jet motor, right Pop-up washer jet motor, left Terminal 30aHeadlight cleaning system Headlight washer system Voltage supply +24Special features of the lighting control systemTurn indicators The following turn indicator controls are possible:● ● ● ●These operating modes are arranged by priority: 1 Crash indication 2 Hazard warning lights 3 Turn indication 4 Special functions, e.g. anti-theft alarm system With this arrangement, a flashing function can be activated although another has not been deactivated.Turn indication Hazard warning lights Crash indication Flashing on locking and activating the anti-theft alarm system as well as panic flashing (USA only)The onboard power supply control unit also controls the onboard power supply management so that sufficient electrical energy is available continuously. The onboard power supply management switches off electrical equipment if the battery voltage of the onboard power supply battery falls below a defined value.Side lights and driving lights Emergency function An additional circuit in the onboard power supply control unit ensures that the side lights and dipped beam headlights are also switched on in the case of a defect in the onboard power supply control unit.If a turn indicator light fails, the rate of the indicator lamp is doubled to signal the failure. The indicator lights continue to work at the normal rate. With the hazard warning lights, the indicator lamp flashes at the normal rate.Via the VAS 5051 Diagnostic Testing And Information System, the onboard power supply control unit has diagnostic capability.25Onboard power supply managementMonitoring the onboard power supply voltageThe onboard power supply control unit monitors the charge state of the onboard power supply battery to avoid excessive discharge. From the alternator (Terminal DF), the engine control unit receives the pulse-width modulated (PWM) information regarding the capacity utilisation of the alternator. This information reaches the Convenience CAN bus via the Drive Train CAN bus and the gateway in the dash panel insert. The onboard power supply control unit evaluates the state of the onboard power supply voltage by comparing the DF signal and the onboard power supply voltage. If a critical state of the onboard power supply is detected, the idling speed is increased; in very critical states, convenience electrical equipment is switched off.Drive Train CAN busConvenience CAN busGateway Engine control unit Onboard power supply control unitDF signalBattery voltageS272_018The dynamo field signal can be shown using the VAS 5051 Diagnostic Testing and Information System.26Raising the idling speedIf the voltage of the onboard power supply battery falls below 12.7 volts for longer than 10 seconds, the state of the onboard power supply is classified as critical and the idling speed is raised. The signal for requesting a rise is sent by the onboard power supply control unit via the Convenience CAN bus, the gateway and the Drive Train CAN bus to the engine control unit. The idling speed is raised when the automatic gearbox is in positions 'P' or 'N'. It remains at the increased level if - on transition to vehicle operation - the engine speed was higher beforehand.Drive Train CAN busConvenience CAN busGateway Engine control unit Onboard power supply control unitDF signalIdling speed increaseBattery voltageS272_014The value of the speed increase varies from one engine variant to the next. If the voltage is constantly higher than 12.7 volts for at least two seconds, the state of the onboard power supply is detected as uncritical and the request to raise the idling speed is cancelled.Modifying the engine speed is regulated by the engine control unit according to defined values. Fluctuations in engine speed due to fluctuating voltage values are largely suppressed by the engine control unit.27Onboard power supply managementSwitching off convenience electrical equipmentWith the ignition on or active alternator (engine running), the onboard power supply control is classified by the onboard power supply control unit as very critical if the voltage of the onboard power supply battery is below 12.2 volts for a certain period dependent on the electrical equipment. The result is that convenience electrical equipment is switched off by priority by its control unit. If an item of electrical equipment is not switched on, it is skipped and the next item is switched off.Drive Train CAN busConvenience CAN busGatewayEngine control unit Rise in idling speed 2nd stage Control units involved in switching off electrical equipmentSignals for switching off electrical equipmentOnboard power supply control unit Battery voltageControl unit for air conditioning systemCentral control unit for convenience systemControl unit for steering column electronicsDoor control unit, driver's sideControl unit for seat adjustment - Driver - Front passenger - Rear compartmentOnboard power supply control unitS272_01528If the state of the onboard power supply remains very critical after the convenience electrical equipment has been switched off, a second stage of the idle speed increase is initiated. If this does not improve the state of the onboard power supply, the air conditioning system is also switched off.Switch-off sequenceState of the onboard power supplyReduction in heat output to 50% Seat heater and ventilation off PTC to 25% * Mirror heating off Steering wheel heating switch-off Reduction in air conditioning systemPTC to 75% *PTC to 50% *Switch-off windscreenWiper park position heater offPTC off *Rear window heater offElectrical equipment switch-off* PTC heating element in the rear footwell flapsS272_08429Networked functionsNetworking systemOn today's vehicles, activation and supply of the lighting system can no longer be implemented via conventional switches, relays and cable connections. Networked functions in these vehicles handle the corresponding functions.Schematic diagram with control units involved in lighting control system and networking as an exampleTurn indicators Dipped beam headlights Main beam headlights Parking light Fog lights Rotary door latch Turn indicator in the mirror Courtesy light Door exit light Door handle lighting, interior J234 Airbag control unitInterior lighting Reading lights Convenience lighting Switch for convenience lighting Switch for reading lights J518 Control unit for entry and start authorisationJ386 Door control unit, front passengerJ217 Control unit for gearboxJ285 Dash panel insert gatewayDirection of travelSwitch for interior lights J528 Control unit for sunroof electronics Brake light switchJ519 onboard power supply control unit Light switch J387 Door control unit, driverJ523 Control unit for front information display and operating unitJ527 Control unit for steering column electronicsTurn indicator switch Switch for manual dipping and flasher Turn indicator in the mirror Courtesy lights Door exit light Door handle lighting, interiorHazard warning light switch Dimming + Fog lights Parking light Main beam headlights Dipped beam headlights Turn indicators Dimming Front footwell lightingRotary door latch30Activation signals are sent to control units via resistance-coded switches, and these either activate the electrical equipment themselves or send the activation signal via a databus system to the control unit in charge of activation. The supply of the electrical equipment is then via the control unit in charge.Turn indicators Door exit light Rotary door latch Door handle lighting Brake light Tail light Rear fog light Reversing light J389 Rear right door control unitIndicator lights Brake light Tail light Rear fog light Reversing lightRear footwell lighting Rotary door latch, bootJ521 Control unit for front passenger's seat adjustmentJ393 Central control unit for convenience system boot light Courtesy lighting (rear) Number plate lights 3rd brake light Number plate lightsJ136 Control unit for driver's seat adjustmentJ345 Control unit for trailer detectionRear footwell lightingJ388 Rear left door control unitReversing light Rear fog lightReversing light Rear fog light Tail light Brake light Turn indicatorsRotary door latchDoor exit light Door handle lightingTail light Brake light Turn indicatorsS272_08731Networked functionsBrake light controlControl units involved● ● ●Central control unit for convenience system Control unit for trailer detection (optional) Dash panel insertBy way of illustration, the CAN lines (orange) for the signals are represented individually. In reality, all the signals are sent via a CAN High and a CAN Low line.Brake light switchDash panel insertCentral control unit for convenience systemControl unit for trailer detectionoptionalBrake light, leftBrake light, rightBrake light, leftBrake light, rightBrake light, top centreS272_062Signals 1 Activation of the central control unit for the convenience system and the control unit for trailer detection viathe brake light switch with an analogue voltage 2 Power current to the brake light from central control unit for convenience system or control unit for trailer detection 3 Fault message from central control unit for convenience system to the dash panel insert via Convenience CAN bus; if the brake light is defective, a fault message appears in the display 4 Fault message from control unit for trailer detection to the dash panel insert via Convenience CAN bus; if the brake light is defective, a fault message appears in the display 5 Safety signal. If the activation signal from the brake light switch to the control unit for trailer detection is missing, information is provided through the central control unit for convenience system32Control of side lights and tail lightsControl units involved● ● ● ●Onboard power supply control unit Central control unit for convenience system Control unit for trailer detection (optional) Dash panel insertLight switchFront left side lightOnboard power supply control unitFront right side light Left side light Right side lightDash panel insertCentral control unit for convenience systemControl unit for trailer detectionoptionalLeft tail lightRight tail lightLeft tail lightRight tail lightNumber plate lightsNumber plate lightsS272_045Signals 1 Activation of the onboard power supply control unit by the light switch with an analogue voltage 2 Activation signal from the onboard power supply control unit to the central control unit for convenience system and control unit for trailer detection via Convenience CAN bus 3 Power current to the side lights and tail lights 4 Fault message to the dash panel insert via Convenience CAN bus; if a side light is defective, a fault message appears in the display 5 Fault message to the dash panel insert via Convenience CAN bus; if a tail light is defective, a fault message appears in the display 6 Fault message to the dash panel insert via Convenience CAN bus; if a tail light in the trailer is defective, a fault message appears in the display33Networked functionsLight activation via the light switch or the automatic driving light controlControl units involved● ● ● ●Onboard power supply control unit Dash panel insert Control unit for entry and start authorisation Control unit for sunroof electronicsLight sensorLight switchControl unit for sunroof electronicsControl unit for entry and start authorisationOnboard power supply control unitDipped beam headlight, left Dipped beam headlight, rightDash panel insertS272_048Signals 1 Signal 'Ignition on' from control unit for entry and start authorisation via Convenience CAN bus 2 Activation of the onboard power supply control unit by the light switch with an analogue voltage signal, Vbat approx. 12 volts 3 Power current to the headlightsIf light sensor fitted 4 Analogue brightness signal from light sensor to control unit for sunroof electronics 5 Signal 'Switch on dipped beam headlights' via Convenience CAN bus in the case of automatic driving light control from control unit for sunroof electronics to onboard power supply control unit 6 Fault message to the dash panel insert via Convenience CAN bus; if dipped beam headlight is defective, a fault message appears in the display34Control of the turn indicatorControl units involved● ● ● ● ● ● ●Onboard power supply control unit Control unit for entry and start authorisation Control unit for steering column electronics Dash panel insert Driver's door control unit Front passenger's door control unit Control unit for trailer detection (optional)Turn indicator switchControl unit for steering column electronicsControl unit for entry and start authorisationTurn indicator, front leftOnboard power supply control unitTurn indicator, front right Turn indicator, rear left Turn indicator, rear rightDash panel insertDoor control unit, driverDoor control unit, front passengerControl unit for trailer detectionoptionalSide indicator, left (mirror)Side indicator, right (mirror)Left turn indicatorRight turn indicatorSignals 1 Signal 'Ignition on' from control unit for entry and start authorisation via Convenience CAN bus 2 Signal 'turn indicating' from turn indicator switch into control unit for steering column electronics 3 Signal 'turn indicating' from control unit for steering column electronics via Convenience CAN bus to onboard power supply control unit 4 Power current to the indicator lights 5 Signal 'turn indicating' from onboard power supply control unit via Convenience CAN bus to door control units driver/front passenger and, if present, to the control unit for trailer detectionS272_0476 Signal for activation of the indicator lamps and poss. fault messages via Convenience CAN bus from onboard power supply control unit to dash panel insert 7 Signal for activation of the indicator lamps and poss. fault messages via Convenience CAN bus from control unit for trailer detection to dash panel insert35Networked functionsHazard warning lights controlControl units involved● ● ● ● ●Onboard power supply control unit Dash panel insert Driver's door control unit Front passenger's door control unit Control unit for trailer detection (optional)Hazard warning lights buttonTurn indicator, front leftOnboard power supply control unitTurn indicator, front right Turn indicator, rear leftDash panel insertTurn indicator, rear rightDoor control unit, driverDoor control unit, front passengerControl unit for trailer detectionoptionalSide indicator, left (mirror)Side indicator, right (mirror) Turn indicatorsS272_088Signals 1 Signal 'hazard warning lights' from hazard warning lights button to onboard power supply control unit 2 Signal 'hazard warning lights' from onboard power supply control unit via Convenience CAN bus to door control units driver/front passenger and, if present, to the control unit for trailer detection 3 Power current to the indicator lights 4 Signal for activation of indicator lamps and acoustic check signal and poss. fault messages via Convenience CAN bus from onboard power supply control unit to dash panel insert 5 Signal for activation of the indicator lamps and poss. fault messages via Convenience CAN bus from control unit for trailer detection to dash panel insert36Control of the rear window heaterControl units involved●Control unit, front information display and operating unit Onboard power supply control unit Central control unit for convenience system●Button for rear window heater●Onboard power supply control unitControl unit for front information display and operating unitCentral control unit for convenience systemRelay for heater field 1Relay for heater field 2Rear windowS272_049Signals 1 Signal from rear window heater button to control unit, front information display and operating unit 2 Signal 'Button actuated' from control unit, front information display and operating unit to central control unit for convenience system via Convenience CAN bus 3 Analogue activation of the relay for heater field 1 and 2 on rear window 4 Signal 'Heater fields of rear window switched on' via Convenience CAN bus from central control unit for convenience system to onboard power supply control unit and control unit for front display and operating unit; indicator lamp is switched on 5 Signal 'Power output reduction of rear window heater' via Convenience CAN bus from onboard power supply control unit to central control unit for convenience systemThe upper and lower heater fields of the rear window are activated separately. In the case of an overload of the onboard power supply control unit, the onboard power supply control unit reduces the heat output by 50%. The heater fields are activated alternately.37Networked functionsControl of windscreen heaterControl units involved●● ● ●Control unit, front information display and operating unit Onboard power supply control unit Control unit for air conditioning system Dash panel insertThe windscreen heater is switched on by the control unit for air conditioning system depending on the ambient temperature. The switch-on time is based on the ambient temperature: +5 to 0°C = 2 minutes 0 to -20°C = 4 minutes -20 to -40°C = 6 minutesActivation via the defrost button is only possible when the engine is running, when the ambient temperature is colder than +5°C, and there is no engine load limitation.Onboard power supply control unitButton DefrostDash panel insertControl unit for front information display and operating unitControl unit for air conditioning systemControl unit for windscreen heaterWindscreen heaterSignals 1 Signal 'Windscreen heater on' with manual operation 2 Forwarding of signal 'Windscreen heater on' in the case of manual operation from control unit for front display and operating unit for information to control unit for air conditioning system via Convenience CAN bus 3 Signal 'Engine speed 0 rpm' from dash panel insert to control unit for air conditioning system via Convenience CAN bus 4 Signal 'Switch-off windscreen heater' in the case of load limitation from onboard power supply control unit via Convenience CAN busS272_0505 Signal 'Windscreen heater on' from control unit for air conditioning system to dash panel insert as well as information signal 'Windscreen heater on' from control unit for air conditioning system to onboard power supply control unit via Convenience CAN bus 6 Activation to control unit for windscreen heater to switch on the windscreen heater38Control unit for windscreen heatingIn order to enhance convenience and safety (fogged or iced windows), a heated windscreen is used. The windscreen is heated by means of an integrated metal foil. Due to the necessary electrical power output of approx. 1000 watts, as a result of the foil resistance, a voltage is required that exceeds the onboard power supply voltage of 12 volts. This voltage is provided by the control unit for the windscreen heater (DC/DC converter). Depending on the input voltage, an output voltage of up to 42 volts DC and power output of up to 1000 watts is provided.P1000 WOutput voltage100 W U 12.2 V Input voltage 12.7 V 13.1 VS272_089A crack in the windscreen or a short circuit is detected by the control unit. The windscreen is then not heated. The control unit for the windscreen heater is located in the rear right of the boot.Control unit for windscreen heaterS272_094Starter battery39SwitchesResistance-coded switchesSwitches serve to switch electrical components and functions on and off. In the case of conventional switches, one cable connection per switch function is required. Resistance-coded switches need a considerably lower number of cable connections.Functional example Switch for steering wheel adjustmentSwitch open If all the switches are open, no signal is transmitted to the steering column module.Switch for steering wheel adjustmentSteering column module down up back forwardS272_064Switch 'down' is actuated Via contact A2, the steering column module transmits a voltage signal to the switch. This voltage signal is changed by resistance R4. As the resistances R1, R2, R3 and R4 are different, the control unit recognises the switch position.Steering column module down upSwitch for steering wheel adjustmentbackforwardS272_06540Dash panel1 2 3 4 5 6 7 8 9/10111213143S272_0261 Fog light, optional 2 Rotary light switch 3 Vent flow restrictor 4 Rear fog light 5 Instrument lighting 6 Reset trip recorder 7 Tiptronic 8 Tiptronic +9 Turn off parking aid 10 Rear roller blind up/down 11 Turn indicators and main beam headlights 12 Steering wheel adjustment 13 Wipers 14 Electronic ignition lock41SwitchesFront information display and operating unit1 2 3 4 5 6 7 8 9 10 11 12 13 Air conditioning temperature, driver's side Automatic air conditioning, driver's side Windscreen defrost Air conditioning toggle Quattro/Mono Hazard warning light switch Air conditioning air recirculation Rear window heater Automatic air conditioning, front passenger's side Air conditioning temperature, front passenger's side Softkeys for menu control Switch-over menu on screen Radio operating keys Rotary/push knob 1 2 3 4 5 6 7 8 9101011 131112S272_039Multi-function steering wheel1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 APC or CCS On/Off APC Distance +/APC or CCS Cancel Key lighting On/Off (on the back) APC or CCS APC or CCS Set APC or CCS Resume APC or CCS + Volume + Answer telephone call Navigation announcement Volume Menu selection, forward List selection Menu selection, backward8 7 6 5 4 3 2 19 10 11 12 13 14 15S272_027Driver's door1 Locking/unlocking doors (in driver's and front passenger's door)1S272_03142Driver's door1 Defroster vent, driver's door12 3 4 5 6 7 8 9Bootlid open Tank filler flap release Front right window regulator Right child-proof lock Rear right window regulator Rear left window regulator Left child-proof lock Front left window regulator2 3 4 7 5 6S272_0309 8Centre console1 2 3 4 5 6 7 8 9 Deactivation, front passenger's airbag Indicator lamp, deactivation front passenger's airbag Seat heater and ventilation, front passenger (optional) Damper setting ESP switch Air suspension adjustment Seat heater and ventilation, driver, and steering wheel heating (optional) Mirror adjustment, mirror heating, optional mirror folding function Ignition and starting engine, optional 1 2 9 876543S272_038Driver's and front passenger's seat1 2 3 4 5 4-way adjustment lumbar support Belt height adjustment Position memory of seats (3 positions, 1 set) Seat adjustment Massage On/Off123 45S272_02943SwitchesRear roof module1 2 3 4 Rear left reading light On/Off Interior light via door contact On/Off Interior light On/Off Rear right reading light On/Off1234S272_037Front roof module1 2 3 4 5 6 Trigger for programmed remote control ( e.g. open garage door) Interior light On/Off Reading light On/Off Control of sliding/tilting roof Hands-free microphone for driver (car phone and voice operation) Interior light via door contact On/Off123 63 45S272_03644Operating elements on the console in the rear1 2 3 4 5 6 7 8 9 Vent flow restriction, centre rear right Switch-over to seat control, front passenger's seat Rear right seat setting Rear right seat heater and ventilation Rear right seat memory (2/3 positions and massage at 2 positions) Rear left seat memory (2/3 positions and massage at 2 positions) Rear left seat heater and ventilation Rear left seat setting Vent flow restriction, centre rear left1 2 3 498765S272_032Rear air conditioner/Climatronic operating and display unit (four-seater)1 2 3 4 5 6 7 8 9 10 11 12 Rear right head vent Rear right body vent Rear right foot vent Rear right manual temperature control Rear right automatic control Fan +/Rear left automatic control Rear left manual temperature control Rear left foot vent Rear left body vent Rear left head vent Display 11 10 9121 2 3 45 8 7 6S272_033As regards operation of a retrofitted version, please consult the manual.Rear doors1 Locking/unlocking doors1New!S272_03545Dash panel insertThe dash panel insert is designed as a premium version with a 5" colour TFT screen (thin-film transistor) and a highline version with a 3" monochrome dot-matrix screen.S272_056The top-of-the-range dash panel insert has the following functions: Analogue displays●5" colour TFT screen●● ● ●● ● ●Speed (country-specific in kph, mph + kph, kph + mph) Engine speed Fuel gauge Coolant temperature (country-specific in °C/°F) Oil temperature (country-specific in °C/°F) Onboard power supply voltage (V) Odometer display (total distance driven, trip counter)● ● ● ● ● ● ● ● ● ● ● ● ● ●The on-board computer can be switched to country-specific units Driving time Distance Average speed Average consumption Momentary consumption Ambient temperature/ice warning Remaining distance Maintenance due indicator Gear selection for automatic Alarm indications with pictograms Navigation/radio data APC displays Tyre pressure warning Lamp failure displayHighline dash panel insert● ● ●a 3" monochrome dot-matrix screen a clock with LC display in the rev counter a total distance driven and trip counter with LC display in the speedometer46Layout of the display1 2 Audio part display Warnings Multi-function display Warnings Automatic proximity control main screen Voice input Navigation main screen Car phone Telematics Audio Buttons of the multi-function steering wheel that can be activated APC part screen Audio list Car phone list Navigation: current road Warnings Marker for warnings Gear selection display Total distance driven Ambient temperature Trip counter Red symbol for APC1234160 k m/h16039412.3km 12.3oCP R N D3 S5123456km876S272_0824 5 6 7 8 9The display areas 1, 2 and 3 are assigned according to the priority of the displays to be shown. High, red warnings:●Danger or cars downMedium, amber warnings:●MessagesLow:●Information47Dash panel insertExisting driver informationDriver information ABS APC displays Airbag displays Ambient temperature Onboard power supply voltage Lack of brake fluid Brake fault, EBD fault Brake wear Damper function Damper fault Dynamic oil warning Engine speed EPC Ice warning ESP/TCS displays Turn indicator check, trailer Turn indicator check, left/right Main beam headlights Handbrake Total distance driven Speed Light bulb failure Light bulb failure, brake light ID sender 'Battery warning' ID sender not authorised (immobiliser) ID sender not detected Fuel gauge Lack of coolant Coolant temperature Coolant overheating Coolant overheating Lack of coolant e.g. check rear fog light Please check brake light Key battery empty Key not authorised e.g. system fault, workshop!123456km 12.3oCAnalogue displaySymbolsText messages e.g. APC defective e.g. airbag fault Electrics: electrical equipment switch-off e.g. brake fluid, stop vehicle! e.g. brake fault, stop vehicle! Check brake pads e.g. Sport FaultOil pressure, engine off!Release handbrake!48Driver information Charge control Steering wheel cannot be locked Steering wheel locked Steering defective Headlight range control failure Light warning Bonnet, doors, bootlid open, childproof lock Fog lights Rear fog light Self-levelling function Level, fault Emergency start EOBD Oil temperature Oil level too low Oil level sensor defective Tyre pressure control displays Key warning Shift lock Seat belt, driver Trip counter Fuel warning Gear selection display Place selector lever in position 'P' Service due indicators Washer fluid levelAnalogue displaySymbolsText messages Alternator, workshopPlease move steering wheelLocking: press start/ stop for longer period Steering defective, workshop Check headlight range control e.g. switch on side lightse.g. vehicle lowering Fault Please start engine e.g. engine fault Check oil level Oil sensor fault, workshop!e.g. tyre pressure control offKey not found Press brake Driver: fasten seat belt123.4kmPlease refuelD3Place selector lever in position 'P' e.g. Service now Add washer fluid49NetworkingDatabus topologyThe databus system has been expanded to a great extent. It has three subsystems, the - Drive Train CAN bus, - Convenience CAN bus, - Infotainment CAN bus.G259 Sender for proximity controlJ217 Control unit for autom. gearboxJ343 Control unit for gas discharge headlight, leftJ539 Control unit for brake servo unitLateral accel. + yaw rateJ367 Control unit for battery monitoringJ344 Control unit for gas discharge headlight, rightJ519 Onboard power supply control unitJ104 ABS with ESP control unitJ197 Self-levelling suspension control unitJ584 Control unit for wiper motor, front passenger's sideJ400 Control unit for wiper motorTurbocharger 2Only V10 TDi Control unit for turbocharger J518 Control unit for entry and start authorisationMulti-function steering wheelInterior monitor; rain sensor/ light sensor; sliding/tilting roofJ528 Control unit for sunroof electronicsOnly V6 TDi Engine CU slave on W12 and V10 TDiJ399 Control unit for injection pump Mir ReceiveJ527 Control unit for steering column electronicsJ301 Control unit for air conditioning systemJ624 Engine control unit -2-J234 Airbag control unit J526 Control unit for car phone / telematicsJ623 Engine control unitJ285 Dash panel insert (Gateway)50Diagnosis via the databusGatewayCAN busThe diagnosis via the communications line only takes place now in the case of a few control units in the Drive Train CAN bus subsystem, the gas discharge headlights and in the central control unit for the convenience system.Drive Train CAN bus Convenience CAN bus Infotainment CAN bus SlaveCommunications line Virtual communications line Optical databus*J657 Control unit for power latching*J389 Rear right door control unit*If J523_H fitted, no air conditioner operating unit and vice versa!J345 Control unit for trailer detectionJ388 Rear left door control unitJ522 Control unit for rear seat adjustment with memory*J446 Control unit for parking aidJ387 Door control unit, front passenger's side*J521 Control unit for front passenger's seat adjustment with memoryAll other control units, except for the analogue clock, the control units for turbochargers 1 and 2, the injection pump and the control unit for trailer detection have a virtual communications line. Diagnosis is performed via the bus system. The control units send their diagnostic data via the gateway in the dash panel insert to the diagnostic testing and information system. In the case of a defective dash panel insert, no diagnosis of control units is possible using the virtual communications line.J502 Control unit for tyre pressure monitoringJ386 Door control unit, driver's sideJ136 Control unit for driver's seat adjustment with memoryE265 Rear operating and display unit for air conditioning systemJ393 Central control unit for convenience systemJ605 Control unit for tailgate angle sensorThe control unit for trailer detection as well as the analogue clock do not have self-diagnostic capability.J401 Navigation control unit with CD driveJ523 Control unit, front information display and operating unitR 41 CD changerJ524 Control unit, rear information display and operating unitJ525 Control unit for digital sound packageOptical databusY Analogue clockR 78 TV tunerJ167 Control unit for additional heatingS272_05751NetworkingThe control units in the Drive Train CAN busThe Drive Train CAN bus operates at a data transfer rate of 500 kbit/s. The data is transmitted via the CAN High and CAN Low line. If one of these lines is defective, has a short circuit or an interruption, data transfer is no longer possible or only to a limited extent.J623 Engine control unit J624 Engine control unit -2J539 Control unit for brake servo unitJ367 Control unit for battery monitoringJ197 Self-levelling suspension control unitJ217 Control unit for autom. gearboxJ527 Control unit for steering column electronics J285 Dash panel insert (Gateway) J518 Control unit for entry and start authorisation G259 Sender for proximity control J104 ABS with ESP control unit J234 Airbag control unitS272_07652Linking the Drive Train CAN busThe control units are networked using a combination of linear and star-shaped links.G259 Sender for proximity controlJ104 ABS with ESP control unit J539 Control unit for brake servo unitJ217 Control unit for autom. gearboxJ624 Engine control unit -2-J623 Engine control unitJ285 Dash panel insert (Gateway) J234 Airbag control unit J527 Control unit for steering column electronicsJ518 Control unit for entry and start authorisationJ197 Self-levelling suspension control unitJ367 Control unit for battery monitoringS272_05853NetworkingControl units in the Convenience CAN busThe Convenience CAN bus operates at a data transfer rate of 100 kbit/s. Data is transmitted via the CAN High and CAN Low line. If one of these lines is defective, has a short circuit or an interruption, data transfer is possible only via one line.The databus goes to single-wire mode. Various control units are designed as masters and communicate with their slaves via an internal data line to which only they have access. Slaves are executing control units that run the instructions from their master, e.g. switching on the wiper motor.J393 Central control unit for convenience system J528 Control unit for sunroof electronicsJ605 Control unit for tailgateE265 Rear operating and display unit for air conditioning systemJ446 Control unit for parking aid J345 Control unit for trailer detectionJ387 Door control unit, front passenger's sideJ389 Rear right door control unitJ523 Control unit, front information display and operating unit J519 Onboard power supply control unitJ502 - Control unit for tyre pressure monitoring J388 Rear left door control unit J386 Door control unit, driver's side J527 Control unit for steering column electronics J285 Dash panel insert (Gateway) J400 Control unit for wiper motor J301 Control unit for air conditioning system J518 Control unit for entry and start authorisationS272_07454Linking the Convenience CAN busThe control units are networked using a combination of linear and star-shaped links.J527 Control unit for steering column electronicsJ285 Dash panel insert (Gateway)J528 Control unit for sunroof electronicsJ301 Control unit for air conditioning system J387 Door control unit, front passenger's sideJ386 Door control unit, driver's sideJ400 Control unit for wiper motorJ518 Control unit for entry and start authorisationJ523 - Control unit for front information display and operating unit J519 Control unit for onboard power supplyJ388 Rear left door control unitJ389 Rear right door control unitE265 Rear operating and display unit for air conditioning systemJ521 Control unit for front passenger's seat adjustment with memoryJ136 Control unit for driver's seat adjustment with memoryJ524 Control unit, rear information display and operating unitJ502 Control unit for tyre pressure monitoringJ522 Control unit for rear seat adjustment with memoryJ345 Control unit for trailer detectionJ393 Central control unit for convenience systemJ446 Control unit for parking aidS272_05955NetworkingControl units in the Infotainment CAN busThe Infotainment CAN bus operates at a data transfer rate of 100 kbit/s. The data is transmitted via the CAN High and CAN Low line. If one of these lines is defective, has a short circuit or an interruption, data transfer is possible only via one line.The databus goes to single-wire mode. The front and rear control units, information display and operating units as well as the navigation control unit communicate with one another via an optical bus to which only they have access.J523 Control unit, front information display and operating unitY Analogue clockJ526 Control unit for car phone / telematics R78 TV tunerJ401 Navigation control unit with CD driveR41 CD changerJ525 Control unit for digital sound package J524 Control unit, rear information display and operating unitJ285 Dash panel insert (Gateway) J167 Control unit for auxiliary heatingS272_07556Linking the Infotainment CAN busThe control units are networked using a combination of linear and star-shaped links.J167 Control unit for auxiliary heatingY Analogue clockJ401 Navigation control unit with CD driveJ523 Control unit, front information display and operating unitJ285 Dash panel insert (Gateway)Optical busJ524 Control unit, rear information display and operating unit J525 Control unit for digital sound package J526 Control unit for car phone/ telematics R 78 TV tunerS272_06057NetworkingOptical databusThe front control unit, information display and operating unit as well as the navigation computer communicate with one another via an optical bus to which only they have access. The optical databus operates at a data transfer rate of 11.2 Mbit/s. The available bandwidth is suitable for transmitting data from the navigation CD-ROM. On the connection level, this optical bus system is based on a single polymer fibre-optic cable that connects all the devices in a ring topology. The information is received via an optical receiving diode and is forwarded via a transmitting diode. Due to the ring-shaped design, overall failure of the databus is unavoidable if one node is unable to pass on the information.J401 Navigation control unit with CD driveOptical data lineJ523 Control unit, front information display and operating unitS272_091Receiving diodeWhen laying fibre-optic cables, special care is necessary, as it is only possible to bend them up a maximum radius of 25 mm.J401J523Transmitting diodeReceiving diodeJ524S272_09058GatewayThe gateway control unit is integrated in the dash panel insert as software; it controls communication traffic over the bus systems - Drive Train, - Convenience and - InfotainmentDrive Train CAN bus 500 kbit/s Dash panel insertConvenience CAN bus 100 kbit/sEngine control unitGatewayOnboard power supply control unitInfotainment CAN bus 100 kbit/sControl unit, front information display and operating unitS272_06659Analogue clockThe high-quality analogue clock is integrated in the wood trim strip of the dash panel in the vehicle centre. The time is set using the control unit for the front information display and operating unit. The signals are transmitted via the CAN bus. In the case of vehicles with navigation system, the time is synchronised by the Global Positioning System (GPS) via the navigation computer.Dash panel insertAnalogue clock GatewayNavigation control unit with CD driveControl unit, front information display and operating unitS272_06760GlossaryCAN bus A large number of control units are required in today's motor vehicles. In order to implement their functions, data interchange among them is absolutely necessary. The conventional method of interchanging information via individual cable connections has reached its limits. The CAN bus connects the control units with two bi-directional data lines. Data transfer is digital. Polymer fibre-optic cable This lead comprises fibre-optic cable, comparable with flexible Plexiglas, through which digital light signals can be transmitted for data transfer without loss. Fibre-optic cables are a modern transfer medium, operating on an optical basis. The data is transported by means of high-frequency light pulses.TFT screen Dot-matrix screen Numbers, letter and characters are shown on the screen as interrelated dots. Thin Film Transistor screen, technology used for flat monitors; provides good contrast and a clear picture.Electrical equipment required for starting Electrical equipment absolutely necessary for starting:● ● ● ● ● ●Engine control unit Fuel pump Electronic ignition lock Dash panel insert Control unit for entry and start authorisation Airbag control unitGlobal Positioning System This navigation system developed by the US Ministry of Defense makes world-wide navigation possible. With currently 24 to 27 satellites, the accuracy of position determination is ideally under 10 m.61Test your knowledge1. What are the power management components? a) The starter battery, the onboard power supply control unit, the relay for parallel switching of batteries, the switch-over relay for starter battery, the switch-over relay for onboard power supply and the onboard power supply battery b) The starter battery, the control unit for battery monitoring, the relay for parallel switching of batteries, the switch-over relay for starter battery, the switch-over relay for onboard power supply battery and the onboard power supply battery c) The starter battery, the control unit for battery monitoring, the relay for parallel switching, the switch-over relay for starter battery, the main relay and the onboard power supply battery2. Which statement is correct? a) In the case of vehicles with petrol engine and two-battery onboard power supply, both batteries are connected in series at temperatures below -20°. b) In the case of vehicles with petrol engine and two-battery onboard power supply, both batteries are switched in parallel at temperatures below +5°. c) In the case of vehicles with petrol engine and two-battery onboard power supply, both batteries are switched in parallel at temperatures below -10°.3. What functions are switched through the onboard power supply control unit? a) Parking lights, main beam headlights, central locking, dipped beam headlights b) Fog lights, side lights, indicator lights, footwell lights c) Horn, indicator lamp for hazard warning lights, relay for headlight washer system624. Which statement is correct with regard to switching off convenience electrical equipment in the case of a very critical onboard power supply? a) Convenience electrical equipment is switched off by priority. b) Convenience electrical equipment is switched off depending on the amount of power consumption. c) Convenience electrical equipment is switched off in the order they were switched on.5. Which control units are involved in turn indicator activation? a) The steering column switching module, the control unit for entry and start authorisation, the onboard power supply control unit, the door control unit on the driver's and front passenger's side a) The steering column switching module, the control unit for entry and start authorisation, the indicator relay,