TECHNICAL DOCUMENTATION
SSP 273 Phaeton Convenience

This PDF is currently unavailable.
Read document text
Service.Self-Study Programme 273Phaeton Convenience and Safety ElectronicsDesign and FunctionOpen sesame - thanks to a new system for entry and start authorisation, the Phaeton can be accessed without actively using a key (1). The opening request is detected via an aerial in the outer door handle (2) and authorisation is identified via a control unit (3). The opening request is detected via an aerial in the outer door handle (2) and authorisation is identified via a control unit (3).Rear CU to door control unit: unlock!"OK!""Request received!" Aerial CU to entry and start system: Authorisation OK? "Yes, accepted!" Enty system to rear control unit: Please open! Please enter! "Hey aerial: opened!""All clear, unlocked!"S273_093Further information about the Phaeton can be found in the following Self-Study Programmes:● ● ● ● ● ● ● ●Self-Study Programme 250: Self-Study Programme 270: Self-Study Programme 271: Self-Study Programme 272: Self-Study Programme 274: Self-Study Programme 275: Self-Study Programme 276: Self-Study Programme 277:The Phaeton - W12 - Engine Management The Phaeton The Phaeton - Heating and Air Conditioning System The Phaeton - Onboard Power Supply The Phaeton - Infotainment System The Phaeton - Air Suspension with Dynamic Damping The Phaeton - Automatic Proximity Control The Phaeton - Running GearNEW Important NoteThis Self-Study Programme explains the design and function of new developments. The contents are not updated.Please always refer to the relevant Service Literature for all inspection, adjustment and repair instructions.2Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Entry and start authorisation . . . . . . . . . . . . . . . . . . . . . . . . 8Convenience system central control unit . . . . . . . . . . . . . 24Roof module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Multi-function steering wheel. . . . . . . . . . . . . . . . . . . . . . . 52Sound system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Parking aid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72Test your knowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 763IntroductionThis Self-Study Programme provides you with an overview of the complex convenience and safety electronics in the Phaeton. It provides information, for instance, about:- the new solar sliding/tilting roof with road speed-dependent wind deflector- the new windscreen wiper system with two separate, electronically controlled motors- the new orientation light for safe entering and exiting in the dark- a parking aid that warns against obstacles not only visually, but also acoustically4- seats adjustable in all directions with air conditioning memory and massage function- a sound system specially tuned to the car interior- the multi-function steering wheel to operate the main functions- the new system for entry and start authorisation without the use of a keyS273_0175IntroductionSystem overview of convenience and safety electronicsDash panel insert (Gateway) Steering column electronics control unit Roof electronics control unit Control unit for air conditioning systemSlave Door control unit, driver's side Wiper motor control unit (master)Door control unit, front passenger's sideFront central display and control unit control unitControl unit for entry and start authorisationOnboard power supply control unitDoor control unit, rear leftDoor control unit, rear rightControl unit for air conditioning systemSeat adjustment (with memory) control unit, front passengerSeat adjustment (with memory) control unit, driverRear central display and control unit control unitControl unit for tyre pressure monitoringSeat adjustment (with memory) control unit, rearBootlid control unitCentral control unit for convenience systemParking aid control unitLegend Drive Train CAN bus Convenience CAN bus Infotainment CAN bus CAN databusS273_0456ComponentDesignation in current flow diagram J 519 J 528 J 533/J 285 J 605 J 393 J 518 J 255 J 527 J 446 J 502 J 136 J 521 J 522 J 386 J 387 J 388 J 389 J 400 J 584 J 523 J 524Address word for selfdiagnosis 09 38 19/17 via 46 46 05 08 16 76 65 36 06 66 via 46 via 46 via 46 via 46 68 via 68 07 27Other information SSP 272 SSP 273 SSP 273 SSP 273 SSP 273 SSP 273 SSP 271 SSP 273 SSP 273 SSP 270 SSP 273 SSP 273 SSP 273 SSP 273 SSP 273 SSP 273 SSP 273 SSP 273 SSP 273 SSP 274 SSP 274Onboard power supply control unit Roof electronics control unit Gateway in dash panel insert Bootlid control unit Convenience system central control unit Entry and start authorisation relay Climatronic control unit Steering column electronics control unit Parking aid control unit Tyre pressure monitor control unit Seat adjustment (with memory) control unit, driver Seat adjustment (with memory) control unit, front passenger Seat adjustment (with memory) control unit, rear Door control unit, driver's side Door control unit, front passenger's side Door control unit, rear left Door control unit, rear right Wiper motor control unit (master) Windscreen wiper control unit, front passenger's side (slave) Control unit, front information display and operating unit Rear information display and operating unit control unit7Entry and start authorisationComplete overviewThe adjacent diagram provides an overview of the components involved in the system for entry and start authorisation.Gear change mechanism with selector lever lock and button for entry and start authorisationEntry and start authorisation switchElectro-mechanical steering column lock8Rear aerials in the bumperInterior aerialsOuter door handles with electronicsIgnition key with radio-wave remote controlEntry and start authorisation relayS273_0909Entry and start authorisationWhen suitable equipment is available, the convenience functions for the entry and start authorisation system (KeylessStart Exit and Security System) make it possible to lock and unlock the vehicle and to switch the engine on and off by radio-wave remote control without actively using the ignition key. The system is offered in two equipment variants:● ●Basic equipment (standard equipment) Convenience equipment (optional)Overview of equipment variantsComponents Entry and start authorisation switch Terminal control (Terminal 15SV, 15, 75, 50)* Immobiliser (Immobiliser III) Radio-wave remote control (RRC) for central locking Electro-mechanical steering column lock activation (ESL) Button for entry and start authorisation Interior and exterior aerials Central locking button in the outer door handles Proximity sensors Transponder for Immobiliser III and entry and start authorisation Anti-theft alarm system Interior monitor* Terminal 15SV: Power supply of electrical equipment required for start Terminal 15: Power supply ignition "on" Terminal 75x: Power supply/relief relay Terminal 50: Power supply starter/solenoidBasic equipment X X X X XConvenience equipment X X X X X X X X XXX X X10Basic equipment componentsEntry and start authorisation switch Ignition key with radio-wave remote controlReader coilEngine control unit (rpm)Gate selector lever P/N signal*Electro-mechanical steering column lockEntry and start authorisation relay Gearbox control unit* Clutch pedal switch for manual gearboxS273_055Basic equipment for vehicle entry and starting the engine The vehicle is unlocked using the unlocking button on the ignition key with radio-wave remote control (RRC). To unlock the steering column, the ignition key must be inserted into the entry and start authorisation switch. By means of the immobiliser (coil) in the entry and start authorisation switch, a request is sent to the entry and start authorisation relay for ignition key authorisation. If the control unit makes a positive identification, the steering column is unlocked. Turning the ignition key in the entry and start authorisation switch switches Terminals 15, 75(X) and 15SV. Further turning (Terminal 50 on) starts the engine, providing the following conditions are met:● ●P/N signal (automatic gearbox) Clutch applied (manual gearbox).If there is radio interference, or the vehicle or ignition key battery has discharged, the vehicle may be entered using the mechanical emergency lock cylinder in the driver's door or in the bootlid.11Entry and start authorisationIgnition key with radio-wave remote control The radio-wave remote control functions in the usual way: to unlock the vehicle door, the unlock button must be pressed on the radio-wave remote control. The control unit for entry and start authorisation evaluates the radio signals. The convenience system central control unit activates the standard functions for the central locking system.Unlocking buttonS273_050Immobiliser (Immobiliser III) The immobiliser also functions as before together with the entry and start authorisation switch, which carries the reader coil, and the engine control unit.Reader coilS273_048Entry and start authorisation switchEntry and start authorisation switch The operating concept for the entry and start authorisation switch has been very slightly changed. The positions are:● ●Zero SelectOn Start● ●Off = ignition/engine off Zero = Automatic reset of the ignition key after switching on the engine On = ignition on Start = engine onS273_047Switch positions for entry and start authorisation12Electrical release disable control unitThe electrical release disable control unit ensures that the ignition key cannot be inadvertently removed from the entry and start authorisation switch. The ignition key cannot be removed while● ●the ignition is on (Terminal 15 on) and if the gate selector lever for the automatic gearbox is not in P position.Gate selector lever P signalDash panel insertEntry and start authorisation relayGearbox control unitEntry and start authorisation switchS273_051Each key fits mechanically into the entry and start authorisation switch and can be turned. Once the ignition key has been authorised (transponder), it is enabled by the immobiliser (IM III).13Entry and start authorisationElectro-mechanical steering column lock (ESL)This is an electro-mechanical version of the conventional mechanical steering column lock, which means that it has an electrical interface to the entry and start authorisation relay and a mechanical interface to the steering column. The ESL is encoded and activated by means of the entry and start authorisation relay. When the key is inserted or withdrawn, the steering column is locked or unlocked by means of the entry and start authorisation relay. The steering column is supplied with voltage for this procedure only, otherwise the ESL has no voltage (deenergised). The ignition can only be activated when the steering column is unlocked.Entry and start authorisation relayElectro-mechanical steering column lockEntry and start authorisation switchS273_09714Soft startThe soft start is initiated via the drive train CAN databus between the entry and start authorisation relay and the engine control unit. If the start position (Terminal 50 on) in the entry and start authorisation switch is flicked, the starter stays in the ON position until the engine is running. To protect the starter and avoid unnecessary noise, the start position of the starter is only activated until the engine has reached idling speed even if the starter is activated for a longer period of time. The engine control unit receives this message from the engine speed sender and transmits the information to the entry and start authorisation relay, giving the command to shift the starter out of position (Terminal 50 off). The entry and start authorisation relay switches the following relays: Relay Terminal 15: voltage supply Relay Terminal 15 SV: voltage supply Relay Terminal 75X: voltage supply Relay Terminal 50: voltage supplyEmergency startIf the onboard power supply battery has discharged, an emergency start is possible when the engine is not running by means of the battery management control unit and the entry and start authorisation relay.Relay Dash panel insertEngine control unit Entry and start authorisation relay Entry and start authorisation switchS273_098Please refer to Self-Study Programme 272 of "The Phaeton - Onboard Power Supply" for more detailed information about battery management. 15Entry and start authorisationAdditional convenience equipment functionsThanks to the additional convenience equipment functions, the ignition key with radio-wave remote control (RRC) is required to open and lock the vehicle, but it no longer needs to be activated. The engine can also be started and switched off without actively operating the ignition key using the authorised transponder. The additional functions of the convenience equipment are as follows:● ●●Opening the vehicle without actively operating the ignition key with the authorised transponder Starting the engine by means of a button for entry and start authorisation without actively operating the ignition key with the authorised transponder Locking the vehicle without actively operating the ignition key with the authorised transponderConvenience equipment componentsButton for entry and start authorisationExterior aerialsInterior aerialsAerial SensorElectro-mechanical steering column lockOuter door handle with electronicsDoor control unit16Entering the vehicle using the convenience equipmentIf the user approaches the vehicle with an authorised ignition key, touching the outer door handle with the entry and start authorisation relay transmits an inductive request to the transponder in the ignition key via the exterior aerial in the door handle. If the control unit recognises the ignition key as authorised for entry, it transmits this information to the convenience system central control unit. The convenience system central control unit gives the door control unit the command to unlock the requested vehicle door. The door control unit unlocks the vehicle door. It is possible to enter the car using any door, opening either a single door or all of the doors, depending on the coding. If the control unit for entry and start authorisation fails to function, the vehicle door can be unlocked via the emergency lock cylinder in the door lock on the driver's side. The bootlid can be unlocked by means of the emergency lock cylinder in the bootlid (concealed in the VW emblem).Ignition key with radio-wave remote control and transponder Entry and start authorisation switchRelayEngine control unitEntry and start authorisation relayGearbox control unitConvenience system central control unitS273_10117Entry and start authorisationAerialsCentre armrest aerial R139 Rear shelf aerial R137 1 aerial in each bumper R1361 R135 aerial each at front and rearInterior switch recess aerial R1381 R134 aerial each at front and rear Tunnel aerial R139S273_102Interior aerials The interior aerials detect an ignition key with authorised transponder in the vehicle interior for the starting cycle, vehicle operation and locking procedure. The interior aerial range extends without interruption throughout the entire vehicle interior. The detection range for the interior aerials does not overlap with the detection range for the exterior aerials.18Exterior aerials The exterior aerials detect an ignition key with authorised transponder for the locking and unlocking procedure. The position of the ignition key with authorised transponder can be allocated specifically to the driver's side, front passenger's side or to the bootlid. The exterior aerials have a range of approximately 1.50 m radiating from the place at which they each operate - vehicle doors and bootlid - at a height of 0.1 m to 1.8 m.Exterior aerial detection rangeS273_05619Entry and start authorisationOuter door handles with electronicsIf convenience equipment is fitted, the aerials, sensors and central locking buttons are located in all outer door handles and may be used to open and close the vehicle doors without actively using the ignition key with radio-wave remote control:●●●one aerial on each of the driver's side and front passenger's side for entry and start authorisation R134, R135* one sensor on each vehicle door for contact on the driver's side G415, G417 and front passenger's side G416, G418 one button on each vehicle door for central locking on the driver's side E369, E371 and front passenger's side E370, E372.* The aerials in the outer door handles should be regarded as a single aerial per vehicle side (front and rear).AerialCapacitive sensorCentral locking buttonS273_109Driver's side and front passenger's side aerials for entry and start authorisationBy means of the aerial in the ignition key with radio-wave remote control and authorised transponder, an encoded signal is transmitted to the aerial in the outer door handle, thus inducing voltage in the aerial. This message is transmitted to the entry and start authorisation relay, which in turn evaluates the signal.Aerial (coil)S273_105S273_10320Sensors for contact on the driver's side and front passenger's sideIf a hand approaches the outer door handle, the capacitance of the sensor in the outer door handle changes. The entry and start authorisation relay recognises the change in the capacitance of the sensor as proximity to the outer door handle or as a request to enter the vehicle.S273_107Capacitive sensorS273_104Buttons for central locking on the driver's side and front passenger's sidePressure on the central locking button initiates an inductive request through the entry and start authorisation relay to the ignition key with radiowave remote control and transponder. If the ignition key is recognised as authorised and outside the vehicle but within the range of the vehicle, the command is enabled to lock the vehicle.Hand operated switchS273_108 S273_10621Entry and start authorisationStarting the engine without an ignition keyFor this function the ignition key with authorised transponder need not be inserted into the entry and start authorisation switch. It must, however, be located inside the vehicle interior in order to initiate an inductive request via the interior aerials when the button for entry and start authorisation is moved to the first engaging position. The ignition key gives an encoded response to the entry and start authorisation relay. If the ignition key is identified as authorised, the electro-mechanical steering column lock (ESL) is unlocked and the NO contact activated when the first stage of the button for entry and start authorisation is activated. If the button is then moved to the first engaging position, the ignition is switched on.Switching off the engine without an ignition keyThe engine can also be turned off with the button for entry and start authorisation. To do this, move the button for entry and start authorisation to the second engaging position by pressing it once.Gear change mechanism with selector lever lockButton for entry and start authorisationS273_099Locking the vehicle without an ignition keyActivating a central locking button (fitted to all outer door handles) initiates a request for a valid ignition key with authorised transponder in the exterior of the vehicle. The ignition key transmits a response to the entry and start authorisation relay. Once the ignition key has been positively identified, the vehicle door is locked via the convenience system central control unit.S273_10022If the vehicle is locked and a second ignition key with authorised transponder is still located in the vehicle interior, the latter is disabled for start authorisation and the vehicle is locked!Learning-in the system for entry and start authorisationAs the system contains the immobiliser,● ● ●●the entry and start authorisation relay, electro-mechanical steering column lock (ESL) the ignition key with radio-wave remote control and the engine control unithave to match one another. This is carried out at the end of the production line or during servicing using the VAS 5051 Diagnostic Testing and Information System.In order to provide better anti-theft protection it is only possible to change just one of the four components; otherwise the system must be subjected to a learn-in process if new components are fitted.The system for entry and start authorisation has self-diagnostic capability via the addresses● ●05 Control unit for entry and start authorisation and 25 Immobiliser III (diverted to 05).23Convenience system central control unitThe convenience system central control unit monitors and controls the following functions:● ● ● ● ● ● ● ● ●Convenience system central control unit●●central locking unlocking the fuel filler flap window regulators interior monitor anti-theft alarm system tilt sensor rear lighting bootlid light control unit activation for the bootlid rear window heater (refer to Self-Study Programme 272 "The Phaeton Onboard Power Supply") bootlid lock control with automatic closingS273_029Rear shelfCentral locking (CL) systemThe central logic of the central locking system for the doors and bootlid is stored in the convenience system central control unit. The functions are triggered by the entry information and the commands are transmitted to the door control units and the bootlid control unit. In the case of vehicles with standard equipment, the central locking is activated as before by using the button on the ignition key with radio-wave remote control. In the event of a fault the vehicle can be locked and unlocked by using a mechanical emergency lock cylinder in the driver's door.Functional sequence The door control units provide information via the convenience CAN databus. The convenience system central control unit evaluates this information and controls the central locking functions. The door control units evaluate the messages from the convenience system central control unit and activate the motors for the central locking. In the convenience equipment of the system for entry and start authorisation, the convenience system central control unit receives the central locking command from the entry and start authorisation relay.24Operating units for the central locking system● ● ● ●Radio-wave remote control Lock/Unlock button in all doors Driver's door lock cylinder (emergency locking) System for entry and start authorisation (optional)Lock/unlock buttonS272_082Emergency functions Communication between the convenience system central control unit and the door control unit takes place via the CAN databus. If the CAN messages cannot be received by the door control units (for example if the convenience system central control unit is defective), the following emergency functions are initiated:●●●●●●After five messages have not been received, all door control units detect that no further messages are being transmitted by the central control unit. The driver's door control unit assumes control of central locking. All other door control units react to the messages from the driver's door control unit. The signals from the driver's door lock cylinder, as well as those from the lock/unlock button become command signals and the operating units of the other doors cease to work. When operated, the lock cylinder takes priority over the button. If the CAN connection to the driver's door is interrupted, the door can only be activated manually by means of the lock cylinder; the lock/unlock button does not function.Behaviour in a crash Information about a crash is transmitted via the CAN databus. A signal is transmitted from the convenience system central control unit to unlock the central locking.25Convenience system central control unitUnlocking the fuel filler flapThe fuel filler flap is unlocked if:●Remote release switch for the fuel filler flap●●there is a request made by means of a CAN message from the driver's side door control unit, the vehicle road speed is below the preset speed threshold and the vehicle has not been locked from outside.S273_067Power regulatorsAll window regulators have decentralised electric control and, for safety reasons, have a roll-back function when the window regulator motor has been learned-in. The convenience system central control unit generates the CAN signals for the convenience opening and closing functions.Interior monitor (IM)The IM in the roof module is activated and deactivated by means of the convenience system central control unit per CAN databus. Each IM operating state is transmitted back to the convenience system central control unit, including the alarm signal, if the IM has been triggered.The driver can deactivate the IM once for this cycle between switching off the ignition and activating the ATA via the front central display and operating unit (CDC).Sensors for interior monitorFront roof moduleS273_08926Anti-theft alarm system (ATA)The anti-theft alarm system function is integrated in the convenience system central control unit. The information necessary for activation and deactiviation is provided by the entry and start authorisation relay. Communication takes place via the convenience CAN databus.Activating the ATA When the vehicle is locked with the radio-wave remote control, this status is transmitted via the CAN databus and the ATA is activated. The ATA can also be activated by actuating the emergency locking cylinder. In the convenience version of the Entry and Start Authorisation system, when locking the vehicle, the ATA is activated using the locking button in the outer door handles. If Terminal 15 is engaged or the driver's door opened, the ATA is not activated.Deactivating the ATA Authorised access is transmitted by a radio-wave remote control key via the CAN databus, causing deactivation. If the vehicle is entered by means of the mechanical emergency lock cylinder (if there is interference to radio communication or the radio-wave remote control key battery has discharged), Terminal 15 must be engaged at the latest after 15 seconds, otherwise the ATA will be deactivated.27Convenience system central control unitTilt sensorThe tilt sensor ensures that the vehicle cannot be towed away without authorisation. The tilt sensor mechanism is based on what is known as the conductometric technique. It determines the change in resistance if there is a change in the volume of a viscous, electrically conductive liquid. Electrodes arranged at different positions project out of this liquid. Electrodes arranged at different positions project out of this liquid. If the position of the sensor changes (if the vehicle is raised on one side), then the distribution of the fluid in the chambers also changes. When the level of the fluid in the compartments changes, the resistance determined across the electrodes in the chambers also changes. The change in the position of the tilt sensor caused by inclining the vehicle to one side changes the resistance. This is stored and activates the anti-theft alarm system. This is stored and activates the anti-theft alarm system.S273_131SubcompartmentCeramic housing Indicator fluid Electrode Electrode connections Operational amplifierS273_13228Rear lightingThe convenience system central control unit controls the following lighting functions:● ● ● ● ● ● ●●Right/left rear and marker light Left/right brake light 3rd brake light Left/right reversing light Rear fog light Number plate light Rear courtesy light or self-illuminating number plate Boot lightNumber plate lightingS273_129Automatic closingThe automatic closing motor ensures that the bootlid is securely closed as soon as a rotary latching contact is energised.29Convenience system central control unitBootlid control unitThe bootlid control unit controls the complete bootlid opening and closing procedure and is assigned as a slave to the convenience system central control unit. It receives its information via a serial interface from the convenience system control unit and transmits its status and diagnostic messages back via the same interface.Bootlid control unitRear shelfS273_060Exterior buttonWith basic equipment:●●The central locking is unlocked = press the button to open The central locking is locked = button activation is ignoredWith convenience equipment:●●The central locking is unlocked = press the button to open The central locking is locked = pressing the button triggers authorisation; in the event of a positive result the bootlid is opened.S273_064Emergency lock cylinder Bootlid exterior buttonFor both types of equipment the exterior button for the bootlid is deactivated if the speed threshold is exceeded. It is enabled when a vehicle door is opened.The convenience system central control unit and bootlid have selfdiagnostic capability using the VAS 5051 Diagnostic Testing and Information System via address word 46.30The bootlid is openedeither by means of●Switch for bootlid, driver's door●●the bootlid switch on the inner side of the driver's door under the speed threshold of 6 km/h, or the bootlid radio-wave remote control button (RLR), or the exterior bootlid button (concealed in the VW emblem).S273_065The bootlid is closedmanually in the basic version,●manuallyBootlid radio-wave remote control button (RLR)and with convenience equipment (with hydraulics) by using● ● ●●the button in the bootlid, the radio-wave remote control or the switch on the inner side of the driver's door, and the exterior switch in the VW emblem.Bootlid interior buttonS273_083The bootlid can only be shut if the bootlid has been learned-in (end position learned-in). Refer to the current Service Literature for information on how to carry out the learn-in process.Pinch protection functionA force limitation mechanism for the hydraulic pump clearly identifies any likelihood of anyone trapping a hand etc. when opening and closing the bootlid.S273_063Danger: During self-diagnosis "basic setting", there is no pinch protection function!31Roof moduleVarious electrical components are integrated in the roof module which are not all part of the same function system. Various electrical components are integrated in the roof module which are not all part of the same function system. For this reason not all components are controlled by the roof electronics control unit; some are controlled via separate control lines.Components activated directly by the roof module:● ● ● ● ● ●Not directly activated by the roof module:●● ● ●●Interior lighting Interior lighting control Control for Terminal 30G Garage door opener Interior monitor (IM) Electronically controlled interior rear-view mirror with memory function (optional) Rain sensor Light sensor (optional) Humidity sensor and windscreen temperature sensor Control for sliding/tilting roof (refer to chapter entitled "Sliding/tilting roof“).●●Indirect dash panel lighting via the onboard power supply control unit Instrument lighting via the onboard power supply control unit Hands-free microphone via the car phone/telematics control unitThe humidity sensor and windscreen temperature sensor are assigned to the climate control system and are described in Self-Study Programme 271.32Front roof module1 2 3 4 5 6 7 8 9 10 Hands-free microphone driver's side Driver's side reading light Driver's side reading lightOn/Off Interior light automatic function On/Off Sensors for interior monitor (optional) Actuation of garage door opener (optional) Actuation of interior light On/Off Actuation of reading light front passenger On/Off Rotary switch sliding/tilting roof (optional) Front passenger reading light5654 3 27 8 9 101S273_015Rear roof module1 2 3 4 5 Rear left reading light Rear left reading light On/Off Interior light automatic function On/Off Actuation of interior light On/Off Rear right reading light12345S273_07433Roof moduleInterior lightingThe interior light plus the driver's and front passenger reading lights and their switches are integrated in the roof module. The roof module assumes control of the interior lights in the vehicle. The necessary information is transmitted via the convenience CAN databus as shown in the following example:● ● ● ● ●Rotary latch contact (door open) NO contact (ignition key inserted) Terminal 15 (ignition "on") Anti-theft alarm system (ATA) triggered Crash signal (crash intensity).Interior lighting controlSwitching the voltage supply for the interior lights, the reading lights and the vanity mirror lights is part of the interior lighting control.To control the following lighting, the necessary information for the control units concerned is also provided by the roof module via the convenience CAN databus.●●●The footwell lighting is dimmed and switched on and off by means of the seat control units as soon as the interior light in the roof module is switched on or off manually or automatically. The door exit warning lights are switched on undimmed by means of the door control units when doors are open. The door courtesy lights are switched on if a door is opened, an unlocking command exists, the ATA alarm is active or the automatic driving light control* has been activated.●The inner door handle lighting is switched on if a command is sent to the roof module via the convenience system central control unit to lock the vehicle. The interior door handle lights are activated via the door control units. The intensity of the inner door handle lighting is controlled via Terminal 58d. If Terminal 15 is on, it is activated at full brightness.* For more detailed information on the automatic driving light control system please refer to the chapter entitled "Automatic driving light control" in this Self-Study Programme.34Control for Terminal 30GTerminal 30G is switched via the roof module and supplies the voltage for the glove box and vanity mirror lights. A pulse width modulated signal (PWM signal) is generated in the roof module.Terminal 30G switches on under the following conditions:● ●Terminal 30G switches off under the following conditions:●Terminal 15 is switched on and the run-on period for the supply switched on has not expired.●●●after Terminal 15 has been switched off, if no interior light or reading light has been switched on for 30 seconds, an hour after Terminal 15 has been switched off and the interior light or reading light has been switched on, after an hour if Terminal 15 has been switched off and an interior light or reading light is switched on, immediately after all the conditions for switching off the dimmed front interior light have been met.35Roof moduleGarage door openerThe garage door opener is supplied as an option. Up to three different garage door openers can be activated by means of the roof module. The driver must be responsible for learning-in the function of the garage door opener, as the function can vary depending on the manufacturer. The garage door opener is only active if Terminal 15 is switched on. After Terminal 15 is switched off it remains active for a run-on period of 10 minutes. The run-on period is interrupted if a door is opened.S273_115Garage door opener in the front roof moduleInterior monitor (IM)The interior monitor (IM) is controlled via the roof electronics control unit. The sensor technology is integrated in the roof module. The information necessary for control is transmitted by the convenience CAN databus. The roof electronics control unit detects any tripping via the IM sensors and transmits this by means of the convenience CAN databus. The convenience system central control unit receives this information and triggers the functions of the anti-theft alarm system (ATA).Connector for the garage door opener Connector for the interior monitor (IM)S273_08036Activating the IM The IM is activated via the convenience system central control unit (anti-theft alarm system master).Sensors for interior monitor (IM)Deactivating the IM Deactivating the IM depends on deactivating the anti-theft alarm system (ATA) by unlocking the central locking system. It is possible to switch off just once and bring about subsequent locking via the front central display and control unit (CDC).S273_089Front roof moduleFor more detailed information about the anti-theft alarm system (ATA) please refer to the chapter entitled "Convenience system central control unit“.37Roof moduleElectronically controlled interior rear-view mirror with memory functionThe use of Electronic PhotoChromic (EPC) gel inside the automatic anti-dazzle interior mirror (electronically controlled interior rear-view mirror) allows it to automatically change the reflection when the light sensor detects an impinging bright light. By● ● ●Front roof moduleengaging reverse gear, switching on the interior light and deactivating the electronically controlled function through the button on the bottom of the mirror,Electronically controlled light sensorS273_075the roof electronics control unit adjusts the interior rear-view mirror for maximum brightness. Information about the selected reverse gear is received via the CAN databus.Interior rear-view mirror memory functionBasic adjustment for the interior rear-view mirror is carried out manually. The position of the interior rear-view mirror is recorded by two feedback potentiometers (x, y axis) and stored in the roof module. This stored information is transmitted via the convenience CAN databus to the seat control unit on the driver's side. Where there is appropriate equipment, in order to adjust the stored interior rear-view mirror position assigned to a memory button, the roof module receives the command from the driver's side seat control unit via the convenience CAN databus. This position is adjusted by means of two positioning motors in the mirror housing.Feedback potentiometerPositioning motors Electronically controlled light sensorS273_072For further information on the electronically controlled interior rearview mirror please refer to Self-Study Programme 200 "The Golf ´98“.38Rain sensorThe rain sensor is supplied with voltage by the roof electronics control unit. Signals output by the rain sensor are sent in the form of commands to the wiper motor control unit via the convenience CAN databus.Front roof moduleThe rain sensor is activated by means of the "Intermittent" and "Automatic" positions on the steering column switch (also refer to the chapter entitled "Wiper module".Rain sensorS273_075S273_071Sensitive surfaces of the rain sensorThe roof module is capable of self-diagnosis through the VAS 5051 Diagnostic Testing and Information System using address word 38 ("Roof electronics").39Roof moduleSliding/tilting roof (STR)The sliding/tilting roof (STR) is supplied with dimensions of 520 x 900 mm and with two equipment variants:● ●Glass roof or solar roofMotor for glass roofsolar roof glass roofSolar roof version The solar cell power output of 24 watts is used by activating the ventilator fan for the interior ventilation even if the ignition is not switched on.S273_073Motor for wind deflectorSliding headliner Headliner motor in glass roof versionOperating the sliding/tilting roof (STR) The sliding/tilting roof (STR) is operated by means of the rotary switch on the roof module after it is by the convenience system central control unit. The roof electronics control unit outputs the signals to the sliding/tilting roof to enable the sliding/tilting roof and convenience opening and closing. Evaluation of the STR switch also takes place in the sliding/tilting roof. The STR function is enabled: - when the ignition is switched on (Terminal 15 on), - for a run-on period of 10 minutes after the ignition is switched off (Terminal 15 off), - as long as no door is opened. If the driver's door is opened within the run-on period, the sliding/tilting roof enable function is cancelled.For further information about the sliding/tilting roof please refer to SelfStudy Programme 270 "The Phaeton“.40Glass roof version For the glass roof version, the roof module has two additional buttons at the front on the rotary switch to operate the roller blind. In the glass roof version the sliding headliner is activated electrically by a separate motor.S273_086Rotary switch in the front roof module with E 437 button for roller blind/sunroofConvenience opening and closing function Convenience operation allows the electric windows and a fitted sliding/tilting roof (STR) to be fully opened and closed. The function is configured via the front central display and control unit (CDC). The STR is not enabled by the convenience system central control unit until after the window regulators have reached the end position (if this convenience function is configured). The function is only active while it is being activated.Emergency closing function The "emergency closing" function is triggered by pressing the dot in the middle of the rotary switch. The sliding/tilting roof immediately travels to zero position with increased holding power.Emergency closingS273_088The sliding/tilting roof is capable of self-diagnosis through the VAS 5051 Diagnostic Testing and Information System using address word 38 (roof electronics).41Roof moduleAutomatic driving light controlThe automatic driving light control extends the previous number of functions on the rotary light switch. Firstly, the automatic driving light control (ALC) has a safety function. If the rotary light switch is positioned on the "automatic driving light control" function (tunnel light symbol), the entire vehicle lighting is switched on automatically at a brightness relative to the ambient light levels as detected by light sensors. The light sensors are read by the roof module. The automatic driving light control switches the following lighting on:● ● ● ●Symbol for tunnel lightS273_004Rotary light switch with "automatic driving light control" functiondipped beam tail light courtesy lights number plate lightsThe lighting function that is activated by means of the rotary light switch always takes priority over the light function automatically selected by the automatic driving light control!The tunnel light symbol is visible on the speedometer for a few seconds when the automatic driving light control is switched on.S273_005For simple faults such as processor failure, a defective sensor or an open circuit, the entire vehicle lighting is always switched on.42System overviewRain sensor/light sensors in roof moduleRoof electronics control unit Rotary light switchControl unit for entry and start authorisationOnboard power supply control unitTerminal 15Dipped beam front left Dipped beam front rightCentral control unit for convenience systemSide light front leftSide light front rightSide light left side Number plate lights Side light right side Right and left tail lightS273_0071 Terminal 15 on 2 Automatic driving light control 3 Light (dipped beam) on 4 Tail light (parking light) on 5 Dipped beam on6 Front right or left dipped beam defective 7 Rear left and right parking light and number plate lighting defectiveAn additional circuit in the onboard power supply control unit ensures that the side lights and dipped beams can be switched on and off even if the µC fails!43Roof moduleSensor The sensor comprises the following functions:● ●rain sensors and light sensors (optional)The sensor is mounted on the windscreen (top centre) and linked electrically to the roof module.S273_075Ambient light sensor/rain sensorDirectional sensorsS273_111The light sensor technology consists of the following components:●Three directional sensors with a viewing direction horizontal to the vehicle with a beam width of 10° for each sensorS273_006●An ambient light sensor with viewing direction vertical to the vehicle and with a beam width of 10° and 80° to the side.S273_113S273_112The ambient light sensor also works as a rain sensor.44Conditions for switching on When the vehicle enters a tunnel, the vehicle lighting is immediately switched on. It is switched off again with a time delay of 5 seconds after leaving the tunnel (this avoids flashing the lights by constantly switching on and off). By contrast, the vehicle lighting is not activated when passing bridges and travelling through short underpasses or in fog, as the horizontally arranged light sensor - in contrast to the vertically arranged light sensor - is able to detect light. In such cases the vehicle lighting must always be adjusted manually as required.Rain sensor function If it rains, the vehicle lighting is activated after 10 seconds by a rain sensor using infrared detection. It is deactivated again if no further rain is detected for 200 seconds. The rain sensor also detects how severe the rain is and automatically activates the windscreen wipers and regulates the rate at which they wipe (refer also to the chapter entitled "Windscreen wiper module“).45Roof moduleOrientation lighting The convenience functions of orientation lighting assist the vehicle occupants by automatically switching on the vehicle lighting when they enter and leave the vehicle.The entire interior lighting is switched on via the radio-wave remote control for up to four minutes after the vehicle doors are unlocked. This function is cancelled again when:S273_013● ●●the maximum time for this function has expired the orientation lighting is switched off via the CDC "Settings" menu the ignition is switched on.22.5°C92.1 MHzTP 21.0°CSettings Orientation lightingRun-on lighting time for the headlightsBack2:30 minS273_019The orientation lighting switches the entire interior lighting off with a delay after occupants leave the vehicle when:● ●The status of the interior lighting is not affected by the function of the orientation lighting. The last value for the orientation lighting in each case is stored in the onboard power supply control unit and used if the CAN signals fail.●●the ignition is switched off, the vehicle lighting was switched on beforehand for at least three seconds, after opening a vehicle door, the system detects that all vehicle doors have been closed again, the vehicle doors are opened and closed again, as long as the orientation lighting is still activated and the battery protection time of 180 seconds has not yet elapsed.If there is no light sensor fitted, the lights will also be switched on during the day!46System overview of orientation lightingFront information display and operating unit for informationControl unit for entry and start authorisationRotary light switchTerminal 15 Onboard power supply control unit Dipped beam front left Dipped beam front rightRoof electronics control unit Light sensorDriver side door control unitFP side door control unitRear left door control unitRear right door control unitCentral control unit for convenience systemCourtesy lightCourtesy lights Rotary door latchRotary door latchRotary door latchCourtesy lightsRotary door latchS273_0081 Orientation lighting activated 2 Terminal 15 off 3 Rotary light switch was switched on beforehand (dipped beam) 4 Light sensor reports darkness, rotary light switch is set to automatic driving light control 5 Door open, rotary latch contact 6 Automatic driving light control active, switch on dipped beam7 Courtesy lighting for outer door handle 8 Orientation lighting activeAutomatic driving light control is capable of self-diagnosis through the VAS 5051 Diagnostic Testing and Information System using address word 49.47Roof moduleWindscreen wiper moduleThe windscreen wiper module is a new development. It offers:●●●●●●a dual motor wiper system without wiper linkage (small crankshaft drive) minimum noise from the wiper blades at turning points due to reduced wiper motor speed uniform wiping quality depending on road speed and wind pressure intermittent wipe controlled according to vehicle road speed wiper blade protected by alternating park position in the up or down direction lowered wiper arm park position outside range of vision (heated).V217 Front passenger's side wiper motor (slave)V216 Driver's side wiper motor (master)S273_125Activating the wiper module The control electronics for the speed-regulated two-brush wiper motor is integrated in the gearbox cover and activates the wiper motor. The wiper motor on the driver's side (master) receives the wiping requests via a CAN interface. The wiper motor on the driver's side (master) receives the wiping requests via a CAN interface. The driver's side wiper module (master) on the other hand activates the windscreen washer pump directly.48Wiper motor (master) The wiper arm is moved up and down by reversing the wiper motor (master). To achieve this, the motor terminal voltage changes poles in the reverse positions. To regulate the wiper speed, the motor speed and position of the wiper arm are measured by Hall senders on the armature and gearwheel.Voltage regulatorMOS-FETOutput stage driverTwo-brush motorµCSerial interfaceCAN transceiverHall sender on gearboxHall sender on armatureS273_069Voltage regulatorMOS-FETOutput stage driverµCSerial interfaceCAN transceiverHall sender on gearboxHall sender on armatureS273_07049Roof moduleSwitch positions and intervals The Phaeton has the following switch positions:1 Continuous wipe Stage 2 2 Intermittent wipe Stage 1 (rain sensor active) 3 Wipe function off 4 Flick wipe3 1 2In the intermittent position it is possible to activate the wipers at three different speeds, depending on the level of wetness on the windscreen.4S273_091To renew the wipers, the wiper arms must be moved to a vertical position via the front central display and control unit (CDC)! Please do not remove the wipers independently!50Wiper park position, heatedLight/rain sensorRoof electronics control unitSteering column electronics control unitControl unit, front information display and operating unitHeating relay for washer jetsOnboard power supply control unitWiper motor control unit (master) Washer pumpTerminal 75A Relay headlight washer system pump Pop-up washer jets Left right brake lightSide light switchControl unit for wiper motor, front passenger's side (Slave)Dash panel insert Gateway)Washer fluid sensorS273_00951Multi-function steering wheelIn the interior of the multi-function steering wheel, in addition to the horn, there are two button panels for activating frequently used functions. The left button panel serves the functions of the automatic proximity control (APC) with cruise control system (CCS). Infotainment system functions are operated using the right button panel.Left button cluster●+ CCS: Current speed increased in steps of 10 km/h SET: Stores current speed as a desired speed in steps of 1 km/h and activates the APC or CCS RESUME: Activates the APC or CCS at the most recently selected required speed - CCS: Reduces the desired speed in steps of 10 km/h CANCEL: Switches the APC or CCS to standby mode and stores the desired speed Rotary wheel: Adjusts the APC distance ON/OFF: Activates the APC or CCS after starting the engine●●●●●●On the side at the rear of the button module there is an additional button for switching off the button illumination. For further information on the functions of the left button panel and on the subject of automatic proximity control (APC) with cruise control system (CCS)please refer to Self-Study Programme 276 "The Phaeton Automatic Proximity Control".52The steering wheel buttons are connected to the control unit for steering column electronics which transmits data via the convenience CAN databus to the dash panel insert or the control unit, and the front display and control unit (CDC). The gateway in the dash panel insert manages the data interchange between the convenience CAN databus and the drive train CAN databus.The multi-function steering wheel is capable of self-diagnosis through the VAS 5051 Diagnostic Testing and Information System using address word 16.Right button panel●+ Vol: Increases the volume of all audio functions Car phone receiver, Initiates or terminates telephone connections Announces the most recent navigation information - Vol: Reduces the volume of all audio functions Menu selection: Swaps between onboard computer, car phone and Infotainment Press/rotate thumbwheel: Menu selection (by turning the thumbwheel) and selection confirmation (by pressing the thumbwheel) ESC: Fades-in the previous display on the display in the dash panel insert or stops a procedure that is running●●●●●S273_068For further information on the functions of the right button panel and on the subject of "Infotainment“ please refer to Self-Study Programme 274 "The Phaeton - Infotainment System".●On the side at the rear of the button module there is an additional button for switching off the steering wheel heating.53Sound systemFor the Phaeton there is a choice between the 8-channel standard sound system or the 12-channel Premium sound system (optional). The 8-channel sound system comprises●The 12-channel sound system comprises:● ●10 loudspeakers (190 W) and an analogue amplifier12 loudspeakers (270 watts) and a digital amplifierComponents and fitting locations*Tweeter, in the mirror triangleWoofer/mid-range, device carrier panel, front doorWoofer, device carrier panel, front doorMid-range/tweeter, inner door actuation, front door (12-channel sound system only)Woofer, device carrier panel, rear doorMid-range/tweeter, inner door actuation, rear door8-channel analogue or 12-channel digital amplifier, on left in bootS273_043* The loudspeaker fitting locations apply to both the left and right side of the vehicle.54AmplifierThe 12-channel digital amplifier offers the following extended range of functions compared with the analogue amplifier:●Plug-in connections● ●generate various room modes (pop, classical, jazz) and other effects (space, echo) optimised effect for each individual seat vehicle-specific settings (fabric/leather seats; right/left-hand drive models)S273_124J525 Digital sound package control unitBoth types of amplifier also generate the alert tones for the parking aid acoustic warning (also refer to the chapter entitled "Parking aid").It is possible to identify whether an 8-channel analogue amplifier or a 12-channel digital amplifier is fitted in the vehicle by the colours of the plug-in connections for the amplifier: if they are grey and green, then it is an analogue amplifier; digital amplifiers have black plug-in connections. Please refer to the current Workshop Manual for further information about the sound system.The sound system is capable of self-diagnosis through the VAS 5051 Diagnostic Testing and Information System using address word 47.55Sound systemCar phoneThe fixed-network car phone is fitted in the front passenger's armrest. The car phone is operated by means of● ●●the receiver, the front control unit and central display and control unit (CDC) or Multi-function steering wheelThe hands-free microphone fitted on the driver's side in the roof module is used for transmission.Car phone in front passenger armrestS273_119The car phone aerial (GSM) is integrated invisibly in the upper area of the rear window (also refer to the chapter entitled "Aerials". This means that aerials on the roof or bootlid are no longer necessary.Car phone aerial (GSM)S273_034The car phone control unit is fitted on the rear shelf in the boot.For further information on how to operate the car phone, please refer to Self-Study Programme 274 "The Phaeton - Infotainment System".Car phone/ telematics control unitRear shelfS273_03256Overview of car phone systemLoudspeakersLoudspeakersHands-free microphone in the front roof moduleJ525 Digital sound package control unitJ285 Dash panel insert (Gateway)J523 Front central display and control unit for informationFixed-network car phoneMulti-function steering wheelJ526 Car phone/telematics control unitCar phone aerial (GSM)S273_033The car phone system is capable of self-diagnosis through the VAS 5051 Diagnostic Testing and Information System using address word 77.57Sound systemNavigation systemThe CD player for the navigation system is fitted in the glove box. To use the system, the navigation CD must be inserted in the player. The navigation CD player can also receive the Infotainment system CD. Or it can be used to display information, for example, in other languages. The navigation system is operated via the front central display and control unit (CDC), and also via the rear CDC if the car is equipped accordingly.R41 CD changer and J401 navigation system with CD drive control unit in the glove boxS273_036A particularly large map section can be displayed in full screen mode on the 7" screen.Enter destination Store destination Alt. route22.5°C92.1 MHzNAVIGATIONTP 21.0°C Full screen DisplayPlace of destinationDistance in kmVOLKSWASection39OtherSANDKAMPRoute guidanceMap section in the CDC displayS273_039The navigation aerial (GPS) is invisibly integrated under glass in the upper part of the rear window.Navigation aerial (GPS)The navigation system is capable of self-diagnosis through the VAS 5051 Diagnostic Testing and Information System using address word 37.S273_03458Optical bus The front and rear information display and operating unit control units and the navigation control unit intercommunicate via an optical databus to display a digital map.J401 Navigation control unit with CD driveOptical fibre bus (OF)Optical fibre bus The control units are connected in a ring by means of an optical fibre bus (OF). The optical fibre bus must be handled with extreme care:● ●●●do not kink or crush the optical fibre cable, do not bend the FO cable at bending radii of less than 25 mm, do not remove the protective cap until just before installation, if the protective cap is missing, you may have to renew the optical fibre cable.J523 Front information display and operating unit control unitS272_091Optical fibresProtective capS273_127J 401 Navigation system control unit with connector for optical busS273_12659Sound systemCD changerThe 6-disc CD changer is located next to the navigation computer in the glove box. At least one CD must be loaded in the CD changer to play an audio CD. When a CD slot is occupied, it is indicated by an illuminated LED above the relevant station button.S273_037The CD changer is operated via the audio unit in the front central display and control unit (CDC).S273_038TV tunerThe TV tuner is fitted on the right on the rear shelf in the boot. The TV aerials are invisibly integrated in the upper part of the rear window. For safety reasons, while the vehicle is travelling occupants only have access to sound and not to an image on the CDC screen. The TV function is operated via the audio unit in the front central display and control unit (CDC).S273_12860AerialsThe following aerials are fitted invisibly in the upper border of the rear window:● ●●car phone aerial (GSM*) navigation aerial (GPS*) (combined in one housing), aerial module.GSM GPS aerial module.S273_034* GSM = Global System for Mobile communication GPS = Global Positioning SystemThe following are integrated into the aerial module:● ●●●●diversity aerial, aerial booster for the four radio aerials (FM 1-4, AM), four aerial boosters for the active TV aerials (1-4), Telestart aerial for the auxiliary heating (passive), passive aerial for remote central locking (RCL).All aerial conductors are invisibly concealed in the upper area of the rear window. All aerial conductors are invisibly concealed in the upper area of the rear window. The car phone aerial (GSM) and the navigation aerial (GPS) are also fitted in a module in the upper border of the rear window. However, it is not linked to the conductors in the rear window.GSM/GPSFM/TV4Telestart FM/TV1 auxiliary heatingFM/TV2FM/TV3AMRCLConnection in upper heater panel each 165W Connection in lower heater panelS273_08161SeatsThe following front seat options are available:● ●12-way seat 18-way seat (optional).Depending on the type of equipment, both seat variants contain a wide range of functions such as● ● ● ● ●seat adjustment memory functions seat ventilation and heating massage easy-entry function12-way seatThe 12-way seat offers the following options for electrical adjustment: 1 Longitudinal adjustment 2 Belt height adjustment 3 Backrest adjustment 4 Inclination adjustment 5 4-way lumbar support (up/down; front/back)4 1S273_0782 5 36212-way seat controls The seats are operated by means of buttons located on the side of the front seat.Belt height adjustmentMemory buttonsStoring the memory functionsLumbar support Seat adjustment MassageS273_11812-way seat motors The adjacent figures provides an overview of the seat adjustment motors fitted in the 12-way seat: 1 Motor for longitudinal adjustment 2 Motor for height adjustment 3 Motor for backrest adjustment 4 Motor for inclination adjustment 5 Motor for horizontal lumbar support 6 Motor for vertical lumbar support 7 Seat control unit for memory7 4 1 2 5 6 3S273_12263Seats18-way seat (optional)In addition to the functions on the 12-way seat, the 18-way front seats has the following functions: 1 electric recline adjustment 2 extendible seat cushion 3 head restraint adjustment31All memory functions, the seat heater, ventilation and massage functions are contained in the 18-way seat. Non-perforated leather is available as an option for the seats; in this case, the seat ventilation function is not fitted.2S273_0796418-way seat controls In addition to the seat adjustment functions available in a 12-way seat, the 18-way seat has an extendible seat cushion.Belt height adjustmentMemory buttonsStoring the memory functionsLumbar support massageFront/back electric recline adjustment and up/down head restraint adjustmentSeat adjustment Extendible seat cushionS273_12018-way seat motors The adjacent figure provides an overview of the additional motors fitted for seat adjustment in the 18-way seat:11 Electric recline adjustment 2 Extendible seat cushion 3 Head restraint adjustment 4 Seat control unit for memory432S273_02165SeatsRear seatsThe rear seats may be supplied optionally as a single rear bench seat designed for three people or as individual seats for two people.Rear bench seatThe rear bench seat is available in two equipment variants:●Rear bench seat:●with side airbags and manually adjustable head restraints (seat heater optional) Rear bench seat "plus": with electric 6-way lumbar support adjustment in the outer seats, ventilation, massage, seat heater, manually adjustable head restraints and seat occupancy detection (the head restraints rise automatically when the seat is occupied and the seat heater is enabled).The controls for the rear bench seat function are located on the side of the seats.Individual seatsIn addition to the rear bench seat functions, the two individual seats offer the following electrical 10-way auxiliary functions:●● ● ●extendible seat cushion, seat tilt, the height of the head restraints and adjustment of the 4-way lumbar support (up/down; front/back), memory function, Easy-Entry function (the seats move back 10 cm automatically when the door is opened) and seat occupancy detection (see above).The individual seats are only fitted in combination with 18-way front seats.66Individual seatsS273_130Controls for adjusting the front passenger's seat The controls for the individual rear seats are located in the rear central console. In the version that has individual rear seats, it is possible to adjust the front passenger's seat from the rear compartment. This enables rear seat passengers to obtain more leg-room and makes it easier to exit the vehicle.S273_02667SeatsMemory functionsThe following functions can be stored electrically using the memory functions (optional in 12-way seat, standard in 18-way seat):● ● ● ●individual seat adjustments the position of the steering column with easy-entry function for the steering column the position of the seat belts (height adjustment) the settings for the interior and exterior mirrorsIn addition to the 12-way seat memory functions, the 18-way seat has electric adjustments for the head restraints, extendible seat cushion and the recline.System overview of memory functionsMemory buttons 1, 2, 3 Control unit for entry and start authorisationFront central display and control unit (CDC)Central control unit for convenience systemSteering column electronics control unitSeat adjustment (with memory) control unit, driverGateway in dash panel insertRoof electronics control unitDoor control unit, driver's sideDoor control unit, front passenger's sideFront central display and control unit for informationS273_02268Seat heater and ventilationThe seat heater integrated in the seat works together with a fan to feed air at the right temperature evenly through the perforated leather via air ducts. The seat heater and storage of the memory position are regulated by the seat control unit. The required heater and ventilation positions are set by means of the seat heater potentiometer. If the driver's side seat heater is active, the steering wheel is heated simultaneously. If the onboard power supply is overloaded, the steering column heater and