TECHNICAL DOCUMENTATION

SSP 233 20 litre Engine

PDFEN41 pages3 MB
SSP 233 20 litre Engine - PDF cover

This PDF is currently unavailable.

Read document text
Service.Self-Study Programme 2332.0-litre EngineDesign and Function The 2.0-litre engine stems from a successful engine generation and has a long history. The engine blocks of the 1.6-litre and 1.8-litre engines have a similar design. The functions of components such as the coolant pump, radiator, oil pump and oil pump motor are identical. A notable feature of these engines is their closed system control loops which greatly reduce the pollutant emission in the exhaust gases. The 2.0-litre engine has different structural design details than the 113 and 827 series.In this Self-Study Programme, you can familiarise yourself with the design and function of the 113 series engine and 827 series engine with intermediate distributor drive shaft. VW has been fitting the engine with intermediate shaft in the Golf convertible since May 1999. The 2.0-litre/88 kW engine with flying camshaft (Flino) and new functional features will also be presented.233_024NewImportant NoteThe Self-Study Programme is not a Workshop Manual!Please always refer to the relevant Service Literature for all inspection, adjustment and repair instructions. Service Literature.2 Table of contents2.0-litre/85 kW engine AQY/ATU . . . . . . . . . . . . . . . 4Crankcase breather . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Fuel injection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Pistons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 PTFE oil seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Secondary air system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Emission control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 ODB II exhaust emission monitoring system . . . . . . . . . . . . . . 17 System overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Function diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Self-diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242.0-litre/88 kW engine ATF/ASU . . . . . . . . . . . . . . . 26Flying camshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 System overview ATF/ASU . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Function diagram ATF/ASU . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Service interval extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Test your knowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383 2.0-litre/85 kW engine AQY/ATUSpecifications Differences/common features233_012233_013113 series – engine AQY827 series – engine ATUSeries Engine code Type Displacement Bore Stroke Compression ratio Rated power output Torque113 AQY 4-cylinder in-line engine 1984 cm3 82.5 mm 92.8 mm 10.5 : 1 85 kW/5200 rpm 170 Nm/2400 rpm827 ATU10.0 : 1 85 kW/5400 rpm 165 Nm/3200 rpm4 Technical features Differences/common featuresAQY Engine management Lambda control Knock control Ignition system Motronic 5.9.2 Probe upstream of catalytic converter Probe downstream of catalytic converter 2 knock sensors Static high-voltage distribution with 2 twin spark ignition coils in dash panel insert with manual gearbox (EU4) only Secondary air system without secondary air injection valve Premium unleaded (RON 95) EU 4 Manual gearbox D4 Automatic gearbox 1 knock sensor Rotating distributor ATUSelf-diagnosis fault warning lamp Exhaust gas treatment Fuel Exhaust emission standardnot fittedSecondary air system with secondary air injection valve Premium unleaded (RON 95) D4 Manual gearbox D3 Automatic gearboxAQY ATUAQY ATUComparison of performance curves233_002Comparison of torque curves233_0015 2.0-litre/85 kW engine AQY/ATUEngine overview Differences/common features233_003233_004Engine AQYATU engine– AQY engine– ATU enginewithout distributor, static high-voltage distribution; engine suspension: pendulum support. with distributor, drive by means of intermediate shaft; conventional engine suspensionNotable differencesDetails of the assemblies used in both engines: – The crankshaft is mounted on 5 bearings. – The cylinder block is manufactured from gray cast iron. – The crankcase is ventilated via the cylinder head cover. – Lighter pistons reduce moving masses in the engine. – The cylinder head is made of aluminium. – The oil sump used in the AQY engine is made of aluminium and has 3 mounting points facing towards the gearbox. – The oil pump used in the AQY engine is an internal gear pump. It is driven by the crankshaft by means of a chain. The oil pump used in the ATU engine is driven via the intermediate shaft. – Spray jets for piston cooling: the ATU engine does not have a piston cooling system. – The reference marks and engine speed are registered by senders mounted on the crankshaft. – Phase recognition by Hall sender. Mounted on the camshaft in the AQY engine and on the distributor in the ATU engine.6 233_019233_005Engine AQYEngine ATUThe crossflow cylinder head is based on tried and tested structural design details. It is also used in the 1.6-litre engine with twinpath intake manifold. It offers the following advantages: – optimised intake/exhaust ports for improved handling performance and exhaust emission through a tumble duct – The intake manifold located at the front end of the engine reduces the crash impact, as there is more space between the intake pipe and the engine bulkhead. The manifold is a two-piece construction.The stainless steel exhaust manifold is a double-flow manifold. Each cylinder has its own exhaust pipe; these pipes are then paired up. The lightweight valve gear is used: – – – – 35 mm dia. hydraulic bucket tappet 33 mm dia. exhaust valves 40 mm dia. intake valves 7 mm dia. valve stemIntake valve lift: 10.6 mm Exhaust valve lift: 10.6 mm7 Crankcase breatherElectrically heatedBreather housing Intake manifoldHeating resistor233_027Task The crankcase is fitted with a breather in order to equalise the pressure difference inside the crankcase. The crankcase fills up all the way from the oil sump to the cylinder head cover. It fills up not only with oil vapour from the oil sump, but also with gases which escape from the combustion chamber by bypassing the piston rings. The pumping movement of the pistons returns this mixture of gas and oil vapour to the intake manifold via the breather in the cylinder head cover. To prevent the vapour from condensing and freezing when they enter the intake manifold during winter operation, there is an annular electrical heating resistor around the inlet. Action period The heating resistor operates continuously when the ignition is "on". Electrical circuit J17 Fuel pump relay N79 Heating resistor (crankcase breather)+30J17S243 10AN79233_0288 Fuel injectionInjector with air shroudThe ATU engine has no air-shrouded injectors!Pressure regulator Fuel railInjectorfrom intake pipe233_029Air pipe Fuel feedA single injector is assigned to each cylinder. The four injectors are inserted into the fuel rail at the top and into the engine intake manifold at the bottom. Fuel flows through these injectors from top to bottom according to the so-called “top-feed” principle. The injectors have an additional air shroud which improves mixture preparation. An air pipe is connected to the intake pipe. Each injector is, in turn, connected to the air pipe. The vacuum in the intake manifold draws air out of the intake pipe. This air is then fed to each individual injector along the air pipe. The fuel and air molecules interact in such a way that the fuel is finely atomised. The air shroud is mainly effective in the partthrottle mode of the engine.Air supply from air pipeAir shroud233_030Advantages: Combustion is improved. Pollutant emissions in the exhaust gas are reduced.9 PistonPiston design Lightweight aluminium pistons are used. They have a shortened, graphitised shaft and the bearings for the piston pins are offset inwards. The piston is box shaped. A shorter - and therefore lighter - piston pin can be used. There is a recess in the base of the piston. Over and above the advantages of lighter piston and piston pin construction, the piston has a relatively narrow slip face. The piston shape necessitates a defined installation position. This position is marked by an arrow on the base of the piston (pointing towards belt pulley).Graphite contact faceShortened shaft233_031Box shapePiston cooling To cool the piston more rapidly, a small amount of the lubricating oil in the circuit is diverted to the piston. For this purpose, each cylinder has an oil spray nozzle which is securely bolted to the cylinder block and supplied with oil directly from the oil pump via an oil duct. The oil spray nozzle has a pressure relief valve which opens at a pressure of 0.25 to 0.32 MPa. The lubricating oil is fed into the interior of the piston and cools the piston down.233_032Oil spray nozzle with pressure relief valveThe ATU engine has no oil spray nozzle for piston cooling.233_03310 SensorsHall sender G40The Hall sender is located behind the valve timing gear. The measuring wheel is secured to the back of the valve timing gear. Signal utilisation The position of the camshaft is determined via the signal from the Hall sender. The Hall sender also acts as a quick-start sender.233_034Valve timing gear Measuring wheelFunction and design Two measuring windows on the measuring wheel are wide and two measurement windows are narrow. A characteristic signal pattern is generated for each 90o crankshaft rotation. In this way, the engine control unit can determine the position of the camshaft and control the fuel injection and ignition sequences before the engine has completed half a revolution (quickstart sender). Cold-starting is improved. There is less exhaust emission during the cold start process. Substitute function and self-diagnosis If the Hall sender fails, the engine continues to run and utilises a substitute signal for this purpose. The ignition advance angle is retarded as a safety precaution. The sensor is tested during the self-diagnosis procedure. Important The ATU engine has a rotating ignition distributor which is driven by means of the intermediate shaft. The Hall sender and rotor ring are located in the distributor.Hall sender Rotor ring Measuring wheel with measurement window233_035Hall sender233_036233_00611 PTFE oil sealThe crankshaft and camshaft oil seals are radial Polyt t etraf f luoroethylene). oil seals made of PTFE (P PTFE is also known under the name Teflon and is a type of heat resistant and non-wearing plastic. These oil seals provide improved sealing from the inside and protect the engine against abrasion and dust from the exterior. The sealing lip has a hydrodynamic recirculation feature. Outer diameter ribs allow the oil seal to be fitted more securely in the crankcase. The design and material require new auxiliary tools to reliably install this new seal generation, as well as different fitting characteristics.Ribs on outer diameter233_037Sealing lip with hydrodynamic recirculation featurePTFE oil seals are dry fitted. The sealing plugs of the crankshaft/camshaft must be grease free. PTFE oil seals are always fitted in fixed directions (right and left rings).Dust lipCrankshaft journalPlease also refer to the detailed installation instructions given in the Workshop Manual for the 2.0-litre/85 kW Engine, Mechanicals.233_03812 Secondary air systemThe secondary air systems used in both engines are not identical. The secondary air control valve can only be found in ATU engine.In the AQY engine, the combination valve is opened directly by the pressure exerted by the secondary air pump and closed off from the engine by a spring.5 p 6 p 42t°13233_008Secondary air system - activatedStarting situation During the cold starting phase of an engine, the pollutant emissions (non-combusted hydrocarbons) are relatively high on account of the fact that the catalytic converter has not yet reached its operating temperature. The secondary air system helps to reduce the pollutant emission during this phase. The exhaust gas is enriched with oxygen through the injection of additional (secondary) air. The non-combusted exhaust gas constituents (carbon monoxide (CO) and hydrocarbons (HC)) are now thermally combusted. Secondly, the catalytic converter reaches its operating temperature more quickly through the heat generated by secondary combustion.System design The secondary air pump -2- blows additional air from the air filter -1- directly behind the exhaust valves when the engine is started. The system works on the basis of interaction between the following system components: – – – – – Engine control unit -3Secondary air pump relay -4Secondary air pump -2Secondary air control valve -5Combination valve -6-Input variables for the engine control unit are the coolant temperature -to- and the lambda control -λ-.13 Secondary air system5 6p 42t°13233_009de-energised Secondary air system - not activatedFunctional description The secondary air system is active in two operating states and for a limited period of time only: – cold start – in idling mode after warm start, for self-diagnosis The secondary air system is activated by the engine control unit according to the prevailing operating conditions. State Coolant temperature +5 to 33oC up to max. 96˚C Period activated 100s 10sThe secondary air pump receives its voltage via the secondary air pump relay. The engine control unit also activates the secondary air inlet valve via which the combination valve is actuated by means of partial pressure "p“. The secondary air pump injects air downstream of the exhaust valves into the exhaust gas stream for a short period of time. When the secondary air pump is inactive, the hot exhaust gases are also present at the combination valve. The combination valve seals the exhaust gases off from the secondary air pump. During the activation procedure, the selfdiagnosis checks the system. The lambda control must be active during the self-diagnosis procedure because the increased oxygen content in the exhaust gas reduces the probe voltage. When the secondary air system is intact, the lambda probes must register an extremely lean mixture.Cold start Warm start Idling14 Emission controlWhy is a second lambda probe necessary?Lambda probe G39 upstream of primary catalytic converterCatalytic converterLambda probe connections to the vehicle electrical systemLambda probe G130 after catalytic converter233_039The position of the lambda probes in the exhaust system is very important for emission control as they are subjected to heavy soiling in the exhaust gas. A probe located downstream of the catalytic converter is less prone to soiling. A lambda control system with only one probe downstream of the catalytic converter would be too slow because of the longer gas flow times.However, the more stringent exhaust emission regulations require quick and precise lambda control. A second lambda probe (with heating) therefore was installed in the exhaust system downstream of the catalytic converter (G130) in addition to the probe upstream of the catalytic converter (G39). This probe serves to check for proper functioning of the catalytic converter. The probe upstream of catalytic converter (G39) is also adapted.15 Emission controlG28 G39 G70 G130 UG39 UG130 UV Engine speed sender Lambda probe upstream of catalytic converter Air-mass flow meter Lambda probe downstream of catalytic converter Probe voltage, lambda probe upstream of catalytic converter Probe voltage, lambda probe downstream of catalytic converter Control voltage, injectorsUV U G39 U G130G70 G28 G39 G130Intake airEngine Catalytic converter Exhaust gasFuelJ220233_040The signals for air mass and engine speed are the basis for the injection signal (Uv). The engine control unit calculates the additional injection time correction factor (increase/ decrease) for lambda control from the signal supplied by the lambda probe. The lambda factor is regulated on the basis of continuous data interchange. The lambda map is still stored in the control unit memory. This map specifies the various engine operating states. Using a second closed control loop, the shift in the voltage curve corrected within a defined window (adaption) ensuring long-term stability of the mixture composition. The probe downstream of the catalytic converter has priority over the probe upstream of catalytic converter.The 2nd probe simultaneously checks the degree of conversion (a measure of cleaning efficiency) of the catalytic converter. The engine control unit compares the probe voltage UG39/probe upstream of the catalytic converter and UG130/probe downstream of the catalytic converter. If the ratio deviates from the setpoint, this is registered as a catalytic converter malfunction and stored as a fault. The voltage curves of both probes can be checked in the self-diagnosis. Effects of malfunction If the probe upstream of catalytic converter fails, lambda control is not performed. The adaption function is disabled. Emergency operation via a map-based open control loop. If the probe downstream of the catalytic converter fails, lambda control is still performed. The function of the catalytic converter cannot be checked.16 ODB II exhaust emission monitoring systemMalfunctions and defective components in the engine management system can lead to a dramatic increase in pollutant emissions. The OBD was introduced in order to avoid this. The OBD is a diagnostic system which is integrated in the vehicle's engine management system and continuously monitors the exhaust emission levels. The Motronic 5.9.2 of both 2.0-litre engines meets these requirements. The driver is informed about non-conforming exhaust emission levels by a warning lamp (exhaust gas warning lamp K83) only in vehicles with the AQY engine in combination with a manual gearbox.OBD On-Board Diagnose5.9.2 Motronic233_014Electrical circuit The warning lamp is integrated in the dash panel insert, directly connected to the engine control unit and registered by the fault memory. Like all warning lamps, the exhaust gas warning lamp lights up for several seconds when the ignition is turned on. If it does not go out after starting the engine or lights up or flashes while travelling, there is a fault in the engine electronics or certain exhaust emissions are too high. For the customer, this is a sign to take the vehicle to a service workshop. – Lamp flashing: There is a fault which can damage the catalytic converter in this vehicle operating state. The vehicle may still be operated, but only using less power. – Lamp lit continuously: There is a fault which adversely affects emission levels.3 2 141/min x 10005 6 760 40 20100 80120km/h140 160 180 200 220 240233_007J28532K83See also SSP 175.17J220233_04117 System overviewMotronic 5.9.2 The new Motronic 5.9.2 implements technical improvements for starting of the engine, lower fuel consumption and exhaust emission control. It meets the requirements of OBD II. Pollutant emissions are checked continuously. Diagnoses relevant to exhaust emissions are displayed using the readiness code.Engine speed sender G28Hall sender G40Hall sender G40 in the distributor Hot film air mass meter G70 and intake air temperature sender G42 Air-mass flow meter G70 Intake manifold temperature sensor G72 Throttle valve control unit J338 with idling speed switch F60 Throttle valve potentiometer G69 Throttle valve positioner potentiometer G88CAN-Bus HLambda probe downstream of catalytic converter G130 Coolant temperature sender G62 Knock sensor I G61Knock sensor II G66 Auxiliary signals: air conditioner compressor On A/C ready Road speed signal18CAN-Bus LLambda probe G39 In the Motronic 5.9.2 systems used the both engines, several components are different. Differences: * AQY only ** ATU onlySee also table with heading "Differences and Common Features“Control unit for Motronic J220Self-diagnosis fault warning lamp K83 Fuel pump relay J17 Fuel pump G6Injectors N30 to N33Ignition transformer N152Activated charcoal filter system solenoid valve 1 N80Throttle valve control unit J338 with throttle valve positioner V60Lambda probe heating Z19 Diagnostic connection Lambda probe 1 heating, after catalytic converter Z29Secondary air inlet valve N112 Secondary air pump relay J299 and secondary air pump motor V101233_010Auxiliary signals: Air conditioner compressor Off Fuel consumption signal19 Function diagramEngine AQYJ17 4DST56STZ19G39 Z29G130 N80G42/G70N112λN30 + N31 N32 N33λ14 A J220+M V60 F60 G88 J338 G69K83CAN - BUS HCAN - BUS LG40G28MG631Please refer to Page 33 for a legend of the function diagram. 20 D/+15+30D/+30E45 31 F47 J299 V101 4MF2N79F361G66 G61234G62N152IIVIIIIIQ P31inout233_01121 Function diagramEngine ATU30 15SJ17 12DST56STZ19G39Z28/G108 N80G72G70λN30 + N31 N32 N33λ14 A J220-M V60 F60 G88 J338 G69K83CAN - BUS HCAN - BUS LG28GG6M31Please refer to Page 33 for a legend of the function diagram. 22 30 15SXE45 31 F47 N112 J299 V101 4MFN79F36X1G66234G62 G40 N152 N157Q P31inout233_01523 Self-diagnosisThe readiness code The readiness code is an 8-digit numeric code which indicates the status of the exhaust emission diagnoses. The diagnoses are performed at regular intervals during normal vehicle operation. The readiness code does n o t indicate whether there are any faults in the system. It indicates whether certain diagnosis have been terminated -0- or have not been performed yet, or have been cancelled -1-. If the engine management system has registered a fault and stored this fault in the fault memory, the fault message can only be obtained with a fault reader.202_002The readiness code can be read out using the Vehicle Diagnostic, Testing and Information System VAS 5051 or the V.A.G Diagnostic Unit using function “15” which can be accessed via address word “01”. The readiness code can also be generated by performing a short test.Relevance of the 8-digit numeric block to the readiness codeReadiness code The readiness code for both engines is identical.The readiness code is only generated when all the digit positions on the display are 0.12345678 0 Catalytic converterDiagnostic function0Catalytic converter heating (diagnosis function currently inactive/always “0”)0Activated charcoal canister system (fuel tank purging system)0Secondary air system0Air conditioning system (diagnosis function currently inactive/always “0”)0Lambda probe0Lambda probe heater (diagnosis function currently inactive/always “0”)0Exhaust gas recirculation (not existent/always “0”)24 The Motronic 5.9.2 control unit has a fault memory. The self-diagnosis function monitors all the colour-coded parts of the system. The self-diagnosis procedure can be performed using the Vehicle Diagnostic, Testing and Information System VAS 5051 or the V.A.G Diagnostic Unit. The self-diagnosis procedure is initiated with the address word 01 - Engine electronics. The following functions are possible: 01 - Interrogate control unit version 02 - Interrogate fault memory 03 - Actuator diagnosis 04 - Basic adjustment 05 - Erase fault memory 06 - End of output 07 - Encode control unit 08 - Read data block 10 - Adaption 11 - Login procedure 15 - Read out readiness codeCAN-Bus LCAN-Bus H233_018Function 04 - Basic adjustment must be executed after changing the engine control unit, the throttle valve control part or the engine and after disconnecting the battery. Advise your customers to visit a workshop to have basic adjustment performed after replacing the battery themselves or after disconnecting and connecting the battery.202_002For the various individual fault codes, please refer to the Workshop Manual for Motronic Injection and Ignition System (2.0-litre engine).25 2.0-litre/88 kW engine ATF/ASUThe 2.0-litre/88 kW Flino engine is described below. Flino stands for "flying camshaft“. The engine will be used in A-platform vehicles, in which it will be mounted transversely, and in the Passat, in which it will be mounted longitudinally. The improved version of the 2.0-litre engine includes the following characteristic modifications: – Adjustment of the intake cam – The system components for service interval extension (new engine oil, engine oil level sensor and engine oil temperature sensor) – Twin-path intake manifold – Electric throttle drive The engine-specific requirements relating to service interval extension and camshaft timing control are described.Technical features – Engine management system Transversely mounted engine: Bosch Motronic ME 7.5 Longitudinally mounted engine: Simos 3.2 – Electronically controlled sequential injection and mapped ignition with cylinder-selective knock control – 2 valves per cylinder – 2 lambda probes; Syncro: 4 lambda probes – Secondary air system – Air-shrouded injectors – Twin-path intake manifold – Electrical throttle control – Exhaust gas monitoring (OBD II) – EU IV compliant233_01226 100200 190 180 170 160 150 140 130 120 M (Nm)233_021Specifications Code:ATF (transversely mounted), A-platform ASU (longitudinally mounted) Passat Type:4-cylinder in-line engine Displacement:1984 cm3 Bore:82.5 mm Stroke:92.8 mm Compression ratio:10 : 1 Firing order:1 - 3 - 4 - 2 Rated output:88 kW (120 bhp) Torque:175 Nm Fuel:RON 95 unleaded RON 91 unleaded (reduced power and torque)27 Overhung-mounted camshaftCamshaft timing controlRotation angleThe camshaft timing control operates mechanically with the intake cam overhung mounted. This camshaft – code designation Flino – allows rpm-dependent intake closure. Advantages: Better torque delivery across the entire rev band, higher fuel economy and improved elasticity.Direction of rotation Intake cam, variableRollerOil cushionOil bore Camshaft body233_04250 40 (degrees crankshaft after DBC) 30 20 10 0 -10 -20 1000 2000 3000 4000 5000 6000 Intake port - closing - position in dependence on engine speedIntake port closesRigid camshaft Variable camshaft233_043Function The opening action at the intake valve is no different to that on a rigid camshaft. During the closing action, however, the cam becomes twisted under the spring pressure exerted by the valve spring. The rotation angle of the intake cam is dependent on engine speed. At low engine speeds, the rotation angle is greater than at high engine speeds.28 Please refer to SSP 229 for more detailed information.Camshaft body Fitting key Roller Fitting key Bush Intake cam Bush Spring Exhaust cam Bush Intake cam Exhaust cam Function Camshaft 85 kW engine The shaft, intake cam and exhaust cam are a single part 88 kW engine A camshaft body with one oil bore aligned longitudinally and transversely in relation to the intake cam. Exhaust cam with fitting key securely connected to the body. Intake cam mounted rotatably on body. An inserted roller drives the cam and limits the angle of rotation. Oil pressure is applied to the empty space in the cam above the camshaft body. The oil cushion dampens the rotary motion and absorbs noise.233_044AdjustmentnoneThe intake cam is turned depending on engine speed. It rotates under the force exerted by the valve spring in the direction of rotation of the camshaft, but more quickly than the camshaft itself rotates. The cam "flies" ahead of the camshaft.TimingThe exhaust port and intake valve have fixed timingsThe exhaust valve has a fixed timing The intake valve has a fixed timing for the start of the opening movement and a variable timing for the end of the opening movement.29 System overview - ATF/ASUEngine speed sender G28Hall sender G40Hot film air mass meter G70 and intake air temperature sender G42 Throttle valve control unit J338 (EPC positioner) Angle senders for throttle valve drive G187 and G188 Accelerator position senders G79 and G185Lambda probe G39CAN-Bus +Lambda probe after catalytic converter G130Coolant temperature sender G62 Knock sensor I G61 Knock sensor II G66 Clutch pedal switch F36 Brake light switch F and brake light switch F47 Auxiliary signals: Air conditioner compressor ON A/C ready Road speed signal 30CAN-Bus - ATF = J220 control unit Motronic ME 7.5 ASU =J361 control unit Simos 3.2Self-diagnosis of fault warning lamp K83Fuel pump relay J17 Fuel pump G6Injectors N30 … N33Ignition transformer N152Activated charcoal filter system solenoid valve 1Throttle valve control part J338 with throttle valve drive G186Lambda probe heating Z19 Diagnostic connection Lambda probe heating 1 after catalytic converter Z29 Intake manifold change-over valve N156 Secondary air pump relay J299 and secondary air pump motor V101 Auxiliary signals: Air conditioner compressor OFF EPC fault indicator lamp Cruise control system Fuel consumption signal 31233_023 Function diagram - ATF/ASUJ17 4DST56STZ19G39 Z29G130 N80G42/G70λN30 + N31 N32 N33λ14 AJ220/J36M + +G187G188 J338G186G79/G185G40G28MG63132 D/+15+30D/+30J240 E45 31 F47 J299 V101 4MFN79N156F36361K83CAN - BUS HCAN - BUS L1234N152G66G61G62IIVIIIIIQ P31inout233_02533 Legend for Function Diagrams The Function Diagram represents a simplified current flow diagram. It contains information on the links between the Motronic 5.9.2 engine management system for the 2.0 l/85 kW (code AQY or ATU) and 2.0 l/88 kW (code ATF or ASU) engines and the Motronic ME 7.5 or Simos 3.2 engine management system.G6 G28 G39 Fuel pump Engine speed sender Lambda probe (upstream of catalytic converter) G40 Hall sender G42 Intake air temperature sender G61 Knock sensor I G62 Coolant temperature sender G66 Knock sensor II G69 Throttle valve potentiometer G70 Air-mass flow meter G72 Intake manifold temperature sender G79 Accelerator pedal position sender G88 Throttle valve positioner Potentiometer G108 Lambda probe II G130 Lambda probe (downstream of catalytic converter) G185 Accelerator pedal position sender -2G186 Throttle valve drive (electric throttle operation) G187 Throttle valve drive angle sender -1G188 Throttle valve drive angle sender -2J17 Fuel pump relay J220 Motronic control unit J299 Secondary air pump relay J338 Throttle valve control unit J361 Simos control unit K83 Self-diagnosis fault warning lamp N30...33 Injectors N79 Heating resistor (crankcase breather) N80 Activated charcoal filter system solenoid valve 1 N112 Secondary air inlet valve N122 Output stage N152 Ignition transformer N156 Intake manifold change-over valve N157 Ignition transformer output stage O Distributor P Spark plug socket Q Spark plugs S Fuse ST Fuse carrier V60 Throttle valve positioner V101 Secondary air pump motor Z19 Heater for lambda probe (upstream of catalytic converter) Z28 Heater for lambda probe 2 Z29 Heater for lambda probe 1 (downstream of catalytic converter)Auxiliary signals 1 2 3 4 5 6 Air conditioner compressor On/Off A/C ready (in) Road speed signal Fuel consumption signal Rotary latch switch, driver's door AirbagColour codes/Legend = Input signal = Output signal = Battery positive = GND = Bidirectional = Diagnostic connectionParts A D E45 F F36 F47 F60 Battery Ignition switch CCS switch Brake light switch Clutch pedal switch Brake pedal switch for CCS Idling speed switch Maintenance interval extensionSystem components for service interval extensionThe 88 kW engine has technical features which extend the vehicle's maintenance intervals. This has both economical and ecological benefits. In addition to the new engine production technology (reduced bearing clearance, precision honing), these features include a new type of oil and an engine oil sensor. Customers can fully utilise the period up to the next service in accordance with their individual driving style and conditions of use. The oil level and service requirements are indicated to the customer visually.Oil grade VW 50300Engine oil sensorBrake pad wear indicatorBattery maintenancefree (lead-calcium)New elementsService interval extension New service3 2 1 41/min x 10005 6 760 40 20100 80120km/h140 160 180 200 220 240Flexible service interval display Oil level calculated fromNew evaluation andMileage (km) reading Oil temperature Fuel consumptioninformation233_04534 The LongLife engine oilThis oil is a specially developed, non-ageing quality multi-purpose oil which conforms to the VW standard. It can be used as an all-weather oil–except in extremely cold climatic zones–withstands higher loads for longer and is of a higher grade than conventional oil. First Fill Service: VW 50300 The oil change interval within the service interval extension service is 2 years or max. 30,000 km for the 2.0-litre petrol engine The exact point in time at which the oil change takes place varies from one vehicle to another. The oil change interval is determined as a factor of fuel consumption, driving style and oil temperature and is indicated on the dash panel insert. Fuel consumption is reduced by 3%. Oil change intervals233_046– These engine oils are the prerequisites for service interval extension. Only these oils should be used to refill the engine. – No more than 0.5 litres of a different oil type may be mixed with these engine oils. See also SSP 224.35 Maintenance interval extensionSender for oil level/temperature G266 (engine oil sensor)The sender for oil level/temperature is installed at the bottom of the engine oil sump. When the ignition is turned on, filling level and temperature data are acquired continuously. These data are sent to the control unit for the display unit in the dash panel insert in the form of an output signal. Here, they are processed together with other input variables for the flexible Service Interval Display. In addition to oil level and oil temperature, fuel consumption in l/h per cylinder, the mileage reading and bonnet opening (via the bonnet contact) - as an attribute of an oil refill - are used for the flexible Service Interval Display. The present condition of the engine oil in the vehicle is determined in the dash panel insert by evaluating these influencing factors. The upper limit values are variably adapted until the next service. The system indicates to the driver that the next oil service is due 3,000 km before the next service interval elapses.233_047J218 +15G2663131233_048G266Sender for oil level/temperature J218Control unit for display unit in dash panel insertOil level indicator The conventional warning lamp for engine oil pressure is also used as an oil level indicator. If the yellow LED is continuously on = oil level too low If the yellow LED is flashing = sender for oil level defective An excessively high oil level is not indicated. 36233_049 Filling level sensorTemperature sensor3 2 141/min x 10005 6 760 40 20100 80120km/h140 160 180 200 220 240+Temperature Filling levelG266Signal waveform and evaluation The measuring element is briefly heated via the present oil temperature (output = High) and then cools down again (output = Low). This procedure is repeated continuously. The High times are dependent on the oil temperature and the Low times are proportional to the filling level. Oil level233_050The oil level can be calculated in mm from the cool-down time during the cool-down phase by means of a sensor equation. The calculation is accurate to approx. ± 2 mm. The more oil there is in the oil sump, the quicker the sensor will cool down again. Long cool-down time = low oil level Short cool-down time = normal Oil temperature During the cool-down phase of the sensor, the oil temperature signal is also transmitted.Heating phaseOil temperature evaluation 25 - 85 msHighLow Cool-down phase 200 - 1,000 ms233_02637 Test your knowledgeWhich of these answers is/are correct? Sometimes only one answer is correct. However, more than one or all of the answers may be correct. Please fill in the gaps. 1. The position of the camshaft in the AQY engine is indicated by Hall sender G40. It has A. B. C. a measurement window with the same width for each cylinder, four different measurement windows, two narrow measurement windows and two wide measurement windowswhich generate a characteristic signal for each 90o crankshaft rotation .2.The injectors of the AQY engine are A. B. C. identical to those used in the 1.6-litre and 1.8-litre engines. also fitted with an air shroud. of the so-called “top feed” type.3.The crankcase has a breather to compensate for pressure differences. The mixture of gas and oil vapour is ………………………… recirculated. To prevent the mixture condensing on entry, the inlet is heated. This process takes place A. B. C. throughout winter operation. continuously when the ignition is "on". during the starting cycle (much like a diesel glow plug).4.By injecting additional air (secondary air) into the exhaust gas,the pollutants in the exhaust gas are recombusted. As a result, A. B. C. the catalytic converter reaches its operating temperature quickly. the pollutant components CO and HC are reduced. the engine runs with an air surplus.5.The secondary air system is A. B. C. D. continuously active. only active during the cold start phase. active during the cold start phase and in the idling phase after a warm start. featured in both engines.38 6.The combination valve in the secondary air system on the ATU engine A. B. C. is activated electro-pneumatically by the engine control unit. is a vacuum controlled pneumatic valve. is a pneumatic valve which is activated by a separate electro-pneumatic valve.7.The advantages of the twin-probe lambda control are: A. B. C. Quick and precise lambda control. The conversion efficiency of the catalytic converter is checked. Malfunctioning of the catalytic converter is detected by comparing the probe voltages with a setpoint.8.The readiness code A. B. C. indicates that diagnoses are in progress to ensure vehicle operation in conformity with the prescribed emission limits. indicates faults in the exhaust emission control system. can be generated and read out.9.The new Motronic 5.9.2 is a generation of engine control units featuring A. B. C. technical improvements for starting the engine, low fuel consumption and reduced exhaust emission. technical control systems for intake air temperature stabilisation. meeting the requirements for OBD II.10 .The ATU and AQY engines have different A. B. C. distributors. engine mounts. numbers of knock sensors.1. C.; 2. B., C.; 3. in the intake manifold, B.; 4. A., B.; 5. C., D.; 6. C.; 7. A., B., C.; 8. A., C.; 9. A., C. 10. A., B., C. Solutions 39 Service.233For internal use only © VOLKSWAGEN AG, Wolfsburg All rights reserved. Technical specifications subject to change without notice. 940.2810.52.20 Technical status: 08/99❀ This paper is produced fromnon-chlorine-bleached pulp.