TECHNICAL DOCUMENTATION

SSP 303 The V10-TDI engine

PDFEN48 pages3 MB
SSP 303 The V10-TDI engine - PDF cover

This PDF is currently unavailable.

Read document text
Service.Self-Study Programme 303The V10-TDI enginewith pump-jet fuel injection systemDesign and function ... Easy to recognise, the beauty of the classical lines, the calm but predominantly powerful charisma of intelligent and sensible engine activity, simple and elegant – in short, ladies and gentlemen, you can see here the world’s top performer! A milestone... ... in statuary! ... in engine development!303_U2With the V10-TDI engine, Volkswagen once again sets new standards in diesel technology. Due to a multitude of innovative techniques, the highest demands in terms of performance, torque and emissions made of a diesel motor are fulfilled for the luxury vehicle class. The V10-TDI engine crowns 25 years of diesel engine development at Volkswagen. It is the most powerful series passenger-vehicle diesel engine in the world.NEWCaution NoteThe Self-Study Programme describes the design and function of new developments! The contents are not updated.Please always refer to the relevant service literature for up-to-date inspection, adjustment and repair instructions.2 At a glanceIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Engine mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Oil circulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Coolant circulation system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Fuel system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32System overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Check your knowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463 IntroductionThe V10-TDI engineThe V10-TDI engine is a newly developed diesel engine in which innovative light-weight construction and enormous power are united within compact dimensions. It has a cylinder block made of aluminium, where the two rows of cylinders are arranged at an angle of 90o to one another. The control and ancillary unit is driven by gearwheels The tried-and-tested pump-jet fuel injection system ensures a high performance yield at low exhaust emissions. The V10-TDI engine is used as a high-performance engine in the Volkswagen Touareg and Phaeton.303_001Engine mechanics technical features – Cylinder block made of aluminium with an end bracket made of cast-iron – Joining of cylinder head and cylinder block via tie-rod screw connection – Contol and ancillary unit driven by gearwheels – Balancer shaft for reducing vibrationsEngine management technical features – Two motor controllers – Charged by two adjustable turbochargers – Exhaust gas recirculation effected with pneumatically controlled exhaust gas recirculation valves with electrically-operated intake manifold flaps – Lambda probes for controlling exhaust gas recirculationA detailed description of the engine management system for the V10-TDI engine can be found in Self-Study Programme No. 304 ”Electronic Diesel Control EDC 16”.4 Technical dataEngine code Construction Displacement Bore Stroke Valves per cylinder Compression ratio Max. output Max. torque Engine management Fuel Exhaust treatment Ignition sequence Exhaust emission standard AYH (in the Touareg) 4921 cm3 81 mm 95.5 mm 2 18 : 1 230 kW at 4000 rpm 750 Nm at 2000 rpm Bosch EDC 16 Diesel at least 49 CZ or biodiesel Exhaust gas recirculation and oxidation catalytic converter 1 - 6 - 5 - 10 - 2 - 7 - 3 - 8 - 4 - 9 EU 3 AJS (in the Phaeton)V engine, 90o V-anglePower/torque diagram260 240 220 200(kW)The V10-TDI engine develops a maximum torque of 750 Nm at a speed as low as 2000 rpm.800 700 600(Nm)180The nominal output of 230 kW is achieved at 4000 rpm.Performance (kW)160 140 120 100500 400 300 20080 6040 2005001000150020002500300035004000(1/min)4500Torque (Nm)303_002Speed (rpm)5 Engine mechanicsCylinder blockThe cylinder block consists of the top portion of the cylinder block and the end bracket. The top portion of the cylinder block is manufactured from an aluminium alloy; this is a significant factor in weight reduction. The cylinder rows are positioned at a 90o angle to one other, permitting a compact design for the engine as a whole.Top portion of cylinder blockEnd bracket303_031Cylinder walls with plasma-sprayed running filmPlasma jetPlasma burnerFor the first time for diesel engines, a plasmasprayed running film is applied to the cylinder walls. As a result, the use of cylinder liners in the aluminium cylinder block is no longer necessary. This reduces the weight of the engine and permits compact dimensions due to a short distance between the cylinder bores.Cylinder wall303_069Detailled information regarding the plasma coating principle can be found in Self-Study Programme No. 252 ”The 1.4l/77 kW Engine with Direct Fuel Injection in the Lupo FSI”.6 End bracketThe two-part end bracket is manufactured from high-tensile cast-iron. The upper and lower portions of the end bracket are attached by a press fit; in addition, they are screwed together. This provides the crankshaft bearing with the required sturdiness, so that the high combustion forces can be safely absorbed in the end bracket area.End bracket, upper portionEnd bracket, lower portionEnd bracket, upper portionEnd bracket, lower portion303_077Press fit303_087Thrust bearings for the balancer shaftBolted connectionThe bolted connection of the cylinder block with the upper portion of the end bracket must not be loosened; otherwise, the cylinder block could deform. Please observe the instructions in the repair guidelines.303_0227 Engine mechanicsCylinder headThe V10-TDI engine has two aluminium-alloy cylinder heads. The inlet and outlet channels are arranged according to the crossflow principle. The inlet and outlet channels are located on the side opposite of the cylinder head. This arrangement provides good gas exchange and thus good cylinder filling. The inlet channels are located in the V space of the engine, while the outlet channels are on the engine exterior.Tie rod principle In order to prevent tension in the cylinder block, the cylinder heads, the cylinder block and the end bracket are screwed to each other using tie rods.Inlet channel Outlet channel303_025Tie rodCylinder headCylinder blockEnd bracket, upper portion Bedding of balancer shaft End bracket, lower portion303_0498 CrankshaftThe crankshaft of the V10-TDI engine is made of tempering steel. It is forged from one part. The drive wheel for the geared drive, the sender wheel for the engine speed sender and screwedon counterweights are located on the crankshaft.Drive wheel for geared driveEngine speed sender wheel303_023Split pin displacement All the cylinders of a 4-stroke engine ignite within a crankshaft angle of 720o. In order to attain uniform ignition, the ignition angle for a 10-cylinder engine must be 72o.720o crankshaft angle 10 cylinders= 72o ignition angleA 10-cylinder V-engine must therefore have a V-angle of 72o. Since the V10-TDI engine has a V-angle of 90o, the split pin must be displaced by 18o in order to attain uniform ignition. 90o V-angle - 72o ignition angle = 18o split pin displacement303_1079 Engine mechanicsPiston and connecting rodsIn order keep the demands on the piston and connecting rods low at the high combustion pressures, the piston pin bosses and the connecting rod boss have a trapezoidal shape. This distributes the combustion forces over a broader area. The piston pin bosses are also strengthened by brass bushes. A cooling channel is infused into the piston to cool the piston ring zone. Oil is injected into this cooling channel from the oil-spraying jets as soon as the piston is located in the bottom dead centre.Cooling channelBrass bush303_097Connecting rod The connecting rod and the connecting rod lid are separated diagonally; they are separated by the crack procedure.Brass bushDisplacement of the piston pin axis The piston pin axis is decentrally arranged in order to prevent noise from the tilting of the piston in the top dead centre. Each time that the connecting rod is in a sloping position, lateral piston forces occur which alternatingly press the piston against the cylinder walls. The lateral piston force changes direction in the top dead centre. The piston is tilted to the opposite cylinder wall there, thus resulting in noise. To prevent this, the piston pin axis is decentrally arranged. Due to the decentral arrangement of the piston pin axis, the piston changes sides before it reaches the top dead centre and then supports itself on the opposite cylinder wall.303_098Top dead centre303_09910 Mass balancingIn order to attain low-vibration running of the engine, the moments of inertia must be balanced. For this, 6 counterweights are attached to the chrankshaft. In addition, a counter-rotating balancing shaft and a weight located in the drive wheel of the balancing shaft eliminate the moments of inertia. The balancing shaft is driven by the chrankshaft; at the same time, it serves as a driveshaft for the oil pump.Counterweight Crankshaft Sender wheel for engine speed sender Vibration damper Silicone oilThe counterweights are made of a tungsten alloy. As tungsten has a high density, the weights can have small sizes, which saves space.Counterweight Balancing shaftCounterweight Drive wheel for oil pump303_008303_024Vibration damper The vibration damper reduces the rotational vibrations of the crankshaft. It is filled with a silicone oil. The rotational vibrations of the crankshaft that occur are eliminated by the shear forces of the silicone oil.11 Engine mechanicsOverall view of the geared drive with auxiliary componentsThe geared drive is located on the flywheel side. The camshafts as well as the auxiliary components are driven by the crankshaft by helic gear wheels. The advantage of gear wheels over a toothed belt is that larger forces can be transferred while the size remains the same. In addition gear wheels have no longitudinal expansion. The geared drive is maintenance-free.Coolant pumpDrive wheel for camshaftAir-conditioning system compressorCoupling with Hardy discsTra vel lingPump for power steeringdir ect ion12 AlternatorDrive wheel for camshaftBelt drive moduleCrankshaft303_01613 Engine mechanicsGeared drive assemblyDrive wheel – camshaft Cylinder bank I Drive wheel for coolant pumpDrive wheel – alternatorCompensation wheelDrive wheel – camshaft Cylinder bank IICrankshaft303_003Drive wheel – pump for power steering and air-conditioning system compressorBolted connection with bearing tunnelDrive wheel – oil pump/balancing shaft14 Belt drive module The belt drive module is a component in which helic gear wheels are positioned between two carrier plates. To ensure that all components of the belt drive module expand uniformly when exposed to heat and, as a result, to ensure that the face play is the same in all operating states, the carrier plates of the belt drive module are manufactured from tempered cast-iron. The belt drive module is connected by three screws to the bearing tunnel, which is also manufactured from cast-iron. The gearwheels are made of steel. They have a helix angle of 15o; as a result, two tooth pairs are always meshing. In comparison to spur-toothed gearwheels, larger forces can be transferred, thus providing a high smoothness of running.Oil supply line Carrier plate Carrier plate303_102Carrier plateCarrier plate303_00415 Engine mechanicsShackle jointThe drive wheels of the camshafts are connected to the geared drive by a shackle joint. The camshafts are located in the aluminium cylinder head. The carrier plates of the belt drive module are made of cast iron. As aluminium expands further when exposed to heat than does cast iron, the face play of the gearwheels must be compensated. For this purpose, a compensation wheel is positioned in a shackle joint between the camshaft wheel and the drive wheel of the belt drive module.303_045Balance pistonCamshaft gearwheel Cylinder head Shackle joint Camshaft gearwheel303_113Compensation wheelBalance pistonDrive wheelShackle303_00716 How it works When subjected to heat, the axle spacing of the camshaft to the belt drive module changes. The compensation wheel in the shackle joint follows the joint movement; the face play between the wheels within the shackle joint remains equal.Setting for ”Cold engine”Setting for ”Warm engine”Compensation wheelCamshaft gearwheelShacklesBelt drive module303_017aDrive wheel303_017bBalance pistonBalance piston The shackles of the shackle joint are tensioned by a balance piston. The piston consists of a sleeve in which several spring washers are arranged behind one another and are axially tensioned. The balance piston is screwed into the cylinder head; using a full floating axle, it tensions the two shackle joints. This prevents ”dangling movements” of the shackle joint.303_037Cylinder head SleeveSpring washers Full floating axle Balance piston Compensation wheel303_08317 Engine mechanicsAlternatorThe alternator is arranged in a space-saving manner in the V-space of the engine. It is driven by a geared drive via a transmission shaft and a Hardy disc of the geared drive. Due to the transmission shaft, the alternator speed increases by a factor of 3.6 compared to the engine speed. This provides an increased alternator performance that can cover high power demands of the vehicle electrical system even when idling. The alternator is liquid-cooled.303_046Coolant connection Alternator Power flowTransmission shaftHardy disc303_101CrankshaftGeared drive303_09518 Power steering pump/airconditioning system compressorThe power steering pump and the airconditioning system compressor are arranged in a row on the engine block. The power steering pump is driven directly by the geared drive. The air-conditioning system compressor is driven by the shared drive axis and two Hardy discs that are arranged in a row. The overload protection of the air-conditioning system compressor is implemented by a shaped rubber element.303_048Further information regarding the externally controlled air-conditioning system compressor can be found in Self-Study Programme No. 301 ”The Phaeton – Heating/Air-Conditioning System”Air-conditioning system compressorPower steering pump303_072The Hardy disc consists of a rubber body with integrated steel sleeves. It has the advantage that, due to its material elasticity, it permits small bending angles of the rotary axles and compensates for small changes in length between the connecting flanges. In addition, it has a vibration-dampening effect on torque fluctuations.Hardy discs303_09619 Engine mechanicsOil circulationShort-circuit valve Oil return baffle Oil return baffle Oil-pressure switch Oil cooler Oil filter Oil return baffleVacuum pumpPiston with cooling channelExhaust turbochargerOil-spraying jets (piston cooling) Oil separatorOil supply of the belt drive module Oil pump303_053Oil – without pressure Oil – with pressure Aspiration holeOil pressure control valvesThe oil pressure control valves control the oil pressure of the engine. They open as soon as the oil pressure reaches the maximum permitted value. The oil return baffles prevent oil from flowing back out of the cylinder head and the oil filter housing into the oil pan when the engine is at a standstill. 20The short-circuit valve opens when the oil filter is occluded, thus ensuring the oil supply to the engine. Oil supply in belt drive moduleMain channel in cylinder headMain channel in cylinder headCylinder head Oil lineOil lineOil channel in belt drive moduleOil supply from cylinder block303_054Belt drive moduleOil filter moduleThe oil filter module is located in a space-saving manner in the V-space of the engine. The oil filters, the oil filler neck and the oil cooler are integrated in the oil filter module.Oil filter moduleOil filler neck Oil filter housing303_027Oil cooler303_02821 Engine mechanicsOil pumpThe oil pump is located on the engine face in the oil sump of the oil pan. It has four pairs of toothed wheels, working according to the duocentric principle. Two of these are oil pressure pumps that generate the oil pressure that is required for the oil circulation. The other two are oil scavenge pumps that suction the oil out of the areas of the exhaust turbocharger oil returns, ensuring that there is a sufficient amount of oil in the oil filler neck in every operating state. The oil pump is driven by the geared drive via the balancer shaft.Oil pan, upper portion Oil return pipeOil pressure pumpOil scavenge pump Lines of the oil scavenge pumpsOil pressure line to engineOil separator303_093Suction lines of oil scavenge pumpsRotors of oil pressure pumpsOil separator Driving toothed wheel Rotors of oil scavenge pumps303_10022 Oil panThe oil pan consists of two cast-aluminium parts. The lines for the oil scavenge pumps are located in the upper part of the oil pan. The lower part of the oil pan contains the sender for the oil level and the wash plates that are used to calm the oil in the oil sump. The structural shape of the lower part of the oil pan differs in the Phaeton and the Touareg. The Touareg has a deeper lower part of the oil pan than the Phaeton, so that it can hold a larger amount of oil. In addition, the lower part of the oil pan of the Touareg has elastic flap traps. These prevent the oil sump from running dry when driving on inclines.Oil pan, upper portionLines of the oil scavenge pumps303_078Oil pan, lower portion – PhaetonOil pipe to oil scavenging Flap trapsOil pan, lower portion – TouaregOil pipe to oil scavengingOil level senderOil level senderWash platesWash plates303_080303_079303_082303_08123 Engine mechanicsFunctioning of the oil scavenging system in different driving states In order to ensure functioning of the compressed oil system, with the correct filling level in all driving states, two oil scavenge pumps are used. The following examples describe the oil scavenge system in three different driving states.Oil scavenge system, normal driving Compressed oil system, engine Oil returnOil return of the turbochargerOil return Geared driveOil returnCompressed oil channelOil returnOil pressure pumpsOil level normal operationOil pressure control valves Flap traps Oil separator Oil scavenge pumps Aspiration hole303_019During uniform, level driving, the two oil pressure pumps suction the oil out of the oil sump via the oil filler neck and pump it into the compressed oil system of the engine. Part of the returning oil flows directly into the oil sump of the oil pan while the rest flows from the returns of the turbocharger and of the geared drive into the rear area of the oil pan.There, the oil is suctioned off by oil scavenge pumps and returned to the oil sump by the oil separator. The oil separator works according to the principle of a cyclone. It separates the oil from the scavenged oil-air mixture before the oil flows back to the oil sump.24 Oil scavenge system, uphill driving Compressed oil system, engine Oil return303_020During uphill driving or when accelerating, the oil flows into the rear area of the oil pan. The flap traps close, thus preventing all the oil from flowing into the rear area of the oil pan. The oil scavenge pumps suction the oil out of the rear area of the oil pan. This ensures pressure-free oil return from the turbocharger and the geared drive. The scavenged oil is transported to the sump by the oil separator. This ensures the oil supply of the oil pressure pumps.Oil scavenge system, downhill driving Compressed oil system, engine Oil return303_021During downhill driving or when braking, the oil collects in the front part of the oil pan. As a result, the oil level lies above the oil filler neck, ensuring the oil supply of the oil pressure pumps. The oil returning from the turbocharger and the geared drive can flow into the oil sump via the open flap traps.25 Engine mechanicsCoolant circulation systemSystem overview1034 1416 515 2 1 8 96 7141311 12Engine coolant circulationCoolant circulation for alternator and fuel cooling (Touareg only) warm cold303_039warm cold26 1 2 3 4 5 6 7 8Cooler for engine coolant circulation Cooler for alternator/fuel cooling Pump for coolant after-run V51 Check valve Pump for fuel cooling V166 Valve body Cylinder head/cylinder block AC generator9 10 11 12 13 14 15 16Fuel cooler Compensator reservoir Circulation pump V55 Heat exchanger for heater Auxiliary water heater (auxiliary heater) Cooler for exhaust return (Phaeton only) Coolant temperature sender G62 Coolant temperature sender- cooler outlet G83Coolant circulation for alternator and fuel cooling (in the Touareg only) In the Touareg, the V10-TDI engine has a separate coolant circulation for the alternator and the fuel cooling. This is required because the temperature of the coolant is too high to cool the returning fuel when the motor is running. Circulation pump V55 The fuel cooling pump is an electrical circulation pump. If required, it is activated by the Climatronic control unit, providing the circulation of coolant in the coolant circulation for the alternator and the fuel cooling. 1. When the engine is running, the pump provides an increased flow of coolant through the heat exchanger for the heater; it also supports the functioning of the auxiliary heater. 2. The pump fulfils the duties of the residual heat function up until 30 minutes after the engine is stopped. For this purpose, it is activated by the Climatronic control unit when the driver activates the residual heat function.Pump for coolant after-run V51 The pump for coolant after-run is an electrically driven pump that is activated by the engine control unit. It fulfils two duties: 1. At low engine speeds, the pump for coolant after-run supports the mechanically driven coolant pump, thus providing for sufficient coolant circulation. 2. To carry out the coolant after-run function, the pump is activated by the engine control unit according to a characteristic map.Pump for fuel cooling V166 The fuel cooling pump is an electrical circulation pump. If required, it is activated by the engine control unit, providing the circulation of coolant in the coolant circulation for the alternator and the fuel cooling.27 Engine mechanicsCoolant pumpThe coolant pump is located on the engine face in the engine block. It is driven by the belt drive module via a connection shaft.Coolant pump303_047Driving toothed wheel in belt drive moduleConnection shaft303_075Coolant drain plugsCoolant drain plugs Two coolant drain plugs are located on the engine face in the cylinder block. When the cylinder heads or another component in the V-space of the motor is to be removed, the coolant drain plugs can be used to drain the coolant down to the level of the coolant pump.303_07628 Thermostat for characteristic mapcontrolled engine coolingThe thermostat for characteristic map-controlled engine cooling is located in the pipe union of the coolant controller housing. Its duty is to switch between the large and the small coolant circulation systems. For this, it is activated by the engine control unit according to the requirements of the engine’s operating state. Characteristic maps that contain the nominal value temperature depending on the engine load are stored in the engine control unit.303_026The advantage of characteristic map-controlled engine cooling is that the coolant temperature level can be adapted to the current operating state of the engine. This helps to reduce fuel consumption in the partial-load range and to reduce exhaust emissions.Pipe unions of coolant controller housingPipe unions of coolant controller housingCompression spring Resistance heatingElastic elementA detailed description of characteristic map-controlled engine cooling can be found in Self-Study Programme No. 222 ”Electronically Controlled Cooling System”.Stroke pin303_01529 Engine mechanicsWater connectionThe water connection is located in the V-space of the engine, above the coolant controller housing. It connects the coolant circulation of the two cylinder heads. The coolant is transported out of the cylinder heads through the two large connections to the coolant controller housing. The small connections that are further towards the top are used for ventilation.Water connection303_012Oil filter Sender for coolant temperature G62Connection – ventilationConnection – ventilationConnection – coolantConnection – coolant303_014Connection nozzleCoolant controller housing30 Removal and installation In order to permit the water connection in the V-space of the engine to be removed and installed, the two large connections in the water connection housing can be pushed in/pushed apart.Water connection – installation position Water connection housing Gasket Gasket303_013Water connection – assembly position303_10531 Engine mechanicsFuel systemThe fuel is transported out of the fuel tank to the fuel filter unit by electrical fuel pumps. The mechanical fuel pumps suck the fuel out of the fuel filter unit and transport it at high pressure into the preliminary run of the fuel manifolds. The fuel that is not required for fuel-injection is transported via the return flow of the fuel manifolds to the fuel filter unit and from there back to the fuel tank via a fuel cooler.Fuel temperature senderFuel filter unitFuel pumpFuel temperature senderReturn flow Preliminary run – low pressure Preliminary run – high pressure32 Fuel manifoldFuel cooler (in Touareg)Connection nozzleFuel cooler (in the Phaeton)303_106Pressure relief valve Fuel return flowIn the Touareg, the fuel is cooled by a fuel-coolant cooler. In the Phaeton, the fuel is cooled by a fuel-air cooler.Vacuum pump Fuel pump303_05133 Engine mechanicsPressure relief valve Fuel return flowOverall schematic diagram The electrical fuel pumps work as preliminary transport pumps, pumping fuel to the fuel filter unit. The check valves prevent fuel from flowing out of the fuel manifold and the preliminary run line back into the fuel tank when the engine is at a standstill. The fuel filter unit protects the injection system from soiling and wear by particles and water. The fuel pumps transport the fuel out of the fuel filter unit and pump it at high pressure into the preliminary run of the fuel manifolds. The pressure control valves regulate the fuel pressure in the fuel preliminary run to approx. 8.5 bar.Fuel filter unit Fuel pump Sender for fuel temperature Pressure control valveCheck valveThe pressure relief valves limit the fuel pressure in the fuel return flow to approx. 1 bar. As a result, the pressure conditions in the fuel system are balanced. The fuel temperature senders are used to record the fuel temperature for the engine control units. The preheating valve guides the fuel in the return flow into the fuel filter unit when the outside temperature is low, thus preventing clogging of the filter inserts.Check valvePreheating valveFuel pumpPressure control valveThe fuel cooler cools the fuel in the return flow to protect the fuel tank from fuel that is too hot.Sender for fuel temperaturePressure relief valve fuel return flow34 Pump-jet unitFuel manifoldCoolantFuel cooler Electrical fuel pump Fuel manifold303_088Return Preliminary run – low pressure Preliminary run – high pressure35 Engine mechanicsFuel filter unitThe fuel filter unit is located in a crash-safe position in the V-space of the engine. It contains two filter inserts and a sender for the fuel composition. The sender for the fuel composition is used to inform the driver if the water level in the filter unit is too high using an indicator light in the dash panel insert. There is a preheating valve in the lid of the fuel filter unit; when the outside temperature is low, this guides the fuel in the return flow from the engine back into the filter. In the Touareg, a coolant-fuel cooler is integrated into the fuel filter unit. It cools the fuel flowing back into the fuel tank, thus preventing damage to the fuel tank by return flow fuel that is too hot. In the Phaeton, a fuel-air cooler is located under the vehicle floor.303_029Fuel filter unitReturn flow to fuel tank Preliminary run of fuel tank Lid of fuel filter unit Fuel return flow from the pump-jet units DrainageConnection for coolantFuel preliminary run to fuel pump303_030Fuel return flow from the pump-jet units Fuel composition senderFuel cooler36 Preheating valveAt low outside temperatures, diesel fuel tends to precipitate paraffin. This can clog the fuel filter; as a result, operating the engine may no longer be possible due to a lack of fuel. To prevent this, there is a preheating valve in the lid of the fuel filter unit. Depending on the outside temperature, the preheating valve guides the fuel that is flowing back from the pump-jet units either to the fuel filters or to the fuel tank.Warm fuel temperature At a fuel temperature above 40 °C in the fuel preliminary run, the piston is pressed against the spring by the elastic element. The preheating valve completely opens the way into the fuel return flow. The fuel that is flowing back from the pump-jet units directly enters the return flow to the fuel tank. In the fuel preliminary run, the fuel is transported via filter inserts and the flatter valve to the fuel pumps.Elastic element warmLid of fuel filter unitSpring Piston303_103FilterFlatter valveto fuel pumpCold fuel temperaturecoldRetrurn flow from pump-jet unitsAt a fuel temperature below 10 °C, the elastic element contracts, so that the spring force of the piston closes the way to the fuel tank. As a result, the fuel that is flowing back from the pump-jet units is guided to the filters. The fuel in the filter unit is heated, thus preventing clogging of the filters.Return flow to fuel tankPreliminary run of fuel tank303_10437 Engine mechanicsPump-jet unitsThe pump-jet units that have already been installed in the 1.9l/74 kW TDI engine are used in the V10-TDI engine. They are characterised by: – a low-friction drive – an increased injection pressure in the partial load range – a compact solenoid valve To provide a low-friction drive, the adjusting screw is equipped with a rounded end while the stud is provided with a ball socket. Due to the large radii, the surface pressure is low. In addition, the engine oil can collect in the ball socket, thus ensuring good lubrication between the adjusting screw and the stud. In the partial load range, the injection pressure is increased by an alternative piston with a large stroke. Due to the large stroke of the alternative piston and the throttling effect of the inflow hole between the jet spring space and the fuel channel, the pressure in the jet spring space increases. The jet springs are further prestressed, thus increasing the injection pressure.Solenoid valve Adjusting screwStudAlternative pistonInflow holeJet spring303_01038 Exhaust systemThe exhaust system of the V10-TDI engine consists of one preliminary catalytic converter and one main catalytic converter per cylinder bank, as well as a preliminary silencer and a main silencer. All catalytic converters are oxidation catalytic converters. The preliminary catalytic converters are located near the engine so that the operating temperature can be quickly attained, ensuring a high degree of pollutant reduction. The lambda probes located in front of the preliminary catalytic converters are used to control exhaust gas recirculation.Lambda probe G39 Lambda probe G108Preliminary catalytic converterThe representation in the figure corresponds to the exhaust system in the Touareg.Main catalytic converterRear silencerPreliminary catalytic converter Main catalytic converterPreliminary silencer303_03339 System overviewOverview of engine managementEngine speed sender G28Sender for accelerator pedal position G79 Kickdown switch F8 Idling switch F60Air mass flow meter G70Hall sensor G40 Coolant temperature sender G62Coolant temperature sender, cooler outlet G83Fuel temperature sender G81Fuel composition sender G133Load pressure sender G31 Sender for intake air temperature G42Lambda probe G39Brake light switch F Brake pedal switch F47Additional input signals40 This section provides you with an overview of the V10-TDI engine management system. A detailed description of the sensors, actuators and functions of engine management can be found in Self-Study Programme No. 304 ”Electronic Diesel Control EDC 16”.Height senderValve for pump/jet N240 - N244Engine control unit 1 J623Fuel pump relay J17 Fuel pump (preliminary transport pump) G6 Fuel pump G23 Servomotor for exhaust turbocharger 1 V280 Exhaust gas recirculation valve N18Diagnostics connectionMotor for intake pipe valve V157Servomotor for exhaust turbocharger 2 V281Thermostat for characteristic mapcontrolled engine cooling F265Relay for coolant after-run J496 Water pump V51Engine control unit 2 J624 Relay for pump, fuel cooling J445 Pump for fuel cooling V166Valve for pump/jet N245, N303 - N306Air mass flow meter 2 G246Exhaust gas recirculation valve 2 N213Cooler change-over valve, exhaust gas recirculation N345Fuel temperature sender 2 G248Motor for intake pipe valve 2 V275Solenoid valve for electrohydraulic automotive bearing control unit N145Sender 2 for intake air temperature G299 Load pressure sender 2 G447Cooler change-over valve 2, exhaust gas recirculation N381Heater for lambda probe Z19Lambda probe 2 G108Heater for lambda probe Z28Heater plug relay J52 Heater plugs Q10 - Q14Heater plugs Q15 - Q19 Heater plug relay 2 J495303_036Additional output signals ServiceSpecial toolsDesignation T10191 frame Tool Usage To switch off the V10-TDI engine303_056T10192 oil filter keyRemoval and installation of the oil filter lid303_057T10193 camshaft clampTo fasten the camshaft cylinder bank 1 when setting the control times303_058T10194 camshaft clampTo fasten the camshaft cylinder bank 2 when setting the control times Removal and installation of the oil filter module303_05942 Designation T10195 crankshaft clampToolUsage To fasten the crankshaft when setting the control times303_060T10196 keyTo install the PTFE crankshaft gasket on the flywheel side303_061T10197 plug cartridge SW6For removal and installation of various add-on pieces in the V-space of the engine303_062T10198 plug cartridge XZN16For removal and installation of the camshaft wheel303_06343 ServiceDesignation T10199 clamping deviceToolUsage Clamping the camshaft wheels to remove and install the camshaft wheels303_064T10200 guide pinFor removal and installation of the belt drive moduleFigure was not available at the copy deadlineT10201 clamping device Figure was not available at the copy deadlineFor removal and installation of the bearing tunnelT10202 keyFor removal and installation of the fuel transport unit303_06744 Designation T10126 transport shackleToolUsage To transport the V10-TDI engine with workshop crane VAS 6100303_108T10207 assembly equipmentTo install the PTFE crankshaft gasket on the gearbox side303_109T10208 assembly equipmentTo install the PTFE crankshaft gasket on the alternator shaft303_110T10210 calibre Figure was not available at the copy deadlineTo align the pump-jet units45 Check your knowledgeWhich answers are correct? Sometimes only one. Sometimes more than one – or all of them!1.The cylinders of the V10-TDI engine have … A. B. C. a plasma-sprayed cylinder wall. wet cylinder liners. dry cylinder liners.2.Why are the counterweights on the crankshaft made of tungsten? A. B. C. Tungsten has a high density, so that the weights can be small, thus saving space. Tungsten has a high temperature stability. Tungsten is inexpensive.3.How are the auxiliary engines of the V10-TDI engine driven? A. B. C. D. using a toothed belt drive using spur-toothed gearwheels using helic gearwheels using a chain drive4.What advantages do gearwheels have over toothed belts? A. B. C. Gearwheels are lighter, thus reducing weight. Gearwheels can transfer higher forces per unit size. Gearwheels have a greater longitudinal extension.5.What is the duty of the shackle joints? A. B. C. They compensate for the tooth play between the camshaft wheel and the drive wheel of the belt drive module. They change the control times under full-load operation. They increase the camshaft speed when idling.46 6.What is the duty of the oil scavenge pumps? A. B. C. They generate the oil pressure that is required for the oil circulation of the engine. They suction the oil out of the exhaust turbocharger oil return flow. They ensure that a sufficient quantity of oil is in the oil filler neck in every operating state.7.How is fuel transported from the mechanical fuel pumps to the pump-jet units in the V10-TDI engine? A. B. C. using fuel manifolds using holes in the cylinder head using flexible steel hoses8.Which statement is correct? A. B. C. In the Phaeton, the return-flow fuel is cooled by a fuel-air cooler under the vehicle floor. In the Touareg, the return-flow fuel is cooled by a fuel cooler that is integrated in a separate coolant circulation. The return-flow fuel is not cooled.1. A.; 2. A.; 3. A., C.; 4. B.; 5. A.; 6. B., C.; 7. A.; 8. A., B. Solutions 47 Service.303For internal use only © VOLKSWAGEN AG, Wolfsburg All rights reserved. Technical specifications subject to change without notice. 000.2811.23.20 Technical status 09/02❀ This paper was produced fromchlorine-free chemical pulp.