TECHNICAL DOCUMENTATION

SSP 305 The 2,5 l R5 TDI engine

PDFEN36 pages1 MB
SSP 305 The 2,5 l R5 TDI engine - PDF cover

This PDF is currently unavailable.

Read document text
Service.Self-study programme 305The 2.5 l R5 TDI engineDesign and function The 2.5 l 5-cylinder in-line TDI engine with pump injection system represents a new generation of 5-cylinder diesel engines. The primary development goal was to use the engine in various models (transverse and longitudinal mounting) with a high power density.The engine is used in the Transporter 2004 with an output of 96 kW and 128 kW, and in the Touareg with an output of 128 kW. The engines in the Transporter 2004 and in the Touareg differ particularly in respect to their adaptations for transverse and longitudinal mounting.305_018305_038Transporter 2004 – transverse mountingTouareg – longitudinal mountingWe will present to you the design and function of the new 2.5 l R5 TDI engine on the following pages.NEWImportant NoteThis self-study programme shows the design and function of new developments! The contents will not be updated.For the latest testing, adjustment and repair instructions, please refer to the relevant service literature.2 ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Technical features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Engine mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Cylinder block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Warp anchor principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Cylinder head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Pump injectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Crankshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Pistons and conrods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 Gear train . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Ancillary units drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Oil filter module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Oil pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Coolant circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Exhaust gas recirculation cooler . . . . . . . . . . . . . . . . . . . . . . . . . . 24Engine management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26System overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Functional diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Test your knowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323 IntroductionTechnical featuresThe engine is a new development. The development goals were: – compact design to allow longitudinal and transverse mounting – performance gain to 128 kW – low weight, for example by using an aluminium cylinder block – low maintenance requirements, for example by using a maintenance free gear train – soiling resistant ancillary units drive – low number of sealing faces, for example by using a modular design – Crossflow cylinder head with pump injection system305_055Technical features - engine mechanics – Cylinder block with plasma-coated cylinder faces – Single plane gear train with short installation length – Crossflow cylinder head – Crankshaft with integral vibration damper – Upright oil filter module with paper filter element and integrated oil cooler – The 3-phase AC alternator and the air conditioner compressor are driven by elastic drive couplings – Exhaust gas recirculation 4Technical features - engine management – Torque-oriented Bosch EDC 16 engine management system – Pump injection system – Variable geometry turbocharger (electro-pneumatic) Technical dataPower/torque graph2.5 l/96 kW – AXD 2.5 l/128 kW – AXE and BACOutput (kW)Torque (Nm)Output (kW)Speed (rpm)305_017Speed (rpm)305_001Engine codes Type Displacement Bore Stroke Compression ratio Valves per cylinder Firing order Max. output Max. torque Engine management Idling speed Fuel Exhaust gas aftertreatment Exhaust emission standardAXD Transporter 2004AXE Transporter 2004 BAC Touareg - longitudinal mounting 2460 cm3 81 mm 95.5 mm 18.0 : 1 2 1-2-4-5-35-cylinder in-line engine96 kW at 3500 rpm 340 Nm at 2000 rpm Bosch EDC 16 800 rpm128 kW at 3500 rpm 400 Nm at 2000 rpmDiesel (minimum 49 CN) Exhaust gas recirculation, main catalyst EU 3The performance difference between the 96 kW variant and the 128 kW variant is due to software modifications to the engine control unit and differences in the design of the exhaust gas turbocharger. 5Torque (Nm) Engine mechanicsCylinder blockThe cylinder block is made from a high-strength aluminium alloy using the low pressure permanent mould casting method. The cylinder blocks for the Transporter 2004 and the Touareg differ in particular in respect to their starter configuration. – Where the engine is transversely mounted (Transporter 2004), the starter is mounted on the gearbox side. – Where the engine is longitudinally mounted (Touareg), the starter is mounted on the engine side - which is why a starter mounting is cast on here.305_007Plasma-coated cylinder faces The cylinder faces of the 2.5 l R5 TDI engine are plasma-coated. This means that a coating powder is applied to the cylinder wall with a plasma burner. As a result, there is no need for cylinder liners in the aluminium cylinder block. This has the following advantages: – weight reduction compared to press-fitted cylinder liner made from grey cast iron – more compact dimensions due to a smaller distance between the cylinder bores than in the previous production engine with grey cast iron cylinder block – reduced wear through use of the plasmacoated cylinder facePlasma jet with coating powderPlasma burner305_019Cylinder face6 Warp anchor principleTo avoid stresses and to ensure an optimal cylinder shape, the cylinder head and the cylinder block are bolted together by tie bolts. The connection is made by means of sliding sleeves in the cylinder block. The sliding sleeves are placed in the cylinder block and locked against rotation. The sliding sleeve accepts the cylinder head bolt from one side and the tie bolt from the other side.Cylinder head boltCylinder headSliding sleeveCylinder blockTie boltCylinder head bolt305_006305_022The removal and installation procedures, as well as the tightening sequence of the warp anchors and cylinder head bolts, are described in the workshop manual.7 Engine mechanicsCylinder headThe aluminium cylinder head has been developed as a crossflow cylinder head. This means that the intake port and exhaust ports are arranged opposite each other in the cylinder head. This ensures an efficient charge cycle, and therefore improved cylinder charging. All control elements, such as the valves, tappets and rocker levers, have been adopted from other pump injector engines.305_020Exhaust portInlet portElectrical plug connector for pump injectors Cable routing305_021Fuel rail Pump injector Glow plug8 Pump injectorsThe second generation pump injectors used previously in the 1.9 l TDI engine are installed in the 2.5 l R5 TDI engine. They have been adapted in respect to jet position and flow. They have the following notable features: – a low-friction drive – an elevated injection pressure in the part-throttle range – a compact solenoid valveTo keep drive friction to a minimum, the adjusting screw has a rounded end and the pressure pin has a ball socket. The large radii ensure a low surface pressure. In addition, the engine oil collects in the ball socket and thus provides good lubrication between the adjusting screw and the pressure pin.The injection pressure in the part-throttle range has been increased by using a balancer piston with a longer stroke. The pressure in the injector spring chamber rises due to the long stroke of the balancer piston and the flow-restricting action of the inlet bore between the injector spring chamber and the fuel duct. The injector spring is preloaded still further and the injection pressure increases.Adjusting screw Ball socket Pressure pin High pressure chamberBalancer piston Inlet boreFuel return lineFuel supply line Injector springSolenoid valve305_030305_0299 Engine mechanicsSender wheelCrankshaftTo achieve a short installation length, the vibration damper is integrated in the crankshaft.If the crankshaft is removed, the cylinder head must also be dismounted and the cylinder head gasket replaced. Please refer to the workshop manual.Vibration damper305_023Fastening boltVibration damper The vibration damper is mounted to crankshaft by four bolts in lieu of the first counterweight. Vibrations are damped over the full engine load and engine speed range by plastic friction elements.305_025Vibration damperEngine speed sender wheel The gear for driving the gear train is pressed fitted onto the output end of the crankshaft. The sender wheel is machined as part of the crankshaft assembly. This eliminates additional assembly tolerances in the sender wheel and enhances the accuracy of the signal for engine speed measurement.Sender wheel Gear train drive gear305_024The vibration damper can be replaced without having to remove the crankshaft by detaching the first conrod bearing cap. 10 Conrods and pistonsPistons The piston bosses and the small end have a trapezoidal shape in order to minimise the stresses in the pistons and conrods under high combustion pressures. As a result, the combustion forces are distributed over a larger area. To provide good antifrictional properties, the piston bosses have brass bushings. A cooling duct has been cast into the piston in order to cool the piston ring zone. The oil spray nozzles inject oil into this cooling duct as soon as the piston is located at bottom dead center.Cooling ductBrass bushing305_026Conrod The single-piece conrod is made by forging. The connecting rod cap is made by cracking.Trapezoidal small end305_027Piston pin axis offset The piston pin axis is arranged excentrically in order to eliminate noises caused by tilting of the piston at top dead centre. Whenever the connecting rod is inclined, lateral piston forces which alternately press the piston against the cylinder wall are produced. The lateral piston force changes direction at top dead centre. Here the piston is tilted towards the opposed cylinder wall and produces noises. To prevent tilting of the piston and the resulting noises, the piston pin axis is arranged excentrically. By offsetting the piston pin axis, the piston changes sides before it reaches top dead centre and rests against the opposite cylinder wall.Top dead centreCylinder axisPiston pin axis305_02811 Engine mechanicsGear trainDue to the constraints on space, particularly in vehicles with transversely mounted engines, a helical gear train is used. The gear train transmits the high drive forces in a space-saving manner. A 15° helical toothing increases the load-bearing tooth flank width and reduces the gear dimensions to a minimum. The gear train is arranged on the flywheel end. The camshaft and the ancillary units are driven by the crankshaft via the gear train.Clamp T10199 Camshaft gear Intermediate gear (adjustable) Intermediate sprokket Alternator driving gearThe backlash in relation to the camshaft gear is set with the adjustable intermediate gear305_051Coolant pump gearTension gearIntermediate gear Drive gear for vane pump for power steering and air conditioner compressor Intermediate gear Oil pump drive gear305_003Camshaft gearThe gear train is maintenance free. Provision is not made for replacement of gears by after-sales service.12 Ancillary units driveThe ancillary units are driven directly by the gear train. In the alternator and air conditioner compressor, the axis offset tolerances as well as the running irregularities in the longitudinal direction of the drive axis are equalised and damped by an elastic drive coupling. A further advantage is that this coupling not as prone to soiling. This is particularly important for offroad driving and in dusty countries.When removing the alternator, do not take apart the bracket and the alternator.Alternator bracketAlternator305_053AlternatorFreewheelElastic drive coupling Alternator drive gearTension gear (two-piece)Drive gear of vane pump for power steering, air conditioner compressor Vane pump for power steering305_002Air conditioner compressorFreewheel Elastic drive coupling13 Engine mechanicsElastic drive coupling The elastic drive coupling comprises two geared metal hubs which are mechanically connected via a coupling belt.305_014HubCoupling beltHubTension gear The task of the tension gear is to reduce the backlash of the gears which drive the ancillary units. The tension gear is a two-part construction. Both parts are connected by a torsion spring located between the two parts of the gear. Preloading the torsion springs causes the parts of the gear to counterrotate. The backlash of the tension gear and meshing gears is thereby reduced.Tension gearWasherCirclipBush305_056Torsion spring14 Oil filter moduleThe oil filter module is mounted to the cylinder block by five bolts. It comprises an upright oil filter and an integrated oil cooler. The oil filter element is replaced in the upward direction.Oil coolerOil filter305_032Oil coolerAdvantages of the oil filter module – Sealing face with 5-point threaded connection – Eco-friendly upright oil filter with paper element – Integrated oil coolerOil filter305_03315 Engine mechanicsOil pumpThe Duocentric oil pump is bolted to the base of the cylinder block and driven by the crankshaft via gears.305_044The oil pump is located by two fitted sleeves in the cylinder block. Please refer to the workshop manual.Oil pump drive gearCamshaft gearOil circuit supply line A special feature of the oil circuit is that the warp anchor holes are integrated in the oil supply line. Various bearing points and the gear train are supplied with oil through the warp anchor holes.Warp anchor hole305_04616 Oil circuit return line The oil mainly flows back from the cylinder head in the area of the gear train. A further portion of the oil flows back into the oil sump through return bores on both side walls of the engine.Oil return in the area of gear trainReturn bore305_045Oil sump17 Engine mechanicsCoolant circuitThe figure shows the coolant circuit of the Transporter 2004 with an supplementary coolant heater. Various variants are used depending on specification.305_008Key 1 2 First heat exchanger Coolant thermostat (opens when coolant temperature exceeds 80 °C) 3 4 5 6 7 18 Cylinder head Exhaust gas recirculation cooler Coolant pump Cooler Oil cooler 8 9 Cylinder block Vent pipe10 Expansion tank 11 Heater coolant shut-off valve N27912 Non-return valve 13 Second heat exchanger (for rear passenger compartment) 14 Supplementary coolant heater 15 Recirculation pump Coolant pump The coolant pump is designed as a vane pump and is inserted into the cylinder block on the spur gear side. It is driven via gears of the gear train. The coolant pump can be removed without dismantling the gear train housing.Before removing the coolant pump, the coolant must be drained at the coolant drain plugs. This prevents coolant from flowing into the gear train housing and oil sump and mixing with the engine oil.305_049Coolant pump Gear train housing Coolant drain plugCoolant pump Securing bolt Cover Bolt NutGear305_050Special tools are used for removing the coolant pump: coolant pump spur gear puller T10221 and coolant pump puller T10222.19 Engine mechanicsFuel systemThe overview shows the fuel system of the Transporter 2004.Fuel coolerFuel line for supplementary coolant heater Low pressure fuel supply lineFuel temperature senderFuel filter Fuel tank Electric fuel pumpNon-return valve Fuel supply pressure regulating valve Fuel pumpThe electrical fuel pump in the tank serves as a pre-supply pump, and pumps fuel to the fuel filter. The non-return valve prevents fuel from flowing fuel back from the fuel rail and supply line into the fuel tank when the engine is stopped.The fuel filter protects the injection system against soiling and wear by particles and water. The fuel pump pumps the fuel out of the fuel filter and into the fuel supply line under high pressure.20 Fuel rail High pressure fuel supply line Fuel return pressure limiting valve Fuel return line Pump injector305_037ReturnLow pressure supply lineHigh pressure supply lineThe pressure regulating valve sets the fuel pressure in the fuel supply line to approximately 8.5 bar. The pressure limiting valve limits the fuel pressure in the fuel return line to approximately 1 bar. The pressure conditions in the fuel system are thus balanced. The fuel cooler cools the flowing back fuel in order to protect the fuel tank against excessively hot fuel.The fuel temperature sender measures the fuel temperature for the engine control unit. The pump injectors are solenoid valves that are activated by the engine control unit. They are used to control the commencement of injection and injection quantity.21 Engine mechanicsExhaust systemThe exhaust system comprises an exhaust manifold, a main catalyst, a front silencer and a rear silencer.Exhaust manifold The exhaust manifold is an insulated sheet metal manifold with a gas-tight inner shell. This highly compact design ensures a high rate of heating. Additional heat shielding is not required.Exhaust manifold insulationExhaust manifold inner shellsExhaust manifold insulation305_04722 Overview of the exhaust system The overview shows the components of the exhaust system in the Transporter 2004.Main catalytic converterRear silencerFront silencer305_03123 Engine mechanicsExhaust gas recirculation coolerAn exhaust gas recirculation cooler is used in several variants in order to lower the combustion temperature, and thus reduce nitrogen oxide emissions and soot formation.Exhaust gas recirculation cooler305_054Variants: – An exhaust gas recirculation cooler, which continuously cools the exhaust gas, is used in the Transporter 2004 with automatic transmission and in the Touareg with manual gearbox. – A switchable exhaust gas recirculation cooler, which cools the exhaust gas at a coolant temperature upwards of approximately 50 °C, is used in the Touareg with automatic transmission.24 How the switchable exhaust gas recirculation cooler works A switchable exhaust gas recirculation cooler is used, because continuous cooling of the recirculated exhaust gases results in higher hydrocarbon and carbon monoxide emissions. The exhaust gas is ducted either through the cooler or past the cooler to the exhaust gas recirculation valve.Without exhaust gas cooling The exhaust flap remains closed up to a coolant temperature of approximately 50 °C, and the exhaust gas bypasses the cooler.Exhaust gas recirculation cooler To the exhaust gas turbocharger By the coolant temperature sender G62 Exhaust flap Vacuum unit not operatedTo EGR valve Coolant From exhaust manifold305_057With exhaust gas cooling The exhaust flap is opened by the exhaust gas recirculation cooler change-over valve at a coolant temperature of approximately 50 °C. The recirculated exhaust gas now flows through the cooler. The cooling capacity depends on the coolant temperature and the exhaust gas recirculation rate.Exhaust gas recirculation cooler change-over valve N345Vacuum unit operatedEngine control unit J623305_05825 Engine managementSystem overviewThe Bosch EDC 16 Electronic Diesel Control is used in combination with a torque-oriented engine management system in the 2.5 l R5 TDI engine in the Transporter 2004 and in the Touareg.SensorsEngine speed sender G28 Engine control unit J623 Hall sender G40Accelerator position sender G79 Kick-down switch F8 Idling switch F60 CAN drive train data bus Diagnosis connectionAir mass flow meter G70Coolant temperature sender G62Coolant temperature sender - radiator outlet G83Fuel temperature sender G81Charge air pressure sender G31 Intake air temperature sender G42Brake light switch F Brake pedal switch F47Clutch pedal switch F36Additional input signals26 You will find a detailed description of the engine management system in Self-Study Programme 304 "The EDC 16 Electronic Diesel Control".ActuatorsPump injector valves N240 … N244Fuel pump relay J17 Fuel pump (pre-supply pump) G6 Fuel pump G23 *Exhaust gas recirculation valve N18Charge pressure control solenoid valve N75Coolant pump run-on relay J151 Recirculation pump V55Fuel cooling pump relay J445 * Fuel cooling pump V166 *Intake manifold flap change-over valve N239Exhaust gas recirculation cooler change-over valve N345 **Glow plug relay J52 Glow plugs Q10 … Q14Additional output signals * Used in the Touareg ** Used in the Touareg with automatic transmission305_01127 Engine managementFunctional diagram2.5 l R5 TDI engine with the EDC 16 in the Transporter 2004 and Touareg30 15J317F36 + J151 N239 N75 N345 N18MJ445 V55MJ52 V166AQ10...Q14J623+N240 N241 N242 N243 N244G81G62G83G31 G42G40G28F60/F8G7931Additional signals 1 2 3 4 Drive train CAN data bus Drive train CAN data bus Communications line (diagnostic connection) Road speed signal 5 6 7 8 Alternator terminal DFM Cruise control system switch (ON/OFF) Radiator fan - 1st speed Radiator fan - 2nd speed28 KeyA30 15Battery Brake light switch Kick-down switch Clutch pedal switch Brake pedal switch Idling switch Fuel pump (pre-supply pump) Fuel pump * Engine speed sender Charge air pressure sender Hall sender Intake air temperature sender Coolant temperature sender Air mass meter Accelerator position sender Fuel temperature sender Coolant temperature sender radiator outlet Fuel pump relay Glow plug relay Coolant pump run-on relay Voltage supply relay - Term. 30 Fuel cooling pump relay * Engine control unit Exhaust gas recirculation valve Charge pressure control solenoid valve Intake manifold flap change-over valve Injector solenoid valve, No. 1 cyl. Injector solenoid valve, No. 2 cyl. injector solenoid valve, No. 3 cyl. injector solenoid valve, No. 4 cyl. Injector solenoid valve, No. 5 cyl. Exhaust gas recirculation cooler change-over valve ** Glow plug -1Glow plug -2Glow plug -3Glow plug -4Glow plug -5Recirculation pump Fuel cooling pump *F F8 F36 F47 F60 G6 G23 G28 G31 G40 G42 G62 G70 G79 G81 G83AF47FJ17 G23M MG6J17 J52 J151 J317 J445 J623 N18 N75 N239 N240 N241 N242 N243 N244 N345A1G70234567831Q10 Q11 Q12 Q13 Q14 V55 V166305_012AConnection within the function diagram * ** Used in the Touareg Used in the Touareg with automatic transmission29 ServiceDesignationSpecial toolClamp T10199305_052Engine holder for assembly stand T10220305_042Coolant pump spur gear puller T10221305_039Coolant pump puller T10222305_04130 DesignationSpecial toolClutch centring mandrel T10223Graphic unavailable at time of going to pressEngine holder for engine and gearbox lifter (removal and installation) T10224Graphic unavailable at time of going to pressKey for turning the engine T10225305_043Crankshaft locating tool T10226305_04031 Test your knowledgeWhich of the following answers is correct? One or more, or even all, answers may be correct.1.What were the prescribed development goals for the 2.5 l R5 TDI engine? a) b) c) A low weight, for example by using an aluminium cylinder block. A compact design to allow transverse and longitudinal mounting. Low maintenance requirements, for example by using a maintenance free gear train.2.What are the special features of the crankshaft? a) b) c) The engine speed sender wheel is bolted on. The vibration damper is integrated in the crankshaft. The vibration damper can be replaced without removing the crankshaft.3.Which of the following statements on the gear train is true? a) b) c) The backlash of the camshaft gear is adjustable. The gear train is designed to save weight. High drive forces can be transmitted in a space-saving manner by using gears.32 4.Which of the following statements on the ancillary units is true? a) b) The ancillary units are driven by the gear train. In the alternator and air conditioner compressor, the axle offset tolerances and the running irregularities in the longitudinal direction are equalised and damped by an elastic drive coupling. The alternator and the bracket may only be removed completely, and must not be taken apart.c)5.What are the points which must be observed before removing the coolant pump? a) b) c) The coolant must be drained at the coolant drain plugs before removing the coolant pump. The coolant pump can be removed without dismantling the gear train housing. The gear train housing must be removed before removing the coolant pump.6.Which engine management system is used? a) b) c) The EDC 15 Electronic Diesel Control. The EDC 16 Electronic Diesel Control with torque-oriented engine management. The EDC 16 Electronic Diesel Control without torque-oriented engine management.33 NotesAnswers 1. a, b, c; 2. b, c; 3. a, c; 4. a, b, c; 5. a, b; 6. b34 35 305For internal use only © VOLKSWAGEN AG, Wolfsburg All rights and the right to make technical alterations reserved 000.2811.25.20 Technical status 03/03❀ This paper was manufactured from pulp thatwas bleached without the use of chlorine.