TECHNICAL DOCUMENTATION

SSP 322 The 2,0l FSI engine

PDFEN24 pages1 MB
SSP 322 The 2,0l FSI engine - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingSelf-study programme 322The 2.0l FSI engine with 4-valve technologyDesign and function The 2.0l engine is based on the tried and tested 827/113 series. Thanks to FSI technology (Fuel Stratified Injection), the 2.0l petrol engine has taken on a new dimension. FSI engines are more economic, cleaner and more responsive than multi-point injection engines. They also meet today’s requirements in terms of low consumption, environmental issues and increased driving fun.The Volkswagen 1.4-litre/77kW FSI engine, the pioneer in this new generation of petrol engines, demonstrated these advantages at the end of 2000 when it was used in the Lupo. It was then followed by the 1.6-litre/81kW FSI and 1.4-litre/ 63kW FSI in the Polo. This self-study programme should familiarise you with the new technical features of this engine.S322_015NEWImportant NoteThe self-study programme shows the design and function of new developments. The contents will not be updated.For current testing, adjustment and repair instructions, refer to the relevant service literature.2 ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Engine mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Engine management. . . . . . . . . . . . . . . . . . . . . . . . . . 10Functional diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Test yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 IntroductionDescription of engineUsing the Volkswagen Audi platform, the 2.0-litre FSI engine appeared for the first time in the Audi A4, longitudinally mounted with the engine code AWA. In February 2003, the 2.0l FSI engine with the code AXW, identical with the Volkswagen version, was installed transversely in the Audi A3. The following components have been further developed to meet the high demands for engine performance and economy:●●●An aluminium engine block with cast-iron liners A water-cooled exhaust gas recirculation valve (EGR) An exhaust system with two starter catalytic converters fitted close to the engineExhaust gas recirculation valveS322_051Starter catalytic convertersEngine blockS322_0494 ● ● ● ● ●●An intake manifold with change-over barrel for switching between the torque and power channels A new oil filter module Bosch Motronic MED 9.5.10 Four valves per cylinder, operated via roller rocker fingers with upright hydro-elements Aluminium cylinder head with two overhead camshafts and continuous inlet camshaft timing adjustment Direct fuel injection with demand-regulated high-pressure pumpCamshaftsRoller rocker armValvesS322_073 S322_069 Change-over barrel Intake manifoldOil filter moduleS322_047S322_0715 Engine mechanicsThe 2.0l/110kW FSI engine with 4-valve technologyThe 2.0l/110kW FSI engine was used in the Audi A3 in February 2003. Volkswagen used the engine for the first time in October 2003 in the Touran. It will be available for the Golf from the start of 2004.Technical features● ● ●● ●●● ●Single-piston high-pressure pump Plastic variable intake manifold Intake manifold with continuously adjustable charge direction flaps/ intake manifold flaps Water-cooled exhaust gas recirculation valve Roller rocker finger with hydraulic support element Two overhead camshafts with continuous inlet camshaft adjustment Balancer shaft gear assembly in sump Air-guided combustion methodS322_011Technical dataEngine code Type Displacement [mm³] Bore [mm] Stroke [mm] Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel AXW 4-cylinder in-line engine 1984 82.5 92.8 4Torque and power diagram220 200 180 160 Torque [Nm] 140 120 100 80 60 40 20 1000 3000 5000 Engine speed [rpm] 110 100 90 80 Power [kW] 70 60 50 40 30 20 10 7000S322_01211.5:1 110kW at 6000rpm 200Nm at 3500rpm Bosch Motronic MED 9.5.10 Unleaded 98 RON (Unleaded 95 RON with reduction in performance)Exhaust gas treatmentNOx storage catalytic converter and 2 starter catalytic convertersEmissions standardEU 46 Intake manifold with change-over barrelThe two-stage variable intake manifold helps provide the required power and torque characteristics. The pneumatic switching of the change-over barrels from torque to power position is map-controlled. The load, speed and temperature are the relevant variables for this process.Change-over barrelThe change-over barrel in power position. The engine draws in air via the power channel and the torque channel.Power channelS322_065 Torque channelThe change-over barrel in torque position. The engine draws in air only via the torque channel.S322_0677 Engine mechanicsIntake manifold lower part The lower part of the intake manifold contains four intake manifold flaps that are adjusted by the V157 control motor via a common shaft. The G336 potentiometer integrated in the control motor is used to indicate the flap position to the J220 engine control unit.S322_061The oil filter moduleCrankcase breatherThe new oil filter module was developed as a highly integrated plastic unit. Its components include: An oil pressure shut-off valve A paper filter element to filter the oil An integrated water-cooled oil cooler A damper chamber on the crankcase breather for the liquid-vapour separatordamper chamber Oil outletWater inletOil cooler Water outletOil inletOil pressure shut-off valvePaper filter elementS322_045Oil drainage valve8 The cylinder headThe 2.0l FSI engine with 4-valve technology has an aluminium cylinder head. The valves are operated by two overhead camshafts mounted on bearings in a ladder frame to ensure torsional stiffness. The outlet camshaft is driven by toothed belts. The inlet camshaft is driven via the outlet camshaft by a simplex chain. Each intake channel is divided into an upper and lower half by a separating plate. The plates have been shaped so that they can only be fitted in the correct position.Ladder frameOutlet camshaftInlet camshaftSeparating plateS322_0599 Engine managementSystem overviewG71 Intake manifold pressure sender G42 Intake air temperature sender G299 Intake air temperature sender 2 G28 Engine speed sender G40 Hall sender J338 Throttle valve module G187 Throttle valve drive angle sender 1 G188 Throttle valve drive angle sender 2 Diagnosis connectorJ220 Motronic control unitG79 Accelerator pedal position sender G185 Accelerator pedal position sender 2 F F47 Brake light switch Cruise control system brake pedal switchG247 Fuel pressure sender, high pressure G410 Fuel pressure sender, low pressure G61 G66 Knock sensor Knock sensor 2G62 Coolant temperature sender G83 Radiator outlet coolant temperature sender G336 Intake manifold flap potentiometer G212 Exhaust gas recirculation potentiometer G39 G108 G130 G131 Lambda probe Lambda probe II Lambda probe after catalytic converter Lambda probe II after catalytic converterCommunications lineG235 Exhaust gas temperature sender G295 NOx sender J583 NOx sensor control unit G294 Brake servo pressure sensor G476 Clutch position sender J519 Onboard supply control unit J533 Data bus diagnostic interface10CAN drive J538 Fuel pump control unit G6 Fuel pump N30 N31 N32 N33 N70 N127 N291 N292 Injector, cylinder 1 Injector, cylinder 2 Injector, cylinder 3 Injector, cylinder 4 Ignition coil 1 with output stage Ignition coil 2 with output stage Ignition coil 3 with output stage Ignition coil 4 with output stageJ338 Throttle valve module G186 Throttle valve drive J271 Motronic current supply relayJ527 Steering column electronics control unit J234 Airbag control unit J104 ABS control unitN276 Fuel pressure regulating valveN80 Activated charcoal filter system solenoid valveN316 Intake manifold flap air flow control valveN18 Z19 Z28 Z29 Z30 J285 Control unit with display in dash panel insertExhaust gas recirculation valve Lambda probe heater Lambda probe 2 heater Lambda probe 1 heater after catalytic converter Lambda probe 2 heater after catalytic converterZ44NOx sender heaterN205 Inlet camshaft timing adjustment valveV157 Intake manifold flap motorS322_04211 Engine managementExhaust systemThe front section of the exhaust system is split into dual pipes to increase the torque in the lower rev range. Both exhaust sections are equipped with starter catalytic converters. The starter catalytic converters have been permanently fixed to the two exhaust manifolds. Two broadband probes monitor the mixture composition for the starter catalytic converters. Two step-type Lambda probes come after the starter catalytic converters (planar Lambda probes). These monitor the efficiency of the starter catalytic converters. The two exhaust sections then join together at the NOx storage catalytic converter. In lean mix operation, the storage catalytic converter temporarily stores nitric oxide (NOx). The NOx sensor monitors the degree of saturation and triggers regeneration of the storage catalytic converter.Broadband probeStarter catalytic converterS322_043Step-type Lambda probe Temperature sensorNOx storage catalytic converter NOx sensor12 Operating modesThe air-guided combustion method allows use of homogenous and stratified charge modes. The engine electronics select the best operating mode depending on the load and the position of the accelerator pedal. There are 4 main modes: - Stratified lean with exhaust gas recirculation (EGR) - Homogenous lean without EGR - Homogenous with Lambda = 1 and EGR - Homogenous with Lambda = 1 without EGRHomogenousMean pressure [bar]Homogenous with exhaust gas recirculationHomogenous leanStratified leanEngine speed [rpm]S322_040You will find further information in the self-study programme SSP 253 “The petrol direct injection system with Bosch Motronic MED 7”.13 Engine managementStratified charge mode The fuel injection, the combustion chamber geometry and the flow inside the cylinder need to be fine-tuned to make stratified charge mode possible. The following requirements also need to be met: - The engine should be in the appropriate load and rev range. - There cannot be any exhaust gas-related errors in the system. - The coolant temperature should be above 50 °C. - The temperature of the NOx storage catalytic converter should be between 250 °C and 500 °C. - The intake manifold flap should be closed.S322_021 Separating plateIntake manifold flapThe intake manifold flap closes the lower intake duct according to the engine map. As a result, the increased incoming mass of air has to flow through the upper intake duct and starts a tumbling charge movement in the cylinder.High-pressure injectorS322_023The tumbling air flow is enhanced in the cylinder by the air-flow recess in the piston and the upwards movement of the piston.S322_02514 The fuel is injected during the compression stroke just before the ignition point. The fuel is injected at high pressure (40-110 bar) into the flow of air. The air flow then carries the ignitable mixture to the spark plug.S322_027As the injection angle is quite flat, the fuel mist virtually does not come into contact with the the piston head. This is known as an “air-guided” method.S322_029Upon combustion, there is a layer of insulating air between the ignited mixture and the cylinder wall. This reduces the amount of heat transferred via the engine block and thus improves efficiency.S322_03115 Engine managementHomogenous modeIn homogenous mode, the intake manifold flap is moved to an intermediate position according to the engine map. In the combustion chamber, an optimum air flow for achieving lower fuel consumption and emissions is created.S322_033In homogenous mode, the fuel is injected during the intake stroke and not in the compression phase as with stratified charge mode.S322_03516 As the fuel is injected during the intake stroke, the fuel-air mixture has more time to mix thoroughly before ignition.S322_037Combustion takes place in the whole combustion chamber without an insulating air layer or recirculated exhaust gases.S322_039The advantages of homogenous mode are brought about by direct injection during the intake stroke. The fuel evaporation removes some of the heat from the incoming air. Cooling the interior reduces the knocking tendency and thus increases the engine compression and efficiency.17 Functional diagramJ519Terminal 30 Terminal 15 a S S S G G6 S S SN30N32N33N31G28 J538G61G66G1J220N70N127N291N292G185G79 J338 G187 G188 G186N205N316N80N276J271G410bS322_052F F47 G G1 G6 G28 G39 G40 G42 G61 G62 G66 G71 G79 G83Brake light switch Cruise control system brake pedal switch Fuel gauge sender Fuel gauge Fuel pump Engine speed sender Lambda probe Hall sender Intake air temperature sender Knock sensor Coolant temperature sender Knock sensor 2 Intake manifold pressure sender Accelerator pedal position sender Radiator outlet coolant temperature sender G108 Lambda probe IIG130 G131 G185 G186 G187 G188 G212 G235 G247Lambda probe after catalytic converter Lambda probe II after catalytic converter Accelerator pedal position sender 2 Throttle valve drive Throttle valve drive angle sender 1 Throttle valve drive angle sender 2 Exhaust gas recirculation potentiometer Exhaust gas temperature sender Fuel pressure sender, high pressureColour code/legend= input signal = output signal = positive = earth = CAN data bus18 J519 J533 Terminal 30 Terminal 15 a S S Z44 G295 S SG39Z19Z28 G130G108Z29Z30 G131J583F47FG476J220bG62N18G212G247G42 G71G40G336V157G235G83G294S322_054G294 G295 G299 G336 G410 G476 J271 J338 J519 J533 J538 J583 N18 N30 N31 N32 N33Brake servo pressure sensor NOx sender Intake air temperature sender 2 Intake manifold flap potentiometer Fuel pressure sender, low pressure Clutch position sender Motronic current supply relay Throttle valve module Onboard supply control unit Data bus diagnostic interface Fuel pump control unit NOx sensor control unit Exhaust gas recirculation valve Injector, cylinder 1 Injector, cylinder 2 Injector, cylinder 3 Injector, cylinder 4N70 N80 N127 N205 N291 N292 N276 N316 V157 Z19 Z28 Z29 Z30 Z44Ignition coil 1 with output stage Activated charcoal filter system solenoid valve Ignition coil 2 with output stage Inlet camshaft timing adjustment valve Ignition coil 3 with output stage Ignition coil 4 with output stage Fuel pressure regulating valve Intake manifold flap air flow control valve Intake manifold flap motor Lambda probe heater Lambda probe 2 heater Lambda probe 1 heater after catalytic converter Lambda probe 2 heater after catalytic converter NOx sender heater19 ServiceNew special toolsDesignation T10133 FSI special tool case Tool Application Familiar special tools for repairing FSI engines. Also for use with 2.0l FSI engines.S322_063 T40057 Oil drainage adapter For draining the engine oil from the oil filter housingS322_053T40001 Puller T40001/6 Claw attachments for puller T40001/7 Claw attachments for puller S322_055For removing the camshaft wheel20 Notes21 Test yourself1. The engine electronics select the best operating mode depending on the load and the position of the accelerator pedal. Which 4 main modes are used by the 2.0l FSI engine? a) b) c) d)2.What is meant by the “air-led” method used in stratified charge mode? a) The fuel is injected in the direction of the piston head. The fuel mist is then transported to the spark plug together with the tumble-shaped air flow. b) The fuel is injected into the tumble-shaped air flow at a flat angle and transported to the spark plug. c) The fuel directly injected during the intake stroke evaporates in the cylinder and draws part of heat from the incoming air mass.3.Where is the NOx sensor located in the exhaust system? a) In front of the NOx storage catalytic converter. b) In front of the step-type Lambda probes. c) After the NOx storage catalytic converter. d) In front of the starter catalytic converters.22 23 Answers 1.) a) b) c) d) 2.) b 3.) c Stratified injection with exhaust gas recirculation (EGR) Homogenous lean without EGR Homogenous with Lambda = 1 and EGR Homogenous with Lambda = 1 without EGR 322© VOLKSWAGEN AG, Wolfsburg, VK-36 Service Training All rights and rights to make technical alterations reserved 000.2811.43.20 Technical status 10/03❀ This paper was manufactured from pulp thatwas bleached without the use of chlorine.