TECHNICAL DOCUMENTATION

SSP 347 Tyre Pressure Monitoring Systems

PDFEN56 pages2 MB
SSP 347 Tyre Pressure Monitoring Systems - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingSelf-study Programme 347Tyre Pressure Monitoring SystemsDesign and Function Tyre pressure monitoring systems monitor the inflation pressure of the tyres. They can warn you about dangerous changes in pressure and send a signal when the actual tyre pressure deviates from the specified tyre pressure. The tyre pressure affects road safety, comfort, the service life of the tyres and fuel consumption.In Volkswagen vehicles, the tyre pressure is monitored using three different systems: - the tyre pressure monitor display (TPMD), which is purely a software solution, - the tyre pressure monitor (TPM) with wheel position recognition in the Touareg and Phaeton and - the TPM without position recognition in the Passat.S347_050NEWImportant NoteThe self-study programme shows the design and function of new developments. The contents will not be updated.For current testing, adjustment and repair instructions, refer to the relevant service literature.2 ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4TPM tyre pressure monitor display✱ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8TPM with position recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22TPM without position recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Test Yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52✱Not for the North America region (NAR)3 IntroductionTyre pressureCorrect tyre pressureA tyre with the correct tyre pressure rolls along the road using the full tread surface. The tread wears evenly and the full amount of grip is provided. This has the following advantages: high tyre mileage, minimum braking distance, optimum cornering stability and best ride comfort.S347_019S347_020Tyre pressure too highWhen the tyre pressure is too high, only the centre of the tread provides optimum power transmission. This has the following disadvantages:S347_021- uneven tread wear, - reduced tyre life and - reduced ride comfort.S347_022Tyre pressure too lowIf the tyre pressure is too low, the tyre will be slightly concave in the middle so that only the outside surface transfers the power properly to the road surface. This has the following disadvantages: - considerable heating up of tyres and thus a risk of damage to the tyre structure, - longer braking distances and - shortened tyre life.S347_024S347_0234 What does the tyre pressure depend on?The volume remains approximately the same in a tyre. Therefore temperature changes inside the tyre affect the tyre pressure directly. The tyre pressure is increased or decreased by approx. 0.1bar for every 10 degrees change in the temperature. The inside temperature of the tyre is subject to various influences: - the outside temperature or sunlight, - the heat emitted from the brake discs and - the flexing of the tyres.30°C 20°C 10°C2.4bar2.5bar2.6barS347_044S347_045S347_046Dangerous low tyre pressureLow tyre pressure often causes punctures. If the pressure in a tyre is too low over a long period, the temperature inside the tyre increases due to the flexing of the tyres. This causes damage to the tyre structure. If the tyre structure becomes too badly damaged, the tyre will be destroyed.5 IntroductionOverview of tyre pressure monitoring systemsThe following applies for all tyre pressure monitoring systems: The tyre pressures are monitored constantly and compared with reference values. All systems issue tyre pressure warnings.Tyre pressure monitor display✱ The tyre pressure monitor display (TPMD) is a software module in the ABS control unit. It evaluates ABS data and recognises tyre faults on individual wheels. The driver himself inflates the correct specified tyre pressures and the system stores them after he presses a button as part of a learning process.ABS data Tyre pressure Control unit Warning lampS347_025 Wireless transmission Wheel electronicsAerialTyre pressure monitor with position recognition In the Touareg and Phaeton, the tyre pressure monitoring systems with position recognition comprise wheel electronics, aerials for contact-free transfer of the sensor data from the wheel electronics and a control unit. The driver inflates the tyres to the correct pressures and stores them in the system.S347_026Tyre pressure monitor without position recognition The tyre pressure monitor software without position recognition in the Passat is integrated in the convenience system central control unit. The central locking and anti-theft alarm system aerial is used to receive the data from the wheel electronics. In this system, the specified tyre pressure is preset in the factory.S347_051✱Not for the North America region (NAR)6 Procedure following tyre pressure warningIf a warning is issued from the tyre pressure monitor systems (except for “soft warning” with TPM systems), you should reduce your speed immediately. Avoid sharp steering and braking. You should stop at the next opportunity and check the tyres and their pressures. The driver is responsible for ensuring that the tyre pressure is correct. Therefore he should check the tyre pressures on a regular basis.Main features of systems in comparisonTPM✱TPM with position recognitionTPM without position recognition Tyre pressure monitor control unit module J502 in convenience system central control unit J393SoftwareModule in ABS control unit J104Separate tyre pressure monitor control unit J502Wheel electronicsNot installedOne per wheelOne per wheelAerialsNot installedOne per wheel housingNot installed, the wheel electronics signals are received by the central locking and antitheft alarm system aerialSpecified tyre pressuresNeed to be inflated by driver and stored in the system by pressing the buttonNeed to be inflated by driver and stored in the system by pressing the buttonPreset in factoryOperatingUsing a button. Icon:Via the “Convenience Setup” (Touareg) or the infotainment system (Phaeton). S347_052Using a button. Icon:✱S347_053 The learn process needs to be started after the tyres have been inflated to the correct pressure. New wheel electronics are learnt, the specified tyre pressures remain the same.Learn processThe system learns the specified tyre pressure in a calibration process.✱Not for the North America region (NAR)7 TPM tyre pressure monitor display✱DesignThe tyre pressure monitor display is a software module without its own diagnosis address in the ABS control unit J104. It recognises slow pressure loss in a tyre and is available as an optional extra for the Golf, the Passat and the Polo.G45 Front right speed sensor E492 Tyre pressure monitor display buttonG44 Rear right speed sensorJ104 ABS control unitJ285 Control unit with display in dash panel insert J533 Data bus diagnostic interface J519 Onboard supply control unit G47 Front left speed sensorS347_034 G46 Rear left speed sensorIf one of these vehicles is equipped with self-supporting tyres, the tyre pressure monitor display will always be installed. When self-supporting tyres are equipped, the driver will hardly notice low tyre pressure therefore a tyre pressure monitoring system is always required. Warnings are indicated in the dash panel insert by a tyre pressure warning lamp. A button in the centre console is used to configure the tyre pressure monitor display for the new tyre conditions after the tyre pressure has been adjusted, tyres have been changed or work has been carried out on the chassis (calibration of system).Customer services must inform customers that the driver is responsible for setting the correct tyre pressure. The tyre pressure monitor display is an information system that issues a warning when pressure is lost at one tyre. It does not, however, relieve the driver of the responsibility to check the tyre pressure himself on a regular basis.✱Not for the North America region (NAR)8 FunctionVarious data from the anti-lock brake system is used to determine the rolling circumference of a tyre. The rolling circumference is compared with reference data. Pressure loss in the tyre can be detected from slight changes. The reference data is calculated from the current driving data in a system learn process, called calibration. If the TPM detects the signal from the hand brake (Golf) or the electromechanical parking brake (Passat), it will be deactivated automatically for the duration of the signal. Spare wheels, temporary spare wheels and trailers are not monitored with the TPM. The system needs to be calibrated after a wheel is changed.OperationThe calibration is started with the tyre pressure monitor display button, which is built into the centre console in the Golf.S347_039WarningIf a pressure loss is detected, the driver will be warned by the tyre pressure monitor warning lamp in the dash panel insert and a single gong. The lamp will be illuminated until the system is calibrated again. Until the system is calibrated, the gong will sound each time the car is started.S347_0479 TPMD tyre pressure monitor displayUse of button●●Hold down the button for 2 seconds: - The tyre pressure monitor warning lamp is illuminated for 2 seconds, - a gong sounds, - the system calibration starts, - you can let go of the button. Hold down the button for 30 seconds or button sends a signal for 30 seconds: - The software recognises that a button is jammed or there is short-circuit, - The tyre pressure monitor warning lamp starts to illuminate and - An entry is made in the fault memory. - If the button contact is opened again, the lamp extinguishes when the ignition is turned on again and the fault memory is set to “sporadic”.Tyre pressure monitor warning lamp statesState Tyre pressure warning S347_005 Optical signals Acoustic signals Single gong each time ignition is turned on... until the system is re-calibrated after the tyre pressure has been adjusted.Ignition on with existing tyre pressure warningSingle gong each time ignition is turned on... until the system is re-calibrated after the tyre pressure has been adjusted.System errorNone... until the system error is rectified. If you press the button to re-calibrate the system, it will not be accepted.10 CalibrationAs the tyre characteristics change, a calibration procedure needs to be carried out to determine new reference data whenever the inflation pressure has been changed, after any repair work on the chassis and after each time the tyres are changed.Starting calibration2 secondsTo start calibration, you need to hold down the tyre pressure monitor display button for 2 seconds. The warning lamp in the dash panel insert illuminates for approx. 2 seconds. A gong also sounds. The system calibrates itself in normal driving operation to the tyre pressures inflated by the driver and the tyres fitted. As the calibration progresses, it gradually transfers data to the tyre pressure monitoring system. After just a few minutes, rough monitoring is possible with the speeds and driving situations that the system has already learnt.Normal driving operationCalibration progress in all driving situationsS347_06411 TPMD tyre pressure monitor displayFunction requirementsDelay of a tyre pressure warningThe rolling circumference of a tyre, which is determined and used by the tyre pressure monitor display, depends on several factors. In addition to the tyre pressure, the following should be named: the drive and brake slip, the wheel position when cornering, the loading of the vehicle and the road conditions (the road surface, snow, ice, wet).As the rolling circumference is determined for the tyre monitoring display from various operating data, it cannot clearly be based on the tyre pressure in certain situations. That means: Data evaluation is stopped if the driver has a sporty driving style, the road surface is uneven and loose, when the driver brakes and when travelling uphill or downhill. It is not possible to detect a loss in pressure in these situations. Any tyre pressure warning is delayed until the driving conditions return to normal.False warningsFalse warnings can occur when several unfavourable situations occur in succession. A false warning can be triggered if several of the following situations occur: different road surface conditions (e.g. one side of the road is icy and the other not), uneven loading of the vehicle, uneven tyres on one axle (e.g. one very worn and one new tyre) and uneven heating of the wheels on one side of the car due to direct sunlight.12 System overviewJ285 Control unit with display in dash panel insert K220 Tyre pressure monitor warning lampFBrake light switchH3 J 104 ABS control unit G44 - G47 Speed sensorBuzzer and gongL76Button illumination bulbE492 Tyre pressure monitor display buttonFurther information on the driving situation (e.g. engine data) J533 Data bus diagnostic interfaceJ 519 Onboard supply control unit (not in Polo) F9 Handbrake warning switch (only in Golf)J540 Control unit for electromechanical parking brake (only in Passat)S347_007 E538 Electromechanical parking brake button (only in Passat)13 TPMD tyre pressure monitor displayFunctional diagramGolf functional diagramF G44 G45 G46 G47J104J533J285J519K220H3E492L76F9S347_032E492 F F9 G44 G45 G46 G47 H3 K220Tyre pressure monitor display button Brake light switch Handbrake warning switch Rear right speed sensor Front right speed sensor Rear left speed sensor Front left speed sensor Buzzer and gong Tyre pressure monitor warning lamp Button illumination bulbJ104 J285 J519 J533ABS control unit Control unit with display in dash panel insert Onboard supply control unit Data bus diagnostic interfaceL76Colour code/legend Input signal Output signal Positive Earth CAN data bus14 Passat functional diagramG44 G45 G46 G47J104J533 J540J519 E538 J285E492L76FK220H3S347_072E492 E538 F G44 G45 G46 G47 H3 K220Tyre pressure monitor display button Electromechanical parking brake button Brake light switch Rear right speed sensor Front right speed sensor Rear left speed sensor Front left speed sensor Buzzer and gong Tyre pressure monitor warning lamp Button illumination bulbJ104 J285 J519 J533 J540ABS control unit Control unit with display in dash panel insert Onboard supply control unit Data bus diagnostic interface Electromechanical parking brake control unitL7615 TPMD tyre pressure monitor displayPolo functional diagramF G44 G45 G46 G47J104From E1 J285E20K220H3L76E492S347_073E1 E20 E492 F G44 G45 G46 G47 H3 K220Light switch Switches and instruments illumination regulator Tyre pressure monitor display button Brake light switch Rear right speed sensor Front right speed sensor Rear left speed sensor Front left speed sensor Buzzer and gong Tyre pressure monitor warning lamp Button illumination bulb ABS control unit Control unit with display in dash panel insert Colour code/legend Input signal Output signal Positive Earth CAN data busL76 J104 J28516 ServiceDiagnosisThe fault memory for the tyre pressure monitor display is in the ABS control unit J104. There are two (Golf) or four (Passat and Polo) different fault tyres: “Tyre pressure warning” entry (only Passat and Polo) “Tyre pressure warning faulty” entry “Tyre pressure warning: button faulty” entry “Tyre pressure warning limited function” entry (only Passat and Polo)Procedure for “tyre pressure warning”If a tyre pressure warning is entered in the fault memory and the tyre pressure monitor warning lamp, the tyres should be examined for damage and the tyre pressures checked. Once the fault has been rectified, the calibration needs to be started so that the tyre pressure monitor warning lamp extinguishes. “Sporadic” may be added at the end of the tyre pressure warning. In this case, a tyre pressure monitor warning was entered, but the warning was removed after the system was calibrated again. The tyre pressure monitor warning lamp does not illuminate. The tyre pressures and the tyres should be checked, however, before this fault memory entry is deleted.Tyre pressure warningOKS347_05917 TPMD tyre pressure monitor displayProcedure for “tyre pressure warning faulty”This fault message will be rare in practice. If it occurs in the fault memory, a system reset should be carried out. ELSA provides detailed information on the procedure.Procedure for “tyre pressure warning button faulty”If “Tyre pressure warning: Button faulty” is entered in the fault memory, the tyre pressure monitor display button has sent a signal for longer than 30 seconds. The tyre pressure monitor warning lamp illuminates. “Sporadic” may be entered after the “Tyre pressure warning: Button faulty” if the button contact is no longer closed. In both cases, the button should be checked (e.g. to see if it is jammed or there is moisture inside) and the system should be checked for a short-circuit before the fault memory is cleared.Tyre pressure warning button faultyOKS347_060Please press the button to calibrate the system again after each time the tyres are changed and after repair work on the chassis. If you do not do this, the system may work with incorrect data. Tell your customers if you make changes to the tyre pressure monitor display (e.g. system calibration).18 Tyre pressure warning limited functionProcedure for “tyre pressure warning limited function”If “tyre pressure warning limited function” is entered in the fault memory, the system is receiving insufficient data from the engine control unit. The tyre pressure monitor warning lamp does not illuminate. The system works with limited accuracy. “Sporadic” may be added after “tyre pressure warning limited function” if the data has been received completely again in the meantime. In both cases, the engine control unit fault memory should be read out and the cause rectified.S347_061Engine control unitPlease use the guided fault finding function and ELSA for diagnosis of the tyre pressure monitor display.19 TPMD tyre pressure monitor displayWorkshop informationReplacing the ABS control unit J104When you change the ABS control unit J104, you should observe the following: - Is the vehicle equipped with the tyre pressure monitor or not? If yes, it needs to be coded actively and set to the brake size of the car for the Golf. After active coding, the tyre pressure monitor will automatically start with system calibration. - The tyre pressures need to be inflated correctly before active coding. - To test, you should press the tyre pressure monitor display button. The tyre pressure monitor warning lamp in the dash panel insert should then illuminate and the system calibration will start again.TPM active codingSet TPM to brake size (Golf only)2 secondsNormal driving operationELSA provides detailed information on the procedure.Calibration progress in all driving situationsS347_06720 Differences between modelsGolf Signal from handbrake switch is evaluated. Passat Information from the electromechanical parking brake is evaluated. Polo Neither handbrake nor parking brake signal is evaluated.No fault memory entry “tyre pressure monitor limited function” and “tyre pressure warning”.“Tyre pressure monitor limited function” and “tyre pressure warning” fault memory implemented.“Tyre pressure monitor limited function” and “tyre pressure warning” fault memory implemented.Manual adaptation to brake size in software module for tyre pressure monitor display.Automatic adaptation to brake size in software module for tyre pressure monitor display.No adaptation to brake size in software module for tyre pressure monitor display.21 TPM with position recognitionDesignThe tyre pressure monitor with position recognition for the wheels is currently used in the Phaeton and Touareg and has the same basic configuration for both vehicles. The diagram below shows the Phaeton.J218 Combi-processor in dash panel insertFunction selection switch in infotainment systemR59-R62 Aerials for tyre pressure monitorShielded HF linesS347_040G222 - G226 Tyre pressure sensors (wheel electronics)J502 Tyre pressure monitor control unitThe tyre pressure monitor with position recognition constantly monitors the tyre pressure while the car is being driven. When the car is stationary, there is also tyre pressure monitoring over a short period. The wheel electronics mounted on the tyres measure the tyre temperature and tyre pressure. This data is sent from the wheel electronics to the aerials in the wheel housings at regular intervals. The aerials are connected to the tyre pressure monitor control unit via shielded HF lines (high-frequency lines). The data is evaluated in the tyre pressure monitor control unit and forwarded to the control unit in the dash panel insert and also the infotainment system in the Phaeton. The correct tyre pressures need to be inflated by the driver and accepted as specified tyre pressures by pressing a button. In the Phaeton, it is operated via the infotainment system and, in the Touareg, via the “Convenience Setup” in the dash panel insert. Messages and warnings are indicated by a lamp in the dash panel insert and text appears in the dash panel insert display.22 Wheel electronics set-upThe wheel electronics are screwed to the metal valves and can be used again when the wheels or tyres are changed. The following components are integrated in the wheel electronics: are transmission aerial, a pressure and temperature sensor, the measuring and control electronics and a battery.Tyre pressure sensor Transmission aerial G222-G226Pressure and temperature sensor Measuring and control electronics Metal valve Battery S347_031 S347_030Transmission intervals●●Transmission interval of wheel electronics in normal operation: every 54 seconds. Transmission interval of wheel electronics in fast transmission mode (if pressure loss 0.2bar/min): every 850 milliseconds.To compensate the thicker walls of the Touareg tyres, the transmission power of the tyre pressure sensors has been increased. The Touareg sensors can be recognised by the eight white stars on the top. Transmission power: - Phaeton: 10 µW–30 µW - Touareg: approx. 100 µW23 TPM with position recognitionFunctionWhat is detected?The tyre pressure monitor with position recognition in the Phaeton and Touareg has the following functions: - Tyre pressure display with wheel position recognition (Phaeton: constantly in infotainment system; Touareg: in “Convenience Setup" when stationary) - Recognition of slow loss of pressure: The driver is informed in good time to check the tyre pressure and correct it if necessary. - Recognition of sudden loss of pressure: The driver is warned immediately as he drives. - Detection of pressure loss when vehicle is stationary: The driver is warned immediately after he turns on the ignition.Position detection is possible using the four aerials. Changes to the pressure can be assigned immediately to the respective tyre. In the Phaeton, a full-size spare wheel is equipped with wheel electronics. These signals are received by the aerials and assigned to the spare wheel. When a wheel is changed, the new wheel electronics have to be learnt. This happens after a button is pressed while you drive. The vehicle needs to be travelling at least 25km/h. The spare wheel and trailer are not monitored.The externally mounted spare wheel on the Touareg may not be equipped with wheel electronics to avoid system interference.24 OperationMarkerMessages and warnings from the tyre pressure monitor with position recognition are indicated by two icons (marker and warning symbol) in the centre display of the dash panel insert. In the Touareg, you will find the TPM functions in the “Tyre Pressure Monitor” menu in the “Convenience Setup” main menu in the dash panel insert. The “Convenience Setup” menu can only be called up when the car is stationary. You navigate through the “Tyre Pressure Monitor” menu item in the Touareg either using the steering column switch or the multifunction steering wheel. In the Phaeton, the tyre pressure monitor is operated using the infotainment system in the “Vehicle” menu.S347_029Warning symbolTyre pressure monitor functionsThe following functions can be called up in the “Convenience Setup” (Touareg) or in the Infotainment system (Phaeton): - ON/OFF: Switches the whole tyre pressure monitoring system on and off. - MON. PRESSURES: The pressures that the driver inflated and stored for the monitoring are displayed. (This function is called “Specified pressures” in the Phaeton.) - PRESSURE INFO: The specified pressures of the tyres at the current tyre temperature are displayed here. The driver can therefore also correct the tyre pressure when the tyres have warmed up when warnings are issued (add air). - SAVE: After changing the tyre pressures (e.g. to correct to “fully loaded”) or when new wheel electronics are installed (e.g. in winter tyres), the tyre pressures set by the driver are accepted by the system as specified pressures to be monitored. This starts the vehicle learn process. (This function is called “Accept new specified pressures” in the Phaeton.) - The Phaeton also has the “spare wheel monitoring” function.25 TPM with position recognitionMessages in dash panel insertIf the system is fully functioning and there are no warning messages, a TPM symbol will not appear in the dash panel insert.At a pressure reduction from 0.3 to 0.4bar there is a soft warning. The adjacent display appears with a warning tone for 5 seconds and then also each time you turn on the ignition. The large symbol is hidden after 5 seconds. The marker remains until the tyres are inflated to the correct pressure.Check tyre pressures S347_043There is a hard warning at a pressure reduction greater than 0.4bar or a fast pressure loss of at least 0.2bar per minute. This indication cannot be acknowledged, i.e. it will not disappear when you press a button.Flat tyre S347_042If there was a puncture during an ignition procedure, the adjacent message will be displayed when the ignition is turned on. Within the next 5–7 minutes, the system will check whether the tyre pressures are correct again. If this is the case, the icons will disappear.DEFECTIVE WHEEL ON S347_070When the system is learning, the adjacent display will appear as an indication that the TPM is not working correctly. The large icon will disappear after 5 seconds, the marker remains displayed until the learning process is completed. The “system fault” and “system off” states are indicated by the same icons.System is learning S347_04126 Infotainment system in the PhaetonIn the Phaeton, the tyre pressure monitor is operated with the “Vehicle” function button in the infotainment system.S347_028System learn processAfter any changes to the tyres on a car, the system learning process needs to be started in the tyre pressure monitor menu using the “SAVE” menu item (Touareg) or “Accept new specified pressures” (Phaeton). Changes to the tyres can include: - Correction of the tyre pressure from partial loading to full loading, - installation of other wheel electronics on one or all wheels (e.g. winter wheels or changing a damaged wheel). The learning process only starts when you drive faster than 5km/h. It takes approx. 7–10 minutes if the data is received without interference. When the learning process is completed, the marker in the dash panel insert disappears. The learning process involves: - Detection of the actual tyre pressures. - Acceptance of the actual tyre pressures as specified tyre pressures. - Check whether the previous wheel electronics are still installed in the vehicle. If they have been changed, they will be learnt again. - Check whether the position of the wheel electronics has changed. If this is the case, the new positions will be stored.When wheels without wheel electronics are fitted, the system should be switched off.You will find more information on tyre pressure monitoring with position recognition in self-study programme 277 “The Phaeton – Chassis” and self-study programme 302 “The Touareg – Chassis and four-wheel drive concept”. Information on operation of the tyre pressure monitoring system in the Phaeton can also be found in the multimedia training programme “The Phaeton – Infotainment Simulation”.27 TPM with position recognitionFunction requirementsThe following conditions need to be met so that the tyre pressure monitor works properly: 1. The driver has to inflate the tyres to the correct pressure also observing the different tyre pressures for full and partial loading. 2. External radio interference sources may not interfere with the wireless connection between wheel electronics and aerials. 3. The batteries in the wheel electronics should not have run flat. The life of the batteries is approx. 10 years.Phaeton system overviewJ502 Tyre pressure monitor control unitG222 - G226 Tyre pressure sensorsR59-R62Aerials for tyre pressure monitorJ218 Combi-processor in dash panel insertS347_009 J523 Front information display and operating unit control unit28 Touareg system overviewJ502 Tyre pressure monitor control unitG222 - G225 Tyre pressure sensorsR59-R62Aerials for tyre pressure monitorJ218 Combi-processor in dash panel insertS347_010 J453 Multifunction steering wheel control unit or steering column switchElectrical componentsTyre pressure sensors G222-G226Sent information The tyre pressure sensors G222-G226 transfer the following data via the individual integrated sensors: Tyre pressure and tyre temperature, the specific identification numbers (ID), the state of the integrated battery and the status, synchronisation and control information required for safe data transfer. Signal use The signals from the tyre pressure sensors contain the current measured tyre pressure with which the tyre pressure monitor control unit can recognise critical tyre situations and can inform the driver. Sensor failure When a sensor fails, a fault message is displayed in the dash panel insert.29 TPM with position recognitionAerials for tyre pressure monitor R59-R62Function Each aerial receives the radio signals from all tyre pressure sensors within its range. The power of the received radio signal is decisive for recognition of the nearest wheel electronics.S347_016Signal use The aerials forward the received signals for further processing to the tyre pressure monitor control unit. They are connected to the control unit via highfrequency aerial cables and assigned in the control unit according to their location.Effects upon failure When one aerial fails, the system still works because the other three aerials receive the signals from the wheel electronics and can assign the positions accordingly. If two aerials fail at the same time, the system will not be able to perform a learn process and wheel position recognition will no longer be possible. Therefore, when the learn process is started, the “system fault” message will be issued.30 Functional diagramG222G223G224G225G226*R59R60R61R62Terminal 15SJ502S347_015Terminal 31J218J523*J453**G222 G223 G224 G225 G226 J218 J453 J502 J523Front left tyre pressure sensor Front right tyre pressure sensor Rear left tyre pressure sensor Rear right tyre pressure sensor Spare wheel tyre pressure sensor Combi-processor in dash panel insert Multifunction steering wheel control unit Tyre pressure monitor control unit Front information display and operating unit control unitR59 R60 R61 R62Front left tyre pressure monitor aerial Front right tyre pressure monitor aerial Rear left tyre pressure monitor aerial Rear right tyre pressure monitoring aerialSFuse* **only in Phaeton only in TouaregColour code/legend Input signal Positive Earth CAN data bus Wireless connection31 TPM with position recognitionServiceDiagnosisThe tyre pressure monitor control unit J502 can be read with the VAS 5051/VAS 5052 for diagnosis of the tyre pressure monitor with position recognition in the Phaeton and Touareg.Detecting faulty wheel electronicsIf the wheel electronics have been learnt, the faulty wheel electronics unit is indicated with position. If, however, one wheel electronics unit is faulty in a new set, the system will not be able to carry out a learn process. Therefore the position of the faulty wheel electronics unit is not displayed. In this case, the faulty wheel electronics have to be determined as follows: 1. Call up the corresponding diagnosis address (address 65, read data block MWB 16). The identification number (ID) of the wheel electronics that last sent a data telegram is entered here. 2. Change pressure on a tyre by at least 0.2 bar per minute (e.g. release pressure). If the wheel electronics on the wheel where you changed the pressure are not faulty, it will be now be entered in data block 16 with status 02 (wheel electronics have signals due to a fast pressure change). If this is the case, the wheel electronics are not faulty. The procedure should then be repeated with the next wheel.Address 65, Data block 16Pressure change in one tyreNo change in data blockS347_065ELSA provides detailed information on the procedure.32 Move vehicle3. If the data block entry is not changed despite the change to the pressure of one tyre, you need to rule out that the signal reception from the respective wheel electronics is working properly. Do this by changing the position of the valve slightly by moving the vehicle. 4. If the entry for the last wheel electronics signal received still has not changed, the corresponding wheel electronics are faulty.No change in data block: Wheel electronics faultyS347_071Replacing the tyre pressure monitor control unit J502The following work needs to be carried out after the tyre pressure monitor control unit J502 has been replaced: - Active coding of system with the VAS 5051/VAS 5052, - inflating tyres to pressure specified on the tyre pressure label inside the fuel filler flap, - acceptance of new specified pressures: “Vehicle” menu in the Infotainment system in the Phaeton, in the “Convenience Setup” in the Touareg. - Starting the system learn process with a learning drive.Differences between modelsPhaeton Operation via “Vehicle” in infotainment system. Touareg Operating via multifunction steering wheel or steering column switch in the “Convenience Setup” menu.Monitoring the spare wheel if present.Monitoring of external spare wheel not possible.33 TPM without position recognitionDesignWheel electronics are mounted on each wheel in the tyre pressure monitor system without position recognition used in the Passat. The wheel electronics send data telegrams at regular intervals, which are received by the central locking and antitheft alarm system aerial and forwarded to the tyre pressure monitor control unit J502. The control unit has its own diagnosis address in the convenience system central control unit.Central locking and anti-theft alarm system aerialTyre pressure sensor (wheel electronics)Tyre pressure monitor button E226✱Tyre pressure sensors (wheel electronics)Tyre pressure monitor control unit J502, integrated in convenience system central control unit J393S347_038 Control unit with display in dash panel insert J285 Tyre pressure sensor (wheel electronics) Tyre pressure sensor (wheel electronics)The specified tyre pressures (monitoring pressures) are stored in the factory. The pressures are valid for a set of wheels with tyres that are approved by the authorities and Volkswagen as specified on the fuel filler flap. The specified tyre pressures for partial and full loading of the vehicle are preset and may not be changed. The driver can use the button in the centre console to switch between partial and full loading, to check the status and switch the tyre pressure monitor on and off.✱ Messages and warnings are indicated by the lamp in the dash panel insert and text appears in the dash panel insert display.It is planned to also use the TPM without position recognition in the Golf in the future.✱Not for the North America region (NAR)34 Wheel electronics set-upThe wheel electronics of the TPM without position recognition have a different configuration to the TPM with position recognition in the Touareg and Phaeton. They have the following components: a pressure sensor, a temperature sensor, an acceleration sensor, a battery, measuring and control electronics and a transmission aerial.Identification numberAerial connection to electronicsFrequency rangePressure sensor openingThe valve is used as an aerial so that the signals are not shielded by the tyre materials. The valve is connected to the measuring and control electronics for the wheel electronics.S347_018 Valve acting as aerialTechnical Data●Transmission intervals●●● ●Power supplied from high-temperature resistant lithium-ion batteries (life approx. 10 years) Transmission frequencies 315MHz and 434.42MHz (depending on country, in Germany 434.42MHz) Weight approx. 45g with valve Operating temperature -40°C to 120°CTransmission interval of wheel electronics when driving above 25km/h: At first, 30 data telegrams with a transmission interval of 15 seconds, the subsequent data telegrams with a transmission interval of 60 seconds. Transmission interval of wheel electronics in fast transmission mode (if pressure loss 0.2bar/min): Every 15 seconds.●35 TPM without position recognitionFunctionNot for the North America region (NAR)The tyre pressure monitor without position recognition in vehicles for the North America region (NAR) is installed without the tyre pressure monitor button. The system without the button works in exactly the same way as the system with button except for the button functions and the lack of “soft warning”.Wheel electronicsThe wheel electronics installed in the wheel constantly measure the internal tyre temperature, the inflation pressure and the centrifugal acceleration of the respective tyre. The data telegrams are sent depending on the state of the vehicle. When the car is stationary or travelling below 25km/ h, no data telegrams are sent unless the wheel electronics recognise a fast change in pressure of more than 0.2bar per minute. If the wheel electronics recognise centrifugal acceleration above 5g (corresponding with a vehicle speed above approx. 25km/h), 30 data telegrams will be sent with a transmission interval of 15 seconds. After that, i.e. in normal driving, the wheel electronics send one data telegram per minute. After any fast pressure change of more than 0.2bar per minute, the wheel electronics send a data telegram every 15 seconds.Normal driving operation: One data telegram per minute When stationary: No data telegrams without fast pressure changeS347_055Above approx. 25km/h: 30 data telegrams with a transmission interval of 15sec.S347_068S347_05736 What is detected?The tyre pressure monitor without position recognition in the Passat recognises three critical tyre conditions, in which warnings for the driver are indicated by the lamps and the display in the dash panel insert:- the actual tyre pressures deviate slightly under the specified tyre pressures in the range 0.3 to 0.4bar (soft warning without gong)✱,S347_035- large, but not sudden deviation of the actual tyre pressures from the specified tyre pressures above 0.4bar (hard warning with gong),S347_036- sudden great deviation of actual tyre pressures from the specified tyre pressures in the range of more than 0.2bar per minute (hard warning with warning tone).S347_037If one component from the tyre pressure monitor without position recognition in the Passat fails or radio interference is detected, the tyre pressure warning lamp in the dash panel insert will inform the driver.✱Not for the North America region (NAR)37 TPM without position recognitionChanging wheelsIf you change wheels, the wheel electronics will send data as soon as the speed of the new wheels is more than 25km/h. The identification numbers of the new wheel electronics are recognised and read automatically. The acceleration data is also checked with the vehicle speed. This procedure takes approx. 7 min.The tyre pressure monitor control unit needs to switch to learn stand-by before it can automatically start a learn process for the wheel electronics. The vehicle needs to be stationary for 20 minutes for this. After a tyre puncture has been recognised, it will take 5 minutes. If the stationary time is not observed and the control unit is thus not in learn stand-by, the system will recognise radio interference and will only start learning the wheel electronics after a stationary period of 20 minutes.20 minutes or 5 minutes after a tyre pressure warningAfter approx. 7 minutes driving above 25km/h, the wheel electronics will be learnt.Wheel electronics are learntS347_06338 Spare wheelWheel electronics can be fitted on a full-size spare wheel. As long as the spare wheel is not fitted, the wheel electronics will not transmit any signals. However, if the wheel electronics recognise centrifugal acceleration above 5g (approx. 25km/h vehicle speed), it will send data telegrams that are received by the tyre pressure monitor control unit. The control unit then stores the data and the identification number of the new wheel electronics integrated in the system. Temporary spare wheels and trailers are not monitored by the tyre pressure monitor without position recognition in the Passat.The factory preset specified tyre pressures (for wheel set 1) cannot be changed. If you use tyres that require other tyre pressures than those specified on the label inside the tank filler flap, it is possible to enter specified tyre pressures for a second wheel set.Operation✱It is operated using the tyre pressure monitor button E226 on the centre console next to the gearstick. The button sends a signal as long as you hold it down. Depending on the state of the tyre pressure monitor system, the following procedures can be carried out according to how long you hold down the button:- Status query, - switch between full and partial loading, - switch on or off.S347_054✱Not for the North America region (NAR)39 TPM without position recognitionUse of button✱S347_006Time button heldup to 2 sec.3-7 sec.8-10 sec.11-15 sec.Actual state Required functions: Switch from full to partial loadingSwitchConfirmSwitch offMessages: “Tyre full load monitored” (gong)Messages: “Tyre part load on”Messages: When released: Gong confirms switchoverMessages:Switch from partial to full loading“Tyre full load monitored” (gong)“Tyre full load on”When released: Gong confirms switchoverSwitch on“Tyre check off” (gong)“Tyre part load on”When released: Gong confirms activationSwitch off“Tyre full load monitored” or “Tyre full load monitored” (gong)“Tyre part load on” or “Tyre full load on”“Tyre check off” (gong)Status queryFor example: “Tyre check off” or “Tyre full load monitored” (gong)After releasing: “Press ON switch longer” or “Press CHANGE or OFF longer”If the button is held for longer than 40 seconds or if it sticks, this will be entered in the fault memory.✱Not for the North America region (NAR)40 Tyre pressure warning lamp messagesStateVisual signalsAcoustic signalsText messages in dash panel insert displayIgnition on S347_005 2 seconds Soft warning:✱ Slight deviation from specified tyre pressure (0.3 to 0.4bar) None✱NoneNoneNone✱“Check tyre pressures” ✱ (for approx. 5 seconds after ignition switched on)Hard warning with gong: Greater deviation from specified tyre pressure (over 0.4bar) ... until specified tyre pressure is restored.Gong once“Tyre pressures too low” (hide with the multifunction display button)Hard warning with warning sound: sudden change to the tyre pressure (more than 0.2bar per minute)Warning tone once“Flat tyre”... until specified tyre pressure is restored.System fault or radio interferenceNoneNone... until the fault or the interference has been rectified.✱Not for the North America region (NAR)41 TPM without position recognitionFunction requirementsAs with the TPM with position recognition in the Phaeton and Touareg, the following requirements need to be met for the system in the Passat to work properly: 1. The driver has to inflate the tyres to the correct pressure also observing the different tyre pressures for full and partial loading. 2. External radio interference sources may not interfere with the wireless connection between wheel electronics and aerials. 3. The batteries in the wheel electronics should not have run flat. The life of the batteries is approx. 10 years.System overviewFurther information from the CAN data busE226 Tyre pressure monitor button✱J502 Tyre pressure monitor control unit (in convenience system central control unit J393)Convenience CAN data bus R47 G222 - G225 Tyre pressure sensors Central locking and anti-theft alarm system aerial K230 Tyre pressure warning lampJ285 Control unit with display in dash panel insert H3 Buzzer and gongS347_002✱Not for the North America region (NAR)42 Electrical componentsWheel electronicsThe wheel electronics or tyre pressure sensors do not have their own address words as their memories cannot be read separately using the VAS 5051/VAS 5052. Sent informationTemperature Tyre pressure AccelerationThe wheel electronics transfer the following information via the integrated individual sensors: - Tyre pressure, - tyre air temperature and - wheel acceleration.S347_066ID X 0 0 0 X X 0 X X X X X X X XControl bitStatusFurthermore the wheel electronics transfer the following additional information: - their own identification numbers (ID), - a control bit and - their own status. Signal use0 1Mode/ transferS347_074The signals from the wheel electronics are used by the tyre pressure monitor control unit J502 to analyse the tyre pressures and, if necessary, inform or warn the driver.Sensor failure Failure of wheel electronics is registered by the control unit. It creates an entry in the fault memory and a message for the driver.43 TPM without position recognitionUse of the individual information from the wheel electronicsTyre pressure Pressure changes in the tyres are recognised using the tyre pressure data. Tyre air temperature The tyre air temperature is used to evaluate the measured tyre pressure. Wheel acceleration The wheel acceleration data is compared with the current vehicle speed. Comparing the acceleration should prevent the tyre pressure monitor control unit J502 recognising wheel electronics from other vehicles as its own. Control bit The control bit allows the sensor to signal that it has recognised an internal fault. Status information Information on the wheel electronics mode and the cause of a data telegram transmission.Identification number Each wheel electronics unit has a ten-figure identification number (ID). This is included in each data transmission so that the information from the respective wheel electronics can be assigned. Adjacent you will find a schematic diagram of wheel electronics ID in the corresponding adjustment channels.Adjustment channel 10 1-4 0 0 1st number 2nd numberWheel numberAdjustment channel 11 0Placeholder3rd number4th number5th number6th numberPlaceholderAdjustment channel 12 0 7th number 8th number 9th number 10th numberPlaceholderS347_069ELSA provides the latest information.44 Wheel electronic modes The wheel electronic have various modes.There are the following modes:●Drive mode: The wheel electronics are active and send a data telegram every minute.S347_057●Sleep mode (also: test mode): The delivered state (sleep mode) of the wheel electronics is only active when the vehicle is delivered. The wheel electronics do not send any data telegrams. It switches to drive mode when the vehicle is driven faster than 25km/h for at least 4 minutes.S347_056●Park mode (energy saving mode): No data telegrams are sent, but the wheel electronics measure and are ready.S347_055●30B (30-block mode): The wheel electronics are currently in the mode , in which they send 30 data telegrams with a transmission interval of 15 seconds.S347_07545 TPM without position recognitionTyre pressure monitor button E226✱Function The tyre pressure monitor button E226 is a button with short-circuit to earth. When it is pressed, it will send a signal to the tyre pressure monitor control unit J502 (module convenience system central control unit) via a fixed line. Signal use Depending on the length of the signal sent, the driver’s requirements (switch on/off, status information, switch between partial/full loading) are recognised by the control unit and carried out. Effects upon failure An entry is made in the fault memory when the button fails.S347_011✱Not for the North America region (NAR)46 Tyre pressure monitor control unit J502The tyre pressure monitor control unit J502 is integrated in the convenience system central control unit and has its own diagnosis address with the address word 65. If the control unit fails and does not send data to the CAN data bus, the tyre pressure warning lamp K230 will be illuminated.S347_049When the convenience system central control unit J393 is updated or replaced (only TPM without position recognition), the following entries need to be made: - Coding of the system and - entry of the specified tyre pressures. ELSA provides detailed information on the procedure.47 TPM without position recognitionFunctional diagramJ519 J502 J393J533Outside temperature Speed signalE226✱ J285R47K230H3J119G222G223G224G225S347_004E226 G222 G223 G224 G225 H3 J119 J285 J393 J502 J519 J533Tyre pressure monitor button✱ Front left tyre pressure sensor Front right tyre pressure sensor Rear left tyre pressure sensor Rear right tyre pressure sensor Buzzer and gong Multifunction display (only on vehicles with multifunction display) Control unit with display in dash panel insert Convenience system central control unit Tyre pressure monitor control unit Onboard supply control unit Data bus diagnostic interfaceK230 R47Tyre pressure warning lamp Central locking and anti-theft alarm system aerialColour code/legend Input signal Output signal Positive Earth CAN data bus✱Not for the North America region (NAR)48 ServiceSets of tyres with other specified tyre pressuresIf a vehicle is fitted with tyres which require different specified tyre pressures to those specified inside the fuel filler flap, these tyres can also be monitored with the tyre pressure monitor (wheel set 2). Tyre pressures for a second set of tyre need to be set in the system using the VAS 5051/VAS 5052. The wheel electronics in the second set of wheels will not be recognised and learnt automatically by the tyre pressure monitor (like wheel electronics on the set of wheels with regular tyres). To switch to wheel set 2, you need to carry out the following work: - Read identification numbers (IDs) of wheel electronics (tyre pressure sensors) before fitting. - Switch the TPM to wheel set 2. - Enter the necessary specified tyre pressures and the IDs of the wheel electronics in the system.Adjustment channels- Adjustment channel 2: Switch monitoring from wheel set 1 to 2 and back - Adjustment channels 10 - 12: Enter wheel electronics IDs for wheel set 2 - Adjustment channel 5: Specified pressure full load axle 1 - Adjustment channel 6: Specified pressure partial load axle 1✱ - Adjustment channel 7: Specified pressure full load axle 2 - Adjustment channel 8: Specified pressure partial load axle 2✱Data blocks- Data block 25: Entry for which wheel set is being monitored. - Data block 23: Specified pressures wheel set 1 - Data block 24: Specified pressures wheel set 2✱Only the full load specified pressure is used for the North America region (NAR).If you go back to using wheels with the tyre pressures specified inside the fuel filler flap, this will have to be set again with the VAS 5051/VAS 5052 (wheel set 1). The wheels with wheel electronics are learnt automatically. The identification numbers do not have to be entered. ELSA provides detailed information on the procedure.49 TPM without position recognitionDetecting faulty wheel electronicsTyre pressure sensor no signal or faultyIn the tyre pressure monitor system without position recognition, the signals from the wheel electronics are received centrally from the central locking and antitheft alarm system aerial. Position assignment of the wheel electronics is therefore not possible.The following signs indicate a faulty wheel electronics unit: - A tyre pressure monitor system fault is displayed. - “No signal/communication tyre pressure sensor” or “Tyre pressure sensor faulty” is read from the fault memory.2.4 3.02.7 3.3To test one wheel electronics unit, you can proceed as follows:Approx. 1 25 km/h- Inflating the four tyres to four different pressures and noting the respective tyre pressures with the wheel position. - Moving the car for approx. one minute at more than 25km/h. - Read data blocks. If no tyre inside temperature and no current inflation pressure is included in the data block, the wheel electronics are faulty.Values missing in data block = wheel electronics faultyS347_062ELSA provides detailed information on the procedure.50 ServiceHandling the wheel electronics (TPM with/without position recognition)Fitting wheel electronics The wheel electronics are inserted from the inside through the wheel valve hole and screwed secure. Tyre changes with wheel electronics When changing tyres, make sure that the removal levers are not placed near the valves to avoid damage to the wheel electronics.Do not use removal levers in this areaChanging the wheel electronics The wheel electronics need to be replaced in the following situations: - Battery is flat. - The wheel electronics are faulty. - The valves are faulty (TPM without position recognition)S347_027If you use a tyre sealing fluid (Tirefit), we recommend changing the wheel electronics because the fluid can block the pressure sensor opening.Please use only approved valve inserts and original valve caps (no special caps) for the wheel electronics. The wheels may not be cleaned in cleaning machines that use ultrasound. Ultrasound can damage the wheel electronics. The valves are made from a specially coated aluminium for corrosion protection and can break off if you use too much force. The whole wheel electronics need to be replaced in this case.51 Test YourselfWhich answers are correct? One, several or all answers could be correct.1.What should you do first if a tyre problem occurs or the message “tyre pressure too low” is issued? a) Press the tyre pressure monitor button and start calibration or learning of the respective system. b) Drive slowly, avoid sharp steering movements and, at the next opportunity, stop and check the tyre pressure. c) Deactivate the tyre pressure monitor in the “Convenience Setup”.2.Which system does not need aerials in the wheel housings? a) Tyre pressure monitor with position recognition. The wheel electronics are connected to the tyre pressure monitor control unit via cables. b) Tyre pressure monitor display. The system is made up of a software module in the ABS control unit. No aerials are needed. c) Tyre pressure monitor system without position recognition. The signals from the wheel electronics are received centrally from the central locking and anti-theft alarm system aerial and forwarded.3.How can you tell whether a vehicle is equipped with a tyre pressure monitor system without position recognition? a) The tyre pressure monitor warning lamp in the dash panel insert illuminates for two seconds when you turn the ignition on. b) No rubber valves are installed in the wheels. c) The tool set does not include a jack.52 4.What do you have to observe when changing a wheel on a car with a tyre pressure monitor without position recognition to ensure that the system learns the new wheel electronics? a) The vehicle needs to be stationary for 3 minutes. b) The vehicle needs to be stationary for 20 minutes. c) The vehicle immediately needs to travel at a speed above 25km/h.5.When does the tyre pressure monitor button need to be pressed?✱ a) After one tyre has been inflated to the correct pressure. b) After more than one tyre has been inflated to the correct pressure. c) After each time the tyres are changed. d) After repair work on the chassis.✱Not for the North America region (NAR)53 Answers 1. b) 2. b, c) 3. a) 4. b) 5. a, b, c, d)54Test Yourself Notes55 347© VOLKSWAGEN AG, Wolfsburg All rights and rights to make technical alterations reserved. 000.2811.61.20 Technical status 08/2005 Volkswagen AG Service Training VK-21 Brieffach 1995 38436 Wolfsburg❀ This paper was manufactured from pulp that was bleached without the use of chlorine.