TECHNICAL DOCUMENTATION

SSP 360 The 3,2l and 3,6l FSI Engine

PDFEN72 pages7 MB
SSP 360 The 3,2l and 3,6l FSI Engine - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingSelf-study Programme 360The 3.2l and 3.6l FSI EngineDesign and Function The 3.2l, the 3.6l V6 FSI engine and the 3.6l V6 R36 FSI engine are VR engines. Having a smaller V-angle compared with a classic V engine, they have an extremely compact and space-saving design. VR engines have a long tradition at Volkswagen. The VR success story started in 1991 with the production start of the 2.8l VR6 engine. The VR5 engine followed in 1997 and the VR6 was changed to four-valve technology in 1999. In 2000, the displacement of the VR6 was raised to 3.2 litres allowing outputs of up to 184kW. The VR engines have a wide range of applications thanks to their compactness.This self-study programme was conceived for use within Volkswagen Group. For this reason, it does not describe the use of the engine in one particular vehicle. Where, however, a vehicle is referred to, it is only an example intended to help describe the design and functioning or to simplify the explanations.S360_057NEWImportant NoteThe self-study programme shows the design and function of new developments. The contents will not be updated.For current testing, adjustment and repair instructions, refer to the relevant service literature.2 ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Engine Mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Crankshaft drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Cylinder head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Camshaft adjustment system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Internal exhaust gas recirculation system . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Crankcase breather system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Intake manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Timing chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Poly V-belt drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Lubrication system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Cooling circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 FSI technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Engine Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 System overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Actuators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Control units for convenience CAN data bus . . . . . . . . . . . . . . . . . . . . . . . . 57Functional Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Special tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Test Yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 633 IntroductionS360_203The new 3.2l and 3.6l V6 FSI engines as well as the 3.6l V6 R36 engines are the three latest products in the VR engine range. While the 3.2l version is being used in the Volkswagen Passat for the first time in Europe, the 3.6l version is being launched in the Volkswagen Passat in North America. In Europe, the 3.6l V6 FSI engine will be available in the Audi Q7 and in the Volkswagen Touareg.Increasing the displacement to 3.2l and 3.6l and switching to FSI technology leads to a considerable increase in power and torque compared with the previous model. The 3.6l V6 R36 engine thus reaches a maximum rated power of 220kW and a maximum torque of 350Nm. The three compact engines have substantial power outputs and a dynamic torque band.4 Special features of the new V6 engines:● ● ● ● ●● ●●Outside dimensions have been kept the same FSI petrol direct injection Four-valve technology with roller rocker arms Internal exhaust gas recirculation Single-piece variable intake manifold made from plastic on 3.2l V6 FSI engine, two-piece variable intake manifold made from plastic on 3.6l V6 FSI engine and 3.6l V6 R36 engine Lightweight crankcase made from grey cast iron Camshaft driving chain with integrated drive for high-pressure fuel and vacuum pump Continuous inlet and exhaust camshaft timing adjustmentUsing the FSI direct injection technology allows the current emission levels EU4 and LEV2 to be fulfilled whilst saving fuel without secondary air injection.S360_2545 IntroductionTechnical data of 3.2l V6 FSI engineType Displacement Bore Stroke V angle Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel 6-cylinder VR engine 3168 cm3Power and torque development graphNm 400 360 320 280 240 200 kW 200 180 160 140 120 100 80 60 40 2086.0 mm 90.9 mm 10.6° 4 12 : 1 184kW at 6250 rpm 330Nm at 2750 – 3750 rpm Motronic MED 9.1 Super Plus unleaded at RON 98 (Super unleaded at RON 95 with reduction in performance) Two three-way catalytic converters with Lambda control EU4160 120 80Exhaust gas treatment401000 2000 3000 4000 5000 6000Emissions standardPower [kW] Torque [Nm]rpmS360_116Technical data of 3.6l V6 FSI engine (Touareg)Type Displacement Bore Stroke V angle Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel 6-cylinder VR engine 3597 cm 89 mm 96.4 mm 10.6° 4 12 : 1 206kW at 6200 rpm 360Nm at 2500 – 5000 rpm Motronic MED 9.1200 100 80 60 40 20 360 320 280 240 180 160 140 1203Power and torque development graphNm 400 kW 200Super Plus unleaded at RON 98 (Super unleaded at RON 95 with reduction in performance) Two three-way catalytic converters with Lambda control EU4, LEV2160 120 80Exhaust gas treatment401000 2000 3000 4000 5000 6000Emissions standardPower [kW] Torque [Nm]rpmS360_1156 Technical data of 3.6l V6 R36 engineType Displacement Bore Stroke V angle Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel 6-cylinder VR engine 3597 cm 89 mm 96.4 mm 10.6° 4 11.4 : 1 220kW at 6600 rpm 350Nm at 2400 – 5000 rpm Motronic MED 9.1200 100 80 60 40 20 360 320 280 240 180 160 140 1203Power and torque development graphNm 400 kW 200Super Plus unleaded at RON 98 (Super unleaded at RON 95 with reduction in performance) Two three-way catalytic converters with Lambda control EU4, LEV2160 120 80Exhaust gas treatment401000 2000 3000 4000 5000 6000Emissions standardPower [kW] Torque [Nm]rpmS360_4007 Engine MechanicsCrankshaft driveCylinder blockS360_004The cylinder block has been extensively revised compared with the 3.2l multi-point injection engine. The aim of the revision was to achieve a displacement of 3.6l without changing the outside dimensions of the engine. This aim was reached by changing the V-angle and the offset. All three FSI engines, the 3.2l, the 3.6l engine and the 3.6l R36 engine have the new cylinder block. It is made from grey cast iron with lamellar graphite.Further new features compared with 3.2l multi-point injection engine: - The oil pump is integrated in the cylinder block. - Greater oil return from the cylinder block into the oil sump - Improved stiffness of cylinder block combined with weight reductions - In the cylinder block, the volume of coolant has been reduced by 0.7 litres. This allows the coolant to heat up faster.8 V angle 10.6° Cylinder longitudinal axisS360_003 Crankshaft centre axis 22mm OffsetThe V angle The V angle of the cylinder block is 10.6°. Changing the V angle from 15° to 10.6° has allowed the necessary cylinder wall thickness to be ensured without having to change the dimensions of the engine.Offset Reducing the V angle has moved the cylinder longitudinal axis to the outside at the bottom compared with the crankshaft. The spacing of the cylinder longitudinal axis from the crankshaft centre axis is the offset. The offset has been increased from 12.5mm to 22mm compared with the multi-point injection engine.9 Engine MechanicsAbradable coatingPiston recessS360_001The crankshaftThe crankshaft is made from grey cast iron and is mounted on 7 bearings like the 3.2l multi-point injection engine.The connecting rodThe connecting rods are cut, not fracture-split. The connecting rod eye is trapezoidal. The big end bearings are coated with molybdenum. As a result, they have good run-in properties and are highly durableThe pistonsThe pistons are recess-type and made from an aluminium alloy. They have a graphite abradable coating on the side to improve the run-in properties. The pistons for cylinder bank 1 and cylinder bank 2 are different. The difference is in the arrangement of the valve pockets and the combustion chamber recess. The injected fuel is swirled and mixed with the intake air due to the position and shape of the piston recess.10 Cylinder headInjection valves 1, 3, 5S360_006Injection valves 2, 4, 6S360_330 Location of vacuum pumpLocation of high-pressure fuel pump S360_007The cylinder head is made from an aluminium/ silicon/copper alloy and is identical on the three engines. It is a new design due to the direct injection. The cylinder head has been made longer to accommodate the camshaft timing chain and for a fixed connection of the high-pressure fuel pump and the vacuum pump. The injection valves for both cylinder banks are on the intake side of the cylinder head.The bores for the injection valves on cylinders 1, 3 and 5 are above the intake manifold flange. The injection valves for cylinders 2, 4 and 6 are inserted underneath the intake manifold flange. In this arrangement, the injection valves for cylinders 1, 3 and 5 run through the intake ports of the cylinder head. To compensate for the influence of the injectors on the flow behaviour in the intake port, the valve spacing for all cylinders has been increased from 34.5 to 36.5mm. Therefore, when the cylinders are filled, flow diversion by the injection valves is minimised.Please note that, due to the two different insertion positions for the injectors, two different injector lengths are also required.11 Engine MechanicsCamshaft adjustment systemInlet camshaft vane adjuster Outlet camshaft vane adjusterS360_012N318 Exhaust camshaft control valve 1 N205 Inlet camshaft control valve 1The adjustment of the camshafts allows the power and the torque to be increased as well as consumption and emissions to be reduced depending on the load behaviour of the engine. The camshafts are adjusted by two vane adjusters. Both camshafts can be continuously adjusted in the direction of early opening and in the direction of late opening of the valves. The engine control unit controls the following solenoid valves to adjust the camshafts: - N205 Inlet camshaft control valve 1 and - N318 Exhaust camshaft control valve 1Maximum adjustment of the camshafts: - Inlet camshaft 52° crank angle and - exhaust camshaft 42° crank angle Both camshaft adjusters are adjusted using two camshaft control valves with the aid of the engine oil pressure. Adjusting both camshafts allows a maximum valve overlap of 42° crank angle. The valve overlap creates an internal exhaust gas return.12 Internal exhaust gas recirculation systemIntake manifold vacuum Exhaust valve Inlet valve Inlet valve open Exhaust valve closeTDCValve overlapStroke 4 BDC Stroke 2 S360_124Stroke 1 Stroke 3The internal exhaust gas recirculation counteracts the formation of nitrogen oxide NOx . As with the external exhaust gas recirculation system the reduced formation of NOx results from the combustion temperature being reduced by feeding in combustion gases. There is a slight shortage of oxygen due to the combustion gases in the fresh fuel-air mixture. As a result the combustion is not as hot as when there is excess oxygen. Nitrogen oxide is only formed in large concentrations above a relatively high temperature. The formation of NOx is reduced by lowering the combustion temperature in the engine and by creating a shortage of oxygen.How it works During the exhaust stroke the inlet and exhaust valves are open. Due to the high intake manifold vacuum, some of the combustion gases from the combustion chamber are drawn into the intake port and fed back into the combustion chamber for the next combustion. Advantages of internal exhaust gas return: - Fuel consumption saving due to reduced charge changing process - Larger partial load range with exhaust recirculation - Smoother running - Exhaust gas recirculation possible when engine is still cold13 Engine MechanicsCrankcase breather systemIt prevents vapours enriched with hydrocarbons (blow-by gases) reaching the outside atmosphere from the crankcase. The crankcase breather system consists of vent ducts in the cylinder block and cylinder head, the cyclonic oil separator and the crankcase breather heating. How it works The blow-by gases in the crankcase are drawn in by the intake manifold vacuum via: the vent ducts in the cylinder block, the vent ducts in the cylinder head, the cyclonic oil separator, the pressure limiting valve and the crankcase breather heatingCyclonic oil separator Crankcase S360_332 breather heatingand then fed back into the intake manifold.S360_253 Vent ducts in cylinder block and in cylinder headCyclonic oil separator The cyclonic oil separator is in the cylinder head cover. It has the task of separating oil from the blowby gases in the crankcase and feeding it back to the oil system. A pressure control valve limits the intake manifold vacuum from approx. 700mbar to approx. 40mbar. It prevents the same vacuum forming as in the intake manifold and thus engine oil being drawn in via the crankcase breather or seals being damaged.Cyclonic oil separatorPressure control valveS360_058 Oil outletto intake manifold14 How it works The cyclonic oil separator separates the oil from the oil vapours drawn in. It works according to the principle of centrifugal separation. Due to the cyclonic design of the oil separator, the oil vapours are set in a spinning movement. The centrifugal force produced propels the oil onto the separator wall where it forms larger drops. While the separated oil drips into the cylinder head, the gas particles are fed into the intake manifold via a flexible pipe.Cyclonic oil separatorPressure control valve Oil outletIntake manifold S360_025Inlet Gas outlet to intake manifold Gas particlesOil droplets S360_059 Oil outlet opening in the crankcaseIf the pressure control valve is faulty, the pressure inside the crankcase corresponds with the intake manifold vacuum. As a result, a very large amount of oil is drawn out of the crankcase via the crankcase breather possibly causing damage to the engine.Flexible hoseCrankcase breather heating The heating element is inserted in the flexible hose that runs from the cyclonic oil separator to the intake manifold and is screwed to the intake manifold. The crankcase breather heating prevents the blow-by gases freezing when the intake air is very cold.S360_026 Heating element15 Engine MechanicsIntake manifoldThe 3.2l V6 FSI engine has a single-piece overhead variable intake manifold made from plastic. The 3.6l V6 FSI engine and the 3.6l V6 R36 FSI engine have been given a two-piece intake manifold made from plastic. In the Touareg, it is a variable intake manifold.One-piece variable intake manifold on 3.2l V6 FSI engineChange-over shaft with flaps Short resonance pipe Power collector Long resonance pipe Torque collector Crankcase breatherS360_021 Throttle valve control unitDesignThe 3.2l V6 FSI engine intake manifold consists of: - the torque collector, - two resonance pipes with different lengths for each cylinder, - the change-over shaft, - the power collector - the vacuum reservoir and - the intake manifold flap valve. The two resonance pipes have different lengths because a long resonance pipe is required to reach a high torque and a short resonance pipe is required to attain high power. The change-over shaft opens and closes the connection to the power collector.16 Change-over flaps The system switches between power and torque setting with change-over flaps. The change-over flaps are operated by engine control unit J623 via the intake manifold flap valve N316 by means of vacuum. When the valve is not powered, the flaps are open and thus in the power position.N316 Change-over flapsS360_022Vacuum reservoirVacuum reservoirS360_061 Check valve Torque collectorThere is a vacuum reservoir inside the intake manifold in which a vacuum supply is kept ready to operate the change-over flaps. The air from the vacuum reservoir is drawn off via a check valve in the torque collector so that a vacuum builds up in the vacuum reservoir. If the check valve is faulty, the change-over flaps can no longer be operated.J623N316S360_06017 Engine MechanicsHow the variable intake manifold worksThe variable intake manifold works according to the principle of resonance charging and is designed so the valve timing, the intake strokes and the air oscillation is rhythmic. This leads to an increase in pressure in the cylinder and thus to good filling of the cylinders.Power position of the variable intake manifold Power collectorTorque position of the variable intake manifoldVariable intake manifold housingAir flow from the power collector Change-over shaft S360_063 Change-over shaftAir flow from the intake manifold S360_062Engine speed from 0 to approx. 1200 rpm The variable intake manifold is in the power position. The intake manifold flap valve is not powered. The vacuum wave created from the start of the intake process is reflected at the end of the power pipe and returns to the intake valve after a brief time.Engine speed between approx. 1200 and approx. 4000 rpm The intake manifold flap valve is powered by the engine control unit. The change-over flaps and thus the power pipes are closed. The cylinders draw in the air directly from the torque collector through the torque pipes.Engine speed above approx. 4000 rpm. The intake manifold flap valve is not powered. As a result, the intake manifold flaps switch to the power position again.You will find more detailed information on the design and function of resonance-pipe variable intake manifolds in self-study programme 212 “Variable Intake Manifold in VR Engines”.18 Two-piece intake manifold on 3.6l V6 FSI engineWhile the 3.2l V6 FSI engine has kept the single-piece variable intake manifold, a two-piece plastic intake manifold will be used from model year 2007 for the 3.6l V6 FSI engine in the Passat and R36. This manifold is not variable, but meets the requirements for power and torque in the different rev ranges with a modified duct geometry.Compared with the 3.2l engine, there is no electric valve for intake manifold flap in the engine management and no vacuum control element with switching valve on the intake manifold.S360_348The two-piece intake manifold is made up of an upper part and a lower part that are screwed to each other. Splitting the intake manifold into two segments simplifies assembly and allows access to the components under the intake manifold.Upper part of intake manifold Lower part of intake manifold S360_36019 Engine MechanicsTwo-piece intake manifold on 3.6l V6 FSI engineThe 3.6l V6 FSI engine is equipped with a variable intake manifold specially for use in the Touareg. It is based on the two-piece plastic intake manifold from the 3.6l V6 FSI engine. The intake manifold geometry has been adapted to the special power and torque requirements of this engine and a resonance flap has been added. The resonance flap is operated as normal with a vacuum control element and the electrical valve for intake manifold flap that opens or closes the connection between the vacuum system and the vacuum control element and thus indirectly operates the resonance flap. The variable intake manifold works according to the principle of combined oscillation pipe and resonance charging. By combining both charging techniques, dynamic charging over a broader rev range can be achieved.S360_334 Vacuum control element Valve for intake manifold flapResonance flapS360_336DesignTorque collector Throttle valveThe variable intake manifold comprises: the torque collector, the resonance pipes the resonance chamber, the power pipes the resonance flap the vacuum control element and the intake manifold flap valve.Resonance pipesResonance chamberPower pipes S360_362Resonance flap20 How the variable intake manifold worksFor the first time, VW is using a variable intake manifold that works on the principle of resonance charging. Resonance charging means self-charging with pressure oscillations in resonance pipes that are open on both sides. Whereas in oscillation pipe charging only the pressure oscillation is used in the intake manifolds, the cylinders are charged by means of pressure increases in resonance charging. The piston movement causes a certain excitation frequency to be produced in the intake. If it coincides with the eigenfrequency of the configured resonance systems, a charging effect occurs due to resonance peaks, i.e. the cylinders are filled better with the fresh air required to burn the fuel.lRdRVRVRThe engine speed at which the resonance charging occurs can be influenced with the design of the variable intake manifold. This means that the resonance charging is dependent on the resonance pipe length, the pipe diameter and the resonance chamber volume. Resonance charging works ideally with 3, 6 or 12 cylinder engines. One requirement is that the intake cycles of the cylinders are shifted 240° so that they do not overlap and weaken each other.S360_368lR - Length of resonance pipe dR - Diameter of resonance pipe VR - Volume of resonance chamberAs the engine speed range at which the resonance peaks occur is very narrow, pure resonance intake systems are rarely used. By combining both charging techniques, oscillation pipe charging and resonance charging, dynamic charging over a broader rev range can be achieved.How the two-piece variable intake pipe works The two-piece variable intake manifold works according to the principle of resonance charging up to approx. 4500 rpm (torque position of the variable intake manifold). Above 4500 rpm, the variable intake manifold is in power position and charging uses the principle of oscillation pipe charging via the short power pipes.21 Engine MechanicsResonance charging The cylinders of the 3.6 l V6 FSI engine are divided into two groups of three cylinders when the resonance flap is closed. There are therefore two resonance systems. One resonance system is formed by three cylinders with 240° CA offset intake phases that do not have timing overlaps. The groups of cylinders with the same firing intervals are connected to the resonance chambers and resonance pipes via individual resonance pipes (power pipes). Oscillation pipe charging At higher rev ranges, there is a switch-over from resonance system to oscillation pipe system. Opening the resonance flap creates one large chamber out of the two chamber halves. This doubles the volume of the chamber. The eigenfrequency of the resonance system is shifted to lower revs. In the rev range from 4500 rpm, there is no resonance excitation so that the dynamic charging now occurs from the open resonance chamber through the short power pipes that act as oscillation pipes.Torque position of the variable intake manifoldPower position of the variable intake manifold Throttle valveResonance pipes Resonance chamber Resonance flapPower pipes S360_364 Resonance system 2 Resonance system 1 S360_36622 Chain driveInlet camshaft drive Outlet camshaft driveHighpressure fuel pump and vacuum pumpHydraulic chain tensionerOil pump drive Camshaft roller chainPrimary roller chainHydraulic chain tensioner Crankshaft sprocket S360_016The chain drive is located on the gearbox side of the engine. It is made up of the primary roller chain and the camshaft roller chain. The primary roller chain is driven by the crankshaft. It drives the camshaft roller chain and the oil pump via a sprocket.The camshaft roller chain drives the two camshafts and the high-pressure fuel pump. Both chains are held at the precise chain tension by hydraulic chain tensioners.Please refer to the current workshop manual for information on setting the timing. There is a new special tool T10332 for locking the high-pressure fuel pump sprocket.23 Engine MechanicsVacuum pumpA mechanical vacuum pump is fitted instead of the electrical vacuum pump on the Touareg with 3.6l engine and automatic gearbox. The vacuum pump ensures that sufficient vacuum can be maintained for all consumers that are connected to the engine vacuum system even at low revs.Rear viewFitting for square end of drive shaftS360_340 Mechanical vacuum pump S360_370The vacuum pump is driven together with the highpressure fuel pump via the engine chain drive. The drive shaft of the high-pressure fuel pump has been extended for this. The vacuum pump meshes into the square end of the drive shaft. The vacuum pump housing is bolted to the cylinder head.Extended drive shaftS360_37224 Poly V-belt driveTensioning pulleyCoolant pump driveAlternator drivePoly V-belt pulley on crankshaftGuide rollerAir-conditioning compressor driveGuide roller S360_015Structure of poly VbeltOuter fabric layer Top layer Polyester cordS360_342 Poly V-belt pulley on 3.6l V6 R36 FSI engine S360_170 Base Poly V-belt pulleyA one-sided poly V-belt is used. It runs quietly and free of vibration even at high speeds. The belt is driven by the crankshaft via the poly V-belt pulley with vibration damper. On the 3.6l V6 R36 FSI engine, it is fastened to the crankshaft with seven screws due to the greater forces and moments.The air-conditioning compressor, the alternator and the coolant pump are driven by the belt. The poly V-belt is constantly held at the correct tension by a belt tensioner.25 Engine MechanicsOil systemCamshaft adjuster Hydraulic valve lifters Camshaft bearing High-pressure fuel pump drive Chain tensioner Chain tensioner Oil reservoir Oil pump Camshaft adjusterVacuum pump Jets for piston lubricationOil reservoirCrankshaft bearing Intake port Oil return Oil filter/cooler moduleOil sump S360_352The oil pressure is generated by a self-priming duocentric oil pump. It is built into the cylinder block and is driven by the chain. The oil supply path is longer due to the position, which is disadvantageous for the initial oil supply of the components. For this reason, to ensure initial oil supply, oil is taken from an oil reservoir located behind the oil pump.The oil pump draws the oil out of the oil sump and delivers it to the oil filter/cooler module. It is cleaned there and cooled before it is forwarded to the engine lubrication points.26 Oil pump with oil reservoir The oil reservoir is formed by a hollow space in the cylinder block behind the oil pump. It has a volume of approx. 280ml and remains filled after the engine is switched off.Cylinder headOil reservoirDrive gearService access Oil pumpCylinder block S360_174Service access for oil pump The service access allows you to reach the oil pressure relief valve of the oil pump while the engine is installed in the vehicle. After removing the cover bolt and a second bolt inside, you can remove the oil pump pressure relief valve through this opening and check its condition without having to remove the chain drive.S360_052Cover boltpressure relief valveS360_05627 Engine MechanicsOil filter/cooler module The oil filter/cooler module is made up of oil filter, oil cooler, anti-drain valve and by-pass valve.Oil filter/cooler module on PassatIt is located on the engine and, on some vehicle types and engine mounting positions, it is also designed as an engine mount.Oil coolerS360_019 Oil filterOil return The returned oil runs into a central oil return channel in the cylinder block via three return ducts in the cylinder head. The oil then flows back into the oil sump below the oil level. In addition to the central oil return, oil runs into the sump via the camshaft timing chain shaft.Oil returnS360_21928 Cooling circuitLegend 1 Expansion tank 2 Heat exchanger for heating 3 Coolant pump 4 Gearbox oil cooler 5 Thermostat 6 Oil cooler 7 Check valve 8 Circulation pump V55 9 Check valve 10 Auxiliary cooler 11 Cooler12345 6 789 10 11 S360_401The coolant is circulated by the mechanical coolant pump. It is driven by the poly V-belt. The coolant circuit contains 9 litres of coolant. Compared with the 3.2l multi-point injection engine, the total coolant quantity has been reduced by 2 litres. This allows the engine to reach its operating temperature faster. The circuit is controlled by the expansion-type thermostat.Depending on the vehicle, an auxiliary cooler may be integrated in the coolant circuit (10). The one way valves are integrated into the coolant circuit so that they prevent backflow of the coolant.29 Engine MechanicsCirculation pump V55 is an electric pump. It is integrated in the engine coolant circuit and is controlled by the engine control using a map. After parking the vehicle and when there is no air flow, it is switched on at a certain coolant temperature.S360_169Radiator fan The V6 FSI engine uses two electric radiator fans. The radiator fans are controlled by the engine control unit as required. The engine control unit J623 signals to the radiator fan control unit J293 when the radiator fan is needed. The control unit J293 then supplies power to one or both of the fans as required. The power from control unit J293 is supplied via the Motronic current supply relay J271 and onboard supply control unit J519. The fans can be switched on by the radiator fan control unit even after the vehicle has been parked. The radiator fan control unit has a connection to terminal 30 to switch the fans on when the vehicle has been parked.Engine control unit J623Radiator fan V7Radiator fan 2 V177 Motronic current supply relay J271 S360_171 S S Terminal 30Onboard supply control unit J519Radiator fan control unit J29330 Exhaust system3.2l V6 FSI engineG39 Main catalytic converter G130S360_117 G108 G131The exhaust system for the 3.2l engine has a main catalytic converter with ceramic substrate for each bank. The exhaust gas quality is monitored by two Lambda probes in front of and behind the catalytic converters. The exhaust gas system fulfils emission level EU4. 3.6l V6 FSI engineG39 Starter catalytic converter G130 Main catalytic converterS360_118 G131 G108The exhaust gas system on the 3.6l FSI engine is equipped with two starter catalytic converters and two main catalytic converters. The exhaust gas quality is monitored by Lambda probes in front of the catalytic converter and two Lambda probes after the starter catalytic converter. The exhaust system fulfils emission level EU4 and LEV2 (Low Emission Vehicles).31 Engine Mechanics3.6l V6 R36 engineG39 Main catalytic converter G130S360_117 G108 G131The exhaust system for the 3.6l V6 R36 FSI engine is the same as the system for the 3.2l V6 FSI engine. The pipe and connection cross-sections in the system have been adapted to the needs of the R36 engine.Therefore, when carrying out repairs, check that the replacement parts are correct for the engine.32 FSI technologyInfluencing variables: - System pressure - Injection start - Injection end - Channel shape - Air flow- Valve timing - Valve stroke - Valve diameter- Fuel flow - Jet cone - Jet angle- Recess shape- Stroke - Bore - RPMS360_035Direct petrol injection requires precise tuning of the combustion process. The following are influencing variables on the combustion process: the cylinder bore and stroke, the shape of the recess in the piston surface, the valve diameter and stroke, the valve timing, the geometry of the intake ports, the amount of air supplied, the characteristics of the injectors (jet cone, jet angle, flow quantity, system pressure and valve timing) as well as - the engine speed. Investigations of the flow behaviour in the combustion chamber are an essential part of combustion process optimisation. The flow behaviour of intake air and injected fuel influences the mixture formation considerably.The Doppler Global Velocimetry method was used to determine the optimum flow behaviour and thus determine the optimum piston design for both cylinder banks. This method allows the flow behaviour and thus the mixture formation to be investigated while the engine is running. Using this method and the adaptation of the injector characteristics, the flow speeds and the mixture formation in the combustion chambers of the two cylinder banks can be configured in the same way and be tuned to each other. The engine runs only in homogeneous mode. The homogeneous split catalytic converter heating method for heating the catalytic converter is new.33 Engine MechanicsFuel systemG6 Fuel system pressurisation pump G247 Fuel pressure sender G410 Fuel pressure sender for low pressure J538 Fuel pump control unit J623 Engine control unit N276 Fuel pressure regulating valve Low-pressure lineLow-pressure fuel systemThe low-pressure system delivers fuel from the fuel tank. The fuel system pressurisation pump is operated by the engine control unit via the fuel pump control unit at an operating pressure between 2 and 5bar as required.G6Pressure limiting valveFuel filterPressure relief valveHow it works The signal from the fuel pressure sender for low pressure G410 constantly indicates the current fuel pressure for the engine control unit. The fuel pressure sender for low pressure N410 is screwed into the low-pressure line from model year 2007. Before model year 2007, the sender is on the high-pressure fuel pump. The engine control unit compares the current pressure with the current fuel pressure requirement. If the current fuel pressure is not sufficient to cover this fuel requirement, the engine control unit sends a signal to the fuel pump control unit J538. This then sends a signal to the fuel system pressurisation pump that raises the operating pressure. When the fuel requirement decreases again, the working pressure of the pump will be reduced accordingly. The pressure relief valve holds the fuel pressure when the engine is turned off. If the fuel line is broken in an accident, the pressure relief valve prevents the fuel leaking. The pressure limiting valve opens at a pressure of 6.4bar and thus prevents the fuel pressure in the lowpressure line becoming too high. The extra fuel then flows into the reservoir chamber.34 G410Pressure limiting valve High-pressure fuel pump High-pressure line Injector cylinder 1 Injector cylinder 3 Injector cylinder 5 Fuel rail cylinder bank 1N276 Fuel rail cylinder bank 2 G247 J623 Injector cylinder 2 Injector cylinder 4 Injector cylinder 6J538S360_402High-pressure fuel systemThe fuel pressure sender G247 is mounted on the fuel rail for cylinder bank 2 and informs the engine control unit about the current pressure in the high-pressure fuel system. The pressure limiting valve is on the fuel rail for cylinder bank 1. The valve opens a connection to the low-pressure fuel system when the fuel pressure in the high pressure system rises above 120 bar.The fuel pressure regulating valve N276 is screwed into the high-pressure fuel pump and regulates the pressure in the high-pressure fuel system depending on the signal from the engine control unit.35 Engine MechanicsThe high-pressure fuel pumpLow-pressure fuel lineis located on the cylinder head and is a piston pump. It is driven by the camshaft and produces a maximum fuel pressure of 105bar.High-pressure fuel lineHigh-pressure fuel pumpFuel pressure regulating valve N276 S360_346High-pressure fuel pump drive The high-pressure fuel pump is driven by a sprocket with double cam. The double cam operates the pump piston that generates the high pressure via a roller.Sprocket High-pressure fuel pump Pump piston Cylinder head Tappet Roller Double cam Sprocket Drive tappet for fuel pump Double cam S360_354 S360_173The high-pressure fuel pump sprocket needs to be locked using special tool T10332 when the camshaft roller chain is fitted. You will find more information on the high-pressure fuel pump in self-study programme 296 “The 1.4 ltr. and 1.6 ltr. FSI engine with timing chain”.36 Injector characteristicsOutlet valve Inlet valveInjection valve Piston recessThe piston recesses need to have different shapes as the injectors are fitted on the same side on both cylinder banks. This is necessary because the injectors and intake valves on both cylinder banks are arranged at different angles. In addition to the injection quantity and the injection duration, the shape and direction of the fuel jet plays an important part.Valve angle cylinders 1, 3, 5S360_252Valve pocketValve angle cylinders 2, 4, 6S360_251Homogeneous split catalytic converter heating methodLate pilot injection Later ignition timeCatalytic converterS360_159 Hotter combustion gases heat up the catalytic converter.This system has the task of quickly heating the catalytic converters to operating temperature for cold starts. Fuel is injected twice in a combustion stroke. The first injection occurs in the intake stroke. This creates an even distribution of the fuel/air mixture. In the second injection, a small additional amount of fuel is injected just before ignition TDC. The late injection increases the exhaust gas temperature. The hot exhaust gas heats up the catalytic converter so that it reaches its operating temperature faster.37 Engine ManagementSystem overviewSensors Engine speed sender G28 Air mass meter G70 Accelerator position sender G79 Accelerator position sender 2 G185Clutch position sender G476 Throttle valve module J338 with throttle valve drive angle sender 1 for electric throttle G187 Throttle valve drive angle sender 2 for electric throttle G188Engine control unit J623Hall sender G40 Hall sender 2 G163 Coolant temperature sender G62 Radiator outlet coolant temperature sender G83 Knock sensor 1 G61 Knock sensor 2 G66Brake light switch FFuel pressure sender G247Fuel pressure sender for low pressure G410 Powertrain CAN data busOil level and oil temperature sender G266 Lambda probe G39 Lambda probe 2 G108 Lambda probe after catalytic converterG130 Lambda probe 2 after catalytic converter G131S360_15438 Actuators Fuel pump control unit J538 Fuel system pressurisation pump G6Injectors for cylinders 1-6 N30, N31, N32, N33, N83, N84Ignition coils 1 -6 with output stage N70, N127, N291, N292, N323, N324Throttle valve module J338 with throttle valve drive for electric throttle G186Fuel pressure regulating valve N276 Active charcoal filter system solenoid valve N80 Valve for intake manifold flap N316 Inlet camshaft control valve 1 N205 Exhaust camshaft control valve 1 N318 Control unit with display in dash panel insert J285 Lambda probe heater Z19 Lambda probe 2 heater Z28 Lambda probe 1 heater after catalytic converter Z29 Lambda probe 2 heater after catalytic converter Z30Radiator fan control unit J293 Radiator fan V7 Radiator fan 2 V177 Circulation pump relay J160 Circulation pump V55S360_15539 Engine ManagementSensorsThe engine speed sender G28is bolted to the side of the cylinder block. It monitors the sender wheel on the crankshaft.Signal use The engine speed and the precise position of the crankshaft compared with the camshaft are determined with the signal from the engine speed sender. This information is used to calculate the injection quantity and the start of injection.S360_111Effects of signal failure In the event of signal failure, the engine is shut off and can no longer be started.40 Air mass meter G70In the 3.2l and 3.6l FSI engine, the hot-film air mass meter from the 6th generation (HFM6) is used. It is located in the engine intake duct and uses a thermal measuring principle like its predecessor. It characteristics:●● ● ●a micro-mechanical sensor element with return flow detection, signal processing with temperature compensation, high measuring accuracy and high sensor stability.ConnectorSensor electronicsIntake airS360_183 Bypass channel41 Engine ManagementHow it works The sensor element of the air-mass meter protrudes into the flow of intake air drawn in by the engine. Part of the air flows through the bypass channel in the air mass meter. The sensor electronics are in the bypass channel. A heating resistor and two temperature sensors are integrated in the sensor electronics. The two temperature sensors recognise the direction of air flow:S360_178 Measurement of the intake air Cut-out of air mass meter- intake air passes temperature sensor 1 first and - air flowing back from the closed valves passes temperature sensor 2 first. In conjunction with the heating resistor, the engine control unit can determine the oxygen content of the intake air.Sensor elementHeating resistor Temperature sensor 1 S360_179 Flow of intake airSignal use The signal from the air mass meter is used by the engine control unit to calculate the volumetric efficiency. The control unit calculates the engine torque with the volumetric efficiency taking the Lambda value and the ignition time into consideration. Effects of signal failureS360_180 Measurement of returning air when valves closedIf the air mass meter fails, the engine management calculates a substitute value.Returning airTemperature sensor 2 Heating resistor S360_181You will find more information on how the air mass meter G70 works and its measuring principle in self-study programmes 358 “Hot-film Air-mass Meter HFM 6” and 195 “The 2.3 ltr. V5 engine”.42 Accelerator position sender G79 and accelerator position sender 2 G185The two accelerator position senders are part of the accelerator pedal module and work contactless. The engine control unit recognises the driver’s wishes with the signals from these sensors. Signal useG79 and G185The engine control unit uses the signals from the accelerator position sender to calculate the injection quantity.Accelerator pedalEffects of signal failure If one or both senders fail, an entry is made in the fault memory and the electronic power control fault lamp illuminates. The convenience functions, for example, the cruise control or the engine braking control, are switched off.S360_150Clutch position sender G476This is a mechanically operated switch that is located on the clutch pedal. The clutch position sender is only required on vehicles with manual gearbox.Clutch pedal module Sender cylinderSignal use The signal is required to control the cruise control and to control the ignition advance and injection quantity when changing gear.Effects of signal failureG476The cruise control cannot be switched on. There are driveability problems like engine judder and raised engine speed when changing gear.S360_16343 Engine ManagementAngle sender 1 G187 and angle sender 2 G188 in the throttle valve moduleThese senders determine the current position of the throttle valve and send this information to the engine control unit.Signal use The engine control unit recognises the position of the throttle valve by the throttle angle sender signals. The signals from both senders are redundant. This means that both senders supply the same signal for reasons of driving safety.Throttle valve housingThrottle valve drive S250_238Throttle valveG187 and G188Effects of signal failure Example 1 The engine control unit receives an implausible signal or no signal from an angle sender: - An entry is made in the fault memory and the electronic power control fault lamp illuminates. - Subsystems that influence the torque (e.g. cruise control or engine braking control) are switched off. - The load signal is used to check the other angle sender. - The accelerator pedal responds normally. Example 2 The engine control unit receives an implausible signal or no signal from both angle senders: - An entry is made in the fault memory for both senders and the electronic power control fault lamp illuminates. - The throttle valve drive is switched off. - The engine will only run with an increased idle speed of 1500 rpm and will no longer respond to the accelerator pedal.44 Hall senders G40 and G163Both Hall senders are located in the engine timing chain cover. They have the task of informing the engine control unit about the position of the intake and exhaust camshafts. They monitor a quick-start sender wheel, which is on the respective camshaft. Using Hall sender G40, the engine control unit recognises the position of the intake camshaft and, using Hall sender 2 G163, the position of the exhaust camshaft.G40G163S360_356Signal use The signal from the Hall sender allows the exact position of the camshaft compared with the crankshaft to be recognised when the engine is started. Together with the signal from the engine speed sender G28, the system recognises which cylinder is at ignition TDC. This allows the system to inject and ignite precisely in the corresponding cylinder.Effects of signal failure If the signal fails, the signal from the engine speed sender G28 will be used. It may take longer to start the engine since the camshaft position and the crank position cannot be determined so quickly.45 Engine ManagementCoolant temperature sender G62This sender is on the coolant pump above the oil filter on the engine and informs the engine control unit about the coolant temperature. Signal use The coolant temperature is used by the engine control unit for various engine functions. For example, the injection quantity is calculated, the charge air pressure, the start of transport and the exhaust gas recirculation amount. Effects of signal failureS360_164If the signal fails, the engine control unit will use the signal from the coolant temperature sender G83.G62Radiator outlet coolant temperature sender G83Radiator inletThe coolant temperature sender G83 is in the hose on the radiator outlet and measures the temperature of the coolant leaving the radiator. Signal use The radiator fan is controlled by comparing both signals from the coolant temperature senders G62 and G83. Effects of signal failure If the signal from the coolant temperature sender G83 fails, radiator fan speed 1 is activated constantly.Radiator outletG83S360_18246 Knock sensors G61 and G66The knock sensors are bolted to the crankcase. They recognise engine knock in the individual cylinders. To avoid engine knock, individual cylinder knock control takes over the electronic control of the ignition timing.S360_157 G61 G66S360_158Signal use Using the signals from the knock sensors, the engine control unit adjusts the ignition angle until there is no longer engine knock.Effects of signal failure If a knock sensor fails, the ignition angles of the affected cylinder group are cancelled. Then a retarded, default ignition angle is used. This can lead to an increase in fuel consumption. The knock control for the cylinder group of the other functioning knock sensor continues. If both knock sensors fail, the engine management will switch to knock control limp-home mode, in which the ignition angles are retarded. The full engine performance will then no longer be available.47 Engine ManagementBrake light switch FThe brake light switch is on the tandem master cylinder and monitors a magnetic ring on the tandem master cylinder piston contact-free using a Hall element. The switch sends the “brake pressed” signal to the engine control unit via the powertrain CAN data bus.360_177Signal use The cruise control is switched off when the brake is pressed. If first “accelerator pedal pressed” and also “brake pressed” is recognised, the system switches to a higher idling speed.Effects of signal failure If the sender signal fails, the injection quantity is reduced and the engine has less performance. The cruise control system is also switched off.Fuel pressure sender for high pressure G247This sender is located on the lower fuel rail and measures the fuel pressure in the high-pressure fuel system. Signal use The engine control unit evaluates the signal and regulates the fuel high pressure using the fuel pressure regulating valve N276 in the high-pressure pump. Effects of signal failure If the fuel pressure sender fails, the fuel pressure regulating valve is controlled by the engine control unit with a fixed value.G247S360_34448 Fuel pressure sender for low pressure G410The fuel pressure sender for low pressure is on the low-pressure line and measures the fuel pressure in the low-pressure fuel system. Signal use The signal is used by the engine control unit to regulate the low-pressure fuel system. Following the sender signal, the engine control unit transmits a signal to the fuel pump control unit J538, which then regulates the fuel pump as required. Effects of signal failure If the fuel pressure sender fails, there is no longer fuel pressure control. The fuel pressure is held constant at 5bar.S360_376Oil level and oil temperature sender G266This sender is screwed into the bottom of the oil sump. The signal is used by several control units. The control unit with display in dash panel insert J285 uses this signal to increase the service interval. Signal use The engine control unit receives the signal via the powertrain CAN data bus and uses the oil temperature signal to control the late adjustment of the exhaust camshaft at high oil temperatures.Effects of signal failure The control unit uses the signal from the coolant temperature sender instead.S360_15649 Engine ManagementLambda probes G39 and G108A broadband Lambda probe has been placed in front of each starter catalytic converter. The broadband Lambda probes can determine the oxygen concentration in a wide range and thus establish the air/fuel ratio in the combustion chamber. Both Lambda probes are heated so that the operating temperature is reached faster. Signal use The Lambda probe signals are one input for calculating the injection time. Effects of signal failure There is no Lambda control if the pre-catalytic converter probe fails. No adjustment is made. A map is used for a limp-home mode.Broadband Lambda probeS360_222Lambda probes G130 and G131The planar Lambda probes come after the starter catalytic converter. They measure the residual oxygen in the exhaust gas. The engine can evaluate the operation of the catalytic converter using the residual oxygen in the exhaust gas. Signal use The engine control unit uses the signals from the probes after the catalytic converter to check the catalytic converter function and the Lambda control circuit. Effects of signal failure There is no Lambda control if the pre-catalytic converter probe fails. The catalytic converter function cannot be checked.Planar Lambda probeS360_22450 ActuatorsInlet camshaft control valve 1 N205, exhaust camshaft control valve 1 N318The solenoid valves are integrated into the camshaft housing. They distribute the oil pressure according to the requirements of the engine control unit in relation to the adjustment direction and the adjustment travel on the camshaft adjuster. Both camshafts are infinitely adjustable: - Intake camshaft 52° crank angle - Exhaust camshaft 42° crank angle - Maximum valve overlap angle 47° Crank angle When no oil pressure is available (engine stationary), the exhaust camshaft is mechanically locked.N205 N318S360_358Effects of signal failure If an electrical cable to the camshaft adjusters is defective or a camshaft adjuster fails due to mechanical failure or insufficient oil pressure, no further camshaft adjustment is performed.51 Engine ManagementElectric fuel pump G6The electrical fuel pump and the fuel filter are combined in the fuel supply unit. The fuel supply unit is in the fuel tank.Fuel filterTask The electronic fuel pump delivers the fuel in the lowpressure fuel system to the high-pressure fuel pump. It is actuated with a PWM signal by the fuel pump control unit. The electronic fuel pump always supplies the quantity of fuel required by the engine at the correct moment in time.Fuel pumpS360_190Effects upon failure If the electronic fuel pump fails, the engine will no longer run.Fuel pressure regulating valve N276The fuel pressure regulating valve is located on the bottom of the high-pressure fuel pump. The engine control unit regulates the high-pressure fuel between 35 and 100 bar using the regulating valve.Effects upon failure The engine control unit switches to limp-home mode.High-pressure fuel pump N276S334_35052 Ignition coils 1-6 with output stage N70, 127, 291, 292, 323, 324The ignition coil and output stage are one component. The ignition angle is controlled individually for each cylinder. Effects upon failure If an ignition coil fails, the injection for the corresponding cylinder will be deactivated. This is possible with a maximum of two cylinders.S360_192 Ignition coilsThe activated charcoal filter system solenoid valve N80is on the rear side (belt drive) of the engine and is controlled by the engine control unit. The fuel vapours collected in the activated charcoal filter are transported for combustion thus emptying the activated charcoal filter. Effects of signal failure If the power supply is interrupted, the valve remains closed. The tank is not ventilated.N80S360_19153 Engine ManagementInjectors cylinders 1-6 N30, N31, N32, N33, N83, N84The high-pressure injectors are fitted in the cylinder head. They are actuated by the engine control unit according to the firing order. After actuation, they inject fuel straight into the cylinder. The fuel is injected on one side due to the design of the engine. The injectors are therefore longer on cylinder banks 1, 3 and 5 than the injectors on cylinder bank 2, 4 and 6.S360_137Effects upon failure A faulty injector is detected by the fault recognition system and is no longer operated.The throttle valve drive for electric throttle G186is an electric motor that operates the throttle valve via gears. The adjustment range is continuous from the idle to the full load setting. Effects upon failure If the throttle valve drive fails, the throttle valve will move automatically to the limp-home mode position. An entry is made in the fault memory and the electronic power control fault lamp illuminates. Only limp-home mode features are available to the driver. The convenience functions are switched off.S360_195 Throttle valve Throttle valve housing G18654 Intake manifold flap valve N316Only the 3.2l V6 FSI engine and the 3.6l V6 R36 FSI engine have a variable intake manifold and therefore an electrical switching valve to connect or disconnect the vacuum control element for the switching mechanism to or from the vacuum system and thus perform the switching operation. Effects upon failure If the valve fails, the intake manifold flaps are moved to limp-home mode position by a mechanical spring. It corresponds with the power position of the intake manifold.S360_374 N316The circulation pump V55is controlled by the engine control unit. It supports the mechanical coolant pump when the engine is running. Once you have parked the vehicle and when there is no air flow, it is switched on depending on the coolant temperature and thus prevents heat accumulation in the engine. Effects upon failure If the recirculation pump fails, the engine may overheat.V55S360_19455 Engine ManagementLambda probe heaters Z19, Z28, Z29 and Z30The Lambda probe heaters have the task of quickly heating the ceramic part of the probes to an operating temperature of approx. 900°C when the engine is started and at low temperatures. The Lambda probe heater is controlled by the engine control unit. Effects upon failure The engine can no longer be controlled for emissions.S360_193 Lambda probe heater56 Control units in the CAN data busThe schematic shown below shows the integration of the engine control unit J623 into the vehicle CAN data bus structure. Information is transmitted between the control units via the CAN data bus.J743 J217 J104 J623 S360_175J533 J285 J519 J234 Legend J623 Engine control unit J104 ABS control unit J217 Automatic gearbox control unit J234 Airbag control unit J285 Control unit with display in dash panel insert J519 Onboard supply control unit J527 Steering column electronics control unit J533 Data bus diagnostic interface J743 Mechatronic unit for direct shift gearbox Colour coding Powertrain CAN data bus Convenience CAN data bus Infotainment CAN data bus J52757 Functional DiagramJ519K30 K15S360_165G39G130J160J271J670Z19Z29J623N70N127N291N292N323N324V55 N30 N31G39 Lambda probe G130 Lambda probe after catalytic converter J160 J271 J519 J623 J670 N30 N31 N70 Circulation pump relay Motronic current supply relay Onboard supply control unit Engine control unit Motronic current supply relay 2 Injector, cylinder 1 Injector, cylinder 2 Ignition coil 1 with output stageN127 N291 N292 N323 N324 Z19 Z29Ignition coil 2 with output stage Ignition coil 3 with output stage Ignition coil 4 with output stage Ignition coil 5 with output stage Ignition coil 6 with output stage Lambda probe heater Lambda probe 1 heater after catalytic converter58 J519S360_166G G6F1G266 CANJ285 J538 F N276G1G5G21J623G28G61G66G79G185 G186 G187 G188J338F F1 G G1 G5 G6 G21 G28 G61 G66 G79 G185 G186Brake light switch Oil pressure switch Fuel gauge sender Fuel gauge Rev. counter Fuel system pressurisation pump Speedometer Engine speed sender Knock sensor 1 Knock sensor 2 Accelerator position sender Accelerator position sender 2 Throttle valve drive for electric throttleThrottle valve drive angle sender 1 for electric throttle G188 Throttle valve drive angle sender 2 for electric throttle G266 Oil level and oil temperature sender G187 J285 J338 J538 J623 Control unit with display in dash panel insert Throttle valve module Fuel pump control unit Engine control unitN276 Fuel pressure regulating valve59 Functional DiagramJ519G108G131Z28Z30N205N80N318V7J293V177J623S360_167G410 N32 N33 N83 N84G163G83G40G247Hall sender Radiator outlet coolant temperature sender Lambda probe 2 Lambda probe 2 after catalytic converter G163 Hall sender 2 G247 Fuel pressure sender G410 Fuel pressure sender for low pressure G40 G83 G108 G131 J293 J519 J623 Radiator fan control unit Onboard supply control unit Engine control unitN32 N33 N80 N83 N84 N205 N318 V7 V177Injector, cylinder 3 Injector, cylinder 4 Active charcoal filter system solenoid valve Injector, cylinder 5 Injector, cylinder 6 Inlet camshaft control valve 1 Exhaust camshaft control valve 1 Radiator fan Radiator fan 260 J519 J533 K30 K15CANInput signal Output signal Positive Earth CAN data busG42G70J623S360_168G62J527G62 G42 G70 J519 J527 J533 J623Coolant temperature sender Intake air temperature sender Air mass meter Onboard supply control unit Steering column electronics control unit Data bus diagnostic interface Engine control unitZ28 Z30Lambda probe 2 heater Lambda probe 2 heater after catalytic converterThis functional diagram shows the 3.6l FSI engine in the Passat as an example.61 ServiceSpecial toolsDesignation T 10333 Funnel Tool Application The funnel T 10333 is used to fit the pistons.S360_189 T 10055 Puller T 10055/3 Adapter The puller T10055 with the adapter T 10055/3 is used to remove the oil pump.S360_184 T 10133 Tool set for FSI engines T 10133/10 Puller The tool set T 10133 with puller T 10133/10 is needed to remove the injectors.S360_186S360_187T 10332 Setting toolThe setting tool T 10332 is needed to lock the sprocket on the high-pressure fuel pump drive.S360_18862 Test YourselfWhich answers are correct? One or several of the answers could be correct. 1. By how many degrees has the V-angle of the 3.2l and 3.6l FSI engines changed compared with the VR6 multi-point injection? a) 3.4° b) 4.4° c) 4.6°2.Which statement about the pistons is correct? a) The pistons have a graphite abradable coating. b) The pistons in cylinder bank 1 and 2 differ in the arrangement of the recesses. c) The injected fuel is swirled due to the position and shape of the piston recess.3.What is the advantage of the large maximum adjustment travel of the camshafts? Which statement is correct? a) There is no external exhaust gas recirculation. b) The exhaust gas recirculation is internal. c) There is no exhaust gas recirculation is some cases.4.What intake manifold length achieves a high engine torque? a) A long intake manifold. b) A short intake manifold. c) The intake manifold length does not have an influence on the engine torque.63 Test Yourself5. Please fill in the missing terms.Engine speed sender G28a)b)Clutch position sender G476 Throttle valve module J338 with throttle valve drive angle sender 1 for electric throttle G187 Throttle valve drive angle sender 2 for electric throttle G188o)c)d) e)Brake light switch Ff) g)Oil level and oil temperature sender G266h) i)S360_15464 k)Injectors for cylinders 1-6 N30, N31, N32, N33, N83, N84Ignition coils 1 -6 with output stage N70, N127, N291, N292, N323, N324Throttle valve module J338 with throttle valve drive for electric throttle G186l)m)n)Inlet camshaft control valve 1 N205 Exhaust camshaft control valve 1 N318 Lambda probe heater Z19 Lambda probe 2 heater Z28 Lambda probe 1 heater after catalytic converter Z29 Lambda probe 2 heater after catalytic converter Z30o) p) Circulation pump relay J160 Circulation pump V55S360_15565 Test Yourself6 Which statement about the adjustment of the valve timing is correct? a) The high-pressure fuel pump drive sprocket needs to be locked. b) Setting the valve timing has not changed due to the high-pressure fuel pump drive. c) There is a special tool for locking the drive sprocket on the high-pressure fuel pump.7.Please fill in the missing terms. a) b) c)S360_402h) d) e) f) k) l) m) i)g)66 8.What can be checked through the oil pump service access? a) The chain tension of the primary roller chain. b) The mechanical wear of the oil pump. c) The condition of the pressure relief valve without the chain drive being removed.9.What work requires the special tool T 10332?Answer:S360_18867 Test Yourself68 69Answers 1. b); 2. a),b),c); 3 a), b); 4 a); 5. a) Air mass meter G70, b) Accelerator position sender G79 and accelerator position sender 2 G185, c) Hall sender G40 and Hall sender 2 G163, d) Coolant temperature sender G62 and radiator outlet coolant temperature sender G83, e) Knock sensor 1 G61 and knock sensor 2 G66, f) Fuel pressure sender G247, g) Fuel pressure sender for low pressure G410, h) Lambda probe G39 and Lambda probe 2 G108, i) Lambda probe after catalytic converter G130 and Lambda probe 2 after catalytic converter G131, k) Fuel pump control unit J538 and fuel system pressurisation pump G6, l) Fuel pressure regulating valve N276, m) Activated charcoal filter solenoid valve 1 N80, n) Intake manifold flap valve N316, o) Radiator fan control unit J283 and radiator fan V7, p) Radiator fan 2 V177; 6. a), c); 7. a) High-pressure fuel pump, b) Fuel pressure sender for low pressure G410, c) Cylinder bank 1 fuel rail, d) Pressure retention valve, e) Fuel system pressurisation pump G6, f) Pressure limiting valve, g) Fuel filter, h) Fuel pressure sender G247, i) Cylinder bank 2 fuel rail, k) Fuel pressure regulating valve N276, l) Engine control unit J623, m) Fuel pump control unit J358 8.) c), 9.) The setting tool T 10332 is needed to lock the sprocket on the high-pressure fuel pump drive. Notes70 71 360© VOLKSWAGEN AG, Wolfsburg All rights and rights to make technical alterations reserved. 00.2811.89.20 Technical status 05.2007 Volkswagen AG Service Training VSQ-1 Brieffach 1995 38436 Wolfsburg❀ This paper was manufactured from pulp that was bleached without the use of chlorine.