TECHNICAL DOCUMENTATION

SSP 319 The Golf 2004 Electrical system

PDFEN60 pages3 MB
SSP 319 The Golf 2004 Electrical system - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingSelf-study programme 319The Golf 2004 Electrical systemDesign and function The most striking change compared with the previous model is the rear lighting of the Golf 2004. The one-piece light unit, common on the previous model, has now been replaced by a two-piece light unit. This is comprised of a separate independent light element in the side part and a fixed element in the tailgate. In this way, the car's relationship to the prestige Volkswagen models is made evident. A bright and high quality appearance is achieved by day and by night by means of round elements, comprised of several parts, located behind clear lenses.S319_063NEWImportant NoteThis self-study programme shows the design and function of new developments! The contents will not be updated.For the latest testing, setting and repair instructions, please refer to the relevant workshop literature.2 ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4LIN data bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Onboard power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Tyre pressure monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Convenience and safety electronics. . . . . . . . . . . . . . . . . . 42Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Test yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 563 IntroductionFuse boxes and relay slots in vehicle electrical systemFitting locations The onboard electrical system of the Golf 2004 is similar to that of the Touran. Golf 2004 and Touran vehicles are based on the same platform. The onboard electrical system of the Golf 2004 is of the decentral design. Distribution of the fuse boxes and relay sockets in various locations facilitates quick and precise fault diagnosis.Electrics box, on left in engine compartmentPre-fuse box, on left in engine compartment4 Relay carrier, on left beneath dash panel, above onboard power supply control unitRelay carrier of onboard power supply control unit on left under dash panelFuse box, on left in dash panelS319_0015 IntroductionThe networking conceptOverview of networked control units In order that data can be transferred without conflict or interference between the individual control units, these are connected together in a network via various data bus systems. The data bus diagnostic interface J533 (Gateway) provides an interface for the following data buses: Drivetrain CAN data bus Convenience CAN data bus Infotainment CAN data bus Dash panel insert CAN data bus Diagnosis CAN data busT16 J220 NOxJ431J285 J334 J533Drivetrain CAN data bus Convenience CAN data bus Infotainment CAN data bus LIN data bus CAN data bus Sensor Dash panel insert CAN data bus Diagnosis CAN data busS319_011CAN data bus wire Communications line LIN data bus wireJ503 R J345J608J412 J519 J525J255 J364J136R78J386J388In addition to the CAN data bus, a number of electric components are networked via the LIN data bus.J387J3896 G419Key D E221 G85 G273 G384 G397 G419 H8 J104 J136 J217 J220 J234 J255 J285 J334 J345 J364 J386 J387 J388 J389 J393 J400 J412 J431 J446 J500 J503 J519 J525 J527 J533 J587 J604 J608 J743* NOx R R78 T16 * Ignition/starter switch Operating unit in steering wheel Steering angle sender Interior monitoring sensor Vehicle inclination sender Rain and light detector sensor ESP sensor unit Anti-theft alarm system horn ABS with EDL control unit Seat and steering column adjustment control unit with memory Automatic gearbox control unit Motronic control unit Airbag control unit Climatronic control unit Control unit with display in dash panel insert Immobiliser control unit Trailer detection control unit Auxiliary heater control unit Driver door control unit Front passenger door control unit Rear left door control unit Rear right door control unit Convenience system central control unit Wiper motor control unit Mobile telephone operating electronics control unit Headlight range control, control unit Parking aid control unit Power steering control unit Control unit with display for radio and navigation Onboard supply control unit Digital sound package control unit Steering column electronics control unit Data bus diagnostic interface Selector lever sensors control unit Auxiliary air heater control unit Special vehicle control unit Direct shift gearbox mechatronics NOx sensor Radio TV tuner 16-pin connector, diagnosis interface On direct shift gearboxes onlyJ743*J217J104J587J500J234G85E221 D J527 J446J400 G397J604J393G273H8G384S319_0087 IntroductionControl units in drivetrain CAN data busControl units and fitting locations The adjacent illustration shows the control units of the drivetrain CAN data bus and associated fitting locations. The data is transferred at a rate of 500 kbit/s. Transfer is made via the orange/black CAN high wire and orange/brown CAN low wire. To guarantee data transfer without conflict or interference, the CAN wires are twisted together.Airbag control unit J234, beneath centre console, on front of tunnelABS with EDL control unit J104, on right of bulkhead in engine compartmentMotronic control unit J220, under plenum chamber cover8 Headlight range control, control unit J431, on right of glove compartmentSteering column electronics control unit J527, beneath steering column switchData bus diagnostic interface J533, beneath dash panel, above accelerator pedalAutomatic gearbox control unit J217, on left in wheel housingS319_0029 IntroductionThe control units in the drivetrain CAN data busControl units and fitting locations The adjacent illustration shows the control units of the convenience CAN data bus and associated fitting locations. The speed of data transfer is 100 kbit/s. The data is transferred via the orange/green CAN high wire and orange/brown CAN low wire. To guarantee data transfer without conflict or interference, the CAN wires are twisted together.Steering column electronics control unit J527, on steering column switchConvenience system central control unit J393, on right beneath dash panel, behind glove compartmentClimatronic control unit J255, in centre console10 Parking aid control unit J446, in rear right side panelTrailer detection control unit J345, in rear right side panelOnboard supply control unit J519, under dash panel on relay carrierDoor control units J386, J387, J388, J389, installed in doorsData bus diagnostic interface J533, beneath dash panel, above accelerator pedalS319_00411 IntroductionThe control units in the infotainment CAN data busControl units and fitting locations The adjacent illustration shows the control units of the infotainment CAN data bus and associated fitting locations. The infotainment CAN data bus transfers data at a rate of 100 kbit/s. The CAN high wire is orange/purple and the CAN low wire is orange/brown. To guarantee data transfer, the CAN wires are twisted together.Mobile telephone operating electronics control unit J412, under right seat, beneath carpet covering on right sill panelAuxiliary heater control unit J364, on front right beneath wing12 Control unit with display for radio and navigation J503 or Radio R, in centre consoleCD changer R41, in centre console, beneath front armrestS319_00513 IntroductionThe control units in the dash panel insert CAN data bus and in the diagnosis CAN data busDash panel insert CAN data bus Information is exchanged via the dash panel insert CAN data bus between the dash panel insert control unit and the data bus diagnostic interface. These are the only control units in this data bus system.Diagnosis CAN data bus The transfer of data between the diagnosis tester VAS 5051/5052 and the data bus diagnostic interface is via the diagnosis CAN data bus.Rate of data transfer The rate at which data is transferred is 500 kbit/s for both CAN data buses.Dash panel insert control unit J28514 Data bus diagnostic interface J533, beneath dash panel, above accelerator pedal16-pin connector, diagnosis interface T16, on left beneath dash panelS319_00615 LIN data busThe LIN data bus as sub data bus systemLocal Interconnect Network (LIN) defines a local system in which all associated components within a specific area are located.●●● ●The local sub-system is a cost effective version of CAN data bus. The defined consumer interface makes simple exchange of the connectors possible. Bus connection in crash area Bus connection in critical safety areasInformation is exchanged in the LIN data bus system via a master control unit and up to 16 slave control units. Communication is initiated only by the master. Slave control units cannot communicate independently. Several independent LIN data buses can be installed in the vehicle with different functions. Information is exchanged between the individual bus systems via the master control units connected to the CAN data bus.The LIN bus systemJ400 G397G273G384H8J527E221J393J519Key E221 G273 G384 G397 H8 Operating unit in steering wheel Interior monitoring sensor Vehicle inclination sender Rain and light detector sensor Anti-theft alarm system horn J393 J400 J519 J527S319_007Convenience system central control unit Wiper motor control unit Onboard power supply control unit Steering column electronics control unit16 Master control unit The control unit connected to the CAN data bus takes on the master functions of the LIN data bus system. Tasks●Slave control unit In the LIN data bus system, individual control units, sensors or actuators can act as slave control units. The electronics integrated in the control units evaluate the information, convert it into digital information and send it, once the request has been made, via the LIN data bus to the master control unit. Actuators are assigned their tasks by a signal, which comes from the master control unit via the LIN data bus. Following interrogation of the master control unit, the electronics integrated in the sensors send the actual status to the master control unit, in which a target/reference comparison is carried out.●● ●Conversion of local data bus messages to data format of CAN data bus Monitoring of data bus conversion and rate of data transfer Control of data transfer cycle Transfer of diagnosis data from slave control unitsThe convenience system central control unit, illustrated, shows the wiring of the LIN and CAN data buses.LIN data bus wiresCAN data bus wiresS319_06817 Onboard power supplyThe electrics boxHoused in the electrics box are the fuses for components of the engine compartment and the interior. The connection between electrics box and battery is very short (approx. 500 mm), which enables use of the battery as a high frequency filter between the consumers mounted directly on the box. Due to the increased number of fuses, the rating of the fuses can be set to the individual consumers. Fitting location The electrics box can be found on the left in the engine compartment.Electrics boxS319_03118 The electrics box and pre-fuse box are located in a housing in the engine compartment.Electrics box In addition to the fuses, the following relays can also be found in the electrics box:● ● ● ●Terminal 15 voltage supply relay J329 Terminal 30 voltage supply relay J317 Terminal 50 voltage supply relay J682 Fuel pump relay J17 (not diesel and FSI)S319_009Pre-fuse box In the pre-fuse box are fuses for:● ● ● ● ● ● ●the alternator the electromechanical power steering the radiator fan power supply from terminal X the auxiliary heater terminal 30 the rear battery (V6) (to be introduced at a later stage)S319_01019 Onboard power supplyThe relay carrierFitting location On the left under the dash panel is a relay carrier and the onboard supply control unit.Relay carrier Additional relays may be included on the relay carrier depending on the equipment level. On vehicles with electric seat adjustment, the automatic safety device (thermal safety) is installed here.S319_012Relay carrier on onboard supply control unit The following relays can be found on the onboard supply control unit relay carrier:● ●● ● ● ● ●Power supply relay terminal 30G Terminal 15 voltage supply relay (on V6 only) Terminal 75 voltage supply relay Heated rear window relay J9 Horn relay J413 Double washer pump relay 1 J729 (right) Double washer pump relay 2 J730 (left)S319_06520 The fuse boxFitting location The fuse box can be found on the left of the dash panel behind a cover.Fuses Included in the fuse box are fuses for the electrical components in the vehicle.S319_013Please refer to the electronic service information system (ELSA) for current assignment details of the fuse box.21 Onboard power supplyThe data bus diagnostic interface J533Due to the vast range of functions in the vehicle, large amounts of data must be transferred. To guarantee optimal exchange of data, several data bus systems are required. The function previously integrated in the dash panel insert or onboard supply control unit is now assumed by the separate data bus diagnostic interface (Gateway). It forms the interface for data bus systems that are independent of each other and allows information to be exchanged without conflict or interference.Fitting location The data bus diagnostic interface is installed beneath the dash panel, above the accelerator pedal.Master functions The data bus diagnostic interface takes on the master functions of terminal 15 run-on and sleep and wake-up modes.Further information can be found in SSP 307 "The Touran - Electrical system".S319_01422 Transport mode For transportation of the vehicles to the dealerships, power consumption should be kept to a minimum to protect the battery from possible discharge. To do this, the following systems are isolated when transport mode is activated:● ● ● ● ● ● ●Transport mode can only be selected during the first 150 km. The data bus diagnostic interface then switches transport mode off, after which point it is no longer possible to activate it.Radio Radio remote control Interior monitoring Auxiliary heater telestart receiver Inclination sensor Save LED in door 30 second interior light switch-off delayThe transport mode can only be switched on and off using diagnosis tester VAS 5051 via the vehicle self-diagnosis function [collective services].S319_030"Tra" is shown, when transport mode is active, in the odometer display of the dash panel insert.S319_02923 Onboard power supplyThe onboard supply control unit J519Fitting location The onboard supply control unit can be found on the left underneath the dash panel where it forms a unit with the relay carrier.S319_065Versions The onboard supply control unit is available in two versions.●Onboard supply control unitHigh version for vehicles with fog lights and/or bi-xenon lights and personalisation Medium version for all other vehicles●Fog lights can only be retrofitted if the medium version of the onboard supply control unit is upgraded to the high version.Relay carrier on onboard supply control unitS307_01724 Tasks The onboard supply control unit actuates and controls the following functions: - Exterior light control with bulb monitoring In the event of bulb failure, the relevant warning lamp will ligh up or a text message is displayed in the dash panel insert. - Convenience light: Coming home Leaving home Dimmable instrument backlights - Coulisse lighting - Windscreen wipers Conveyance of CAN data bus signals from onboard power supply control unit to wiper motor control unit - Rear window wiper When reverse gear is selected, the rear window wiper is activated. - Windscreen and rear window washer pump - Turn signal control - Electric load management Shut-off below 11.8 V, as in TouranThe onboard supply control unit also controls the following functions: - Interior light control Terminal 30G, via which voltage is supplied to the interior lights, is activated by the onboard supply control unit. - Heated rear window When the heated rear window button is actuated, the rear window is activated via the onboard supply control unit. - Terminal actuation The onboard power supply control unit controls terminal 75x via an X contact relief relay. Terminal 15 is actuated via terminal 15 voltage supply relay in the electrics box. Terminal 50 is actuated via terminal 50 voltage supply relay in the electrics box. - Fuel pump readiness When the driver's door is opened, the electric fuel pump is supplied with power by the onboard supply control unit. After the engine has started, power is supplied from the Motronic control unit.For further information, please refer to SSP 307 "The Touran - Electrical system".25 Onboard power supplyThe exterior light controlMain headlights The twin headlights with dipped and main beam reflectors are equipped with H7 bulbs on the medium version. To improve visibility for other road users, the turn signals are located linearly beneath the dipped and main beam lights, i.e. a well balanced distribution of light can be observed from the turn signal. On the high version, a combination of the bi-xenon module and a main beam reflector equipped with H7 bulbs is available as an option. The equipment is supplemented with a washer system and dynamic headlight range control.S319_035Side light Main beam headlights Turn signal light Dipped beam headlightsBulb renewal with One-Touch-System Thanks to the spacious layout of the headlight design and the One-Touch-System, the cover and the H7 bulbs can be removed by a simple twist motion and replaced with the help of a guide.For further information, please refer to SSP 307 "The Touran - Electrical system".S319_03426 Tail lights Installed for the first time in the Golf 2004 are the split rear lights with round elements, which are comprised of several elements. The light unit integrated in the side panel is responsible for the tail, brake and turn signal light functions. Installed in the tailgate is a fog light on the left and a reverse light on the right. The auxiliary brake light in the roof spoiler and turn signals mounted in the exterior mirrors complement the headlight and rear light functions and provide an additional visual aid for other road users.Tail light Tail and brake lights Rear fog lightS319_056Turn signal lightActuation of the light functions The rotary light switch is a powerless semi-conductor module, which sends information about the switch position, in the way of signals, to the onboard supply control unit. The onboard supply control unit controls all of the relevant exterior light functions. Advantages●● ●Voltage peaks in the light switch are avoided to increase longevity of the bulbs Special functions: The bulb monitoring system can be displayed visibly in the dash panel insert27 Onboard power supplyThe convenience lightingComing home When occupants alight from the vehicle and close the doors, including the tailgate, the vehicle surround lighting is activated for a short period. If the rotary light switch is in the dipped beam position, the lights are switched off completely once the lighting period has elapsed. If the rotary light switch is in the side light position, the side light bulbs remain on after the surround lighting is switched off.Leaving home After the vehicle has been unlocked using the radio remote control, the area around the vehicle is lit up for a brief period.After the lighting period has elapsed or in the event of an interruption, the coming home function cannot be reactivated until the ignition is switched on.28 The following lights are switched on by the coming home and leaving home function:● ● ● ●Front side lights Dipped beam headlights Tail lights Number plate lightS319_070Side lightDipped beam headlightsActivation or deactivation of the coming home and leaving home function and the lighting period are set in the dash panel insert via the "Light and Vision" personalisation menu, or with the diagnosis tester VAS 5051/5052.S319_003Tail light29 Onboard power supplyThe windscreen wiper systemWiper actuation The wiper system comprises of a single motor with mechanical connection between the wiper arms. The switch positions of wiper switch E are sent directly to the steering column electronics control unit J527 and then via the convenience CAN data bus to the onboard supply control unit J519. The onboard supply control unit passes on information about the selected wiper stage via the LIN data bus to the wiper motor control unit J400, which is responsible for control of the wiper action. On vehicles with rain and light detector sensor, the wiper frequency is calculated in rain sensor mode and sent to the wiper motor control unit. In intermittent operation, the wiper intermittent stages are speed dependent and vary between 2 and 24 seconds. The wiper control system detects a blockage in the wiper motion and reacts according to the degree of resistance. The wipers will try to move the obstacle out of the way. If it has still not been moved after the fifth attempt, the wiper will stay in this position. Activation of the wiper after the obstacle has been removed is possible only by actuation of the windscreen wiper switch again.Instead of a 360 degree rotation, the drive housing of the wiper performs a reversing action through an angle of 150 degrees. In this way, the amount of space required for the wiper linkage has been reduced.S319_06930 Overview of wiper systemJ104G397J400F266DEJ519 J527 J533S319_016Key D E F266 G397 J104 Ignition/starter switch Windscreen wiper switch Bonnet contact switch Rain and light detector sensor ABS with EDL control unit J400 J519 J527 J533 Wiper motor control unit Onboard supply control unit Steering column electronics control unit Data bus diagnostic interface31 Onboard power supplyService/winter position If, within 10 seconds of switching off the ignition, the windscreen wiper switch is switched to the tip wiping position, the wipers will move to the upper end position of the wiped arc. When the wiper arms are in the service/winter position, the wiper blades can be renewed without restriction or the wiper arms can be lifted up to prevent the blade rubber from freezing to the windscreen. The wipers will revert to the rest position as soon as the windscreen wiper switch is actuated twice with the ignition switched on or at a driving speed of 2 km/h.S319_015When the vehicle is stationary and the bonnet is in the open position, the wipers cannot be activated.The headlight washer systemActuation of the headlight washer system is carried out by the onboard supply control unit and is part of the "wash/wipe" function.Activation conditions - Ignition on - Side, dipped or assistant driving lights ON - Steering column switch in "wash/wipe" positionWash cycle - Every fourth time the "wash/wipe" function is actuated32 The quick lock systemEasy removal/assembly Improved longevity Improved anti-crimp and frost protection Corrugated-type tubesIncluded in the new features of the new Golf 2004 is also the quick lock system for the windscreen washer system. With this system, the windscreen washer hoses are replaced with corrugated-type tubes, which avoids the risk of crimping. The connections to the windscreen washer pump and the washer jets are fixed by means of securing clips.EngagedS319_049Securing clipWasher jetTo release the connecting pieces, the securing clip must be pressed outwards by hand so that the hose can be removed. For assembly, the hose is pressed onto the connecting piece and the securing clip engages automatically.DisengagedS319_066Securing clipWasher jet33 Onboard power supplyControl unit with display in dash panel insert J285The control unit with display in the dash panel insert receives its information via the data bus diagnostic interface J533 and the dash panel insert CAN data bus. Further external sensor signals are sent to the dash panel insert via separate wiring:● ● ●Diagnosis Diagnosis of the control unit with display in the dash panel insert is carried out using the diagnosis tester VAS 5051/5052 via the CAN data bus. Furthermore, the dash panel insert control unit is capable of self-monitoring. If a fault occurs, this will be shown in the display by the letters "def".● ●● ●F1 Oil pressure switch F34 Front left brake pad wear warning contact G17Ambient temperature sender, located in bumper G32Coolant shortage indicator sender G33Windscreen washer fluid level sender (optional) G34Front left brake pad wear sender J538Fuel pump control unitVersions The sections in the display vary depending on the three versions of dash panel insert:● ● ●Lowline version Midline version Highline version For further information, please refer to SSP 307 "The Touran - Electrical system".LED warning lamps only appear in the upper area on Lowline and Midline versions.34 Immobiliser control unit J362Immobiliser IV The immobiliser control unit J362 is integrated in the dash panel insert control unit. With the ignition switched on, it enables or disables vehicle-specific functions. The control unit can only be adapted using the "guided fault finding" function in the diagnosis tester VAS 5051. Adaption channels and fault memories are dealt with separately. The immobiliser requires its own address word 25 for diagnosis.Active immobiliser If the immobiliser is active, a short audible signal will sound and the immobiliser warning lamp will light up in the rev counter.The illustration shows a dash panel insert of the Highline versionS319_051Diagnosis of the immobiliser control unit is done via the guided fault finding function.35 Onboard power supplyThe warning lamps in the dash panel insertS319_017The dash panel insert of the diesel engine Symbol Control lampAirbagLowlineXMidlineXHighlineXWarning message or warningAirbag fault! Airbag Belt tensioner deactivated! ABSAnti-lock braking system (ABS) Brake pad wear indicator (BWI) Low brake fluid levelXXXXXPictogramCheck brake lining! 1 x audible warning Stop Brake fluid Operating instructions! 3 x audible warningsFlashingFlashingFlashingPreglow period (diesel engines)XXX*Electronic Power Control (EPC) Dynamic oil pressure warningXXXFlashingFlashingFlashing Pictogram XStop Oil pressure Engine OFF! See operating instruction 3 x audible warnings Low priority fault yellow High priority fault red 3 x audible warnings*Electronic power steering (EPS) Electronic brake pressure distribution (EBD) Parking brake systemXXFlashingFlashingFlashingXXXHandbrake applied! 1 x audible warning*Electronic stabilisation program (ESP), traction control system (TCS)XXX36 SymbolWarning lampLeft turn signalLowlinexMidlinexHighlinexWarning message or warningAcoustic checkRight turn signalXXXAcoustic checkMain beam headlightsXXXCruise control system (CCS)XXXBulb blown / driving light defective Tailgate / door openXXXe.g. front right dipped beam light defective! e.g. Tailgate open 1 x audible warning Replenish fuel! 1 x audible warning Stop - Check coolant! Operating instructions! 3 x audible warningsXXPictogramFuel reserveXXPictogramLow coolant level / excessive coolant temperature Alternator charge controlFlashingFlashingFlashing Pictogram XXXEngine check Onboard diagnosis (OBD) Bonnet openXXXEngine fault Workshop! Exhaust gas Workshop! Door warning! Bonnet! 1 x audible warning if v 6 km/hXXPictogramRear fog lightXXXTOG / oil levelXXPictogramCheck oil level! Oil sensor Workshop! 1 x audible warning 1 x audible warningTyre pressure monitorXXXShift lockXXXSeat beltXXXPlease apply seatbelt! Belt warning alarm**Tank flap openXXPictogramLow washer fluidXXPictogramReplenish washer fluid! 1 x audible warning Immobiliser active! 1 x audible warningImmobiliserFlashingFlashingFlashing*) Symbols marked with an asterisk are new or have been revised. **) Planned as of week 22 / 2004 37 Onboard power supplyThe convenience system central control unit J393Fitting location The convenience system central control unit can be found beneath the dash panel, on the right behind the glove compartment. Tasks● ● ● ● ●Control of central locking function Actuation of rear doors Actuation of tank flap release Actuation of tailgate lock release Actuation of anti-theft alarm system via LIN data busS319_064The mirrors were controlled until now via the convenience system central control unit. The door control units now control all systems in the area of the doors, which reduces the amount of wiring.The convenience system central control unit is the master control unit in the LIN data bus, via which data transfer for the anti-theft alarm system is carried out. Included in the anti-theft alarm system are interior monitoring sensors, intelligent sirens and the vehicle inclination sensor.Depending on the version, some of the sockets may not be occupied in the convenience system central control unit.38 Trailer detection control unit J345Fitting location The trailer detection control unit can be found on the left behind the luggage compartment trim in the side panel. Task The trailer detection control unit has the task of detecting whether a trailer is connected, it controls the trailer lights and also checks the function of the lights. The bulb current of each bulb wiring circuit is checked. There is an exception in the fog light and tail lights, as these are not available on every trailer. Control of the trailer lighting is provided by the onboard supply control unit, which communicates with the trailer detection control unit via the CAN data bus. In the Golf 2004 there is no warning lamp in the dash panel insert control unit J285 for trailer detection.S319_024Retrofitting of the trailer detection control unit is possible. However, problems may arise due to the fact that connection to the CAN data bus is necessary.Installation of aftermarket control units, which have not been authorised by Volkswagen, is not recommended. In most cases, these are connected to the tail lights, which can result in faulty operation of the bulb monitoring system. In addition, the same tail light of the Golf 2004 is actuated, depending on the function, in varying degrees of brightness.Please refer to the electronic service information system (ELSA) for the latest pin/terminal assignment and coding of the trailer detection control unit.39 Tyre pressure monitorThe tyre pressure monitoring systemThe tyre pressure monitoring system is a software module in the ABS control unit, which detects slow and gradual loss of air from the tyres. From current ABS and ESP data (wheel speed, current vehicle status), it filters out fine changes and compares the information with reference data. The circumference of a tyre can change depending on the amount of air inside. If the circumference changes beyond a specified degree, the tyre pressure monitoring system will detect pressure loss. If pressure loss is detected, the driver will be shown a permanent warning by the tyre pressure monitor warning lamp in the speedometer of the dash panel insert and one audible warning will sound when the ignition is switched on. The warning will not be reset until the driver starts a new calibration procedure.System overview Tyre pressure monitor warning lampJ285 Tyre pressure warning buzzerJ533J104 Tyre pressure monitor display buttonABS wheel sensors KeyS319_018J104 ABS with EDL control unit J285 Control unit with display in dash panel insert J533 Data bus diagnostic interface●Evaluation of data is interrupted during fast cornering, on uneven road surfaces, during braking and when the vehicle is driven up or down steep gradients. In these situations, tyre pressure loss cannot be detected. Each time the tyre pressure is altered or if a tyre has been changed, the driver must carry out a calibration procedure to prevent false warnings that may occur from old reference data. Even in the event of repair work on the running gear, the calibration procedure should be carried out by the workshop and the driver informed of this fact.●40 Calibration Since the tyre characteristics can change, a calibration procedure must be performed each time the tyre pressure is altered, or when a wheel is changed, to allow new reference data to be calculated.Calibration procedure To start the calibration procedure, the tyre pressure monitor display button must be pressed for 2 seconds. The warning lamp in the speedometer will light up while the button is pressed and will go out after 2 seconds. In addition, a confirmation signal will sound. As the vehicle is driven normally, the system will calibrate itself to the set tyre pressures and type of tyres. Tyre pressure monitoring will gradually take over as the calibration procedure nears the end. It takes just a few minutes before basic monitoring can start, based on the figures analysed by the system.System fault In the event of a fault in the ABS with EDL control unit, tyre pressure monitoring will be stopped and the tyre pressure monitor warning lamp will light up in the speedometer.Diagnosis Diagnosis is carried out using the diagnosis tester VAS 5051/5052 via the guided fault finding function in the ABS with EDL control unit J104.41 Convenience and safety electronicsThe exterior mirrorsIn the Golf 2004, electrically folding exterior mirrors are available as an option. Operation of the mirrors is via a mirror setting switch in the driver's door. If the switch is turned to the "fold in" position, the exterior mirrors will fold in automatically. If the exterior mirrors are in the folded position, they can also be returned to the normal position above the speed threshold.S319_050Normal positionFolded positionS319_059S319_05842 New features and installation of the mobile telephoneFor the telephone system in the Golf 2004, a Nokia 6310i is offered as an option.R66 R54Equipment● ● ● ●● ●Nokia 6310i Telephone interface Telephone mounting Buttons for information and breakdown assistance Microphone installed in bulb module Dual band "shark-fin" roof aerial GSM 900/1800)Infoservice button Breakdown assistance buttonAdditional functions●●●● ●● ●Convenient operation via Highline dash panel insert (telephone book and call status display) Operation via multi-function display paddle on steering column switch Operation via multi-function steering wheel with permanently installed phone (optional) Hands-free/battery charger Voice output via radio/navigation loudspeaker Diagnosis via CAN data bus Programmable sleep timer (personalisation)J412J285 J527Mobile emergency call feature If the "Infoservice" or "Breakdown" assistance button is pressed during a normal telephone conversation, the current call will be cancelled and a connection will be made to the Volkswagen Service Call Centre for emergencies and information.E221S319_044Key E221 Operating unit in steering wheel J285 Control unit with display in dash panel insert J412 Mobile telephone operating electronics control unit J527 Steering column electronics control unit R54 Mobile telephone R66 Aerial for telephone/navigation/auxiliary heater43 Convenience and safety electronicsPersonalisationThe user based settings for different unit functions in the convenience and infotainment system are made via an operating unit and a display. Operation is via control levers on the steering column switch and selection is made from the menu via the display in the dash panel insert. The settings selected are stored in the control unit, which is responsible for the control of each function. Transfer of the necessary information between the control unit with display in the dash panel insert and the other associated control units is managed by the CAN data bus.J285 Steering column switchJ527J533J519J393J364S319_067Key J285 J364 J393 J519 J527 J533 Control unit with display in dash panel insert Auxiliary heater control unit Convenience system central control unit Onboard supply control unit Steering column electronics control unit Data bus diagnostic interface44 Example of menu guideLight & vision Coming home Leaving home Footwell lightConvenience signallingWipers Factory defaultConvenience signalling OFF ONOFF BackConvenience signalling ONON OFFBackConvenience signalling ONONConvenience signalling OFFON OFFOFFBackBackConvenience signalling OFFON OFFPress and release Press and holdBackS319_060For precise details on operation, please refer to the operating instructions.45 Convenience and safety electronicsThe radios in the Golf 2004Radio R 100 The R100 radio is available to key account holders, e.g. fleet operators. It is a radio system with the following functions: - Two loudspeaker channels (front only, each 20 W) - RDS FM/AM Europe Radio (AM without LW) - Without integrated disc drive - Controls for external 6 disc CD changer - Telephone control (hands-free operation) - Speed-dependent volume control (GALA) - Self-diagnosis inc. loudspeaker diagnosis - Transport mode (voltage minimisation for vehicle transportation and storage)S318_175Radio RCD 300 The RCD 300 radio is available to private customers as a standard radio system. It has the following functions: - Two or four loudspeaker channels (each 20 W) - RDS FM/AM Europe Radio (AM without LW) - Display of stored stations with RDS names - FM 2 diversity tuner - Operation via multi-function steering wheel and multi-function display - Integrated single CD drive - Controls for external 6 disc CD changer - Telephone control (hands-free operation) - GALA - Self-diagnosis inc. loudspeaker diagnosis - Transport modeS318_17746 Radio RCD 500 The top radio in the 2004 Golf is the RCD 500 with the following functions: Four loudspeaker channels (each 20 W) RDS FM/AM Europe Radio (AM without LW) Display of stored stations with RDS names FM 2 diversity tuner Operation via multi-function steering wheel and multi-function display Integrated 6 disc CD changer Controls for external 6 disc CD changer Telephone control (hands-free operation) GALA Traffic Information Memory (TIM) Model-specific sound adjustmentS318_179- Self-diagnosis inc. loudspeaker diagnosis - Transport mode - Optional external sound amplifier can be connected.MFD 2 radio navigation system A radio system with an integrated navigation system is also available for the Golf. It is operated in much the same way as the radio navigation system from the Touareg. Features include: Multi-colour display (MCD) Dynamic traffic route guidance Four loudspeaker channels (each 20 W) RDS FM/AM Europe Radio (AM without LW) Display of stored stations with RDS names External diversity tuner Operation via multi-function steering wheel and multi-function display Controls for external 6 disc CD changer Telephone control (hands-free operation) GALA TIM Self-diagnosis inc. loudspeaker diagnosisS318_287To remove and install a radio, the cover frame must be removed to gain access to the threaded connection at the rear.47 Convenience and safety electronicsThe aerialsIn the Golf 2004, various aerial systems are installed depending on the equipment level. No provision has been made to allow retrofitting of a rear window aerial.+ AM circuit -Radio R 100 The aerial system for the R 100 radio consists of a rear window aerial and a radio connection.FM circuit (+)FM circuit (-) Aerial amplifier (impedance transformer)S319_021Radio RCD 300/RCD 500 On the RCD 300 and RCD 500 radios there is an internal diversity tuner (automatic selection between aerials). An external diversity tuner is not required. Two rear window aerials are connected simultaneously to the radio. The radio automatically selects the aerial with the strongest signal.AM circuit+-FM circuit (+)FM circuit (-)Aerial amplifier (impedance transformer)S319_02248 MFD 2 radio navigation system The MFD 2 radio navigation system does not feature an internal diversity tuner. It has an external tuner, to which two rear window aerials are connected.AM circuit+-FM circuit (+) Aerial amplifier (impedance transformer)FM circuit (-)External diversity tuner Aerial signal (coax)Control line (coax)S319_023On the MFD 2 radio navigation system, a shark-fin type roof aerial is installed. For reasons of safety, a specified breakage point is integrated in the design (red line). If the aerial breaks off, there is a risk of water ingress.S319_032If a vehicle is ordered without radio system or without radio preparation, only the rear aerial structure is provided. No provision has been made for connection to this structure.49 Convenience and safety electronicsMulti-function steering wheelSystem overview Data is exchanged between the multi-function steering wheel and the steering column switch module via a LIN data bus. Communication of the signals from the steering column electronics control unit to the data bus diagnostic interface is done via the CAN data bus, from where these signals are then passed on to the relevant control units. The functions of the multi-function steering wheel become active as soon as the ignition is switched on.J527E221 J533J285R66J412J503 RR54 Key E221 Operating unit in steering wheel J285 Control unit with display in dash panel insert J412 Mobile telephone operating electronics control unit J503 Control unit with display for radio and navigation J527 Steering column electronics control unit J533 Data bus diagnostic interface R Radio R54 mobile cellular telephone R66 Aerial for telephone, navigation, auxiliary heater 15 30S319_01950 Multi-function buttons Button illumination is controlled by terminal 58d. There is only one symbol code, which communicates information from the button via the steering column switch module to the CAN data bus. For this reason, button functions can only be carried out individually. If no telephone is installed, the telephone buttons are non-functional. After several minutes, the system detects if a button is sticking and will disable the function until the button is released again. All other buttons remain functional.S319_025Button symbolDescription Switch to basic telephone menu, various sub functions, such as caller list, make connection Accept call, make call Mute selection of audio sourcesEnd call Switch (mode) between FM/ AM audio sources, CD-changer and CD (radio) Next track/start station searchPrevious track/start station search Volume up Volume down51 Convenience and safety electronicsHeadliner wiring with printed circuit wiresBy the use of printed circuit wires, an increase in headroom has been achieved. Routing between the headliner and roof is uncomplicated due to the fact that the printed circuit wiring can be attached to the headliner. This means that additional cable clips in the roof area are no longer required.Sun visor switch connection Vanity mirror light connectionCentral coupling point connection Front interior lightDescription The printed circuit wiring connects the rear interior light, the sun visor switch and the vanity mirror lighting to the onboard supply system. The central coupling point to the onboard supply system can be found on the front cross member, above the front interior light.Rear interior lightS319_073No provision has been made to repair the printed circuit wiring. It should be renewed in the event of a defect.52 Tuning guardIn the Golf 2004, a special guard is installed for the first time to protect the engine control unit. The tuning guard prevents engine control unit data from being accessed by unauthorised persons. Any attempt to alter the permanently stored data will be detected by the engine control unit. If an attempt is made to alter the data, the engine control unit will be disabled, thereby making it impossible to start the engine. The tuning guard is installed both on diesel and petrol engines.S319_05553 ServiceRear wiper renewalTo remove the rear wiper blade from the wiper arm, the mounting must be moved to the right in the direction of the arrow.After the wiper blade has been released, the wiper arm must be lifted away from the rear window to allow the wiper blade to be removed from the mounting.S319_04854 55 Test yourself1. Where can the data bus diagnostic interface J533 be found?… a) On the right beneath the dash panel, behind the glove compartment … b) In the dash panel insert … c) Beneath the dash panel, above the accelerator pedal2. What are the advantages of the powerless semi-conductor rotary light switch?… a) Bulb replacement function via control from onboard supply control unit … b) Coming home and leaving home function … c) Increase in bulb longevity … d) Activation of bulb failure warning lamp in dash panel insert3. What systems are switched off in transport mode for transportation of the vehicle?… a) Auxiliary heater telestart receiver, radio remote control, radio, interior monitoring, interior light,vehicle inclination sensor, alighting aids… b) Auxiliary heater telestart receiver, radio remote control, radio, interior monitoring, fog light,interior light, vehicle inclination sensor, alighting aids… c) Vehicle inclination sensor, driving lights, radio remote control, auxiliary heater telestart receiver,interior monitoring, interior light, alighting aids, radio56 4. Which control units are responsible for tyre pressure monitoring?… a) Control unit in dash panel insert J285, data bus diagnostic interface J534 and ABS withEDL control unit J104… b) ABS with EDL control unit, data bus diagnostic interface, dash panel insert control unit and tyrepressure monitor display control unit… a) Data bus diagnostic interface J533, ABS with EDL control unit J104 and control unit with display indash panel insert J2855. Which lights are joined by the printed circuit wiring?… a) Radio and heater display … b) Ashtray lights and cockpit illumination … c) Reading lamps and interior lights … d) Vanity mirror light and interior lights57 Answers: 1. c 2. c, d 3. a 4. c5. b, c, d58Test yourself 319For internal use only © AG, Wolfsburg VK 36, Service Training All rights and the right to make technical alterations reserved 000.2811.40.20 Technical status 10/03❀ This paper was manufactured from pulp thatwas bleached without the use of chlorine.