TECHNICAL DOCUMENTATION
SSP 374 Traction Control ESP

This PDF is currently unavailable.
Read document text
SERVICE TRAININGSelf-study Programme 374Traction Control and Assist SystemsDesign and functionCommercial VehiclesIncreasing speed and road traffic density are increasing the need for vehicle dynamics which offer the highest possible level of safety under all operating conditions. This is being achieved via a rising number of traction control and assist systems, some of which have been derived from the anti-lock brake system (ABS) and which support the driver.This fundamental information booklet provides an overview of these systems. In addition, their fundamental functional principles and which components work together in the relevant systems are explained.S374_010This self-study programme imparts the basics of the design and function of new vehicle models, new vehicle components or new technologies. The self-study programme is not a workshop manual!. The contents will not be updated.Specified values serve only to facilitate understanding and refer to the software status valid at the time at which the SSP was created. For testing, servicing and repair work, please use the current technical literature under all circumstances.Further informationNote2ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 About this booklet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Overview of the abbreviations which are used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Classification of the systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Passive and active speed sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Acceleration sensors and the yaw rate sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Traction control systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Anti-lock brake system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Brake systems with brake intervention only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Brake systems with additional engine intervention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Electronic stabilisation programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Auxiliary ESP functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Hydraulic brake assist system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Hydraulic brake servo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Overboost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Full rear axle deceleration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Vehicle/trailer stabilisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Roll-over prevention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Assist systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 Hill descent assist system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Hill start assist system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 AUTO HOLD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Dynamic starting assist system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Brake disk dry braking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Countersteering support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Adaptive cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Front assist system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80Annex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Test yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 853IntroductionAbout this bookletAs announced on page 2, this fundamental information booklet deals with the basic structure of the various traction control and assist systems, which influence the vehicle dynamics via the brake system or engine intervention. The various systems usually make use of the same types of sensor. The chapters dealing with the traction control and assist systems are therefore preceded by a brief chapter concerning the manner in which certain new sensors function.Information on further sensors, which work in the systems , can be found in self-study programme 204 "ESP Electronic Stability Programme" and in Skoda SSP No. 28 and No. 42.The chapter entitled "Traction control systems" explains the structure and the way in which the individual brake systems function. The anti-lock brake system ABS is regarded as the origin of all traction control systems and the electronic stabilisation programme ESP as the higher-level system in this case. The chapter on auxiliary ESP functions provides an overview of the ESP function software extensions which are currently available. The assist systems have the task of relieving the driver under certain conditions or during driving manoeuvres such as e.g. starting off on a hill. They do not actually belong exclusively to the topic of the running gear and brakes. The assist systems portrayed in this booklet are listed because they are integrated as functions into the ABS/ESP control unit or make extensive use of ESP system functions, such as e.g. its sensor system.4Overview of the abbreviations which are usedS374_077 Designation Active Roll-over Protection Adaptive Cruise Control Stopping distance reduction 1 Stopping distance reduction 2 Anti-lock Brake System Traction Control System Auto-Hold Driver Steering Recommendation Dynamic auto release Electronic Parking Brake Electronic Brake pressure Distribution Electronic Differential Lock Electronic Stabilisation Programme Extended anti-lock brake system Cornering Brake Control Fading Brake Support Front Scan Assist Yawing moment build-up deceleration Hill Descent Control Hill Hold Control Hill Start Assist Full Rear Axle Deceleration Hydraulic brake servo Hydraulic Brake Assist system Engine intervention anti-lock brake system (extended anti-lock brake system) Engine Braking effect Control Rain Brake Support Ready Alert Brake Roll-Over Programme Trailer Stabilisation Assist system ARP ACC AWV1 AWV2 ABS TCS AHA DSR DAR EPB EBD EDL ESP ABSplus CBC FBS FSA GMA HDC HHC HSA FRAD HBS HBA E-ABS EBC RBS RAB ROP TSA VW designation ROP – Roll-Over Prevention ACC – Adaptive Cruise Control AWV1 AWV2 ABS TCS Auto-Hold Countersteering support DAR Electromechanical Parking Brake EBD EDL ESP ABSplus CBC - Cornering Brake Control Overboost Front Assist YMC – Yaw Moment Control Hill descent assist system HHC – Hill start assist system HSA - Hill Start Assist (hill start assist system in the Touareg and T5) FRAD HBS HBA E-ABS EBC BSW – Brake disk dry braking Prefill ROP – Roll-Over Prevention Vehicle/trailer stabilisation5IntroductionClassification of the systemsDue to the multitude of control systems, it is difficult to classify the traction control and assist systems logically and clearly. Amongst other aspects, the systems are hierarchically linked to each other, some are at more developed stages and others are based on the others' hardware or software or are additions to existing functions. One option for classifying them is to assign the traction control and assist systems to the vehicle operating statuses of "starting off", "driving" and "braking". The following illustration shows which system may intervene in which vehicle operating status.Starting off EDL TCS E-ABS HHC AUTO HOLD DAR HSADriving ACC TCS ESP EBC BSW E-ABS Countersteering support ROP Hill descent assist system Vehicle/trailer stabilisationBraking ABS EBD CBC ABSplus YMC HBA HBS FRAD Front Assist ESP OverboostS374_032A further and more detailed option for classifying them is to sub-divide the traction control systems into two groups. Firstly, those systems with brake intervention solely via the hydraulic brake system and secondly, those which additionally influence vehicle dynamics via the engine management system or gearbox management system.6ESPBrake systems with engine management system intervention onlyE-ABSEBCTCSHBAHBS FRADVehicle/trailer stabilisationBrake systems with brake intervention onlyABSROP Overboost S374_030EBDEDLCBCABSplusYMCThe anti-lock brake system ABS is the source of all traction control systems, and is a brake system with brake intervention only. The software extensions and extensions via additional ABS system components include EBD, EDL, CBC, ABSplus and YMC. TCS is an extension of the ABS system. In addition to active brake intervention, this also enables intervention in the engine management system. The brake systems with engine management system intervention only include E-ABS and EBC. All traction control systems are subordinate to the ESP system, when ESP is fitted in the vehicle. If the ESP function is shut down, certain of the traction control systems function autonomously. The electronic stabilisation programme ESP intervenes independently in the vehicle dynamics when the control electronics ascertain a deviation between the driver's command and the vehicle's actual behaviour. This means that the electronic stabilisation programme ESP decides the vehicle dynamic conditions, and when, which traction control systems are activated or deactivated. ESP is the master function, so to speak. In this booklet, the ESP extensions are called auxiliary ESP functions, and necessitate the vehicle's being equipped with ESP.7SensorsGeneral informationTo enable a person to respond to their environment, in order e.g. to avoid an approaching danger, they must be able to perceive (sense) their surroundings. To do this, we make use of our senses, which are given to us by nature. We have optical sensors (eyes), acoustic sensors and our sense of balance (ears), sensors which react to chemical substances (nose & sense of taste) and sensors which react to contact (sense of touch) or temperature. Our ears are actually a sensor cluster, i.e. an amalgamation of several sensors, as we can register both sound and acceleration with them.Control unitActuatorsS374_001 SensorsA comparable situation applies to motor vehicles and their traction control and assist systems. To enable these systems to work, in order to defuse critical vehicle dynamics situations or prevent them from occurring, they must be equipped with sensors which enable them to register the driving situation. In particular, these include the speed sensors, acceleration and torque sensors. However, pressure sensors, yaw rate sensors or Hall sensors are used in the various systems, e.g. to register a pedal position. This booklet restricts itself to revealing the difference between active and passive speed sensors. It will also introduce the new sensor cluster. In addition to longitudinal and lateral acceleration senders, this now also contains a yaw rate sensor.ABS/ESP control unitButtonBrake light switchHydraulic unitSteering angle senderReturn flow pump Speed sensorS374_002Sensor clusterSensorsData bus connectionActuatorsFor more detailed information on the traction control system sensors, please refer to self-study programme 204 "ESP Electronic Stability Programme" and Skoda SSP No. 28 and No. 42.8Passive and active speed sensorsBoth types of sensor serve to inform the system of the vehicle speed and, much more importantly, the individual wheel speeds. The systems use differences in the wheel speeds to determine e.g. whether the tyres are located on a road surface with different levels of grip and there is therefore a risk of a critical vehicle dynamics situation occurring under braking.Passive speed sensorsThis involves the older generation of speed sensors. They have no separate current supply, leading to the name passive sensor. They usually operate according to the induction principle.DesignMagnetic field S374_026A sensor element and a reference system are basically required for speed measurement. The sensor element essentially consists of a coil, which is wrapped around an iron core, and a permanent magnet. The reference system is formed by a toothed ring (incremental or pulsed ring). In addition to the acceleration sensors in the ESP system, the speed sensors supply essential information.Reference system (sender wheel) CoilPermanent magnet Sensor element9SensorsHow it works If a piece of iron is passed through the magnetic field of a permanent magnet, the strength and shape of the magnetic field change. This change in the magnetic field can be detected with the aid of a coil, as the change in the coil's magnetic field leads to the induction of a voltage, which can be measured. The way in which this type of sensor operates is therefore called the induction principle. Each tooth on the impulse rotor which passes into the sensor's magnetic field therefore leads to an induction voltage. The sequence of voltage peaks within a time interval (frequency) can be used to calculate the wheel speed. Advantages/disadvantages The advantage of passive induction speed sensors is the simple design of the components. The disadvantage is their reliance on a precise gap dimension between the sender rotor and sensor. In addition, the passive induction speed sensors are heavier and require more installation space. As not only the frequency, but also the signal voltage, is dependent on the speed of the sender rotor, passive sensors only supply signals with a lower signal voltage at low speeds, in contrast to active sensors.Sensor signal at low speedS374_024Low frequency and voltageSensor signal at high speedS374_022High frequency and voltageThe signal is unable to reveal whether the sensor is faulty.10Active speed sensorsIn contrast to the passive sensors, the active sensors have a separate voltage supply. This is approx. 12 V. The functional principle of active speed sensors is based on the Hall principle or the magnetoresistive effect.Reference system (pole rotor)Magnetic field sensor Sensor electronicsDesign Active sensors comprise of a sensor element and a reference system. The sensor element is formed by a magnetic field sensor with sensor electronics. The reference system is a plastic ring with opposingly magnetised surface areas (pole rotor).S374_006 Supply and signal line GroundHow it works If a magnetic field sensor is passed through an alternating magnetic field, its Hall voltage changes; in the case of the magnetoresistive principle, the resistance changes. The faster the opposingly poled magnetic fields of the reference ring pass by the magnetic field sensor, the more frequently the Hall voltage changes. This type of sensor therefore also uses the frequency of voltage changes to calculate the wheel speed. Advantage/disadvantage Active speed sensors supply a constantly accurate measurement result throughout the entire measurement range, because the signal strength is not dependent on the speed, but is specified via defined currents. The disadvantage is the difficulty of checking with an ohmmeter.Opposing magnetic orientationSensor signal at low speedS374_007Low frequencySensor signal at high speedS374_008High frequency11SensorsAcceleration sensors and the yaw rate sensorThese act as the second, very important, group of sensors for traction control systems. Via these, the different functions find out the direction in which the vehicle is being accelerated or decelerated and whether the yaw rate occurs around the vehicle's vertical axis. These data enable the control systems to work out the direction in which the vehicle is actually moving, or which forces are acting on the vehicle and may be influencing the direction of movement. As these sensors react very sensitively, they can be used to detect critical situations as they arise and to introduce countermeasures.Vehicle inclination around the vehicle's longitudinal axis (rolling)Yaw rate around the vehicle's vertical axis (yawing) Vehicle centre of gravityLateral forcesDecelerating forcesS374_009 Vehicle inclination around the vehicle's transverse axis (pitching) Lateral forces Accelerating forcesCertain sensors are not required for ABS and E-ABS.12ESP sensor unit G419This sensor unit is a combination of the lateral acceleration sender G200, the longitudinal acceleration sender G251 and the yaw rate sender G202. Both acceleration sensors operate according to the capacitive principle and differ only as regards the sensors' spatial orientation to the relevant acceleration direction.S374_090Partial capacitor 1C1=C2 S374_036 Partial capacitor 2In vastly simplified terms, capacitive principle means that the sensor consists of two partial capacitors with a common capacitor plate, which can be moved via a force. Due to different inertias, the common capacitor plate moves relative to the two other capacitor plates when acceleration or gravity acts on the sensor. This shift in the common sensor plate changes the capacities, i.e. the electrical storage capability of the partial capacitors, in such a way that the extent of the acceleration can be concluded via the ratio of capacity C1 to C2. This type of sensor is implemented via a micromechanical system consisting of silicon, in which comb-like structures engage in each other and form the "capacitors".Moveable capacitor plateC1C2 S374_04013SensorsThe yaw rate sender operates according to the resonance principle and records the rotational speed around the vehicle's vertical axis (yaw rate). In this principle, part of a double tuning fork-shaped silicon crystal is caused to vibrate with the aid of a supply voltage. Due to the effect of the Coriolis force, the resonance behaviour of the other part of the double tuning fork changes. This can be measured electrically and used as a measure for the yaw rate.Resonance vibrationExcitation tuning forkMeasurement tuning fork Yaw rate S374_038For the precise functional principle of the individual sensor elements, please refer to self-study programme 204 "ESP Electronic Stability Programme" and Skoda SSP No. 28.The function of the yaw rate sender is explained here using the example of the tuning fork principle. Other functional principles also exist for such sensors, i.e. Coriolis acceleration and the micromechanical principle.14Traction control systemsThe control intervention carried out by the various traction control systems prevents the wheels from locking in various critical driving situations. The objective is to stabilise the vehicle's behaviour at all times and to maintain steerability. As explained in the introduction, the traction control systems are broken down into those systems which influence vehicle dynamics exclusively via the hydraulic brake system and those which additionally act via the engine management system and, if necessary, the gearbox management system in vehicles with automatic gearboxes.The first group includes: - The anti-lock brake systemABS, - Electronic brake pressure distribution EBD, - Corner brake control CBC, - The electronic differential lock EDL, - The extended anti-lock brake system ABSplus and - Yaw moment control YMC (yawing moment build-up deceleration GMA). The second group includes: - The traction control system TCS, - Engine braking effect control EBC and - The engine intervention anti-lock brake system E-ABS (extended anti-lock brake system).The anti-lock brake system ABS is the source of all traction control systems. Many of the listed systems represent an extension of the original ABS function's software. None of the listed brake systems require the vehicle to be equipped with ESP, but are functional by themselves when the vehicle is fitted with an ABS brake system. The EDL function requires an extended hydraulic unit.The electronic stabilisation programme ESP independently intervenes, via the brake system, in the vehicle dynamics when the control electronics ascertain a deviation between the driver's command and the vehicle's actual behaviour. ESP can be regarded as a higher-level system.15Traction control systemsAnti-lock brake systemIf we regard ESP as the higher-level system, the anti-lock brake system ABS is the source of all traction control systems. The first electronic ABS control systems were used in 1969.During full braking, one or more wheels always tend to lock uplock up earlier than the others because the friction between the wheels and the road surface changes constantly as a result of many influences. A locked-up wheel is also referred to as 100% slip. In this case, the locked-up wheels slip across the road surface like an eraser on paper. When frictional adhesion is lost, the establishment of lateral guidance forces, which keep the vehicle on course, is impossible. The vehicle breaks away as a result of the centrifugal force and can no longer be steered.Vehicles without ABS S374_041In the event of full braking on the wet road surface, the wheels lock up. The vehicle begins to skid.Combating this hazardous driving situation only became possible when the first ABS systems which were adequate for series production were introduced. ABS increases the vehicle's stability by preventing the wheels from locking up on braking. It reduces the brake pressure at the corresponding wheels to such an extent that the maximum frictional adhesion can be transmitted. As a result, forces can again be transmitted onto the road surface, and it remains possible to steer the vehicle.Vehicles with ABS S374_043Reducing the brake pressure at the wheels on the wet road surface prevents the wheels from locking up. It remains possible to steer the vehicle.16Design The ABS system consists of:●● ● ● ● ●The hydraulic unit with - Electric return flow pump, - Two damping chambers and - Two pressure accumulators plus - Four ABS inlet and outlet valves each, - Several non-return valves, which ensure that the brake fluid flows in the necessary direction. The ABS control unit, The four speed sensors, The brake light switch to detect brake actuation, The ABS warning lamp and Two separate brake circuits, which are supplied with brake fluid and brake pressure via a brake servo.ABS warning lamp Speed sensor Tandem brake master cylinderSpeed sensor S374_045 Brake light switchABS control unit with hydraulic unitSplitting the brake system into two separate brake circuits increases the vehicle's safety. If one circuit fails, the vehicle can still be brought to a stop via the second brake circuit. The system can be sub-divided into the front axle and rear axle brake circuit or diagonally (left front wheel/ right rear wheel and right front wheel/left rear wheel). Diagonal sub-division is usually implemented.Within a brake circuit, one ABS inlet valve and one ABS outlet valve is assigned to each wheel brake cylinder. As a result of this, each wheel brake can be actuated individually. The low-pressure accumulator in each brake circuit supports fast pressure reduction from the wheel brake cylinder. Transporting the hydraulic fluid back from the low-pressure accumulator to the reservoir is carried out by the return flow pump. This is designed in such a way that both brake circuits have a separate return flow stage, both of which are driven by a common electric motor.17Traction control systemsABS hydraulic circuit diagram124358 7 9 10 12 11614 13 161517 1819 20 23 24 S374_30821 22Legend 1 2 3 4 5 6 7 8 9 10 11 12 Reservoir Brake servo Brake pedal sensor system Brake pressure sender ABS/ESP control unit Return flow pump Pressure accumulator Damping chamber Front left ABS inlet valve Front left ABS outlet valve Rear right ABS inlet valve Rear right ABS outlet valve 13 14 15 16 17 18 19 20 21 22 23 24 Front right ABS inlet valve Front right ABS outlet valve Rear left ABS inlet valve Rear left ABS outlet valve Front left wheel brake cylinder Front left speed sensor Front right wheel brake cylinder Front right speed sensor Rear left wheel brake cylinder Rear left speed sensor Rear right wheel brake cylinder Rear right speed sensorInlet valve IV(9): OpenS374_310Outlet valve OV(10): OpenS374_316Inlet valve IV(9): ClosedS374_312Outlet valve OV(10): ClosedS374_31418How it worksBrake actuation by the driver 1 - Foot brake depressed 2 - Tandem brake master cylinder 6 - Return flow pump 7 - Pressure accumulator 8 - Damping chamber 9 - ABS inlet valve 10- ABS outlet valve 17- Wheel brake cylinder 18- Speed sensorIn contrast to ESP, ABS requires the driver to actuate the brake. The system does not act independently. On braking, ABS compares the speeds of the four wheels. If there is a danger of individual wheels locking up, ABS prevents a further increase in brake pressure. The driver perceives ABS control intervention as slight brake pedal pulsation. This arises due to the changes in brake pressure during ABS intervention. The vehicle's steerability is maintained, because ABS prevents individual wheels from locking up. The ABS function cannot be manually deactivated.1 26 8 791017 18 S374_3021 2ABS regulation "maintain pressure" 1 - Foot brake depressed 2 - Tandem brake master cylinder 6 - Return flow pump 7 - Pressure accumulator 8 - Damping chamber 9 - ABS inlet valve 10- ABS outlet valve 17- Wheel brake cylinder 18- Speed sensorPressure maintenance If the ABS control unit ascertains that a wheel is in danger of locking up, the control system closes the affected wheel's ABS inlet valve whilst the ABS outlet valve is closed at the same time. As a result of this, the pressure in the wheel brake cylinder is maintained and cannot be increased further by the driver's depressing the brake. IV(9): Closed OV(10): Closed6 8 791017 18 S374_30419Traction control systemsPressure reduction If the tendency to lock up remains, the control system opens the ABS outlet valve with the ABS inlet valve closed. The wheel cylinder's pressure can now be released into the pressure accumulator. As a result, the wheel is able to accelerate again. If the capacity of the pressure accumulator is not sufficient to eradicate the wheels' tendency to lock up, the ABS control system switches the return flow pump on to pump the brake fluid back into the reservoir counter to the brake pressure applied by the driver. This causes the pulsation in the brake pedal. IV(9): Closed OV(10): OpenABS regulation "reduce pressure" 1 - Foot brake depressed 2 - Tandem brake master cylinder 6 - Return flow pump 7 - Pressure accumulator 8 - Damping chamber 9 - ABS inlet valve 10- ABS outlet valve 17- Wheel brake cylinder 18- Speed sensor216 8 791017 18 S374_306Pressure build-up If the wheel speed again exceeds a defined value, the control system closes the ABS outlet valve and opens the ABS inlet valve. The return flow pump continues to run as required. If the lock up limit is reached again, the "maintain pressure", "reduce pressure" and "build up pressure" cycle is repeated until the braking process is completed or comparison of the wheel speeds shows that there is no further danger of the wheels' locking up. IV(9): Open OV(10): ClosedABS regulation "build up pressure" 1 - Foot brake depressed 2 - Tandem brake master cylinder 6 - Return flow pump 7 - Pressure accumulator 8 - Damping chamber 9 - ABS inlet valve 10- ABS outlet valve 17- Wheel brake cylinder 18- Speed sensor1 26 8 7 9 1017 18 S374_32820Brake systems with brake intervention onlyIn the case of the following traction control systems, a critical driving situation is combated by means of brake intervention via the hydraulic brake system. These traction control systems include:● ● ● ● ●Yaw moment control YMC, Electronic brake pressure distribution EBD, Cornering brake control CBC, The electronic differential lock EDL and The extended anti-lock brake system ABSplus.Yaw moment controlIn the past, yaw moment control YMC was also called yawing moment build-up deceleration GMA. It frequently occurs that a passenger car's four wheels roll on road surfaces with varying grip. For example, it may be the case that road surface defects have been filled with chippings or that parts of the road surface have been worn smooth to varying degrees, as in ruts. During braking manoeuvres, it may therefore be the case that, due to the road surface's different grip levels, yawing moments occur around the vehicle's vertical axis. These attempt to send the vehicle off course. An ABS control system software extension enables this yawing moment to be combated by temporally limiting the difference in brake pressure build-up between the left and right wheels to different degrees. This is therefore referred to as yaw moment control. A brake pressure difference is built up slowly to give the driver more time to react.Due to yaw moment control YMC, the stopping distance is extended, by necessity, in favour of improved vehicle stability.21Traction control systemsVehicle without YMC Vehicle with YMCS374_065 The side of the vehicle on the surface with better grip is braked more extensively than the side of the vehicle on the smooth surface. The yawing moment which occurs in this case causes a yaw rate, which the driver cannot compensate quickly enough via the steering.S374_067 The brake pressure at the wheels on the surface with better grip does not increase so quickly. The dangerous yaw rate is overcome.How it works If the ABS control system within the YMC function ascertains during a braking manoeuvre that the wheel speeds of the wheels on the left-hand side deviate from those on the right-hand side, the system concludes that disturbing yawing moment may develop. Braking the wheels with the higher speed is therefore delayed slightly until the wheel speeds on the right- and left-hand sides match each other again. To achieve this, the relevant ABS inlet valves are opened slightly later by the control system, with the result that pressure buildup at the wheel brake cylinder takes place more slowly.22Electronic Brake pressure DistributionIf the vehicle's rear axle locks-up, the vehicle is unstable and can break away in an uncontrolled manner. The electronic brake pressure distribution (EBD) function exists to avoid this critical driving condition.S374_055Due to weight distribution in the vehicle, rear axle wheel load is significantly lower than that on the front axle. To achieve controllable vehicle dynamics, brake pressure distribution has been defined such that the front axle brakes should lock up before the rear axle brakes (Directive ECE13; ECE=Economic Commission for Europe), in order to maintain residual vehicle stability in the longitudinal direction.Weight distribution in the vehicle reveals higher axle load at the front axle.S374_014When braking hard, the vehicle weight is shifted onto the front wheels. The vehicle pitches around its transverse axis. Due to this movement, the rear axle is relieved. As a result, the rear wheels are able to lock up, as the brake power can no longer be applied onto the road due to the reduced ground contact. The brake force distribution directive would therefore be violated.Due to the pitching motion on braking, the axle load at the front axle is increased and the rear axle is relieved.23Traction control systemsBased on the speed sensors, the control system detects the rear axle overbraking which occurs in the case of pitching. Via solenoid valves in the ABS unit, the EBD system regulates the brake pressure for the rear wheels and thereby ensures maximum brake power at the front and rear axles. This prevents the rear end from breaking away due to rear wheel overbraking.S374_012 Brake pressure Brake pressureBrake pressure at the front axleBrake pressure reduction at the rear axleEBD function prevents rear axle overbrakingThis rear axle overbraking effect was originally overcome via mechanical brake pressure distributors. On introduction of the ABS system, the brake pressure distribution function was also implemented via the vehicle's hydraulic brake system. Pitching motions on braking and lateral inclination on cornering contribute towards an extensive variation in wheel load depending on the driving situation. Consequently, the brake pressures have to be distributed in different ways. In contrast to mechanical brake pressure distribution, the EBD system is able to regulate the brake pressure individually for each rear wheel. Consideration can therefore also be given to different road surface conditions. EBD detects the deceleration of one or both rear wheels and reduces the brake pressure at the corresponding wheel. The EBD system's range of action ends as soon as a wheel reveals an increased tendency to lock up. ABS intervenes in this case.S374_057 Different brake pressure distribution between the two rear wheels due to different road surface conditions24Design The EBD function does not require any additional components; it uses the components available in the ABS system. Electronic brake pressure distribution is an extension of the ABS system's software.How it works The wheel speeds on the front and rear axle are compared. If the difference exceeds a maximum value, overbraking is detected on the rear axle and the EBD system intervenes. The EBD system then closes the ABS inlet valves for the left and/or right rear wheel, thereby preventing further pressure build-up and maintaining the pressure in the wheel brake cylinder. Whilst the front wheel inlet valves are open to build up brake pressure, the rear wheel outlet valves are already closed. In the event of further rear axle overbraking, the relevant ABS outlet valves are additionally opened to reduce brake pressure. In the event of underbraking, the pressure level is increased to enable the transmission of as much brake pressure as possible. This enables optimal exploitation of the potential frictional connection. Expressed simply, EBD is therefore ABS regulation which only acts on the rear wheels with its three phases: "Maintain pressure", "reduce pressure" and "build up pressure".2 16 8 7 Legend 1 - Foot brake depressed 2 - Tandem brake master cylinder 6 - Return flow pump 7 - Pressure accumulator 8 - Damping chamber 9 - ABS inlet valve 10 - ABS outlet valve 15 - Rear left ABS inlet valve 16 - Rear left ABS outlet valve 17 - Front left wheel brake cylinder 18 - Front left speed sensor 21 - Rear left wheel brake cylinder 22 - Rear left speed sensor9 10161517 18 Front wheel21 22 Rear wheel S374_33025Traction control systemsCornering Brake ControlIn the past Cornering Brake Control CBC was also referred to as Extended Stabilised Braking System ESBS. Depending on the situation, dangerous cornering behaviour on braking can be expressed as oversteering or understeering on cornering. In extreme cases, this may lead to the vehicle's skidding. This behaviour is based on the fact that yaw rates, which lead to the described vehicle behaviour, can occur during braking manoeuvres on cornering. CBC overcomes these yaw rates. To achieve this, the wheel brakes are specifically actuated by the CBC control system during the braking manoeuvre, in order to build up an opposing, corrective yaw rate. CBC improves the vehicle's stability when braking on cornering.UndersteeringS374_053 If a vehicle without CBC is braked extensively on cornering, the wheel location forces on the front wheels are reduced. The vehicle pushes over the front axle towards the outer edge of the curve.Design The CBC does not require any additional components; it uses the components which are available in the ABS system. The CBC system is also a pure extension of the ABS control system's software. Its special feature is that the system is able, without yaw rate or lateral acceleration sensors, to recognise hazardous situations, particularly during braking manoeuvres on cornering, solely on the basis of the wheel speeds.S374_049 In vehicles with CBC, the brake pressure on the front axle is reduced in the event of understeering. As a result, the wheel location forces are increased and the vehicle remains on course.26OversteeringHow it works CBC comes into effect when the wheels display slip below the ABS control range. The CBC system recognises this situation based on the speeds of the individual wheels. Via further analysis, the ABS control unit is able to recognise oversteering or understeering and regulate the brake pressure accordingly. As in the case of ABS regulation, brake pressure regulation takes place in three phases: "Maintain pressure", "reduce pressure" and "build up pressure".S374_051 If a vehicle without CBC, which enters a curve at an excessive speed, is steered and braked too severely, the rear end breaks away to the outer edge or the curve.The vehicle's behaviour is stabilised and steerability is maintained. If the ABS regulation limit is reached in the event of slip, the ABS takes precedence over CBC. This means that CBC is deactivated and ABS prevents the wheels from locking up.S374_047 In vehicles with CBC, the brake pressure at the inner wheels is reduced in the event of oversteering. This increases the wheel location forces at the inner wheels and the vehicle's rear end remains stable.27Traction control systemsElectronic Differential LockThe Electronic Differential Lock EDL was originally designed as a starting aid. EDL intervenes in the vehicle dynamics if one of the drive wheels spins on accelerating. The spinning wheel is braked. Thanks to the brake's specific intervention, the drive torque which can be transmitted at the spinning wheel is increased. The differential is able to transmit more drive torque to the gripping wheel on the drive axle. The vehicle accelerates faster and remains steerable. As the effect corresponds approximately to that of the mechanical differential lock, the system was called the electronic differential lock.Vehicle without EDLVehicle with EDLS374_061 The vehicle can only be accelerated with the drive power transmitted to the spinning wheel, because the differential is able to pass on only the smaller of an axle's two drive torques. The vehicle is only able to accelerate very slowly.S374_063 The wheel on the wet road surface is braked and the slip is limited. As a result, the drive power is increased via the differential and transmitted to the wheel which is not spinning. The vehicle with EDL reaches a higher speed in the same time.EDL intervention can take place up to a speed of 80 km/h (Touareg up to 120 km/h) and also during cornering. On actuation of the brake pedal or at a maximum brake disk temperature, which is calculated by the ABS control unit, the EDL is deactivated immediately.28Design1 2Resting position 1 - Reservoir 2 - Brake servo 6 - Return flow pump 7 - Pressure accumulator 8 - Damping chamber 9 - ABS inlet valve 10- ABS outlet valve 17- Wheel brake cylinder 18- Speed sensor 25- Switch valve 26- High-pressure valve25Essentially, an ABS brake system with EDL differs from a pure ABS brake system in that the ABS system with EDL is able to independently build up brake pressure. EDL uses the ABS system's speed sensors without any technical extensions. The software in the ABS control unit is extended by the EDL function. This is achieved by means of additional valves and a self-priming return flow pump in the hydraulic unit. If the control unit detects a situation in which the EDL has to intervene, the brake pressure in the spinning wheel's brake circuit can be built up without having to actuate the brake pedal.6268 7 9 1017 18 S374_320How it works1 2EDL regulation "build up pressure" 1 - Reservoir 2 - Brake servo 6 - Return flow pump 7 - Pressure accumulator 8 - Damping chamber 9 - ABS inlet valve 10- ABS outlet valve 17- Wheel brake cylinder 18- Speed sensor 25- Switch valve 26- High-pressure valve25Based on the wheel speeds, the EDL ascertains that one of the drive axle's wheels has higher slip, i.e. it is rotating faster than the other drive wheel. EDL therefore has to brake the spinning wheel so that drive power can also be transmitted again there. Regulation takes place, like that of the ABS system, in three phases: "build up pressure", "maintain pressure" and "reduce pressure". Pressure build-up To build up pressure, the switch valve is closed and the high-pressure valve is opened. The return flow pump begins working and takes in brake fluid from the brake master cylinder. As a result, brake pressure builds-up in the spinning wheel's brake cylinder and the wheel is braked.6268 7 9 1017 18 S374_32229Traction control systemsPressure maintenance To maintain the brake pressure in the wheel's brake circuit, only the return flow pump is deactivated. The switch valve remains closed. A constant brake pressure is maintained at the wheel brake.EDL regulation "maintain pressure" 1 - Reservoir 2 - Brake servo 6 - Return flow pump 7 - Pressure accumulator 8 - Damping chamber 9 - ABS inlet valve 10- ABS outlet valve 17- Wheel brake cylinder 18- Speed sensor 25- Switch valve 26- High-pressure valve1 2256268 7 9 1017 18 S374_324Pressure reduction To reduce pressure, the inlet valve and the switch valve are currentless, i.e. opened.EDL regulation "reduce pressure" 1 - Reservoir 2 - Brake servo 6 - Return flow pump 7 - Pressure accumulator 8 - Damping chamber 9 - ABS inlet valve 10- ABS outlet valve 17- Wheel brake cylinder 18- Speed sensor 25- Switch valve 26- High-pressure valve1 2256268 7 9 1017 18 S374_32630Extended anti-lock brake systemThe extended anti-lock brake system ABSplus is a software extension in the ABS/ESP control unit. Thanks to ABSplus, the stopping distance can be reduced by up to 20 percent on loose surfaces, such as gravel or sand, for example. ABSplus makes use of the ESP sensors. The existing surface is recognised on the basis of the ABS sensors and the ABS control unit. The stopping distance is reduced by temporarily locking up the wheels in a controlled manner. As a result of this, a socalled brake chock is built up in front of the wheels by pushing the loose surface together; this supports the braking effect and therefore reduces the stopping distance. However, the vehicle remains fully steerable, as the brakes open up again and allow the wheel to run freely.Vehicle without ABSplusVehicle with ABSplusS374_071 The driver of a vehicle without ABSplus actuates the brake pedal and the vehicle is braked on a loose surface.S374_069 In a vehicle with ABSplus, the wheels only lock up briefly on a loose surface, and therefore build up a chock consisting of the corresponding surface material in front of the tyres. This shortens the stopping distance.The extended anti-lock brake system ABSplus is currently fitted in the Touareg as standard.Brake systems with brake and/or engine interventionIn the case of the following traction control systems, a critical driving situation is overcome either via the engine management system and/or by means of brake intervention via the hydraulic brake system.● ● ●Engine braking effect control EBC, Engine intervention anti-lock brake system E-ABS and Traction control system TCS.31Traction control systemsEngine Braking effect ControlEngine Braking effect Control EBC recognises that slip is occurring at the drive wheels due to the engine's braking effect and requests corresponding drive torque from the engine, thereby facilitating the wheels' re-starting. Wheel slip phases are shortened and the vehicle's steerability is restored.During vehicle operation, the driver removes his foot from the accelerator and shifts to a lower gear. In the event of unfavourable road surface conditions, the brake pressure which results on the wheel can cause slip, which may lead to the wheels' locking up. EBC intervenes and reduces the engine's braking effect by increasing the engine torque. The EBC system therefore ensures the vehicle's stability and steerability.S374_094Drive torqueEngine braking effectIf the driver rapidly releases the accelerator during vehicle operation, the engine is throttled abruptly and the driving power is reduced. Frictional forces, which lead to an engine braking effect, occur within the engine in this case. This effect is also known as the engine brake. This engine braking effect, which acts in the same manner as brake pressure, counters the drive torque. Due to simultaneous downshifting to a lower gear, the engine braking effect is increased.Under unfavourable conditions in the case of vehicles with very high-powered engines, the engine braking effect may lead to the wheels' locking up or to such extensive slip that lateral guidance forces are lost and it becomes impossible to steer the vehicle. Engine braking effect control intervenes when the following conditions are met:● ● ● ●The accelerator is not actuated. The drive wheels are slipping or locked uplocked up. The gear has to be engaged. The clutch is not actuated.Engine braking effect control makes use of the engine management system to carry out its function.32How it works The prerequisites of engine braking effect control EBC are ABS components with an engine interface. The ABS software is extended by the EBC software. Based on the speed sensors and the necessary information from the engine management system (e.g. engine speed, throttle valve position, accelerator position), the ABS control system with EBC function is able to ascertain whether slip occurs at the driven wheels on reducing the engine torque by releasing the accelerator. If this is the case, the ABS/TCS control unit forwards this information to the engine control unit, which uses this to calculate the necessary nominal engine speed. To increase the engine speed in the case of EBC, the throttle valve is briefly opened until the drive wheel slip has returned to an optimal level. During this process, the system remains in a control range which makes optimal use of the engine braking effect, but which also simultaneously guarantees sufficient lateral guidance forces. EBC operates throughout the engine's entire speed range. Engine braking effect control EBC is ended by actuating the accelerator.Accelerator position Speed sensor, front left Nominal engine torque Speed sensor, front right Actual engine torqueSpeed sensor, rear leftABS/TCS control unitEngine control unitControl via the throttle valve Speed sensor, rear rightS374_09633Traction control systemsEngine intervention anti-lock brake systemThe engine intervention anti-lock brake system E-ABS is an extension of the ABS system's functional scope. It is intended to support the driver on starting off and to prevent the wheels from spinning. With E-ABS, the ABS control system has the option of intervening into the engine management system. It is not able to actively build up pressure.How it works If, on the basis of the wheel speeds and the engine management system information, which are transmitted via the CAN data bus, the ABS control system ascertains that the drive wheels are in danger of spinning, E-ABS instructs the engine management system to close the throttle valve further and thereby reduce the drive torque.Speed sensor, front left Nominal engine torque Speed sensor, front right Actual engine torqueControl via the throttle valveSpeed sensor, rear leftABS/TCS control unitEngine control unitSpeed sensor, rear rightS374_102E-ABS is unable to intervene hydraulically in the drive wheel brake cylinders. The system does not have the option or equipment to independently build up brake pressure via a pressurisation system without the involvement of the driver.34Traction Control SystemVehicle without TCSThe Traction Control System TCS supports the driver on starting off or accelerating on a slippery road surface by reducing drive slip. If the drive wheels are in danger of spinning, TCS is able to reduce the drive power● ●by specifically braking spinning wheels and by reducing the drive torque via intervention in the engine or gearbox management system.S374_073 The vehicle accelerates on a slippery road surface. The wheels spin and the vehicle is not accelerated or is only accelerated very slowly. On cornering, only insufficient lateral guidance forces can be transmitted and the vehicle cannot be steered.Unlike ABS, TCS does not therefore act within braking processes during the deceleration of a vehicle, but within vehicle acceleration. To enable intervention during vehicle acceleration, the system requires a link to the engine management system, enabling it to influence the drive torque, and the option of independently building up pressure in the brake system. This is necessary to be able to brake spinning wheels without the driver's building up the brake pressure via the brake pedal. TCS acts throughout the entire speed range. As of a vehicle speed of approx. 80 km/h, the driving power is reduced exclusively via intervention in the engine or gearbox management system.Vehicle with TCSTCS control intervention is indicated using the ESP and TCS warning lamp. The TCS and ESP button can be used to deactivate intervention in the engine management system.S374_075 TCS reduces the driving power and therefore prevents excessive slip at the drive wheels. The lateral guidance forces are able to act and the vehicle's driving behaviour remains stable.35Traction control systemsDesign TSC is based on the ABS system in both hardware and software terms. The TCS software is integrated into a higher-performance ABS control unit with an extended programme memory. The speed sensor signals are used as in the case of ABS. To enable the required functions to be carried out, the TCS system must be extended at two essential points in comparison with the ABS system.● ●2. Interface to the engine management system In contrast to ABS and also EDL, TCS acts not only on the brakes and therefore the deceleration of a wheel, but also on the engine output, i.e. the drive torque at the wheels. To achieve this, the accelerator must be mechanically decoupled from the throttle valve position. Regulation of the engine output must therefore be possible independently of the position of the accelerator. In the first ABS systems with TCS, the approaches to throttling the engine torque differed significantly. For example, systems with a second throttle valve or the option of ignition masking were implemented. On introduction of the CAN data bus systems and the electronic throttle function, it became possible to use this comfortable interface to influence the engine's torque and speed without additional components.Changes in the hydraulic unit Interface to the engine management system1. Changes in the hydraulic unit The EDL function is already integrated into TCS. Therefore, the valve configuration of the ABS hydraulic unit, consisting of two ABS inlet and outlet valves per brake circuit, is also extended by further valves here: - One switch valve - One high-pressure valve A self-priming return flow pump is also required in the hydraulic unit, in order to independently build up brake pressure.In principle, TCS is an EDL with engine intervention.36TCS hydraulic circuit diagram1227432526525266 8 79 10 12 11 13 14 16 1517 1819 2021 2223 24 S374_332Legend 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Reservoir Brake servo Brake pedal sensors Brake pressure sender ABS/ESP control unit Return flow pump Pressure accumulator Damping chamber Front left ABS inlet valve Front left ABS outlet valve Rear right ABS inlet valve Rear right ABS outlet valve Front right ABS inlet valve Front right ABS outlet valve 15 16 17 18 19 20 21 22 23 24 25 26 27 Rear left ABS inlet valve Rear left ABS outlet valve Front left wheel brake cylinder Front left speed sensor Front right wheel brake cylinder Front right speed sensor Rear left wheel brake cylinder Rear left speed sensor Rear right wheel brake cylinder Rear right speed sensor Switch valve High-pressure valve CAN data bus37Traction control systemsHow it works In a vehicle with TCS, the wheel rotational speeds are used to calculate the four wheel speeds. By means of an extended evaluation, the TCS software analyses the following driving situations:● ●With this information, TCS is able to recognise when the drive wheels are in danger of spinning. A signal regarding the actual engine torque is additionally read by the engine control unit. TCS uses this to calculate the measures to be introduced. In the low speed range, TCS regulation usually takes place via brake intervention. Regulation takes place, like that of EDL regulation, in three phases: "build upbuild up pressure", "maintain pressure" and "reduce pressure". In the case of TCS, brake intervention can be combined with intervention via the engine management system. TCS regulates throughout the entire speed range. As of a speed of 80 km/h, EDL regulation is discontinued.●●The driven wheels' acceleration is calculated. The vehicle speed is calculated from the non-driven wheels' speed. Curve detection arises from the comparison of the non-driven wheels' speeds. Drive slip is calculated from the difference in the speeds of the driven and non-driven wheels per side of the vehicle.RegulationS374_10080 km/hSpeed [km/h]TCS/EDL = intervention in the engine management system with brake intervention TCS/EDL = intervention in the brakes TCS = intervention in the engine management system38For intervention via the engine control unit, TCS uses the drive slip which has been determined and the actual engine torque to calculate a necessary nominal engine torque. This is transmitted to the engine control unit. Depending on the available engine management system, the engine control unit has the following options:● ●●●The engine torque is reduced by adjusting the throttle valve. In the event of control intervention via the injection system, the engine output is reduced by masking injection pulses. In the event of control intervention via the ignition system, either ignition pulses can be masked or the ignition timing can be adjusted in the "retarded" direction. In vehicles with automatic gearboxes, TCS additionally transmits a signal to the gearbox control unit, via which a gear change can be suppressed.Speed sensor, front leftControl via the throttle valve Nominal engine torque Actual engine torque Regulation via the injectorsSpeed sensor, front rightSpeed sensor, rear leftABS/TCS control unitEngine control unitRegulation via the ignition systemSpeed sensor, rear rightGearbox management systemS374_09239Traction control systemsElectronic Stabilisation ProgrammeNowadays, ESP means "electronic stabilisation programme". When the system was introduced, ESP stood for "electronic stability programme". With the aid of its sensors, the electronic stabilisation programme ESP recognises at an early stage that a critical driving situation is emerging. By specifically braking individual wheels and the possibility of intervention in the engine and gearbox management system, ESP then independently acts to counter this situation in such a way that vehicle stability and steerability are maintained. At present, ESP is the most advanced wheel traction control system. It is not an individual system; the wheel traction control systems ABS, EBD, CBC, EDL, YMC, TCS and EBC are already integrated. Each of these subsystems can operate both autonomously and in combination. ESP is superordinate to the other systems. The electronic stabilisation programme ESP decides when, and under which vehicle dynamics conditions, which traction control systems are implemented and controls their operation in combination. ESP is permanently in readiness. The recognition of a critical vehicle dynamics situation is based on comparison of the driver's command and the actual vehicle behaviour. If these deviate from each other, ESP control intervention begins. Depending on the situation, ESP reduces the engine torque and suppresses gear changes in the case of automatic gearboxes. ESP then stabilises the vehicle's behaviour by specifically braking individual, or several, wheels. On understeering, engine management intervention first takes place, in contrast to which brake intervention takes place first in the event of oversteering. Control intervention lasts until all unstable vehicle statuses have been corrected, i.e. the nominal value has been achieved again.By braking individual wheels, ESP generates a yaw rate around the vehicle's vertical axis. This yaw rate acts counter to the vehicle's direction of movement and stabilises travel in the desired direction. Hazardous understeering or oversteering is therefore effectively prevented.Understeering S374_117Oversteering S374_119On understeering, ESP prevents departure from the curve by specifically braking the inner rear wheel.On oversteering, the outer front wheel is braked.40Let us take a closer look at the vehicle's behaviour during evasive action.Vehicle without ESPThe vehicle without ESP has to evade an obstacle which suddenly emerges. The driver first steers very quickly to the left and immediately afterwards back to the right. The vehicle begins to sway due to the preceding steering movements, and the rear end breaks away. The rotation around the vertical axis can no longer be controlled by the driver. The vehicle begins to skid.S374_121Vehicle with ESPS374_123The vehicle with ESP attempts to evade the obstacle. ESP recognises that the vehicle is in danger of understeering to the left. The steering movement is initially supported by braking the left rear wheel. At the same time, intervention in the engine management system takes place via the CAN data bus in order to reduce the drive power and additionally brake the vehicle via the engine braking effect.Whilst the vehicle curves to the left, the driver steers to the right. To support this countersteering, the front right wheel is braked. As the driver wishes to return to his original course, he must now steer to the left again. The preceding lane change may lead to the vehicle's swinging around the vertical axis. The left front wheel is braked to prevent the rear end from breaking away.41Traction control systemsDesign The ESP system consists of: The ABS/ESP control unit The hydraulic unit with electronic return flow pump, The four speed sensors, The brake pressure sender, The TCS and ESP button, The brake light switch, The brake system warning lamp, The ABS warning lamp, The ESP and TCS warning lamp, The ESP sensor unit and The steering angle sender To a large extent, the ESP system makes use of the ABS and TCS components. A control unit with corresponding software and a hydraulic unit with return flow pump are available to regulate the brake pressures. The hydraulic unit must be designed for 4-wheel TCS. Warning lamps in the dash panel insert are used to inform the driver of control interventions which are taking place and the status of the ESP system. A button in the dash panel can be used to deactivate the ESP/TCS function. In certain vehicles, e.g. the Tiguan, only the TCS function is deactivated. Other brake systems, such as e.g. ABS, remain active even when the ESP function is deactivated.and in certain vehicles - An active brake servo or - A pre-charging pump.ABS warning lamp ESP and TCS warning lamp Brake system warning lamp TCS and ESP buttonSteering angle sender Speed sensorTandem brake master cylinderSpeed sensorS374_125Control unit and hydraulic unit with return flow pump Brake pressure senderBrake light switchESP sensor unit with the lateral acceleration sender, the yaw rate sender and the longitudinal acceleration sender. (Longitudinal acceleration sender in 4-Motion vehicles and vehicles with electromechanical parking brake)42The system's sensors are sub-divided into the senders for registering the driver's command and those for sensing the vehicle behaviour. The driver's command is registered by: - The steering angle sender, - Information from the engine control unit, - The brake light switch, - The brake pedal switch and - The brake pressure sender. The steering angle represents the driver's direction command and actuation of the brake pedals represents the command to brake or stop. The brake pressure sender additionally provides information on the intensity of the desired braking.The actual vehicle behaviour is registered by: - The speed sensors on all four wheels, - A sender for registering longitudinal and lateral acceleration, - A sender for sensing the yaw rate and - A sender for registering the current brake pressure. The speed sensor signals are used to determine the four wheels' drive and brake slip. The signals from the transverse acceleration sender, the longitudinal acceleration sender and the yaw rate sender provide information on the vehicle's longitudinal and transverse dynamics. The brake pressure sender registers the actual pressure in the brake system. In vehicles with automatic gearboxes, a link to the gearbox management system is added in order, firstly, to register the current gear selection and secondly to enable the gearbox to be shifted independently in the event of ESP control intervention.Driver command Direction of travel Desired speed Desired deceleration Steering angle sender Engine control unit Brake light switch and brake pedal switch Brake pressure sender Nominal vehicle behaviourVehicle behaviour Acceleration Deceleration Yaw rate (yawing moment) Longitudinal and transverse accelerationBrake pressure sender Speed sensor Longitudinal / transverse acceleration sender Yaw rate sender Gearbox control unitESP intervention when the vehicle does not behave as commanded by the driver Actual vehicle behaviourS374_130The ABS/ESP control unit uses the data from the driver's command to calculate the nominal vehicle behaviour and the actual vehicle behaviour from the vehicle's actual movements. By comparing the two values, the ESP software detects a critical driving situation, and the necessary control interventions are introduced.43Traction control systemsOverview of the system Sensors ActuatorsTCS and ESP button E256 Diagnosis connector Brake light switch F Hydraulic unit with ABS return flow pump V39 Vehicle stabilisation programme switch valve 1 N225 Vehicle stabilisation programme switch valve 2 N226 Vehicle stabilisation programme highpressure valve 1 N227 Vehicle stabilisation programme highpressure valve 2 N228 ABS inlet valves N99, N101, N133, N134 ABS outlet valves N100, N102, N135, N136Brake pedal switch F47Speed sensor, rear right G44, front right G45, rear left G46, front left G47ABS control unit with EDL/TCS/ESP J104CANSteering angle sender G85 Auxiliary signals Engine management system Gearbox management systemESP sensor unit G419 with Lateral acceleration senderG200, Longitudinal acceleration sender G251 Yaw rate sender G202.ABS warning lamp K47Brake system warning lamp K118S374_126Brake pressure sender 1 G201ESP and TCS warning lamp K11544ESP hydraulic circuit diagram124 2732526525268 769 10 12 11 13 14 16 1517 1819 2021 2223 24 S374_334Legend 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Reservoir Brake servo Brake pedal sensors Brake pressure sender ABS/ESP control unit Return flow pump Pressure accumulator Damping chamber Front left ABS inlet valve Front left ABS outlet valve Rear right ABS inlet valve Rear right ABS outlet valve Front right ABS inlet valve Front right ABS outlet valve 15 16 17 18 19 20 21 22 23 24 25 26 27 Rear left ABS inlet valve Rear left ABS outlet valve Front left wheel brake cylinder Front left speed sensor Front right wheel brake cylinder Front right speed sensor Rear left wheel brake cylinder Rear left speed sensor Rear right wheel brake cylinder Rear right speed sensor Switch valve High-pressure valve CAN data bus45Traction control systemsHow it works ESP has various options for stabilising the vehicle:● ●●Via specific brake intervention Via intervention in the engin