TECHNICAL DOCUMENTATION

SSP 388 4,2l V8 4V FSI

PDFEN40 pages671 KB
SSP 388 4,2l V8 4V FSI - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingSelf-study Programme 388The 4.2l V8 4V FSI EngineDesign and Function1 The 4.2l V8 4V FSI engine is a further example of direct petrol injection. It replaces the 4.2l V8 5V engine in the Touareg. Apart from the common cylinder bank angle of 90°, the two engines are no longer comparable.With output of 257 kW and 440 Nm of torque, the engine offers very good performance, outstanding dynamics and a high level of ride comfort. This engine has already been launched in the Audi Q7.S388_002This self-study programme provides information on the design and function of this new engine generation.NEWImportant NoteThe self-study programme shows the design and function of new developments. The contents will not be updated.For current testing, adjustment and repair instructions, refer to the relevant service literature.2 ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Technical features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Engine mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Chain drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Ancillary unit drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Intake system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Cylinder block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Cylinder heads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Oil supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Crankcase breather and ventilation system . . . . . . . . . . . . . . . . . . . . . . . . . 14 Cooling circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Engine management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 System overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 CAN networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Actuators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Functional diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Test yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393 IntroductionSpecial technical featuresThe 4.2l V8 4V FSI engine is the most recent example of a direct petrol injection engine from Volkswagen. It is the successor of the 4.2l V8 5V engine with intake manifold injection. In addition to direct petrol injection, certain new features have been implemented in both the engine management and in the engine's mechanical systems.S388_003Technical features● ● ● ● ● ● ● ●Bosch Motronic MED 9.1.1 Direct petrol injection Homogenous mode (Lambda 1) Double injection catalytic converter heating Electronic throttle Two hot film air mass sensors Electronically regulated cooling system Adjustment of the variable intake manifold and intake manifold flap change-over by means of an electric motor●●● ●● ●Continuous inlet and exhaust camshaft timing adjustment Two-stage magnesium variable intake manifold with integrated intake manifold flap change-over Two-piece cylinder block Flywheel-end chain drives for camshafts and ancillary units Spur gear drive for ancillary units Secondary air system4 Technical dataTorque and output diagramNmkWTorque [Nm]rpmS388_004Technical dataEngine code Type Displacement in cm³ Bore in mm Stroke in mm Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel Exhaust gas treatment Emissions standard BAR 8 cylinders with 90° V angle 4163 84.5 92.8 4 12.5:1 257 kW at 6800 rpm 440 Nm at 3500 rpm Bosch Motronic MED 9.1.1 Premium plus unleaded RON 98 or premium unleaded RON 95 4 catalytic converters, 4 lambda probes, secondary air system EU 4Power [kW]5 Engine mechanicsChain driveIn the 4.2l V8 4V FSI engine, the camshafts and ancillary units are driven via a total of four roller chains on two levels. The chain drive has the advantage that it is maintenance-free and reduces the length of the engine. The crankshaft drives the two drive gears for the camshaft timing chains via chain drive A. In turn, these two drive gears drive the camshaft adjusters for the exhaust and inlet camshafts via chain drives B and C. In chain drive D, the crankshaft drives the drive chain sprocket for ancillary drives. This is used to drive the spur gear for the ancillary units. The chains are tensioned via hydraulic spring tensioners.Camshaft adjuster for inlet camshaftChain drive ADrive chain sprocket for camshaft timing chainCamshaft adjuster for exhaust camshaftChain drive CChain drive B Guide chain sprocket for ancillary drivesSpur gear driveChain drive D S388_005CrankshaftDrive chain sprocket for ancillary drivesThe chain drive is maintenance-free and is designed for use throughout the engine's service life. In the event of repairs, please note the information in ELSA under all circumstances.6 Ancillary unit driveThe ancillary units are driven by the crankshaft via chain drive D, a spur gear drive, a gear module and four intermediate shafts. The oil pump, the coolant pump, the power steering pump and the air conditioner compressor are driven. The gear module is used to adapt the rotational speed and therefore the delivery rate of the coolant pump and the oil pump.Air conditioner compressorChain drive DCoolant pumpCrankshaftGear modulePower steering pumpOil pumpSpur gear driveDrive chain sprocket for ancillary drives S388_0067 Engine mechanicsIntake systemAs in the 4.2l V8 5V engine fitted in the Touareg, the fresh air intake system is designed with two branches, and therefore reduces pressure losses. Both intake tracts are brought together upstream of a common throttle valve module. To determine the intake mass of fresh air as accurately as possible, each intake tract is equipped with a hot film air mass meter.Air mass meter G70 Intake air temperature sender G42 cylinder bank 1Throttle valve module J338Air mass meter G246 cylinder bank 2Variable intake manifold S388_007Intake manifoldThe two-stage variable intake manifold is manufactured from die-cast magnesium. It contains the change-over flaps for the variable intake manifold and the intake manifold flaps for intake manifold flap change-over.Change-over flapIntake manifold flaps S388_0088 Variable intake manifoldIn the variable intake manifold, switching between the short and the long intake manifold is carried out depending on a performance map. - In the lower engine speed range, switching takes place to the torque position (long intake manifold) - In the upper engine speed range, switching takes place to the output position (short intake manifold) The change-over flaps are actuated by the variable intake manifold motor. If this is actuated by the engine control unit, it adjusts the selector shafts, which are connected together via a linkage system, and the change-over flaps located on these. The change-over flaps are equipped with a sealing lip, in order to ensure that the long intake manifold remains leak-tight in the torque position.Variable intake manifold motor V183Selector shaft with change-over flaps S388_009Intake manifold flap change-overThe intake manifold flaps are installed in the two intake manifold lower sections. They are actuated, depending on load and engine speed, by an intake manifold flap motor and two linkage systems. - At low load and engine speed, they are actuated and close off the lower section of the intake ports. This results in cylinder-shaped air flow into the cylinder. - At high load and engine speed, they are not actuated, and lie flush against the surface of the intake port in order to avoid flow losses. Due to emission-relevant reasons, the positions of the intake manifold flaps are monitored by two intake manifold flap potentiometers.Intake manifold flap potentiometer G336Intake manifold flapsSeparating plateIntake manifold flap potentiometer G512S388_010Intake manifold flap motor V1579 Engine mechanicsCylinder blockThe cylinder block is manufactured from an aluminium-silicon alloy by means of low-pressure gravity die casting. It is characterised by high strength, very low cylinder warming and good thermal dissipation. To obtain the narrowest cylinder webs possible, cylinder liners have been omitted. Final cylinder bore surface machining is carried out in a three-stage honing and exposure process. During this process, the aluminium is separated out from the surface and the silicon is exposed in the form of minute and particularly hard particles. These finally form the wear-resistant contact surface for the pistons and the piston rings. The ladder frame is manufactured from an aluminium-silicon alloy by means of die casting. Cast-in bearing caps manufactured from cast iron with nodular graphite reinforce the ladder frame and absorb the majority of the flow of force. Due to their thermal expansion, which is lower than that of aluminium at high temperatures, they simultaneously limit main bearing clearance. The ladder frame design with bearing caps offers high longitudinal and transverse stiffness.Cylinder blockCast-in bearing capLadder frame S388_011Crankshaft driveThe crankshaft is manufactured from high-quality tempered steel, and is supported at five points. The connecting rods are manufactured using the cracking method. The pistons are forged due to reasons of strength. The piston crown has been adapted to the combustion process involved in FSI technology, and supports the cylindrical flow of air in the cylinder. The piston skirts are coated with Ferrostan, a contact layer which contains iron. This prevents direct contact between the aluminium surfaces of the pistons and the cylinder contact surfaces, as this increases wear.Piston skirt Cracked connecting rodPiston crown Crankshaft S388_01210 Cylinder headsThe 4-valve cylinder head is manufactured from an aluminium alloy. This material guarantees very good thermal conductivity with good strength values. - The separating plates for intake manifold flap change-over are installed in the intake ports. - The injectors are fitted on the intake side in the cylinder head. - The high-pressure fuel pumps are driven via dual cams on the inlet camshafts. - The cylinder head cover is made of plastic and contains a labyrinth oil separator. - The camshafts are fully-assembled and are driven via a chain drive. - The exhaust valves are filled with sodium. This reduces the temperature at the valve by approx. 100°C.Cylinder head cover Crankcase breather systemHall senderHigh-pressure fuel pump with fuel metering valveS388_013 Fully-assembled camshaftCamshaft adjustment systemThe gas exchange processes in the engine's combustion chamber exert a significant influence on output, torque and pollutant emission. The camshaft adjustment system allows these gas exchange processes to be adapted to the engine's relevant requirements. Camshaft adjustment is carried out continuously via vane adjusters, and equates to a maximum of 42°. The position of the camshafts are detected by means of four Hall senders. When the engine is stationary, the vane adjusters are locked using a spring-loaded locking pin. The inlet camshafts are set to the "retarded" position and the exhaust camshafts to the "advanced" position. To achieve this, a return spring is installed in the exhaust camshafts' vane adjusters.Inlet adjusterS388_014Exhaust adjuster with return spring11 Engine mechanicsOil supplyDuring development of the oil supply system, great emphasis was attached to the lowest possible oil throughput. The camshaft adjusters and various friction bearings were therefore optimised. This engine's oil throughput, 50 l/ min at 7000 rpm and an oil temperature of 120°C, is very low. The advantage is that the oil remains in the oil sump for a longer period of time, and that better water and hydrocarbon (uncombusted fuel) degasification is possible. A smaller oil pump can additionally be used, as a result of which the necessary drive power and therefore the fuel consumption are reduced. A baffle plate in the area of the inlet connection ensures that no oil, which has been worked into a foam by the oil pump, is drawn into to oil system. The oil is cooled by an oil-water heat exchanger.Chain tensionerOil filter moduleCylinder bank 1Cylinder bank 2Hydraulic camshaft adjustment Oil pressure control valveOil sump upper sectionOil cooler (coolant)S388_017Oil pump (gear)Baffle plateOil sump lower section12 Oil pumpThe oil pump is located inside the oil sump upper section, and is bolted to the ladder frame. Intake is carried out via a filter on the base of the oil sump and, during vehicle operation, simultaneously via the engine's return duct. All engine lubrication points are supplied from the pressure oil side.Pressure oil sideReturn from the engineBase filter suction sideS388_019Oil filter moduleThe oil filter module is designed as a main flow filter. It is located in the innner V of the engine to facilitate maintenance. The filter element can be easily exchanged without special tools. It consists of a polymer mat.Cap Filter element consisting of polymer mat From the oil pump pressure sideTo the engine circuitS388_02013 Engine mechanicsCrankcase breather and ventilation systemCrankcase breather systemThe crankcase breather system is used to flush fresh air through the crankcase. As a result of this, water vapour and low-boiling hydrocarbons are flushed from the crankcase and the accumulation of water and uncombusted hydrocarbons in the oil is avoided. The air is removed downstream of the air filter, and is guided into the inner V of the cylinder block via a non-return valve. A restrictor downstream of the non-return valve ensures that only the defined quantity of fresh air is supplied to the crankcase.Crankcase ventilation systemVia the crankcase ventilation system, the uncombusted hydrocarbons (blow-by gases) are returned to the combustion process and do not escape into the outside air. To minimise the oil contained in the blow-by gases, they are separated via a labyrinth oil separator in the cylinder head cover and a three-stage cyclonic micro oil separator. In the cylinder head cover, the gas encounters impact plates, on which the larger oil droplets are separated. The gases are then channelled via hoses to the micro oil separator. Here, the smaller oil droplets are separated off, thereby preventing inlet valve coking. The induction point downstream of the throttle valve module is integrated into the cooling circuit to prevent it from freezing.Vent lineCooling circuit connection for heatingCrankcase breather systemS388_023Micro oil separatorPressure limiting valveNon-return valve (crankcase breather system)14 Three-stage cyclonic micro oil separatorThe quantity of uncombusted hydrocarbons and oil vapour is dependent on the engine load and speed. The micro oil is separated off via a three-stage cyclonic micro oil separator. As cyclonic oil separators only perform well in a low volumetric flow range, one, two or three cyclones are released in parallel depending on the throughput quantity of gas.Low engine load/speed – low gas throughput At low engine load and speed, the gas throughput is low. The gas flows past the control plunger into the first cyclonic oil separator. Here, the oil which is still present in the gas is pressed outwards via centrifugal force, adheres to the wall and drips into the oil collection chamber. The oil collection chamber contains an oil drain valve, which is closed via the pressure in the crankcase when the engine is running. If the engine is switched off, the valve opens and the oil which is present flows into the oil sump via a hose located below the level of the oil. The pressure control valve ensures a constant pressure level and good crankcase ventilation.Control plungerPressure control valveTo the induction point downstream of the throttle valve moduleFrom the cylinder head coverOil collection chamberOil drain valveS388_024Increasing engine load/speed – increasing gas throughput As the engine load and speed increases, so to does the mass flow of the blow-by gases. The higher the mass flow, the greater the force which acts on the control plunger. The control plunger force overcomes the spring force and releases the access ducts to further cyclones.Control plunger shiftedS388_02615 Engine mechanicsBypass valve opens – very high gas throughput The bypass valve ensures that the pressure in the crankcase does not become excessive. If the pressure in the crankcase increases rapidly, e.g. due to a jammed control plunger or piston ring flutter (may occur at high engine speeds and low load), the cyclones are no longer able to cope with this pressure increase. The pressure continues to rise and now opens the bypass valve. Part of the blow-by gases now flows past the cyclone and is guided to the intake manifold directly via the pressure control valve.Bypass valve open Gases flow past the cyclonesS388_05016 Cooling circuitThe cooling system is designed as a longitudinal cooling system. The coolant flows in on the intake side and, via the cylinder head gasket, into the head, where it flows out longitudinally via the timing chain cover. Cylinder web cooling has been improved by drilling coolant ducts with optimised cross-sections into the webs. Forced flow through these bores is ensured with the aid of specifically sealed water ducts. In addition, the engine is equipped with an electronically controlled cooling system. - In the partial load range which is not critical with regards to knocking, the coolant temperature is regulated to 105°C. In the lower partial load range, the thermodynamic advantages and reduced friction power result in a fuel saving of approx. 1.5%. - In the full load range, the coolant temperature is regulated to 90°C via the map-controlled engine cooling system thermostat. Cooler combustion chambers and better cylinder charging with reduced knocking tendency are achieved as a result.Coolant temperature sender G62 Expansion tankCirculation pump V55 Heating system heat exchangerOil coolerCoolant distributor housing with map-controlled engine cooling system thermostat F265 Alternator Coolant pump Coolant temperature sender G83 S388_016 Radiator17 Engine mechanicsFuel systemThe fuel system is a requirement-controlled fuel system. This means that both the electronic fuel pump and the two high-pressure fuel pumps only deliver the amount of fuel required by the engine at that particular moment. As a result of this, electrical and mechanical power requirements are reduced and fuel consumption is lowered.The fuel system is sub-divided into a low-pressure and a high-pressure fuel system. - The fuel pressure of up to 7 bar in the low-pressure fuel system is generated by an electronic fuel pump, which is actuated by the engine control unit via a fuel pump control unit. - The fuel pressure of 25 to 105 bar in the high-pressure fuel system is generated by two mechanical high-pressure fuel pumps, each of which is driven via a dual cam by the inlet camshafts. To minimise fuel pressure pulsations, both high-pressure fuel pumps deliver fuel into a common fuel line to the fuel rails. In addition, this high-pressure delivery has been chosen in such a way that both pumps' delivery into the high-pressure area is offset.High-pressure fuel pump with fuel metering valve N290Injectors, cylinders 1-4 N30-N33Fuel pressure sender, high pressure G247Fuel railHigh-pressure fuel pump with fuel metering valve 2 N402Pressure limiting valve (120 bar) Injectors, cylinders 5-8 N83-N86 Fuel pressure sender for low pressure G410Fuel filter integrated into tankLeakage lineS388_027 Fuel tank18 Exhaust systemThe exhaust system is a twin-branch design. This means that each cylinder block has a separate exhaust tract. The exhaust manifolds are insulated sheet metal manifolds with a gas-tight inner shell. This air-gap insulation enables a compact design and fast heating. Additional heat shield measures are no longer necessary. The exhaust manifolds are secured to the cylinder heads using clamping flange technology. Two broadband lambda probes are installed downstream of the exhaust manifolds and two transient lambda probes downstream of the starter catalytic converters. The starter and main catalytic converters' substrate material is comprised of ceramic. Both exhaust tracts end in the front silencer. There, the sound waves overlap and noise emissions decrease. Two exhaust pipes lead from the front silencer to the rear silencer. Both exhaust pipes are routed separately in the interior of the rear silencer. The front and rear silencers function as absorption silencers. The exhaust gas flows into the outside air via two tailpipes.Exhaust manifold with air-gap insulation Broadband lambda probe G39 Transient lambda probe G130Broadband lambda probe G108 Starter catalytic converters Transient lambda probe G131 Main catalytic convertersFront silencerRear silencerS388_02819 Engine mechanicsSecondary air systemTo heat the catalytic converters as quickly as possible, the mixture is enriched with fuel on cold-starting and during warming up. This results in a higher percentage of uncombusted hydrocarbons in the exhaust gas during this period. Thanks to air injection downstream of the exhaust valves, the exhaust gases are enriched with oxygen, leading to oxidation (afterburning) of the hydrocarbons and the carbon monoxide. The heat released during this process also heats the catalytic converter, helping it to reach its operating temperature faster. The secondary air system is comprised of: - the secondary air pump relay J299, - the secondary air pump motor V101 and - two self-opening combination valves Input signals - Signal from the lambda probes (for system diagnosis) - Coolant temperature - Air mass meter engine load signalsConnection on the air filterSecondary air pumpS388_029 Combination valves (self-opening)20 Secondary air injectionThe secondary air system is switched on during cold-starting, at the start of the warm-up phase and for test purposes as part of EOBD. In this case, the engine control unit actuates the secondary air pump via the secondary air pump relay. When the pressure which has been generated is present at the combination valves, they open and the air flows downstream of the exhaust valves. Afterburning takes place.Function of the combination valvesThe combination valves are self-opening valves. This means that they are opened via the pressure generated by the secondary air pump, and not via vacuum as in the previous secondary air systems.Combination valve closedThe pressure in the combination valves corresponds to ambient pressure. The valves are closed.From theSpringDiaphragmsecondary air pumpValve stem hollowed out Valve disk closedExhaust gas sideS388_015Combination valve openIf the current for the secondary air pump is activated via the relay, it begins to deliver air. Pressure builds up due to the fact that the combination valve is closed. This is present at the valve disk and, via the hollowed-out valve stem, at the diaphragm. If a pressure of approx. 450 mbar above ambient pressure acts on the diaphragm and the valve disk, the valve opens. The air delivered by the secondary air pump now flows downstream of the exhaust valves and afterburning takes place.From the secondary air pumpDiaphragmValve disk openTo the exhaust valvesS388_05721 Engine managementSystem overviewSensorsAir mass meter G70, G246 Intake air temperature sender G42 Engine speed sender G28 Accelerator position sender G79 and G185Hall sender G40, G163, G300, G301 Throttle valve module J338 Angle sender for throttle valve drive G187, G188 Intake manifold flap potentiometer G336, G512Fuel pressure sender for low pressure G410Engine control unit J623Fuel pressure sender for high pressure G247Coolant temperature sender G62 CAN drive data busRadiator outlet coolant temperature sender G83Knock sensors G61, G66, G198, G199Lambda probe G39, G108 Lambda probe after catalytic converter G130, G131 Brake light switch F Brake pedal switch F47 Brake servo pressure sensor G294Additional input signals22 ActuatorsMotronic current supply relay J271 Fuel pump control unit J538 Fuel pump G6 Fuel metering valve N290, N402 Injectors for cylinders 1 - 8 N30-33, N83-N86 Active charcoal filter system solenoid valve N80 Throttle valve module J338 Throttle valve drive for electric throttle G186 Intake manifold flap motor V157 Variable intake manifold motor V183 Inlet camshaft control valves N205, N208Exhaust camshaft control valves N318, N319 Ignition coil 1 - 8 with output stage N70, N127, N291, N292, N323-N326 Map-controlled engine cooling system thermostat F265 Continued coolant circulation relay J151 Circulation pump V55 Lambda probe heater Z19, Z28 Lambda probe heater after catalytic converter Z29, Z30 Secondary air pump relay J299 Secondary air pump motor V101 Radiator fan control unit J293 Radiator fan V7 Radiator fan control unit 2 J671 Radiator fan V177 Brake servo relay J569 Vacuum pump for brakes V192S388_030Additional output signals23 Engine managementCAN networkingThe diagram below shows the control units with which the engine control unit J623 communicates via the CAN data bus and exchanges data.J285J428J533 T16J623J217J644CAN drive data busJ104J197J518CAN convenience data busJ234J646J519G85 J255 J527S388_031G85 J104 J197 J217 J234 J255 J285 J428 J518Steering angle sender ABS control unit Adaptive suspension control unit Automatic gearbox control unit Airbag control unit Climatronic control unit Control unit with display in dash panel insert Adaptive cruise control unit Entry and start authorisation control unitJ519 J527 J533 J623 J644 J646 T16Onboard supply control unit Steering column electronics control unit Data bus diagnostic interface Engine control unit Energy management control unit Transfer box control unit Diagnosis connector24 SensorsHot film air mass meter G70 with intake air temperature sender G42 and hot film air mass meter 2 G246To minimise pressure losses, the intake tract has a twin-branch design. The most accurate possible air mass signal is achieved by two hot film air mass meters. Hot film air mass meter G70 is installed along with intake air temperature sender G42 in the intake tract on the cylinder bank 1 side. Hot film air mass meter G246 is installed in the intake tract on the cylinder bank 2 side. From the signals transmitted by the two air mass meters and the intake air temperature sender, the engine control unit calculates the mass and the temperature of the intaken air respectively.Hot film air mass meter G70 with intake air temperature sender G42 cylinder bank 1Hot film air mass meter G246 cylinder bank 2S388_032Signal use The signals are used to calculate all load- and engine speed-dependent functions. These include the injection period, ignition timing or camshaft adjustment, for example.Effects in the event of failure If one or both air mass meters fail, the throttle valve position and the engine speed are used as correction values. If the intake air temperature sender fails, a fixed, substitute value is assumed.25 Engine managementHall sender G40, G163, G300, G301Hall senders G40 and G300 are located on cylinder bank 1 and Hall senders G163 and G301 are located on cylinder bank 2. By scanning a quick-start sender wheel, the engine control unit recognises the position of each cylinder bank's inlet and exhaust camshafts.Hall sender G40Cylinder bank 1 Hall sender G40 - inlet camshaft Hall sender G300 - exhaust camshaft Cylinder bank 2 Hall sender G163 - inlet camshaft Hall sender G301 - exhaust camshaftHall sender G300S388_033Signal use The signals are used to detect the first cylinder, for camshaft adjustment, and to calculate the injection point and the ignition timing.Hall sender G163Effects in the event of signal failure No further camshaft adjustment takes place if a Hall sender fails. The engine continues to run and also re-starts again after switching off thanks to run-on recognition. Torque and power are reduced at the same time.S388_034 Hall sender G30126 Fuel pressure sender for low pressure G410The sender is installed in the supply line to the two high-pressure fuel pumps. It measures the fuel pressure in the low-pressure fuel system and transmits a signal to the engine control unit.Fuel pressure sender for low pressure G410S388_035Signal use The signal is used by the engine control unit to regulate the low-pressure fuel system. Following the sender signal, the engine control unit transmits a signal to the fuel pump control unit J538, which then regulates the electronic fuel pump G6 as required.Effects in the event of signal failure If the fuel pressure sender fails, the fuel pressure is regulated by a fuel pressure pilot control system. The fuel pressure is then approx. 6.5 bar.27 Engine managementFuel pressure sender, high pressure G247The sender is located in the inner V of the cylinder block, and is connected to the fuel rail via a line. It measures the fuel pressure in the high-pressure fuel system and transmits the signal to the engine control unit.Signal use The engine control unit evaluates the signals and regulates the pressure in the fuel rail pipes via the two fuel metering valves.Fuel railS388_036 Fuel pressure sender, high pressure G247Effects in the event of signal failure If the fuel pressure sender fails, no further high fuel pressure is built up. The engine runs in emergency mode with low fuel pressure. Power and torque are reduced.28 Intake manifold flap potentiometer G336 and G512The two intake manifold flap potentiometers are secured to the intake manifold and are connected to the shaft for the intake manifold flaps. They recognise the position of the intake manifold flaps.Signal use The position is important, as intake manifold change-over affects air flow in the combustion chamber and the inlet air mass. The position of the intake manifold flaps is therefore relevant to the exhaust gas, and must be checked via self-diagnosis.S388_037 Potentiometer for intake manifold flap G336 Potentiometer for intake manifold flap G512Effects in the event of signal failure If the signal from the potentiometer fails, the position of the intake manifold flaps at the time of failure and the relevant ignition timing are used as substitute values. Power and torque are reduced and fuel consumption increases.29 Engine managementActuatorsFuel pump G6The electronic fuel pump and the fuel filter are combined to form a fuel delivery unit. The fuel delivery unit is located in the fuel tank.Task The electronic fuel pump delivers the fuel in the lowpressure fuel system to the high-pressure fuel pump. It is actuated with a PWM signal by the fuel pump control unit. The electronic fuel pump always supplies the quantity of fuel required by the engine at the present moment in time.S388_038 Fuel pump G6Effects in the event of failure If the electronic fuel pump fails, engine operation is no longer possible.Fuel pump control unit J538The fuel pump control unit is mounted under the rear seat bench in the cover for the electronic fuel pump.Task The fuel pump control unit receives a signal from the engine control unit and controls the electronic fuel pump with a PWM signal (pulse-width modulation). It regulates the pressure in the low-pressure fuel system between 5 and 7 bar.S388_039 Fuel pump control unit J538Effects in the event of signal failure If the fuel pump control unit fails, engine operation is not possible.30 Fuel metering valve N290 and N402The fuel metering valves are located at the sides of the high-pressure fuel pumps.Fuel metering valve N402Task They have the task of making the required quantity of fuel available at the required fuel pressure in the fuel rail pipe.Effects in the event of signal failure The regulating valve is open when currentless. This means that high pressure is not built-up and the engine is run with the existing fuel pressure from the electronic fuel pump. As a result of this, output and torque are significantly reduced.Fuel metering valve N290S388_04031 Engine managementInlet camshaft control valve 1 and 2 N205 and N208 Exhaust camshaft control valve 1 and 2 N318 and N319These solenoid valves are secured to the cylinder head covers.Inlet camshaft control valve 1 N205Task Depending on actuation by the engine control unit, they distribute the oil pressure to the camshaft adjusters according to the adjustment direction and adjustment travel. Both camshafts are infinitely adjustable: - Inlet camshaft 42° crank angle - Exhaust camshaft 42° crank angle - Maximum valve overlap angle 47° crank angle When no oil pressure is available (engine switched off), the exhaust camshaft is mechanically locked.Inlet camshaft control valve 2 N208Exhaust camshaft control valve 1 N318S388_041Effects in the event of signal failure If an electrical cable to the camshaft adjusters is defective or a camshaft adjuster fails due to mechanical jamming or insufficient oil pressure, no further camshaft adjustment is carried out. Power and torque are reduced.Exhaust camshaft control valve 2 N319S388_04232 Variable intake manifold motor V183The variable intake manifold motor is bolted to the intake manifold.Variable intake manifold motor V183Task The motor is actuated by the engine control unit depending on engine load and speed. The motor actuates the change-over flaps via a shaft and switches to the torque or the output position.Effects in the event of failure If the variable intake manifold motor fails, intake manifold change-over is no longer possible. The intake manifold remains in the position in which theS388_043change-over flaps were located at the time of failure. Power and torque are reduced.Intake manifold flap motor V157The intake manifold flap motor is bolted to the variable intake manifold. Task The motor is actuated by the engine control unit depending on engine load and speed. Via two operating rods, it thereby adjusts four intake manifold flaps per cylinder bank. If these are actuated, they close part of the intake port in the cylinder head. This leads to cylindrical air movement in the cylinder head and improves mixture formation.Intake manifold flap motor V157S388_044Effects in the event of failure If the intake manifold motor fails, the intake manifold flaps can no longer be actuated. This leads to a deterioration in combustion and a reduction in output and torque. The fuel consumption also increases.33 Functional diagramJ27130 15 87aS S G6 J285J285 S S J285 J538GG169N30N86N83N84N33N32J623A N70N85N31N326N324N323N292N325N291N127G79 P Q P Q P Q P Q P Q P Q P Q P QG18531A G G6 G79 G169 G185 J271 J285 J538 J623 N30N33Battery Fuel gauge sender Fuel pump Accelerator position sender Fuel gauge sender 2 Accelerator position sender 2 Motronic current supply relay Control unit with display in dash panel insert Fuel pump control unit Engine control unit Injector, cylinder 1 to Injector, cylinder 4N70 N83N86 N127 N291N292 N323N326 P Q SIgnition coil 1 with output stage Injector, cylinder 5 to Injector, cylinder 8 Ignition coil 2 with output stage Ignition coil 3 with output stage Ignition coil 4 with output stage Ignition coil 5 with output stage to Ignition coil 8 with output stage Spark plug connector Spark plugs Fuse34 J757S G39/Z19S G108/Z28S G130/Z29 G131/Z30N290N402J623J338 G186 G187 G188 G61 G66 G198 G199 G28 G163S388_045G28 G39 G61 G66 G108 G130 G131 G163 G186 G187 G188 G198 G199 J338 J623 J757 N290 N402Engine speed sender Lambda probe Knock sensor 1 Knock sensor 2 Lambda probe 2 Lambda probe after catalytic converter Lambda probe 2 after catalytic converter Hall sender 2 Throttle valve drive Throttle valve drive angle sender Throttle valve drive angle sender Knock sensor 3 Knock sensor 4 Throttle valve module Engine control unit Engine component current supply relay Fuel metering valve Fuel metering valve 2S Z19 Z28 Z29 Z30Fuse Lambda probe heater Lambda probe 2 heater Lambda probe 1 heater after catalytic converter Lambda probe 2 heater after catalytic converterPositive Earth Input signal Output signal Bi-directional cable CAN data bus35 Functional diagramJ151SSSSN208N205N318N319V157V183V7J293V177J671AJ623G163G40G336G512G247G62G300G301S388_045A F265 G40 G62 G163 G247 G300 G301 G336 G512 J151Battery Map-controlled engine cooling system thermostat Hall sender Coolant temperature sender Hall sender 2 Fuel pressure sender, high pressure Hall sender 3 Hall sender 4 Intake manifold flap potentiometer Intake manifold flap potentiometer 2 Continued coolant circulation relayJ293 J623 J671 N205 N208 N318 N319 S V7 V157 V177 V183Radiator fan control unit Engine control unit Radiator fan control unit 2 Inlet camshaft control valve 1 Inlet camshaft control valve 2 Exhaust camshaft control valve 1 Exhaust camshaft control valve 2 Fuse Radiator fan Intake manifold flap motor Radiator fan 2 Variable intake manifold motor36F265 J708J569 BJ299SJ255SSS V55 V192 V101SF47F J508J623m G410 G83 G294 G70 G42 G246 B N80123 K1 2 3Reversing light switch CAN data bus CAN data busS388_045Starter Brake light switch Brake pedal switch Intake air temperature sender Air mass meter Radiator outlet coolant temperature sender G246 Air mass meter 2 G294 Brake servo pressure sensor G410 Fuel pressure sender for low pressure K Dash panel insert J255 Climatronic control unit J299 Secondary air pump relay J508 Brake light suppression relay J569 Brake servo relay J623 Engine control unit J708 Residual heat relay N80 Active charcoal filter system solenoid valve 1 S Fuse V55 Circulation pump B F F47 G42 G70 G83V101 V192Secondary air pump motor Vacuum pump for brakesPositive Earth Input signal Output signal Bi-directional cable CAN data bus37 ServiceSpecial toolsDesignation Thrust piece T 40051 Tool Application For installing A/C compressor drive sealing ring.Thrust piece T40052For installing power steering pump drive sealing ring.Camshaft clamps T40070For locking camshafts on cylinder bank 1 and cylinder bank 2.Locking pins T40071For locking chain tensioners for chain drives A, B, C, D.Key T40079For pre-tensioning inlet and exhaust camshafts after installing the camshaft timing chain.Locating pins T40116For locating the ladder frame on attachment to the cylinder head.38 Test yourselfWhich answer is correct? One or several of the answers which are provided may be correct. 1. How are the camshafts driven? a) Via a toothed belt drive. b) Via an individual roller chain from the crankshaft. c) From the crankshaft, a roller chain drives two drive chain sprockets for the camshaft timing chains. In turn, these drive the camshafts via one chain each.2. How is intake manifold change-over carried out? a) Intake manifold change-over is carried out via a vacuum unit. b) Intake manifold change-over is carried out via a variable intake manifold electric motor. c) Intake manifold change-over is carried out via a Bowden cable.3. Which statement on the high-pressure fuel pumps is correct? a) Each of the two high-pressure fuel pumps delivers to one cylinder bank. b) Both high-pressure fuel pumps deliver the fuel jointly to both fuel rails. c) One or both high-pressure fuel pumps deliver fuel depending on engine load and speed.4. Which statement on the cooling system is correct? a) It is an electronically controlled cooling system with a thermostat for map-controlled engine cooling. b) It is a dual-circuit system with different cooling temperatures in the cylinder block and cylinder head. c) It is an unregulated system with constant coolant temperatures.Answers 1. c 2. b 3. b 4. a39 388© VOLKSWAGEN AG, Wolfsburg All rights and rights to make technical alterations reserved. 000.2811.83.20 Technical status 05.2007 Volkswagen AG Service Training VSQ-1 Brieffach 1995 D-38436 WolfsburgThis paper has been manufactured from pulp bleached without the use of chlorine.