TECHNICAL DOCUMENTATION
SSP 400 The Golf Variant 2007

This PDF is currently unavailable.
Read document text
Service TrainingSelf-study Programme 400The Golf Variant 2007The Golf Variant 2007 – design and variabilityThe Golf Variant 2007 continues the success story of its predecessor models. In particular, it impresses with its dynamic design, which is characterised by its sporty, dynamic appearance, its innovative exterior, a new rear light design and its typical Golf face.S400_003S400_002In terms of product characteristics, the Golf Variant 2007 sets the standards in its class, e.g. as regards:● ● ● ●safety, design, e.g. the new rear light design, quality, handling,● ● ● ●the amount of space on offer, variability, payload and load securing, vehicle dynamics and the new panoramic sliding sunroof.Separate self-study programmes are available on the following current topics:● ●Self-study programme 390 Self-study programme 405The 7-speed Double-clutch Gearbox 0AM The 1.4l 90 kW TSI Engine with TurbochargerThis self-study programme has been created in co-operation with Volkswagen de México erstellt.NEWImportant NoteThe self-study programme shows the design and function of new developments. The contents will not be updated.For current testing, adjustment and repair instructions, refer to the relevant service literature.2ContentsIn brief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Occupant protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Engines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Power transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Running gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Electrical system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Heating and air conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Radio, telephone and navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543In briefWhere will the Golf Variant be produced?The Golf Variant will be produced in Volkswagen's Puebla plant in Mexico.S400_031S400_032The Puebla plantThis plant started operation in 1964 and produced the Beetle. Around 14,000 staff are currently employed in Puebla; amongst other vehicles, they produce the New Beetle and the Jetta. These will now also be joined by the new Golf Variant. In certain markets, this vehicle will also be marketed under the name Jetta Variant.S400_0804… Modern clocked assembly lines …S400_045S400_030... Modular production …With its high standard of quality, the ultra-modern Puebla plant is one of Volkswagen AG's leading production plants. The Golf Variant 2007 will be built on the production lines which are already in place for the Jetta in Mexico.S400_0855In briefThe Golf Variant 2007In many disciplines, the Golf Variant 2007 again sets the standards in its class, e.g.: Safety Design Quality Handling Ride comfort Spaciousness Multifunctionality●●Load compartment concept with extensive storage compartments and securing optionsComfortable spatial availability thanks to the extended passenger compartment●Modern, high-quality interior●Front seats with optional 4-way lumbar support (with integrated height adjustment)●Modern illumination concept for the interior lighting●Electromechanical power steering6●Optional panoramic sliding sunroof●High body stiffness●New aerial concept●New rear light designS400_052●Optional sports running gear●Optimised front and rear axle (four-link suspension)●Increased front and rear track width ensures significantly better vehicle dynamics●2C-Climatronic (2-zone climate control)7In briefTechnical dataGolf Variant 2007S400_063S400_064S400_065 The dimensions given in the pictures are in mm.Length Width Height with roof rails Wheelbase Roof load Braked towing capacity up to a gradient of 8%4556 mm 1781 mm 1504 mm 2578 mm 75 kg 1500 1700 kg*Track width at front Track width at rear Curb weight Permissible gross vehicle weight Tank capacity Drag coefficient1535 mm 1508 mm 1278 - 1414 kg* 1800 kg 55 litres 0.31 Cd8Passenger compartment dimensionsS400_068S400_069S400_070The dimensions given in the pictures are in mm.Front headroom Rear headroom Luggage compartment aperture Through loading width972 mm 969 mmHeight of load sill570 mm 505 litres**Luggage compartment volume 801 mm 1014 mm 560 litres**** Depending on engine ** Without variable load floor *** With variable load floor9BodyBody structureThe basic characteristics of the Golf Variant's body are based on the Jetta body.Laser welding technologyThe laser welding concept familiar from the Jetta will be successfully continued in the Golf Variant for the variant-specific components in the rear area. In addition to the advantages already described for the Jetta, a significantly stiffer rear end is achieved due to laser welding. This makes a vital contribution to the stiffness of the vehicle as a whole.Static and dynamic stiffnessThe Golf Variant sets standards in terms of static and dynamic stiffness. Its static stiffness is around 39% greater than that of its predecessor. Dynamic stiffness has been increased as follows:● ●16% in torsion 32% in flexion10S400_051Legend Red = Yellow = Blue = side crash area passenger compartment frame structureFurther information on the body can be found in self-study programme No. 354 "The Jetta 2006".11BodyFeaturesIn the front area of the body, approximately up to the B-pillar, the Golf Variant takes equipment elements from the Jetta.DoorsThe front doors have the door concept familiar from the Jetta. The design of the rear doors is conventional, using an assembly carrier.Front seatsThe front seats in the Golf Variant can be adjusted either mechanically or electrically. A front passenger seat with through-loading function is optionally available.Rear lightsIn the Golf Variant, the rear lights are not split, and are integrated into the relevant, rear body side panel. Thanks to the lights, which project into the side panel, visibility to the rear and also to the side is extensively improved.12Rear seat benchThe rear seat bench is split 60 : 40 and can be folded.Rear side windowsThe aerials for radio reception are integrated into the rear side windows.TailgateThe tailgate gives access to a large load compartment aperture. It is opened manually, whilst raising is supported by gas-filled struts.S400_050Load compartmentThe luggage compartment, which is larger than that of the predecessor, can be put to multiple uses. This is achieved by the storage compartments in the optionally available, variable load floor, the securing options and the folding concept for the rear seat bench.13BodyPanoramic sliding sunroofThe Golf Variant can be optionally equipped with panoramic sliding sunroof. The panoramic sliding sunroof can be opened to a maximum length of 660 mm. In comparison with conventional sliding sunroofs, it offers the advantage that more light enters into the vehicle's passenger compartment. The panoramic sliding sunroof offers a sense of space comparable with that of a convertible, but with less draught. Unlike in a convertible, the fact that the occupants are better enclosed within the body increases significantly better accident protection.Panoramic sliding sunroof – glass panel 1 slid completely to the rear Sunroof roller blind – semi-extendedS400_107 Wind deflector – fully raisedThe panoramic sliding sunroof is a large glass roof consisting of two glass panels. It is bolted to a reinforcement frame in the body's roof structure. The seal between the panoramic sliding sunroof and the body is achieved by means of a gasket on the body side. The special feature of the panoramic sliding sunroof is guidance of the front panel over the rear, fixed glass panel into the sliding position. The glass panel is raised and moved via electrically driven Bowden cables. To protect against excess sunlight, the panoramic sliding sunroof is equipped with an electrically driven sunroof roller blind. The panoramic sliding sunroof is also equipped with an extending wind deflector.14Components (exploded diagram)Glass panel 2, fixed Roof cut-out gasket Glass panel 1, movableWind deflector Sunroof roller blind mounting, sunroof roller blind retractedRight-hand mechanismLeft-hand mechanismRight Bowden cable for opening and closing glass panel 1 Left Bowden cable for opening and closing glass panel 1 Mounting frameElectric drive, sunroof roller blindS400_072Electrical connection cable Electric drive, panoramic sliding sunroof15BodyAdjustment of glass panel 1Glass panel 1 is moved to the relevant position via a mechanism in the panoramic sliding sunroof. The mechanism is driven via an electric motor by means of a Bowden cable attached on both the left and righthand sides. The Bowden cables move the mechanism within an adjustment range; the relevant roof positions can be reached in this way. By means of the front end pieces with separate guide plate tracks and the relevant slides, glass panel 1 is clearly positioned in the front area.Position of the mechanism Roof vent positionClosed positionS400_116 Guide plate Pin Vent position S400_113Bowden cableS400_117 Guide plate movementAt the start of the tilting movement, the rear section of the roof is raised via a guide plate and pins which run in this. The roof moves to the vent position.Position of the mechanism Roof sliding positionSliding positionPinS400_118 Guide plate movement Guide plateGuide plate track Slide End pieceS400_114If the Bowden cable continues to be moved, starting from the vent position, the front section of the mechanism is also raised and glass panel 1 is moved to the sliding position.This is also carried out by means of a guide plate and pins running in it. The slide runs towards the separate end piece and guide plate track. Glass panel 1 can then be moved backwards over fixed glass panel 2. When closing, the process runs in reverse order.16OperationThe panoramic sliding sunroof and the sunroof roller blind are operated via a common switch in the display in the front area of the roof lining. This switch has three functions and adjustment options:●Display in the roof lining Switch for panoramic sliding sunroof●●Turning the switch to move glass panel 1 to the sliding position Pressing the switch to move glass panel 1 to the vent position Short or long push on the sunroof roller blind buttons (one-touch or jog mode) to move the sunroof roller blindS400_084Rotating ring Open, press switch press function for vent positionEmergency actuationIf the situation necessitates, glass panel 1 or the sunroof roller blind can be closed after blocking by constantly pulling on the switch or via jog mode. To do this, the rotating ring must be in the "sliding sunroof closed" position. Glass panel 1 is then closed without closing force limitation.Close, pull switch pull function for zero position and emergency closing S400_081Emergency adjustmentSunroof roller blind button "open"If the panoramic sliding sunroof can no longer be adjusted electrically, closing can alternatively be carried out via mechanical emergency adjustment using a tool (Allen key, 4 mm). As a result of mechanical emergency adjustment, all values (pre-selection positions, protection ranges and partial trapping force limit value increases) are "erased". Malfunctions such as, e.g. closing force limitation triggering, may therefore occur when glass panel 1 is next adjusted. Following emergency adjustment, a workshop visit is therefore vital to re-adjust the panoramic sliding sunroof.Sunroof roller blind button "close" Roof completely open, end of sliding position Comfort position, sliding position Positions for open roof, sliding positionS400_082 Roof slightly open, wind deflector extended, sliding position Roof closed, zero position17BodyRaising glass panel 1 to the vent positionWhen raising glass panel 1 to the vent position, the following situations are possible:●●In rotating ring position "roof closed", pressing the switch raises glass panel 1 to the vent position. Glass panel 1 can be closed by pulling on the switch; it moves back to the zero position.Open, press switch press function for vent positionClose, pull switch pull function for zero position and emergency closing S400_108 Switch display in rotating ring position "roof closed" on use of the press and pull functionAutomatic operation = actuate switch briefly Manual operation = actuate switch for a longer timeEmergency actuation If the situation necessitates, glass panel 1 can be closed after stopping by constantly pulling on the switch. Glass panel 1 is then closed without closing force limitation.Glass panel 1 raised to vent positionGlass panel 2 fixedS400_074Glass panel 1 raised to vent position, vent positionSunroof roller blind closedS400_10118Opening glass panel 1●Roof completely open, end of sliding position●●●To move glass panel 1 backwards over glass panel 2 to the sliding position, the rotating ring on the switch must be turned clockwise from the zero position. In this case, the panoramic sliding sunroof is opened to different lengths depending on the setting position. From the first position for sliding position, the wind deflector is raised. The panoramic sliding sunroof has a comfort position; this is separately identified by a mark. The length to which the roof is opened in the comfort position ensures that wind noise is extensively avoided during driving. The rotating ring no longer engages at the end of the sliding position. To open the roof completely, the rotating ring must be rotated to the end in the direction of rotation and must be held until the roof is open.Comfort positionSliding position, five positions for open roofSliding position, roof slightly open, wind deflector extendedS400_109Roof closed, zero positionEmergency actuation If the situation necessitates, glass panel 1 can be closed after stopping by constantly pulling on the switch. Glass panel 1 is then closed without closing force limitation.Sunroof roller blind closed Wind deflector raisedGlass panel 1 completely openS400_075 Glass panel 1 completely open, end of sliding positionSunroof roller blind closedS400_10219BodyClosing glass panel 1When closing glass panel 1, the following situations are possible:●Close, pull switch pull function for zero position and emergency closing Roof completely open, end of sliding position Comfort position●To move glass panel 1 forwards from the sliding position to the zero position and therefore close the panoramic sliding sunroof, the rotating ring on the switch must be rotated from its present position, counter clockwise, to the rotating ring position "roof closed". The panoramic sliding sunroof closes automatically. To move glass panel 1 downwards from the vent position to the zero position and therefore close the panoramic sliding sunroof, the switch must be pulled down (pull function – see "Raising glass panel 1 to the vent position"). The panoramic sliding sunroof closes automatically.Sliding position, five positions for open roofSliding position, roof slightly open, wind deflector extended Roof closed, zero positionS400_110Switch display in rotating ring position "roof closed" on use of the push and pull functionEmergency actuation If the situation necessitates, glass panel 1 can be closed after stopping by constantly pulling on the switch. Glass panel 1 is then closed without closing force limitation.Glass panel 1 closedGlass panel 2 fixedS400_073 Sunroof roller blind openGlass panel 1 closed, zero positionS400_10020Opening and closing the sunroof roller blindThe panoramic sliding sunroof is supplemented by an electrically driven sunroof roller blind, which is installed in the rear area of the panoramic sliding sunroof. The roller blind can be opened or closed by pressing the buttons within the switch. In this case, it is electrically extended or retracted beneath the two glass panels in the assembly frame guides.. The sunroof roller blind can be actuated regardless of the position of glass panel 1.Open sunroof roller blind - sunroof roller blind button "open"S400_111Close sunroof roller blind sunroof roller blind button "close"Automatic operation = actuate sunroof roller blind button briefly Manual operation = actuate sunroof roller blind button for a longer time For the possible sunroof roller blind operating variants, please refer to the owner's manual.Emergency actuation If the situation necessitates, and the sunroof roller blind fails to close due to mechanical sluggishness, it can be closed via jog mode. The sunroof roller blind is then closed without closing force limitation.Sunroof roller blind half openGlass panel 1 completely openS400_099Sunroof roller blind half openGlass panel 1 completely open, end of sliding positionS400_10321BodyAutomatic and manual adjustment of the panoramic sliding sunroof and the sunroof roller blindThe panoramic sliding sunroof and the sunroof roller blind are operated via a common operating unit. This contains button 1 for tilting roof E582, button 1 for sunroof roller blind E584 and sliding sunroof adjustment regulator E139. All control information is read in and processed directly by sliding sunroof adjustment control unit J245. Sliding sunroof adjustment control unit J245 is integrated into the LIN data bus and controls the opening and closing of the panoramic sliding sunroof. Sliding sunroof motor V1 is also integrated into sliding sunroof adjustment control unit J245. Sunroof roller blind control unit J394 is also integrated into the LIN data bus and controls the opening and closing of the sunroof roller blind. Sunroof roller blind motor V260 is also integrated into sunroof roller blind control unit J394.Via onboard supply control unit 2 J520, which is integrated into data bus diagnostic interface J533, the information from other control units is also read in:●The driver door control unit J386 evaluates the information from driver side central locking lock unit F220 and actuation of the central locking system button on the driver side. The driver door control unit J386 evaluates the information from front passenger side central locking lock unit F221 and actuation of the central locking system button on the front passenger side. The convenience system central control unit J393 evaluates the opening of the driver or front passenger door after switching off the ignition. If these are not opened after switching off the ignition, a power-down time of ten minutes runs (high release signal). Ten minutes after switching off the ignition, release for the panoramic sliding sunroof should be widhdrawn via a request from the driver door control unit J386 and front passenger door control unit J387 to the convenience system central control unit J393 (low release signal). If, in the event of a fault, release for the panoramic sliding sunroof is not withdrawn after ten minutes, the drive for the panoramic sliding sunfoof and the sunroof roller blind is switched to sleep mode by the onboard supply control unit J519 after a further 25 minutes. Release for the panoramic sliding sunroof and the sunroof roller blind is withdrawn if the ignition is switched off and the driver or front passenger door is opened. The relevant behaviour of the panoramic sliding sunroof and the sunroof roller blind can be coded in the convenience system central control unit J393 and onboard supply control unit 2 J520. The ABS control unit J104 reports the speed. Closing force limitation can therefore be reduced at high speeds. The onboard supply control unit J519 ensures that terminals 15 and X are enabled.●●●●22Functional diagram (panoramic sliding sunroof) Legend E139 E582 E584 F220 F221 J104 J245 J386 J387 J393 J394 J519 J520 J533 V1 V260 Sliding sunroof adjustment regulator Button 1 for tilting roof Button 1 for roof roller blind Driver side central locking lock unit Front passenger side central locking lock unit ABS control unit Sliding sunroof adjustment control unit Driver door control unit Front passenger door control unit Convenience system central control unit Sunroof roller blind control unit Onboard supply control unit Onboard supply control unit 2 Data bus diagnostic interface Sliding sunroof motor Sunroof roller blind motorCAN drive data busS400_090CAN convenience data bus Thermal protection: Hall sensors for speed and travel detection are integrated into the panoramic sliding sunroof drive. Thermal protection can be calculated from these and with the voltage supply values. The purpose is to achieve misuse protection (play protection). CAN instrument cluster data bus CAN data bus line LIN data bus line Input Output23BodyDoor conceptThe door concept already familiar from the Jetta is used for the front doors in the Golf Variant. The design of the rear doors is conventional, using an assembly carrier.Front doorsThe front doors consist of an outer door panel with two retaining rails and an inner door panel for mounting the component parts. The outer door panel is bonded to the retaining rails. The retaining rails are bolted to the inner door section.Inner door panel Cover stripRetaining railCover stripOuter door panel Side impact bar S400_049Retaining rail24Rear doorsThe rear doors consist of an outer door panel and an inner door panel. The door components are integrated into an assembly carrier, which is bolted to the inner door panel.The outer door panel is flanged around and bonded to the inner door panel.AdhesiveOuter door panelInner door panel S400_048 S400_046 Assembly carrier Inner door panelA side impact bar is also installed in the door. It is bolted to the inner door panel in the lower area of the door.Inner door panelS400_047 Side impact bar25BodyStorage compartment conceptThe interior of the Golf Variant 2007 is characterised by a multitude of storage compartments and securing options.●2 cup holders and 2 storage compartments in the centre console (optional: smoker package) 2 cup holders in the rear centre armrest●Storage compartments in the front doors, including bottle holder (for max. 1l bottle)●In addition to the hook on the grab handle, a coat hook is fitted as standard on the B-pillar trim. The hook is positioned in such a way that a jacket or a coat does not impede visibility through the side window.●Optional pockets on the rear of the front seat backrests26●Small roof console with storage compartment in the solid roof●Glove box in the instrument panel, which is cooled in combination with an air conditioner●Depending on equipment variant, a normal and a cooled storage compartment is available in the rear area of the centre colsone.●Extensive storage compartments and securing options in the load compartmentS400_053●Good load compartment partitioning thanks to variably adjustable load compartment covers27BodyLoad compartment conceptThe load compartment in the Golf Variant 2007 has been enlarged in comparison with its predecessor. Its concept has been designed to enable as many, diverse transportation tasks to be carried out as possible.●Bulky goods can be easily transported thanks e.g. to the folding rear seat backrest (split 60 : 40). A front passenger seat with through-loading function is optionally available.●The rear seat backrest can be folded to form a flat load floor thanks to the high mounted pivot point and therefore offers high loading ability.Bag hooks, foldingStorage compartment for warning triangle and first aid kitLarge storage compartment in the luggage compartment floor cover folded completely forwardsLarge storage compartment in the luggage compartment floor -28●The compartments in the optionally available, variable load floor offer optimal storage options. The cover of the large, rear storage compartment can be folded over completely or raised to various angles. This enables the load compartment to be sub-divided into separate areas.Through-loading apertureStorage compartment openLashing ringS400_054 Lashing ringCover raised verticallySmall storage compartment in the luggage compartment floor cover open29Occupant protectionSafety equipmentThe Golf Variant is fitted with the safety equipment familiar from the Jetta.●The front passenger airbag can be deactivated via a key switch in the storage compartment on the front passenger side.●Driver and front passenger airbags●Seat belt prompt for driver and front passenger●Seat belt pre-tensioners and belt tension limiters for the front seats●Optional rear side airbags in combination with seat belt pre-tensioners and belt tension limiters●3-point seat belts on all seats●Isofix attachment points on the rear, outer seats●Pressure sensors in the front doors30Top Tether The Golf Variant is equipped with the Top Tether system.●Side airbag in the front seats with two chambers●Curtain airbag for front and rear occupantsCover with Top Tether lettering●Top Tether systemS400_112Top Tether retainerThe Top Tether system serves to secure a child seat more firmly. In this case, an additional, upper belt on the child seat is attached to corresponding retainers on the vehicle floor behind the rear seat bench.S400_055●Acceleration sensors in the rear wheel housing linersFurther information on the occupant protection systems can be found in self-study programme 318 "The Golf 2004".31EnginesEngine/gearbox combinationsPetrol engine 5-speed manual gearbox 0AF 5-speed manual gearbox 0A4 6-speed manual gearbox 0AJDiesel engine1.6l 75 kW petrol engine with 2-valve technology1.4l 90 kW TSI engine with turbocharger1.4l 103 kW/125 kW TSI engines with dual charging2.0l 147 kW TSI engine with turbocharger1.9l 77 kW TDI engine with 2-valve technology2.0l 103 kW TDI engine with 4-valve technology2.0l 103 kW TDI engine with 2-valve technology326-speed manual gearbox 02S6-speed manual gearbox 02Q6-speed automatic gearbox 09G6-speed directshift gearbox 02E7-speed double-clutch gearbox 0AM33EnginesThe new engine code systemTo reduce engine code diversity, the 3-digit engine codes will be provided with a new, fourth digit. This applies only to engines with an identical, basic engine but different outputs In the case of these engines, output differentiation takes place solely via the engine control unit, in which case the software is adapted to implement the different output and torque. Engines with a modified emissions concept will not be provided with changed engine codes. The new engine code generation can be recognised as follows:● ●●The first digit of the engine codes is a "C". The 3-digit engine codes will continue to be used on the engine block. The 4-digit engine codes can only be seen on the vehicle data sticker, the control unit and the model plate.The assignment of the new engine codes is shown using the following example case:2.0l 103 kW TDI 4V2.0l 100 kW TDI 4V2.0l 96 kW TDI 4VBKDAZVBEEEngine codes - previouslyEngine codes - new with 4 digitsCKDACKDBCKDCS400_10434Where does identification take place?The 4-digit engine codes are written on the control unit, the model plate and the vehicle data sticker.Vehicle data stickerSticker on the engine control unitS400_094Model plateS400_091S400_093The 3-digit engine code will be retained as part of the engine number; these are stamped onto the engine block.A sticker with the engine codes and a sequential number is affixed onto the engine in the visible area (toothed belt guard, valve cover).Engine code on the engine blockSticker with engine codeS400_095 S400_09635EnginesThe 1.6l 75 kW petrol engine with 2-valve technologyThis engine is identical to the 1.6l 75 kW petrol engine fitted in the current Jetta. Technical features● ● ● ● ●●●2-valve roller rocker arm Aluminium engine block with ribbed sump Secondary air system Plastic variable intake manifold Pressure sensor system, previously hot-film air mass meter (HFM) Omission of the crankcase breather, venting only via the cylinder head Omission of the exhaust gas recirculation systemS400_015Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel BSE 4-cylinder in-line engine 1595 cm3 81 mm Torque (Nm)Torque and output diagram2 10.3 : 1 75 kW at 5600 rpm 148 Nm at 3800 rpm Simos 7.1 Super unleaded RON 95 (normal unleaded RON 91 with reduction in performance) Probe before catalytic converter linear lambda probe, Probe after catalytic converter: transient probe EU 4Exhaust gas treatmentEngine speed (rpm)S400_016Emissions standard36Output (kW)77.4 mmThe 1.4l 90 kW TSI engine with turbochargerThe 1.4l 90 kW TSI engine is a further example of the TSI engine model series. However, it is charged using a turbocharger. It replaces the 1.6l 85 kW FSI engine, and offers significantly better performance than this engine with considerably lower fuel consumption. Technical features● ● ●● ● ● ●●Homogenous mode (Lambda 1) Turbocharger with waste gate Plastic intake manifold with integrated charge air cooler Liquid-cooled charge air cooler Dual-circuit cooling system Fuel system regulated according to requirements High-pressure fuel pump with integrated pressure limiting valve Innovative combustion process with intake manifold flap change-overS400_105Further information on this engine can be found in self-study programme 405 "The 1.4l 90 kW TSI Engine with Turbocharger".Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel Exhaust gas treatment Emissions standard CAXA 4-cylinder in-line engine 1390 cm3 76.5 mm Torque (Nm)Torque and output diagram4 10 : 1 90 kW at 5500 rpm 200 Nm at 1500-3500 rpm Bosch Motronic MED 17.5.20 Super unleaded RON 95 Main catalytic converter, Lambda control EU 4Engine speed (rpm)S400_106Output (kW)75.6 mm37EnginesThe 1.4l 103 kW/125 kW TSI engines with dual-chargingAbove all, the special feature of these engines is the combination of direct petrol injection, dual-charging and downsizing. - In dual-charging, these engines are charged subject to requirements by a mechanical compressor and/or a turbocharger. - Downsizing means replacing a large-capacity engine with a powerplant with smaller displacement and/or fewer cylinders. This reduces the internal friction and therefore fuel consumption without any reduction in output or torque. Thanks to this concept, these engines surpass the performance of engines with the same output and also consume less fuel.S400_041Further information on these engines can be found in self-study programme 359 "The 1.4l TSI Engine with Dual-charging".Technical features● ● ● ● ● ●Two output variants with 103 kW and 125 kW Homogenous mode (Lambda 1) Double injection catalytic converter heating Turbocharger with waste gate Additional mechanical supercharger Charge air cooling●● ● ● ●Engine cover with vacuum tank for intake manifold flap change-over Grey cast iron cylinder block Dual-circuit cooling system Fuel system regulated according to requirements High-pressure fuel pump with a delivery pressure of up to 150 bar38Technical data 1.4l 103 kW TSI engine Torque and output diagram 1.4l 125 kW TSI engine Torque and output diagramTorque (Nm)Output (kW)Torque (Nm)Engine speed (rpm)S400_043Engine speed (rpm)S400_044Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel BMY 4-cylinder in-line engine 1390 cm3 BLG 4-cylinder in-line engine 1390 cm3 76.5 mm 75.6 mm 4 10 : 1 125 kW at 6000 rpm 240 Nm at 1750 to 4500 rpm Bosch Motronic MED 17.5.1 Super Plus RON 98 (Super unleaded RON 95 with slightly higher consumption and slight torque reduction in the low engine speed range) Main catalytic converter, Lambda control EU 476.5 mm 75.6 mm 4 10 : 1 103 kW at 6000 rpm 220 Nm at 1500 to 4000 rpm Bosch Motronic MED 17.5.1 Super unleaded RON 95Exhaust gas treatment Emissions standardMain catalytic converter, Lambda control EU 4The different output and torque levels are achieved using software. The engine mechanics are the same in both engines.Output (kW)39EnginesThe 2.0l 147 kW TSI engine with turbochargerThe 2.0l 147 kW TSI engine with turbocharger is also fitted in the current Golf GTI, Jetta and Passat Variant models. Technical features●● ● ● ●● ● ●Single-pipe exhaust system with starter and underbody catalytic converter mounted near engine Ethanol-resistant Hitachi high-pressure pump Non-return fuel system Homogeneous fuel injection Decoupled drive chain wheel in the balancer shaft assembly Elliptical toothed belt pulley on crankshaft Mechanical brake servo pump Continuously adjustable charge air flapsS400_017Further information on this engine can be found in self-study programme 337 "The 2.0 l FSI Engine with Turbocharger".Technical dataEngine code Type Displacement Bore Stroke Compression ratio Maximum output Maximum torque Engine management Camshaft timing adjustment Fuel BWA 4-cylinder in-line engine 1984 cm3 82.5 mm 92.8 mm 10.5 : 1 147 kW at 5100 to 6600 rpm 280 Nm at 1800 – 4700 rpm Bosch Motronic MED 9.1 42° crank angle Super Plus unleaded RON 98 (Super unleaded RON 95 with slight reduction in performance) Two three-way catalytic converters with Lambda control EU 4 Torque (Nm)Torque and output diagramExhaust gas treatment Emissions standardEngine speed (rpm)S400_01840Output (kW)The 1.9l 77 kW TDI engine with 2-valve technologyThe 1.9l 77 kW TDI engine is also fitted in the Golf, and has already proved its worth in other Volkswagen models. Technical features● ● ●●Unit injectors with solenoid valves Adjustable turbocharger Optional engine version with catalytically coated diesel particulate filter Switchable cooler for exhaust gas recirculationInformation on the diesel particulate filter can be found in self-study programme 336 "The Catalytic Coated Diesel Particulate Filter".S400_019Technical dataEngine code BXE (without diesel particulate filter) BLS (with diesel particulate filter) 4-cylinder in-line engine 1896 cm3 79.5 mm 95.5 mm 2 18 : 1 77 kW at 4000 rpm 250 Nm at 1900 rpm Bosch EDC 16 with unit injector system Diesel, min. 51 CN Exhaust gas recirculation and oxidising catalytic converter/ diesel particulate filter EU 4 Torque (Nm)Torque and output diagramType Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel Exhaust gas treatment Emissions standardEngine speed (rpm)S400_020Output (kW)41EnginesThe 2.0l 103 kW TDI engine with 4-valve technologyThis engine is identical to the 2.0l 103 kW TDI engine in the Golf 2004. Technical features● ● ● ● ●Unit injectors with solenoid valves Adjustable turbocharger 4-valve technology Two camshafts, driven by toothed belts Switchable cooler for exhaust gas recirculationFurther information on this engine can be found in self-study programme 316 "The 2.0l TDI Engine".S400_021Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel Exhaust gas treatment Emissions standard BKD 4-cylinder in-line engine 1968 cm3 81 mm 95.5 mm 4 Torque (Nm)Torque and output diagram103 kW at 4000 rpm 320 Nm at 1750 rpm to 2500 rpm Bosch EDC 16 with unit injector system Diesel, min. 51 CN Exhaust gas recirculation and oxidation catalytic converter EU 4Engine speed (rpm)S400_02442Output (kW)18 : 1The 2.0l 103 kW TDI engine with 2-valve technology and diesel particulate filterThe 2.0l 103 kW TDI engine with 2-valve technology and diesel particulate filter is also available in the Golf model year 2006. Technical features● ● ●●Unit injectors with solenoid valves Catalytically coated diesel particulate filter Turbocharger raised and rotated upwards by 180° for mounting the diesel particulate filter close to the engine Ceramic glow plugsInformation on the diesel particulate filter can be found in self-study programme 336 "The Catalytic Coated Diesel Particulate Filter".S400_023Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel Exhaust gas treatment Emissions standard BMM 4-cylinder in-line engine 1968 cm3 81 mm 95.5 mm 2 Torque (Nm)Torque and output diagram103 kW at 4000 rpm 320 Nm at 1750 rpm to 2500 rpm Bosch EDC 16 with unit injector system Diesel, min. 51 CN Exhaust gas recirculation and diesel particulate filter EU 4Engine speed (rpm)S400_024Output (kW)18.5 : 143TransmissionManual gearboxes - overviewAlso see self-study programme No.:Manual gearboxTechnical features• Developed from 02T gearbox • Housing reinforced, gearbox adapted to modified installation position • Without speedometer sender–5-speed manual gearbox 0AF • Developed from 02J gearbox • Gearshift mechanism optimised, final drive reinforced, housing adapted • Without speedometer sender 5-speed manual gearbox 0A4 3286-speed manual gearbox 0AJ• Developed from 0AG gearbox • Adapted for the 1.4l 90 kW TSI engine, extended output shaft, distance between output shaft and differential increased, sheet metal bearing mounting replaced by cast bearing mounting for higher torques, toothing ground • Final drive reinforced, splines adapted for higher torques, housing adapted • Without speedometer sender3066-speed manual gearbox 02S• Developed from 02J gearbox • Gearshift mechanism optimised • Longer shafts with additional bearings, additional gear pair, new, longer aluminium housing cover, housing adapted to the installation position • Without speedometer sender306• Developed from 02M gearbox • Changes to selector shaft, selector forks with stops in housing, modified bearings • Without speedometer sender 6-speed manual gearbox 02Q30644Automatic gearboxes - overviewAlso see self-study programme No.:Automatic gearboxTechnical features6-speed direct-shift gearbox 02E is equipped with a hydraulic double clutch. It combines the advantages of a manual gearbox, such as high efficiency, robustness and sportiness, with the advantages of an automatic gearbox, i.e. high comfort, especially on changing gears.3086-speed direct-shift gearbox 02E7-speed double-clutch gearbox 0AM has been developed from direct-shift gearbox 02E. In contrast to the 02E, it operates with a double clutch, an electric oil pump for the hydraulic system and separate oil circuits for the gearbox and mechatronics.3907-speed double-clutch gearbox 0AM6-speed automatic gearbox 09G is a compact, light, electronically controlled gearbox for transverse mounting.3096-speed automatic gearbox 09G45Running gearThe running gearThe Golf Variant 2007's running gear continues the high standard of comfort and dynamics in its A platform segment. The Golf Variant is also equipped with modern McPherson strut front suspension. The modern four-link rear suspension deserves particular emphasis in terms of its vehicle dynamics and ride comfort. The electromechanical power steering gives the driver a precise steering feel and continuously adapts the required steering forces to the vehicle's increasing speed. The springs and shock absorbers have been matched to the vehicle's increased axle loads.●Electronic stabilisation programme based on the MK60 system from Continental Teves●Brake assist system●Electromechanical power steering system, 2nd generation●Modern McPherson strut front suspension●Direct anti-roll bar connection with a ratio of 1 : 1●Brake servo with dual rate characteristic curve46Further information on the running gear can be found in self-study programme No. 321 "The Golf 2004 Running Gear".●Four-link rear suspension with very good vehicle dynamics and comfort characteristicsS400_036●Track and camber separately adjustable on the rear axle●Tyre pressure monitor, optional with Trendline, standard with Comfortline●Vertical accelerator pedal with contact-free senders for the accelerator pedal position47Electrical systemThe fuse boxes and relay positions in the vehicle electrical systemInstallation locationsThe electrical system in the Golf Variant 2007 has been taken from the Jetta 2006 and has only been modified in the rear area. The installation locations of the electronics box, the pre-fuse box, the fuse box and the relay carrier are identical to those in the Golf.Relay carrier beneath dash panel on lefthand side, above the onboard supply control unitThe adjacent illustration shows the installation locations.Electronics box on the left in the engine compartmentPre-fuse box on the left in the engine compartmentFuse box in the dash panel on the lefthand side48Relay carrier on the onboard supply control unit, beneath the dash panel on the left-hand sideMore detailed information on the electrical system can be found in self-study programme 319 "The Golf 2004 Electrical System".S400_06649Electrical systemThe networking conceptOverview of networked electronic control unitsTo ensure flawless data exchange between the control units, these are networked via various data bus systems. The data bus diagnostic interface J533 (gateway) acts as the interface for the following data bus systems: CAN drive data bus CAN convenience data bus CAN infotainment data bus CAN instrument cluster data bus CAN diagnostic data busControl units connected to CAN drive data bus CAN convenience data bus CAN infotainment data bus CAN sensor data bus LIN data bus CAN instrument cluster data bus CAN diagnostic data bus CAN data bus line (high-speed and low-speed) LIN data bus line K-wire50Legend D E221 G85 G273 G384 G397 G419 H8 J104 J136 J217 J234 J245 J255 J285 J345 J362 J364 J386 J387 J388 J389 J393 J394 J400 J412 J431 J446 J500 J503 J519 J520 J525 J527 J533 J587* J604 J623 J743* NOx R T16 Ignition/starter switch Operating unit in steering wheel (multifunction steering wheel) Steering angle sender Interior monitoring sensor Vehicle inclination sender Rain and light sensor ESP sensor unit Anti-theft alarm system horn ABS control unit Seat and steering column adjustment control unit with memory function Automatic gearbox control unit Airbag control unit Sliding sunroof adjustment control unit Climatronic control unit Control unit in dash panel insert Trailer detector control unit Immobilizer control unit Auxiliary heater control unit Driver door control unit Front passenger door control unit Rear left door control unit Rear right door control unit Convenience system central control unit Sunroof roller blind control unit Wiper motor control unit Mobile telephone operating electronics control unit Headlight range control, control unit Parking aid control unit Power steering control unit Control unit with display for radio and navigation Onboard supply control unit Onboard supply control unit 2 Digital sound package control unit Steering column electronics control unit Data bus diagnostic interface Selector lever sensor control unit Auxiliary air heater control unit Engine control unit Mechatronic unit for direct shift gearbox NOx sensor Radio Diagnostic connectionS400_067*With double-clutch gearbox only51Heating and air conditioningAir conditioningThree different systems are available in the Golf Variant 2007:● ● ●The heater and fresh air system with 4-stage blower and recirculated air circuit The semi-automatic heater and air conditioner "Climatic" The heater and air conditioner "2C-Climatronic"Indirect ventilation (with 2C-Climatronic only) Vent for windscreenCentre vent Vent for front right footwell Vent for rear centre (for centre console with rear vents only, otherwise blind covers on the air conditioner unit) Vent for rear right footwellVent in the A-pillarVent in the dash panel Vent for front left footwellVent for rear left footwellS400_038If the vehicle is fitted with a centre console with rear vents, the storage compartment in the centre console can also be cooled.Further information on heating and air conditioning can be found in self-study programme No. 318 "The Golf 2004".S400_07152OperationDepending on the vehicle's equipment, four different types of control panels are available for the heating and air conditioning:● ●With or without instant heat button for the auxiliary coolant heater With or without potentiometer for the seat heating2C-Climatronic control panelS400_076Interior temperature sensor Button assignment if equipped with auxiliary coolant heaterIn comparison with the previous equipment, the lettering on the right-hand button has been changed from "ECON" to "AC". The centre button on the lower panel is labelled "DUAL". This function serves to match the temperature on the front passenger side to the temperature on the driver side. If the vehicle is fitted with an auxiliary coolant heater, this button panel serves as an instant heat button for the auxiliary coolant heater, and is labelled with the appropriate symbol. Matching the temperature on the driver and front passenger side is then carried out via "AUTO". Thermo Top V auxiliary coolant heater The Golf Variant 2007 can be fitted with the optional Thermo Top V auxiliary coolant heater. This undertakes the following tasks:● ● ●Acts as an auxiliary heater for heating the vehicle interior and defrosting the vehicle's windows, Acts as stationary ventilation to lower the interior temperature when the vehicle is parked in the sun, Acts as an additional heater in vehicles with petrol or diesel engines (instead of the PTC heater element in diesel engines).53Radio, telephone and navigationThe radio systems in the Golf Variant 2007RCD 300 radioThe entry-level RCD 300 radio system offers the following functions:●● ●● ●● ● ● ● ● ●●Four loudspeaker channels (20 Watts each), two or four channels can be optionally connected RDS FM/AM European radio (AM without LW) Indication of the stored stations with RDS names in the display FM 2-tuner diversity Control via the multi-function steering wheel (MFL) and multi-function indicator (MFI) Integrated single-CD player Control system for an external 6-disk CD changer Telephone control system (hands-free) GALA Self-diagnosis incl. loudspeaker diagnosis Driving school function, must be explicitly ordered (indication of turn signal function and speed via the display - coding function) Playback of music CDs in MP3 formatS400_057RCD 500 radioThe higher-quality RCD 500 radio system offers the following functions:● ● ●● ● ● ● ● ● ● ● ● ● ●Four loudspeaker channels (20 Watts each) RDS FM/AM European radio (AM without LW) Indication of the stored stations with RDS names in the display FM 2-tuner phase diversity Control via MFW and MFD Integrated 6-disk CD changer Control system for an external 6-disk CD changer Telephone control system (hands-free) GALA Traffic Information Memory (TIM) Vehicle model-specific sound adaptation Self-diagnosis incl. loudspeaker diagnosis Optional connection of an external sound amplifier Optional playback of music CDs in MP3 formatS400_058The cover frame has to be removed to remove or install a radio, in order to access the threaded connection located behind it.54Radio/navigation system RNS 300The entry-level radio/navigation system RNS 300 offers the following functions:● ●● ●● ● ●●Two-colour display (navigation via symbols) Four loudspeaker channels, two or four channels can be optionally connected 1 tuner principle for FM including TMC Dynamic guidance via TMC (Traffic Message Channel) Integrated CD player Control system for CD changer Navigation without navigation CD inserted (corridor function) Playback of music CDs in CDA, WMA and MP3 formatS400_059Radio/navigation system MFD 2The higher-quality radio/navigation system MFD 2 with integrated navigation system offers the following functions:● ●● ● ●● ●● ● ● ● ●●Multi-colour display (MFD) Dynamic guidance via TMC (Traffic Message Channel) Four loudspeaker channels (20 Watts each) RDS FM/AM European radio (AM without LW) Indication of the stored stations with RDS names in the display Control via MFW and MFD Audio CDs can also be played via the internal DVD player Control system for an external 6-disk CD changer Telephone control system (hands-free) GALA TIM Can be combined with Volkswagen Sound and Dynaudio Self-diagnosis incl. loudspeaker diagnosisS400_060For further information on radios, please refer to self-study programme 342 "Radio Systems".55Radio, telephone and navigationUniversal Mobile Phone Preparation (UMPP) LowIn the Golf Variant 2007, Universal Mobile Phone Preparation Low is fitted exclusively with BluetoothTM technology. The data are transmitted via BluetoothTM from the mobile phone to the mobile telephone operating electronics control unit. A cradle for the specific mobile phone model is required to hold the mobile phone in the mounting and to use the hands-free system. The mobile telephone operating electronics control unit communicates with the other control units via the CAN infotainment data bus. UMPP Low is suitable for the mobile telephone D and E networks.UMPP Low has the following functions:●● ● ●● ● ●● ●Operation and display are carried out on the mobile phone and partly via the multifunction steering wheel (optional). It has a hands-free system and radio mute switching. The mobile telephone's rechargeable battery is charged via the mobile phone mounting. The info and breakdown buttons are located on the mobile phone mounting. These signals are transferred via a discrete cable connection. The vehicle is equipped with a GSM vehicle antenna system, which is connected directly to the mounting. There is a CAN data bus interface to the CAN infotainment data bus. Data transfer between the mobile phone and the mobile telephone operating electronics control unit takes place via a BluetoothTM interface. This UMPP is diagnosis-capable. The power-down time can be set (max. 60 minutes).As the mobile telephone is always connected via the BluetoothTM interface, a pairing process has to be carried out once. Please check the latest VOTEX information at www.volkswagen-zubehoer.de for the availability of telephone mountings for the various mobile phones.56J453J503E440 CAN infotainment data bus R65J527J533 CAN convenience data busBluetoothTM audio data transmission 64 kbit/sec via HFP*R54J412J519R38 S400_097Charger and button lineMounting on instrument panelLegend E440 J412 J453 J503 Multifunction buttons on left in steering wheel (optional) Mobile telephone operating electronics control unit Multifunction steering wheel control unit (optional) Control unit with display for radio and navigation J519 J527 J533 R38 R54 R65 Onboard supply control unit Steering column electronics control unit Data bus diagnostic interface Telephone microphone Mobile telephone Telephone aerial*Hands-free profile57Radio, telephone and navigationThe aerial conceptRadio systems RCD 300 and RCD 500S400_061The RCD 300 and RCD 500 radio systems require two aerials for the internal dual-tuner diversity receiver to receive radio signals. The AM/FM aerial is designed as a roof mounted aerial. The FM aerial is located in the rear right side window.Radio/navigation system RNS 300Auxiliary heater radio receiverS400_062The RNS 300 radio/navigation system only requires one aerial for the internal 1 tuner radio receiver to receive radio signals. The AM/FM aerial is located in the rear right side window. The signals for telephone, auxiliary heater and navigation are received via a separate roof aerial.58Radio/navigation system RNS MFDAuxiliary heater radio receiverS400_098The RNS MFD radio/navigation system requires two aerials for the internal dual-tuner diversity receiver to receive radio signals. The AM/FM aerial is located in the rear right side window, the FM aerial in the rear left side window. The signals for telephone, auxiliary heater and navigation are received via a separate roof aerial.59400© VOLKSWAGEN AG, Wolfsburg All rights and rights to make technical alterations reserved. 000.2812.02.20 Technical status 05.2007 Volkswagen AG Service Training VSQ-1 Brieffach 1995 D-38436 Wolfsburg❀ This paper has been manufactured from pulp bleached without the use of chlorine.