TECHNICAL DOCUMENTATION

SSP 442 The 1,6ltr TDI Engine

PDFEN48 pages3 MB
SSP 442 The 1,6ltr TDI Engine - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingSelf-study Programme 442The 1.6ltr. TDI Engine with Common Rail Injection System Design and Function The 1.6l TDI engine with common rail injection system will form the basis for all future four-cylinder diesel engines. This engine represents a new generation of efficient, economical and dynamic diesel engines from Volkswagen. Following the 2.0l 103kW TDI engine with common rail injection system, the 1.6l TDI engine is now being launched in different output levels. The 1.6l TDI engine sees Volkswagen continue a success story in the diesel segment that began in 1993 with the first direct-injection turbocharged diesel car engine.The engine sets standards in terms of dynamics, driving fun, consumption and reliability. In addition, the use of common rail technology allows a clear improvement in comfort and noise. Volkswagen is very well prepared with this engine when it comes to future emissions standards. It fulfils the EU5 emissions standard.S442_001The self-study programme portrays the design and function of new developments. The contents will not be updated.For current testing, adjustment and repair instructions, refer to the relevant service literature.Important Note2 ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Engine Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Functional Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43Test Yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443 Introduction1.6l TDI engine with 4-valve technologyThe 1.6l TDI engine with 4-valve technology is based on the 2.0l 103kW TDI engine with common rail injection system. The engine comes in three power versions — 55kW, 66kW and 77kW. Thanks to continued further development of tried and tested technology and the new common rail injection system from Continental (PCR 2), these engines fulfil the EU5 emissions standard. The engine is used in the Polo, Golf and Passat.CrankcaseCylinder head coverExhaust gas recirculationS442_220PistonOil pumpOil filter module4 In some countries, the engine will be available with emissions standard EU3. The following self-study programme looks at the new features compared with the 2.0l 103kW TDI engine with common rail injection system.Common rail fuel injection systemCylinder headExhaust gas recirculation moduleS442_218Engine mountingDrive for ancillary unitsToothed belt driveYou will find further information on the 2.0l 103kW TDI engine in self-study programme no. 403 “The 2.0-ltr. TDI Engine with Common Rail Injection System”.5 IntroductionTechnical features●● ●●●Common rail injection system with piezo injectors and maximum injection pressure of 1600bar Adjustable turbocharger Exhaust gas recirculation module comprising exhaust gas recirculation system with exhaust gas recirculation valve and exhaust gas recirculation cooler Diesel particulate filter with oxidation catalytic converter Plastic intake manifoldS442_057Technical data1.6l 55kW TDI engineTorque and output diagramEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel Exhaust gas treatment Emissions standard CO2 emissions CAYA 4-cylinder in-line engine 1598cm3 79.5mm 80.5mm Torque [Nm] 4 16.5:1 55kW at 4000 rpm 195Nm at 1500-2000 rpm Simos PCR2 Diesel complying with DIN EN590 Exhaust gas recirculation, oxidation catalytic converter and diesel particulate filter EU5 109g/km (Polo 2010) 270 240 210 180 150 120 90 60 30 1000 3000 5000 90 80 70 60 50 40 30 20 10 S442_070 Power [kW]Engine speed [rpm]6 1.6l 66kW TDI engineTorque and output diagram270 240 210 180 Torque [Nm] 150 120 90 60 30 1000 3000 5000 90 80 70 60 50 40 30 20 10 S442_012 Power [kW] Power [kW]Engine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel Exhaust gas treatment Emissions standard CO2 emissionsCAYB 4-cylinder in-line engine 1598cm379.5mm 80.5mm 4 16.5:1 66kW at 4200 rpm 230Nm at 1750-2500 rpm Simos PCR2 Diesel complying with DIN EN590 Exhaust gas recirculation, oxidation catalytic converter and diesel particulate filter EU5 118g/km (Golf 2009)Engine speed [rpm]1.6l 77kW TDI engineTorque and output diagramEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel Exhaust gas treatment Emissions standard CO2 emissions CAYC 4-cylinder in-line engine 1598cm3 79.5mm 80.5mm Torque [Nm] 4 16.5:1 77kW at 4400 rpm 250Nm at 1900-2500 rpm Simos PCR2 Diesel complying with DIN EN590 Exhaust gas recirculation, oxidation catalytic converter and diesel particulate filter EU5 118g/km (Golf 2009) 270 240 210 180 150 120 90 60 30 1000 3000 5000 90 80 70 60 50 40 30 20 10 S442_014Engine speed [rpm]7 Engine ComponentsCylinder blockThe weight of the cylinder block has been reduced by approx. 6kg compared with the 2.0l 103kW TDI engine thanks to various measures. This includes the omission of: Bolting points, ribs and various unnecessary mounts.The reduced displacement has been achieved with a smaller cylinder diameter and a shorter stroke. The cylinder diameter is 79.5mm. The stroke of 80.5mm is achieved with smaller diameter crank pins on the crank shaft.S442_058PistonThe piston is a die-cast part made from aluminium. The shape of the piston recess allows good fuel swirl generation and improves the mixture formation. The piston bushing could be omitted due to the lower thermal loading.2.0l TDI engine Piston recess1.6l TDI enginePiston bushingS442_050S442_0488 Cylinder headThe cylinder head on the 1.6l TDI engine with common rail injection system has two inlet valves and two exhaust valves for each cylinder. The camshafts are driven by the crankshaft via a toothed belt and the spur gear teeth. An oval exhaust gas port and a spiral-shaped intake port allows a faster gas flow. This contributes to a better mixture formation. The valves are actuated by roller rocker fingers with hydraulic valve play compensation.Spur gear teeth Injectors Inlet camshaftCylinder head Roller rocker fingers Exhaust camshaft Exhaust ports S442_061Cylinder head coverThe cylinder head cover has two outer clamping pieces for securing the injectors. The seals for the injectors are in the cylinder head cover.Clamping piece with central bolt for securing two injectorsS442_066 Seal9 Engine ComponentsToothed belt driveThe camshaft, the high-pressure pump for the common rail system and the coolant pump are driven by the toothed belt. The width of the toothed belt has been reduced by 5mm to 25mm and all sprockets, belt tensioners and guide rollers have been modified accordingly.Camshaft sprocket Toothed beltHigh-pressure pumpBelt tensionerGuide rollerCoolant pump CrankshaftS442_07210 Ancillary component driveThe ancillary components are driven via a flexible, stretchable poly V-belt, called a flexi belt. The belt tensioner is not required due to the use of the flexi belt. There are two different versions:1. Poly V-belt drive for vehicles without air-conditioning compressor. Only the alternator is driven by the poly V-belt in this case.2. Poly V-belt drive for vehicles with air-conditioning compressor. All ancillary units are driven by a poly V-belt with guide roller.AlternatorGuide rollerAlternatorS442_076 Crankshaft Flexi belt Crankshaft Flexi beltS442_074 Air conditioner compressorThe guide roller has a fixed mounting position and should not be confused with a belt tensioner. Please refer to the assembly instructions in the repair guide.11 Engine ComponentsExhaust gas recirculation systemOn the 1.6l TDI engine, the exhaust gas recirculation valve and the exhaust gas cooler with exhaust gas flap have been combined into a single module. The advantages of the modular design are a compact space requirement and, at the same time, a shorter control path. The exhaust gas recirculation module is bolted to the exhaust side of the cylinder head and the exhaust manifold. The module is connected to the intake manifold directly through the cylinder head. This allows additional cooling of the recirculated exhaust gases.Passage through cylinder headExhaust gas recirculation moduleExhaust gas from engine Exhaust gas to intake manifoldS442_212CoolerS442_214Exhaust gas recirculation valveVacuum unit for exhaust gas flapDesignExhaust gas recirculation valve, closed Curved disc Exhaust gas flap, open Exhaust gas from engineS442_242Exhaust gas flap, closed Exhaust gas to intake manifold Exhaust gas recirculation valve, open Cooler Coolant inletCoolant outlet12 FunctionThe exhaust gas recirculation helps reduce nitrogen oxide emissions. Part of the exhaust gases are returned to the combustion process. The recirculation quantity is regulated by the engine control unit taking the engine speed, intake air quantity, intake air temperature, injection quantity and air pressure into account.AN18BN345CG69J623J338G39 Legend G39 G62 G69 J338 J623 N18 N345 A B C Lambda probe Coolant temperature sender Throttle valve potentiometer Throttle valve module Engine control unit Exhaust gas recirculation valve Exhaust gas recirculation cooler change-over valve Exhaust gas recirculation module Vacuum unit Catalytic converter S442_222G62You will find more information on how the exhaust gas recirculation system works in self-study programme no. 316 “The 2.0l TDI Engine”.13 Engine ComponentsIntake manifoldThe intake manifold is made from plastic. The combination of all exhaust gas recirculation components in the new exhaust gas recirculation module on the exhaust side means there is no separate exhaust gas recirculation valve on the intake manifold. As a result, an aluminium intake manifold is not required.Intake manifold flap motor V157S442_064The intake manifold flap motor V157 and the swirl flap adjustment, which it is linked to, currently do not have a function. The intake manifold flap motor V157 and the intake manifold flap potentiometer G336 are currently not included in the self-diagnosis.14 Oil systemThe oil pump generates the oil pressure required to lubricate the engine. It is driven by the crankshaft via a separate toothed belt. The filter bypass valve opens when the filter is clogged up to ensure lubrication of the engine.1317 141216 159 11 1661084 5 7 16 3 1 S442_228 2 Legend 1 2 3 4 5 6 7 8 9 Oil sump Oil level and oil temperature sender G266 Oil pump Control plunger Oil non-return valve Filter bypass valve Oil cooler Oil filter Oil pressure retention valve 10 11 12 13 14 15 16 17 Crankshaft Jets for piston cooling Inlet camshaft bearing Exhaust camshaft bearing Vacuum pump Turbocharger Oil return Oil pressure switch F115 Engine ComponentsOil pumpThe oil pump is a regulated duo-centric pump with an internal limiter. The pump is driven by the crankshaft via a separate, maintenance-free toothed belt without tensioner. The oil pump draws the oil out of the oil sump and pumps it into the oil circuit.Toothed belt Oil pumpDesignS442_232 Control boreOil circuit Control plungerPressure spring Oil from oil sumpOil pump caseDrive shaftOuter rotor Inner rotorS442_23016 FunctionControl circuit closed:Pressure spring Control plunger From oil circuit To the oil circuitThe oil pump contains a control plunger. This springloaded control plunger closes the circuit inside the pump. The spring force acts on the control plunger and pushes it forwards. The oil is delivered to the oil circuit.S442_224 Oil from oil sump Outer rotor Inner rotorControl circuit open:Pressure spring Control plunger From oil circuit To the oil circuit Internal circuitS442_226 Oil from oil sump Outer rotor Inner rotorThe control plunger is connected to the oil circuit via control bores. If the oil pressure rises in the oil circuit, the control plunger is pressed back against the spring. This opens the circuit inside the pump. The oil is delivered to the pump chamber and the pump conveys the oil inside the pump housing. As soon as the pressure in the oil circuit falls, the control plunger closes the internal circuit and the oil can be pumped into the oil circuit again. No additional safety valve is required for pressure limitation due to the way the control plunger works.17 Engine ComponentsOil filter moduleThe plastic casing of the oil filter and the oil cooler made from aluminium are combined in the oil filter module. The module is bolted directly to the crankcase. Coolant is supplied directly from the crankcase.Oil filterOil filter module S442_234SealOil coolerS442_06018 Coolant circuitThe coolant is circulated around the coolant circuit by a mechanical coolant pump. The pump is driven by the toothed belt. The system is controlled by an expansion-type thermostat. The engine is equipped with a low-temperature exhaust gas recirculation system to reduce nitrogen oxide emissions.S442_043Legend 1 2 3 4 5 6 7 8 9 10 Radiator for engine coolant circuit Thermostat Coolant pump Oil cooler Cooler for exhaust gas recirculation Coolant temperature sender G62 Radiator outlet coolant temperature sender G83 Heat exchanger for heating system Expansion tank Coolant circulation pump 2 V178You will find further information on the lowtemperature exhaust gas recirculation system in self-study programme no. 403 “The 2.0ltr. TDI Engine with Common Rail Injection System”.19 Engine ComponentsImproved engine mountThe 1.6l TDI engine does not have a balancer shaft. The new engine mount reduces vibrations that are felt by occupants. Tasks of an engine mount:● ● ● ●Securing the engine in the engine compartment; statically (when stationary) and dynamically (on the road) Bearing the static engine load Reducing the vibrations from uneven road surfaces (shaking) Reducing the vibrations transferred from the engine to the bodyEngine mounts are used in vehicles to prevent the transfer of vibrations from the engine to the body and to dampen the resonance vibration of the engine. Extremely hard and highly stiff mounts are required to bear the engine load and secure the engine in the engine compartment. Soft bearings are required for good acoustics in the vehicle interior. These ensure a low dynamic stiffness across a broad frequency range. In order to find a compromise for all tasks, engine mounts filled with hydraulic fluid, called hydro-mounts, are fitted.New engine mountThe efficiency of the new engine mount has been improved by modifying the design of its hydraulic system. Careful configuration of the geometry has made it possible to use the fluid in hydraulic mounts as an “internal damper”.Main chamberUpper casing of decoupling moduleDecoupling diaphragmS442_028 Damping passage Compensating chamber Passage for damping fluidS442_030Compensating chamberDecoupling moduleDamping passage Lower casing of decoupling module20 FunctionLarge vibration amplitude When a greater vibration amplitude acts on the mount, for example, due to an uneven road surface, the vibration energy is reduced by the damping system inside the hydro mount. This is achieved by the hydraulic fluid being pressed out of the main chamber into the compensating chamber via the damping passage. The damping reduces the shaking to a comfortable level.Main chamberDamping passageS442_166Compensating chamberSmall vibration amplitude If a small vibration amplitude acts on the mount, for example, from engine vibrations, the damping will be deactivated by the decoupling diaphragm mounted on floating bearings. In the new engine mount, the decoupling diaphragm vibrates within a certain speed/frequency range together with the hydraulic fluid against the vibrations produced by the engine. The decoupling diaphragm mounted on floating bearings prevents premature hardening of the mount. This decreases the vibrations transferred to the body. The humming/droning noises are reduced to a comfortable level so there is no need for a balancer shaft.Main chamberS442_168Decoupling diaphragmThe fluid in the engine mount is made from dihydric alcohol (propylene glycol); commonly known as anti-freeze.Damage to the area around the engine mount diaphragm will cause a loss of hydraulic fluid in the mount and incorrect functioning.21 Engine ComponentsFuel system (Golf 2009)1 - Fuel system pressurisation pump G6 The fuel system pressurisation pump constantly delivers fuel to the supply line. 4 2 - Fuel filter with pre-heater valve The pre-heater valve prevents the filter becoming clogged with crystallising paraffin crystals at low outside temperatures. (The pre-heater valve is mounted separately in the Polo 2010.) 9563 3 - Pre-supply pump The pre-supply pump is part of the high-pressure pump and delivers the fuel from the supply line to the high-pressure pump unit.2 4 - Fuel temperature sender G81 The fuel temperature sender measures the current fuel temperature.Colour code/legend5 - High-pressure pump The high-pressure pump generates the high fuel pressure required for injection.High pressure 230 – 1600bar Return pressure from the injectors 1bar Supply pressure/return pressure6 - Fuel metering valve N290 The fuel metering valve controls on demand the quantity of fuel to be compressed.22 87 7 - Fuel pressure regulating valve N276 The fuel pressure regulating valve adjusts the fuel pressure in the high-pressure area.8 - High-pressure accumulator (rail) The high-pressure accumulator stores the fuel required for injection into all cylinders under high pressure.111111119 - Fuel pressure sender G247 The fuel pressure sender measures the current fuel pressure in the high-pressure area.10 10 - Pressure retention valve The pressure retention valve is used to stabilise the pressure in the return line to avoid fluctuations at the injectors and ensure the function of the piezo injectors. It keeps the pressure in the return line almost constant.S442_1301The fuel system components are explained over the following pages.11 - Injectors N30, N31, N32, N33 The injectors inject the fuel into the combustion chambers.23 Engine ComponentsCommon rail fuel injection systemThe common rail fuel injection system was developed by Volkswagen and Continental. It is made up of: The engine control unit The injectors The high-pressure accumulator (rail) The fuel pressure sender The fuel pressure regulating valve The high-pressure pipes The high-pressure pump The common rail injection system allows optimum and efficient mixture formation and combustion. The following always applies: The higher the injection pressure, the smaller the droplets of fuel and the better the mixture formation. The basic feature of the common rail system is that the injection pressure (max. 1600bar) can be generated regardless of the engine speed and the injection quantity.The high-pressure pump consists of: The mechanical pre-supply pump The fuel metering valve The high-pressure pump unitInjectorsFuel pressure senderFuel pressure regulating valveHigh-pressure accumulator (rail)High-pressure pumpS442_21024 The pressure generation and fuel injection are separated with the aid of the storage volume in the high-pressure accumulator (rail). The pressure is generated by a radial-piston type, high-pressure pump that conveys the fuel to the high-pressure accumulator (rail).The injectors are connected to the high-pressure accumulator by short high-pressure pipes. Being the centrepiece of the system, the injectors have the task of injecting the fuel into the combustion chamber.Needle stroke [mm]Pilot injectionMain injectionSecondary injectionControl current [A] 5-9Voltage [V] 80-150 S442_254Crank angle [°]A pulse sent to the injector by the engine control unit at the right time initiates the injection process. The opening duration and system pressure determine the injection quantity. In addition, the fuel can be divided into several individual injections per combustion cycle: Very small quantities of fuel in the pilot injections are followed by the main injection and then several secondary injections for active regeneration.While the pilot injections make the rise in pressure in the combustion chamber more constant and thus reduce the combustion noise, the secondary injections are intended for exhaust gas treatment. Together with the powerful control unit and the injectors with small tolerances, the common rail injection system clearly reduces consumption and emissions. At the same time, it increases the engine power and allows quieter running.25 Engine ComponentsHigh-pressure pumpThe high-pressure pump comprises the following components: Pre-supply pump Fuel metering valve High-pressure pump unitAll parts are combined in a single housing.Pre-supply pumpHigh-pressure pump unitFuel returnFuel metering valve N290Fuel inletHigh-pressure connection (to rail)S442_094High-pressure pump unitFuel returnFuel inletFuel metering valve N290Pre-supply pump S442_09626 Fuel system within high-pressure pumpThe electric fuel pump pumps diesel fuel out of the fuel tank through the fuel filter to the pre-supply pump. The pre-pressure regulation valve controls the fuel pressure in the pre-supply pump. It opens at 5bar and returns the fuel to the intake side of the pre-supply pump. The pre-supply pump delivers the fuel to the high-pressure pump via the actuated fuel metering valve. From the high-pressure pump, the fuel passes through the fuel pressure regulating valve to the high-pressure accumulator (rail) and then via high-pressure pipes to the injectors.To high-pressure accumulator High-pressure pumpFrom fuel tankPre-supply pump Fuel metering valve Pre-pressure regulation valve High-pressure pump unit S442_15627 Engine ComponentsPre-supply pumpThe pre-supply pump is a mechanically-operated gear wheel pump and is part of the high-pressure pump. It has the task of delivering the fuel supplied from the fuel tank to the high-pressure pump via the fuel metering valve. The fuel pressure is increased to approx. 5bar. This guarantees a constant supply of fuel to the high-pressure pump in all engine operating modes.S442_236Fuel inletFuel metering valve N290S442_110Pre-supply pumpEffects upon failureIf the high-pressure pump unit is not supplied with fuel. You cannot start the engine.28 Fuel metering valve N290The fuel metering valve controls the fuel supply to the high-pressure pump unit and ensures that fuel is supplied to the high-pressure pump. This allows the delivery quantity of the high-pressure pump to be adjusted to the engine requirements on the low-pressure side. The advantage of this is that the high-pressure pump only has to generate the pressure which is required for the current operating situation.Fuel metering valveS442_240FunctionValve not activatedPlunger Pressure spring Solenoid Armature Pressure springValve activatedPlunger Solenoid, powered ArmatureConnection for fuel supply to high-pressure pump S442_102 Connection for fuel supply from the pre-supply pumpConnection for fuel supply to high-pressure pump S442_100 Connection for fuel supply from the pre-supply pumpThe fuel metering valve is not powered. The spring force moves the plunger to close the passage to the high-pressure pump. The fuel supply to the highpressure pump is interrupted.The fuel metering valve is powered and the solenoid generates a magnetic field. The plunger is pressed against the spring force by the valve armature. The fuel supply to the high-pressure pump is opened and fuel reaches the high-pressure pump.Effects upon failureThe valve is closed if the voltage supply fails. Fuel is not delivered to the high-pressure pump. You can no longer start the engine.29 Engine ComponentsHigh-pressure pump unitThe high-pressure pump unit has the task of generating the high fuel pressure of up to 1600 bar, which is required for fuel injection. It is an on-demand radial piston pump with two highpressure units arranged at 180 ° that are operated by a cam.S442_238 High-pressure pump unitCompression chamberInlet valve, closedDelivery stroke The cam pushes the piston upwards. The inlet valve is closed by the spring force and the pressure builds up in the compression chamber. The outlet valve opens when the pressure inside the compression chamber is greater than the fuel pressure in the high-pressure accumulator.Outlet valve, open To rail PistonCamSuction stroke The downwards movement of the piston creates a vacuum in the compression chamber that opens the inlet valve against the spring force. The fuel coming from the fuel metering valve is drawn in. At the same time, the outlet valve is closed due to the difference in pressure between the compression chamber and the fuel pressure in the high-pressure accumulator.Fuel from fuel metering valvePistonOutlet valve, closedS442_106 Inlet valve, open Compression chamber30 High-pressure accumulator (rail)The rail is a high-pressure accumulator for the fuel that is delivered by the high-pressure pump. It supplies the injectors with the quantity of fuel required for all operating modes.High-pressure connection from high-pressure pumpConnections for injectorsReturn line to fuel tankS442_098 Fuel pressure sender G247 High-pressure accumulator (rail) Fuel pressure regulating valve N276Fuel pressure sender G247The fuel pressure sender G247 measures the fuel pressure in the rail. The pressure is converted into a voltage signal that is evaluated by the engine control unit. Based on the maps stored in the engine control unit, the pressure signal is used to calculate the activation period of the injectors and the high-pressure regulation by the fuel metering valve. The fuel pressure sender is bolted directly onto the high-pressure accumulator.S442_158Effects upon failureIf the signal fails or there is an implausible signal from the sender, the engine control unit switches to emergency-running mode. The engine power is reduced and the maximum engine speed limited to 3000 rpm.31 Engine ComponentsFuel pressure regulating valve N276The fuel pressure regulating valve is located on the high-pressure accumulator (rail). It regulates the fuel pressure in the high-pressure accumulator. The engine control unit uses a pulse-width modulated signal to operate the valve.S442_116DesignValve needle SolenoidFuel return Fuel pressure in highpressure accumulatorValve seatS442_124 Valve springValve ball Fuel return Valve armature32 FunctionRegulating valve not activated Upon “Engine OFF”, the valve ball is pressed into the valve seat only by the spring force. This maintains a low fuel pressure. If the fuel pressure in the high-pressure accumulator is greater than the spring force, the valve opens and fuel flows to the fuel tank via the fuel return.S442_120Regulating valve activated The engine control unit adjusts the operating pressure in the high-pressure accumulator by operating the solenoid with a pulse-width modulated signal. The valve armature is energised and presses the valve needle into its seat. The quantity flowing into the fuel return line is varied in relation to the duty cycle.S442_122Effects upon failureThe engine will not run if the fuel pressure regulating valve fails. The fuel pressure required for injection cannot be built up.33 Engine ComponentsInjectorsThe (piezo) injectors, which are connected to the rail via a high-pressure line, inject the quantity of fuel required for all engine operating modes into the combustion chambers. The respective injection quantity is made up of a pilot injection quantity, a main injection quantity and a secondary injection quantity. The injectors are controlled by a piezo actuator. This results in very short switching times, map-controlled injection quantities and a “smoother” combustion process.Injector (piezo actuator) not activatedThe fuel reaches the control chamber and the highpressure chamber of the injector via the high-pressure supply line. The force (F1) acting on the control plunger is greater than the force (F2) acting on the nozzle needle. The nozzle is closed. The pressure spring closes the return with the valve plunger to prevent the fuel flowing out when the engine is not turning over.Fuel returnValve plungerPiezo actuator Pressure spring High-pressure supply High-pressure supply S442_136 Fuel return F1 Control plunger Control chamberControl plungerF1F2High-pressure chamberInjector needle S442_140 S442_134 F2 Nozzle tip34 The design and function of the piezo actuator is described in self-study programme no. 351 “The common rail fuel injection system fitted in the 3.0l V6 TDI engine”.Injector (piezo actuator) activatedThe piezo actuator in the injector is activated and expands. The valve plunger is pushed against the spring force and connects the control chamber to the fuel return. This reduces the pressure in the control chamber. The hydraulic force (F2) at the nozzle needle is now greater than the force (F1) applied by the control plunger. The nozzle needle moves upwards and the fuel is injected into the combustion chamber.Fuel returnValve plungerPiezo actuator Pressure spring High-pressure supply High-pressure supply F1 Fuel return Control plunger S442_138 Control chamberControl plungerF1F2High-pressure chamberInjector needle F2 S442_160 Nozzle tip S442_14235 Engine ComponentsIdentification of injectorsThere is a data carrier on the top of the injectors. In addition to the VW parts number, date and type test number, the 6-digit IIC code (Injector Individual Correction) is stamped there. The IIC code needs to be entered in the Guided Function “Read/adapt correction values for injectors” when the injectors are replaced.Date (4-digit)DMC code 18x18 Data matrix code for encrypting manufacturer dataProduction line + day serial number (5-digit)IIC code (6-digit, underlined)VW part number (10-digit)Type test number (4-digit)S442_126Engine control unitThe engine control unit checks all processes that are required to regulate the engine system. The engine control unit regulates the engine output data, like fuel injection quantity, fuel injection time etc. using the vehicle data it receives (engine speed, coolant temperature, accelerator pedal position etc.).S442_14436 Combination valveIn the Polo 2010, the combination valve is mounted near the fuel filter. The combination valve has the task of preheating the fuel.FunctionCombination valve closedPlunger Engine return Tank returnEngine supply lineTank supply lineWhen cold starting, the return to the tank is closed by the plunger in the combination valve. Warm fuel from the engine return is mixed with cold fuel from the tank in the combination valve and is delivered to the engine again. Preheating the fuel in this way prevents the separation of paraffin and thus fuel filter blockages.S442_252 HousingEngine returnAs the engine temperature rises, the fuel temperature in the engine return line also rises. As a result, the plunger heats up together with the wax thermostatic element in the combination valve. The wax thermostatic element expands and presses the plunger upwards against the spring force.Spring S442_251 Wax elementCombination valve openVehicle returnOnce the operating temperature has been reached, the combination valve opens the return line to the tank. Cold fuel from the tank mixes with warm fuel from the engine return line and flows back into the fuel tank. This allows the fuel in the fuel tank to warm up at low temperatures.S442_250 Warm fuel Cold fuel37 System OverviewSensorsG28 Engine speed sender G40 Hall sender G79 Accelerator position sender G185 Accelerator position sender 2 G70 Air mass meter G62 Coolant temperature sender G83 Radiator outlet coolant temperature sender G31 Charge air pressure sender G42 Intake air temperature sender J285 Control unit in dash panel insert K83 Exhaust emissions warning lampK29 Glow period warning lamp K231 Diesel particulate filter warning lampG81Fuel temperature senderG247 Fuel pressure sender G212 Exhaust gas recirculation potentiometerG39 Lambda probe G450 Exhaust gas pressure sensor 1 G235 Exhaust gas temperature sender 1 G495 Exhaust gas temperature sender 3 G648 Exhaust gas temperature sender 4 F Brake light switchG476 Clutch position sender G581 Position sender for charge pressure positioner G336 Intake manifold flap potentiometer* G69 Throttle valve potentiometer G266 Oil level and oil temperature sender38 ActuatorsJ17 G6 Fuel pump relay Fuel system pressurisation pumpPowertrain CAN data busN30 N31 N32 N33Injector, cylinder 1 Injector, cylinder 2 Injector, cylinder 3 Injector, cylinder 4N290 Fuel metering valveN276 Fuel pressure regulating valve N75 Charge pressure control solenoid valveV157 Intake manifold flap motor*J623 Engine control unitJ338 Throttle valve moduleN18Exhaust gas recirculation valveJ533 Data bus diagnostic interfaceN345 Exhaust gas recirculation cooler change-over valveV178 Coolant circulation pump 2Z19Lambda probe heaterS442_067J179 Q10 Q11 Q12 Q13Automatic glow period control unit Glow plug 1 Glow plug 2 Glow plug 3 Glow plug 4* No function at present39 Functional Diagram50 30 15J317SSSJ519J17J179A G6 SQ10 Q11Q12 Q13J623N79 V17831G42G31G450S442_200 A G6 G31 G39 G42 G62 G70 G81 G83 G235 G336 G450 G495 Battery Fuel system pressurisation pump Charge air pressure sender Lambda probe Intake air temperature sender Coolant temperature sender Air mass meter Fuel temperature sender Radiator outlet coolant temperature sender Exhaust gas temperature sender 1 Intake manifold flap potentiometer* Exhaust gas pressure sensor 1 Exhaust gas temperature sender 3 G581 G648 J17 J179 J317 J519 J623 N30 N31 N32 N33 N276 N290 Position sender for charge pressure positioner Exhaust gas temperature sender 4 Fuel pump relay Automatic glow period control unit Voltage supply relay Onboard supply control unit Engine control unit Injector, cylinder 1 Injector, cylinder 2 Injector, cylinder 3 Injector, cylinder 4 Fuel pressure regulating valve Fuel metering valve40 50 30 15S G70 G39 Z19SN30N31N32N33 N276 N290J623V157 G23531G336G581G495G648G83G62G81S442_202 Q10 Q11 Q12 Q13 S V157 V178 Z19 Glow plug 1 Glow plug 2 Glow plug 3 Glow plug 4 Fuse Intake manifold flap motor* Coolant circulation pump 2 Lambda probe heater* No function at presentColour code/legend = input signal = output signal = positive = earth = powertrain CAN data bus41 Functional Diagram50 30 15SSSG185 N75 N345 F G476G79KJ623N1831G212G247J338G69G40G28S442_204F G28 G40 G69 G79 G185 G212 G247 G476 J338 J623 N18 N75 N345Brake light switch Engine speed sender Hall sender Throttle valve potentiometer Accelerator position sender Accelerator position sender 2 Exhaust gas recirculation potentiometer Fuel pressure sender Clutch position sender Throttle valve module Engine control unit Exhaust gas recirculation valve Charge pressure control solenoid valve Exhaust gas recirculation cooler change-over valveK S 1 2Diagnostic connection Fuse CAN data bus CAN data busColour code/legend = input signal = output signal = positive = earth = powertrain CAN data bus42 ServiceSpecial toolsDescription T10402 Puller Tool Application For removal of injectors (piezo injectors)S442_036T10403 Transportation lockFor locking decoupling element of exhaust systemS442_03843 Test YourselfWhich answers are correct? One or several of the answers could be correct.1.What output versions of the 1.6l TDI engine are available? a) 44kW, 55kW, 81kW b) 50kW, 70kW, 90kW c) 55kW, 66kW, 77kW2.What is a flexi belt? a) A flexible, stretchable poly V-belt b) A tensioned poly V-belt c) A poly V-belt stretched with a tensioner3.Where is the exhaust gas recirculation module fitted? a) On the intake side, on the intake manifold b) On the exhaust side, on the cylinder head c) On the underbody, near to the fuel tank44 4.What components belong to the high-pressure pump? a) Pre-supply pump, high-pressure pump unit, rail b) Pre-supply pump, fuel metering valve, high pressure pump unit c) High-pressure pump unit, rail, injector5.What is the task of the fuel pressure sender G247? a) The fuel pressure sender measures the fuel pressure in the rail. b) The fuel pressure sender measures the fuel pressure in the pre-supply pump. c) The fuel pressure sender measures the fuel pressure in the fuel return line.Answers 1. c); 2. a); 3. b); 4. b); 5. a)45 Notes46 47 442© VOLKSWAGEN AG, Wolfsburg All rights and rights to make technical alterations reserved. 000.2812.22.20 Technical status 06.2009 Volkswagen AG After Sales Qualifizierung Service Training VSQ-1 Brieffach 1995 D-38436 Wolfsburg❀ This paper was manufactured from pulp that was bleached without the use of chlorine.