TECHNICAL DOCUMENTATION
SSP 406 DCC Adaptive Chassis Control

This PDF is currently unavailable.
Read document text
Service TrainingSelf-study Programme 406DCC Adaptive Chassis Control Design and FunctionS406_002The rule for suspension systems has always been that increasing sportiness compromises the ride. In this new system – the DCC adaptive chassis control, the suspension constantly adjusts itself to the road conditions, the driving situation and the driver’s requirements. Adjustable shock absorbers are required to make this possible.The steering support is also adjusted in addition to the damping. The DCC adaptive chassis control is being used for the first time at Volkswagen in the Passat CC. This self-study programme shall explain how the DCC adaptive chassis control system works in detail.The self-study programme shows the design and function of new developments. The contents will not be updated.For current testing, adjustment and repair instructions, refer to the relevant service literature.NEWImportant Note2ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Basics of damping system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjustable shock absorber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Map for adjustable shock absorber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4 5 7System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 DCC adaptive chassis control system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Overview of components used in vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 System link to brakes and steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 System overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Shock absorber for DCC adaptive chassis control . . . . . . . . . . . . . . . . . . . . . 14 Adjustment valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Electrics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electronically controlled damping control unit J250 . . . . . . . . . . . . . . . . . . . . Vehicle level senders G76, G78, G289 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Body acceleration senders G341, G342, G343 . . . . . . . . . . . . . . . . . . . . . . . . Functional diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 20 21 24 26Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Test Yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .303IntroductionBasics of damping systemThe shock absorbers have the task of quickly reducing the vibration energy of the body and road wheel oscillations.Suspension configurationLow damping levelThe shock absorbers prevent the body rocking due to bumps in the road and stop the wheels bouncing out of control on the road surface. Furthermore the body is also stabilised by the damping forces during dynamic manoeuvres. An even greater damping effectiveness is achieved with adjustable shock absorbers since the current driving situation can be taken into consideration more efficiently. The electronically controlled damping control unit determines within milliseconds what level of damping is required at which wheel and adjusts the shock absorber accordingly. The damping level is the rate at which the vibrations are reduced. This is dependent on the damping force of the shock absorber and the size of the sprung masses. Increasing the sprung mass reduces the damping level, which means the vibrations are reduced more slowly. Reducing the sprung masses increases the damping level.Spring travelThe compression cycle and extension cycle are features of the suspension. The damping force in the compression cycle is normally lower than in the extension cycle.TimeS406_005High damping levelSpring travelTimeS406_0044Adjustable shock absorberAn adjustable shock absorber using a twin-tube design is employed for the DCC adaptive chassis control. The piston runs in chamber 1. There is an additional gas cushion in chamber 2.Piston rodShock absorber shown during extension cycleGuide/sealOverflowRing channel CylinderDe-foaming coilPiston valveGas cushionChamber 1 PistonChamber 2Base valve Base plateS406_031Adjusting valve5IntroductionFunction in extension and compression cycleCheck valves on the piston and base plate cause the oil to flow in the directions shown in the diagram during extension and compression. The oil is fed to the adjustment valve through the ring channel and it flows in the same direction (uniflow) during extension and compression. The oil flows back into chamber 2 from the adjustment valve. The adjustment valve determines the pressure in chamber 2 and thus the damping. The cylinder contains chamber 2. It is only partly filled with oil. There is a gas cushion with a de-foaming spiral above the oil filling. Chamber 2 is used to compensate changes in the oil volume. The oil flow is controlled by the damping valve units on the piston, on the chamber base and in the adjustment valve. They consist of a system of flat springs, coil springs and valve bodies with oil flow ports.Extension cycleDe-foaming coil Ring channel Chamber 2Compression cyclePiston valveS406_045 Base valve Adjustment valve Adjustment valveS406_046During the extension cycle, the oil flow is controlled by:● ● ●During the compression cycle, the oil flow is throttled by:● ● ●the adjustment valve, the base valve and to a limited extent the piston valve.the adjustment valve, the piston valve and to a limited extent the base valve.6Map for adjustable shock absorberCompared with a conventional shock absorber with fixed map, the adjustable shock absorber has an adjustable characteristic curve within a map.Conventional shock absorberAdjustable shock absorberDamping forceExtension cycleDamping force Characteristic curveExtension cycle MapForceForceCompression cycle S406_013Compression cycle S406_014Conventional shock absorbers have a characteristic curve that helps define the driving properties of the vehicle. Defining this characteristic curve is the result of the suspension configuration that is carried out for each vehicle. This depends, among other things, on the weight distribution of the vehicle, the engine, the vehicle character and the axle kinematics.The damping characteristic curves of the adjustable shock absorber can be modified by varying the current supplied to the adjustment valve. This creates a map. This adjustment is made in all driving modes (“Normal”, “Sport” and “Comfort”). Depending on the current driving situation, the shock absorber rates are adjusted within the specified map even when a driving mode is selected.In “Fail Safe” mode, the adjustment valves are not powered and the shock absorbers are thus operated with a defined characteristic curve.7System descriptionDCC adaptive chassis control systemThe adjustable shock absorbers are regulated by a control unit that adjusts the damping according to a control algorithm developed by Volkswagen. Depending on the input signals, the whole map of the adjustable shock absorbers is used. This control algorithm can also be switched from “Normal” mode to “Sport” or “Comfort” mode using the button and thus adjusted to customer requirements. The system can be adjusted when the vehicle is stationary or travelling. The DCC adaptive chassis control is always active. It is an intelligent automatically controlled system that adjusts the vehicle shock absorbers depending on● ●Notes:●●the road surface, the respective driving situation (e.g. braking, accelerating and cornering) and the driver’s●●The driving mode last activated is also still active after the ignition is switched OFF/ON. The driving mode can be switched over while the vehicle is stationary or on the road. The adjustment valves are not powered when the vehicle is stationary.requirement. Thus the driver always has the ideal suspension setting. Driver requirement● ●Road surface Driving situationJ250Calculated current for shock absorber adjustment(algorithm)S406_0478Selectable DCC modesThe DCC mode can be set by the driver depending on individual requirements using the button to the right of the gear lever. Press the button until you obtain the required setting. You can repeat this as often as required. The modes are always switched through in the order “Normal” – “Sport” – “Comfort”.“Normal” mode“Normal” mode is active when neither the “Comfort” nor “Sport” labels on the button are illuminated yellow. This setting provides an overall balanced, but still dynamic driving feel. It is well suited for everyday use.S406_037“Sport” modeThis mode is active when the “Sport” label is illuminated yellow in the button. This setting gives the vehicle sporty handling with a harder basic configuration. The steering is also set sporty and the chassis damping is stiffer. This setting allows a particularly sporty driving style.“Comfort” modeThis mode is active when the “Comfort” label is illuminated yellow in the button. This setting leads to a comfort-oriented, softer basic configuration of the chassis damping. It is suitable, for example, for driving on bad roads and for long journeys. The differences in the modes are noticeable from the varying hardness of the basic damping settings. They are superimposed by higher damping force requirements due to the driving situations.S406_038S406_0399System descriptionOverview of components used in vehicleThe diagram is a simplified depiction of the components in the DCC adaptive chassis control system and their relationships (the senders each have a separate connection to the electronically controlled damping control unit J250 – they are combined for each axle in the diagram for reasons of simplicity).Legend E387 G76 G78 G289 G341 G342 G343 J104 J250 J285 J500 J533 N336 N337 N338 N339 Shock absorber damping adjustment button Rear left vehicle level sender Front left vehicle level sender Front right vehicle level sender Front left body acceleration sender Front right body acceleration sender Rear body acceleration sender ABS control unit Electronically controlled damping control unit Control unit in dash panel insert Power steering control unit Data bus diagnostic interface Front left shock absorber damping adjustment valve Front right shock absorber damping adjustment valve Rear left shock absorber damping adjustment valve Rear right shock absorber damping adjustment valveLegendInput signal Output signal CAN data busS406_02110System link to brakes and steeringIn the DCC adaptive chassis control, information is exchanged between the electronically controlled damping control unit and the associated networked control units via the CAN data bus. The system overview shows an example of the information that is provided via the CAN data bus or is received and used by the networked control units.Shock absorber damping adjustment button E387Control unit in dash panel insert J285 Display of DCC mode on screenElectronically controlled damping control unit J250 Powering adjustment valves Control of function lamps in the buttonData bus diagnostic interface J533 Interface function for CAN data bus system Transmits the DCC mode to the CAN data busCAN data busVehicle level senders G76, G78, G289 Wheel compression and extension travelPower steering control unit J500 Adjustment of power steering to DCC modeBody acceleration senders G341, G342, G343 Body vertical acceleration Additional information, e.g.: - Gearbox control unit - Engine control unit - ABS/ESP control unit - Driver assistance systems, e g. ACCInformation that is evaluated by control unit J250 Information that is supplied by control unit J250Forwarding information to the CAN data bus CAN data bus11System descriptionSystem overviewSensorsAdditional information, e.g.: Accelerator pedal position (required driver moment) ● Steering angle sensor ● Brake pressure●Shock absorber damping adjustment button E387Front left body acceleration sender G341 Front right body acceleration sender G342Data bus diagnostic interface J533Rear body acceleration sender G343Front left vehicle level sender G78 Front right vehicle level sender G289Rear left vehicle level sender G76Power steering control unit J50012ActuatorsFront left shock absorber damping adjustment valve N336 Control unit with display in dash panel insert J285Front right shock absorber damping adjustment valve N337 Electronically controlled damping control unit J250Rear left shock absorber damping adjustment valve N338S406_012Rear right shock absorber damping adjustment valve N33913FunctionShock absorber for DCC adaptive chassis controlTwin-tube shock absorbers are used for the DCC adaptive chassis control. An electrically controlled adjustment valve mounted on the outside of the shock absorber regulates the damping force. By varying the current, the damping force of the active shock absorber setting can be adjusted within a few milliseconds by the adjustment valve. The 3 vehicle level senders provide signals that are required to calculate the necessary shock absorber setting together with the signals from the 3 body acceleration senders. The maps for the respective shock absorber setting are stored in the electronically controlled damping control unit J250.Shock absorber shown during extension cycleAdjustable shock absorberRing channelIn the diagram, the ammeter is shown simply to help explain the current supplied to the adjustment valve (ammeter in “Normal” mode).Chamber 2 AmmeterA fixed current is not used to control the system within the “Normal”, “Sport” and “Comfort” modes, instead a range of values are used (see yellow-coloured area in ammeter). The following diagrams for the possible adjustment valve modes simply show the centre position of the ammeter needle within the yellow-coloured area.S406_025 Adjustment valve14Adjustment valveThe adjustment valve is mounted on the side of the shock absorber so that oil from the shock absorber ring channel flows to the valve. The oil supplied from the adjustment valve is sent to chamber 2 of the shock absorber. The valve is adjusted by applying a current to the coil (0.24 A to max. 2.0 A) and the resulting changes inside the adjustment valve. Depending on the control position of the adjustment valve, the oil flowing from the shock absorber moves the main slider to a corresponding horizontal position so that a specific amount of oil can flow back to the shock absorber through the return channel. The main slider position is achieved by setting a differential pressure (compared with the pressure of the oil flowing from the shock absorber) in the inner control volume. The differential pressure is set by pre-tensioning the gap cross-section between the pressure head and control plate. If the pre-tension becomes greater, for example, the amount of oil flowing away centrally through the main slider and further through the ring gap and control channel is reduced, the pressure increases in the inner control volume and the main piston can only be moved slightly to the right. This changes the damping behaviour towards “hard”. If the pre-tension becomes smaller, the system behaves in the opposite way. The damping behaviour is changed towards “soft”.The greater the current applied, the harder the damping.Electrical connection Control plate Internal control volume Coil Main piston Return channel Armature To shock absorber Push rod From shock absorber Fail-safe valveTo shock absorberPressure headPressure plate Return channel Control channel Ring gap S406_05015FunctionAdjustment valve in “Normal” modeIn “Normal” mode, a current in a middle range between 0.24 A and 2.0 A is supplied to the coil. The armature is moved together with the push rod and pressure head and is pre-tensioned slightly. The oil flowing from the shock absorber presses the main piston to a horizontal centre position so that a medium quantity of oil can leave again via the return channel and be fed back to the shock absorber. This is achieved by setting a medium pre-tension between the pressure head and control plate. The differential pressure is also set accordingly in the internal control volume and the position of the main piston is set in a horizontal middle position. The damping behaviour is thus between “soft” and “hard”.Electrical connection Control plate Internal control volume Coil Main piston Return channel Armature To shock absorber Push rod From shock absorberTo shock absorberPressure headPressure plate Return channel S406_04416Adjustment valve in “hard”In “hard”, the coil is powered in a range up to a max. of 2.0 A. The armature is pressed to the left together with the push rod and pressure head with maximum pre-tensioning to the left. As a result, there are smaller gap cross-sections between the control plate and pressure head compared with “Normal” mode. The differential pressure in the internal control volume increases and the main piston sets itself in its horizontal position so that a lower oil quantity flows back via the return channel to the shock absorber than in “Normal” mode. This changes the damping behaviour towards “hard”. This is a typical state of the adjustment valve for a considerably dynamic manoeuvre.Electrical connectionControl plate Internal control volume Main piston Armature To shock absorber Push rod From shock absorber CoilTo shock absorberPressure headReturn channelS406_02817FunctionAdjustment valve in “soft”In “soft”, the magnet is powered with 0.24 A, for example, and has less pre-tensioning together with the push rod and pressure head. The pressure head moves the control piston to the left by the same amount and releases the ring gap only in a slightly reduced cross-section. The oil flows via this gap and the subsequent control channel back to the shock absorber. The gap cross-section between the control plate and pressure head increases with this slightly lower pre-tensioning of the pressure head. The differential pressure in the internal control volume drops. The main piston thus sets itself in its horizontal position so that a greater amount of oil flows back via the return channel than in “hard”. This changes the damping behaviour towards “soft”. This is a typical state of the adjustment valve for a considerably dynamic manoeuvre.Control piston Control plate Internal control volume Main pistonElectrical connectionCoilArmature To shock absorber Push rod From shock absorberTo shock absorberPressure headReturn channel Control channel Ring gapS406_02918Adjustment valve in “Fail Safe”If a shock absorber, at least two sensors or the electronically controlled damping control unit J250 fail, “Fail Safe” mode is set. In “Fail Safe” mode, the shock absorbers are not powered and the vehicle behaves as if fitted with conventional shock absorbers. The armature moves together with the push rod and pressure head to the right until it rests against the valve housing. The control piston also moves and closes the direct access to the ring gap. The oil now opens the fail-safe valve and flows via the control channel to the shock absorber.Electrical connection To control channel Fail-safe valve Main piston CoilArmature To shock absorber Push rod From shock absorber Valve housing To shock absorber Pressure headS406_027 Control channel Ring gap Control piston19ElectricsElectronically controlled damping control unit J250The control unit J250 is in the boot on the right-hand side behind the panelling (Passat CC). It evaluates the signals from the vehicle level senders G76, G78, G289 and the body acceleration sender G341, G342, G343 and constantly calculates the respective optimum current for the four shock absorbers taking the road, driving situation and driver requirement into consideration. It adjusts the shock absorbers within milliseconds using a controlled current (approx. 0.24 A … 2.0 A).S406_016 Electronically controlled damping control unit J250Indications in dash panel insertS406_032The suspension setting that the driver selects manually using the shock absorber damping adjustment button E387 is displayed in the dash panel insert. The setting/display last selected is available when the vehicle is started.20Vehicle level senders G76, G78, G289The vehicle level senders are so-called turn angle sensors. They are all fitted near to the shock absorbers and are connected to the traverse links via coupling rods. The wheel spring travel is forwarded to the sensors from the movement of the traverse links on the front and rear axle and on the coupling rods and converted into an angle of rotation. The turn angle sensor used works with static magnetic fields and uses the Hall principle. The signal output supplies a PWM signal (pulse-width modulated signal) proportional to the angle for shock absorber control.The three level sensors are identical; only the mountings, the coupling rods and kinematics are specific to the sides and axles.Vehicle level sender − front axle (right)Vehicle lever sender − rear axle (left)S406_019 Coupling rod Wishbone Rear left vehicle level sender G76 Wishbone S406_020Front right vehicle level sender G289Coupling rod21ElectricsDesignThe sender is set up in a two-chamber system. On one side (1st chamber), there is the rotor and, on the opposite side, (2nd chamber) the circuit board with stator. The rotor and stator are each fitted so they are sealed. The rotor consists of a non-magnetised stainless steel shaft in which a rare-earth magnet is glued. Rareearth magnets are used where high magnetic field strengths in conjunction with the smallest possible dimensions are needed. The rotor is connected to the coupling rod by the operating lever and is also driven by it. The rotor is mounted in a radial shaft seal in the operating lever. This protects the construction from the elements. The stator consists of a Hall sensor that is located on a circuit board. The circuit board is moulded in a PU mass (PU = polyurethane) and is thus also protected against external influences.Operating leverBearingRotor Radial shaft sealMounting bush for connecting coupling rodMagnet Connection contactsS406_007 Chamber 1 Circuit board with statorChamber 2 (PU mass)22FunctionThe magnetic flow is transferred and amplified using the Hall plates. Unlike conventional Hall senders, these elements deliver special sine and cosine signals. In the chip on the circuit board, the signals are converted so that the level changes of the body are recognisable for the electronically controlled damping control unit J250.Rotor magnetRotation of rotor (chamber 1)S406_008Chip on the circuit board with integrated stator (chamber 2)23ElectricsBody acceleration senders G341, G342, G343The body acceleration senders measure the vertical acceleration of the body.Body acceleration sender – front axleThe front left body acceleration sender G341 and front right body acceleration sender G342 are mounted on the body at the top next to the shock absorbers.S406_017 Front left body acceleration sender G341Body acceleration sender — rear axleThe rear body acceleration sender G343 is mounted at the top next to the left-hand rear shock absorber.S406_018 Rear body acceleration sender G34324Design and functionThe body acceleration senders work according to the capacitive measuring principle. An elastic mass m oscillates between capacitor plates as a middle electrode that pulls the capacities of capacitors C1 and C2 opposite the rhythm of their oscillation. The plate spacing d1 of one capacitor is increased by the amount that spacing d2 in the other capacitor is reduced. This changes the capacities of the individual capacitors.Capacitive measuring principle of the acceleration sendersS406_009An electronic evaluation system delivers an analogue signal voltage to the electronically controlled damping control unit J250.Sender measuring range The measuring range of the sender is ± 1.6 g. g = measurement for the acceleration 1 g = 9.81 m/sec225ElectricsFunctional diagramE387 G76 G78 G289 G341 G342 G343 J104 J250 J285 J500 J519 J533 K189 Shock absorber damping adjustment button Rear left vehicle level sender Front left vehicle level sender Front right vehicle level sender Front left body acceleration sender Front right body acceleration sender Rear body acceleration sender ABS control unit Electronically controlled damping control unit Control unit in dash panel insert Power steering control unit Onboard supply control unit Data bus diagnostic interface Shock absorber damping adjustment warning lamp Button illumination bulb Front left shock absorber damping adjustment valve Front right shock absorber damping adjustment valve Rear left shock absorber damping adjustment valve Rear right shock absorber damping adjustment valveL76 N336 N337 N338 N339Input signal Output signal Positive Earth CAN data bus26S406_01027ServiceWhat happens when …a shock absorber fails? If there is a short-circuit or interruption of an adjustment valve, the system immediately switches to “Fail Safe”. The shock absorber symbol in the button flashes to indicate the fault. The vehicle behaves like a vehicle with conventional damping.-the sensors fail?If only one sensor fails, a substitute signal is calculated from the other working sensors. The system is still capable of functioning. If two or more sensors fail, the system will be switched off in stages. The shock absorber symbol on the button flashes at a rate of 1 Hz for 100 milliseconds.the electronically controlled damping control unit J250 fails?The control unit J250 needs to be reprogrammed via SVM (Service Versions Management).a shock absorber is replaced and adjustment is required?A basic set-up needs to be carried out (teaching the wheel travel sensors at the lower limit).the steering fails?The DCC adaptive chassis control still continues to operate.28Special features:End position damping: The end position damping is used to avoid end position forces and end position noises in the extension and compression cycle. Load recognition: The load recognition is used to determine the body mass of the vehicle as an input variable. This is calculated by evaluating the vehicle level sender and is supplied to other systems on the CAN data bus.Brake test stand: The system obtains the wheel speed information on the brake test stand. The body acceleration cannot be calculated, however. Therefore the system always regulates in the range comfort = soft and thus presumes the road conditions are good.Shock absorber test stand: On a shock absorber test stand, the system receives information neither from the vehicle level senders, the body acceleration sensors nor wheel speed information. Therefore the adaptive chassis control presumes the vehicle is stationary. The shock absorbers are not powered and can therefore be checked normally.29Test Yourself1. What is the switching order of the damping adjustment button? a) Sport, Normal, Comfort b) Normal, Sport, Comfort c) Comfort, Fail Safe, Normal2. What information is evaluated by the electronically controlled damping control unit J250? a) Adjustment of the steering assistance, pressure from the brake pressure sender b) Engine temperature, accelerator pedal position, vehicle level sender c) Compression and extension travel of wheels, vertical acceleration of the body, damping adjustment button3. What information has an influence on the power supplied to the adjustment valves? a) Engine temperature, wheel speeds and road condition b) Driving situation, customer requirement and road condition c) Tread depth of tyres, engine load and loading301. b; 2. c; 3. b Answers:Notes31406© VOLKSWAGEN AG, Wolfsburg All rights and rights to make technical alterations reserved. 000.2812.06.20 Technical status 06.2008 Volkswagen AG Service Training VSQ-1 Brieffach 1995 38436 Wolfsburg❀This paper was manufactured from pulp that was bleached without the use of chlorine.