TECHNICAL DOCUMENTATION

SSP 469 The Touareg 2011 Chassis

PDFEN60 pages4 MB
SSP 469 The Touareg 2011 Chassis - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingSelf-study Programme 469The Touareg 2011 Chassis and Four-wheel Drive Concept Design and Function The Touareg 2011 is a completely new development. It combines the sporty performance of a car with improved off-road capabilities. This makes it a luxury-class off-road vehicle that unites the requirements of on-road and off-road driving even more perfectly. The chassis has been optimised not just to improve the performance, but also to reduce the weight of components. The chassis, which is up to 47kg lighter compared with the previous model, makes a substantial contribution to reducing fuel consumption and carbon dioxide emissions.S469_001The self-study programme portrays the design and function of new developments. The contents will not be updated.For current testing, adjustment and repair instructions, refer to the relevant service literature.Important Note2 ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Front and rear axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Air suspension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Braking system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Hybrid electrical components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Wheels and tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Tyre pressure monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Transfer box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Test yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 563 IntroductionTouareg 2011 chassisThanks to its running gear tuning, the Touareg 2011 offers outstanding off-road qualities. However, it also guarantees maximum ride comfort on normal roads. The running gear therefore combines the following characteristics: Very good vibration and wheel/tyre comfort Low tendency to roll Agile performance High dynamic stability Very good off-road capabilities●Leather or wood steering wheel, with multifunction buttons as standard●ABS/ESP MK25 A-XT from Conti Teves●Front and rear anti-roll bars●Independent wheel suspension●Tyre pressure monitor, optional●Internally ventilated disc brakes (front and rear)●Double wishbone front suspension4 Thanks to the following measures, the chassis makes a considerable contribution to reducing fuel consumption and carbon dioxide emissions: Chassis weight reduced by up to 47kg Low-rolling resistance tyres Regulated power steering pumps●Electromechanical parking brake●4XMOTION with selectable central and axle differential lock, optional●4MOTION with transfer box●Double wishbone rear suspension with split upper wishboneS469_065●Stationary vehicle management with HILL HOLD and AUTO HOLD●Air suspension with closed-loop air supply and regulated damping, optional5 IntroductionFour-wheel drive conceptThe Touareg has the technical prerequisites for excellent off-road capability. Short body overhangs, ground clearance of up to 300mm, a fording depth of up to 580mm, a climbing ability of 100% (45°) with 4XMOTION, a lateral inclination of 35 degrees, the breakover angle and the axle articulation also make extreme off-road usage possible.●Climbing ability for 4XMotion33°●Breakover angle45°580mm●Fording depth6 Values for vehicles with steel suspension:● ●●Fording depth Ground clearance with sports suspension Breakover angle= 500mm = 222mm = 187mm = 22°The climbing ability for vehicles with transfer box is 31° (4MOTION).The values shown in the illustration apply to vehicles with air suspension.●Body overhangs33°33°35°●300mm●Dynamic lateral inclinationGround clearanceS469_0087 Front and rear axleFront axleThe front axle on the Touareg uses double wishbone suspension. This proven design allows large spring travel and good articulation of the axles on rough terrain. Using aluminium and omitting the upper wishbone mount has allowed the weight to be reduced by up to 27kg compared with the previous model. The decoupled subframe is used to mount the front axle differential and the steering box. On the V8 and hybrid versions of the vehicle, the lower wishbone and the swivel bearing are made from aluminium.Spring damperFront axle differentialWheel bearing housingSubframeUpper wishboneAnti-roll barSwivel bearingLower wishbone S469_0108 Rear axleThe rear axle on the Touareg also uses double wishbone suspension. The lower wishbone and the track rod are made from steel sheet and the upper wishbone from aluminium. The damper cross member has been integrated into the body. The decoupled subframe of the rear axle uses a tube frame design. The following components are mounted on it: Upper and lower wishbone Track rod Rear axle differential A weight reduction of up to 20kg compared with the previous model has been achieved with the following measures: Lightweight hub carriers made from cast aluminium Rear lower wishbone and track rod weightoptimised and made from steel Weight-optimised wheel flange and weight-optimised wheel bolts Weight-optimised spring dampersUpper wishboneRear axle differentialSpring damperSubframeWheel flange Lower wishbone S469_0129 Air suspensionOverview of componentsFor the first time, the air suspension system on the Touareg 2011 is a closed system. The closed system has the following advantages compared with the open system:● ● ● ●Reduction of the storage volume required for the air system Air exchanged only between air spring dampers and pressure accumulator during normal regulation Clearly lower pressure difference during regulation Use of a smaller compressor that weighs less, runs quieter and consumes less powerAir supply unit Front axle air spring damperS469_021 Rear axle air spring damper Pressure accumulatorFurther features of the system: - Internal valves for damper adjustment (CDC valves) - 4 senders for vehicle level (level sensors) - 2 front body acceleration senders, accessible from engine compartment - 1 rear body acceleration sender integrated in control unit - Button on right of luggage compartment for lowering the rear end - Air capacity of strut approx. 2.5 litres - No tyre filler connection - Wheel acceleration sensors have been omitted. Their functions have been taken over by the level sensors. - Only one pressure accumulator with 6.2 litres capacity (omission of pressure accumulator in luggage compartment)10 OperationAdaptive suspension controlsThe adaptive suspension controls are located in the centre console behind the automatic gear selector lever. The vehicle level is set with the right-hand rotary switch and the dampers are adjusted with the thumb wheel in the centre. The LOCK button limits the maximum speed to approx. 70km/h at OFF ROAD level. This prevents the vehicle being lowered.Button for start/stop modeThumb wheel for damper adjustmentS469_032 Rotary switch for selecting gears and differentials Button for TCS and ESP Lock button Rotary switch for vehicle levelControls for lowering load sillThe Touareg with air suspension has controls in the luggage compartment for lowering the load sill. This allows you to lower and raise the tail of the vehicle for loading. This only works when the doors are closed. This prevents objects being trapped under the open doors. The rear end of the vehicle is lowered by up to 120mm in loading mode. It can be raised up to the level set with the rotary switch for vehicle level.RaiseS469_066Lower11 Air suspensionVehicle level adjustmentThe air suspension system allows you to adjust the vehicle ride height to the current driving situation. The ride height is set using the vehicle level adjustment switch (right-hand rotary switch). A ground clearance of 172mm to 300mm can be set. Lowering improves the road holding and reduces the air resistance. The level is automatically adjusted when specific speed limits are reached.Loading level At loading level (below 5km/h), the ride height is 147mm.S469_023 High-speed level At high-speed level (from 140km/h), the ride height is 172mm. From 190km/h, the vehicle is lowered again by 10mm.S469_025 Road level At road level (below 100km/h), the ride height is 197mm.S469_027 Off-road level At off-road level (below 40km/h), the ride height is 247mm.S469_029 X’tra level At X’tra level (below 25km/h), the ride height is up to 300mm.S469_03112 Bar indicator for vehicle levelThe selected vehicle level is displayed on the bar indicator in the centre display of the dash panel insert. If the vehicle height is changed, the bar indicator will flash until the selected level has been reached.Bar indicatorS469_090The display contents shown correspond to the infotainment system with German system setting and serve merely as an example. Please refer to the corresponding operating manuals for the text contents shown on the display in the relevant national languages.Damper controlThe Touareg damper control increases the ride comfort in all driving situations.Three different damper settings can be selected with the rotary switch for damper adjustment in the adaptive suspension controls:●●●Normal - balanced configuration for everyday usage Sport - sporty configuration for sporty driving style Comfort - comfort-oriented configuration for driving on bad roads and long distancesS469_034If you drive in a sporty style, e.g. with fast cornering, the damping is automatically set to “Sport” regardless of the selected setting. The position of the rotary switch for damper adjustment is not changed in this case. If you set the dampers to “Sport” at road level, the vehicle will also be lowered to the high-speed level at speeds below 125km/h.13 Air suspensionAir spring dampersAir suspension struts with air spring dampers, which have external air suspension springs, a hanging roller piston and electronically controlled dampers, are used on the front axle and the rear axle. The special features of these air spring dampers are:● ●●Electrically adjusted damper with internal valves, Reversal of current: - at a current of 0mA, the dampers are hard (fail-safe function), - at a maximum current of 1800mA, the dampers are soft, The residual pressure retention valves have been replaced by pressure retention valves.Pressure retention valve Additional springExternal guideDamper piston rodValve for damper adjustment (CDC valve)Bellows (protective bellows)S469_10414 Pressure retention valveThe pressure retention valve replaces the residual pressure retention valve. The advantage of this is that the damper is always sealed when the line is disconnected and it is always open when the line is connected.S469_112Pressure retention valveS469_106 Open pressure retention valve when line is connectedS469_108 Closed pressure retention valve when line is not connectedFitting marking 1The air line has two fitting markings. Please follow the instructions in ELSA when fitting the air line.Fitting marking 2S469_11015 Air suspensionDamper controlThe damper control system detects the road conditions or the movement of the vehicle via four vehicle level senders and three body acceleration senders. The characteristic curves of the individual vibration dampers are adjusted in accordance with the calculated damping requirement. The dampers work here as supporting components during the compression and extension cycles. The damping force can be adjusted on the basis of a map using the proportional valve (internal CDC valve) built into the vibration damper. It is therefore possible to adjust the damping force to the driving situation and the road conditions within milliseconds. In principle, the system tries to adjust the damping force using the “sky-hook control strategy”. The damper is adjusted in relation to the vertical acceleration of the wheels and the vehicle body. Ideally, damping is regulated so that the vehicle body “hangs from the sky on a hook” and floats above the road with almost no disruptive movements. In this way, maximum ride comfort is achieved.The continuous damper regulation is based on vibration dampers, whose characteristic curves are electrically adjusted. These vibration dampers are integrated in the air spring dampers.Characteristic curves for front axle damping force600Compression cycle500Extension cycle50mA 600mA1200mADamping force [dN]400 1800mA 30050mA 600mA 1200mA 1800mA2001000 2000S469_0921500 1000 500 0 500 1000 1500 2000Damper speed [mm/s]The current is reversed compared with the previous model. Soft suspension is achieved with large control currents (maximum 1800mA current). Hard suspension is achieved with small control currents. At a current of 0mA, the dampers are hard (fail-safe function).16 Valve for damper adjustmentThe damping force of the CDC two-pipe gas damper can be adjusted across a wide range via an electrically controlled valve that is integrated into the damper. By changing the current to the solenoid, the flow of oil through the valve for damper adjustment (CDC valve) can be adjusted within a few milliseconds. In this way, the damping force is adapted to the current requirements. Oil flows through the CDC valve in the same way both in the compression and extension directions. This is achieved by the piston and base valve functioning as a non-return valve. The four vehicle level senders supply signals that, together with the signals from the body acceleration senders, are required to calculate the required damper setting. Thanks to the fast recognition and control between the compression and extension cycle, it is possible to ensure that only the damping force required for the current driving situation is set. The maps related to driving situations are stored in the adaptive suspension control unit.In certain vehicle-dynamics conditions (for instance, longitudinal and/or transverse dynamics), the adaptive suspension control system is temporarily deactivated and the damper control is hardened depending on the situation.17 Air suspensionAir supply unitThe air supply unit is mounted at the front right as a compact unit on the underbody. It is protected from dirt by a plastic cover with ventilation holes. The air for the compressor is supplied via the air filter in the engine compartment. The air is drawn in and cleaned via the silencer/filter. The air is released via a separate line. The air supply unit consists of: the compressor unit with electric motor, compressor, air drier, silencer with air filter, pneumatic release valve with maximum pressure limitation (pressure limiting valve), the solenoid valve block with the control valves for each air spring damper and the solenoid release valve.The pressure accumulator is connected directly to the compressor via a non-return valve. Since the air supply in the Touareg 2011 operates as a closed system (closed-loop air supply) and thus the air is pumped from the accumulator into the air springs to raise them and from the springs back into the accumulator to lower them, the average pressure to be overcome is smaller than with an open air supply. This has allowed the compressor to be made smaller, lighter and quieter. However, it is necessary to run the compressor for most regulating operations.Compressor Air drierVibration insulator Solenoid valve blockVibration insulatorS469_028 To silencer/filter Electric motor18 Pressure accumulatorThe pressure accumulator is used to supply a pilot pressure for faster regulating operation. Upon lowering of the dampers, it is used as an energy accumulator in order to not release air into the environment. The pressure accumulator is filled if the pressure in the system has changed due to leaks or temperature differences. If the pressure in the system rises above a certain value due to an increase in temperature, the air is released to the outside. The pressure accumulator capacity is 6.2 litres. The system (air suspension system) is refilled in service with nitrogen using the connection provided on the pressure accumulator.Filling the pressure accumulatorThe pressure accumulator is filled with the vehicle diagnosis, testing and information system VAS 5051B. There are two possibilities.● ●Filling with nitrogen Filling with air via the compressorWhen filling via the compressor, the combustion engine must run for approx. 45 minutes. The special tools VAS 6629 and T10157, as shown in the diagram, need be fitted on the pressure accumulator when filling with nitrogen.S469_128 Nitrogen filling set for air suspension struts (VAS 6629)Pressure accumulator Adapter (T10157)19 Air suspensionSensorsVehicle level senders G76, G77, G78, G289The four vehicle level senders are so-called rotational angle sensors and are identical. With the aid of coupling rods, the level changes of the vehicle body are measured and converted into angle changes. The rotational angle sensor works according to the induction principle. The signal output supplies a PWM signal (pulse-width modulated), which is proportional to the angle, for the adaptive suspension control. Furthermore they take on the function of the discontinued wheel acceleration sensors. These displacement signals are used by the adaptive suspension control unit to calculate the direction and speed at which the struts move in relation to the body.S469_094 S469_098 Coupling rod Vehicle level sender front axleBody acceleration senders G341, G342, G343The senders for the body acceleration measure the vertical acceleration of the body and send these signals to the adaptive suspension control unit.Further information on the sensors can be found in self-study programme no. 275 “The Phaeton - Air Suspension with Controlled Damping”.Body acceleration senderS469_11420 Air suspension system componentsPneumatic diagram12 18 19 7 4 8 9 10 11 16 13 14 151732 1 6 5 S469_004Legend 1 2 3 4 5 6 7 8 9 Compressor V66 Air drier Throttle non-return valve Change-over valve Change-over valve Pressure accumulator Environment valve Rear left suspension strut valve N150 Rear right suspension strut valve N151 10 11 12 13 14 15 16 17 18 19 Front left suspension strut valve N148 Front right suspension strut valve N149 Rear left suspension strut Rear right suspension strut Front left suspension strut Front right suspension strut Pressure sensor Pressure relief valve Intake Release lineVehicle jack modeOn vehicles with adaptive suspension, the vehicle jack mode needs to be activated when a wheel is changed or the vehicle is raised on a lifting platform. This deactivates regulation of the air suspension and suppresses adjustment of the air suspension dampers when the vehicle is raised.Switching on● ● ● ●Switching off● ●Vehicle stationary Ignition on Parking brake activated Press LOCK button for longer than 5 secondsDrive faster than 5km/h or press Lock button for longer than 5 secondsWhen the vehicle jack mode is activated, the previously selected level is stored and an indication appears in the dash panel insert.21 Brake systemOverview of componentsThe Touareg 2011 has a dual-circuit braking system with one braking circuit acting on the front brakes and one braking circuit acting on the rear brakes.S469_116Brake servoThe Touareg has a 9"/10" tandem brake servo.Brake light switchThe brake light switch is mounted on the brake master cylinder. It operates according to the Hall principle. Since the brake light switch now only has one Hall sensor, the pressure sensor in the ESP control unit supplies a substitute signal.S469_118S469_12022 Front brakesBrembo brake calipers are used for the front wheel brakes on the Touareg. They are made of aluminium and have a monoblock design. The brake discs are internally ventilated.S469_018Engine V6 FSI and TDI engine V8 and hybrid enginePiston Steel swivel bearing with 4-piston brake caliper Aluminium swivel bearing with 6-piston brake caliperBrake disc size Ø 330 x 32mm Ø 360 x 36mmRear brakesThe rear brakes on the Touareg are high-performance brakes with internally ventilated brake discs measuring Ø 330 x 28mm. The aluminium fixed caliper has four brake pistons. On the Touareg 2011, disc brakes combined with an electromechanical parking brake are being used for the first time. A dual-servo drum brake is integrated in the brake disc.S469_020The function of this electromechanical parking brake is explained over the next few pages.23 Brake systemElectromechanical parking brakeOverviewRear wheel brake actuators These are integrated in the dualservo drum brakes as electromechanical actuators.ESP control unitControl unit for electromechanical parking brake Located in the side panel at the rear right. All control and diagnosis tasks of the electromechanical parking brake are performed here.S469_033Electromechanical parking brake warning lamp K213 Located in the dash panel insert. During a hydraulic braking operation, it lights up green and, when the parking brake is applied, it lights up red.Button for electromechanical parking brake Used to activate or deactivate the electromechanical parking brake. This button is located on the left of the automatic gear selector in the centre console.AUTO HOLD button This button is used to switch the AUTO HOLD function on and off. This button is located on the left next to the automatic gear selector in the centre console.24 Rear wheel brake actuatorsThe electromechanical parking brake operates with dual-servo brakes, in which drum brakes are integrated into the rear disc brakes. The drum brakes on the rear wheel are operated via the two brake actuators, which are electromechanical. The brake actuator converts the command “apply parking brake” into a force with the aid of the electric motor, multistage gear unit and the spindle actuator. The brake shoes are pushed apart and thus pressed against the inside of the brake drum.DesignBrake shoesBrake actuatorElectric motorMultistage gear unitSpringsSpindle actuatorS469_136 Adjusting screwBrake shoe mountingThe adjusting screw is used to set a defined distance between the brake drum and brake shoes.S469_148A basic setting needs to be carried out after removing and fitting the brake shoes. Please refer to ELSA for further information.25 Brake systemParkingThe electric motor of the brake actuator is powered. The rotary movement of the motor is converted into linear movement of the brake shoe mountings via the multistage gear unit and the spindle actuator. The brake shoes are pushed apart and pressed against the inside of the brake drum by the brake shoe mountings being moved against the force of the two springs.S469_126 S469_022ReleasingThe electric motor of the brake actuator is powered. The brake shoe mountings move in opposite directions. No more force is applied to the brake shoes. The springs pull the brake shoes together to a set value. This value depends on the adjusting screw and the actuator and defines the gap between the brake shoe and brake drum.S469_130 S469_02426 Functions of the electromechanical parking brakeThe electromechanical parking brake has the following functions: Parking brake Dynamic auto release Dynamic emergency brake Further information can be found in self-study programme no. 346 “Electromechanical parking brake”.ABS/ESP anti-lock brake system Continental/Teves MK 25 A-XTThe Touareg 2011 features a new ESP unit. The MK 25 A-XT ESP system has been developed for vehicles with high axle loads. The essential new features include: Analogue separation and inlet valves Sensor cluster with combined rotary rate, lateral and longitudinal acceleration sensor Integrated brake pressure sensorS469_003The MK 25 A-XT system has the following functions: ABS ABS Plus HBA (hydraulic brake assist) FRAD (maximum rear axle braking) Automatic hazard warning lights Overboost ESP Brake disc dry braking Vehicle/trailer stabilisation HBV (hydraulic brake with vacuum servo) only V8 FSI Roll-over prevention (ROP) Prefill function (brake pads rest against brake discs) TCS EBC (engine braking effect control) EDL (electronic differential lock) Dynamic emergency braking function, ECD (Electronic Controlled Deceleration) AUTO HOLD Hill descent assist systemYou will find further information on the respective functions in self-study programme no. 374 “Traction Control and Assist Systems”.27 Brake systemON ROAD and OFF ROAD driving programmeThe Touareg 2011 has an ON ROAD and OFF ROAD driving programme. The programmes adapt the following functions: ON ROAD: ● Driving on surfaced roads OFF ROAD: ABS Plus: Raised threshold for better chock formation on loose surfaces (e.g. sand) ● EDS/ASR: Later intervention in torque regulation, EDL control even at low levels of slippage ● Hill descent assist system ● Adapted shift program with shallow accelerator characteristic curve and no automatic upshifting in the Tiptronic gate●When the vehicle is set to the OFF ROAD driving programme, the lamp in the switch lights up.Lamp in switchThe function lamp for the hill descent assist system lights up to indicate that the system is ready. The function lamp flashes when the system is active.S469_006S469_062 Function lamp for hill descent assist system S469_06428 Stationary vehicle managementThe stationary vehicle management has the task of ensuring that the Touareg 2011 has a secure footing in a variety of situations. The following systems in the vehicle have an influence on the stationary vehicle management:● ● ● ●Aisin 1000 torque converter EPB, electromechanical parking brake ESP, hydraulic brakes Engine control unit with start/stop systemThe stationary vehicle management is implemented by:●AUTO HOLD Holds the vehicle stationary after you brake to a standstill and release the brake pedal. HILL HOLD Prevents the vehicle rolling back after rolling to a stop or braking with the brake pedal on an incline and also makes pulling away simple. Electromechanical parking brake, EPB Safely holds the vehicle stationary, regardless of whether on level ground, on uphill slopes or downhill slopes.●●You will find further information on the Aisin 1000 torque converter in self-study programme no. 466 “The 8-speed Automatic Gearbox 0C8”.You will find further information on the start/stop system in self-study programme no. 426 “Start/Stop System 2009” and in self-study programme no. 449 “The Touareg 2011”.29 Brake systemAUTO HOLD functionThe AUTO HOLD function holds the fully laden vehicle on a maximum uphill slope or maximum downhill slope of 30%. The basic function is holding the vehicle hydraulically while it is stationary. If the vehicle is stationary for longer periods, the activated ESP solenoid valves heat up. After 3 minutes at the latest, the hydraulic brake application is “handed over” to the electromechanical parking brake (EPB). This prevents the coils of the ESP solenoid valves being damaged. The hold function is only ended when the driver wants to pull away or ends the AUTO HOLD function by pressing the button.Activation conditions:EPB, ESP fault-free Driver’s door closed Driver’s belt lock engaged AUTO HOLD button pressed Engine is not running in non-hybrid vehicles Ready to drive with hybrid vehicles (Ready indicator in display)The readiness of the function is indicated by the warning lamp for AUTO HOLD, which is in the AUTO HOLD button.Function procedure:●S469_149 S469_150●●●Driver brakes hydraulically, electromechanical parking brake warning lamp K213 = green Vehicle is held hydraulically. In order to protect the valve coils in the ESP control unit against overheating, the handover to the EPB will occur after 3 minutes at the latest (K213 = red). If the vehicle rolls back, brake pressure is built up one single time via ESP. If the vehicle rolls again, handover to EPB (K213 = red).S469_152Upon handover to the EPB, the electromechanical parking brake warning lamp K213 in the dash panel insert changes from green to red.30 HILL HOLD functionThe HILL HOLD function prevents the vehicle rolling back on gradients when gears D or S are selected or when the selector is in the shifting/Tip gate. This occurs both when braking to a standstill and also when rolling to a stop on uphill slopes. This function is always active. There is no indicator for the HILL HOLD function in the dash panel insert. The hold function is carried out by the gearbox. If the gearbox oil temperature is too low (10°C), the HILL HOLD function is taken over by the ESP function or by the EPB after 3 minutes. The HILL HOLD function is only ended when the driver wants to pull away.Activation conditions:Gears D, S or Tip gate Engine running Ready to drive in hybrid vehicles (Ready indicator in display)S469_149Function procedure:Gearbox oil temperature greater than +10°C: The vehicle is held by the gearbox, i.e. by the locking freewheel of the 8-speed automatic gearbox. You will find more information in SSP 466 “The 8-speed Automatic Gearbox 0C8”. Gearbox oil temperature less than +10°C: ● If the driver brakes the vehicle or the vehicle rolls to a stop, it will be held hydraulically. In order to protect the valve coils in the ESP control unit against overheating, the handover to the EPB will take place after 3 minutes at the latest (K213 = red). ● If the vehicle rolls back, brake pressure is built up one single time via ESP. ● If the vehicle rolls again, handover to EPB (K213 = red).31 Brake systemRestart assist systemThe restart assist system is directly linked to the start/stop function. It prevents the vehicle from jolting when the engine is restarted. If the driver starts the engine by releasing the brake pedal, the engine torque is passed onto the wheels via the drive train when the engine is restarted. In this case, the vehicle is braked hydraulically until the engine reaches its idling speed. The restart assist system operates independently of the gradient and gear and is only available when the AUTO HOLD function is not active. The restart assist system does not have a switch nor a warning lamp and there is no feedback for the driver about this function being activated.Activation conditions:Engine restart after start/stopFunction procedure:●● ●When you release the brake pedal, the driver braking pressure is stored. Stop phase until the engine is started. The hydraulic brake is released.S469_14732 Summary of stationary vehicle managementHILL HOLD Vehicle rolls to a stop Gearbox oil temperature less than 10°C ESP (pump builds up pressure)AUTO HOLD button pressed-After 3min. handover to EPBDriver brakes to a standstill Gearbox oil temperature less than 10°C -ESP (driver braking pressure is stored) After 3min. handover to EPB-ESP (driver braking pressure is stored) After 3min. handover to EPB-Vehicle rolls to a stop Gearbox oil temperature greater than 10°C-Vehicle is held by gearbox.Driver brakes to a standstill Gearbox oil temperature greater than 10°CVehicle is held by gearbox.-ESP (driver braking pressure is stored) After 3min. handover to EPB-Start/stop function/ engine off-Restart assist system-ESP (driver braking pressure is stored) After 3min. handover to EPB-33 SteeringSteeringAs standard, the Touareg 2011 uses a speed-dependent, hydraulic rack-and-pinion steering system with a more direct steering gear ratio. That means that, when the steering wheel is turned 90°, the front wheels are turned further compared with the previous model. Oil is supplied by a regulated power steering pump driven by the combustion engine. Its controlled delivery volume makes a substantial contribution to reducing CO2 emissions.Steering wheelsTwo 3-spoke steering wheels made from wood and leather with multifunction buttons are available as standard for the Touareg 2011. If the vehicle is equipped with the lane departure warning system (Lane Assist), a vibration motor will be fitted in the lower spoke of the steering wheel.S469_036S469_03834 Steering columnA mechanically adjusted steering column and an electrically adjusted steering column are available for the Touareg 2011. Both steering columns use a new steering column concept with a new set-up and new connecting points. The steering columns, which were developed by Thyssen Krupp Presta, are approx. 1kg lighter than the ones used in the previous model. Both variants are equipped with an electrical steering column lock. The electrical steering column lock can be replaced separately. Adjustment range: - Longitudinal adjustment at bottom approx. 160mm - Longitudinal adjustment at top 60mm + 70mm crash travel - Height adjustment 50mmMechanically adjusted steering columnS469_084 Plastic adjusting leverPlastic adjusting lever at side with predetermined breaking point Wedge disk/cam clamping system Form fit in height and longitudinal adjustment due to stricter crash requirements Height adjustment with toothed strip on both sides Longitudinal adjustment with toothed plateElectrically adjusted steering column (EASC) with memory functionControl unit for electrical adjustment-Control unit for electrical adjustment on the steering columnS469_00235 SteeringHydraulic power steering pumpThe power steering pump in the Touareg 2011 is a regulated power steering pump manufactured by ZF with a delivery volume of up to 13cm3/min.DesignOutput to steering box Input from power steering fluid reservoir Control plungerCam ring Control of stroke displacement on both sidesRotorVanesOuter ringS469_10236 Performance comparison: non-regulated and regulated pump The fuel saving is approx. 0.15 litres/100km. At engine speeds above 3500-4000rpm, the fuel savings are approx. 0.8 litre/100km compared with a nonregulated pump.Output [ W ]Non-regulated pumpLossesRegulated pumpEffective output of pumpS469_044Engine speed [rpm]FunctionAt idling speed: The pump cam ring is pressed against the outer ring by the spring force and the internal pressure conditions. The largest possible delivery volumes result on the suction and pressure sides. The delivery volume rises proportionally as the engine speed increases.Power steering fluid reservoir Pressure limiting valve Control plungerTo the steering box ThrottleCam ringRotorPressure spring Outer ring Legend = suction side = pressure side = low pressure = neutral pressure Pressure line Control line S469_04237 SteeringAs the engine speed rises: The pressure in the pump also rises. The pump pressure is applied on one side of the control plunger and the control plunger is moved to the left against the spring force as the pressure rises. Within a defined medium engine speed range, the channels to the chambers between the outer ring and the cam ring are closed by the control plunger. This results in pressure equilibrium between the left-hand and righthand chamber. The cam ring is held in a defined central position and the delivery volume remains almost constant.Control plungerCam ring Outer ring S469_048 Left-hand chamber Right-hand chamberIf engine speed continues to rise: The delivery volume and pressure increase. The control plunger is moved further to the left against the spring force. This connects the channel to the lefthand chamber with the suction line. Pump pressure reaches the opposite right-hand chamber. The cam ring is pushed against the spring force to the left. This reduces the eccentricity between the rotor and cam ring. The delivery volume is reduced and an excessive pressure increase is thus prevented. The resulting reduction in pump power requirement causes the energy consumption to be reduced considerably.Suction lineControl plungerRotor Cam ring Outer ringS469_052Left-hand chamberRight-hand chamberLegend = suction side = pressure side = low pressure = neutral pressure38 Hybrid electrical componentsElectrical running gear components in hybrid versionSince the combustion engine is decoupled and switched off while the vehicle is driven by the electric motor, the running gear components need to be driven electrically. All functions that are covered by the combustion engine in conventionally motorised vehicles are performed by electric motors and pumps in the Touareg Hybrid. This is necessary to also supply, for example, the braking system and power steering with sufficient pressure in electrical mode.Electrical power steering pump V466The power steering pump for the electrohydraulic power steering is located on a console on the front left wheel housing underneath the headlight. Task It provides the demand-regulated working pressure for the power steering hydraulic system. Regulation is carried out relative to the vehicle speed, the steering angle and the speed at which the steering wheel is turned. Effects upon failureS469_100If the power steering pump fails, there is no steering assistance. The steering can, however, still be operated with greater effort.39 Hybrid electrical componentsBrake servo vacuum pump V469Bolted onto the engine from underneath at the front right. Task The brake servo vacuum pump is solely responsible for creating the vacuum in electric mode. It therefore also provides the necessary pressure for the brake servo assistance. It can run in a supportive role during start-up and in combustion engine mode. The vacuum pump continues to provide the vacuum to control the shutter in the on-demand coolant pump for the combustion engine. An internal pressure accumulator ensures a pulse-free, constant vacuum. Effects upon failure If the vacuum pump is faulty, the combustion engine will start. It is no longer possible to drive in electric mode.S469_15440 Wheels and tyresOverviewOnly alloy wheels from 17" to 20" are available for the Touareg 2011. The 17" and 18" tyres have a diameter of 750mm. The 19" and 20" tyres have a larger diameter of up to 766mm.S469_070S469_072S469_074S469_076Sonora 7.5Jx17 ET50 235/65R17 108V 255/60 R17 106V 235/65R17 108VAtacama 7.5Jx17 ET50 235/65 R17 108V 255/60 R17 106V 235/65 R17 108VTacora 8Jx18 ET53 255/55 R18 109W 255/55 R18 109VKarakum 8Jx18 ET53 255/55 R18 109W 255/55 R18 109VS469_078S469_080S469_082Everast 8.5Jx19 ET59 265/50 R19 110V 265/50 R19 110W 265/50 R19 110V Without chainPikes Peak 9Jx20 ET57 275/45 R20 110WMetropolitan 9Jx20 ET57 275/45 R20 110W Winter tyresWithout chainWithout chainThe Touareg comes with a breakdown set (Tyre Mobility Set) as standard. There is no spare wheel with full-size tyre. A 19" alloy temporary spare wheel is available as an option. The Touareg Hybrid is optionally available with an 18" Yukon 8Jx18 ET53, 255/55 R18 wheel.41 Tyre pressure monitorOverviewThe tire pressure monitoring system allows position-related (to all four wheels) tyre pressure monitoring with the aid of the following components:●● ●A tyre pressure monitor control unit with integrated aerial Location: Driver-side longitudinal member, near to B-pillar, Four trigger senders in the wheel housings Four wheel electronics in the vehicle tyresWheel electronicsTrigger senderTyre pressure monitor control unitS469_140Via the trigger senders, the control unit can address each of the four wheel electronics with an LF radio signal (Low Frequency) and request sending of a data telegram. This data telegram is received by the control unit and immediately evaluated for the corresponding wheel position.SettingsThe vehicle-specific target pressure is stored in the control unit at the factory. If the vehicle has several different target pressures, they can be changed in the settings menu by selecting the tyre dimension. An additional target pressure can be added for custom tyres. In the settings menu, you can also select the vehicle load if it is relevant to the tyre pressure.S469_15842 FunctionTarget pressure Actual pressureIf there are significant differences between the actual pressure and the target pressure, the tyre pressure monitor warning lamp in the dash panel insert will light up. The warning status is also indicated by text messages and the actual pressure of the individual tyres is displayed in the dash panel insert.Tyre pressure monitor warning lampS469_142Warning messagesText message “Check tyre pressures” Tyre pressure Actual pressure target pressure (pressure difference - 0.3bar) Actual pressure target pressure (pressure difference - 0.5bar) Actual pressure 1.4bar or pressure loss 0.2bar/min Warning status Note No tyre pressure monitor warning lamp Hard warning I Tyre pressure monitor warning lamp lights up Hard warning II Tyre pressure monitor warning lamp lights up + gong“Tyre pressures too low”“Flat tyre!”If there is a system fault, the tyre pressure monitor warning lamp flashes for approx. 65 seconds. Then it lights up constantly. If the wheel electronics are not receiving, the tyre pressure monitor warning lamp lights up constantly.CodingThere are two coding variants:●●In the first coding variant, the tyre pressure monitor is switched off automatically when you start a journey if the wheels were fitted without wheel electronics. If the system has been switched off, it will be automatically activated as soon as it detects at least one wheel electronics unit on the vehicle (e.g. after a wheel is changed). In the second variant (USA only), switching off is prohibited by law.43 Transfer boxTransfer box 0BVAs an optional extra (4XMOTION), the Touareg 2011 is available with the familiar centre differential with reduction stage, transfer box and longitudinal lock and the rear axle differential with axle differential lock. The basic torque distribution has changed compared with the Touareg 2003. In the Touareg 2003, the basic distribution in the differential was 50:50 between the front and rear axles. In the Touareg 2011, the torque is distributed at a ratio of 38:62 between the front and rear axles. This has been achieved by giving the sun wheel in the planetary gear set a smaller pitch circle diameter.Cross-section of differential in Touareg 2003Cross-section of differential in Touareg 2011Internal gearPlanet gearsS469_132Sun wheel (52 teeth)Sun wheel (40 teeth) Basic distribution in differential 38:62S469_134Basic distribution in differential 50:50You will find more information on this centre differential in self-study programme no. 302 “Touareg - Chassis and four-wheel drive concept”.44 Transfer box 0BUThe transfer box 0BU is available in the basic equipment version (4MOTION). It is a self-locking centre differential and has the task of compensating the different speeds at the front and rear axles as well as distributing the drive power between the axles depending on the traction. The transfer box operates purely mechanically and reacts without delay to changes in driving situations. Its compact design, low weight and lifetime oil filling mean that the transfer box is maintenance-free and reliable.S469_067S469_069Technical dataManufacturer Gearbox code Torque ATF oil part number Magna Powertrain 0BU up to 800Nm see electronic parts catalogue Lifetime oil filling approx. 25-31kgThe weight of the transfer box depends on the engine/gearbox combination. The following components of the transfer box are adapted: the drive chain the drive chain sprockets the neck length of the transfer boxWeight45 Transfer boxDesignleng NeckthRear axle outputChain driveInput shaft/hollow shaft Self-locking centre differentialFront axle output S469_073The transfer box is bolted directly onto the automatic gearbox. There are different neck lengths to go with the different engine and gearbox lengths. The input shaft, which is a hollow shaft, transmits the gearbox output torque to the transfer box. The differential compensates the different speeds of the axles and distributes the drive torque. Power is sent to the rear axle via an output shaft arranged coaxially to the input shaft. The upper chain sprocket is mounted on the output shaft and transfers the front axle torque to the lower chain sprocket via a chain.46 Planetary gear setDesignPlanet carrier Housing Sun wheelInternal gearInput shaft/hollow shaft Planet gearsFriction platesS469_055The basic set-up of the self-locking centre differential is a simple planetary gear set with planet carrier, planet gears, internal gear and sun wheel. In addition, friction plates are fitted in the centre differential. The friction plates are made from nickel-plated steel. These friction plates and the ATF oil influence the frictional torque and thus the locking value of the differential to a great degree. The frictional torque arises due to the self-locking effect of the helical toothing and the force of the sun wheel and internal gear acting on the friction plates.Friction plate Friction plate Friction plateFriction plate Sun wheelPlanet carrier S469_057Planet gears Internal gear Drive hub/ rear axle Housing47 Transfer boxAsymmetric basic distributionPlanet carrierPlanet gear21Sun wheel (drive for front axle) S469_030Internal gear (drive for rear axle)The gearbox output moment is distributed in an asymmetric (unequal) basic torque distribution of 40:60 (front axle to rear axle). This is made possible by the different pitch circle diameters of the sun wheel (output to front axle) and internal gear (output to rear axle). 1 = smaller pitch circle diameter: short lever arm/lower torque to front-axle drive 2 =larger pitch circle diameter: longer lever arm/greater torque to rear-axle drive48 Asymmetric/dynamic torque distributionInside the locking range of the differential, the gearbox output torque can be distributed between the front and rear axle. The locking range of the front axle is between 20% to 60% of the gearbox output torque. The locking range of the rear axle is between 40% to 80% of the gearbox output torque.The EDL intervenes outside the locking range of the differential.Drive torque at front axle [%] 100 Yellow - orange: Low friction values = snow and iceDrive torque at rear axle [%] 080EDL2060 Green: High friction valves = dry and wet4040 Basic distribution 20Differential locking range6080 EDL0100S469_053In addition to the asymmetric basic distribution of 40:60, a frictional torque is created in the differential that is proportional to the drive torque and results in a corresponding locking torque. The locking torque plus basic distribution are decisive for the maximum torque distribution to the axles.Basically, the centre differential reacts to torque changes at the axles. If an axle loses traction, the drive torque within the locking range will immediately be sent to the other axle. Traction is the conversion of the available drive torque into propulsion. If the locking range of the centre differential is exceeded, the EDL control system intervenes and ensures propulsion.49 Transfer boxExample torque distributionThe following example shows how the Touareg reacts to changing road conditions with the self-locking centre differential.S469_0861000800Torque [Nm]6004002000t1t2t3t4Time EDL braking torquePropulsion Constant 1000Nm drive torqueFront-axle torque Rear-axle torqueIn this example, the Touareg drives over a small patch of ice (driving mode t2 and t3) with constant drive power. The slipping limit* is assumed to be 250Nm on each axle. The total drive torque is (t1 and t4) 1000Nm. Upon reaching the patch of ice (t2), the front axle loses traction and the drive torque falls to the slipping limit* of 250Nm. Due to the locking effect of the differential, the drive torque at the rear axle rises to 750Nm at the same time. Since the distribution of the torque is within the locking range of the differential, there is no speed difference between the axles. 100% of the drive power is converted into propulsion, no intervention is required from the EDL control system. At the point in time t3, the front axle has already left the patch of ice. Now the rear axle is subject to the reduced frictional value and can only transfer a torque of 250Nm. To ensure optimum traction to the front axle, the EDL control system now intervenes to provide support. 85% of the drive power is converted into propulsion.* maximum transferrable torque of an axle on the ice surface50 Basic distribution and torque developmentDriving situation All wheels are driving on the same surface and have the same grip.S469_056 Planet carrier Planet gear Differential case Drive torque to front axle 40%Gearbox output torqueDrive torque to rear axle 60%S469_054 Drive hub/ rear axle Sun wheelFriction plate Internal gear Friction plateDistribution The gearbox output torque is distributed between the front and rear axle at a ratio of 40:60 when the grip of all wheels is the same.Torque development in differential The gearbox output torque is sent to the differential case via the hollow shaft. The planet carrier, which is bolted to the case, transfers the gearbox output torque via the planet gears to the sun wheel (green) and the internal gear (blue).51 Transfer boxAxial forceThe axial force is a force that acts in the direction of an axis of a body. The differential gears have defined helical toothing. The drive torque thus applies an axial force to the gears, which act on various friction plates and produce a frictional torque. The frictional torque then leads to the desired locking effect (locking torque). The size of the locking torque is defined by the locking value. The locking value indicates the factor by which the drive torque is sent to the axle that has greater traction.Locking effect during acceleration= axial force during accelerationS469_058Angled splines to increase the frictional force with additional friction platesLocking effect on the overrun= axial force on the overrunS469_06052 LubricationGuide tab Oil collector with oil guideOil pathOil sumpS469_063The design of the transfer box 0BU allows ATF oil to be used for lubrication. The upper shafts and the differential are lubricated using an oil collector and special oil guide. While the vehicle is driven, the chain transports the oil from the oil sump towards the differential, where it is scraped off by the oil collector. The oil guide leads the oil into the differential and onto the input shaft bearing. Sufficient oil is delivered as soon as the vehicle reaches walking speed. The system also works when the vehicle is reversing. An oil circuit is formed by the centrifugal force in the differential. When the vehicle is stationary, this oil circuit breaks up and coats the internal lubricating points. The differential case has been designed so that a certain volume of oil remains when the vehicle is stationary. Lubrication is ensured as soon as the vehicle pulls away.53 Transfer boxOperating instructionsTowing:If the vehicle has to be towed with raised front or rear axle and the wheels of the raised axle cannot turn, a maximum speed of 50km/h and a towing distance of 50km must not be exceeded. Also no gear may be selected.Brake test stand:A brake test can be performed on a slowly running test stand (up to 6km/h). The wheels must be driven by the test stand. No gear may be selected and the differential lock (if equipped) may not be engaged.Output test stand:Only a 4-wheel roller dynamometer may be used for the output test.A constant high speed difference between the front and rear axle combined with a high load will damage the centre differential. The self-locking centre differential cannot be compared with a mechanical 100% differential lock. If an axle or a wheel spins without power, there is no drive. Outside the locking range of the transfer box 0BU, the EDL control system provides support. If a wheel loses static friction, the power is distributed evenly to all wheels by braking that particular wheel. If the propshaft is removed, there is no drive.54 Splines on propshaftsThe propshafts on the Touareg have been changed. They have been designed with splines to save weight. The splines are locked onto the output shaft of the transfer box with a secured circlip (0BV/0BU).S469_075Propshaft splines Output shaft splinesS469_138O-ring (seal) CirclipThe circlip and seal need to be replaced before the propshaft is installed.55 Test yourselfWhich answers are correct? One or several of the answers could be correct.1.What is meant by the “Prefill” function? a) Increasing the tyre inflation pressure to the “full load” range with subsequent initialisation of the tyre pressure monitor. b) The ESP system pre-fills the brake system with pressure so that the brake pads are already in contact with the brake discs in case of an emergency stop. c) Pre-filling the brake system with brake fluid when the brake fluid is changed. d) Factory filling of the air suspension with nitrogen.2.What advantage does the regulated power steering pump have compared with non-regulated power steering pumps? a) The steering assistance is considerably higher with the regulated power steering pump. b) Reducing the power requirement of the pump significantly reduces the energy consumption and thus the fuel consumption. c) Reducing the power requirement of the pump increases the energy consumption and the fuel consumption rises by 0.8 litres/100km.3.How many level and acceleration sensors are used by the air suspension system on the Volkswagen Touareg 2011? a) 12 sensors, i.e. 4 senders each for body acceleration, vehicle level and wheel acceleration. b) 7 sensors, i.e. 3 senders for body acceleration and 4 senders for vehicle level c) 10 sensors, i.e. 4 vehicle level senders, 3 wheel acceleration senders and 3 body acceleration senders56 4.What is the basic distribution between the front axle and rear axle in the transfer box 0BU? a) 50% : 50% (front axle to rear axle) b) 30% : 70% (front axle to rear axle) c) 60% : 40% (front axle to rear axle) d) 40% : 60% (front axle to rear axle)5.How often does the ATF oil in the transfer box 0BU have to be changed? a) Every 60,000km b) Every 120,000km c) It does not need to be changed.Answers 1. b); 2. b); 3. b); 4. d); 5. c)57 Notes58 59 469© VOLKSWAGEN AG, Wolfsburg All rights and rights to make technical alterations reserved. 000.2812.41.20 Technical status 06.2010 Volkswagen AG After Sales Qualifizierung Service Training VSQ-1 Brieffach 1995 D-38436 Wolfsburg❀ This paper was manufactured from pulp bleached without the use of chlorine.