TECHNICAL DOCUMENTATION
SSP 470 The Touareg 2011 Electrics

This PDF is currently unavailable.
Read document text
Service TrainingSelf-study Programme 470The Touareg 2011 Electrics/electronics Design and FunctionThe Touareg 2011 sets new standards in the area of electrics/electronics. Of all the latest Volkswagen vehicles, it features the most modern and innovative network that enables communication among all electronic control units. For the first time at Volkswagen, two new data transfer systems have been introduced with the new Touareg in addition to the familiar CAN data bus and LIN data bus. The new FlexRay data bus joins the control units of the improved driver assist system for adaptive cruise control ACC. With the MOST bus, the infotainment system uses the most modern fibre-optic technology and thereby boasts new highlights in terms of function, display and controls.As a luxury class vehicle, the Touareg 2011 not only has a modern infotainment system and improved driver assist systems but also completely newly developed functions, such as Area View and dynamic light assist. This self-study programme is intended to help you become familiar with the electrics/electronics and also the driver assist systems employed in the Touareg 2011 and to understand how they interact.S470_001The self-study programme portrays the design and function of new developments. The contents will not be updated.For current testing, adjustment and repair instructions, refer to the relevant service literature.Attention Note2ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Electrical system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Convenience electronics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Driver assist systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Infotainment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Test yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 533IntroductionOverviewTo start with, the diverse new features of the electrics and electronics of the Touareg 2011 are given some clarity. Listed as follows, therefore, are the main participating new components and functions, which are allocated to the two large main groups infotainment and driver assist systems. However, note that as networking of the most diverse vehicle systems intensifies because components are being combined to realise several vehicle functions, so clear assignment to one system constitutes a simplification, this in reality may not be a representation of the actual conditions in certain circumstances.InfotainmentThe following components and component groups have either been further developed or added as new items:● ● ●● ● ● ●MOST data bus Dash panel insert with 7" TFT colour display (premium) Control unit for information electronics 1 with - internal hard-drive - Telephone module with Bluetooth, GSM part (optional) - Navigation module - Media player DYNAUDIO sound system Decentralised radio tuner TV tuner (optional) Additional DVD changer (optional)The following infotainment systems and functions are available, for example, as further developments in the Touareg 2011 or are new additions: Animated 3D navigation guidance in dash panel insert (premium) Display and operation of the surrounding area features using the Rear View and Area View (optional) functions on the touch screen of the infotainment in the centre console Premium telephone connection (equates to permanently installed telephone with dedicated SIM card slot) Standard Bluetooth module (integrated) has to be enabled via PR number Radio/navigation system RNS 850Further information on the subject of infotainment can be found in self-study programme 473 "Infotainment in the Touareg 2011".4Vehicle and driver assist systemsThe following components and component groups have either been further developed or are new additions: Bi-xenon headlight modules with main beam mask and LED day driving lights FlexRay data bus Rotating, electronic ignition lock Exclusive high speed CAN data buses Multifunctional camera Dive rate senderThe following vehicle systems and driver assist systems are available, for example, as further developments in the Touareg 2011 or are new additions: Adaptive cruise control ACC Dynamic cornering light Dynamic light assist Reversing assistant Lane departure warning Area View, optional 5th generation immobilizerS470_0695Electrical systemThe networking conceptFor the launch of the Touareg, the highest level of infotainment equipment is installed. This means that in all instances RNS 850 and MOST fibre-optics are used. The data bus diagnostic interface J533 forms the interface for communication for the following data bus systems: m Powertrain CAN data bus Chassis CAN data bus Display and operation CAN data bus Convenience CAN data bus Extended CAN data bus J623 T16 J624J492J197f J533 hnAll of the CAN data buses are high speed buses with a data transfer rate of 500kBit/s. J285 The FlexRay data bus, installed depending on the optional ACC, meets the higher demands of future networks, particularly with regards to a higher data transfer rate compared with the familiar CAN data bus. This is a standard that all manufacturers apply in which the data transfer rate is 10MBit/s. J446 J791oJ519J502J136J364J255J885*J412*E265R*Key Powertrain CAN data bus Chassis CAN data bus Convenience CAN data bus Display and operation CAN data bus Infotainment CAN data bus Extended CAN data bus LIN data bus FlexRay data bus MOST data bus6J217J234J706Key E221 E265 G85 G397 G419 J104 J136 J197 J217 J234 J255 J285 J345 J364 J386 J387 J388 J389 J393 J412 J446 J492 J501 J502 J519 J521 J525 J527 J533 J540 J605 J623 J624 J647 J706 J772 J791 J885 J928 R R215 T16 f h m n o p * **G419 J647 J540 J104 G85pE221J393J527J521J345J605J501R215*J525*J772**/ J928**Operating unit in steering wheel Operating and display unit for Climatronic in rear Steering angle sender Rain and light sensor ESP sensor unit ABS control unit Control unit for seat and steering column adjustment with memory function Adaptive suspension control unit Automatic gearbox control unit Airbag control unit Climatronic control unit Control unit in dash panel insert Trailer detector control unit Auxiliary heater control unit Driver door control unit Front passenger door control unit Rear left door control unit Rear right door control unit Convenience system central control unit Mobile telephone operating electronics control unit Parking aid control unit Four-wheel drive control unit Multifunction unit control unit Tyre pressure monitor control unit Onboard supply control unit Front passenger seat adjustment with memory control unit Digital sound package control unit Steering column electronics control unit Data bus diagnostic interface Control unit for electromechanical parking brake Rear lid control unit Engine control unit Engine control unit 2 Lateral locks control unit Seat occupied recognition control unit Reversing camera system control unit Control unit for parallel parking assist Interface for infotainment CAN bus Area view camera control unit Radio RCD 550 (introduced later) Interface for external multimedia devices 16-pin connector FlexRay data bus Extended CAN data bus MOST data bus LIN data bus on J533 LIN data bus on J519 LIN data bus on J393 Only on vehicles without MOST (introduced later) Depending on equipmentCVBSJ388J386J389J387S470_026CAN data bus line LIN data bus line Private bus FlexRay data bus line MOST fibre-optic cable7Electrical systemLIN data bus rangesShown as an example here are the LIN data bus network ranges from three control units: LIN data bus on data bus diagnostic interface J533 LIN data bus on onboard supply control unit 1 J519 LIN data bus on convenience system central control unit J393In this way, the overview diagram for the overall network on the previous double page spread is given slightly more clarity and shows you how complicated and multi-layered the network architecture has become even beyond the large CAN data bus network ranges.LIN data bus on Onboard supply control unit 1 J519 J519Onboard supply control unit 1 has three LIN data bus lines that are separate from each other. In total 9 LIN data bus participants are connected to this control unit. Key E1 G238 G397 G65 J400 J519 J530 J799 J800 J866 Light switch Air quality sensor Rain and light sensor High pressure sender Wiper motor control unit Onboard supply control unit Garage door opener control unit Front right seat ventilation control unit Front left seat ventilation control unit Control unit for electrically adjustable steering columnLIN 1E1G397J400J800J799LIN 2G238J530G65LIN 3 S470_128J8668LIN data bus on convenience system central control unit J393 J393The central control unit for convenience system also makes use of the three separate LIN data bus lines. In total, 6 LIN data bus participants are connected to this control unit. Key D E284 G273 G384 H8 J245 J393 J764 Ignition/starter switch Operating unit for garage door opener Interior monitoring sensor Vehicle inclination sender Anti-theft alarm system horn Sliding sunroof control unit Convenience system central control unit Electronic steering lock control unitG273/G384LIN 1J245E284LIN 2H8DLIN 3J764S470_130LIN data bus on data bus diagnostic interface J533 J533In addition to the connections on CAN and MOST, the diagnostic interface (Gateway) also features an individual LIN data bus with three data bus participants.CLIN 1Key C J367 J532 J533S470_126J367 J532Alternator Battery monitoring control unit Voltage stabiliser Data bus diagnostic interface9Electrical systemCAN-Extended, FlexRay, MOSTCVBS L k R161 b J533 d J285* fw bKeyLVDS J794 R78R J525aJ769 J844 J428 J855 J854 G752 J745 LVDS J852J770J850J851J667 J668G752 Dive rate sender J285 Control unit in dash panel insert (* Premium dash panel insert) J428 Control unit for adaptive cruise control J525 Digital sound package control unit J533 Data bus diagnostic interface J667 Power output module for left headlight J668 Power output module for right headlight J745 Cornering light and headlight range control unit J769 Lane change assist control unit J770 Lane change assist control unit 2 J794 Control unit 1 for information electronics J844 Main beam assist control unit (introduced later) J850 Control unit 2 for adaptive cruise control J851 Image processing control unit J852 Camera control unit J854 Front left belt tensioner control unit J855 Front right belt tensioner control unit R Radio R78 TV tuner R161 DVD changer a b d fw k L Powertrain CAN data bus Display and operation CAN data bus Diagnostic CAN Chassis CAN data bus Convenience CAN data bus LIN data busS470_042Key Powertrain CAN data bus Chassis CAN data bus Convenience CAN data bus Display and operation CAN data bus Extended CAN data bus LIN data bus FlexRay data bus MOST data bus CAN LIN data bus line data bus lineFlexRay data bus line MOST fibre-optic cable10The new bus systemsMOST busWith the Touareg 2011 a new fibre-optic connection finds its debut at Volkswagen. The connection is employed by infotainment components to communicate with each other using the MOST protocol. MOST stands for "Media Oriented Systems Transport". It is a serial bus system for transferring audio, video, voice and data signals via a fibre-optic cable. Seen in physical terms, MOST is a ring-shaped network structure (network topology). A MOST network can comprise up to 64 MOST devices. The order in which the infotainment components must be placed in the ring is determined during development and may not be altered.MOST bus in Touareg 2011 Control unit for information electronics 1 TV tunerDVD changerDiagnostic interface for data bus Control unit in dash panel insert S470_054RadioControl unit for digital sound packageThe MOST bus in the Touareg 2011 has the following features:● ● ● ●● ●Optical data bus system Data transfer rate: 21.2 Mbit/s Ring topology Address-orientated messages to a specific recipient Cyclic and event-controlled data transfer High level of safety against disturbanceWith the aid of the optic MOST bus, data is exchanged among the participating components in digital form. Data transfer with the aid of fibre-optics enables a considerably greater data transfer rate. Compared with radio waves, light waves have short wavelengths. They do not generate electromagnetic interfering waves themselves and, at the same time, are not sensitive to interference from external electromagnetic sources.11Electrical systemData protocol1 frame = 512bit (64bytes) 480bit (60bytes)S470_096 Data field for synchronous data (synchronous channel) Boundary field = 4bit (boundary description) Start field = 4bit (preamble) Data field for asynchronous data (asynchronous channel) Control channel = 16bit Status field = 7bit Parity field = 1bit (parity)The data to be transferred are sub-divided into frames. Each frame comprises 512bits (64bytes) of digital information. The overall length of a frame is made up of one start and one boundary field, two data fields, one controlling data field, one status and one parity field. The maximum amount of data that can be stored in both data fields is limited to 480bits (60bytes) due to this fixed division. The data is transferred via 3 channels: - Control channel for controlling data - Synchronous channel for audio and video data transfer (synchronous realtime transfer without intermediate storage) - Asynchronous channel for large quantities of data, e.g. map data to dashboard insert (asynchronous, eventcontrolled data transfer, intermediate storage possible) On the new Toureg 2011, the size of the synchronous data field is fixed at 40 bytes and the asynchronous data field is fixed at 20 bytes.12Structure of fibre-optic cableOuter sheath e.g. orangeInner sheath always blackFront surfaceCoreCladding S470_098The fibre-optic cable comprises several layers:●● ●●the outer coloured coat serves as a means of identification, as protection against mechanical damage and against temperature extremes. The black inner coat protects the core against light irradiation. The cladding (polymer fluoride) is a layer around the core with lower refractive index. Its thickness is several microns and it ensures that the light fed through the core nearer to the edges is reflected back to the centre of the core, thus preventing "lateral" loss of light from the core. The core is the central area of the fibre-optic cable. It is made from specially conditioned plexiglass. It channels the light with practically no loss.To prevent any loss in the transfer of data, the front surface of the fibre-optic cable has to be smooth, vertical and clean. Dirt and scratches on the front surface could lead to interference and data transfer losses and it could also impair the performance of the fibre-optic cable.13Electrical systemFlexRayThe higher demands on data rates and also data security necessitate the introduction of time-controlled bus systems with high band width (as a comparison: the CAN data bus is an event-controlled bus system). FlexRay is a new data bus system, which is debuted in the Touareg 2011. FlexRay is a serial, deterministic and faulttolerant field bus system for use in automobiles. At 10Mbit/s, FlexRay is twenty times faster than a high speed CAN (which has 500kbit/s). A further important feature is the guaranteed reaction and latent period. A latent period here describes the time a message needs to travel from the sender to receiver. In this context, deterministic transfer (predetermined, restricted) is another way of describing it. This means that the information reaches the recipient or recipients at a fixed or predetermined point in time (realtime capability). Unlike the CAN data bus, at least two control units are needed on the FlexRay data bus in order to start the FlexRay. These control units are called cold start control units (KS). Their number is restricted to max. three per FlexRay network. For time-controlled communication within this set network, the shared time basis is formed by the common mode of several control units. Synchronising the clocks within the control units in the FlexRay network means that failure of one individual control unit will not influence the communication behaviour of the other control units. Typically, four control units contribute towards synchronisation of the FlexRay. These control units are designated synchronous control units. If more than four control units are included in a FlexRay network, the remaining control units simply synchronise themselves to the time-basis, which is defined by the synchronous control units. Since these additional control units are integrated in a running, synchronous network, they are designated integration control units.The FlexRay in the Touareg 2011 has the following features:● ● ● ● ● ●Electric two-wire bus system Data transfer rate: maximum 10Mbit/s Mixed topology Realtime capability Enables allotted regulations and employment in safety-relevant systems Synchronous transfer14Network structure of FlexRayA FlexRay network could take the form of different network structures (topologies): Star topologyCUBus topologyGWMixed topologyCU CU CU CU CU GW CU CU CU S470_102CUCUCUGWCU CUCUCU CUCU S470_100S470_104Properties for configuring FlexRay topology Control units have 2, 4 or more FlexRay connection pins (daisy chain) Maximum 4 control units on one branch (inc. star) Maximum 12 metre line length per branch Low ohm terminal connection of star and end control unit High ohm terminal connection of intermediate control unitsKey GW Gateway CU Control unit High ohm terminal connection (2400 ohms) Low ohm terminal connection (94 ohms)FlexRay topology in the Touareg 2011Features:J428 J851J850 J533S470_1082 branches Active star in Gateway Max. two control units per branch Daisy chain wiring FlexRay communication only with terminal 15 "ON"Key J428 J533 J850 J851 Control unit for adaptive cruise control Data bus diagnostic interface (Gateway) Control unit 2 for adaptive cruise control Image processing control unit Term. 30, low ohm terminal connection (94 ohms) Term. 15, high ohm terminal connection (2400 ohms) Term. 15, low ohm terminal connection (94 ohms)15Electrical systemData protocolCycle 1Cycle 2Cycle 64....Mini 2....Mini 4Mini 3....Effective data fieldEffective data field S470_112Start field (header segment)Control field (trailer segment)Start field (header segment)Control field (trailer segment)Communication on the bus works with packages of cycles. One package of cycles comprises 64 cycles (320ms). Each cycle from the cycle package is sub-divided into one large static and one small dynamic segment and lasts 5ms. Static segment In the static segment, each control unit has one or more slots (time windows) permanently assigned to it, during which time it can send messages. The quantity and the type of data in this instance is specified for each control unit. This is the deterministic part of the FlexRay, with which assurance can be given that important messages (in the Touareg 2011, those from adaptive cruise control) have been transferred within the prescribed time. Dynamic segment The dynamic segment can be used by a control unit to send additional messages. The communication behaviour in the dynamic segment is not deterministic. If a control unit does not issue a message, the next control unit can send their message straight after the mini slot has elapsed. Currently, the dynamic segment is only used in the FlexRay network of the Touareg 2011 for special developer messages. This segment behaves like an event-controlled data transfer system.16Mini nSlot 2Mini 1Slot 4Slot 3Slot nSlot 1Static segmentDynamic segmentBus physicsChanging from high speed CAN data bus to FlexRay has brought about an increased data transfer rate from 500kBit/s to 10MBit/s. This change also has knock-on effects on the bit time and the bus voltage level.FlexRay[V] 2,8 2,5 2,2 Idle Dominant Data 1 Dominant Data 0 Bus restHigh speed CAN data[V] 3,5 2,5 1,5 Rec. Dominant Recessive Bus restS470_116100ns100ns[ns]S470_1142000ns2000ns[ns]The two lines of the FlexRay are designated bus positive (BP, red) and bus negative (BM, blue). The voltage level of both wires change in this example to minimum 2.2V and maximum 2.8V. The voltage difference is at least 600mV. The FlexRay works with three signal conditions: ● "Idle" – the levels of both bus lines are recessive at 2.5V (idling status). Recessive means that the levels can be overwritten by any other control unit. ● "Data 0" – the BP wire has a low voltage level and the BM wire has a high dominant voltage level. Dominant means that this level cannot be overwritten by other control units. ● "Data 1" – the BP wire has a high voltage level and the BM wire has a low dominant voltage level. With this voltage level configuration, the transfer time for one bit is 100 nanoseconds (ns). If there is no activity (2660ms) on the bus, synchronisation of the control units will be lost and the FlexRay has to resynchronise itself.The two lines of the high speed CAN can bus are designated CAN high (CAN_H) and CAN low (CAN_L) The voltage levels of the two lines alternate between minimum 1.5V and maximum 3.5V. The voltage level difference is 2V. The high speed CAN data bus works with two signal statuses: ● "Recessive bit" – the level of the two bus lines is 2.5V; ● "Dominant bit" – CAN_L has a low voltage level and CAN_H has a high voltage level. With this voltage level configuration, the transfer time for one bit is 2000 nanoseconds (ns).17Electrical systemComparison between CAN and FlexRayFlexRay Time-controlled●CAN Event-controlled● ●● ●The point of time at which the medium can be used is fixed. The period of use of the medium is fixed. Time at which recipient receives message is known.● ●The medium is only used when required. The point of time at which the medium can be used depends on the equipment. Time received is known. Medium may be overloaded.Summary of bus systemsCAN low Data rate Topology Medium Fail-safe feature 100kBit/s Bus Two wire Single wire functionHigh speed CAN 500kBit/s Bus Two wire Not capable of single wireLIN 19,2kBit/s Bus Single wire -MOST 21MBit/s Ring Fibre-optic cable -FlexRay 10MBit/s Bus, stern, mixed Two wire Not capable of single wireRepairs to FlexRay wires can be performed in the same way as CAN bus lines using the VAS wiring repair set.18Convenience electronicsThe 5th generation immobilizerThe new features of the 5th generation immobilizer are purely in relation to the data processes between vehicle and tester via the FAZIT database. The internal process in the vehicle have not been changed. On the 5th generation unit, the FAZIT database makes all decisions online regarding the necessary work measures (one button automatic). The following tester functions are available: Adapting immobilizer Component protection of master (Gateway) combined system Component protection of individual componentsWith the component protection master function, the Gateway is programmed and authorised as a component protection master by FAZIT. This is a key control unit for the following component protection activities among individual components.Component protection listing for individual components: 90 - Component protection for reversible belt tensioner on front right 13 - Component protection for cruise control 05 - Component protection for access and start authorisation 15 - Component protection for airbag control unit 06 - Component protection for front passenger seat adjustment 36 - Component protection for driver seat adjustment 56 - Component protection for radio 17 - Component protection for dash panel insert 47 - Component protection for sound system 08 - Component protection for Climatronic control unit 09 - Component protection for onboard supply control unit 19 - Component protection for data bus diagnostic interface 88 - Component protection for cruise control 2 0E - Component protection for media player 1 5F - Component protection for information electronics 8F - Component protection for reversible belt tensioner on front left The above named control units must be authorised online by FAZIT as otherwise the control unit will be impaired in its functionality to some degree.To quickly check whether a component protection control unit works, it can also be swapped over providing it works with terminal 30. However, the ignition should not be switched on as otherwise interrogation by the Gateway will ensue in terms of component protection.19Convenience electronicsThe onboard supply control unitsOn the Touareg 2011, management of the onboard supply and convenience functions are shared by onboard supply control unit J519 and convenience system central control unit J393.Onboard supply control unit 1 J519FunctionLight functions● ● ● ● ●S470_040Air conditioner functions● ●Exterior light master, actuation of lights Turn signal slave, actuation of front turn signals Interior light master Leaving home and manual coming home Interior and control lighting● ●Driver information● ● ● ● ● ●●Front seat heating (not with climate seats) LIN Gateway for seat heater/seat ventilation control LIN Gateway for pressure sensor and AQS Actuation of air conditioner compressor (not hybrid) Humidity sensor via LINExterior temperature, unfiltered Brake pad/lining wear warning Brake fluid warning Coolant warning Washer water warning Light warningOther functions● ● ● ● ●Wash/wipe● ● ● ●● ●Actuation of wiper via LIN Rain sensor via LIN Actuation of washer/dual washer pump Actuation of HWS pump●Actuation of horn relay Servotronic with actuation of valve Read-in reversing light switch Read-in bonnet contact Read-in bonnet contact for ESI LIN Gateway for UGDO sender Eco start/stop button, actuation of LED E-mode button, actuation of LEDInterfaces to J393●●Authorisation for electric steering column lock (discrete and CAN) Hardware feedback terminal 15 (CAN signal)20Convenience system central control unit J393FunctionLight functions● ● ● ●S470_008Immobilizer● ● ●Exterior light slave, actuation of rear lights Brake light actuation Turn signal master Luggage compartment light actuationImmobilizer master Read-in transponder of EIL via LIN Actuation of ESL via LINOther functions Central locking and ATA● ● ●● ● ● ● ● ●Central locking master Radio remote control (315MHz, 434MHz, 868MHz) Tank flap engage and release Luggage compartment release Power latch actuation Convenience opening/closing Window regulator and sliding roof authorisation ATA, actuation of sounder and IRM/TS● ● ● ● ● ● ●External socket relay External rear window heater relay PSR via LIN Convenience opening, convenience turn signalling Exterior mirror actuation Crash signal evaluation LIN Gateway for UGDO operating unit Self-diagnosisTerminal control● ●Kessy● ● ●Keyless Entry and Keyless Go Read-in ignition/starter button Actuation of Kessy aerials● ●S-contact, term.15, term.50, term.75 Read-in electronic ignition lock Actuation of key withdrawal lock Engine ECU wake-up functionThe abbreviations used here are explained in the glossary and can be looked up there. In other technical literature, J519 is also designated body control module 1 (BCM 1) and J393 is also designated body control module 2 (BCM 2).21Convenience electronicsSpecial functionsJ519●J393●●●●●P-mode: HWS, day driving lights, interior light and seat heating inactive BEM deactivation stages: Interior light, footwell lights, CH/LH, day driving lights, main beam inactive Transport mode: Interior light, footwell lights, CH/LH, day driving lights, main beam, fog light, rear wiper inactive Component protection (participants): Interior light, seat heating inactive Flashing via tester (as standard throughout product range)●●● ●P-mode: Rear window heater and luggage compartment light inactive BEM deactivation stages: Sockets and luggage compartment light inactive Transport mode: Sockets, luggage compartment light, rear roller blind, ATA, Kessy inactive Component protection Flashing via tester (as standard throughout product range)The electronic ignition lockAn electronic ignition lock finds its debut in the new Touareg. This ignition lock is a new design. Part of this involved converting the mechanical turning principle into a version that senses what position the key has been turned to electronically.DesignThe new remote key fob has no key as such but three buttons to unlock and lock the vehicle and also to open the rear lid. If the VW emblem is pressed along with an additional retaining lug, an emergency key pops out on the rear. This serves as a means of unlocking the vehicle in an emergency if the battery in the fob is discharged. The remote key fob also has a mounting for a key ring. The battery lid can be found behind the chrome clasp of the remote key fob.S470_00722FunctionInserting remote key fobTo start the vehicle, the remote key fob is inserted into the opening until it engages securely. In this first position the infotainment components, such as radio and navigation system are activated as the S-contact is actuated when the fob is inserted. If the remote key fob is just inserted but not turned, it can simply be withdrawn again. The key lock is not active in this case.S470_009Turning remote key fobWhen the remote key fob is turned from the start position (engine on or ignition on) it is locked mechanically to hold it securely in the ignition lock. To start the engine, the remote key fob is turned clockwise or anti-clockwise - both directions are possible - onto the relevant switch contact (stop). The remote key fob always returns automatically to the start position. If just the ignition is to be switched on, this is performed with the same turning motion of the remote key (clockwise or anti-clockwise) but without the prerequisite for engine start authorisation, i.e. brake pressed (automatic gearbox/DSG) or clutch pressed (manual gearbox).S470_011To switch the engine off, the key is turned clockwise or anti-clockwise again. The ignition is switched off again in the same way. When doing so, the remote key fob is electromechanically released and can be withdrawn.If the vehicle battery is discharged, removal of the mechanically locked remote key fob is still possible via the specially designed mechanical emergency release device in the ignition lock.23Convenience electronicsThe area view sensorsThe area view sensors form the basis of the driver assist systems. The Touareg 2011 features several radars and camera sensors that monitor the surrounding area, which is analysed and interpreted using intelligent algorithms.Ultrasound frontMultifunctional front cameraUltrasound rearRadar, frontRadar, rearS470_012●●●●The Touareg is equipped at the front with two 77GHz radar sensors with a range of 200m. These are used for the adaptive cruise control (ACC) and Front Scan. A multifunctional front camera serves: - to detect vehicles (invisible to radar) - to monitor the area in front of the vehicle when stationary (automatic restart of ACC) - to detect lane information for lane departure warning. - to detect vehicles and other illuminated objects at night for dynamic light assist. In the rear area there are two further radar sensors (24 GHz) that scan the traffic situation behind the vehicle. They form the basis for lane change assist, the signals of which are used in addition by ACC and Front Scan. To aid parking, the Touareg is equipped with two 4-channel ultrasound systems. The information from the ultrasound sensors is also used for ACC regulation.24Driver assist systemsThe multifunctional camera systemWith the camera control unit J852, the multifunctional camera forms one assembly unit. With the operating and display protocol (ODP), the camera control unit J852 sends information via the extended CAN data bus to be used by the light assist systems and the lane departure warning system. If the Touareg is fitted with adaptive cruise control (ACC), the control unit for image processing J851 is also included. J852 receives the image information via a fast LVDS line (Low Voltage Differential Signalling). This control unit sends the safety-relevant signals along the fast FlexRay data bus and supplies the control units for cruise control J428 and J850, which are also located in the FlexRay network, with the details derived from the image information. To calculate the dive angle of the vehicle about the Y-axis with greater speed and safety, the camera control unit has a dive rate sender at its disposal, which is connected via the extended CAN.Dive rate sender G752 FlexRayData bus diagnostic interface J533Extended CANLVDS (Low Voltage Differential Signalling) S470_016 Control unit for image processing J851 Camera control unit J85225Driver assist systemsThe multifunctional front cameraS470_034S470_024The multifunctional front camera is integrated into the mirror base. It has the following features: It is a colour camera with a resolution of 1024 x 512 pixels. The range, depending on the system, can be up to 800m. The horizontal opening angle is 42 degrees and the vertical angle is 21 degrees.The camera in the Touareg serves several systems. It supplies image information at different ranges for the following driver assist systems: Adaptive cruise control (ACC) with Front Scan with reduced stopping distance 3 (60m) Lane departure warning (80m) Dynamic light assist (DLA) (400/800m) Traffic sign/marking recognition (later introduction)The dive rate sender G752Direction of travelS470_020S470_022The dive rate sender G752 is located on the rear right (in direction of travel) beneath the bench seat support panel. It provides the vehicle's rate of rotation about the lateral axis (y-axis) and transfers this signal via the extended CAN exclusively to the camera control unit J852.The dive angle calculated from this is needed by the camera for the image processing functions. The dive rate sender is not capable of self-diagnosis and does not have its own diagnosis address. Diagnosis is possible via the camera control unit J852 with address code 85.26The adaptive cruise controlAdaptive cruise control, sometimes referred to as automatic cruise control (ACC), with double radar and Front Scan is an enhancement of the conventional cruise control system (CCS).Description of systemDisplay in dash panel insert Target vehicle detectedThe adaptive cruise control system keeps the vehicle travelling at a previously selected speed, which the driver can set for open roads at 30-250km/h and for following at 0-250km/h. The adaptive cruise control system also ensures that a preset distance from the vehicle travelling ahead is safely maintained. In this case, the speed of the vehicle is adapted to the speed of any vehicle travelling ahead. The speed can be set in four stages (from approx. 1 -2.5sec.). Furthermore, the driver has three driving programmes to choose from: "Standard", "Comfort" and "Dynamic". If the road ahead is clear, the vehicle is accelerated up to the desired speed. If there is a vehicle travelling ahead at a slower speed in the same lane, the system adapts to allow the vehicle to match that speed with a preset distance.Specified distanceActual distanceS470_003 Desired speedLane detection by the camera, route data from the navigation system and detection of stationary vehicles and vehicles travelling ahead by both front radars ensures an improved estimation of which path to follow to continue the route. If a turn signal is activated, the system detects the driver's intention to overtake and improves the system dynamics with consideration for following traffic.Stop&Go functionIf the vehicle travelling ahead slows down to a halt, the Touareg will brake automatically and stop behind the vehicle. If the vehicle ahead resumes its journey within three seconds, the Touareg will follow it likewise automatically. If the stationary period lasts longer than three seconds, the driver can activate a time window of 15 seconds by pressing the RES button in the steering column switch enabling the Touareg to follow the vehicle ahead automatically within this period. With the gap close function (press RES button, both vehicles stationary), the gap to the vehicle ahead can be closed comfortably.27Driver assist systemsFront ScanFront Scan in the Touareg is not just an assist function with a warning that is designed to prevent collision accidents, it also offers, in its third generation, a means of braking the vehicle (also without driver intervention). This contributes towards reducing the accident severity. Under certain conditions (speed-dependent), the system may be able to avoid the accident. This automatic emergency braking function (ANB) is achieved by reduced stopping distance RSD3. It accompanies reduced stopping distance RSD1 and reduced stopping distance RSD2 to form part of Front Scan.Reduced stopping distance RSD3Following the warning jolt from reduced stopping distance 2, the system decelerates at a rate of 3m/s2 until a reaction period of has elapsed. If the driver does not brake sufficiently, the system will intervene with additional braking. If the driver does not respond at all, the deceleration rate is increased to 5m/s2. If a collision is unavoidable, the system will initiate emergency braking, providing the following traffic is not put at risk, with maximum deceleration up to 9m/s2. In this instance, an overall speed reduction of 40km/h is engineered to reduce the accident severity. While this increased deceleration is taking place, the following traffic is made aware of the situation by the hazard warning lights (emergency flashing).S470_056 RSD3: Deceleration with 5 m/s2 ANB: Emergency braking with 9m/s2 RSD2: Warning jolt RSD1: Highest sensitivity of brake assist RSD3: Deceleration with 3m/s2 RSD2: Optical/acoustic warning RSD1: Prefill RSD1: Increased sensitivity of brake assistFurther information about reduced stopping distance RSD1 and RSD2 can be found in self-study programme no. 374 "Traction control and assist systems".28System designThe adaptive cruise control system is a functional highlight. A combined system of up to 27 control units provides even greater comfort and safety. A new feature of the adaptive cruise control system in the Touareg 2011 is not just that this assist system is one function spread over several control units but also that other assist systems with completely different tasks can be included in the operation. In this instance, for example, these are the radar sensors from the lane departure warning, the multifunctional camera system, which is used, among other things, to keep the vehicle in lane, and also the ultrasound sensors from park distance control. All of the components and systems mentioned serve as a means of monitoring the area in front of and behind the vehicle and identifying potential obstacles. They are described briefly as follows.Ultrasound sensorsThe signals from the ultrasound sensors are used to resume travel on the new Stop&Go function.Multifunctional camera systemThe multifunctional camera system serves as a supplier of redundant signals to determine plausibility of the signals from the front radar sensors. As before, the system bridges the detection gap between ultrasound sensors and radar sensors. Using the camera with its 60m range for the ACC and RSD3 functions and the navigation data (with unrestricted "view"), an improved forecast of what path the road is taking and information about the number of lanes is provided in addition to reduced neighbouring lane interference. Thanks to the colour camera, coloured markings are detected more easily (even different coloured road markings overseas).29Driver assist systemsFront radar sensorsThe front radar sensors are located next to the fog lamps. They are 3rd generation radar sensors with the following features:● ●●● ●Integrated in the sensor are 4 radar aerial units. They work based on the long range sensor principle with a sender frequency of 77GHz. The installed sensor heater works in a temperature range of -5°C to +5°C. The radar sensor range is 200m. The horizontal opening angle is 40 degrees.S470_036With this new generation of radar sensors, the whole width of a 3 lane road can be scanned even from a distance of approx. 30 m.S470_0284 aerial units per radar sensorSenderReceiverS470_00230System functions of ACCDetection of lane changeThe multifunctional camera system detects an impending lane change by the vehicle travelling ahead as it approaches its lane boundaries. Stored in the camera system are various characteristics, which enable the system to differentiate between car, truck or motorbike. The lane change is detected irrespective of whether the vehicle travelling ahead enters or exits the same lane as the camera system.Detected rear views of vehicles travelling aheadDistances to detected lane boundaries S470_005This information is transmitted to the ACC system, adopted by it in its calculation algorithm and serves as a means of determining, with greater precision, what is happening ahead.Obstacle detection in close proximityThe information from the multifunctional camera system and the ultrasound sensors for obstacle detection is required mainly for the close proximity (within 5m) to make it easier to resume travel. In this range, the radar sensors are not capable of detecting the whole area due to their radiation characteristics and their opening angle.Monitoring following trafficIf a "no following traffic" message has been issued, the rear sensors enable Front Scan to increase the deceleration rate of 3m/s2 to maximum 9m/s2 during brake intervention following a driver warning.31Driver assist systemsLane departure warningS470_013Lane departure warning helps the driver keep the vehicle in lane. The system comprises a camera in the roof module holder, the displays in the dash panel insert and a vibration motor in the steering wheel. With the aid of the camera (range for this function 80m), the lane boundary markings are detected. If the vehicle appears to be departing the lane unintentionally, the driver's attention is drawn back to the traffic situation by means of a steering wheel vibration.Area of use● ● ●Motorways and major roads Activation speed 65km/h to 250km/h During deceleration, the system remains active up to 60km/h● ● ●Curve radius 250m Lane widths of 2.5m to 5.0m A lane marking on one side is sufficient to detect the lanePoor conditions, such as insufficient road markings, dirty or snow-covered road surfaces, excessively narrow lanes or even ambivalent road markings, as is often the case when road works are being carried out on the motorway, lead to the system being temporarily incapable of providing a warning.32OperationSwitching on and offThe lane departure warning system is switched on and off with the button for driver assist systems on the front of the turn signal lever and by activating the buttons in the menu of the dash panel insert. If the lane departure warning system detects clear road markings within its system limitations, it changes from a passive (at least one condition has not been met) to an active operating mode. The control lamp indicates the operating status of the lane departure warning system.The lane departure warning control lamplane departure warning switched offlane departure warning switched on and in passive modeLane departure warning switched on and in active modeS470_072S470_074Adjusting warning levelThe driver can choose from three different warning levels via the touchstone of the infotainment system:●●Early warning level Normal warning levelLate warning level●Early warning level: The virtual boundary is set approx. 20cm before the lane marking. Normal warning level: The virtual boundary is the same as the lane marking. Late warning level: The virtual boundary is set approx. 20cm after the lane marking.When the virtual boundary is driven over, a warning is issued.33Driver assist systemsSystem designNetworkingV331Key E221 J527 J533 J852 V331 h k L Operating unit in steering wheel Steering column electronics control unit Data bus diagnostic interface Camera control unit Steering vibration motor Extended CAN data bus Convenience CAN data bus LIN data busPWME221LkJ527 J533 J852S470_120 hSteering vibration motorThe steering vibration motor V331 is located in the bottom spoke of the steering wheel and is actuated by the signal from the camera control unit J852 via CAN and by the steering column electronics control unit via LIN. The driver can choose from three vibration levels with different frequencies: Weak level – 29hz Medium level – 34hz Strong level – 44hzS470_063These levels are adjusted via the touchscreen of the infotainment system. The different frequencies are achieved by PWM signal actuation to the steering wheel vibration motor E221.S470_076 Steering vibration motor34System functionWhen the lane departure warning system is switched on, the system starts to scan and evaluate the path the road follows in front of the vehicle via the camera. If the vehicle gets close to a recognised boundary line and there is a threat of it departing the lane, the driver is warned by a vibration in the steering wheel. The system only warns once. A second warning is only issued if the vehicle has moved sufficiently away from the relevant boundary line and has then approached it again. In this way, it is possible to avoid continual warnings while driving parallel to a road marking. If, while the system is active, a turn signal is activated before a boundary line is driven over, the warning is suppressed as the system assumes that the lane departure is intentional. Aside from the steering wheel vibration, the driver of the new Touareg can see a visual representation of detected and violated (driven over) boundary lines in the display of the dash panel insert.System messagesActive mode: - Road marking detected on left and rightActive mode: - Road marking detected on left and right - Warning threshold on right exceededS470_062S470_068Active mode: - Road marking detected on right - Road marking not detected on leftActive mode: - Road marking detected on right - Road marking not detected on left - Warning threshold on right exceededS470_070S470_064Passive mode: - Road marking not detected on left and rightA warning is only issued in the case where a road marking is detected on one side if the boundary on that side is violated.S470_06635Driver assist systemsThe dynamic light assistThe dynamic light assist (DLA) from Volkswagen (also designated "masked permanent main beam") is debuted in the new Touareg. It is based on the already existing systems dynamic cornering light and headlight range control. With the dynamic light assist function, the road and edges of the road are illuminated to maximum effect while, at the same time, preventing any dazzling of vehicles travelling ahead in the same and opposite direction. The DLA is therefore currently the most innovative development level for headlight systems with variable light distribution.FunctionExample of change in light distribution of headlight due to automatic detection of approaching objects with activated/recognisable lighting.Illumination without object in opposing laneIllumination with object in opposing lane - distance to object farIllumination with object in opposing lane - distance to object mediumIllumination when passing an object in the opposing lane In the final approaching phase, the "masked main beam" from the left headlight is equal to the dipped beam position.S470_058S470_058a to 058d36Activation conditions: Light switch in "Auto" position Main beam actuated DLA switched on via touchscreen of infotainment system. Dark (signal from rain and light sensor G397) Speed 60km/hExample of change in light distribution of headlight due to automatic detection of objects travelling ahead with activated/recognisable lighting.Illumination without object in own laneIllumination with object in own lane - distance to object farIllumination with object in own lane - distance to object mediumS470_060Illumination with object in own lane - distance to object close In the final approaching phase, the "masked main beam" from the right headlight is equal to the dipped beam position.S470_060a to 060d37Driver assist systemsNetworkingJ667LKey E1 G752 J285 J519 J527 J533 J667 J668 J685 J745 J794 J852 Light switch Dive rate sender Control unit in dash panel insert Onboard supply control unit Steering column electronics control unit Data bus diagnostic interface Power output module for left headlight Power output module for right headlight Display unit for front information display and operating unit control unit Cornering light and headlight range control unit Control unit 1 for information electronics Camera control unit Display and operation CAN data bus Extended CAN data bus Convenience CAN data bus LIN data bus MOST data busJ668 J745 G752 J852hkE1 J519 J527mJ533 J285 J794LVDS S470_118 bb h k L mJ685The dynamic light assist is based on the intelligent interplay of multifunctional front camera and camera control unit J852, image processing software and top Xenon headlight. With the front camera, vehicles travelling ahead (camera range 400m) and those approaching from the opposite side (camera range 800m) are detected providing their lights are on. This information is digitally evaluated and the exact position and width of the detected vehicles is determined. The system also distinguishes between street lamps, traffic lights or reflections from side marker posts. This information is sent to the control unit for cornering light and headlight range control. Together with other vehicle information, such as speed, steering wheel angle or general lighting conditions, the optimal light distribution is thereby calculated automatically and depending on the situation and then sent to the headlight control units. These are installed directly onto the headlights. They have the same design and the same part number. The control units can determine whether they control the left or right headlight by means of the connector coding. Based on the calculated light distribution, a special roller-type mask is now moved between the light source and projection lens in the top Xenon headlight. This prevents anyone from being dazzled, i.e. other traffic users are kept out of the light distribution.38Top Xenon headlightThe top Xenon headlight in the Touareg 2011 is the first headlight with permanently masked main beam.S470_037S470_038Xenon burnerReflectorRoller-type maskLensS470_078S470_080The function of the dynamic light assist is realised by the additional, rotating, roller-type mask (shutter) between the reflector with the xenon burner and the lens. In connection with intelligent actuation of the left and right headlight, this additional masking geometry allows light to be masked only when it could dazzle others. Even with the DLA switched off, the mask ensures that the dipped beam and main beam functions can be activated. Furthermore, in the dipped beam position it allows the functions urban light, main road light and motorway light.39Driver assist systemsArea ViewThis driver assist function is debuted at Volkswagen in the Touareg 2011. Area View is a camera-based area capture system and is an enhancement of the reversing camera familiar from the A and B class (Rear Assist). While the reversing camera covers the area behind the vehicle, Area View allows the driver to see the entire area around the vehicle. It offers the driver numerous views and setting modes that he/she can specifically select depending on the traffic situation and according to the information he/she requires.Design of Area View systemControl unit 1 for information electronics J794 and display unit for front information display and operating unit control unit J685 Area view camera control unit J928Visual range of right mirror camera R245Visual range of rear camera R246Visual range of front camera R243 Visual range of left mirror camera R244 S470_010Capturing the view around the vehicle is achieved by four cameras that are integrated cleverly within the vehicle. The front camera is located in the front grille, the rear camera is in the handle of the rear lid and the side cameras are installed underneath the side mirrors. The cameras have wide-angle lenses and capture the whole area around the vehicle, thus enabling areas to be viewed that are either difficult to see or cannot be seen at all. Since the camera capture areas overlap, an accurate and realistic optical transition between the visual ranges of neighbouring cameras can be created (so-called bird's eye view with complete area capture). The system has the diagnosis address of the reversing camera system (6C).40NetworkingR244 R243 k LVDS J928 L J345 J519 L J393 L a J527 L J387 L J217 J386 J533 m G85 J104 G419 fw b J285 J446 R* CVBS LVDS J685 J388 J794 J389 E221 D G397 J400 R245 R246Key D E221 G85 G397 G419 J104 J217 J285 J345 J386 J387 J388 J389 J393 J400 J446 J519 J527 J533 J685 Ignition/starter switch Operating unit in steering wheel Steering angle sender Rain and light sensor ESP sensor unit ABS control unit Automatic gearbox control unit Control unit in dash panel insert Trailer detector control unit Driver door control unit Front passenger door control unit Rear left door control unit Rear right door control unit Convenience system central control unit Wiper motor control unit Parking aid control unit Onboard supply control unit Steering column electronics control unit Data bus diagnostic interface Display unit for front information from display and operating unit Control unit 1 for information electronics Area view camera control unit Radio RCD 550 (introduced later, excluded with J794) Front area view camera Left area view camera Right area view camera Rear area view camera Powertrain CAN data bus Display and operation CAN data bus Chassis CAN data bus Convenience CAN data bus LIN data bus MOST data busJ794 J928 R* R243 R244 R245 R246 a b fw k L mS470_122The cameras are connected via HSD wires (High Speed Data) to the area view camera control unit. These wires are used to supply power to the cameras, to control them and to transfer video signals per LVDS (Low Voltage Differential Signalling). The connection between the area view camera control unit and the information electronics control unit 1 is by means of coaxial cable (CVBS - composite video signal). The data transfer rate of the CVBS connection is approx. 6MBit/s. The area view camera control unit relies on a wide range of signals from other control units. The accrued signals are just displayed optically by the area view camera control unit without having any functional influence or effect on other systems (e.g. display of dynamic steering angle dependent guidelines).41Driver assist systemsVGA cameraArea View has four cameras with wide-angle lenses with the following technical features:● ● ● ●Resolution: 640 x 480 pixels (VGA resolution) Opening angle: 190° (greater than half space) ¼ inch CMOS imager chip as sensor Temperature range: from - 40 to 85°CS470_006Area view camera control unit J928The control unit has the task of processing the images supplied by the cameras and preparing them for display on the RNS 850 screen or radio version RCD 550 (which will be introduced at a later stage). This includes removing any distortion from the supplied images, converting or changing to individual perspectives and also displaying static and dynamic guidelines.S470_004The area view camera control unit works with a microcontroller to regulate the processes and a 600 MHz DSP (digital signal processor) to process the camera images.42OperationBy engaging reverse gear or pressing the parking aid button, the relevant view is shown on the display of the radio or navigation system with touchscreen and has a mini bird's eye view on the left of the display. In the mini bird's eye view, the detailed perspective can be selected by touching the relevant area (front, rear, left or right of vehicle). By touching the roof of the vehicle in the mini bird's eye view, the whole view of the vehicle from above is displayed. Once the relevant region is selected in the mini bird's eye view, the display changes to split screen. A detailed view of the selected area around the vehicle is then shown in the right half of the display. In a second step, softkeys in the pulldown menu on the right side of the screen can be used to select different views. In the mini bird's eye view shown on the left, the camera selection and thereby camera perspective can be selected.Example view if rear sector is selected Bird's eye view Camera selection Front Side Rear Softkeys: Parking bay Parking gap Trailer support Traffic passing behindS470_082Display of selected camera-specific viewThe display contents shown correspond to the infotainment system with German system setting and serve merely as an example. Please refer to the corresponding operating manuals for the text contents shown on the display in the relevant national languages.43Driver assist systemsFunctionArea View works in a speed range from 0 to 15km/h. The cameras capture the area around the vehicle once activated. The captured images are straightened out by the area view camera control unit because the raw images from the wide-angle lens cameras are heavily distorted. The angle of view is then adapted to the desired perspective, also by means of image processing. Finally, this corrected image is enhanced with guidelines depending on the selected view to show the distances and to project the path ahead. This prepared image is then shown on the RNS 850 display or the display of radios to be introduced at a later stage.If there is a visible distortion of the image in the area where neighbouring camera views overlap, the system has to be recalibrated in the workshop. The inspection for image distortion must be performed once the air suspension has settled at normal level and with the dampers set to "Comfort".GuidelinesDepending on the selected view, static and dynamic guidelines are displayed. These guidelines make it easier to estimate distances (red and green guidelines) and show the potential path depending on the steering angle (yellow guidelines).0.4m1m2m2m1m0.4mS470_13244Display viewsBird's eye view Display view From the four camera images, the control unit calculates an overall view of the area surrounding the vehicle as seen from above through a virtual camera. A high quality image is generated here and particular attention is given to optimising the transitions between the four camera views. In this view, a silhouette of the vehicle as seen from above is superimposed. The driver is thereby allowed to see the area around the vehicle from a bird's perspective, also referred to as bird's eye view.S470_084"Cross traffic" view Situation This function allows the driver to look 90 degrees to the left and right from the front point of the vehicle, i.e. basically to look around the corner, to assess the traffic situation. Despite the fact that the driver is sitting in the vehicle about 2 metres behind the front camera, this system now allows him/her to see what is happening ahead on the left and right. Area View supports the driver here at exits that are difficult to see and in narrow roads. For the "rear cross traffic" view, the rear camera is used. It allows the driver to see what is happening from the rearmost point of the vehicle.S470_021Display viewS470_08645Driver assist systems"Parking bay" view Situation This view supports the driver when driving forwards or backwards into a parking space, whereby the front camera or rear camera is used respectively. When parking forwards, the view is activated by pressing the park distance control button. When parking backwards, the view is activated by engaging reverse gear. Display viewS470_041S470_088"Left and right side" view Situation With this view, side cameras support the driver, e.g. when parking or on offroad tracks. Static guidelines indicate to the driver the distance to an obstacle, e.g. a curb. Both side views can also be activated simultaneously via the side softkeys.S470_045Display viewS470_09046"Trailer support" view Situation This view makes it easier for the driver to hitch up a trailer. The rear camera is used for this function. The driver sees the area behind the vehicle from above. Green guidelines in the image provide a means of assessing the distance from the hitch to trailer. A yellow line shows the driver in which direction the vehicle will move with this steering angle. Hitching up the trailer to the vehicle is thereby optically supported. To display this view, it is necessary to toggle in the menu. Simply deploying the trailer hitch or hitching up the trailer will not result in the perspective being selected.S470_025Display viewS470_092"Offroad" display Situation This view supports the driver when driving offroad and if difficult obstacles are encountered by displaying the area directly in front of the vehicle from a bird's eye view.S470_029Display viewS470_09447InfotainmentAt launch, the Touareg can be equipped with an infotainment system based on the RNS 850 radio and navigation system. An infotainment system based on the RCD 550 radio is planned for a later date. The functions and information in this book therefore refer only to the system combined with the RNS 850.Overview of infotainment systemThe central element is the control unit 1 for information electronics J794 for the RNS 850 in the versions with and without integrated GSM telephone module. J794 communicates with most infotainment components via the MOST data bus. Further components could be, for example: the radio R (radio unit in the "Basic" and "DAB" versions) the DVD changer R161 the TV tuner R78 (TV/DVB-T tuner; depending on country in analogue/digital and purely digital versions) the digital sound package control unit J525 (DYNAUDIO sound package)J285 J794 R199 ab J533c J685de R161-R J525 R78 S470_500As display units, the screen in the centre console (display unit for front information display and operating unit control unit J685) and in the dash panel insert (control unit in dash panel insert J285) are connected to the infotainment system via different interfaces.Key J285 J525 J533 J685 J794 R R78 R161 R199Control unit in dash panel insert Digital sound package control unit Data bus diagnostic interface Display unit for front information display and operating unit control unit Control unit 1 for information electronics Radio TV tuner DVD changer Connection for external audio sourcesa b c d eLVDS connection (200Mbit/s) Display and operation CAN data bus (500kbit/s) MOST data bus (21Mbit/s) Powertrain CAN data bus (500kbit/s) Extended CAN data bus (500kbit/s)48The DYNAUDIO sound systema a Key a b b 60mm treble loudspeaker 100mm mid-range loudspeaker cone 200mm bass loudspeaker 50mm treble loudspeaker Digital sound package control unit Internal microphone (in roof module)bc c c d J525 J525 c c R74a 5 loudspeakers on lefthand side of vehicled b R74aS470_0465 loudspeakers on right-hand side of vehicle 2 loudspeakers in centre of dash panel MOST data busThe central element of the DYNAUDIO sound system is a 620 watt amplifier with surround control (digital sound package control unit J525). It is fitted in the luggage compartment near the left-hand wheel housing and has 10 output stages for connecting a maximum of 12 loudspeakers. The amplifier communicates with the infotainment system via the MOST data bus. A microphone built into the roof module detects the noises in the interior. These noises are analysed by the amplifier electronics and the playback signal is then adjusted depending on the frequency and sound level. This process is called automatic playback signal adjustment. The surround control (Dolby 5.1, if supported by the data medium) allows you to set up an optimum surround sound, which faithfully reproduces, for example, concert hall acoustics, in relation to your position inside the vehicle.Further information about the infotainment system can be found in self-study programme no. 473 "Infotainment in the Touareg 2011".49GlossaryABS Anti-lock braking system Counteracts potential locking of the wheels when the vehicle is braked hard by reducing brake pressure. ACC Adaptive cruise control, also called automatic cruise control (ACC), is an enhanced version of the conventional cruise control system (CCS). ANB Automatic emergency braking AQS Air quality sensor RSD Reduced stopping distance ODP The operating and display protocol ODP is used for communication between function control units and operating and display control units. ODP consistently separates the function from the display and control. BCM Body control module In the Touareg, either the onboard supply control unit J519