TECHNICAL DOCUMENTATION

SSP 492 The Jetta 2011 EU

PDFEN64 pages5 MB
SSP 492 The Jetta 2011 EU - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingSelf-study Programme 492The Jetta 2011 EU The Jetta 2011 EU – Design – Technology – ComfortThe Jetta model year 2011 is being launched in the EU market and builds on the success story of its predecessor. It successfully continues the modern style of Volkswagen Group combining it with modern technology and a high level of comfort. Thanks to the good balance of technical equipment and comfort features, it is excellently equipped for a wide range of market and customer requirements.S492_002The features of the new Jetta are:● ● ● ●an elegant and, at the same time, sporty design a high level of quality very good handling an optimised body structure●● ●greater comfort thanks to greater interior and exterior vehicle dimensions very good vehicle dynamics and new chassis configurationSeparate self-study programmes are available on the following current topics:● ● ●Self-study programme no. 308 “The Direct Shift Gearbox 02E” Self-study programme no. 390 “The 7-speed Dual Clutch Gearbox 0AM” Self-study programme no. 403 “The 2.0 ltr. TDI Engine with Common Rail Injection System”The self-study programme portrays the design and function of new developments. The contents will not be updated.For current testing, adjustment and repair instructions, refer to the relevant service literature.Important Note2 ContentsIn Brief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Occupant Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Engines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Running Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Electrical System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Heating and Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Radio, Telephone and Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543 In BriefWhere is the Jetta 2011 EU produced?The Jetta 2011 EU is produced at Volkswagen’s Puebla plant in Mexico. This factory opened in 1964 and initially produced the VW Beetle. The Puebla site currently has a workforce of around 15,000; they build among others – the New Beetle, – the Jetta – and the Golf Estate (also as Jetta Estate for some markets). The Jetta 2011 EU replaces the Jetta 2006.S492_006S492_005At the Puebla plant, which is equipped with the very latest technology, a constantly high quality standard is guaranteed by modern production lines combined with a modular manufacturing strategy. The plant is one of Volkswagen’s leading production sites. The engineers at Puebla played a major role in the preparation and development stages of the new Jetta as well as in the preparations for the actual production. The Jetta 2011 EU is built with the existing production facilities for the Jetta 2006 in Mexico.4 History of the JettaThe Jetta series can look back on a long success story that now stretches back 30 years. This not only concerns the vehicle’s technology and exterior appearance, but also the model name. After temporary changes of name, the model series has been produced again under the internationally very successful “Jetta” name since the fifth generation.1979 – Launch of model series – Jetta 11984 – 2nd generation – Jetta 21992 – 3rd generation – Vento1998 – 4th generation – Bora2005 – 5th generation – Jetta 20062010 – 6th generation – Jetta 2011 EUS492_0495 In BriefThe Jetta 2011 EUIn many disciplines, the Jetta 2011 EU sets standards in its class, e.g. in terms of: – – – – – – – Safety Design Quality Handling Ride comfort Spaciousness Functionality● ●High-quality dash panel with soft surface using slush technology●New tyre pressure monitorNew headlight design●Electronic Stabilisation Programme ESP MK60 EC●Optimised front axle with subframe and transverse links made from steel●Electromechanical power steering●Air-conditioning system or 2-zone Climatronic6 ●Optional “Keyless Access” locking and starting system – start with “Engine” starter button●New rear light designS492_004●Optional optical parking system●Optional start/stop system●Rear axle with four-link suspension●Increased front and rear track width improves vehicle dynamics significantly7 In BriefTechnical dataJetta 2011 EUS492_056S492_057S492_058 The dimensions given in the pictures are in mm.Length Width Width with exterior mirrors Height Wheelbase4,644 mm 1,778 mm 2,020 mm 1,453 mm 2,651 mmTrack width at front Track width at rear Kerb weight Permissible gross vehicle weight Drag coefficient1,535 mm 1,532 mm 1,272–1,464 kg 1,820–1,950 kg 0.3 Cd8 S492_059S492_060The dimensions given in the pictures are in mm.Front headroom Rear headroom Interior length Driver shoulder space Front passenger shoulder space1,014 mm 943 mm 1,797 mm 1,401 mm 1,362 mmTank capacity Luggage compartment volume55 litres 510 litres9 BodyBody structureThe body structure of the Jetta 2011 EU has been systematically further developed particularly in terms of requirements for● ● ● ● ●lightweight construction vehicle safety sportiness comfort and qualityS492_009A considerable weight reduction has been achieved compared with the previous model. At the same time, the new body structure provides an all-round high level of crash safety and body stiffness superior to the competition. The weight reduction achieved supports the efforts of Volkswagen Group to reduce CO2 emissions.Lightweight constructionThe lightweight construction aims have been met with●● ●optimum use of ultra-high-strength and thermoformed steels reduction of panel thicknesses and refined design optimised through computer modellingThis therefore breaks the generally recognised trend of “larger, more comfortable vehicles being heavier” in a convincing manner. The weight-reducing measures can be divided into three groups.●The main part of the reduction results from widespread use of thermoformed parts in the floor structure, the B-pillar and the roof frame. One further important measure is the reduction of the material thickness of body parts that are subjected to lighter loads, for example, the outer skin parts – the performance characteristics are retained, however. In the third measure, the engineers made sure that positive effects to save weight were created in the body configuration throughout the design phases. For example, weight can be saved with clean profiles and smaller reinforcements in the “right places”.●●10 Material qualities and their proportions in the body structureStrengths of steel sheets Proportion of steel sheet according to strength (related to legend on left) 220MPa 420MPa 1,000MPa13 %46 %41 %S492_010Laser soldering seamWelding methodsThe proven spot welding process is mainly used for joining body components.Laser solderingLaser soldering is used in the roof area for joining the side panel to the roof and also on the rear vertical end piece of the rear lid.Laser soldering seam Rear lid – upper section Rear lid – lower sectionS492_01111 BodyBody stiffnessThe body structure of the new Jetta 2011 EU meets higher expectations in terms of acoustic and vibration behaviour thanks to the particularly stiff body configuration. This has been achieved with● ●Specific structural design of the nodes and force transmission points Optimum use of available construction space by employing three-part structure throughout – the passenger compartment is thus enclosed by computer-optimised body profiles.The Jetta 2011 EU Static torsional rigidity (Nm/°)CompetitorsS492_012Torsional frequency (Hz)The body structure of the Jetta 2011 EU is characterised by outstanding static torsional rigidity. The same applies to the dynamic rigidity. The Jetta 2011 EU therefore clearly stands out from its competitors. The high level of body rigidity benefits in particular the acoustics, the vibration characteristics and the excellent ride comfort of the new Jetta.12 Crash-safe body designOne major focus of development was that a high level of crash safety is also ensured in the measures to increase body stiffness. Therefore, in conjunction with the lightweight construction measures, a special combination of materials with varying degrees of deformability is specifically used for respective sections of the body. Specially adapted paths of force transmission and energy-absorbing deformation zones were created during the design of the body. This guarantees that the transmission of force in a crash follows a defined pattern. The body structure has been designed so that it ensures optimised transmission of force in frontal collisions as well as in side and rear collisions.The two illustrations show transmission of force using a frontal collision as an example.S492_014S492_01513 BodyBody featuresThe body of the Jetta 2011 EU has completely new exterior contours and thus meets the market-specific requirements very well.Front seatsThe front seats with manual adjustment now have a locking device for setting the backrest inclination. Depending on the equipment options, a manually adjusted 2-way lumbar support or an electrically adjusted 4-way lumbar support can be fitted. Electrically adjusted seats are optionally available for the Sportline version.BonnetThe Bowden cable for opening the bonnet is routed out of reach in the engine compartment.Space conceptThe larger vehicle interior gives you a completely new feeling of space. This has been made possible by making the vehicle longer, increasing the wheelbase and making the interior wider. The lowered beltline also gives a greater feeling of space in the back. The luggage compartment is generous. The load sill has been lowered and the opening made wider.HeadlightsThe headlights on the Jetta 2011 EU feature clear glass technology. The daytime running lights and turn indicators have been placed below the dipped beam and main beam lights as before.DoorsThe doors on the Jetta 2011 EU have a conventional design. Side impact bars are installed in all doors.RoofDepending on the equipment, a sliding/tilting sunroof and, at the rear, the roof aerial with the telephone aerial (GSM), the auxiliary heater aerial and the navigation system aerial (GPS) are fitted in the roof.14 Rear seat benchThe folding rear seat backrest is split 60:40. The rear backrests are both released with buttons in the luggage compartment.Button for unlocking the rear seat backrestRear windowThe aerials for radio reception are integrated in the rear window in addition to the window heating.S492_023Rear lidThe rear lid is opened from the outside with a microswitch in the rear lid handle. The rear lid lock is equipped with an emergency release. This consists of a swivel plate that has to be rotated from inside the luggage compartment to open the lid.Rear lidS492_024Tension spring Gooseneck hingeS492_022Rear lightsThe rear lights on the Jetta 2011 EU are split into two parts.The rear lid uses a completely new hinge system with a new gooseneck hinge and side tension springs. This allows the rear lid to automatically open fully while requiring considerably less force to close.15 Occupant ProtectionSafety equipmentThe Jetta 2011 EU essentially has the following safety equipment:● ● ● ● ●Driver airbag Front passenger airbag Side airbags at front Head airbags for front and rear occupants Belt tensioners and belt force limiters on the front seats●The seat occupied recognition system is the same as that used in the new Passat and Sharan.●Optimised sensor system for crash recognition (evaluation of structure-borne sound in crashes)●There are sensors in the front doors and in the vicinity of the C-pillar for detecting side collisions.16 ●Top Tether The Jetta 2011 EU is equipped with the Top Tether system. The Top Tether system serves to secure a child seat more firmly. In this case, an additional upper belt on the child seat is attached to corresponding anchors on the luggage compartment cover.Cover with Top Tether symbolTop Tether anchoring pointS492_025●The outer rear seats are equipped with Isofix anchoring points.S492_02617 Occupant ProtectionOptimised sensor system for crash recognitionThe crash sensors need to respond within a few milliseconds in severe frontal collisions so that the airbag control unit can immediately initiate deployment of restraint systems. This rapid procedure is absolutely necessary so that the airbags can inflate completely and thus protect the occupants in an optimum way. On the other hand, in less serious accidents, for example, car park bumps, airbag deployment is avoided as airbag protection is not needed in this case. This helps prevent unnecessary repair costs. The latest sensor systems for crash detection measure the deceleration of the vehicle and then determine whether the airbags or belt tensioners should be deployed. The Jetta 2011 EU now uses a new innovative sensor system for crash recognition.Airbag control unit J234Structure-borne sound18 How does the new sensor system for crash recognition work?As more extensive electronic functions become available through technical progress, an increasing number of new more refined evaluation processes are becoming possible. This is also true of the crash sensors and their evaluation. Function procedures●●●The airbag control unit J234 located centrally in the vehicle interior evaluates the low-frequency palpable deceleration signals using the crash sensors integrated into the control unit. In addition, specially adapted, highly integrated acceleration sensors measure the frequency components in the medium “audible” frequency range up to 20kHz. These signal components are formed from structure-borne sound during the fast deformation of supporting structures in the front end of the vehicle. They spread through the body structure at high speed and very quickly provide precise information about the severity of the crash. The crash characteristics can be determined more quickly by intelligently linking the palpable and audible signal components within the crash algorithm.S492_107This highly sensitive sensor system for crash recognition allows the deployment of airbags and belt tensioners to be adjusted better to the actual crash situation and the vehicle occupants to be given optimum protection in crashes.19 EnginesEngine/gearbox combinationsPetrol engine 6-speed manual gearbox MQ200-6F 0AJ 7-speed dual clutch gearbox DQ200-7F 0AMDiesel engine1.2 l 77 kW TSI turbocharged engine1.4 l 90 kW TSI turbocharged engine1.4 l 118 kW TSI engine with dual-charging2.0 l 147 kW TFSI engine1.6 l 77 kW CR TDI engine2.0 l-103 kW CR TDI engine20 5-speed manual gearbox MQ250-5F 0A46-speed manual gearbox MQ250-6F 02S6-speed dual clutch gearbox DQ250-6F DSG 02E6-speed manual gearbox MQ350-6F 02Q21 Engines1.2 l 77 kW TSI turbocharged engineThis engine continues Volkswagen’s downsizing strategy.Technical features●●●●●●●Diecast aluminium cylinder block with new grey cast iron cylinder liners Steel crankshaft with connecting rod and main bearing diameter reduced to 42 mm Low-friction lightweight pistons with ring set with reduced tangential forces Oil system with reduced oil throughput and oil pump with optimised efficiency Turbocharger with electrically operated waste gate Lightweight timing case with plastic and magnesium covers for ease of service Crankcase breather and ventilation system with oil separation facility integrated into cylinder block and cylinder headS492_016You will find further information on this engine in self-study programme no. 443 “The 1.2 l 77 kW TSI Engine with Turbocharger”.Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel Exhaust gas treatment CBZB 4-cylinder in-line engine 1,197 cm3 71 mmTorque and output diagram2 10 : 1 77 kW at 5,000 rpm 175 Nm at 1,550 to 4,100 rpm Simos 10 Super unleaded RON 95 Three-way catalytic converter with upstream broadband Lambda probe and downstream step-type Lambda probe EU5Engine speed (rpm) S492_017Emissions standard22Output (kW)75.6 mm Torque (Nm) 1.4 l 90 kW TSI turbocharged engineThis engine has already been used in other vehicle models.Technical features● ● ● ● ● ●● ● ● ●Homogeneous mode (Lambda 1) Stratified high-pressure start Turbocharger with waste gate Dual-circuit cooling system Air-to-liquid charge-air cooling Intake manifold with water-cooled charge air cooler Regulated duo-centric oil pump Metal cartridge oil filter Demand-regulated fuel system High-pressure fuel pump with integrated pressure limiting valveS492_018You will find further information on this engine in self-study programme no. 405 “The 1.4 l 90 kW TSI Engine with Turbocharger”.Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel Exhaust gas treatment CAXA 4-cylinder in-line engine 1,390 cm3 76.5 mmTorque and output diagram4 10 : 1 90 kW at 5,000 to 5,500 rpm 200 Nm at 1,500 to 4,000 rpm Bosch Motronic MED 17.5.5 Super unleaded RON 95 Three-way catalytic converter with upstream broadband Lambda probe and downstream step-type Lambda probe EU5Engine speed (rpm) S492_019Emissions standardOutput (kW)75.6 mm Torque (Nm)23 Engines1.4 l 118 kW TSI engine with dual-chargingThis engine has been carried over from the Scirocco without modifications.Technical features● ● ● ● ● ● ● ●● ●Homogeneous mode (Lambda 1) Stratified high-pressure start Turbocharger with waste gate Selectable mechanical supercharger Charge-air cooler Dual-circuit cooling system Demand-regulated fuel system High-pressure fuel pump with integrated pressure limiting valve Regulated duo-centric oil pump Metal cartridge oil filterS492_020You will find further information on this engine in self-study programme no. 359 “1.4 l TSI Engine with Dual-charging”.Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel Exhaust gas treatment CAVD 4-cylinder in-line engine 1,390 cm3 76.5 mmTorque and output diagram4 10 : 1 118 kW at 5,800 rpm 240 Nm at 1,500 to 4,500 rpm Bosch Motronic MED 17.5.5 Super unleaded RON 95 Three-way catalytic converter with upstream broadband Lambda probe and downstream step-type Lambda probe EU5Engine speed (rpm) S492_021Emissions standard24Output (kW)75.6 mm Torque (Nm) 2.0 l 147 kW TSI engineThe 2.0 l TSI engine is part of the EA888 in-line fourcylinder engine range. It is almost identical to the 1.8 l TSI engine.Technical features●●● ● ●The larger displacement has been achieved with modified pistons, connecting rods and crankshaft. The turbocharger pressure canister can be exchanged. Volumetric flow-controlled external gear oil pump Two balancer shafts Friction-optimised piston rings and cylinder honingS492_051You will find further information on this engine in self-study programme no. 401 “1.8 l TFSI 16v 118 kW engine”.Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel Exhaust gas treatment CCZA 4-cylinder in-line engine 1,984 cm3 82.5 mmTorque and output diagram4 9.6 : 1 147 kW at 5,100 to 6,000 rpm 280 Nm at 1,700 to 5,000 rpm Bosch Motronic MED 17.5.2 Super unleaded RON 95 Broadband lambda probe upstream of starter catalytic converter close to engine, steptype Lambda probe downstream of main catalytic converter EU5Engine speed (rpm) S492_053Emissions standardOutput (kW)92.8 mm Torque (Nm)25 Engines1.6 l 77 kW CR TDI engineThe 1.6 l TDI engine with common rail injection system and 4-valve technology is based on the 2.0 l 103 kW TDI engine with common rail injection system.Technical features●● ●●●Common rail injection system with piezo injectors, maximum injection pressure of 1,600 bar Adjustable turbocharger Exhaust gas recirculation module comprising exhaust gas recirculation system with exhaust gas recirculation valve and exhaust gas recirculation cooler Diesel particulate filter with oxidation catalytic converter Plastic intake manifoldS492_052You will find further information on this engine in self-study programme no. 442 “1.6 ltr. TDI engine with common rail injection system”.Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel Exhaust gas treatment CAYC 4-cylinder in-line engine 1,598 cm3 79.5 mmTorque and output diagram4 16.5 : 1 77 kW at 4,400 rpm 250 Nm at 1,500 to 2,500 rpm Simos PCR2 Diesel complying with DIN EN590 Exhaust gas recirculation, oxidation catalytic converter and diesel particulate filter EU5Engine speed (rpm) S492_054Emissions standard26Output (kW)80.5 mm Torque (Nm) 2.0 l 103 kW CR TDI engine2.0 l CR TDI engines from the second generation are being used in the Jetta 2011 EU. They are a further development of the first generation. Technical features●●● ● ● ● ● ●Common rail injection system with solenoidoperated injectors, maximum injection pressure of 1,800 bar Diesel particulate filter with upstream oxidation catalytic converter Plastic intake manifold with swirl flap adjustment Throttle valve module with plastic throttle valve Electric exhaust gas recirculation valve Adjustable turbocharger with travel feedback Low-temperature exhaust gas recirculation cooling Balancer shaft moduleS492_085You will find further information on this engine in self-study programme no. 403 “The 2.0 ltr. TDI Engine with Common Rail Injection System”.Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management CBAB 4-cylinder in-line engine 1,968 cm3 81 mmTorque and output diagram4 16.0 : 1 103 kW at 4,200 rpm 320 Nm at 1,750 to 2,500 rpm Bosch EDC 17 (common rail fuel injection system) Diesel complying with DIN EN590 Exhaust gas recirculation, oxidation catalytic converter and diesel particulate filter EU5Fuel Exhaust gas treatmentEngine speed (rpm) S492_055Emissions standardOutput (kW)95.5 mm Torque (Nm)27 TransmissionManual gearboxes – overviewManual gearbox Technical features See also …5-speed manual 0A4 • Developed from 02J gearbox • Gearshift mechanism optimised, final drive reinforced, case adapted • Without speedometer sender • CO2- and performance-optimised ratios • Gearbox version for start/stop system • Torque capacity up to 250 NmSelf-study programme 3066-speed manual gearbox 0AJ • Developed from 0AG gearbox • Adapted for the 1.4 l 90 kW TSI engine, distance between output shaft and differential increased, sheet metal bearing mounting replaced by cast bearing mounting for higher torques, toothing ground • Reinforced final drive • Without speedometer sender • CO2- and performance-optimised ratios • Gearbox version for start/stop system • Torque capacity up to 200 NmSelf-study programme 3066-speed manual gearbox 02S • Developed from 0A4 gearbox • Longer shafts with additional bearings, additional gear pair, new longer aluminium housing cover • CO2- and performance-optimised ratios • Gearbox version for start/stop system • Torque capacity up to 250 NmSelf-study programme 3066-speed manual gearbox 02Q • Developed from 02M gearbox • Changes to selector shaft, selector forks with stops in housing, modified bearings • Without speedometer sender • CO2- and performance-optimised ratios • Gearbox version for start/stop system • Torque capacity up to 350 NmSelf-study programme 30628 Dual clutch gearbox – overviewDual clutch gearbox Technical features See also …6-speed dual clutch gearbox 02E The 6-speed dual clutch gearbox 02E is equipped with a hydraulic dual clutch. It combines the advantages of a manual gearbox, such as high efficiency, robustness and sportiness, with the advantages of an automatic gearbox, i.e. high level of user-friendliness and easy gear changes.Self-study programme 3087-speed dual clutch gearbox 0AM The 7-speed dual clutch gearbox 0AM has been developed from the 6-speed dual clutch gearbox 02E. In contrast to the 02E gearbox, it works with a dry dual clutch and with separate oil circuits for gearbox and mechatronics. Also in contrast to the 02E gearbox, electric oil pump for the hydraulics is only activated on demand by the control unit. It is activated when the hydraulic pressure in the mechatronics falls below a certain value and the pressure needs to be raised again to guarantee correct functioning of the mechatronics.Self-study programme 39029 Running GearRunning gearThe running gear of the Jetta 2011 EU, which uses the same concept as the Jetta 2006, has been optimised and provides a high level of comfort and good dynamics. The wheelbase has been increased 73 mm compared with the Jetta 2006. This results from the front axle being moved 13 mm towards the front and the rear axle being moved 60 mm towards the rear. The rear track width has been increased by 30 mm.●Electronic stabilisation programme based on the MK60 system from Continental Teves●Electromechanical power steering●Modern McPherson strut front suspension●Brake servo with dual-rate characteristic curve30 ●Tyre pressure monitor (optional)S492_031●Four-link rear axle with very good vehicle dynamics and comfort characteristics●Brake assist system●Floor-mounted accelerator pedal with contactfree senders for accelerator pedal position31 Running GearFront axleThe front axle of the Jetta 2011 EU uses the same design as the front axle on the Golf 2009. A few details have, however, been developed further and adapted. The technical features are:● ● ●Assembly carrier (subframe) made from steel sheet Single-shell transverse links made from steel sheet Transverse link – rear bonded rubber bush with vertical axisLeft-hand transverse link (example) Rear bonded rubber bush (vertical axis)Coupling rod S492_032Anti-roll barRight-hand transverse linkAssembly carrier (subframe)Gearbox pendulum support Left-hand transverse linkS492_03332 Rear axleThe Jetta 2011 EU uses the four-link suspension as used in the Golf 2009 for the rear axle. Its design has been adapted due to the track width being increased by 30 mm.The technical features are:●The rear axle has a compact four-link design. The axle consists of three transverse links on each side of the vehicle (lower transverse link, track rod and upper transverse link) and the trailing arm.●●●The subframe is a welded component made from steel, which is bolted rigidly to the body. The hub carrier has been adapted for the increased track width. It is a cast steel part with moulded stub axle for carrying the wheel bearing.Thanks to this four-link axle design, longitudinal and lateral forces are decoupled almost completely and a high level of driving stability and comfort is thus achieved.Upper transverse linkMounting bracketAnti-roll barSubframeS492_034 Track rod Trailing arm Lower transverse link Hub carrier33 Running GearElectromechanical power steeringThe Jetta 2011 EU features the electromechanical power steering system used in the Golf 2009 as standard. It is a third generation electromechanical power steering system with double pinion from ZF.Input shaftElectromechanical power steering motor V187 with sender magnet for rotor position sensorIntegrated index sensorPower steering control unit J500 with sensor element for rotor position sensor S492_037The external steering angle sender G85 has been omitted on this steering system. Within the electromechanical power steering system, the sensor information is composed of the individual signals● ●from the integrated index sensor and from the rotor position sensor. (The sender magnet for the sensor is located on the motor shaft of the electromechanical power steering motor V187 and the sensor element is located in the power steering control unit J500.)The steering angle of the vehicle is calculated from all of this information in the power steering control unit J500. The calculated steering angle is used for the internal steering functions and is also supplied to other control units as a substitute for the G85 value.34 BrakesThe Jetta 2011 EU comes with the ESP electronic stabilisation programme as standard. A 10" brake servo is used for the engine versions described in this self-study programme.ESP unitBrake servoESP systemThe MK60 EC ESP unit is already used in the Golf 2009. It is produced by Continental Teves. In this system, the yaw rate sensor and the longitudinal and lateral acceleration sensors are integrated onto the ABS control unit J104 circuit board. The previous separate sensor cluster is not required.Hydraulic unitControl unitS492_038Functions●Circuit board in ABS control unit J104 Longitudinal acceleration sensor● ● ● ●Anti-lock brake system (ABS) with electronic brake pressure distribution (EBD) Traction control (TCS) Electronic stabilisation programme (ESP) Electronic differential lock (EDL) Brake assist systemLateral acceleration sensor Yaw rate sensorDirection of travelThe electronic stabilisation programme is constantly activated.ABS control unit J104 Hydraulic unitS492_04135 Running GearTyre pressure monitor (TPM)The TPM tyre pressure monitor is a software module in the ABS control unit, which evaluates the data from the ABS wheel speed sensors to monitor the tyre pressures. A new tyre pressure monitor, which has been expanded compared with the previous version, is being used in the Jetta 2011 EU for specific markets.You can find out about the TPM tyre pressure monitor in self-study programme no. 347 “Tyre Pressure Monitoring Systems”.FunctionThe rolling radius of a wheel decreases as the tyre inflation pressure falls and the wheel rotates faster at the same vehicle speed. The wheel speed sensors calculate the speed difference, which is then evaluated in the ABS control unit J104. A warning lamp in the dash panel insert and an acoustic signal informs the driver and asks him to check the tyre pressure. The resonant frequency of the tyres is measured in addition to the speed. This produces a more precise evaluation of the pressure loss. The tyre pressure monitor is capable of recognising creeping pressure loss at several wheels at the same time. Since the characteristics of each individual tyre are different, calibration is necessary to determine the reference data for the currently fitted tyres and the pressures currently stored in the system. The system also needs to be re-calibrated after the tyre pressure is changed at one or more wheels.S492_043Control unit in dash panel insert ABS control unit with integrated software for tyre pressure monitor (TPM) Button for tyre pressure monitorThe same applies if a wheel is changed. Then the inflation pressure needs to be set to the required level and the system should be re-calibrated for this pressure. Snow chain recognition The system is not active if snow chains are detected.36 CalibrationWith the ignition switched on, press the tyre pressure monitor button until you hear a confirmation tone. The tyre pressure values recorded during calibration are now stored in the tyre pressure monitoring system as required tyre pressures. The tyre pressure monitor button is located at the top left of the glove compartment.During calibration make sure that the tyre pressure prescribed for the vehicle is set at the respective tyre.S492_044Display – warningIf the pressure falls by a certain value below the required tyre pressure stored during calibration, the driver will receive a warning from the system. The warning is signalled by a gong and the yellow warning lamp for the tyre pressure monitor in the dash panel insert. The lamp remains lit until the system is recalibrated. The gong will sound each time the vehicle is started until recalibration is performed.S492_045When a vehicle is serviced, service staff must inform the driver that he himself is responsible for setting the correct tyre pressure. The tyre pressure monitor is an information system that provides a message if pressure is lost at one tyre. It does not, however, relieve the driver of his responsibility to check the tyre pressures on a regular basis.37 Electrical SystemVehicle electrical systemLocations of electrical componentsIn the Jetta 2011 EU, the locations of important electric components have changed compared with the previous model. The illustration shows the locations of these components.Plastic caseOnboard supply control unit on the back of a plastic caseElectronics box on left of engine compartment next to the batteryRelay carrier on front of plastic case – at topFuse holder on front of plastic case – at bottom38 Electrical system architectureThe electrical system is the same as the Golf 2009 electrical system except for vehicle model and platform-specific adaptations.Onboard supply control unitThe control unit from the Golf 2009 is used as the onboard supply control unit.Onboard supply control unit J519 with 3 socketsS492_035The onboard supply control unit also includes the functions of the convenience system central control unit J393. It is located under the dash panel on the left on the back of a plastic case, which holds fuses and relays on its front. It is connected via three connectors.S492_07239 Electrical SystemOnboard supply control unit functionsOnboard supply control unit – functionsLoad managementPowertrain, convenience and diagnosis CAN data buses Roof LIN data bus (sliding/tilting sunroof)Activation of the fuel supply system of the electrical fuel pump Light controlRelease and control of sliding/tilting sunroofReversing lightActivation of rear lid releaseDetecting the externally dimmed interior light – information is placed on the CAN data bus Fog lightsStarter repeat inhibitorHorn activationActivation of daytime running lights via separate daytime running light bulbs Activation of brake light including emergency braking lights, turn signal, hazard warning lights Activation of side and parking lights (parking lights only available when ignition switched off) Activation of static cornering lights (via fog lights)Heated rear window activationDoor control unit activationRemote control (433 MHz) – aerial integrated into onboard supply control unit Convenience closeActivation of front wipers level I/II and interval, not via LIN but conventionally Enabling of seat heatingFunction block for “Keyless Access” locking and start system PersonalisationInterlockAnti-theft alarm system40 “Keyless Access” locking and starting systemThe Jetta 2011 EU can be equipped with the “Keyless Access” locking and starting system in specific markets. This system allows you to unlock or lock the vehicle without actively using the vehicle key and to start and switch off the engine with a button.System architectureThe “Keyless Access” locking and starting system is an optional extra for the Jetta 2011 EU. The diagram compares the system architecture with and without “Keyless Access” system.System architecture without “Keyless Access”System architecture with “Keyless Access”Key with remote controlKey with “Keyless Access” and remote controlWireless 433MHzWireless 433MHzWireless 125kHz“Keyless Access” – transmission aerials (doors, interior, luggage compartment)Ignition lock“Keyless Access” – control unit“Keyless Access” – door handles (front) with proximity sensorElectronic steering column lockButton for starting systemOnboard supply control unitOnboard supply control unitElectrical system (rest of vehicle)Electrical system (rest of vehicle)Green = identical interfaces and control unitsS492_047Mechanical interfacesOne component of the “Keyless Access” locking and starting system that should be highlighted is the electronic steering column lock (ESL) that replaces the mechanical steering lock.41 Electrical SystemElectrical interfacesThe onboard supply control unit includes – as on a basic model without “Keyless Access” locking and start system – – the electronic module with high-frequency receiver (wireless receiver) for the central locking system. The onboard supply control unit is integrated into the CAN data bus via which various coordination processes occur, information is exchanged etc. within the system. Additional components are the electronic steering column lock (ESL) with its own control unit and the entry and start authorisation control unit J518 (“Keyless Access”) including aerials, door handles and the vehicle key (ID sender).Driver interfacesThe “Keyless Access” locking and starting system takes care of recognition and identification of the key both outside and inside the vehicle. The aerials fitted in the front door handles and in the vehicle interior are used to set up the connection between the vehicle key and the “Keyless Access” system. The following functions are available after successful identification:●●●Keyless Entry – Unlock vehicle via driver or front passenger door handle – take hold of handle [A]. The ID sender must be located within the exterior monitoring area on the corresponding side of the vehicle or at the rear of vehicle. Keyless Go – Start the engine and drive – a valid ID sender must be located inside the vehicle. If you want to start the vehicle, press the starter button and the clutch (if vehicle has a manual gearbox) or the brake (if vehicle has an automatic gearbox). Keyless Exit – Lock vehicle upon leaving the vehicle – driver door must be closed. Press the outer button on the handle of the driver or front passenger door [B]. If the vehicle is locked via the front passenger door, it must be closed. The ID sender must be located within the exterior monitoring area on the corresponding side of the vehicle or at the rear of vehicle.Monitoring area of Jetta with “Keyless Access”●Exterior area (monitoring area) – The driver accesses the vehicle without using a key via the “Keyless Access” door handle (driver and front passenger side). Capacitive sensors fitted inside the door handles are used to detect the unlock request. The ID sender is searched for within the corresponding exterior area via the “Keyless Access” transmitter aerials.S492_062S492_061●Interior area – The driver can start and switch off the vehicle if the ID sender is present in the interior via the single-step starter button (located in the row of buttons in front of the selector lever).Interior of Jetta with vehicle keyS492_064S492_06342 System overviewS492_048Legend 1 2 3 Starter button E378 Onboard supply control unit J519 Electronic steering column lock control unit J764 incl. transponder coil for emergency start (electronic steering column lock) Entry and start authorisation control unit J518 Driver door exterior handle contact sensor G415 and driver side aerial for entry and start authorisation R134 Front passenger door exterior handle contact sensor G416 and front passenger side aerial for entry and start authorisation R135 7 8 9 10 11 Interior aerial 1 for entry and start authorisation R138 Interior aerial 2 for entry and start authorisation R139 Luggage compartment aerial for entry and start authorisation R137 Rear bumper aerial for entry and start authorisation R136 Vehicle key (ID sender)4 56The owner’s manual provides detailed information on operation of the “Keyless Access” locking and starting system.43 Electrical SystemLightsThe lights on the Jetta 2011 EU have been adapted to the current Volkswagen design style in terms of exterior design and also internal structure.Main beam (H7, 55W) Side light (W, 5W) Dipped beam (H7, 55W)Front lightsThe Jetta 2011 EU has double-reflector headlights with turn signal, side lights, main beam, dipped beam and daytime running lights. The fog lights are optionally integrated into the static cornering light function. Replacing bulbs has been simplified with the familiar “one-touch system”. A headlight cleaning system can be added as an optional extra.S492_090 Turn signal (PY, 21W) Fog light (H11, 51W) Daytime running light (P, 21W)Daytime running lightsThe daytime running light bulb lights up when the daytime running lights are switched on.S492_094Side lightsThe side light bulb lights up when the side lights are switched on.S492_095Dipped beamThe dipped beam bulb and the side light bulb light up when dipped beam is switched on.S492_096Main beamThe main beam bulb, the dipped beam bulb and the side light bulb light up when the main beam is switched on.S492_09744 Rear lightsThe rear lights on the Jetta 2011 EU are split into two sections.Left turn signal (P, 21W)Rear fog light (P, 21W – only left)Right turn signal (P, 21W)S492_092Brake/ tail light (P, 21/5W)Tail light (R, 5W)Reversing light (P, 21W)Reversing light (P, 21W)Tail light (R, 5W)Brake/ tail light (P, 21/5W)The brake/tail light and turn signal are integrated into the section of the rear light on the left-hand and right-hand body side panel. One bulb is used for the brake/tail light. The left- and right-hand sections of the rear light in the rear lid both contain the tail light and reversing light. The rear fog light is only in the left-hand rear light section.Night-time designThe rear lights on the Jetta 2011 EU have a striking night-time design and thus contribute greatly to fast and clear recognition of typical Volkswagen design features.S492_09345 Electrical SystemStart/stop systemThe start/stop system, which was used for the first time at the start of the eighties in the Passat Formel E as well as in the Golf Ecomatic (1993) and in the Lupo 3L (1999), is now being used in all vehicle classes at Volkswagen in the form of an updated generation. The proven start/stop system will therefore also be available as an optional extra for the Jetta 2011 EU. The basic advantages of the system are the following:● ●●The engine does not run at idle unnecessarily. The fuel consumption and the harmful emissions are reduced in city traffic and in stop-and-go traffic. The noise emissions are reduced to zero when the vehicle is stationary.Function overviewThe start/stop system works in a very simple way – also in terms of customer friendliness.●● ●If you shift into neutral while the vehicle is stationary and release the clutch pedal, the engine will switch off automatically. When you want to continue driving, you just have to press the clutch pedal to start the engine. You can quickly continue the journey after selecting a gear.S492_113The function overview shows how the start/stop system works using a manual gearbox as an example.46 Regenerative brakingThe start/stop system has been combined with the “regenerative braking” function from the BlueMotion Technology package to make it even more efficient. The regenerative braking function supports an efficient supply of electrical energy to the vehicle electrical system.What does regenerative braking mean?Regenerative braking refers in general to the recovery of energy during braking. This recovered energy is supplied to the battery to charge it. Regenerative braking is controlled by a system of control units and sensors, among which the engine control unit J623 and the data bus diagnostic interface J533 perform the main tasks.Engine control unit J623 BatteryAlternatorS492_108Function procedure●The alternator voltage is raised during deceleration or braking phases. This leads to increased charging of the battery. The deceleration of the vehicle is supported.●However, in acceleration phases, the alternator load is reduced, which relieves the burden on the engine and consequently also reduces fuel consumption.You will find further information on the start/stop system and also regenerative braking in self-study programme no. 426 “Start/Stop System 2009”.47 Electrical SystemOverrunDuring overrun – when braking – the kinetic energy of the vehicle is used in an optimum way to charge the battery. For this purpose, the alternator is controlled so that it produces a high charging voltage.Brake energy recovery during overrunS492_109 Charging batteryAccelerationOn the other hand, low voltage is set at the alternator during acceleration. The engine load is reduced because it does not need to use as much power to drive the alternator. During this phase, the battery also supplies the vehicle electrical systemRelieving the alternator during acceleration phasesS492_11048 Optical parking systemThe optical parking system (OPS) in the Jetta 2011 EU is based on the system used in the Golf 2009 with details adapted to the Jetta. The system is a software extension for the parking aid. The parking aid system uses ultrasound sensors in the bumpers and an acoustic warning to help the driver judge the distance from other parked cars or obstacles. Only the warning from the sensor closest to the obstacle is supplied. The parking distance warning system is switched on and off by pressing the corresponding button – parking aid button E266 – in the row of buttons in the centre console. The optical parking system does not only generally detect obstacles in front of or behind the vehicle, but also their position in the scanning area. Compared with the parking aid, the driver is supported not just acoustically but also visually. The optical parking system is activated simultaneously with the parking aid. The parking aid control unit J446 processes the distance information according to sector and transfers it to the display unit (radio or radio/navigation unit). The operating and display protocol (BAP) is used for this.S492_120 Parking aid button E226You will find more information on the optical parking system in self-study programme no. 417 “The Passat CC 2009”.FunctionDuring the parking manoeuvre, the radio/navigation unit screen shows a diagram of the vehicle that is surrounded by areas which are black or highlighted in colour. These areas show the driver the exact position of the vehicle and the distance from obstacles.Display of OPS picture on RCD 310S492_116Display of OPS picture on RCD 510 and RNS 310/510Advantages of optical parking system●●●The position of the obstacles is shown in relation to the position of the vehicle. You can manoeuvre the car using the display on the screen. Fast and simple assessment of the current state on the display.S492_11749 Electrical SystemNetworking conceptOverview of networked electronic control unitsThe control units are networked via various data bus systems to allow them to exchange data. The data bus diagnostic interface J533 (gateway) is an independent control unit that acts as the interface for the following data bus systems:● ● ● ● ● ●Powertrain CAN data bus Convenience CAN data bus Infotainment CAN data bus Instrument cluster CAN data bus Diagnosis CAN data bus LIN data busControl units connected to Powertrain CAN data bus Convenience CAN data bus Sensor CAN data bus Cornering light CAN data bus Infotainment CAN data bus LIN data bus CAN data bus wire LIN data bus wire K-wire a – Instrument cluster CAN data bus b – Diagnosis CAN data bus50 Legend C** Alternator D Ignition/starter switch E221 Operating unit in steering wheel (multifunction steering wheel) E313 Selector lever G85 Steering angle sender G273 Interior monitoring sensor G295 NOx sender G384 Vehicle inclination sender G397 Rain and light sensor H8 Anti-theft alarm system horn J104 ABS control unit J234 Airbag control unit J245 Sliding sunroof adjustment control unit J255 Climatronic control unit J285 Control unit in dash panel insert J345 Trailer detector control unit J362 Immobiliser control unit J367** Battery monitor control unit J386 Driver door control unit J387 Front passenger door control unit J388 Rear left door control unit J389 Rear right door control unit J446 Parking aid control unit J500 Power steering control unit J503 Control unit with display for radio and navigation J518 Entry and start authorisation control unit J519 Onboard supply control unit J527 Steering column electronics control unit J533 Data bus diagnostic interface J608 Special vehicle control unit J623 Engine control unit J667 Output module for left headlight J668 Output module for right headlight J743* Mechatronic unit for dual clutch gearbox J745 Control unit for cornering light and headlight range control J764 Electronic steering column lock control unit J844 Main beam assist control unit R Radio R36 Telephone transmitter and receiver unit R215 Interface for external multimedia unit T16 Diagnosis connector Z Auxiliary heaterS492_046* With dual clutch gearbox only ** For vehicles with start/stop system51 Heating and Air ConditioningAir conditioningTwo different types of air-conditioning system are used in the Jetta 2011 EU.Vent for windscreenVent in the dash panel centre – rightVent in the dash panel right Vent for front right footwell Vent for rear right footwellVent in centre of dash panel – leftVent in the dash panel leftVent for front left footwell Vent for rear left footwellVent rear centre consoleS492_065Air-conditioning system● ●2-zone Climatronic●●●One climatic zone Manual adjustment of the blower level using a rotary switch Manual adjustment of the temperature via an electronic rotary temperature knob Manual adjustment of the air distribution via an electronic rotary knob●●Automatic air-conditioning system with two climatic zones Automatic control of the blower level and the flap position Automatic control of the vent and interior temperature52 Control panelsControl panel for air-conditioning systemAC button for air-conditioning function Button for heated rear window Button for air recirculation functionElectronic rotary knob for temperature Button for seat heating – driver S492_067 Rotary switch for blower levelElectronic rotary knob for air distribution Button for seat heating – front passengerControl panel for 2-zone ClimatronicAir distribution in footwell Air distribution from vents on dash panel Windscreen air distribution Defrost function for windscreen Electronic rotary knob for temperature on driver sideAC button for air-conditioning function Button for air recirculation function Button for heated rear window Electronic rotary knob for temperature on front passenger sideButton for seat heating – driver AUTO button with two blower modesS492_068Button for seat heating – front passengerBlower speed switch with feedback LEDsDUAL button When the DUAL button is activated, the Climatronic system works in two climatic zone mode and, when the DUAL button is deactivated, in single climatic zone mode.53 Radio, Telephone and NavigationRadios and radio/navigation systems in the Jetta 2011 EUThe RCD 210, RCD 310 and RCD 510 radio systems as well as the RNS 310 and RNS 510 radio/navigation systems are available for the Jetta 2011 EU.RCD 210 radioTechnical features– Monochrome display with a resolution of 122 x 36 pixels – FM, TP and RDS reception via a single tuner – TP button; stations that do not broadcast TP information will be displayed with “No TP” – AM reception – 24 memory slots for AM and FM stations each on two memory levels with 6 slots – The autostore function fills the current memory level with the six strongest stations – “Initial Autostore” fills all 24 memory levels with receivable FM and AM stations – Four loudspeakers with up to 20 Watt output can be connected at the front – Treble, bass and balance sound adjustments – Fader adjustment, only with four loudspeakers – Integrated CD drive – Brightness of display backlight can be controlled independently of the dim signal for the vehicle interior lighting – Service test modeS492_091Combination and expansion possibilities– Universal mobile phone preparation UMPP (mono playback only) – Compatible telephone hands-free systems from third-party manufacturers – Reduction of audio volume in vehicles with parking distance warning system – Can be operated via multifunction steering wheel and displayed in dash panel insert – Audio input interface (AUX-IN)The features may vary depending on the vehicle equipment.54 RCD 310 radioTechnical features– Monochrome display with a resolution of 302 x 45 pixels – FM twin-tuner for FM, TP and RDS reception with phase diversity – Integrated DAB tuner (digital radio); depending on equipment – Integrated CD drive – Media support for MP3 and WMA audio data (with ID3-Tag) – Optical parking system (OPS) – Air-conditioning system information – RDS FM/AM Europe radio – Eight loudspeakers with up to 20 Watt output can be connected – Speed-dependent volume control (GALA) – Self-diagnosis and loudspeaker diagnosis – TP button; stations that do not broadcast TP information will be displayed with “No TP” – BAP operating and display protocol – Audio input interface (AUX-IN)S492_070Combination and expansion possibilities– Universal mobile phone preparation UMPP – Reduction of audio volume in vehicles with parking distance warning system – Support of display on dash panel insert via the BAP operating and display protocol as well as the DDP display data protocol – Control via multifunction steering wheel (MFW) and multifunction display (MFD) – Media Device Interface (MDI)The features may vary depending on the vehicle equipment.55 Radio, Telephone and NavigationRCD 510 radioTechnical features– Touch-sensitive 6.5" TFT colour screen with a resolution of 400 x 240 pixels – FM twin-tuner for FM, TP and RDS reception with phase diversity – AM reception – Eight loudspeakers with up to 20 Watt output can be connected – Integrated 6-disc CD changer – Integrated memory for TIM information; depending on equipment – Integrated DAB tuner (digital radio); depending on equipment – Integrated SD memory card reader (SD=Secure Digital) – Media support for MP3 and WMA audio data – Audio input interface (AUX-IN) – Self-diagnosis and loudspeaker diagnosis – Display of climate control information (displayed temporarily) – Optical parking system (OPS)S492_071Combination and expansion possibilities– Reduction of audio volume in vehicles with parking distance warning system – Support of display on dash panel insert via the BAP operating and display protocol as well as the DDP display data protocol – Universal mobile phone preparation UMPP – Compatible, external telematics units – Control via multifunction steering wheel – Media Device Interface (MDI)The features may vary depending on the vehicle equipment.56 RNS 310 radio/navigation systemTechnical features– Touch-sensitive 5" TFT colour screen with a resolution of 400 x 240 pixels Operation via touch screen and rotary/ push knob – FM twin-tuner for FM, TP and RDS reception with phase diversity – Eight loudspeakers with up to 20 Watt output can be connected – Integrated CD drive for navigation, audio – Media support for MP3 and CD audio – Playback function with track display (MP3) – Integrated SD memory card reader – Map display from driver perspective (2.5D) – Navigation function with map, integrated direction symbols and speech – CD/SD navigation (country/major routes in Europe) – SD navigation without navigation CD inserted – Copying of navigation data from CD to SD – Linking several countries on one SD card – TMC function & TMC background reception (the current traffic messages are stored) – Display of vehicle functions (clock, climatic control, optical parking system) – Audio input interface (AUX-IN)S492_073Combination and expansion possibilities– Reduction of audio volume in vehicles with parking distance warning system – Controllable via multifunction steering wheel – Audio input interface (AUX-IN) on front of unit – Support of display on dash panel insert via the BAP operating and display protocol as well as the DDP display data protocol – Audio playback of external sources, e.g. CD players and iPods – Universal mobile phone preparation UMPP – Media Device Interface (MDI)The features may vary depending on the vehicle equipment.57 Radio, Telephone and NavigationRNS 510 radio/navigation systemTechnical features– Touch-sensitive 6.5" multi-colour display (MFD) with a resolution of 800 x 480 pixels – RDS, FM and AM Europe radio – FM twin-tuner for FM, TP and RDS reception with phase diversity – Eight loudspeakers with up to 20 Watt output can be connected – Integrated DVD drive for navigation, audio and video – Integrated drive hard for storing navigation and audio data – Integrated SD memory card reader – Media support for MP3 and WMA audio and video data – Map display in 2D, 3D bird’s eye view and topographical view – Navigation function with map, split screen and speech – TMC function (the current traffic messages are stored), dynamic navigation (Europe and North America) – Off-road functions – Display of climate control information (displayed temporarily) – Optical parking system (OPS) – Audio input interface (AUX-IN)S492_074Combination and expansion possibilities– Controllable via multifunction steering wheel – Reduction of audio volume in vehicles with parking distance warning system – Support of display on dash panel insert via the BAP operating and display protocol as well as the DDP display data protocol – Display of navigation symbols by the dash panel insert control unit (Highline) – Video playback of external sources, for example, DVD players – Audio playback of external sources like, e.g. CD players and iPods – Universal mobile phone preparation UMPP – Media Device Interface (MDI)The features may vary depending on the vehicle equipment.58 Media Device Interface boxThe Jetta 2011 EU can be optionally equipped with the media device interface box – MDI for short. The MDI allows you to connect mobile audio or multimedia devices to the infotainment system and to display, control and play back their audio content over the vehicle loudspeakers or on the infotainment monitors. The MDI control unit is located in a case on the left behind the rear wall of the glove compartment – below the switch for deactivating the front passenger airbag.Adapter connectionS492_075Adapter cableConnection possibilities with USB adapter cableS492_076 S492_077 Connection possibilities with adapter cable for Apple iPod/iPhoneS492_078 Connection possibilities with mini USB adapter cableConnection possibilitiesMobile devices are connected using special adapter cables, which are connected to the adapter connection that acts as a central interface. The following audio formats are currently supported and can be played back: MP3, AAC, WMA and OGG Vorbis.59 Radio, Telephone and NavigationAerial systemsOn the Jetta 2011 EU, several aerials – for AM, FM1, FM2 and digital radio reception (DAB) – are integrated into the rear window. The aerials for navigation (GPS) and telephone reception (GSM) are installed in the separate roof aerial. The FM impedance transformers are located in the centre of the C-pillars at the side of the rear window.Radio with single aerialAM/FM impedance converterS492_115Radio with diversity aerial, GSM and DABRoof aerial FM2 impedance transformer* AM/FM1 impedance transformer GSMS492_080* There are two versions (1 - FM2 or 2 - FM2/DAB)60 Radio/navigation system with diversity aerial, GSM, DAB and GPSRoof aerial GPS GSMFM2 impedance transformer*AM/FM1 impedance transformerS492_081* There are two versions (1 - FM2 or 2 - FM2/DAB)61 Radio, Telephone and NavigationMobile phone preparationTwo mobile phone preparations are used in the Jetta 2011 EU. Both systems are only shown briefly here – you can find more detailed information in self-study programme no. 423 “The Golf 2009”.Plus mobile phone preparation (BluetoothTM only) with audio streamingPure speech data via HFPTelephone holder Terminal 30 Terminal 31 For music data A2DPS492_114Legend E508 Operating unit for preparation for mobile telephone J503 Control unit with display for radio and navigation R Radio R36 Telephone transmitter and receiver unit R38 Telephone microphone R65 Telephone aerialCAN data bus Audio channels Analogue wire BluetoothTM62 Premium mobile phone preparation with Bluetooth TM (rSAP, HFP, A2DP)Mobile phone (rSAP, HFP, A2DP)AudioTerminal 30 Terminal 31S492_079Legend E221 Operating unit in steering wheel (multifunction steering wheel) E508 Operating unit for preparation for mobile telephone J285 Control unit in dash panel insert (instrument cluster) J503 Control unit with display for radio and navigation J527 Steering column electronics control unit J533 Data bus diagnostic interface R36 Telephone transmitter and receiver unit R38 Telephone microphone R65 Telephone aerialCAN data bus LIN data bus Analogue wire BluetoothTM63 492© VOLKSWAGEN AG, Wolfsburg All rights and rights to make technical alterations reserved. 000.2812.49.20 Technical status 03.2011 Volkswagen AG After Sales Qualifizierung Service Training VSQ-1 Brieffach 1995 D-38436 Wolfsburg❀ This paper was manufactured from pulp that was bleached without the use of chlorine.