TECHNICAL DOCUMENTATION
SSP 606 Audi 1,8l and 2,0l TFSI engines EA888

This PDF is currently unavailable.
Read document text
Self Study Programme 606 For internal use onlyAudi 1.8l and 2.0l TFSI engines of the EA888 model family (third generation)Audi Service TrainingThe launch of the 1.8l TFSI engine marks the third generation of the successul EA888 four-cylinder engine family from Audi. The motives for this development are the increasingly stringent exhaust emissions standards (EU 6) and, of course, the demands for better fuel economy and lower CO2 emissions. To achieve these goals, the engine has been completely revised. In addition to downsizing, downspeeding* is playing an increasingly important role. The "global engine" is built at Audi's Hungarian engine plant in Györ and in Silao (Mexico) as well as in the People's Republic of China. Here, the EA888 engine family is produced in Shanghai and Dalian, and will in future also be manufactured in Changchun. Like its predecessor, the engine is available in 1.8-litre and 2.0-litre variants. It is used for a variety of vehicle platforms and Group brands, and is available in a wide range of power ratings.The engineers in Ingolstadt placed special emphasis on the following priorities during the development cycle: • A high proportion of identical parts for all engine versions • Reducing engine weight • Minimising intra-engine friction • Increasing power output and torque in conjunction with good fuel economy • Improving comfort Another requirement is that the engines be suitable for use in all markets, including those where low grade fuel is prevalent. The "global engine" also has a key role to play against the background of increasing hybridisation. For a detailed technical description of the version 0 engine, refer to Self Study Programme 384 "Audi chain-driven 1.8l 4V TFSI engine". To find out more about the modifications incorporated into versions 1 and 2, refer to Self Study Programme 436 "Modifications to the chain-driven 4-cylinder TFSI engine".1.8l TFSI engineeMedia This SSP contains QR codes which you can use to access interactive media. Refer to "Information on QR codes" on page 63.606_001The following innovative, new technologies are featured: • Exhaust manifold integrated into the cylinder head • Dual injection system with direct and port injection • New, compact turbocharger module with cast steel turbine housing, electrical wastegate actuator and oxygen sensor upstream of the turbine • Innovative Thermal Management system with fully electronic coolant temperature controlLearning objectives of this Self Study Programme: This Self Study Programme introduces you to the technology in the 4-cylinder TFSI engines of the EA888 engine family (third generation). It mainly describes the technology of the 1.8l TFSI engine. When you have worked your way through this Self Study Programme, you will be able to answer the following questions: • What are the key technical modifications behind the development of the EA888 engine family? • How do the innovative, new technologies work? • What changes does the 1.8l TFSI engine bring for customer service?2ContentsIntroductionDevelopment goals __________________________________________________________________________________________________________________________________________ 4 Brief technical description __________________________________________________________________________________________________________________________________ 5 Technical features ____________________________________________________________________________________________________________________________________________ 6Engine mechanicalsOverview ______________________________________________________________________________________________________________________________________________________ 8 Engine block __________________________________________________________________________________________________________________________________________________ 8 Oil pan _________________________________________________________________________________________________________________________________________________________ 9 Crank train (1.8l TFSI engine) _ _____________________________________________________________________________________________________________________________ 10 Chain drive ___________________________________________________________________________________________________________________________________________________ 12 Balancer shafts ______________________________________________________________________________________________________________________________________________ 13 Auxiliaries mounting bracket ______________________________________________________________________________________________________________________________ 14 Cylinder head ________________________________________________________________________________________________________________________________________________ 15 Integral exhaust manifold _________________________________________________________________________________________________________________________________ 18 Positive crankcase ventilation _ ____________________________________________________________________________________________________________________________ 20Oil supplySystem overview ____________________________________________________________________________________________________________________________________________ 24 Oil supply ____________________________________________________________________________________________________________________________________________________ 26 Oil filler cap __________________________________________________________________________________________________________________________________________________ 28 Switchable piston cooling jets _____________________________________________________________________________________________________________________________ 28Cooling systemSystem overview ____________________________________________________________________________________________________________________________________________ 30 Innovative Thermal Management (ITM) __________________________________________________________________________________________________________________ 32Air supply and chargingSystem overview ____________________________________________________________________________________________________________________________________________ 40 Air routing system for transverse mounted engines ____________________________________________________________________________________________________ 41 Air routing system for longitudinal mounted engines __________________________________________________________________________________________________ 42 Intake manifold _____________________________________________________________________________________________________________________________________________ 43 Exhaust turbocharger _ ______________________________________________________________________________________________________________________________________ 44Fuel systemSystem overview ____________________________________________________________________________________________________________________________________________ 48 Mixture formation / dual injection system _______________________________________________________________________________________________________________ 49 Operating modes ____________________________________________________________________________________________________________________________________________ 50Engine management systemSystem overview – 1.8l TFSI engine CJEB (Audi A5 ’12) _ ________________________________________________________________________________________________ 52Differences between engine versionsDifferences between 1.8 l and 2.0 l engines, as well as longitudinal and transverse mounting _ ___________________________________________________ 54 Differences between components in longitudinal and transverse mounted engines ________________________________________________________________ 55 Differences between components in the engines with 1.8 l and 2.0 l displacement ________________________________________________________________ 56 Differences between the exhaust turbochargers ________________________________________________________________________________________________________ 58 Differences between combustion methods _ _____________________________________________________________________________________________________________ 59AnnexService _ _______________________________________________________________________________________________________________________________________________________ 60 Glossary ______________________________________________________________________________________________________________________________________________________ 62 Self Study Programmes ____________________________________________________________________________________________________________________________________ 63 Information on QR codes _ __________________________________________________________________________________________________________________________________ 63The Self Study Programme teaches a basic knowledge of the design and functions of new models, new automotive components or new technologies. It is not a Repair Manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. For further information about maintenance and repair work, always refer to the current technical literature. In the glossary at the end of this Self Study Programme you will find an explanation of all terms which are in italics or indicated by an asterisk.NoteReference3IntroductionDevelopment goalsTop of the agenda for the development of the third generation of the EA888 engine family was meeting the EU 6 exhaust emission limits and compatibility of the engine with the various modular platforms. The focus of development work on the base engine was on cutting engine weight while at the same time reducing friction.Adaptation to modular kitTo be able to use the third generation of the EA888 engine family as a "global engine" in the modular longitudinal kit (MLB) and the modular transverse kit (MQB), it was necessary to revise its dimensions, mounting and connecting points. Engine mounts and a dipstick are used if the engine is transverse mounted. If the engine is longitudinal mounted, use is made of engine supports and a sealing cap in place of a dipstick.CO2 reductionTo meet both the EU 6 emission limits while reducing CO2 emission, the following improvements and modifications have been made.Downsizing/downspeeding • Intake and exhaust camshaft adjusters • Audi valvelift system (AVS) Friction and weight reduction • Balancer shafts, in part roller bearing mounted • Smaller main bearing diameter • Lower oil level • Reduced tensioning force in auxiliary driveCylinder head • Cylinder head with Integrated Exhaust Manifold (IEM) • Weight-reduced exhaust turbocharger housing • Electrical wastegate actuator Injection • FSI and MPI injectors Thermal management • Rotary slide valve controlReducing frictionThe chain tensioners have been optimised for the reduced oil pressure. In addition to this, the tensioning force of the chains has been reduced, in turn reducing friction. Furthermore, the crankshafts are made with smaller main bearing diameters which produce less friction. The belt drive configuration is identical for longitudinal and transverse mounted engines. However, the alternators and A/C compressors are model-dependent.Reference For more detailed information on the design, function and versions of the 1.8l TFSI engine, refer to Self Study Programme 384 "Audi chain-driven 1.8l 4V TFSI engine" and Self Study Programme 436 "Modifications to chain-driven 4-cylinder TFSI engine".4Brief technical descriptionEngine type • • • • Four-cylinder in-line petrol engine with direct injection Exhaust turbocharging with charge air cooling Chain drive Balancer shaftsValve control • Four valves per cylinder, twin double overhead camshafts (DOHC) • Continuous intake and exhaust camshaft adjustment • Audi valvelift system (AVS) • Simos 12 engine management system (Continental) • Start-stop system and brake energy recuperation Mixture formation • • • • • Fully electronic engine management system with EPC Combined direct and port injection systems Adaptive lambda control Mapped ignition with static high voltage distribution Cylinder-selective adaptive knock control eMedia Animation showing the overall engine.606_0571.8l TFSI engine Torque-power curveEngine with engine code CJEB Power output in kW Torque in NmEngine speed [rpm]606_0085Technical features1.8l TFSI engineEngine code Installation position Displacement in cm3 Power output in kW at rpm Torque in Nm at rpm Bore in mm Stroke in mm Compression ratio Crankshaft Main crankshaft bearing diameter in mm Engine management system Fuel type in RON Maximum injection pressure in bar CO2 emission in g/km Emissions standard Ignition sequence Knock control Charging Exhaust gas recirculation Intake manifold flaps Intake camshaft adjustment Exhaust camshaft adjustment High pressure injectors (FSI) Injectors in the intake manifold (MP) Secondary air system Audi valvelift system (AVS) in exhaust Rotary slide valve Regulated oil pump Tumble Drumble4)CJEB longitudinal 1798 125 at 3800 – 6200 320 at 1400 – 3700 82.5 84.1 9.6 : 1CJSA transverse 1798 132 at 5100 – 6200 250 at 1250 – 5000 82.5 84.1 9.6 : 1CJSB transverse 1798 132 at 4500 – 6200 280 at 1350 – 4500 82.5 84.1 9.6 : 1484848951), 2)951), 2)952)EU 5 1–3–4–2 yes yes internal (camshaft adjustment) yes yes yes yes yes no yes yes yes yes noEU 5 plus 1–3–4–2 yes yes internal (camshaft adjustment) yes yes yes yes yes no yes yes yes yes noEU 5 plus 1–3–4–2 yes yes internal (camshaft adjustment) yes yes yes yes yes no yes yes yes yes noUnleaded RON 91 petrol can also be used, but results in slight loss of power. E25 compatible (models dating from week 40/2012 onwards) 3) Unleaded RON 95 petrol can also be used, but results in slight loss of power. 4) Drumble see page 591) 2)62.0l TFSI engineEngine code Installation position Displacement in cm3 Power output in kW at rpm Torque in Nm at rpm Bore in mm Stroke in mm Compression ratio Crankshaft Main crankshaft bearing diameter in mm Engine management system Fuel type in RON Maximum injection pressure in bar CO2 emission in g/km Emissions standard Ignition sequence Knock control Charging Exhaust gas recirculation Intake manifold flaps Intake camshaft adjustment Exhaust camshaft adjustment High pressure injectors (FSI) Injectors in the intake manifold (MP) Secondary air system Audi valvelift system (AVS) in exhaust Rotary slide valve Regulated oil pump Tumble Drumble4)CNCB longitudinal 1984 132 at 4000 – 6000 320 at 1500 – 3800 82.5 92.8 9.6 : 1CNCD longitudinal 1984 165 at 4500 – 6250 350 at 1500 – 4500 82.5 92.8 9.6 : 1CJXC transverse 1984 221 at 5500 – 6200 380 at 1800 – 5500 82.5 92.8 9.3 : 1525252951), 2)951), 2)982), 3)EU 5 1–3–4–2 yes yes internal (camshaft adjustment) yes yes yes yes yes no yes yes yes no yesEU 5 1–3–4–2 yes yes internal (camshaft adjustment) yes yes yes yes yes no yes yes yes no yesEU 6 1–3–4–2 yes yes internal (camshaft adjustment) yes yes yes yes yes no yes yes yes no yes7Engine mechanicalsOverviewIn addition to significantly reducing the weight of the engine block, a second cooling-side oil gallery has been developed for the electrically switchable piston cooling jets. The cross-sections of the coolant and oil return lines have been modified and the position of the knock sensors has also been optimised. The balancer shafts are in part roller bearing mounted to ensure that they are robust enough for use in a start-stop system or hybrid applications. They are therefore mounted in antifriction bearings in one place and in roller bearings in two places. At the same time, the friction, weight and inertia of the balancer shafts have been reduced. The oil return line on the "hot" side of the engine has been completely reconfigured.Weight saving measures (1.8l TFSI engine)The third generation of the EA888 engine family delivers a total weight saving of approximately 7.8 kg. To achieve these savings, the following components have been optimised or are used for the first time: • Thin-walled engine block and elimination of the separate coarse oil separator • Cylinder head and turbocharger • Crankshaft (with smaller main bearing diameters and four counterweights) • Die cast aluminium oil pan top section (including aluminium bolts) • Plastic oil pan bottom section • Aluminium bolts • Balancer shafts (in part roller bearing mounted)Engine blockThe engine block has been radically revised. The main aim was to save weight. For this purpose, wall thickness has been reduced from approx. 3.5 mm to 3.0 mm. In addition, the coarse oil separator function has been integrated into the engine block. The engine block delivers a total weight saving of 2.4 kg compared to the second generation variant. Internal friction has also been reduced. Key modifications are a reduction in main bearing diameter and enhanced balancer shaft bearings. Other modifications over the second generation engine are: • Second pressurised cooling-side oil gallery for the electrically switchable piston cooling jets • Modified coolant and oil return line cross-sections • Optimised, long coolant jacket • Oil cooler supply via cylinder head coolant return line • Optimised knock sensor positionings • Improved balancer shaft bearingsSealing Sealing is provided on the power output side by a sealing flange which is coated a liquid sealant and attached to the engine block by aluminium bolts. The timing case cover is also coated with a liquid sealant.8OverviewTiming case cover Knock sensor 1 G61Oil pressure switch, stage 3 F447 Sealing flange, power output sideEngine speed sender G28 Cast iron cylinder blockOil pan top section with baffle plate Oil pressure control valve N428Regulated oil pumpHoneycomb insertSealOil level and temperature sensor G266 Oil pan bottom section606_028Oil panOil pan top section The oil pan top section is made from die cast aluminium. The oil pump and the honeycomb insert for oil intake and oil return are integrated into it. The oil pan top section also accommodates the pressurised oil ducts and the two-stage oil pump control valve. It is sealed off from the engine block with a liquid sealant and attached by aluminium bolts. To further enhance the acoustic characteristics of the engine assembly, the main bearing covers are bolted onto the oil pan top section.Oil pan bottom section The oil pan top section is made from plastic. This gives a weight saving of approx. 1.0 kg. The oil pan bottom section is sealed by a moulded rubber gasket and attached by steel bolts. The oil level and temperature sender G266 is integrated into the oil pan top section. The oil drain screw is also made from plastic (bayonet lock).9Crank train (1.8l TFSI engine)When work began on development of the crank train the focus was on reducing friction and weight.PistonSnap ringGudgeon pinCon-rod (cracked)Upper con-rod bearing shellCrankshaftLower con-rod bearing shell606_030eMediaCon-rod bearing coverAnimation showing the crank train and sprocket chain drive, including the drive mechanism for the regulated oil pump and coolant pump.10PistonPiston clearance has been increased in order to reduce friction during the warm-up phase. A wear-resistant piston skirt coating is also used. Upper piston ring = Middle piston ring = Upper piston ring = taper face ring / on 2.0l engines Rectangular ring, asymmetrically barrelled taper face ring oil control ring (two piece, double bevelled spiral expander ring)Con-rods/gudgeon pinsThe con-rods are designed as cracked con-rods. As is the case with the main bearings, two-component lead-free bearings are used in the con-rod big end. A significant modification is the elimination of the bronze bushing in the con-rod small end. The entire engine is therefore equipped with lead-free bearings. For the first time in a passenger car engine, the con-rod is fitted without using a bearing bush in a special process patented by Audi. The gudgeon pin is joined directly to the steel inside the con-rod and to the aluminium alloy inside the piston. A special surface coating is applied to the gudgeon pin for this purpose. This is known as a DLC* coating.Crankshaft (1.8l TFSI engine)Compared to the second generation engine, the main bearing diameters of the crankshaft have been reduced from 52 mm to 48 mm, and the number of counterweights has been reduced from eight to four. This has reduced the weight of the crankshaft by 1.6 kg. The main bearing shells are configured as two-layer lead free bearings at the top and bottom. This ensures that the crankshaft is suitable for start-stop operation.Cradle supportThe main bearing covers are bolted into the oil pan top section. This modification enhances the comfort attributes of the engine in terms of acoustics and vibration.Engine block Cradle supportOil pan top section Bolting from below606_027Side bolting11Chain driveThe basic configuration of the chain drive has largely been adopted from the second generation variant. However, it too has been systematically improved. Due to the reduction in friction and lower oil consumption, less power is needed to drive the chain mechanism. The chain tensioners have accordingly been adapted for lower oil pressures. It might not be obvious at first glance, but there are a number of changes which are relevant to customer service. They pertain, firstly, to the chain assembly procedure and, secondly, also necessitate the use of various new special tools. In addition, an adaptation procedure has to be carried out using the diagnostic tester after doing work on the chain drive. This entails measuring and making allowance for component tolerances in the chain drive for diagnostic reasons.Camshaft adjuster ExhaustExhaust camshaft with Audi valvelift system (AVS)High pressure fuel pumpCamshaft adjuster IntakeChain drive606_002Regulated oil pumpBalancer shaft, in part roller bearing mountedCoolant pump12Balancer shaftsIn addition to reducing mass, the balancer shafts have been modified so they partially run in roller bearings. This has resulted in a marked reduction in friction, which is effective at low oil temperatures in particular. This modification also increases the robustness of the balance shafts in start-stop and hybrid operation.Ring Needle bearingNeedle cageSliding railRingIdler gear Tooth chainSliding rail606_029Crankshaft sprocket Tensioning rail Screw-in tensionerNote In the event of damage, a repair set comprising both balancer shafts together with needle cages is available via ETKA. The small needle bearings currently cannot be replaced using service resources.13Auxiliaries mounting bracketOil filter and oil cooler holders are integrated into the engine auxiliaries mounting bracket. The auxiliaries mounting bracket contains oil ducts and coolant ducts routed to the oil cooler. The oil pressure switch, the electrical switching valve of the piston cooling jets and the poly-V belt tensioning device are also integrated into it. The oil filter cartridge is accessible from above and so easy to service. To ensure that no oil is discharged when changing the filter, a sealing element is opened when the filter is released, allowing the oil to flow back into the oil pan.Design (shown using the transverse mounted 1.8l TFSI engine as an example)Oil ductsOil supply line from lube oil cooler to oil filter and engineOil filter cartridgeOil pressure switch F22To the mechanical valve of the piston cooling jetsControl valve for piston cooling jets N522 Oil supply to the engineOil pressure switch for reduced oil pressure F378Oil return duct to oil pan for: −− venting the mechanical valve of the piston cooling jets −− draining off raw oil when changing the oil filter606_026Oil supply from the oil pumpAutomatic poly-V belt tensioning deviceOil supply to the piston cooling jets Cooling jet switching valve vent Oil supply to the lube oil coolerCoolant ducts The oil supply line for the oil cooler is also integrated into the auxiliaries mounting bracket.Engine oil coolerFrom engineTo engine temperature control element N493606_055 14Cylinder headThe most eye-catching new component of the engine is the cylinder head, which has been completely revamped. For the first time in turbocharged diesel injection engines, use is made of an exhaust cooling system integrated into the cylinder head, as well as an exhaust routing system.VVT actuators 1 – 8 F366 – F373Ignition coils 1 – 4 with power output stage N70, N127, N291, N292Exhaust camshaft with Audi valvelift systemCamshaft adjuster IntakeIntegrated cooling ductsGas ducts to exhaust turbochargerCamshaft adjuster Exhaust606_006Reference To find out more about the variable valve timing system, refer to Self Study Programme 255 "The 2.0 l R4 and 3.0 l V6 engines".15Design123456 7981011 1213141516 16 18606_03117Key: 1 2 3 4 5 6 7 8 9 Hall sender 3 G300 Cylinder head cover VVT actuators 1 – 8 F366 – F373 Intake camshaft Intake camshaft adjuster Roller-type cam follower Support element Intake valve Exhaust camshaft 10 11 12 13 14 15 16 17 18 Exhaust camshaft adjuster Exhaust valve Hall sender G40 Port dividers Coolant temperature sender G62 Cylinder head Anti-freeze plug Stud bolt of integral exhaust manifold Cylinder head gasket16Sealing Steel bolts are used to attach the cylinder head cover. The cylinder head is sealed with a liquid sealant. The engine block is sealed off from the cylinder head by a two-layer metal cylinder head gasket. Sealing is provided on the timing side by a plastic chain case cover, into which the oil filler cap is now integrated.Audi valvelift system (AVS)The Audi valvelift system has been developed to optimise the charge cycles in internal combustion engines. The system was launched in the 2.8l V6 FSI engine of the Audi A6 ’05 in late 2006. To improve the torque characteristic, the proven AVS Audi valvelift system (two-stage valve lift switching) has been adopted from the second generation 2.0l TFSI engine (predecessor engine) (SSP 436).Camshaft adjusterAnother key modification is the use of a camshaft adjuster on the exhaust camshaft. This maximises the scope for charge cycle management. The AVS system and the exhaust camshaft adjustment make it possible to adapt to the various charge cycle requirements at full and partial throttle. The result is rapid torque delivery. The high torque level of up to 320 Nm across a wide rpm range allows the gearbox transmission ratios to be adapted differently (downspeeding). This makes for better fuel economy.Other modifications: • • • • • • • Long spark plug threads New pencil ignition coils Weight-optimised camshafts Optimised roller cam followers (for reduced friction) Reduced spring forces in valve gear New oil filler cap integrated into the upper chain case Coolant thermostat G62 integrated into the cylinder head (ITM) • Repositioned high pressure pump • Improved fine oil separator • The turbine housing of the exhaust turbocharger is bolted directly onto the cylinder head • Optimisation of the intake ports • Improvement of the fuel injection components including sound insulationReference To find out more about the functions of the Audi valvelift system, refer to Self Study Programme 411 "Audi 2.8l and 3.2l FSI engine with Audi valvelift system".Note There are also several changes relevant to assembly work on the cylinder head. For example, the cylinder head bolt must be removed in order to take off the cylinder head. For a detailed description of the procedure, please refer to the relevant workshop manual.17Integral exhaust manifoldA significant modification is the cooled exhaust manifold with ignition sequence separation, which is now directly integrated into the cylinder head. Thanks to the use of the integral exhaust manifold, the exhaust temperature upstream of the turbine is significantly lower than in a conventional manifold. In addition to this, a highly heat-resistant turbocharger is used. As a result of this combination, there is no longer any need for full-throttle mixture enrichment to conserve the turbine, particularly at high engine speeds. This can considerably improve fuel economy during normal vehicle operation and even when driving in a sporty fashion. In addition, the integral exhaust manifold facilitates rapid coolant heating and, therefore, is an integral part of the thermal management system.Exhaust ducts The exhaust ducts are designed in such a way that the exhaust gases flowing from the exhaust cylinder do not interfere with the purging process in another cylinder. The full energy of the exhaust gas flow is therefore available for driving the exhaust turbocharger turbine. The exhaust ports of cylinders 1 and 4 as well as cylinders and 3 converge at the transition to the exhaust turbocharger.Integral exhaust manifoldGas ducts to exhaust turbochargerExhaust turbocharger606_00718Cooling of the integral exhaust manifoldThe integral exhaust manifold facilitates rapid heating of the coolant and, therefore, is an integral part of the thermal management system. During the warm-up phase, heat is transferred to the coolant within a very short period of time. This heat is directly utilised to heat the engine and occupant cell. Due to the reduced heat loss, the downstream components - oxygen sensor, exhaust turbocharger and catalytic converter - are able to reach their optimal operating temperature more quickly. The system goes into cooling mode even after a short warm-up phase. This is necessary because otherwise the coolant in proximity to the integral exhaust manifold would boil off very quickly. For this reason, the coolant thermostat G62 is fitted at the hotest point in the cylinder head.Intake sideMain water jacketUpper coolant tractLower coolant tractExhaust port with flange connecting to turbochargerExhaust side606_032eMedia Animation showing the cylinder head and the integral exhaust manifold.19Positive crankcase ventilationThe positive crankcase ventilation system has also been systematically improved. The engine block pressure to ambient air pressure ratio is configured for a high pressure gradient. This has a significant positive effect on lube oil consumption. Furthermore, a strong emphasis has been placed on reducing the number of components. On the exterior of the engine, for example, there is now only one pipe for the discharge of cleaned blow-by gases. The system comprises the following components: • Coarse oil separator in engine block • Fine oil separator module, bolted onto the cylinder head cover • Hose for the discharge of cleaned blow-by gases • Oil return line in the engine block with shutoff valve in the oil pan honeycomb insert.OverviewEntry of blow-by gases into the intake manifold module (in naturally aspirated mode) Entry of blow-by gases into the exhaust turbocharger (in charging mode) Fine oil separator moduleOil return duct from the fine oil separator606_043Oil return line shut-off valve for the fine oil separator (below the oil level in the oil pan)20Coarse oil separatorOil return duct from the fine oil separator (below the oil level in the oil pan)Coarse oil separationThe coarse oil separator function is an integral part of the engine block. A portion of the oil is separated by changing the direction of flow in a labyrinth. The separated oil returns to the oil pan via the return duct in the engine block. The end of the duct is below the oil level.Fine oil separationThe coarsely cleaned blow-by gases flow from the engine block into the fine oil separator module through a duct in the cylinder head. Here, the gases are first of all cleaned in a cylone separator. The separated oil from the cyclone separator returns to the oil pan through a separate duct in the engine block. The end of this duct is below the oil level. A shutoff valve prevents oil from being drawn in from the oil pan in unfavourable pressure conditions. A sporty driving style (high transverse acceleration) could potentially expose the immersed oil return line because of the oil sloshing around inside the oil pan. In this case, too, the shutoff valve keeps the oil return line closed. The valve in question is a shutter valve. The cleaned blow-by gases are fed into the combustion chamber via the single-stage pressure control valve. The pressure control valve is rated for a pressure difference of –100 mbar relative to the ambient air. The point at which the blow-by gases are admitted into the combustion chamber is dictated by the pressure ratio in the air supply system.Bypass valve opens at excessively high blow-by flow rates (very high engine speed) oil is also separated here by the high flow ratePressure control valveActivated charcoal filter connection606_045Blow-by duct from the engine block and cylinder headCyclone separatorBlow-by line to exhaust turbocharger (charging mode)21Supply of cleaned blow-by gases to the combustion chamberAfter the blow-by gases have been cleaned of fine oil droplets and allowed to flow onwards by the pressure control valve, they are admitted into the combustion chamber. Gas flow is controlled automatically by self-actuating non-return valves integrated into the fine oil separator module. The non-return valves return to their initial position when the engine is shut off. The non-return valve facing the exhaust turbocharger is open, while the non-return valve facing the intake manifold is closed.Faulty installation detection Governments in several markets, such as North America, require that safeguards be provided to detect faulty installation of components relevant to exhaust emissions. If the venting line on the crankcase breather module is not or incorrectly installed, the faulty installation detection contact opens. Given that this contact is connected directly to the air intake side of the cylinder head, the engine immediately begins to induce unmetered air. This is detected by the lambda control system.Full throttle operation (charging mode) Since a vacuum is now present throughout the charge air tract, non-return valve 1 closes. The difference between the pressure inside the crankcase and the pressure on the intake side of the turbocharger causes non-return valve 2 to open. The cleaned blow-by gases are induced by the compressor.Bypass valveCyclone separatorNon-return valve 2 (open)Non-return valve 1 (closed)606_047Blow-by line to exhaust turbocharger (charging mode)22Idle and partial throttle operation (naturally aspirated mode) In naturally aspirated mode non-return valve 1 is opened by the vacuum present in the intake manifold and non-return valve 2 is closed. The cleaned blow-by gases are admitted directly into the combustion chamber via the intake manifold.Blow-by gas intakePressure control valveBlow-by line to intake manifold (naturally aspirated mode)606_046PCV valveNon-return valve 2 (closed)Non-return valve 1 (open)Positive crankcase ventilation (PCV*)The crankcase breather is installed in a module on the valve cover together with the fine oil separator and the pressure regulator. The crankcase is vented via the venting line connected upstream of the turbine and a calibrated port in the crankcase breather valve. The system is therefore designed in such a way that it is only vented when the engine is running in naturally aspirated mode.Calibrated bore for positive crankcase ventilation PCV valve diaphragm (removed)Activated charcoal filter connectionCyclone separatorBlow-by line to intake manifold (naturally aspirated mode)Blow-by gas intake606_08323Oil supplySystem overviewKey: A B C D E F 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Camshaft bearing Support element Balancer shaft bearing Exhaust balancer shaft bearing 1 Con-rod Main bearings 1 – 5 Exhaust camshaft timing adjust. valve 1 N318 Hydraulic vane cell adjuster (exhaust) Non-return valve, integr. into bearing bridge Mesh oil filter Intake camshaft timing adjust. valve -1- N205 Hydraulic vane cell adjuster (intake) Non-return valve, integrated into cyl. head Fine oil separator Vacuum pump Flow restrictor Lubrication of cam for high pressure fuel pump Oil cooler Non-return valve, integrated into oil filter Oil filter Oil drain valve Oil pressure switch F22 (2.3 – 3.0 bar) Oil pressure switch for reduced oil press. F378 (0.5 – 0.8 bar) Piston cooling jet control valve N522 Mechanical switching valve Chain tensioner for balancer shafts Chain tensioner for timing gear Exhaust turbocharger Coarse oil separator Oil pressure switch, stage 3 F447 Lubrication of gear step Oil level/oil temperature sensor G266 Cold start valve Non-return valve, integrated into oil pump Regulated oil pump Oil pressure control valve N428Bearing bridge A13 A 4253 A 6 4Auxiliaries mounting bracket12131418 15 16 1719High pressure circuit Low pressure circuitOil pan top section 2829 30 27 26 4 Oil pan bottom section248 Oil channelsAAAAA94 B B B B B B B B10 11 Vacuum pumpBBBBBBBBA 7AAACylinder head202122CDECEECE23FFFFF24 4 4C 25CCEngine block606_018 25Oil supplyThe pressurised oil circuit has also been systematically optimised and developed. The focal points were as follows: • Optimisation of the pressure ducts in the oil system, thereby reducing pressure losses while simultaneously increasing volume • Reduction of pressure losses in the pressurised oil tracts • Extension of the rpm range in the low pressure stage • Oil pressure reduction in the low pressure stage • Switchable piston cooling jets Altogether, these modifications have brought a noticeable reduction in friction within the engine assembly. Fuel economy has been improved still further.Oil pressure switch, stage 3 F447Oil coolerOil filterOil pressure switch for reduced oil pressure F378Oil pressure switch F22Control valve for piston cooling jets N522Auxiliaries mounting bracketOil pressure control valve N428Regulated oil pump606_003Piston cooling jetRaw oil Clean oil Switchable piston cooling jets26Modifications to the oil pump: • Modified pressure level • Higher efficiency • Modifications to the hydraulic control systemRegulated oil pumpThe basic functional principle of the oil pump derives from the second generation engine pump. The differences are as follows: • The hydraulic control system within the pump has been improved, thus enabling the pump to control oil flow with even greater precision. • The pump drive ratios have been modified (i = 0.96) so that the pump now runs more slowly.606_033CoverCold start valveDisplacement unitControl pistonControl springDriven shaftRetention valveDrive shaft with drive pump gear Driven pump gear (axially displaceable)Compression spring of displacement unitPump casingIntake manifoldMesh oil filter606_034Reference To find out more about the function and design of the regulated oil pump, refer to Self Study Programme 436 "Modifications to the chain-driven 4-cylinder TFSI engine".27Oil filler capThe cover is fitted in the chain case. In addition to having an easy opening and closing action, the cover seals the engine bay off from the environment in a safe and oil-tight way. Unlike the old design, the seal and the bayonet lock are functionally separate. The sealing face of the elastomer rectangular seal is smaller. Moreover, no relative movement occurs between the seal and the chain case cover when fitting the cover onto the engine. This revised design minimises the actuation forces. The bayonet lock captively secures the cover at 90° intervals.Top part of oil filler cap with bayonet lockSpringBottom part of oil filler capRectangular seal606_082Switchable piston cooling jetsIt is not necessary to clean the piston crowns in every operating situation. Fuel economy is further improved by selectively shutting off the piston cooling jets. A further reason for eliminating the springloaded piston cooling jets is the lower overall oil pressure level. The switchable piston cooling jets system comprises the following components: • Additional pressurised oil duct in cylinder block • New piston cooling jets without spring valves; there are jets with two different internal diameters (the jets of the 1.8l TFSI engines have smaller diameters). • Oil pressure switch, stage 3 F447 (closes at 0.3 – 0.6 bar) • Piston cooling jet control valve N522 • Mechanical switching valveMap for piston cooling jets The piston cooling jets are activated only when required. This calculation is made on the basis of a special engine map stored in the engine control unit. The piston cooling jets can be activated both in the low and high pressure stages. The key calculation factors are: • Engine load • Engine speed • Calculated oil temperatureTorque [Nm]Engine speed [rpm]606_019Piston cooling switched off (oil temperature 50 °C)28Piston cooling switched off (oil temperature 50 °C)Piston cooling jets deactivated The control valve for the piston cooling jets N522 is energised by the engine control unit. The control valve for the piston cooling jets N522 is powered via terminal 87. The connection to ground is made by the engine control unit, which thereby makes the electrical circuit. This causes N522 to open the control channel for the mechanical switching valve. Pressurised oil now acts directly upon the control piston of the mechanical switching valve from both sides. The spring displaces the mechanical switching valve and thus closes the duct to the oil gallery of the piston cooling jets.Oil pressure switch for reduced oil pressure F378 Oil filter mandrel Oil gallery to the piston cooling jets switched offControl channel606_004Control valve for piston cooling jets N522, energisedMechanical switching valve, shuts off the duct to the oil gallery of the piston cooling jetsPiston cooling jets activated The piston cooling jets are activated by de-energising N522. This closes the control channel to the mechanical switching valve. Given that the switching valve is now on a side which is subjected to oil pressure, it moves and thereby opens the duct to the oil gallery of the piston cooling jets. The spring in the switching valve is pretensioned. The spring force in the switching valve holds the oil gallery to the piston cooling jets shut at oil pressures of 0.9 bar or higher. To enable the switching valve to immediately return to its initial position after the control valve for the piston cooling jets N522 is shut off, it is important that the oil from the control piston drain off quickly. For this purpose, there is a separate duct which allows the oil to drain pressurelessly into the engine oil pan. This is the same duct as that into which the oil drains when replacing the oil filter.Oil gallery to the piston cooling jets switched on606_005Control valve for piston cooling jets N522, de-energisedSwitching valve venting lineMechanical switching valve, opens the port to the oil gallery of the piston cooling jetsFunction monitoring When the piston cooling jets are switched on, the contact in the oil pressure switch, stage 3 F447 closes. The switch is located at the end of the oil gallery for the piston cooling jets (see page 26, Fig. 606_003). The following faults can be detected by the oil pressure switch: • No oil pressure is present at the piston cooling jets despite being requested • Faulty oil pressure switch • Oil pressure is present despite deactivation of piston cooling jets The following electrical faults can be detected in the control valve for the piston cooling jets: • Open circuit; piston cooling jets are always on • Short circuit to ground; piston cooling is off • Short circuit to +; piston cooling is always on Faults resulting in loss of piston cooling lead to the following limp home reactions: • Torque and engine speed are limited by the engine control unit • The regulated oil pump has no low oil pressure stage • A message indicating that the engine speed is limited to 4000 rpm is displayed in the instrument cluster, a single beep signal sounds and the EPC lamp comes on.29Cooling systemSystem overviewThe cooling system is adapted to match the vehicle specification and engine type. A distinction is made between longitudinal and transverse mounting, gearbox version, and whether or not the vehicle is equipped with an auxiliary heater.Coolant circulationThe 1.8l TFSI is given here as an example. It is in the longitudinal mounted version with manual gearbox and without auxiliary heater. Numbers from the key on page 31 have been added to the labels in the diagram.Connections from and to heater heat exchanger 1Rotary slide valve 2 8Rotary slide valve 1 8Coolant expansion tank 6Coolant circulation pump V50 4Gearbox heating connectionDucts of the integral exhaust manifoldExhaust turbocharger 9606_009Engine oil cooler 11Radiator 15Note For vehicle-specific terminal diagrams, refer to the applicable workshop manual.301.8l TFSI longitudinal mounted engine with manual gearbox and without auxiliary heater1234 567891011121315 14606_023Cooled coolant Heated coolant ATF Key: 1 2 3 4 5 6 7 8 Heater heat exchanger Gear oil cooler Climatronic coolant shutoff value N422 activated Coolant circulation pump V50 Gearbox coolant valve N488 Coolant expansion tank Coolant temperature sender G62 Coolant pump with engine temperature control element N493 (rotary slide valves 1 and 2) 9 10 11 12 13 14 15 Exhaust turbocharger Integral exhaust manifold Engine oil cooler Radiator fan V7 Radiator fan 2 V177 Coolant temperature sensor at radiator outlet G83 Radiator31Innovative Thermal Management (ITM)The complete coolant circuit was revised during further development of the engine. The main emphasis was on rapid engine heating, reduction in fuel consumption by rapid and thermodynamically optimised engine temperature regulation, as well as heating of the vehicle interior when required. The two key components of the innovative thermal management system are the exhaust manifold integrated into the cylinder head (see "Cylinder head") and the engine temperature control element N493 described below. It is fitted as a module on the cooling side of the engine, together with the coolant pump.Coolant temperature at ambient temperature (20 °C) Key:85 °C 90 °C 95 °C 100 °C 105 °CTorque [Nm]606_040Engine speed [rpm]Rotary slide valve module and coolant pumpSupply line to radiator Coolant pumpRotary slide valve 2Toothed belt drive gearToothed belt for coolant pump606_035Cover Return line from radiator Rotary slide valve 1Coolant pump drive gearReturn line from heater, exhaust turbocharger and gearbox32Engine temperature control element N493 (rotary slide valve)The engine temperature control element N493 is identical for longitudinal and transverse mounted engines with displacements of 1.8 l and 2.0 l. It regulates coolant flow by means of two mechanically coupled rotary slide valves. The angular position of the rotary slide valves is regulated according to various engine maps stored in the engine control unit. Various switching positions can be implemented by configuring the rotary slide valves accordingly. This allows rapid heating of the engine, which, in turn, results in lower friction and higher fuel economy. In addition, variable engine temperatures between 85 °C and 107 °C are possible.1234589671011606_036Key: 1 2 3 4 5 Drive for engine temperature control element N493 with sender Connecting piece for radiator supply line Connecting piece to lube oil cooler connection Idler gear Rotary slide valve 2 6 7 8 9 10 11 Shaft for rotary slide valve 1 Rotary slide valve housing Expanding material thermostat (failsafe thermostat) Sealing package Connecting piece for return line from radiator Rotary slide valve 133Function of engine temperature control element N493 A DC electric motor drives the rotary slide valve. The motor is activated by the engine control unit by means a PWM signal (12 V). The activation frequency is 1000 Hz. The activation signal is new. It is a digital signal with a similar configuration to a CAN signal. The motor is activated until the rotary slide valve is in the position specified by the engine control unit. A positive activation signal (measured value in diagnostic tester) causes the rotary slide valve to rotate in the "open" direction. The electric motor drives rotary slide valve 1 via a worm gear with a high reduction ratio. It controls the coolant flow in the oil cooler, cylinder head and main radiator (the gear oil cooler, exhaust turbocharger and heater return line are unregulated). Rotary slide valve 2 is connected to rotary slide valve 1 via a lantern gear. The gear is designed in such a way that rotary slide valve 2 engages and disengages in defined angular positions of rotary slide valve 1. Rotary slide valve 2 (which opens the coolant flow through the engine block) begins to rotate when rotary slide valve 1 is in an angular position of approx. 145°. Rotary slide valve 1 disengages again in an angular position of approx. 85°. In this position, rotary slide valve 2 has completed its maximum rotation and the engine block cooling circuit is fully open. The movements of the rotary slide valve are limited by mechanical stops.The warmer the engine, the further the rotary slide valve rotates. This causes various channels to open into variable cross-sections.To determine the exact position of the rotary slide valve and to detect malfunctioning, a rotation angle sensor is mounted on the rotary slide valve control board. This sensor supplies a digital voltage signal (SENT*) to the engine control unit. The position of rotary slide valve 1 can be read out in the measured data using the diagnostic tester.Engine outletEngine inletRotary slide valve 2Engine temperature control element N493Supply line to radiator606_010Return line from oil cooler Worm gearRotary slide valve 1Belt drive Coolant pump Return line from heater, exhaust turbocharger and gearbox Return line from radiator34Activation strategyThe function of the complete coolant circuit during the engine heating phase is described here. This description applies to engines in the Audi A4 ’12.Heating To warm up the engine, rotary slide valve 1 is moved into the 160° position. In this position, the lube oil cooler and main radiator return line connections on rotary slide valve are closed. Rotary slide valve 2 closes the connection to the engine block. The Climatronic coolant shutoff value N422 and the gearbox coolant valve N488 are initially closed. The coolant run-on pump V51 is not activated, with the result that the engine block is unable to circulate coolant. Depending on engine load and speed, coolant circulation is stopped up to a maximum temperature of 90 °C.606_062Independent heating If a heating request is issued, the Climatronic coolant shutoff value N422 and the coolant run-on pump V51 are activated. As a result, coolant flows through the cylinder head, the turbocharger and the heater heat exchanger.606_063Mini volumetric flow This function safeguards against overheating of the cylinder head (integral exhaust manifold) and the turbocharger when coolant circulation is stopped in the engine block. For this purpose, rotary slide valve 1 is moved into a position of approx. 145°. From this position onwards, the lantern gear engages rotary slide valve 2 and starts to open it. A small portion of the coolant now flows through the engine block into the cylinder head, through the turbocharger and back to the coolant pump via the rotary slide valve module. The second partial flow flows to the heater heat exchanger via the coolant shutoff valve N82 if required. The coolant run-on pump V51 is activated only when heating is requested. Engine friction is further minimised during the warm-up phase due to the fact that the coolant heats up very quickly.606_06435Activation of lube oil cooler warm-up The lube oil cooler is additionally activated during the heating phase. The lube oil cooler connection begins to open when the rotary slide valve 1 moves beyond an angular position of 120°. Parallel to this, rotary slide valve 2 continues to open, thus increasing coolant flow through the engine block. The lube oil is additionally heated by the selective activation of the lube oil cooler.606_065Gear oil heating Once the internal combustion engine has heated up sufficiently, the gearbox coolant valve N488 opens to heat the gear oil with the surplus heat. The gear oil heating function is activated at a coolant temperature of 80 °C without heating and 97 °C with heating.606_066Temperature control via main radiator At low engine speeds and loads, the coolant is heated to a temperature 107 °C so as to minimise engine friction. The coolant temperature is then reduced to 85 °C with increasing engine load and speed. For this purpose, rotary slide valve 1 is set to an angular position of between 85° and 0°, depending on cooling requirements. The main radiator return line connection is fully open in the 0° position of the rotary slide valve.Partial throttle rangeFull throttle range606_067 36606_068Run-on function after shutting off the engine The run-on function is started according to the engine map in order to prevent the coolant in the cylinder head and turbocharger from boiling after shutting off the engine, and to avoid unnecessary cooling-down of the engine. This function remains active for up to 15 minutes after shutting off the engine. For this purpose, the rotary slide valve is moved into the "run-on position" (160 – 255°). The coolant temperature is also controlled during the run-on phase. If maximum run-on is requested (255°) and the nominal coolant temperature is correspondingly low, the main radiator return connection is opened, but the connection to the engine block is closed by means of rotary slide valve 2. In addition to this, coolant run-on pump V51 and coolant shutoff valve N82 are activated. The coolant flow is now divided into two partial flows. The first partial flow passes through the cylinder head to V51 and the second partial flow passes through the rotary slide valve via the turbocharger, and then through the main radiator and back to the coolant run-on pump V51. Coolant does not flow through the cylinder crankcase in the run-on position. This function significantly reduces the "on" time of the run-on function without producing excessive heat loss.606_077Fault If the rotation angle sensor fails, the rotary slide valve is fully activated (maximum engine cooling). If the DC motor is faulty or the rotary slide valve is sticking, an engine speed and torque limiter is activated depending on the position of the rotary slide valve. Other reactions: • A message indicating that the engine speed is limited to 4000 rpm is displayed in the instrument cluster, a single beep signal sounds and the EPC lamp comes on. • The actual coolant temperature is displayed in the instrument cluster • The coolant shutoff valve N82 opens • The coolant run-on pump V51 is activated in order to ensure that the cylinder head is cooled. If the temperature in the rotary slide valve exceeds 113 °C, an expanding material thermostat in the rotary slide valve opens a bypass to the main radiator so that coolant can flow through the main radiator (see page 33, Fig. 606_036). As a result, it is possible to continue driving in the event of a fault.eMedia Animation showing the innovative thermal management system and the function of the rotary slide.37Function diagram of engine temperature control element N493Connections on the engine temperature control element N493: 1 2 3 4 5 Sensor – (sender ground connection in engine wiring loom) Sensor signal Sensor + (5 V connection in engine wiring loom) Actuator – Actuator + 23451606_021Gearbox coolant valve N488The gearbox coolant valve N488 controls the flow of warm coolant from the engine to the gear oil cooler. For example, it is fitted in the Audi A5 ’12 with manual gearbox. When required, the solenoid valve is activated through the application of on-board voltage by the engine control unit. It is held open by mechanical spring force when not activated and closes when the engine is started. The coolant flow to the gearbox opens at a coolant temperature of 80 °C and closes again at 90 °C. This helps the manual gearbox to attain its optimal friction temperature.Electrical connectionCoolant flow to the engineSolenoid coil606_022PistonCoolant flow to the ATF cooler38Coolant circulation pump V50This pump is used as a circulation pump for the heater heat exchanger in vehicles with longitudinal mounted engines and is activated by the Climatronic control unit J255 by means of a PWM signal. It is diagnosable via the Climatronic control unit J255.Function When the coolant circulation pump V50 is running, the coolant is drawn in from the engine by the air conditioner heat exchanger and the coolant shutoff valve via the coolant hose and recirculated to the engine via the coolant hose. When the ignition is on, the coolant circulation pump V50 is activated depending on the coolant temperature and the setting of the air conditioner operating and display unit. The trim version of the vehicle is selected from the coding and adaptation functions (e.g. auxiliary heater installed).606_056Coolant circulation pump V50Climatronic coolant shutoff value N422The coolant shutoff valve is fitted in longitudinal mounted engines without an auxiliary heater. The valve opens and closes coolant flow to the vehicle's heater heat exchanger, see page 31, Fig. 606_023.Function and is identical to the gearbox coolant valve N488 (see page 38 ). It is open (allowing coolant to flow) when it is not being activated and closes when activated. The valve is opened by mechanical spring force and closes when the engine is started. The valve opens when the heating, run-on cooling and start-stop functions are activated. It is switched on/off by the Climatronic control unit J255. The Climatronic coolant shutoff value N422 integrated into J255 must be correctly adapted.Coolant run-on pump V51The pump is fitted in vehicles with transverse mounted engines. It is identical to the coolant circulation pump V50 in vehicles with longitudinal mounted engines and is activated by the engine control unit by means of a PWM signal. The coolant run-on pump V51 is activated by the engine control unit at the request of the operating unit (heater control unit J65) or the Climatronic control unit J255. It also assists the engine coolant pump in order to increase coolant flow through the heater heat exchanger at defined engine speeds, thus providing higher heating output. Moreover, the temperature in the exhaust turbocharger can be reduced more quickly, thus extending the life of the lube oil.Coolant shutoff valve N82The coolant shutoff valve N82 is activated by the engine control unit and is fitted in the Audi A3 ’13 with auxiliary heater, among other models. Depending on the setting on the operating unit (heater control unit J65) or the Climatronic control unit J255, the coolant shutoff valve shuts off the coolant flow through the heater heat exchanger, e.g. to heat up the engine.Reference To find out more about the coolant circulation pump V50/V51, refer to Self Study Programme 616 "Audi 1.2l and 1.4l TFSI engines of the EA211 series".39Air supply and chargingSystem overviewC A B DEV465N249FG31 N316 J338 G186 G187 G188Exhaust gases Intake air (vacuum) Charge air (charge pressure) Wastegate (charge pressure)GG336G42 with G71606_025Key: A B C D E F G Exhaust flow Exhaust turbocharger Air filter Fresh air flow Wastegate valve Charge air cooler Intake manifold flaps G31 Charge pressure sensor G42 Intake air temperature sensor G71 Intake manifold pressure sensor G186 Throttle valve drive (electronic power control) G187 Throttle valve drive angle sender 1 with electronic power control G188 Throttle valve drive angle sender 2 with electronic power control G336 Intake manifold flap potentiometer J338 Throttle valve control unit N249 Turbocharger bypass valve N316 Intake manifold flap valve V465 Charge pressure actuatorNote The charge pressure actuator V465 must be replaced after removing the lock nut from the linkage. After replacement, the charge pressure actuator must be set using the diagnostic tester.40Air routing system for transverse mounted enginesExhaust turbocharger (B)Turbocharger bypass valve N249Charge pressure actuator V465Air filter (C)606_037Intake manifoldCharge air cooler (F) Intake manifold flap valve N316Intake manifold flap potentiometer G336Air intake (D)Intake air temperature sender G42 with intake manifold pressure sender G71 Throttle valve control unit J338Charge pressure sensor G3141Air routing system for longitudinal mounted enginesAir filterCharge pressure actuator V465Exhaust turbochargerIntake manifold flap valve N316Intake air temperature sender G42 with intake manifold pressure sender G71 Throttle valve control unit J338Intake manifoldAir intakeIntake manifold flap potentiometer G336Charge pressure sensor G31606_038Charge air cooler42Intake manifoldDue to the higher charge pressures, the intake manifold system integrated into the intake manifold has been completely revised. The angled, single-piece stainless steel shaft maximises the torsional rigidity of the pan-shaped flaps in the intake duct. The positioning of the flaps is detected by the intake manifold flap potentiometer G336 (non-contact rotation angle sensor). When open, the pan-shaped flaps are tensioned in the basic element in such a way as to minimise excitation by the air flow. The shaft is actuated electro-pneumatically by the engine control unit via the intake manifold flap valve N316 using a vacuum controlled cell (on/off control).Fuel metering valve N290 High pressure pump Vacuum cell for the charge motion flapsIntake air temperature G42 with intake manifold pressure sensor G71MPI injectorsIntake manifold flap potentiometer G336606_041FSI injectors Intake manifold flapsThrottle valve control unit J338Intake manifold flap valve N316FSI injectors606_04243Exhaust turbochargerAn all-new mono-scroll* exhaust turbocharger is used as a charging system. The use of a mono-scroll exhaust turbocharger improves full throttle response, particularly at high engine speeds. The twin-scroll ducting of exhaust gases at the cylinder head outlet is continued in the exhaust turbocharger to shortly before the turbine. Overall, this optimises ignition sequence separation (4 - 2 - 1) The exhaust turbocharger has the following features: • Electrical wastegate actuator (charge pressure actuator V465 with charge pressure actuator position sender G581) • Oxygen sensor upstream of turbine (oxygen sensor G39) • Compact cast steel turbine housing with twin-scroll inlet flanged directly onto the cylinder head • Compressor housing with integrated pulsation silencer and electrical diverter valve (turbocharger bypass valve N249) • Temperature resistant (Inconel*) turbine wheel rated for temperatures of up to 980 °C • Bearing housing with standard connections for oil and coolant • Milled compressor wheel for higher speed resistance and better acoustics • Turbine wheel configured as a Mixed Flow Turbine* made from Inconel 713 °CCharge pressure actuator V465From air filterOxygen sensor G39Turbocharger divert air valve N249Cylinder headIntegrated pulsation silencer606_013Engine blockTurbine housingWastegate valveTo charge air coolerIntegral exhaust manifoldSensors for detecting air mass and air temperature: • Charge pressure sender G31 (position 3) fitted in the air line between the charge air cooler and throttle flap. Its signal is utilised to control the charge pressure. • Intake air temperature sensor G42 with intake manifold pressure sender G71, air mass is measured using the pressure and temperature signals.44Charge pressure actuator V465An electrical wastegate actuator is used in an Audi turbocharged four-cylinder engine for the first time. This technology offers the following advantages over the previously used vacuum cells: • Faster and more precise response • Can be actuated independently of the charge pressure • Due to the higher closing force, the engine achieves its maximum torque of 320 Nm at a low engine speed of 1500 rpm. • The active opening of the wastegate at partial throttle allows the basic charge pressure to be reduced. The provides fuel savings of approx. 1.2 g CO2/km in the MVEG cycle. • Active opening of the wastegate during the heating phase of the catalytic converter increases the exhaust gas temperature upstream of the catalytic converter by 10 °C, resulting in lower cold start emissions. • The high adjustment rate of the electrical wastegate actuator allows the immediate build-up of charge p