TECHNICAL DOCUMENTATION
SSP 617 Audi RS 5 2010 and RS 4 Avant 2013 Power transmission

This PDF is currently unavailable.
Read document text
Self Study Programme 617 For internal use onlyAudi RS 5 ’10 and RS 4 Avant ’13 Power transmissionquattro drive with crown-gear centre differential and torque vectoringAudi Service TrainingTraction on a high level: quattro drive with crown gear centre differential and torque vectoring As with every RS model, the Audi RS 5 ’10 and the Audi RS 4 Avant ’13 employ the quattro full-time all-wheel drive to put the power from the 331 kW (450 HP) engine down onto the road. Both models have identical drivelines. An evolutionary version of the centre differential is utilised – the so-called crown gear centre differential. This compact and lightweight component has the ability to distribute power flow between the front and rear axles instantaneously, homogeneously and over a broad range; up to 70 percent can flow to the front axle and up to 85 percent to the rear axle.617_027The crown-gear limited slip differential works in conjunction with the torque vectoring system, which acts on all four wheels. If a wheel on the inside of the curve loses too much traction under dynamic driving conditions, the torque vectoring system brakes the wheel before unwanted levels of slip occur. Audi also offers the sports differential option, a mechanism that uses two overlapping ratios to actively distribute the power between the rear wheels.Power transmission is provided by the sporty 7-speed dual clutch gearbox 0B5 S tronic. In the case of the Audi RS 5 ’10 and Audi RS 4 Avant ’13, this gearbox has special characteristics which are explained in this Self Study Programme.617_028 2ContentsIntroductionPower transmission at a glance _ ____________________________________________________________________________________________________________________________ quattro drive __________________________________________________________________________________________________________________________________________________ Crown-gear differential – Torque vectoring _ _______________________________________________________________________________________________________________ Rear axle final drive unit 0BF – sports differential ________________________________________________________________________________________________________ Changing the ATF and axle oil _ _____________________________________________________________________________________________________________________________ 4 6 6 7 7Crown-gear differentialCrown-gear differential – Design and function ____________________________________________________________________________________________________________ 8 Asymmetric basic torque split ______________________________________________________________________________________________________________________________ 9 Asymmetric-dynamic torque split _________________________________________________________________________________________________________________________ 10 Operating instructions _ _____________________________________________________________________________________________________________________________________ 11Special features of the 0B5 gearboxSplined prop shaft _ _________________________________________________________________________________________________________________________________________ 12 ATF filter (pressure filter) __________________________________________________________________________________________________________________________________ 14 Changing the MTF ___________________________________________________________________________________________________________________________________________ 16 MTF temperature monitoring function ___________________________________________________________________________________________________________________ 18 Gear oil temperature sensor 2 G754 ______________________________________________________________________________________________________________________ 18 MTF temperature collective ________________________________________________________________________________________________________________________________ 20 Temperature intervals ______________________________________________________________________________________________________________________________________ 20 Cooling function _ ____________________________________________________________________________________________________________________________________________ 21 Safety function ______________________________________________________________________________________________________________________________________________ 21 Selector mechanism ________________________________________________________________________________________________________________________________________ 22Torque vectoringIntroduction _________________________________________________________________________________________________________________________________________________ 24 Working principle and function _ ___________________________________________________________________________________________________________________________ 25AnnexTest your knowledge ________________________________________________________________________________________________________________________________________ 28The Self Study Programme teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a Repair Manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. This content is not updated. For further information on maintenance and repair work, always refer to the current technical literature.!InformationReference3IntroductionPower transmission at a glanceThe latest generation of the quattro drive with crown-gear differential and torque vectoring was premiered on the Audi RS 5 and also imparts a high level of driving dynamics to the Audi RS 4 Avant. The S tronic (7-speed dual clutch gearbox 0B5) combines sportiness, dynamics and ride comfort with excellent overall efficiency. It is the ideal gearbox for both RS models. The operating logic of the selector for the sport program (speed S) has been reconfigured (refer to page 22). The 7 speed dual clutch gearbox 0B5 S tronic is described in detail in Self Study Programme 429 "Audi Q5 – Engines and Transmissions". There are currently seven Audi Service TV programmes from which you can obtain more information. You can find all of these programmes using the search string "0B5".Special characteristics and new features of the 7 speed dual clutch gearbox 0B5 – S tronicSeveral modifications came into effect from week 22/2010 The key modifications relevant to servicing are explained below.Axle flange with new sealing and fitting concept, refer to Self Study Programme 409 "Audi A4 ’08", page 30 ff.Rear axle final drive Optional: Rear axle final drive OBF – sports differential – refer to page 7 Standard: Rear axle differential 0BC4617_002Splined prop shaft – refer to page 12Limited slip centre differential – refer to page 8Reference The drive concept of the Audi RS 5 and Audi RS 4 Avant is identical to that of the B8 series (Audi A4/A5) in many respects. For information about the axle position and the new sealing and fitting concept of the axle flange for the rear axle differential, please refer to Self Study Programmes 392 "Audi A5" and 409 "Audi A4 ’08", as well as the Audi Service TV programme "Audi A5 Power Transmission" (broadcast on 02.2010). This information also applies to the Audi RS 5 and Audi RS 4 Avant and constitutes basic knowledge on this topic.5quattro driveTo celebrate the 30th anniversary of the quattro in 2010, Audi unveiled a new evolutionary stage of its full-time all-wheel drive for longitudinally mounted engines on the Audi RS 5 – the quattro drive with crown-gear differential and torque vectoring. With not one, but two innovative in-house developments, Audi continues to extend its lead over the competition. These innovative technologies were first showcased on the Audi RS 5 high-performance coupe. The Audi RS 4 Avant also employs this quattro drive concept. There are iTV programmes showcasing these technologies for the Audi RS 5 (3rd and 4th quarter 2010).Crown-gear differential – Torque vectoringThe crown-gear differential belongs – like its predecessor – to the category of limited slip centre differentials with asymmetricdynamic torque split. It surpasses its predecessor with its improved dynamic torque split – which gives better traction – and better integratibility with electronic brake control systems. Other strong points of the crown-gear differential are its compactness and low weight. At 4.8 kilograms, it is two kilograms lighter than the previous unit. The basic torque split is 60 percent to the rear axle and 40 percent to the front axle. In the dynamic operating range (asymmetricdynamic torque split), the differential distributes up to 85 of torque to the rear axle and up to 70 percent to the front axle.The illustration shows the Audi RS 5. 30 %20 %30 %20 %Sheet-metal case for encapsulation of the crown-gear differentialGearbox output shaft (output to rear axle, transmits torque to the prop shaft)Gearbox output shaft (output shaft from manual gearbox, transmits torque to the crown-gear differential)Output shaft with beveloid gear (input to front axle, transmits torque to the front axle final drive via the sideshaft)6617_003Torque vectoringAudi pairs the crown-gear differential with a torque vectoring system. This software, specially developed by Audi, is integrated in the ESC control unit. Torque vectoring is an evolutionary form of the electronic differential lock (EDL) as seen on front wheel drive models. A new feature is that each of the four wheels can be correctively braked. When cornering at high speeds, the ESC control unit determines the reduced load on the wheels on the inside of the curve and the increased load on the wheels on the outside of the curve. From this information, it can determine the possible drive power for each individual wheel with a relatively high degree of accuracy. Drive torque is transferred to the wheels on the outside of the curve by controlled braking intervention. The result is improved driving dynamics. The vehicle's response remains neutral for longer, i.e. understeer is largely prevented when turning into corners and accelerating, and the ESC system intervenes later – assuming it is even needed. For more information, please refer to page 24.617_004Rear axle final drive unit 0BF – sports differentialEveryone defines "driving" differently. Those who want to experience the full driving dynamics of the Audi RS 5 or the Audi RS 4 Avant, the sports differential is a good choice in addition to other optional systems designed for enhanced driving dynamics.Changing the ATF and axle oilRS models often have to withstand the harsh conditions of motor racing. In such cases, not only the components but also the oils are put under enormous stress. For that reason, special guidelines apply to RS models regarding servicing work and intervals. The following guidelines are currently valid for the sports differential on the Audi RS 5 and Audi RS 4 Avant: • The oil change interval for axle oil is every 60,000 km. • The ATF must be changed every 60,000 km or earlier if the time limit on the MTF temperature meter of 7-speed dual clutch gearbox 0B5 has expired. For more information, please refer to page 20 ff.617_005Reference For detailed information on the sports differential, please refer to Self Study Programme 476 "Rear axle final drive unit 0BF/0BE – Sports differential" and the relevant Audi Service TV programmes (there are currently four). Please refer to the current workshop literature for detailed information on the oil change intervals.7Crown-gear differentialCrown-gear differential – Design and functionBasically, the limited slip centre differential is a crown-gear differential comprising two crown gears and four cylindrical spur gears which transmit drive torque and act as differential gears. This configuration closely matches that of the bevel gear differential as used in the final drive of a gearbox. A special feature of this differential is that both crown gears have different reference diameters1). This provides the desired asymmetric torque split. The cylindrical differential gear shafts are mounted in bearings in the differential case. On the back of both crown gears there is a multi-plate clutch which meshes with the corresponding crown gear. The inner plates of both multi-plate clutches engage the crown gears while the outer plates engage the differential casing. Threaded rings act as the counter-bearings of the multi-plate clutches and close the crown-gear limited slip differential. The gearbox output torque is transferred to the differential case. Four shafts transmit the torque to the differential gears, which in turn transmit torque to both crown gears; one sends the torque to the front axle and the other to the rear axle. The displacement forces in the gearing travel through the crown gears to produce an axial force which acts on the multi-plate clutches. The multi-plate clutches produce the desired lock-up effect in the differential. Background To understand the power distribution scheme of the crown-gear limited slip differential, one must consider two effects – basic torque split and dynamic torque split. When driving, the dynamic torque split is always superimposed on the basic torque split. The crown-gear differential is designed in such a way that different amounts of drive power are transmitted to the differential outputs (front axle and rear axle). This is referred to as an "asymmetric torque split". An asymmetric limited slip centre differential is defined by four operating states: • • • • Maximum distribution to the front axle under throttle Maximum distribution to the front axle during overrun Maximum distribution to the rear axle under throttle Maximum distribution to the rear axle during overrunIn each of these four operating states, the differential has a different lock-up effect. The torque split in the above four operating states is defined at the design stage in order to provide the desired handling under throttle and during overrun.Locking pin Differential gear shaftInner plate Threaded ringOuter plate Crown gear – output to rear axle final drive unit Differential case (driven) Four differential gears Crown gear – output to front axle final drive unitThreaded ring1) The term "reference diameter" is used to describe the effective working diameter of a gear.617_006!8Information The manufacturer uses threaded rings to eliminate clutch backlash and set a defined amount of clutch torque. The threaded rings are secured by spot welds to prevent twisting and cannot be detached. The sheet-metal housing is also welded, which means that non-destructive opening of the crown gear is not possible.Asymmetric basic torque splitThe different reference diameters1) of the crown gears result in an asymmetric torque split. The number of teeth ratio is approximately 40 : 60, resulting in an asymmetric torque split of approximately 40 : 60 in favour of the rear axle. We refer to this torque split, which is defined by the geometry of the components, as the "asymmetric basic torque split". The different reference diameters result in different leverages; input torque is transmitted with a ratio of approximately 60 : 40. This means that approximately 40 % of total drive torque is sent to the front differential and approximately 60 % to the rear differential. The basic torque split is, in principle, effective in all operating states and is superimposed by the dynamic torque split. Together, they result in the asymmetric-dynamic torque split.617_007RA2) 60 %FA3) 40 %Larger reference diameter at crown gear output to rear axle final drive (RA2)) Meshing of FA3) crown gear Meshing of RA2) crown gearSmaller reference diameter at crown gear output to front axle final drive (FA3))Crown gear (FA3)) z 25617_008Crown gear (RA2)) z 35 More leverage = more torque (to rear axle) Differential gear Less leverage = less torque (to front axle)Gearbox output shaft (transmits torque to the prop shaft connecting to the rear axle final drive)Gearbox output shaft (output shaft from manual gearbox, transmits torque to the crown-gear differential) 40 %60 %100 %617_0092) 3) Rear axle Front axleOutput shaft with beveloid gear (input to front axle, transmits torque through the sideshaft to the front axle final drive)9Asymmetric-dynamic torque splitIn addition to the asymmetric basic torque split of approx. 40 : 60, a locking torque proportional to the drive torque is produced in the differential. This locking torque plus the basic torque split gives the possible torque distribution to both axles. Thus, the crown-gear differential locks up before any changes in traction between axles take effect. If an axle loses traction, drive torque is immediately diverted to the other axle within the allowable lock-up range and according to how much traction the wheels have. If the working range is exceeded, ESC intervention provides additional torque and, thus, forward thrust. Function As soon as torque is input into the crown-gear differential, an axial force occurs between the differential gears and the crown gears due to the tooth shape and the design of the differential. The tooth geometry gives rise to axial forces of differing magnitude at both crown gears. Both crown gears are thrust in an axial direction and close the clutch plates. Depending on the axial force, this produces a clutch torque which positively connects the crown gears with the differential case. This means that the clutch plate assembly is preloaded depending on the drive torque, thus producing a corresponding lock-up effect. The lock-up effect is defined by the lock-up value. The lock-up value describes the output torque differential at both outputs resulting from the lock-up effect of the differential.15 : 85 torque splitIf the front axle loses traction without yet exceeding the traction limit, the rear axle can transmit up to 85 % of drive torque. If the traction limit is exceeded, more slip occurs at the wheels on the front axle. When wheel slip exceeds a defined level, the ESC control system intervenes and provides additional torque. The additional torque, basic torque split and lock-up effect produce a corresponding drive torque at the rear axle.15 %85 %70 : 30 torque splitIf the rear axle loses traction without yet exceeding the traction limit, the front axle can transmit up to 70 % of drive torque. If the traction limit is exceeded, more slip occurs at the wheels on the rear axle. When wheel slip exceeds a defined level, the ESC control system intervenes and provides additional torque. The additional torque, basic torque split and lock-up effect produce a corresponding drive torque at the front axle.Axial forces617_01070 %30 %617_011 10Operating instructionsThe crown-gear limited slip differential operates fully independently, is maintenance-free and requires no input on the part of the driver. In conjunction with torque vectoring, the quattro drive offers drivers a high standard of driving dynamics, safety and comfort. Nevertheless, there are a few points to note regarding the quattro powertrain. • The crown-gear limited slip differential cannot be compared to a 100 % mechanical differential lock. If an axle or a wheel begins to spin, no drive will be available until the ESC has produced additional torque by brake intervention (EDL intervention). ESL does not intervene until it detects a defined engine speed differential and a corresponding engine torque. The driver must apply throttle selectively until ESC produces additional torque by brake intervention. The additional torque results in a drive torque at the tractive wheels. The crown-gear differential assists torque distribution in the way described above. To prevent the brake from overheating during heavy and prolonged ESL intervention, the EDL function is deactivated when the brake disc temperature exceeds a value computed by the ESC control unit. As soon as the brake has cooled down, the EDL function cuts in again automatically. • Continuous synchronisation of high differential rotation speeds between the front and rear axles coupled with high engine load is harmful to the crown-gear differential. • In the case of the Audi RS 5 and Audi RS 4 Avant, snow chains may only be fitted on certain rim-tyre combinations and only on the front axle. Please note the guidelines and specifications in the Owner's Manual and in the tyres/wheels catalogue. • If the prop shaft has been removed, there is no or only minimal drive because sufficient additional torque cannot be developed in the centre differential. • A performance test can/may only be performed on a four-wheel roller dynamometer. • A brake test can be safely performed on a low-speed test bench (max. 6 kph). Drive must be provided by the dynamometer. • The vehicle must not be towed with the front or rear axle elevated (refer to Owner's Manual).Towing If a vehicle with 0B5 gearbox needs towing, the conventional restrictions on automatic gearboxes apply: • Selector lever in position "N" • Max. towing speed 50 kph • Max. towing distance 50 kmReason: When the engine is at standstill, the oil pump is not driven and certain parts of the gearbox are not lubricated. Exceeding the max. towing speed of 50 kph results in unacceptably high rotational speeds in the gearbox and dual clutch because one gear is always engaged in both sub-gearboxes. If the towing conditions are ignored, serious gearbox damage can occur.Reference The working principle of the crown-gear differential is identical to that of the previous limited slip centre differential. For more information of a general nature, please refer to Self Study Programme 363 "Audi Q7 – Transmission / Distributor Gear 0AQ", page 18 ff.11Special features of the 0B5 gearboxSplined prop shaftThe innovative new prop shaft connector system was first used on the Audi A8 ’10. To fit the prop shaft on the gearbox, all that needs to be done is to slide on and secure the joint. This connector system is not only 0.6 kg lighter but also saves a considerable amount of time during assembly and dismantling. The spline connector will be adopted for all other gearboxes in the course of further development.Slot Gearbox output shaft with spline connectorClampSpring sleeveJoint (component part of the prop shaft)617_012!12Information The joint is an integral component of the prop shaft and cannot be replaced separately. The rubber boot can be replaced using a special tool.Design and functionThe spring sleeve is made of spring steel. On one side of the spring sleeve, there are spring elements with locking hooks. These locking hooks fix the spring sleeve in place in a slot in the joint hub. On the other side of the spring sleeve, there are angled spring elements. They snap into the slot in the shaft stump when fitting the prop shaft.Spring sleeve617_013When the prop shaft is dismantled, the spring sleeve is held inside the joint hub by the spring force of the spring elements. To make sure that the spring sleeve does not become detached from the joint hub, special attention must be given to correct positioning and fitting of the prop shaft. Once the shaft stump has passed the locking hooks during fitting, the locking hooks are fixed in place and cannot slide out of the slot.617_014Spring sleeveSlotClamp617_015During assembly, the joint must be pushed onto the gearbox output shaft until the spring sleeve engages the slot. The spring sleeve secures the spline in an axial direction. The spring sleeve is fixed in position by a clamp thereby securing the prop shaft in an axial direction. In addition, the joint is sealed.Reference For more information and instructions for assembly of the splined prop shaft, please refer to the Audi Service TV programme – "Audi A8 Power Transmission Part 2".13ATF filter (pressure filter)Vent for ATF oil systemEasy-change ATF filterThe 0B5 gearbox on models manufactured after 22/1010 (model year 2011) has a new ATF filter module with filter cartridge. The new ATF filter module is integrated in the ATF line fitting and includes a filter cartridge. The filter cartridge also has to be replaced when changing the ATF. The ATF filter (pressure filter) is now in the return line from the ATF cooler, and filters out impurities from the ATF cooler and from the lines. The new filter module has better filtration properties, as well as saving weight and space.ATF pipesFilter cartridge with differential pressure valveCover14Vent hose for manual gearbox oil system vent – gear oil (MTF)617_017ATF line filterOn models manufactured prior to 22/2010, the ATF filter (pressure filter) is integrated in the supply line to the ATF cooler. The filter does not have a fixed maintenance interval.617_016Connections for ATF linesReference For more information about the ATF filter module with filter cartridge, please refer to the Audi Service TV programme "7-speed Dual Clutch Gearbox 0B5: Servicing the ATF Filter".!Information Keep the filter cartridge away from water. Even small amounts of moisture can cause filter fleece to dissolve. The dissolved filter fleece will then get into the mechatronics unit and cause it to malfunction. There are various versions of the filter housing and the cover. Please read the information given in the ETKA and in the Workshop Manual.15Changing the MTFThe 0B5 gearbox on both RS models has to transmit up to 331 kW of engine power. If this power is demanded, the MTF1) can become very hot. The MTF contains special additives in order to withstand the stresses on the oil. These additives degrade at high temperatures and the oil loses its essential properties. This is why the MTF must be changed after it has been subjected to correspondingly high thermal loads, in order to avoid excessive wear or damage to the gearbox. To determine the thermal load on the MTF, the 0B5 gearbox in RS models has an MTF temperature monitoring function. In the case of the Audi RS 5 and Audi RS 4 Avant, the MTF currently has a general change interval of 30,000 km2). By comparison: The ATF must be changed every 60,000 km2). If the MTF temperature monitoring function determines a high thermal load on the MTF, the event memory entry "P0897 gear oil deterioration" is generated. In this case, it is necessary to change the MTF even if the vehicle has covered less than 30,000 km since the last MTF change.Resetting the temperature meters after changing the MTFAfter changing the MTF, it is important to reset the temperature meters of the temperature monitoring function. The "Reset temperature meter" function is available for this purpose on the diagnostic tester.Guided Functions Functions Select vehicle system or function 02 – Gearbox electronics 0B5 | J217Audi V18.25.00 23/09/2010 Audi A5 2008 2011 (B) Coupe CFSA 4.2l FSI / 331 kW 02 – Interrogate fault memory (Rep. Gr. 34) 02 – Clear fault memory (Rep. Gr. 34) 02 – Read measured values (Rep. Gr. 34) 02 – Identification services (Rep. Gr. 34) 02 – Encode contol unit (Rep. Gr. 34) 02 – Replace control unit/mechatronics (Rep. Gr. 34) 02 – Basic setting (Rep. Gr. 34) 02 – Reset temperature meter (G754) (Rep. Gr. 34) 02 – Check gear selection (Rep. Gr. 34) ** – Repair immobiliserOperating modeVehicle System testGo to617_018Audi V18.25.00 23/09/2010 Audi A5 2008 2011 (B) Coupe CFSA 4.2l FSI / 331 kWGuided Functions Function test Reset gear oil temperature meter Reset gear temperature meterThe following readings are currently available for gear oil temperature (not ATF): 151 °C – 161 °C: 0 minutes greater than 161 °C: 0 minutes The meters can be reset to their initial values by pushing the Ready button.FinishedAfter the function is started, the system displays two temperature ranges and the time in minutes the MTF temperature was within each temperature range. In this example, 0 minutes is displayed which means that the MTF temperature has not yet reached a critical level. The temperature meters for the lower temperature ranges are not displayed here. For more information, please refer to page 20. In the course of the menu, all temperature meters (including non-visible meters) are reset. The temperature meters are also referred to as temperature intervals.Guided Functions Function testOperat modeReset gear oil temperature meter Reset gear temperature meterAudi V18.25.00 23/09/2010 Audi A5 2008 Guided Functions 2011 (B) Function test Coupe CFSA 4.2l FSI / 331 kW Reset gear oil temperature meterFinishedAudi V18.25.00 23/09/2010 Audi A5 2008 2011 (B) Coupe CFSA 4.2l FSI / 331 kWThe meter for operation at elevated gear oil temperature was reset to factory default. - Turn off the ignition. The reset values are not permanently saved until the ignition has been turned off. - Push the Ready button straight after turning off the ignition.Reset gear temperature meterThe meter for operation at elevated gear oil temperature was reset to factory default. The following counts were set 151 °C – 161 °C: 0 minutes greater than 161 °C: 0 minutesFinishedOperating modeGo to Operating mode Go to617_0191) TF is the abbreviation for Manual Transmission Fluid and refers M to the gear oil for the purely mechanical part of the gearbox. The oil system of the 0B5 gearbox lubricates the gear set, the front axle final drive and the transfer box including the centre differential.2) he specifications in "Strict Maintenance Operations" and/or the T maintenance chart apply.16Oil systems – oil drain screwsMTF (Manual Transmission Fluid) ATF (Automatic Transmission Fluid)617_020617_021ATF drain screwMTF drain screw with gear oil temperature sensor 2 G754 (version 2), see next page!Information The sensor contacts can easily become exposed to MTF when draining the ATF. However, this should be avoided as the MTF contains phosphates and the contacts will corrode if they come into contact with MTF. If the sensor contacts are exposed to MTF, they must be thoroughly cleaned.17MTF temperature monitoring functionA special feature of the 0B5 gearbox in combination with the high-performance engines of the Audi RS 5 and/or the Audi RS 4 Avant is an MTF temperature monitoring function1) which uses a separate temperature sensor (gear oil temperature sensor 2 G754) and evaluates the measured data generated by this sensor. For more information on this system, please refer to MTF temperature collective, page 20 ff. MTF temperature monitoring is necessary for two reasons: 1. To determine the heat input into the MTF and hence the thermal ageing of the MTF (refer to Changing the MTF). 2. In the MTF oil system of the 0B5 gearbox there are plastic and electrical components, such as the gear sensor G676 and gearbox input speed sensors 1 and 2 (G632 and G612). These electrical and plastic components can become damaged and fail at excessively high temperatures. When defined temperature limits are exceeded, a so-called cooling function is activated in order to prevent the MTF temperature from rising any further. Event memory entries containing information on due servicing work (refer to page 16) are also generated.1) he 0B5 gearbox on the Audi S6 ’12 and Audi S7 Sportback is T also equipped with an MTF temperature monitoring system with gear oil temperature sensor 2 G754 (version 2).Gear oil temperature sensor 2 G754There are two versions of G754 and its installation location: Version 1: In the case of models manufactured prior to 2011, G754 is installed in the intermediate gearbox housing.Version 1617_038Version 2617_02218Version 2: In the case of models manufactured after 2011, G754 is integrated in the MTF drain screw. Gear oil temperature sensor 2 G754 consists of an NTC resistor. NTC stands for "Negative Temperatur Coefficient" and refers to a resistor (component) whose electrical resistance (ohm) decreases as the temperature rises (thermistor). Version 2617_039!Information In the case of version 2, note that the drain screw may drop into the oil or the contacts of G754 may come into contact with the MTF when changing the MTF (with G754). The MTF contains substances which can cause the contacts of G754 to corrode thereby falsifying the measured data. If the contacts of G754 (or the connector) have come into contact with MTF, they must be thoroughly cleaned and dried before reconnecting the connector.Measured value – MTF temperatureTo read out the MTF temperature, the program "G754 – Gear oil temperature sensor 2, temperature" is available in the function/ component selection menu. For better assessment of the measurement results, three temperatures are displayed in this program. No extreme deviations should normally occur between the three temperature values. The values should be mutually plausible. For example, it is not plausible for an MTF temperature of 80 °C to be displayed at the same time as an ATF temperature of 25 °C.Guided Fault Finding Function/component selection Select function or componentAudi V18.25.01 06/10/2010 Audi A5 2008 2011 (B) Coupe CFSA 4.2l FSI / 331 kW+ Drive (Rep. Gr. 10 – 39) + 7-speed dual clutch gearbox 0B5 (S tronic) + 01 – Self-diagnosable systems + 02 – Gearbox electronics 0B5 | J217 + 02 – Sublsystems, boundary conditions J217 – Gearbox control unit, supply voltage (Rep. Gr. 34) J217 – Gearbox control unit, J533, communication (Rep. Gr. 34) J217 – Databus, implausible messages (Rep. Gr. 34) J217 – Gearbox control unit, pressure build-up (Rep. Gr. 34) J217 – Gearbox control unit, temperature (Rep. Gr. 34) G754 – Gear oil temperature sensor 2, temperature (Rep. Gr. 35) J217 – Signal for starter lock -P/N- (Rep. Gr. 34) J217 – Limited functionality due to engine (Rep. Gr. 34) J217 – Automatic gearbox control unit, wrong software versionOperating mode Go to617_023Guided Fault Finding Function testThe gear oil in the gear set is the MTF (MTF temperature).Check gear of temperature of gear set Check temperature valuesAudi V18.25.01 23/09/2010 Audi A5 2008 2011 (B) Coupe CFSA 4.2l FSI / 331 kWThis ATF temperature is a value which is calculated by the gearbox control unit. It is calculated from the signals generated by the clutch temperature sensor G509 and by the temperature sensor in control unit G510. G510 is located directly on the PCB in the automatic gearbox control unit J217 (chip temperature).The following oil temperatures are measured: ● Gear oil in gear set (manual gearbox) via G754: 22 °C ● ATF in the mechatronics (calculated): 26 °C ● ATF of the clutches via G509: 31 °C - Let the engine idle and monitor the measured data. To cancel, push the • button1. Installation locationThe measured value generated by G509 is the ATF temperature of the cooling oil ejected from the dual clutches.Operating modeGo to617_024Reference For more information on the ATF temperature sensors, refer to Self Study Programme 429 "Audi Q5 – Units".19MTF temperature collectiveThe gearbox control unit for the Audi RS 5 and the Audi RS 4 Avant has an additional software-based MTF temperature monitoring function. The MTF temperature monitoring function records and evaluates all measured values generated by gear oil temperature sender 2 G754. These measured values are evaluated statistically in an MTF temperature collective. Five temperature ranges assigned to so-called temperature intervals are defined for the purposes of evaluation. Each temperature interval has an elapsed-time meter which records the time the MTF temperature was in each temperature range. This gives a good indication of the extent to which the MTF and the components have been subjected to thermal load and/or stress. Temperature intervals TEMP_INTERVAL_01 TEMP_INTERVAL_02 TEMP_INTERVAL_03 TEMP_INTERVAL_04 TEMP_INTERVAL_05 –60 °C – 120 °C 121 °C – 130 °C 131 °C – 150 °C 151 °C – 161 °C 162 °CTemperature intervalsThe temperature intervals are displayed in the vehicle self-diagnostics for the measured values "Meter for operation at elevated gear oil temperature" and "Excess temperature meter".Vehicle self-diagnostics 011 – Measured data 02 – Gearbox electronics EV_TCMDL501021_001 Version: 001015Last name Meter for operation at elevated gear oil temperatureValueIn this example, the MTF temperature was within temperature range 1 between –60 °C and 120 °C for 300 hours, 3 minutes and 16 seconds and within temperature range 2 between 121 °C and 130 °C for 14 minutes and 58 seconds. The gearbox temperature has not exceeded 130 °C since the last time the temperature intervals were reset (refer to Resetting the temperature meter on page 16).Vehicle self-diagnostics 011 – Measured data02 – Gearbox electronics EV_TCMDL501021_001 Version: 001015617_025Temperature intervals 04 and 05 are important for temperature monitoring. A time limit is defined for each of these temperature intervals. The time limits are 2 hours for temperature interval 04 and 10 minutes for temperature interval 05. If the time limit for either of these temperature intervals is exceeded, the event memory entry "Gear oil deterioration" is generated in the gearbox control unit. No message or warning is issued via the instrument cluster. If this event memory entry is generated, it is necessary to change the MTF. Don't forget! The temperature meters (temperature intervals) must be reset after changing the MTF (refer to page 16).Last nameValue151 °C – 161 °Cmax. 2 hours162 ℃max. 10 minutes617_026If the event memory entry "Gear oil deterioration" is generated, the cooling function becomes active when an MTF temperature of 151 °C is exceeded (instead of 163 °C), refer to page 21.20Cooling functionIf the MTF temperature reaches critical levels, it must be reduced or prevented from increasing any further. The gearbox control unit initiates countermeasures, which are referred to herein as the "cooling function". When the cooling function is active, the vehicle's maximum speed is decreased in order to reduce heat input into the MTF.This is how the cooling function works: If an MTF temperature of 163 °C is exceeded, the maximum travel speed (V max.) is initially reduced by 20 kph. This corrective adjustment is made by reducing the engine power output when the speed limit threshold is reached. The vehicle's speed is gradually reduced in increments of 1 kph per second (20 kph in 20 seconds). The following example shows how the cooling function works: A vehicle is travelling at 260 kph and the MTF temperature exceeds 163 °C. V max. is now limited to 240 kph as described above. The MTF temperature is monitored at two-minute intervals and should decrease by at least 2 °C within these two minutes. If this is not the case, V max. is reduced by a further 20 kph. In this example, V max. is 220 kph. If the MTF temperature decreases by more than 2 °C within two minutes, the actual speed limit threshold is initially maintained. The temperature is monitored at two-minute intervals. At the end of the two-minute cycle, the system decides whether to further reduce or maintain the vehicle's current speed. When the MTF temperature drops below approx. 147 °C, the limit on maximum speed is canceled again. V max. is only limited down to a speed of 210 kph (lowest speed reduction threshold). If the cooling function is active, the event memory entry "P06AA – Internal temperature sensor 2, temperature too high" is generated. No fault message is displayed in the instrument cluster. Drivers will normally notice the restrictions on maximum speed and contact their service partner. Possible complaint: no power at times, vehicle is not achieving V max. or similar descriptions. If the event memory contains the above-mentioned entry, it is the task of the service partner to check the following points and explain the cooling function to the driver. A distinction is made between two cases: Case 1: Temperature interval 04 or 05 has been utilised by less than 50 % (refer to page 20). In this case, all that need be done is clear the event memory and explain the cooling function to the driver. Case 2: Temperature interval 04 or 05 has been utilised by more than 50 %. In addition to informing the driver and clearing the event memory, it is recommended that the MTF be changed. The next point to clarify is whether it make sense to change the MTF immediately? If the 30,000 km MTF change interval or another service event is due anyway, the MTF can also be changed at this time.Safety functionIf the MTF temperature continues to increase despite the fact that the cooling function is active and exceeds 180 °C for more than 30 seconds, the event memory entry "P0218 Maximal gear oil temperature exceeded" is generated. The yellow gearbox icon and the fault message "Gearbox malfunction: you can continue driving (limited functionality)" appear in the instrument cluster. In this case, a thermal overload has occurred rendering the MTF unusable. It must also be assumed that the electrical gearbox components and plastic parts have been damaged. In the case, the gearbox must be replaced.Gearbox malfunction: you can continue driving (limited functionality)617_03021Selector mechanismThe operating logic of the selector for the sport program (speed S) has been reconfigured. To shift from D to S (or from S to D), the selector is flicked back out of D once only. The selector always springs back to the D/S position. The shift schematic has has been adapted to the new operating logic. Advantages for the customer: • In the case of models equipped with Audi drive select, the S program can now be selected irrespective of the mode selected in Audi drive select. • tiptronic mode can now also be selected in the S programThe shift schematic with gearshift indicator is integrated in the console trim frame. The display unit Y26 is installed from below as a separate component.617_037Reference For more information about the selector mechanism, please refer to Self Study Programme 409 "Audi A4 ’08", page 34 ff.2223Torque vectoringIntroductionTorque vectoring provides improved traction when cornering and thereby enhances driving dynamics noticeably. Torque vectoring is a software function in the ESC control unit. It is an evolution of the electronic differential lock for front-wheeldrive models. In the case of the quattro powetrain, torque vectoring allows torque-controlling braking intervention at all four wheels.Background The principles of driving dynamics dictate that the maximum drive torque MA transmissible to the wheels on the outside of the curve increases with increasing transverse acceleration ay, while the maximum drive torque transmissible to the wheels on the inside of the curve decreases by the same amount. The adjacent diagram illustrates this behaviour. This is caused by the effect of centrifugal force, which acts at the vehicle's centre of gravity with its line of action running towards the outside of the bend. This produces what is known as roll torque, which is stabilised by the wheels. This roll torque reduces the load on the inside wheels and increases the load on the outside wheels. It follows that the wheels on the inside of the curve cannot transmit as much torque as the wheels on the outside of the curve.MA Transmissible drive torque as a function of transverse acceleration Mwheel on outside of curveMwheel on inside of curveay617_029Centrifugal forceTorque/roll torqueWeight force on outside of curveWeight force on inside of curve617_031The open axle differentials always distribute drive torque to both wheels of an axle at a ratio of approximately 1 : 1 (refer to Figure 617_033). If the maximum drive torque transmissible to the wheel on the inside of the curve decreases while cornering, only the same amount of torque is transmissible to the wheel on the outside of the curve even if the higher effective load on this wheel would allow a much higher drive torque. The wheel on the inside of the curve dictates how much drive torque is transmissible. If loss of drive torque occurs at the wheel on the inside of the curve, the flow of drive torque through the driveline will be interrupted.617_033 24Working principle and functionAdditional torque is developed by controlled braking of the wheels on the inside of the curve. In this way, additional drive torque is transferred to the wheels on the outside of the curve. The system reacts to changes in wheel load, and not to wheel slip. It is active during cornering and intervenes before a state of critical slip occurs at the wheels. The system calculates the reduction in load on the wheels on the inside of the curve, and the increase in load on the wheels on the outside of the curve while cornering. This calculation is based mainly on the measured data generated by the steering angle and transverse acceleration senders. From this, the ESC control unit determines the braking pressure required for the wheels on the inside of the curve. The required braking pressure is relatively low at approx. 5 bar – 15 bar, minimising brake load. Torque vectoring provides a high level of driving dynamics while at the same time minimising system complexity and providing excellent ride comfort.MAMA max on outside of curve1.)2.)3.) MA max on inside of curveay617_032Drive torque on inside of curve Drive torque on outside of curve Braking torqueMA MA max ay Drive torque Max. transmissible drive torque Transverse acceleration1.) Cornering without braking intervention As the amount of transmissible drive torque is dependent on the wheels on the inside of the curve, the amount of torque transmissible to the wheels on the outside of the curve cannot exceed this value.2.) and 3.) Cornering with braking intervention Braking torque is developed at the wheels under reduced load on the inside of the curve by active braking intervention. This braking torque acts as an additional torque and thus increases the total torque transmitted to the wheels on the inside of the curve, because more drive torque is needed in order to overcome the braking torque. It follows that higher drive torque can also be applied to the wheels on the outside of the curve. This torque is equal in magnitude to the total torque transmitted to the wheels on the inside of the curve.25Straight-line drivingWheel load and drive torque are evenly distributed on both sides.617_007617_034Cornering under loadThe wheel load shifts towards the outside of the curve due to the action of centrifugal force.If the ESC system intervenes with corrective braking (front and rear on the inside of the curve), this prevents the wheels on the inside of the curve from spinning and insures against "loss" of drive torque. Traction is maintained on the outside of the curve and drive torque is transferred to the wheels on the outside of the curve through corrective braking.Greater traction on the outside of the curveLess traction on the inside of the curve617_00426baYaw torque617_035The higher drive torque on the outside wheels results in additional torque about the vehicle's vertical axis (yaw torque). This yaw torque has the effect of steering the vehicle into the curve. The vehicle thus achieves higher cornering speeds and is provided with precise, agile and more pinpoint handling (driving dynamics). The result is a noticeable improvement in driving dynamics.a) If the system intervenes with corrective action, the vehicle travels the curve radius with less steering lock than would be the case without corrective intervention.b) If no corrective action is taken by the system, the vehicle travels the curve radius under the same conditions and at the same steering angle as in a). This means that more steering lock would have to be applied to negotiate the corner at the same speed. A condition is that this is physically possible within the given constraints.!Information Torque vectoring is always engaged if required and cannot be deactivated by the driver. Torque vectoring is not activated on road surfaces with very low coefficients of friction. In the case of vehicles with rear axle final drive unit 0BC (the standard final drive) torque vectoring is engaged on the front and rear axles. In the case of vehicles with rear axle final drive unit 0BF (sports differential), torque vectoring is engaged on the front axle only.27AnnexTest your knowledge1. How is the desired asymmetric torque split achieved in the crown-gear differential?□ □ □a) Through the axial offset of the crown gears utilising the leverage relative to the differential gears. b) Through the different reference diameters and resulting different leverages. c) Through the four fitted differential gears and their different leverages relative to the crown gears.2. What is the position of the inner plates of the multi-plate clutch in the crown-gear differential, and how are they connected to the gearbox?□ □ □a) They are positioned on the crown gear and positively connected to the latter. b) They are positioned on the differential case and positively connected to the latter. c) They are positioned on the differential gears and positively connected to the latter.3. What are the points to note when towing vehicles with an 0B5 gearbox?□ □ □a) Put the vehicle into gear so that the engine turns, driving the oil pump and lubricating certain parts of the gearbox. b) The vehicle may only be towed if the front or rear axle is elevated. c) Move the selector lever into the N position. Max. towing speed is 50 kph and max. towing distance is 50 km.4. What is the task of the spring sleeve when fitting the splined prop shaft?□ □ □a) The spring sleeve secures the spline in a radial direction. b) The spring sleeve secures the spline in an axial direction. c) The spring sleeve guides the prop shaft and otherwise has no function.5. What are the points to note when fitting the splined prop shaft in connection with the spring sleeve?□ □ □a) There are no special points to note because the spring sleeve is held in place on the joint hub by its spring elements. b) The spring sleeve must be fixed in place on the shaft stump before fitting the prop shaft. c) The prop shaft must be carefully positioned and mounted.6. Which of these statements is true of the torque vectoring system?□ □ □ □a) The system reacts to changes in wheel load, and not to wheel slip. b) The system reacts to wheel slip, and not to changes in wheel load. a) Additional torque is developed by controlled braking of the wheels on the outside of the curve. d) The ESC control unit sets a braking pressure of 5 bar – 15 bar at the wheels on the inside of the curve.7. What effect does torque vectoring have?□ □ □a) It produces an additional torque about the vehicle's vertical axis. This torque has the effect of steering the vehicle into the curve. b) The vehicle achieves a higher cornering speed. c) The vehicle is provided with agile, pinpoint and precise handling.288. Why is MTF temperature monitoring necessary?□ □ □a) To determine the heat input into the MTF. b) To be able to activate a cooling function if defined temperature limits are exceeded. c) To identify mechanical ageing of the MTF.9. Which of the following assemblies is integrated in the MTF oil system of the 0B5 gearbox?□ □ □a) Mechatronics b) Gear set c) Clutches10. A customer brings in a vehicle because the "Gearbox malfunction: you can continue driving (limited functionality)" warning lamp in the instrument cluster is lit. The diagnostic tester shows the entry "P0218 Maximum gear oil temperature exceeded". What are the steps to take?□ □ □a) The MTF temperature was between 131 and 150 °C. The MTF must be changed and the event memory cleared. b) The cooling function must be explained to the customer and the event memory cleared. c) Thermal overloading renders the MTF unusable, as well as damaging the electrical and plastic gearbox components. The complete gearbox must be replaced.11. What effects does the activated cooling function have?□ □ □a) Maximum vehicle speed is reduced. b) Heat input into the MTF is reduced. c) Engine power output is maintained.12. How is an asymmetric-dynamic torque split produced in the crown-gear differential?□ □ □a) The asymmetric basic torque split and the dynamic torque split cancel each other out. b) The asymmetric-dynamic torque split is a result of friction between the differential gears and the crown gears. c) In addition to the asymmetric basic torque split, a lock-up effect proportional to the drive torque is created by the multi-plate clutch.13. By which operating states is an asymmetric limited slip centre differential defined?□ □ □ □a) Maximum distribution to the front axle under throttle. b) Minimum distribution to the front axle during overrun. c) Minimum distribution to the rear axle under throttle. d) Maximum distribution to the rear axle during overrun.Test solutions: 1 b; 2 a; 3 c: 4 b; 5 c; 6 a,d; 7 a,b,c; 8 a,b; 9 b; 10 c; 11 a,b; 12 c; 13 a,d293031All rights reserved. Technical specifications are subject to change. Copyright AUDI AG I/VK-35 service.training@audi.de AUDI AG D-85045 Ingolstadt Technical status 10/12 Printed in Germany A14.5S01.03.20617Audi Vorsprung durch Technik