TECHNICAL DOCUMENTATION
SSP 627 Audi A3 Sportback e-tron (Type 8V)

This PDF is currently unavailable.
Read document text
Self Study Programme 627 For internal use onlyAudi A3 Sportback e-tron(Type 8V)Audi Service Training BackThe Audi A3 Sportback e-tron is a plug-in hybrid engineered to provide a fully integrated mobility solution. There is no need for drivers to change their driving habits because the Audi A3 Sportback e-tron is designed to allow simple use of e-mobility. It has an all-electric driving range of up to 50 kilometres and is driven by a 75 kW (102 HP) electric motor with a top speed of 130 kph. At high speeds and under heavy acceleration, the internal combustion engine is automatically activated to provide additional power.Forwards Ξ ContentsThe Audi A3 Sportback e-tron brings together the best of both worlds - an electric motor for emission-free driving and an economical internal combustion engine for long range. It therefore combines both driving enjoyment and environmental awareness.627_0422ContentsIntroductionVehicle distinguishing features _____________________________________________________________________________________________________________________________ 4 In brief ________________________________________________________________________________________________________________________________________________________ 6Safety instructionsElectrical safety rules ________________________________________________________________________________________________________________________________________ 8 Warning signs ________________________________________________________________________________________________________________________________________________ 9Drive unitSpecifications _ _______________________________________________________________________________________________________________________________________________ 10 Internal combustion engine _______________________________________________________________________________________________________________________________ 12 Fuel system __________________________________________________________________________________________________________________________________________________ 13Power transmissionOverview _____________________________________________________________________________________________________________________________________________________ 14 Gearbox modules _ __________________________________________________________________________________________________________________________________________ 16SuspensionOverview _____________________________________________________________________________________________________________________________________________________ 20 Electro-mechanical brake servo _ __________________________________________________________________________________________________________________________ 22 Brake system pressure accumulator VX70 _______________________________________________________________________________________________________________ 24High-voltage batteryOverview of hybrid components ___________________________________________________________________________________________________________________________ 26 Hybrid battery unit AX1 ____________________________________________________________________________________________________________________________________ 28 Electric drive power and control electronics module JX1 _______________________________________________________________________________________________ 32 Charging _____________________________________________________________________________________________________________________________________________________ 34 High-voltage lines _ __________________________________________________________________________________________________________________________________________ 39 Electrical AC compressor V470 ____________________________________________________________________________________________________________________________ 40 High-voltage heater (PTC) Z115 ___________________________________________________________________________________________________________________________ 40 Maintenance connector TW ________________________________________________________________________________________________________________________________ 41 Hybrid manager _____________________________________________________________________________________________________________________________________________ 42Air conditioningCooling systems, air conditioning and thermal management __________________________________________________________________________________________ 44 Stationary air conditioning _________________________________________________________________________________________________________________________________ 53InfotainmentOverview of versions ________________________________________________________________________________________________________________________________________ 54 Audi connect (depending on market) _____________________________________________________________________________________________________________________ 56 Audi connect e-tron services (depending on market) ___________________________________________________________________________________________________ 56 Audi connect (depending on market) _____________________________________________________________________________________________________________________ 56 Control unit for emergency call module and communication unit J949 _ ______________________________________________________________________________ 57Displays and controlsExterior sound _______________________________________________________________________________________________________________________________________________ 60 Electric drive button E656 _________________________________________________________________________________________________________________________________ 60 Display elements for driving in hybrid mode _____________________________________________________________________________________________________________ 61ServiceInspection and maintenance _ ______________________________________________________________________________________________________________________________ 64 Special tools and workshop equipment _ __________________________________________________________________________________________________________________ 66AnnexTest your knowledge ________________________________________________________________________________________________________________________________________ 68 Self Study Programmes ____________________________________________________________________________________________________________________________________ 70The Self Study Programme teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a Repair Manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. This content is not updated. For further information on maintenance and repair work, always refer to the current technical literature.InformationReference3 BackForwards Ξ ContentsIntroductionVehicle distinguishing featuresMMI system with e-tron displays e-tron logo on the dash panel (front passenger side) Switch for EV modee-tron logo on the design cover in the engine baye-tron specific single-frame radiator grille in chrome/matte blacke-tron specific front bumper with 2 aluminium-look clips on the air intake coverse-tron logo on the wingse-tron logo on the selector le4 BackForwards Ξ ContentsDash panel insert with power meter and e-tron displayse-tron logo on the boot lide-tron specific rear bumper with diffusor and aluminiumlook clips and concealed exhaust tail pipese-tron light alloy wheel (17" for Ambiente, 18" for Ambition)627_002evere-tron logo on the door sillsS line sills5 BackForwards Ξ ContentsIn briefDimensions14249551542 17851516 1966627_020987 39578712630 4312811627_0216675 BackForwards Ξ Contents14532139211422213441764 1000627_022Interior dimensionsFront cabin width in mm Rear cabin width in mm Front headroom in mm Rear headroom in mm Through-loading width in mm Load sill height in mm Boot capacity in l 13921)/14532) 13441)/14222) 9873) 957 1000 675 280/12204)Other specificationsConcept Battery type Total capacity in kWh Top speed in electric-only mode in kph Top speed in kph Acceleration 0 – 60 kph in electriconly mode in s Acceleration 0 – 100 kph in s Range (electric drive only) in km 4312 17855)Plug-in hybrid (PHEV) Lithium-ion system 8.8 130 222 4.9 7.6 up to 50 up to 940 0.32 2.13 40Exterior dimensions and weightsLength in mm Width in mm Width in mm Height in mm Front track width in mm Rear track width in mm Wheelbase in mm Kerb weight in kg Gross vehicle weight in kgTotal range in km Drag coefficient cw Frontal area in m2 Capacity of fuel tank in l19666) 1424 1542 1516 2630 1540 2050Shoulder room width Elbow room width 3) Maximum headroom 4) With rear backrest folded down 5) Excluding mirror 6) Including mirror1) 2)All dimensions are given in millimetres and refer to the unladen weight of the vehicle.7 BackForwards Ξ ContentsSafety instructionsElectrical safety rulesThe following five safety rules must always be observed and followed whenever performing work on the high-voltage system. This work may only be performed by qualified persons. This also applies to the qualified person responsible for the automotive high voltage systems: the high-voltage technician. These safety rules must be applied in the given order before commencing work on electrical systems.1. The following steps must be taken by the high-voltage technician.De-energise the vehicle Secure system against re-starting Check that no voltage is present2. 3. 4. These steps are not relevant to high-voltage vehicles.Earth and short-circuit vehicle Cover or block off adjacent live parts.5. !8Information Even AC voltages of 25 volts and DC voltages of 60 volts are hazardous to humans. It is, therefore, important to follow the safety instructions given in the Service Literature and in the Guided Fault Finding routine, as well as the warnings displayed on the vehicle.!Information Work on the high-voltage system may only be performed by a qualified high-voltage technician. BackForwards Ξ ContentsWarning signsTo minimise the risk associated with the high-voltage system for users, service and repair shop personnel, as well as for technical and medical emergency responders, there are several warning and information labels attached to the Audi Q5 hybrid quattro. Basically, two types of warning label are used: • Yellow warning label with warning symbol for electrical voltage • Warning label marked "Danger" against a red backgroundThe following yellow warning labels are used to identify high voltage conducting components or high-voltage components installed in the immediate vicinity or, for example, hazardous components concealed by covers.Warning against a hazardous area according to DIN 4844-2 (BGV A8) Warning against touching live partsWarning against hazardous electrical voltage according to DIN 4844-2 (BGV A8)627_004627_005Warning against hazardous electrical voltage according to DIN 4844-2 (BGV A8)Mandatory signs: Observe instructions for use according to DIN 4844-2 (BGV A8)The warning labels marked "Danger" identify high-voltage components or high voltage conducting components.627_006 627_007Warning against hazardous electrical voltage according to DIN 4844-2 (BGV A8)Warning against touching live partsMandatory signs: Observe instructions for use according to DIN 4844-2 (BGV A8)Special high voltage battery identification label This adhesive label is affixed to the top of the high-voltage battery, both in English and in the import country's national language.9 BackForwards Ξ ContentsDrive unitSpecificationsTorque-power curveEA211 series 1.4l TFSI engine with engine code CUKBPower in kW Internal combustion engine Electric motor System (15 sec.)Torque in Nm Internal combustion engine Electric motor System (15 sec.)627_093Engine speed [rpm]10 BackForwards Ξ ContentsInternal combustion engine and electric motor with gearboxHybrid module with electric drive motor V1416-speed dual clutch gearbox (S tronic)1.4l TFSI engine627_107Features Engine code Type Internal combustion engine output in kW at RPM Electric motor output in kW at RPM System output in kW Torque of int. combustion engine in Nm at RPM Electric motor torque in Nm at RPM System torque in Nm Displacement in cm3 Stroke in mm Bore in mm Number of valves per cylinder Firing order Compression ratio Fuel type Turbocharging Engine management system Powertrain type Lambda control Mixture formation Emission standard Combined fuel consumption in l/100 km Combined CO2 emission in g/km Combined electrical power consumption in kWh/100 kmSpecifications CUKB Four-cylinder in-line engine 110 at 5000 - 6000 75 at 2000 - 2300 150 250 at 1600 - 3500 330 to 2200 350 1395 80 74.5 4 1–3–4–2 10 : 1 Premium unleaded 95 RON Exhaust turbocharger Bosch MED 17.01.21 6-speed dual clutch gearbox (S tronic) 1 sensor upstream of catalytic converter and 1 sensor downstream of catalytic converter Direct injection EU 6 1.5 351) 14.31)acc. to ECE standard11 BackForwards Ξ ContentsInternal combustion engineThe Audi A3 Sportback e-tron has an EA211 series 1.4l TFSI engine developing 110 kW. Given that the gearbox is 57.5 mm longer to accommodate the e-machine, the engine is mounted this amount further to the right. The Audi A3 Sportback e-tron can be driven in electric-only mode for a lengthy period of time, resulting in long phases during which the internal combustion engine is not in use. The main bearings, big-end bearings and piston rings have a special coating. In addition, piston backlash has been adapted and the cylinder liners are plasma-coated. During electric-only driving, the internal combustion engine can be started in order to heat up the catalytic converter. To allow wear-free starting in electric-only mode, the internal combustion engine can be cranked by closing clutch K0 so as to ensure that enough oil is available for restarting. For some countries, the internal combustion engine comes equipped with a secondary air system.627_023Engine startThe internal combustion engine is started by the e-machine. The engine control unit J623 sends a start message to the dual clutch gearbox mechatronic unit J743. Clutch K0 is closed and connects the e-machine's rotor to the internal combustion engine's crankshaft. The rotor begins to rotate and brings the crankshaft up to starting speed. The engine control unit J623 enables ignition and fuel injection, and the internal combustion engine starts up. If it is neccesary to start the internal combustion engine when the vehicle is running in electric-only mode, the torque from the e-machine is increased by the amount necessary to start the internal combustion engine when the clutch closes. This prevents judder. After starting, the clutch K0 is opened and the internal combustion engine runs at no load. After the speed of the internal combustion engine has been adapted to that of the e-machine, the clutch K0 is closed.Reference For further information about the function and design of the basic engine, refer to Self Study Programme 616 "Audi 1.2l and 1.4l TFSI engines of the EA211 series".12 BackForwards Ξ ContentsFuel systemSince hydrocarbons also form in electric-only mode, there is the danger of overloading the activated charcoal filter, with the result that the hydrocarbons can no longer be bound. The Audi A3 Sportback e-tron is, therefore, fitted with a pressure reservoir. During electric-only driving, the line leading to the activated charcoal filter is closed by closing the fuel tank shutoff valve N288. The pressure inside the fuel tank thereby increases to approx. 0.3 bar and is indicated to the engine control unit by the fuel tank sensor G400.Fuel tank shutoff valve N288 Tank pressure sensor G400627_094Filler flapThe filler flap is permanently locked and cannot be opened by hand. The filler flap cannot be opened until the pressure inside the fuel tank has dropped. If the driver has actuated the fuel filler flap release button E319, the engine control unit opens the fuel tank shutoff valve N288. The reduction in pressure is detected by the fuel tank pressure sensor G400. The fuel filler flap is then opened automatically by the onboard power supply control unit J519. The status of the fuel filler flap is indicated in the dash panel insert.627_095Tank system: is being vented. Please waitTank system: Now fill tankP+9.5 °CP+9.5 °C627_096627_097 13 BackForwards Ξ ContentsPower transmissionOverviewPower transmission in the Audi A3 Sportback e-tron is provided by the transversally mounted 6-speed dual clutch gearbox 0DD for front-wheel drive. The integrated electric drive motor V141 is a permanently excited synchronous machine and develops up to 75 kW of power. It is capable of delivering up to 330 Nm of torque to the gearbox. The electric drive provides electric-only driveaway and driving as well as starting the internal combustion engine via clutch K0 (refer to page 18). If necessary, in Boost mode, the electric drive and internal combustion engine are connected via clutch K0 and deliver the maximum system power to the gearbox. In generator mode, the electric drive motor V141 is driven by the internal combustion engine using the vehicle's propulsion energy (recuperation) or through the closed clutch K0. The electric drive motor thus supplies power to the entire vehicle. Clutches K1 and K2 (refer to page 18) transfer the entire power generated by both drives to sub-gearboxes 1 and 2. All 3 of clutches K0, K1 and K2 are wet-type clutches and are controlled by the gearbox's mechatronic unit. The gearbox has only one ATF supply. The approx. 7 litres of ATF supply both the gearbox hydraulics and the sub-gearbox. Both sub-gearboxes form the manual gearbox.2-pin connector for safety line10-pin connector for: 2 contacts for the drive motor temperature sensor G712, 6 contacts for rotor position sensor 1 of the drive motor G713 and 2 contacts for the safety lineParking lock leverOil gauge pipe627_103ATF drain screw 1 (manual gearbox)14ATF inspection screw BackThe 6 forward gears of the manual gearbox provide a ratio spread of 6.8. The mechatronic unit is located below the housing cover named after it. The mechatronic area is separated from the manual gearbox by a bulkhead. During vehicle operation, the mechatronic unit is flooded up to the overflow port by the bulkhead (refer to page 17). The mechatronic unit, clutches, gear selectors and manual gearbox are supplied on demand by an electrically driven ATF hydraulic pump. A hydraulic pressure accumulator serves as an ATF reservoir.Forwards Ξ ContentsThe 6-speed dual clutch gearbox 0DD is integrated into the vehicle's thermal management system. The gearbox facilitates the start-stop system. In addition, the mechatronic unit for the dual clutch gearbox J743 is integrated into the immobiliser system.P6 (W)1)Gearbox ventCoolant supplyATF pressure filterScrew plug for mechatronic unit filler port Housing cover for mechatronic unitP5 (V)1)P4 (U)1)ATF coolerCoolant return627_104Coolant return line for cooling the electric drive motor V141Coolant supply for cooling the electric drive motor V1412-pin connector for mechatronic unit power supply10-pin connector (for transmitting data to/ from the mechatronic unit)1)P4 (U), P5 (V), P6 (W) are high-voltage lines running from the electric drive power and control electronics JX1 to the electric drive motor V141.15 BackForwards Ξ ContentsGearbox modulesThe 6-speed dual clutch gearbox 0DD consist of the hybrid module, the manual gearbox and the mechatronic unit. Drive motor rotor position sensor 1 G713 and drive motor temperature sender G712 are located on the hybrid module. Both senders supply their data to the electric drive power and control electronic JX1.Hybrid moduleP4 (U)P5 (V)P6 (W)Manual gearboxDrive motor rotor position sensor 1 G713Drive motor temperature sensor G712Housing cover for mechatronic unit ATF drain screw 2 (mechatronic unit) Hydraulic pump motor V401 with rotor position sensorFrom ATF intake filter, located in sump of manual gearbox!16Information Before removing the gearbox or the mechatronic unit, it must be ensured that the ATF pressure accumulator is depressurised and that the hydraulic pump is disabled by running a suitable routine on the diagnostic tester. If the ATF, the gearbox or the mechatronic unit is replaced, it must be ensured that the ATF level has been set correctly, as detailed in the workshop manual, and that the mechatronic unit is flooded with ATF before starting up. This prevents the high-pressure pump from running dry. The mechatronic unit and the immobiliser must be programmed by the diagnostic tester using the Replace mechatronic unit function. BackForwards Ξ ContentsMechatronic unit for dual-clutch gearbox J743Apart from the gear selector and clutch slave cylinder, the mechatronic unit accommodates all sensors and actuators of the gearbox control unit. These includes the valves, the pump motor, the pressure and temperature senders, the distance and speed sensors. Main pressure valve and pressure relief valves • Main pressure valve N472 (accumulator filling valve, allows controlled evacuation of the pressure accumulator) • Automatic gearbox pressure control valve 3 N217 (pressure relief valve, sub-gearbox 1) • Automatic gearbox pressure control valve 4 N218 (pressure relief valve 2, sub-gearbox 2) During operation, the mechatronic unit is flooded up to the ATF overflow port. This volume does not drain off via the ATF drain screw 1. ATF drain screw 2 must be removed for this purpose.Clutch valve • Automatic gearbox pressure control valve 1 N215 (pressure control valve of clutch K1, sub-gearbox 1) • Automatic gearbox pressure control valve 2 N216 (pressure control valve of clutch K2, sub-gearbox 2) • Cut-out clutch valve N689 (clutch pressure control valve K0) Cooling oil valve • Cooling oil valve N471 (controls clutch cooling) Gear selector valves • Valve 1 for sub-gearbox 1 N433 (controls the 1-N gear selector) • Valve 2 for sub-gearbox 1 N434 (controls the 5-3 gear selector) • Valve 1 for sub-gearbox 2 N437 (controls the 4-R gear selector) • Valve 2 for sub-gearbox 2 N438 (controls the 6-2 gear selector) Pressure and temperature sensor • Gearbox hydraulic pressure sensor G270 (measures pressure in ATF hydraulic pressure accumulator) • Clutch travel sender 1 G617 (measures pressure in piston of clutch K1) • Clutch travel sender 2 G618 (measures pressure in piston of clutch K2) • Temperature sensor in control unit G510ATF coolerATF pressure filterScrew plug for mechatronic unit filler portATF overflow portGearbox input speed sender 1 G632 (output shaft for sub-gearbox 1) Mechatronic unit for dual-clutch gearbox J743Gear actuator travel sensor 1 G487 (1-N, sub-gearbox 1) Gear actuator travel sensor 4 G490 (4-R, sub-gearbox 2)Gearbox input speed sender 2 G612 (output shaft for sub-gearbox 2)Gear actuator travel sensor 3 G489 (5-3, sub-gearbox 1) Gear actuator travel sensor 2 G488 (6-2, sub-gearbox 2)ATF hydraulic pumpATF hydraulic fluid reservoirIntake manifold for low-pressure pumpIntake port for high-pressure pump627_105The ATF hydraulic pump is a tandem pump. It consists of a lowpressure pump and a high-pressure pump. The low-pressure pump delivers, through the ATF intake filter, a large volume of ATF for cooling the clutch and lubricating all components.The high-pressure pump serves to activate the clutch and the gear selectors. It draws in ATF from the flooded mechatronic area through a port. To ensure that this area is kept flooded, a portion of the ATF flows from the low-pressure pump into the mechatronic area.17 BackForwards Ξ ContentsHybrid moduleThe hybrid module consists of the electric drive motor V141, which is encapsulated by a cooling jacket, clutches K1 and K2 for subgearboxes 1 and 2, as well as clutch K0. Clutch K0 is located on the secondary side of the dual mass flywheel and connects the electric drive motor V141 to the internal combustion engine. The clutch is activated and cooled through the hollow-drilled input shaft of sub-gearbox 1 by means of rotary feed-throughs.Input shaft for sub-gearbox 1Clutch K1Clutch K2Cooling jacketElectric drive motor: statorElectric drive motor: rotorGearbox input shaftInput shaft for sub-gearbox 2627_106Coolant return line for cooling the electric drive motor V141Clutch K018 BackForwards Ξ ContentsManual gearboxInput shaft for sub-gearbox 2 Output shaft 1 Clutch K1 Clutch K0Clutch K2627_111Input shaft for sub-gearbox 1Output shaft 2Electric drive drive motor V141Gearbox input shaftFront axle differential spur gearDual mass flywheel2 concentric clutch slave cylinders actuate the engagement bearings of clitches K1 and K2. Due to the engagement bearings, the clutch slave cylinders no longer have to rotate. No rotary feed-throughs with unwanted friction loss and unnecessary leakage are required.Coolant return line for cooling the electric drive motor V141Clutch K1 transmits the engine torque to sub-gearbox 1. The uneven gears (1, 3 and 5) are engaged in sub-gearbox 1. Clutch K2 transmits the engine torque to sub-gearbox 2, in which the uneven gears (2, 4 and 6) and reverse gear are engaged. The reverse gear pinion meshes with the 2nd gear pinion. The reverse gear is engaged by power transmission to output shaft 1 through clutch K2, input shaft 2, the engaged 2nd gear pinion and the engaged reverse gear pinion. Both output shafts mesh with the spur gear of the front axle drive.19 BackForwards Ξ ContentsSuspensionOverviewThe suspension system of the Audi A3 Sportback e-tron is based on the suspension system of the conventional-engined Audi A3 Sportback. 2 suspension system versions are available for the Audi A3 Sportback e-tron. The standard suspension is standard equipment. A suspension system with an increased ground clearance of 15 mm over the standard suspension is employed in markets with rough roads.ESC unit Continental MK100• Carry-over from Audi A3 SportbackMechanically adjustable steering column• Carry-over from Audi A3 SportbackWheels/tyres• Carry-over of wheels from Audi A3 Sportback wheel range • Exclusive wheel design (17“ and 18“) • Use of low rolling resistance tyres (16" and 17")McPherson front suspension• Carry-over from Audi A3 Sportback • Modified damper setupElectro-mechanical steering• Carry-over from Audi A3 SportbackBrake system pressure accumulator• First use in an Audi modelFront wheel brakes• 16“ brake system • Brake caliper TRW PC 57-25/14 • Brake disc diameter: 312 mm20 BackForwards Ξ ContentsMulti-function steering wheel• Carry-over from Audi A3 SportbackFour-link rear suspension• Carry-over from Audi A3 Sportback • Modified damper setup • Modified anti-roll bar based on higher axle load due to highvoltage battery • Partial modification of engine/gearbox bearings due to modified exhaust system suspension627_098Electro-mechanical brake servo• First use in an Audi modelRear wheel brakes• 15“ brake system • Brake caliper Continental FNC-M38 • Brake disc diameter: 272 mm21 BackForwards Ξ ContentsElectro-mechanical brake servoEven in electric-only mode it is necessary to boost the brake pressure when the brakes are applied by the driver. The intake manifold vacuum of the internal combustion engine cannot be utilised, as it is only available during conventional vehicle operation. The use of the electro-mechanical brake servo makes it possible to dispense with an additional vacuum pump in combination with a pneumatic brake servo. The electro-mechanical brake servo offers the following key advantages over a conventional pneumatic brake servo: • • • • Vacuum-independent brake servo High pressure generation dynamics High pressure regulation accuracy Constant brake pedal characteristic/pedal forceBrake fluid reservoirEngine-gearbox unit627_099Tandem master brake cylinderBrake servo control unit J539Push rod (brake pedal connection)22 BackForwards Ξ ContentsDesign and functional principlePiston rod Engine-gearbox unit Upper pinion shaft Booster sleevePush rod (brake pedal connection)Brake pedal position sender G100627_100Tandem master brake cylinderBrake servo control unit J539Lower pinion shaftThe brake pressure applied by the driver is boosted by the enginegearbox unit. An AC motor drives 2 pinion shafts through a reduction ratio. The splines of the pinion shafts are in mesh with the spline on the booster sleeve. The rotary motion of the pinion shafts is translated into a longitudinal motion of the booster sleeve. To increase the brake pressure, the booster sleeve is moved towards the tandem master brake cylinder (to the left in the diagram). After a defined amount of the idle travel (play), the booster sleeve comes into contact with the push rod and, if the electric motor is further activated, exerts force upon the push rod (in addition to the brake pressure applied by the driver). The electric motor is activated by the brake servo control unit J539. The control unit receives information on the position of the brake pedal and the push rod (= driver input) from the integrated brake pedal position sender G100.The position of the electric motor rotor and hence, indirectly, the position of the booster sleeve is monitored by a rotor position sensor (Hall sender) in the electric motor. The sliding assembly of the booster sleeve on the push rod, and the resultant separation of both components, ensures that the driver can apply brake pressure even if the boost function fails. Control unit J539 provides for terminal 15 run-on. If the vehicle is stationary and the driver is not applying the service brake, the run-on time is approximately 1 minute. If the vehicle is actively braked by the driver after terminal 15 is switched off, brake boost is maintained for up to approx. 6 minutes. After approx. 3 minutes and after 6 minutes, the driver is instructed to secure the vehicle against rolling and informed that brake boost will be deactivated. The signals from the brake pedal position sender G100 of the electro-mechanical brake servo are used for activating the brake light.23 BackForwards Ξ ContentsBrake system pressure accumulator VX70If required, the electric drive/AC motor is utilised as a generator in overrun mode to recharge the high-voltage battery (recuperation). The electric motor is "driven". As such, it creates drag and thereby generates additional braking torque at the driven wheels. If the driver were to apply the brake, this additional braking torque would immediately provide additional braking. As this process would be independent of driver inputs, it would be more the difficult for the driver to perform anticipatory braking. This is why it is important that a braking torque defined by the driver be available at any time and that the driver be able to gauge the effect of this braking torque. The hydraulic brake pressure is reduced during recuperation as this involves less technical complexity. This reduction is made with the aim of matching the total amount of "hydraulic" braking and "electrical" braking to the actual driver input. The brake system pressure accumulator VX70 is used in order to achieve this. The combination of "hydraulic" braking and "electrical" braking is referred to as "Blended Braking". By way of an example, the deceleration at a specific point in time (1 second after commencement of braking) is specially marked in the diagram. The amount of deceleration a, which the driver wishes to achieve, is provided by the total deceleration resulting from hydraulic braking torque aH plus the deceleration resulting from generator braking torque aG. a = aH + aGExample of "Blended Braking"Speed [kph] Deceleration [%g]aaHaG627_101Time [s]Key: Deceleration resulting from "hydraulic" braking torque aH Deceleration resulting from generator braking torque of AC drive aG Requested deceleration through brake pedal actuation by driver a Pedal travel Vehicle speed24 BackForwards Ξ ContentsDesign and functional principleThe brake system pressure accumulator VX70 is connected directly to the master brake cylinder, and thus to the hydraulic braking circuit. If the brake pressure applied by the driver (dependent on the additional braking torque of the electric drive during recuperation) has to be reduced, the electric motor of the pressure accumulator is activated by the brake servo control unit J539. The piston performs a lift motion due to the spindle drive in the cylinder, cylinder volume increases and brake fluid is taken in from the braking circuit. The braking pressure within the system, i.e. in the wheel brakes, decreases. At the same time, the brake boost provided by the electro-mechanical brake servo is reduced to ensure that the brake pedal does not "give". If the additional braking torque of the electric drive decreases again during active braking, or if the generator mode of the electric drive is fully deactivated, the previously reduced braking pressure must be increased again. Control unit J539 re-activates the electric motor of the pressure accumulator. The piston movement reduces the cylinder volume and the brake fluid in the cylinder is returned to the braking circuit. The pressure within the braking system increases accordingly.Bleed valveConnection to braking circuit PistonElectric motor Spindle drive627_102Service operationsThe electro-mechanical brake servo (including brake servo control unit J539) and the brake system pressure accumulator VX70 can be accessed under diagnostic address 23. If necessary, the components can only be replaced as complete assemblies by service personnel. After replacing the electro-mechanical brake servo (including control unit), online encoding of the control unit must be carried out. For this purpose, it is important to properly bleed the braking system. A subsequent basic setting procedure configures the system to acquire measured data from the corresponding sensors when the pedal is at rest (released) and when it is depressed. In addition, brake pressure is developed by activating the electric motor, and a pressure-volume curve is obtained. Component tolerances are thereby recognised and factored in during subsequent control operations. It is also necessary to perform the basic setting procedure for the pressure accumulator. Both basic setting procedures must also be carried out after replacing the pressure accumulator. Actuator diagnosis routines have been implemented for functiontesting the electro-mechanical brake servo and pressure accumulator.25 BackForwards Ξ ContentsHigh-voltage batteryOverview of hybrid componentsThe following high-voltage components are installed in the Audi A3 Sportback e-tron:Electrical brake servoThe dependencies governing the utilisation of braking torque lead toelectrical deceleration fluctuations which have to be compensated hydraulically in accordance with the driver's wishes. The main focal points during the development of the electrical brake servo were fully utilising the deceleration potential of the e-machine under driver initiated braking and extending the electric driving range of the e-machine.Power electronicsIt converts the direct current stored in the high-voltage battery to alternating current for the e-machine. The power electronics are integrated in the low-temperature cooling circuit 2.PTC heaterThe high-voltage heater (PTC) Z115 is connected to highvoltage battery charger 1 AX4 by a high-voltage line. It heats the coolant for the heater heat exchanger in the cabin during electric driving and is also integrated in the stationary air conditioning function.EngineFour cylinder engine with turbocharger and start-stop system: ► 1.4l TFSI (110 kW) Refer to “Internal combustion engine” on page 12.Charging portThe all-purpose charging cable can be used to charge the high-voltage battery at both household sockets and industry sockets using an interchangeable connecting plug.Electrical AC compressorThe electrical AC compressor is integrated into the high-voltage system and conditions both the cabin and the hybrid battery unit AX1 as required.e-machineThe e-machine is integrated into the gearbox via clutch K0. It is able to generate a braking torque at the wheel in dependence on RPM, battery temperature and state of charge.6-speed dual clutch gea S tronicNewly designed dual clutch gearbox consist engaged by multi-plate clutches K1 and K2 between 3 drive programs using the selecto26!Information All high-voltage components are connected to the vehicle chassis via an equipotential bonding. The equipotential bonding is a low-ohmic line connecting the high-voltage components to the vehicle chassis. BackForwards Ξ ContentsBattery cooling systemThe battery cooling system is integrated into the low-temperature cooling circuit 2. Refer to “„Low-temperature coolant circuit 2“ on page 48.High-voltage battery moduleThe high-voltage battery module consists of 8 modules each with 12 prismatic cells. The voltage is between 280 and 390 V, depending on state of charge.Fuel tankThe fuel tank has a capacity of 40 litres and is fitted over the rear axle.627_003arboxHigh-voltage linesAll high-voltage lines are double-insulated and colour-coded orange for easier recognition. To avoid incorrect assembly, the high-voltage lines are mechanically coded and identified by a coloured ring below the bayonet ring.12 volt car batteryFitted over the rear axle, it is responsible for supplying power to the low-voltage components.ting of 2 sub-gearboxes 2. It is possible to select or lever.!Information The information given in the workshop manual must be observed whenever performing work on equipotential bondings.27 BackForwards Ξ ContentsHybrid battery unit AX1In the case of the Audi A3 Sportback e-tron, the hybrid battery unit AX1 is mounted on the underside of the vehicle and consists of the following components: • • • • • • • Battery regulation control unit J840 High-voltage battery switch box SX6 8 cell modules each with 12 battery cells and controller Battery cell cooling system Connections for high-voltage wiring loom Connections for 12-volt electrical system Coolant connections The housing of the hybrid battery unit AX1 consists of a housing bottom section made from cast aluminium and a housing top section made from polymer. The housing top section is bolted and bonded airtight to the housing bottom section. The pressure equalisation elements and the pressure relief valve are installed under a cover on the top side of the hybrid battery unit AX1. Pressure changes inside the housing caused by temperature variation are equalised by the pressure equalisation elements. If the pressure inside the hybrid battery unit AX1 is too high, the pressure relief valve opens. The hybrid battery unit AX1 is connected to the vehicle chassis via an equipotential bonding.Cell moduleCellCell controller28 BackForwards Ξ ContentsSpecifications2 cell modules are bolted to a cooling element on the underside. The 4 cooling elements are connected to the hybrid battery unit AX1 in parallel. The inlet and outlet temperature sensors are integrated into the coolant connections. Rated voltage in V Cell voltage in V Number of cells Capacitance in Ah Operating temperature in °C Energy content in kWh Usable energy content in kWh Power in kW Weight in kg 352 3.7 96 25 –28 – +601) 8.8 7.02) Max. 90 120High-voltage battery switch box SX6The charging/discharging currents are reduced at temperatures of +50 °C and higher. 2) The state of charge is maintained at between 25 % and 85 %.1)Housing upper shell (polymer)InsulationBattery regulation control unit J840Heat sink of hybrid battery unit AX1Housing upper shell (aluminium casting)627_03629 BackForwards Ξ ContentsBattery regulation control unit J840The battery regulation control unit J840 is bolted into the hybrid battery unit AX1 from below. The battery regulation control unit J840 performs, among other things, the following tasks: • • • • Measurement and evaluation of the battery voltage Measurement and evaluation of the individual cell voltages Measurement of high voltage battery temperature Regulation of high-voltage battery temperature using coolant circulation pump 2 and solenoid valve 1 N88 in low-temperature circuit 2 The battery regulation control unit J840 is able to communicate with other control units in the vehicle via the interface to the powertrain CAN and hybrid CAN. A crash signal is transmitted from the airbag control unit J234 to the battery regulation control unit J840 via the powertrain CAN and a discrete line. If a crash signal is generated, the high-voltage contacts are opened and the high-voltage system is deactivated. The control unit communicates with the high-voltage battery switch box SX6 and the 8 cell controllers via a private CAN.High-voltage battery switch box SX6The following components are installed in the high-voltage battery switch box SX6: • • • • • • • Controller High-voltage system fuse 2 S352 High-voltage current sensor G848 Protective resistor for high-voltage battery N662 Power contactor 1 of high-voltage battery J1057 (HV pos.) Power contactor 2 of high-voltage battery J1058 (HV neg.) Precharging contactor of high-voltage battery J1044 (20 Ω)627_037When terminal 15 is switched "on", the power contactor 2 of high-voltage battery J1058 (HV negative) and the precharging contactor of high-voltage battery J1044 (20 Ω) are at first closed. A small amount of current flows through the resistor until the intermediate circuit capacitor 1 C25 in the electric drive power and control electronics JX1 is charged up. When the intermediate circuit capacitor is charged up, the power contactor 1 of highvoltage battery J1057 (HV positive) is closed and then the precharging contactor of high-voltage battery J1044 (20 Ω) is opened.The power contactors are opened if at least one of the following conditions is met: • Terminal 15 switched off • A crash signal from airbag control unit J234 is detected • Maintenance connector TW is opened • Fuse for power supply to power contactors terminal 30c is disconnected • 12 volt power supply for the hybrid battery unit AX1 is interrupted • Safety line openCell controllerThe cell controllers are a component part of the cell module. The cell controllers measure the voltage of each individual cell and, using an NTC resistor, the temperature of the cell module and send this data to the battery regulation control unit J840. The battery regulation control unit J840 evaluates the cell voltages and instructs the cell controllers to discharge cells with high cell voltage through a resistor. As a result, all cells achieve the same cell voltage and the hybrid battery unit AX1 has maximum capacity.30 BackForwards Ξ ContentsInsulation monitoringWhen the high-voltage system is active, the high-voltage battery switch box SX6 performs an insulation test every 60 seconds. The resistance between the high-voltage conductors and the housing of the hybrid battery unit AX1 is measured at the rated voltage of 352 V. Insulation faults in the high-voltage components and high-voltage lines are detected. The charging socket and the AC/DC inverter in the high-voltage charger are not tested due to the galvanic isolation between 230 V AC and 352 V DC. If an insulation fault is detected, this is indicated on the display in the dash panel insert. The customer is prompted to bring the vehicle in for repair.Safety lineThe safety line is a 12 volt ring line which interconnects all highvoltage components in series. The battery regulation control unit J840 inputs an electrical current of approximately 10 mA into the safety line and evaluates the current flow. In addition, the electric drive control unit J841 monitors the safety line. If the safety line is broken, the high-voltage system is immediately deactivated by the battery regulation control unit J840. The high voltage contacts are opened. The driver is notified via the display in the dash panel insert.STerminal 30c627_038Key: AX1 Hybrid battery unit AX4 High-voltage battery charger 1 J840 Battery regulation control unit JX1 Electric drive power and control electronics module S Fuse TW Maintenance connector for high-voltage system V470 Electrical AC compressor VX54 Three-phase AC drive Z115 High-voltage heater (PTC) High-voltage connector High-voltage line Safety line outside of component Safety line inside of component Line to protect the power supply to the line contactors31 BackForwards Ξ ContentsElectric drive power and control electronics module JX1The electric drive power and control electronics module JX1 is installed in the engine bay on the right-hand side and has the following components: • • • • • • • • Electric drive control unit J841 Drive motor inverter A37 Voltage converter A19 Intermediate circuit capacitor 1 C25 AC compressor fuse S355 Connections for high-voltage lines Connections for 12 volt electrical system Coolant connections The high-voltage line from the high-voltage charger is connected. All other high-voltage lines are bolted inside the electric drive power and control electronics module JX1. The electric drive power and control electronics module JX1 is connected to the vehicle chassis via an equipotential bonding. JX1 is cooled by low-temperature circuit 2.DesignSafety line connectorAC compressor fuse S35512-volt positive charging line627_039High-volt battery HV positive High-volt battery HV negativeElectric drive motor V141 Connections U, V, W Connection for high-voltage battery charger 1 AX412 volt on-board power plug32 BackForwards Ξ ContentsElectric drive control unit J841The electric drive control unit J841 monitors the rotor speed and position of the electric drive motor V141 using drive motor rotor position sensor 1 G713. The temperature of the electric drive motor V141 is monitored by the drive motor temperature sensor G712 and relayed to the engine control unit J623. The electric drive control unit J841 monitors component temperatures by means of temperature sensors in the power and control electronics JX1. The electric drive control unit sends this information to the engine control unit J623. The engine control unit uses the information to activate the pump for coolant circulation upstream of the power and control electronics V508 on demand. The electric drive control unit J841 is networked with the other control units via the powertrain CAN and hybrid CAN.Voltage converter A19The voltage converter A19 is a DC/DC converter and converts the 352 volt DC voltage to the low DC voltage (12 volts) of the vehicle's electrical system. A pulse inverter converts the voltage of the high-voltage battery to a voltage of 12 volts. The voltage is transmitted to the 12-volt electrical system by coil induction (galvanic isolation). As a result, there is no conductive connection between the high-voltage system and the 12-volt electrical system.Intermediate circuit capacitor 1 C25A further component in the power and electric drive control electronics module JX1 is the intermediate circuit capacitor 1 C25. Its task is to stabilise the voltage. Voltage fluctuations can occur for example at start-up or at kick-down (boost). The intermediate circuit capacitor 1 C25 is discharged actively and passively at terminal 15 "off" or if the high-voltage system is disabled due to a crash signal. Passive discharge means that the intermediate circuit capacitor 1 C25 is discharged through a high-ohmic resistor between HV positive and HV negative. In the case of active discharge, a highohmic resistor is connected. This ensures that intermediate circuit capacitor 1 C25 is discharged in the least possible time.Drive motor inverter A37The drive motor inverter A37 is, therefore, both a DC/AC converter and an AC/DC converter.Electric drive motor V141 as motor In electric driving mode, the drive motor inverter A37 converts the AC voltage of the hybrid battery unit AX1 to a 3-phase AC voltage. The voltage is converted by pulse width modulation. In the drive motor inverter A37 there are 6 transistors - 2 for each of the 3 phases U, V and W. Each phase has a separate transistor for positive and negative. When activated, the corresponding potential is connected. The transistors are activated by electric drive control unit J841 using pulse width modulated signals. RPM is regulated by changing the frequency, and the torque of the electric drive motor V141 by changing the activation times of the individual pulse widths.Electro-drive drive motor V141 in generator mode If electro-drive drive motor V141 is running in generator mode, drive motor inverter A37 converts the generated 3-phase AC voltage to a 352 V DC voltage. The high-voltage system is supplied with the generated DC voltage and the 12-volt electrical system is supplied through the voltage converter A19.33 BackForwards Ξ ContentsChargingCharging socket 1 for high-voltage battery charging UX4The charging socket 1 for high-voltage battery charging UX4 is located at the front in the radiator grille behind the charging flap. The charging socket temperature sensor G853 in the charging socket 1 for high-voltage battery charging UX4 and the actuator for high-voltage charging plug lock 1 F498 are integrated. The high-voltage battery charging socket 1 UX4 is connected to the vehicle chassis via an equipotential bonding. The figure shows the version for European markets.Communication Allows communication between vehicle and charging stationL1 Phase 1N Neutral conductorPE Protective earth Not assigned627_044Charging button module with displayThe charging button module comprises the instant charge button E766, the charging profile selection button E808 and the LED module for charging socket 1 L263 The LED module for charging socket 1 L263 indicates the current status of the charging cycle by various colours and by flashing or steady light. The active charging option is indicated by the red LED in the button.Charging profile selection button E808LED module for charging socket 1 L263Instant charge button E766627_045Overview of status LED messages Display LED is lit red LED is lit yellow LED is flashing yelow LED flashes green every 4 s for 60 s, then the LED goes out LED is flashing green LED lights up green and then the LED goes out Definition Plug has been detected, but is not locked; charging is not possible Plug has been detected and is not locked, but no mains voltage is available; charging is not possible Plug has been detected and is locked, selector lever not in position P; charging is not possible Timer for charging cycle is active, charging cycle starts depending on the programmed departure time Charging cycle is active Charging cycle completed34 BackForwards Ξ ContentsHigh-voltage battery charger 1 AX4The high-voltage battery charger 1 AX4 is connected to the electric drive power and control electronics module JX1 by a high-voltage line. The AC compressor fuse S355 is integrated into the highvoltage battery charger 1 AX4 between high-voltage battery HV positive and HV positive to high-voltage battery charger 1 AX4. The high-voltage battery charger 1 AX4 is cooled in the lowtemperature cooling circuit. The control unit for high-voltage battery charger 1 J1050 is integrated in high-voltage battery charger 1 AX4 and networked with the other control units via the powertrain CAN and the hybrid CAN. It has an internal coolant temperature sensor and transmits the coolant temperature to the engine control unit J623, thus allowing the latter to activate the pump for coolant circulation upstream of power and control electronics V508 on demand.A pulse inverter which converts the AC voltage of the operating unit to a DC voltage for charging the hybrid battery unit AX1 is integrated in high-voltage battery charger 1 AX4. The voltage is transmitted to the high-voltage onboard power supply by coil induction (galvanic isolation). As a result, there is no conductive connection between the AC system and the high-voltage system in the vehicle. The high-voltage battery charger 1 AX4 is connected to the vehicle chassis via an equipotential bonding.Charging socket 1 for high-voltage battery charging UX4 12-volt connection for charging socket, allows communication between vehicle and charging station via high-voltage battery charging socket 1 UX4The following sensors are connected to the control unit for highvoltage battery charger 1 J1050: • Charge socket temperature sensor G853 in the high-voltage battery charging socket 1 UX4 The following actuators are connected to the control unit for high-voltage battery charger 1 J1050: • Actuator for high-voltage flap lock 1 F496 • Actuator for high-voltage charging plug lock 1 F498 in the high-voltage battery charging socket 1 UX4Input voltage in V Output voltage in V Maximum current consumption in AAC 100 – 240 DC 220 – 450 16High-voltage heater (PTC) Z115627_043Electrical AC compressor V470 Electric drive power and control electronics module JX1 Coolant connections! !Information Preset charging timers are stored in the high-voltage battery charger 1 AX4.Information Electric drive power and control electronics module JX1 must be opened to replace the fuse. Pay attention to the safety instructions and follow the directions given in the workshop manual and Guided Fault Finding.35 BackForwards Ξ ContentsCharging the high voltage batteryCharging with alternating current When the vehicle is using the internal combustion engine to provide drive, the high-voltage battery is charged via the e-machine, which acts as a generator. To fully utilise the vehicle's capacity for electric driving, the highvoltage battery can be charged with alternating current from the mains power supply (home installation).Audi e-tron charging systemThe Audi A3 Sportback e-tron comes with the Audi e-tron charging system. For mobile use, the Audi e-tron charging system can be carried in a transport case. 2 replaceable mains cables are supplied for connecting to the 3-phase AC supply. 1 mains cable with a household plug and 1 mains cable with an industry plug. These plugs are country-specific.Status LED Safety glass Monochrome display Capacitive operating panelOperating unit The mains cables are encoded in such a way that the operating unit can detect whether a mains connection has been made with a household plug or an industry plug. If the vehicle is connected with an industry plug, the maximum power consumption is 16 A, resulting in a maximum charging output of 3.6 kW. If the vehicle is connected to a household socket, power consumption is limited to 10 A. The charging output can be set to 50 % or 100 % by the user. If the vehicle is connected to an industry socket, a charging output of 50 % is set automatically. This setting is maintained until the charger unit is disconnected from the mains. To prevent unauthorised access, the operating unit can be protected by entering a 4-digit PIN code. Before the charging cycle begins, the operating unit and the high-voltage charger unit in the vehicle communicate with one another. The operating unit has a self-diagnosis function and indicates any faults detected via the display. The operating unit has a temperature monitor. If the permissible temperature is exceeded, the charging cycle is interrupted until the temperature returns to an acceptable level.627_024HousingProtective frameVehicle cableCharging cable A charging cable is connected to the operating unit for connecting to the vehicle. These charging cables are country-specific and available in lengths of 2.5 m and 7.0 m.627_025627_027!36Information The charging cable must always be connected directly to a socket. Never use the charging cable together with an extension cable, a cable drum, a multiple socket outlet or a timer. Failure to heed this warning can result in damage to the operating unit or the home electrical system. BackCharging at home A charging dock for home installation is optional. The charging dock is attached to the wall via an built-in industry socket.Forwards Ξ ContentsThe operating unit is clipped into the charging dock and plugged into the built-in industry socket with the mains cable. Charging cables are available in various lengths for connecting the vehicle to the charging dock.Integrated mounting fixture (e.g. for garage wall)Fold-out front made from printed safety glassFront recess with mount for the operating unit of Audi e-tron charging systemMechanical lock for securing the supplied Audi e-tron charging system Receptacle for the vehicle cable with plug627_026Charging at public charging columns The Audi A3 Sportback e-tron can be charged at public charging columns. In some countries, a suitable charging cable must be carried in the vehicle. The figure shows the European-spec version.627_11237 BackForwards Ξ ContentsCharging cycleTo charge the high-voltage battery, the charging cable must be plugged into the vehicle, for example into the charging dock. When the charging cable is plugged into the vehicle, the charging plug is locked and cannot be removed. This is indicated by the yellow status LED. The charging cycle starts when the selector lever is in position P and the operating unit is connected to the mains voltage. If no timer is programmed, the charging cycle starts immediately. If a charging timer is programmed, but the state of charge of the high-voltage battery is less than 60 %, the charging cycle also starts immediately until the state of charge reaches approx. 60 %. If the instant charge button is pressed, the charging cycle stops and timer programming is activated. The active charging cycle is indicated by the flashing LED on the relevant button (refer to „Overview of status LED messages“ on page 34).627_028Displays of the status LED The status LED flashes green during the charging cycle. The charging cycle will stop if the vehicle is unlocked while charging is in progress. If the charging plug is not removed within 30 s of unlocking the vehicle, the starting cycle will restart.Charging times627_029The charging times are dependent on the mains voltage. The following table gives examples of charging times for several countries. Germany Household socket Industry socket 3 h 45 min 2 h 15 min China 5h 2 h 15 min USA 8h 2 h 15 min Japan 10 h 2 h 15 min!38Information The vehicle will not be ready to start if the charging cable is plugged in. The 12-volt battery is also charged. BackForwards Ξ ContentsHigh-voltage linesAll high-voltage lines in the high-voltage system are are colourcoded orange for identification purposes. Due to the high voltages and currents involved, the electrical lines have a significantly larger cross-section and are connected by special plug-in contacts. The electrical lines of the high-voltage system differ from the other lines in the 12-volt electrical system in terms of their core design. The high-voltage lines can also be provided with a corrugated plastic tube to provide protection against chafing. 3 different types of high-voltage line are used in the high-voltage system: singlepole and 2-pole lines with and without a safety line.Single-pole high-voltage lineConductor InsulationShieldingInsulation627_0522-pole high-voltage lineWith safety lineInsulation ShieldingWithout safety lineShielding InsulationHV pos.Safety lineHV neg.627_054 627_053High-voltage connectionsThe high-voltage lines on the Audi A3 Sportback e-tron are bolted onto or plugged into the high-voltage components. Screw connection • Electric drive power and control electronics JX1 • Three-phase AC drive VX54 To avoid incorrect assembly, all connections are mechanically encoded. 2-pole plug connection • • • • Electric drive power and control electronics JX11) High-voltage battery charger 1 AX41) High-voltage heater (PTC) Z1151) Electrical AC compressor V470627_055627_0561)In the case of these connections, a jumper for the safety line contacts is integrated into the plug.39 BackForwards Ξ ContentsElectrical AC compressor V47012 volt electrical systemThe electrical AC compressor V470 is bolted onto the internal combustion engine at the front and replaces the belt-driven AC compressor. It is integrated into the high-voltage system via the high-voltage battery charger 1 AX4 and is supplied with a voltage of 352 V. The AC compressor control unit J842 is integrated into the electrical AC compressor V470. It is controlled by the Climatronic control unit J255 via a LIN bus. The AC compressor is connected to the vehicle chassis by an equipotential bonding.Electric drive power and control electronics module JX1Condenser connectionType Rated voltage in V Speed in RPM Power consumption in kW Weight in kgScroll compressor 352 800 – 8600 3.6 6Refrigerant circuit connection AC compressor control unit J842627_040High-voltage heater (PTC) Z115When the vehicle is driven under electric power, the high-voltage heater (PTC) Z115 heats the coolant for the heater heat exchanger in the cabin. It is bolted into the vehicle underbody from below and connected to the high-voltage battery charger 1 AX4 by a highvoltage line. The integrated high-voltage heater (PTC) control unit J848 is connected to the Climatronic control unit J255 by a LIN bus. The high-voltage heater (PTC) control unit J848 monitors the inlet and outlet temperatures of the coolant via temperature sensors and sends this information to the Climatronic control unit J255. The Climatronic control unit J255 determines the required heating output and sends this information to the high-voltage heater (PTC) control unit J848 as a value between 0 and 100 %.High-voltage heater (PTC) control unit J848High-voltage line connection 12-volt electrical systemRated voltage in V Heating levels Activation mechanism352 3 PWM signal 0 – 100 %627_041Coolant connections!40Information Preset AC timers are stored in the Climatronic control unit J255. BackForwards Ξ ContentsMaintenance connector TWThe maintenance connector TW is located inside the engine bay and serves, firstly, as an electrical connection in the 12-volt control circuit for the high-voltage battery power contactors and, secondly, as a component part of the safety line. Opening the maintenance connector TW opens the safety line and breaks the 12-volt control circuit of the power contactors. The maintenance connector serves to de-energise the high-voltage system. Please use the relevant program in the vehicle diagnostic system to properly open and de-energise the high-voltage system. After it has been opened, the maintenance connector TW must be secured using padlock T40262/1 as a safeguard against restarting.In the engine bay The maintenance connector TW is labelled.627_057627_058Fuse panel in occupant cell The power supply fuse for the control circuit of the power contactors is labelled.627_059627_060!Information After de-energising the system, a check must be made to ensure that no voltage is present by running the diagnostic tester routine.41 BackForwards Ξ ContentsHybrid managerThe software of the engine control unit J623 has been extended to include the hybrid manager function. • Operating strategy • Torque distribution to the electric drive motor V141 and the internal combustion engine • High-voltage coordinator • Recuperation under braking and acceleration • Control of the coolant circuits The following hybrid-specific functions of the vehicle are controlled by the hybrid manager. • • • • • Control of hybrid displays Power meter Display in dash panel insert MMI energy flow diagrams e-tron statisticsOperating strategyThe operating strategy is configured to operate the vehicle efficiently using both drive systems. Taking the ambient conditions and information from other control units as well as the driving profile into account, the system decides whether to employ the internal combustion engine, the electric motor or both. Electric driving also requires enabling signals from other control units. A low state of charge in the high-voltage battery, a too-low ambient temperature, high torque demand or high cabin heating demand may necessitate starting the internal combustion engine.Internal combustion engine is Internal combustion engine start Electric drive Drive by internal combustion engine Hybrid drive Boost Recuperation with and without electrical braking off off on on on on or offElectrric drive motor operates V141 serves as Electric motor1) Electric motor1) Generator Electric motor1) Electric motor1) Generator1)In this operating mode, the 12-volt electrical system is supplied by the hybrid battery unit AX1.High-voltage coordinatorIn its capacity as a high-voltage coordinator, the hybrid manager monitors and coordinates all high-voltage components. It enables activation of the high-voltage system and controls the displays for hybrid operation and display of messages for the driver.Recuperation under braki