TECHNICAL DOCUMENTATION
SSP 630 Audi TT (Type FV)

This PDF is currently unavailable.
Read document text
Self Study Programme 630 For internal use onlyAudi TT(Type FV)Audi Service Training BackThe TT was a revolutionary car design when it was first unveiled in 1995. Its strictly geometrical, formally coherent design language made it an icon with huge charisma. For the third TT generation, the Audi designers have returned to many of these ideas and placed them in a new context that is as dynamic as it is diverse. The central motif was the circle – embodied in the curves of the roof line, and the front and the rear overhangs with their resolutely horizontal lines. From the side, many details of the new Audi TT are reminiscent of the first-generation classic in many respects. Together with the door, the fluid contour of the sill - the dynamic line - creates a striking refracting edge. The rear edges of the door are gently rounded. The broad wheel arches form geometric bodies. The front wheel arch breaches the line of the hood, which continues over the door as a tornado line and runs almost horizontally through to the tail as a strong body shoulder, culminating elegantly at the tail lights. The door handles feature a sturdy bow-shaped design, while the side mirrors sit atop the body shoulder – their slender bases are designed for enhanced aerodynamic and aeroacoustic performance.Forwards Ξ ContentsIn a design reminiscent of the first-generation TT, the flat glass housing also gives the impression of being a separate entity, and the slight kink in the rear side window accentuates the powerful C-posts. The circular fuel flap on the right side panel opens with a gentle tap. What is new is that there is no fuel tank cap beneath the flap. The filler nozzle slots straight into the tank filler, just like in a racing car. The tail of the new Audi TT is compact and powerful, the interplay of light and shade serving to enhance the impression of fluidity. Here too, three horizontal lines underline the impression of the new TT’s sporty width. The third generation of the compact sports car again commands attention with its emotional design and dynamic attributes. Standout features of the new coupe are its innovative driveline technology as well as its new operating and display concept.This SSP contains QR codes which you can use to access additional interactive content (refer to page 70).630_002New type designationDue to the fact that there are so many model families, the letters after the number are running out. Audi has therefore adopted a new type nomenclature. After the models of the new A3 generation had been given the type designation 8V, the Audi TT was assigned a new designation denoting its model family and has since received the type designations "8J" and "8N". In future, new models will no longer be identified in self study programmes by their launch year, but will be differentiated by their type designation. The new TT has been assigned to the "FV" model family.2ContentsIntroductionModel history _________________________________________________________________________________________________________________________________________________ 4 Presentation __________________________________________________________________________________________________________________________________________________ 6 In brief ________________________________________________________________________________________________________________________________________________________ 8BodyIntroduction _________________________________________________________________________________________________________________________________________________ 10 Joining technology __________________________________________________________________________________________________________________________________________ 12 Thermal "hot" and mechanical "cold" joining techniques _______________________________________________________________________________________________ 14 Attachments _________________________________________________________________________________________________________________________________________________ 16Passive safetyComponents _________________________________________________________________________________________________________________________________________________ 18 System overview ____________________________________________________________________________________________________________________________________________ 19 Front passenger airbag OFF warning lamp K145 ________________________________________________________________________________________________________ 20 In-car airbags ________________________________________________________________________________________________________________________________________________ 22EnginesDiesel engine ________________________________________________________________________________________________________________________________________________ 24 Petrol engines _______________________________________________________________________________________________________________________________________________ 26 Engine/gearbox combinations _____________________________________________________________________________________________________________________________ 27Power transmissionOverview _____________________________________________________________________________________________________________________________________________________ 28 quattro drive ________________________________________________________________________________________________________________________________________________ 28 6-speed double-clutch gearbox 0D9 – S tronic ___________________________________________________________________________________________________________ 30ChassisOverall concept ______________________________________________________________________________________________________________________________________________ 32 Axles and wheel alignment ________________________________________________________________________________________________________________________________ 33 Brake system ________________________________________________________________________________________________________________________________________________ 40 Electronic Stability Control (ESC) __________________________________________________________________________________________________________________________ 43 Steering system _____________________________________________________________________________________________________________________________________________ 44 Wheels and tyres ____________________________________________________________________________________________________________________________________________ 47Electrical systemInstallation locations of control units ____________________________________________________________________________________________________________________ 48 Topology _____________________________________________________________________________________________________________________________________________________ 50 Audi virtual cockpit _________________________________________________________________________________________________________________________________________ 52 Audi drive select _ ____________________________________________________________________________________________________________________________________________ 54 Start-stop system ___________________________________________________________________________________________________________________________________________ 57Air conditioningIntroduction _________________________________________________________________________________________________________________________________________________ 60 A/C operating and display unit ____________________________________________________________________________________________________________________________ 61 Dash panel temperature sensor G56 _ _____________________________________________________________________________________________________________________ 63 Seat systems ________________________________________________________________________________________________________________________________________________ 65InfotainmentOverview of versions ________________________________________________________________________________________________________________________________________ 66ServiceInspection and maintenance _ ______________________________________________________________________________________________________________________________ 68 Information on QR codes _ __________________________________________________________________________________________________________________________________ 70 Self study programmes _ ____________________________________________________________________________________________________________________________________ 71The Self Study Programme teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a Repair Manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. This content is not updated. For further information on maintenance and repair work, always refer to the current technical literature.NoteReference3 BackForwards Ξ ContentsIntroductionModel historyIn 1995 Audi presented a pioneering study: the Audi TT. The Coupé (IAA Frankfurt, 1995) and Roadster (Tokyo Motor Show, 1995) showcars were followed by the production versions of the Audi TT Coupé in 1998 and Audi TT Roadster in 1999. When the firstgeneration Audi TT came on the market in 1998 it was a design revolution. Radical in design, but suitable for everyday use – that was the motto for the first Audi TT. The requirement specifications laid down "a sports car concept with high practicality". The third generation of this classic has adopted many of the design elements that characterised the first-generation TT – coupled with innovative technology. Between the first and third generation of the TT lie nearly 20 years of development in technology and design. Here, in brief, are the key milestones in the model history of the Audi TT.2007A new edition of the Roadster also went into production a year after the Coupé.2000 – 2003The TT-R racing car prototype provided the basis for the successful reentry of Audi into the German Touring Car Championship (DTM).1998Start of production of the Audi TT Coupé (Type 8N) in Ingolstadt and Győr.2006The second generation of the Audi TT (Type 8J) is rolled out featuring a new design and new technology.1999Start of production of the Audi TT Roadster (Type 8N) in Ingolstadt and Győr.1995Presentation of the Audi TT study as a Coupé at the IAA in Frankfurt.4 Scan the QR code to find out more about the model history of the Audi TT. BackForwards Ξ Contents2010The second generation of the TT makes a successful entry into motor racing, e.g. in the Long Distance Championship.2012Audi reveals the Audi TT RS plus, the most powerful version of the sports car, powered by a 5-cylinder TFSI engine.2008Audi presents the Audi TT clubsport quattro study with shorter windscreen and sporty attachments.2014The allroad shooting brake study provides a glimpse into the design of the new Audi TT.2014The third generation of the Audi TT (Type FV) is released – first as a Coupé and shortly afterwards as a TTS.630_035 5 BackForwards Ξ ContentsPresentationThe third generation of the compact sports car again commands attention with its emotional design and dynamic attributes. Standout features of the new coupe are its innovative driveline technology as well as its new operating and display concept. The Audi TT also has a number of other technical highlights which are explained in detail in this self study programme. Here is a quick summary.Engines4-cylinder engines with turbocharger and start-stop system: ► 2.0l TFSI (169 kW) ► 2.0l TFSI (228 kW) ► 2.0l TDI (135 kW)Assistance systemsThe following systems are optionally available: ► Audi side assist ► Camera-based traffic sign recognition ► Audi active lane assist ► Park assist system with ambient displayHeadlightsLED headlights or headlights incorporating Audi Matrix LED technology, consisting of 12 LEDs where the high beam is generated by controllable individual LEDs. The dynamic turn signals in the headlights and in the tail lights light up sequentially in the direction in which the driver is steering.Air conditioningChoice of manual or automatic air conditioning system. All control functions are integrated into the air vents. The automatic air conditioning system has small displays which show the selected setting.6 BackForwards Ξ ContentsBodyAudi Space Frame (ASF) body made from aluminium and steel with high-strength and ultrahigh-strength steel alloys, die-cast aluminium nodal elements and side panels as well as a roof made of aluminium.Power transmissionFull-time quattro drive – systematically developed and refined for the TT – with electro-hydraulic multiplate clutch on the rear axle. It is possible to customise the all-wheel drive characteristics by networking the quattro drive with Audi drive select.630_007Displays and operationFully digital Audi virtual cockpit instrument cluster with dynamic animations and graphics. New MMI control panel on the centre tunnel console with 2 toggle buttons. On each side of the central rotary pushbutton, there are there are two buttons together with a main menu button and a back button. Touch-sensitive touch pad on the top of the rotary pushbutton.SuspensionThird-generation Audi magnetic ride adaptive damper control as optional suspension version. Audi magnetic ride is adjustable in 3 stages via Audi drive select. Electro-mechanical progressive steering, where the steering ratio becomes more direct with increasing steering input.7 BackForwards Ξ ContentsIn briefDimensions1572 1832630_00313539531552 1966630_004993 38588842505 4177788630_0058813 BackForwards Ξ Contents1449213621824 1000630_006Exterior dimensions and weightsLength in mm Width in mm Height in mm Front track width in mm Rear track width in mm Wheelbase in mm Kerb weight in kg Gross vehicle weight in kg 4177 18324) 1353 1572 1552 2505 12655) 1665Inner dimensions and other specificationsFront cabin width in mm Front headroom in mm Front shoulder width in mm Rear headroom in mm Through-loading width in mm Load sill height in mm Boot capacity in l Drag coefficient cw Capacity of fuel tank in l 14492) 9933) 13621) 858 1000 813 305/7126) 0.30 50Shoulder room width Elbow room width 3) Maximum headroom 4) Excluding mirror 5) With 2.0l TDI engine 6) With rear backrest folded down1) 2)All dimensions are given in millimetres and refer to the unladen weight of the vehicle.9 BackForwards Ξ ContentsBodyIntroductionWith its hybrid material concept, the bodyshell of the Audi TT represents a new evolutionary stage of Audi Space Frame technology (ASF). The bodyshell of the 3rd generation uses components of the Modular Transverse Platform (MQB) whereby the TT, at 2505 mm, has the shortest wheelbase within the MQB. The substructure comprises the cross members, sections of the A-posts, the bulkhead, floorpan, rear wheel arches and the tail panel. The hot-formed steel in the substructure weighs 39.5 kg and accounts for almost a quarter of the total structural weight. Prior to forming, they are heated to about 1000 °C and then immediately cooled to about 200 °C in a water-cooled pressing tool during the forming process. This drastic change in temperature produces an extremely strong iron-carbon microstructure. The form-hardened steel has a relatively low wall thickness and is correspondingly light. Ultra-high-strength, cold-formed steel components together with extruded aluminium sections for the outer sills and aluminium panels for the rear wheel arches complete the substructure of the Audi TT.Body substructure630_074Substructure integrated into the MQB platform (PQ-37)Torsional rigidityIn terms of torsional resistance, the hybrid ASF is custom made for the Audi TT (Type FV) In comparison with its predecessor (Type 8J), which itself had very high rigidity, the TT (Type FV) has 23 % higher static torsional rigidity while retaining a high level of dynamic rigidity.Key:Sheet aluminium Die-cast aluminium Aluminium section Ultrahigh strength steel (hot-formed) Advanced high strength steel High strength steel Low strength steel10 Scan the QR code to find out more about the bodyshell of the Audi TT. BackForwards Ξ ContentsDesignIn terms of its structural design the occupant cell, which weighs only 68 kg, is an aluminium lattice with 4 castings which form the nodal elements of the bodyshell. Large nodal elements at the A-posts connect the side roof frame profile, sill, window cross member and the upper longitudinal section in the front end. 2 smaller cast nodal elements above the rear window connect the roof arch to the flat C-posts and the rear roof cross member.Outer skinThe entire outer skin of the Audi TT is made from aluminium: • • • • Front wings Sidewalls Roof Attachments: bonnet, doors and boot lidThe last two components alone are, together, 15.5 kg lighter than the corresponding steel components. In total, the complete bodyshell with attachments weighs 276 kg.630_01211 BackForwards Ξ ContentsJoining technologyThe key to optimising the body structure is using "the right materials in the right place". The resulting challenge for the joining technology was to develop, to the greatest extent possible, universal and reliable solutions for the large variance in material/thickness combinations in the body. In the case of the TT, Audi uses "cold" joining techniques such as riveting, screwing and clinching to create the aluminium/steel hybrid structure. Adhesive is also used to strengthen the connection and to prevent contact corrosion of the aluminium/steel joint. The body is held together by the following types of join: • • • • • • 3020 spot welds 1113 punch rivets 44 solid punch rivets 128 flow-drill screws 199 clinching points 1.9 m of MIG/MAG welds (metal inert gas/metal active gas) • 4.9 m of laser-welded seams • 76 m of adhesiveTypes of join used in the Audi TTBondingLaser weldingSemi-tubular punch rivetingResistance spot welding12 BackForwards Ξ ContentsSafety precautions against contact corrosionAluminium has a passivating surface oxide layer which protects the underlying material against the elements. This is why an unpainted aluminium component does not normally corrode. However, if aluminium comes into contact with a metal which has a positive electrical potential relative to aluminium in the electrochemical series and it is an electrolyte, such as salt water, contact corrosion will occur. The greater the difference in electrical potential, the greater the corrosion will be. Since aluminium is usually the less noble metal, it is degraded. Contact corrosion can also occur if unsuitable connecting elements (screws, nuts, washers, etc.) are used. Therefore, a number of precautions must be taken in order to prevent this process from occurring during body production and repair work. For this reason, Audi uses only connecting elements with a special surface coating for the aluminium/steel hybrid construction used in the TT. In addition, all rubber and plastic parts and all adhesives are made of non electrically conductive materials. As a further precaution, all hybrid connections are sealed with polyvinyl chloride (PVC) or with wax after cataphoretic dip primer coating.Solid punch rivetingClinchingMIG/MAG weldingFlow drill screwing630_075 13 BackForwards Ξ ContentsThermal "hot" and mechanical "cold" joining techniquesThe choice of the right joining technique in modern body construction is material-dependent. Welding similar materials is still the most frequently used joining technique. These welding and soldering techniques are so-called "hot" joining techniques and have a large variety of possible applications. However, the heat input causes high internal stresses in the component, which often can only be compensated through time-consuming rework. The mechanical "cold" joining technique has the decisive advantage over the thermal joining technique that hybrid joints can be reliably produced between different types of materials. The positive properties of the material are not adversely affected by the thermal influences. The following "cold" joining techniques are used: • Punch riveting • Clinching • Flow drill screwing • Seaming • Bonding It often makes good sense to combine the mechanical spot joining techniques with bonding methods. Firstly, this increases the strength of the joint and, secondly, the adhesive also acts as insulation in the case of hybrid aluminium/steel joints. This, in combination with seam sealing, prevents direct contact between the metals and thus ensures that corrosion cannot occur. In addition, an intelligently selected adhesive concept can also help to absorb the, in some cases, differing degrees of thermal expansion of the individual materials."Hot" joining technique in the Audi TTMIG/MAG welding In the case of the MIG/MAG (MIG = metal insert gas, MAG = metal active gas) welding technique, an electric arc forms between the melting, automatically fed welding wire (electrode) and the workpiece. A separately admixed gas protects the electric arc and the welded surface against the ingress of ambient air. The inert gas and welding wire have to be adapted to the basic material. Advantages: • Versatility in use • High weld seam strength • Outstanding thin panel properties630_076Resistance spot welding In the case of resistance spot welding, panels are welded together using, in most cases, opposed electrodes under the application of force, pressure and electrical current. Advantages: • No additional connecting element • No heat influence zone • Short welding timeLaser welding In the case of laser welding, the focussed laser beam serves as an energy source. In the welding head, the laser beam is focussed by a lens and reflected back onto the workpiece by mirrors. At the point of contact, the laser beam melts the workpiece. Welding can be performed both with and without welding filler material. Advantages: • Less influence of heat • Less thermal distortion • Less time spent on rework630_077630_065 14 BackForwards Ξ Contents"Cold" joining technique in the Audi TTPunch riveting Punch welding is a method where non-prepunched workpieces are joined together by inserting a rivet (semi-tubular rivet or solid punch rivet) into two or more layers of the workpiece, the rivet piercing the upper workpiece layers and then expanding in the lower workpiece layer. Advantages: • No prepunching needed • High dynamic strength • Form-fitting and non-positive connection • Ideal for hybrid joining630_061Semi-tubular punch rivetSolid punch rivet630_062Clinching In the case of clinching, panels or sections are joined together by cold-forming the materials to produce a form-fitting and nonpositive connection without the need for an auxiliary joining element such as a rivet. In this case, the connections can have two or more layers. Advantages: • No additional connecting element • Protects the surfaces of coated workpieces630_063Flow drill screwing A special, coated screw is inserted through partially non-prepunched workpieces by applying a high contact pressure. Due to the high pressure and high RPM, the screw forms a thermoflow hole without producing any burr. The screw penetrates the material and, in the process, cuts its own thread. Advantages: • High strength through thermoflow process • Ideal for applications in which the material is accessible on one side only • Easy to disconnect630_064Bonding In addition to punch riveting, clinching, solid punch riveting, flow drill screwing and resistance spot welding, additional adhesive bonds are used in certain areas. These bonds increase the strength of the connection. Adhesive is also used in seamed connections, as is the case at the rear wheel arch. In other areas of the bodyshell, use is made of adhesive beads to provide sealing and insulation between aluminium and steel, as well as for noise reduction. Advantages: • Large area connections are possible • Unchanged surface and microstructure • Suitable for connecting different materials • Sealing connection630_07815 BackForwards Ξ ContentsAttachmentsBonnet lock with integrated catch hookThe Audi TT marks the introduction of a new type of bonnet locking system. It takes advantage of the synergy resulting from the Modular Transverse Platform and will also be used in other Audi models in future. The advantage of this system is that the catch hook is integrated into the bonnet lock, offering improved ease of use. Initially, the two bonnet locks are unlocked as before using the release lever inside the vehicle (driver side footwell) and a Bowden cable. Next, the two catch hooks on the boonet locks are released by the release element integrated in the lock mounting and an additional Bowden cable.Bonnet lock, rightCatch hook, rightCatch hook, leftRelease element in lock mountingBonnet lock, left630_079Filler flap moduleThe TT is the first Audi model to feature a filler flap free locking system which, in keeping with tradition, is integrated into the right side panel. There is no longer a filler cap beneath the filler flap. The fuel nozzle slots directly into the filler neck, just like in a racing car. Two flaps are pushed to the side when the fuel nozzle enters the filler neck and seal the filler neck again after refueling has been completed. As in the predecessor model (Type 8J), the filler flap module has an aluminium-look finish and is mounted in six imitation bolts. The fuel flap can be opened by tapping lightly on the embossed TT logo and is locked and unlocked automatically when the central locking system is actuated.630_080 16 BackForwards Ξ ContentsElectro-mechanical rear spoilerThe Audi TT has an electrically retractable rear spoiler as standard. There is a choice of 2 operating modes for extending and retracting the rear spoiler. Driving stability is increased significantly at high speeds when the rear spoiler is extended.Operating mode Automatic mode Manual modeFunction Automatic extension and retraction: The rear spioler is automatically extended when a speed of approximately 120 kph is exceeded and retracted again at about 80 kph. Manual extension: The rear spoiler is extended fully with a short touch of the rear spoiler button in the centre console. Manual retraction: • At a speed of up to about 20 kph, the rear spoiler can be retracted by holding the button down. • At a speed of between 20 kph and 120 kph, the rear spoiler can be retracted fully by touching the button.Sheet-metal spoiler bladeDrive unit with drive shaft and pivot mechanism (hinge)Boot lid630_081Design The unit comprising the rear spoiler module and the spoiler blade is integrated into the boot lid of the Audi TT. The rear spoiler module consists of the drive unit, drive shaft and pivot mechanism (hinge) including the self-adjusting elements. The rear spoiler module is attached to a sheet-metal spoiler painted in the body colour.Note If repair work is needed, the spoiler blade can be replaced individually. The rear poiler module must be replaced completely if damaged.17 BackForwards Ξ ContentsPassive safetyComponentsDepending on country version and trim level, the passive occupant and pedestrian protection system in the Audi TT can comprise the following components and systems: • • • • • • • • • • • • Airbag control unit Driver airbag Front passenger airbag Front side airbags Head airbags Knee airbag, driver and front passenger sides Front airbag crash sensors (acceleration sensors) Front crash sensors for side crash detection (pressure sensors) Rear crash sensor for side crash detection (acceleration sensor) Pedestrian protection crash sensor (acceleration sensor) Crash sensors for pedestrian protection (pressure sensors) Front inertia-reel seat belts with pyrotechnic belt tensioners • Inertia-reel seat belts with active belt force limiters • Rear inertia-reel seat belts with pyrotechnic belt tensioners, driver and front passenger sides • Seat belt warning for all seats • Seat belt switches on all seats in the seat belt buckles • Seat occupancy sensor in front passenger seat • Airbag disabling switch, front passenger side • Front passenger airbag OFF and ON warning lamps • Driver and front passenger seat position sensors • Pedestrian protection trigger • Battery disconnectAdditional equipmentEquipment specifications can vary due to the different requirements and statutory provisions for car makers in the various markets.Key to figure on page 19: E24 Driver side seat belt switch E25 Front passenger side seat belt switch E224 Airbag disabling switch, front passenger side E258 Rear seat belt switch, driver side E259 Rear seat belt switch, front passenger side G128 G179 G180 G256 G283 G284 G551 G552 G553 G554 G598 G599 G693 G851 G852 J234 J285 J533 J706 Passenger side seat occupancy sensor Side airbag crash sensor, driver side Side airbag crash sensor, front passenger side Rear side airbag crash sensor, driver side Front airbag crash sensor, driver side Front airbag crash sensor, front passenger side Belt force limiter, driver side Belt force limiter, front passenger side Seat position sensor, driver side Seat position sensor, front passenger side Pedestrian protection trigger 1 Pedestrian protection trigger 2 Pedestrian protection crash sensor, centre Driver side crash sensor for pedestrian protection 2 Passenger side crash sensor for pedestrian protection 2 Airbag control unit Control unit in dash panel insert Data bus diagnostic interface (gateway) Seat occupancy recognition control unit K19 Seat belt reminder warning lamp K75 Airbag warning lamp K145 Front passenger airbag OFF warning lamp (ON and OFF status of front passenger airbag is indicated) N95 Driver side airbag igniter N131 Front passenger side airbag igniter 1 N132 Front passenger side airbag igniter 2 N153 Seat belt tensioner igniter 1, driver side N154 Seat belt tensioner igniter 1, front passenger side N196 Rear seat belt tensioner igniter, driver side N197 Rear seat belt tensioner igniter, front passenger side N199 Side airbag igniter, driver side N200 Side airbag igniter, front passenger side N251 Head airbag igniter, driver side N252 Head airbag igniter, front passenger side N253 Battery isolation igniter N295 Knee airbag igniter, driver side N296 Knee airbag igniter, front passenger side N490 Driver airbag relief valve igniter N491 Front passenger airbag relief valve igniter T16 16-pin connector, diagnostic portNote The diagrams in the chapter entitled "Passive occupant safety" are schematic diagrams and serve to provide a better understanding.18 BackForwards Ξ ContentsSystem overviewThe system overview shows the components for all markets. Keep in mind that this constellation is not possible in series production.Key: Powertrain CAN bus Convenience CAN bus Diagnostics CAN bus Input signal630_040Output signal19 BackForwards Ξ ContentsFront passenger airbag OFF warning lamp K145A new front passenger airbag OFF warning lamp K145 is used in the Audi TT. The warning lamp is integrated into the interior light. Previously, the indicator lamp indicated when the front passenger airbag was OFF. The warning lamp did not indicate when the front passenger airbag was ON. The new warning lamp now also indicates when the front passenger airbag is ON.ON warning lamp630_042Text indicating the status of the front passenger airbagOFF warning lampVersion 1: Behaviour of the warning lamp in vehicles with "airbag disabling switch, front passenger side E224" When the ignition is turned on, the ON and OFF warning lamps including the PASSENGER AIRBAG text light up for about 4 seconds during the initialisation phase (self-test). If the keyswitch is at ON, the text display and the ON warning lamp subsequently light up for about 60 seconds. If the keyswitch is at OFF, the text display and the OFF warning lamp are continuously lit.Behaviour of the warning lamp in response to a change of status • If the status of the front passenger airbag changes from OFF to ON after the ignition is turned on, the OFF warning lamp goes off after a qualification phase of about 2 seconds and the ON warning lamp comes on after a qualification phase of about 2 seconds. The ON warning lamp and the PASSENGER AIRBAG text display go out after about 60 seconds. • If the status of the front passenger airbag changes from ON to OFF while the ignition is on, the OFF warning lamp and the PASSENGER AIRBAG display light up continously after a qualification phase of about 2 seconds.Display behaviour after switching the front passenger airbag on and offInitialisation phase (4 sec.) Qualification phase (2 sec.) Qualification phase (2 sec.)Terminal 15ON OFFAirbag disabling switch, front passenger side E224"ON" "OFF" lights up for 60 sec. lights up for 60 sec.Warning lamp ONON OFFWarning lamp OFFON OFF lights up for 60 sec.Text PASSENGER AIRBAGON OFF630_043 20 BackVersion 2: Behaviour of the warning lamp in vehicles with "seat occupancy recognition control unit J706". • If the ignition is turned on and the front passenger seat is occupied by an adult, the OFF warning lamp lights up for about 4 seconds during the initialisation phase (self-test). The ON warning lamp is lit continuously.Forwards Ξ Contents• If the ignition is turned on and the front passenger seat is vacant occupied by an child seat, the ON warning lamp lights up for about 4 seconds during the initialisation phase (self-test). The ON warning lamp is lit continuously.The PASSENGER AIRBAG text display is lit continuously when the ignition is on.Behaviour of the warning lamp in response to a change of status • If the status of the front passenger airbag changes from ON (seat occupied) to OFF (seat vacant) while the ignition is on, the ON warning lamp goes out. At the same time, the OFF warning lamp flashes for about 5 seconds and then lights up continuously. • If the status of the front passenger airbag changes from OFF (seat vacant) to ON (seat occupied) while the ignition is on, the OFF warning lamp goes out. At the same time, the ON warning lamp flashes for about 5 seconds and then lights up continuously.Display behaviour after switching the front passenger airbag on and offInitialisation phase (4 sec.)Initialisation phase (4 sec.)Terminal 15ON OFFPassenger side seat occupancy sensor G128"Occupied" "Vacant" flashes for 5 sec.Warning lamp ONON OFF flashes for 5 sec.Warning lamp OFFON OFFText PASSENGER AIRBAGON OFF630_04421 BackForwards Ξ ContentsIn-car airbagsDriver airbag Front passenger airbag Knee airbag Head airbag, driver and front passenger sideKnee airbagSide airbag630_01322 BackForwards Ξ ContentsHead airbagThe Audi TT is equipped with head airbags for the first time. The limited installation space resulting from the shape of the bodyshell presented a number of engineering challenges. Despite very the lack of installation space and the absence of a B post, the Audi TT meets the 2013 US statutory requirements according to FMVSS 226 – Ejection Mitigation.Side airbagDescription of FMVSS 226 – Ejection Mitigation • FMVSS = Federal Motor Vehicle Safety Standards • 226 – Ejection Mitigation = the protection of vehicle occupants from ejection through the side windows, particularly in a rollover.Side airbagThe side airbag in the Audi TT is designed as a thorax-pelvis airbag, and not as a head-thorax airbag. The reason for this is that simultaneously installed head airbags and head-thorax airbags would obstruct each other, and thus be less effective in protecting protect the vehicle occupants.Head airbag attachment Due to the requirements of FMVSS 226 – Ejection Mitigation and the absence of a B post, the head airbag in the Audi TT is attached by screws, and not by clips like in other current Audi vehicles. The screws in question are self-tapping screws, which are inserted in different material thickness and different materials (aluminium/ steel).Left-hand side roof frameAttachment by self-tapping screwsLeft-hand side head airbag630_046Reference For information on removing and installing the head airbag, please refer to the workshop manual.23 BackForwards Ξ ContentsEnginesDiesel engineTorque/power curve of 2.0l TDI engineEngine with engine code CUNA Power output in kW Torque in NmEngine number of engine block630_020Engine speed [rpm]630_021Features Engine code Type Displacement in cm3 Stroke in mm Bore in mm Cylinder spacing in mm Number of valves per cylinder Firing order Compression ratio Power output in kW at rpm Torque in Nm at rpm Fuel type Engine management system Maximum injection pressure in bar Emission standard CO2 emissions in g/kmSpecifications CUNA 4-cylinder inline engine 1968 95.5 81.0 88.0 4 1-3-4-2 16.2 : 1 135 at 3500 - 4000 380 at 1750 - 3000 Diesel acc. to EN 590 Bosch EDC 17 2000 with solenoid injector CRI2-20 EU 6 11024 BackForwards Ξ ContentsBalancer shaftsTo neutralise second-order free inertial forces, use is made of a balancer shaft system which is integrated into the cylinder block above the crankshaft. Drive is provided by the crankcase through helical-cut gears on the output side. The shafts and the idle gear are located radially and axially by a roller bearing. The bearings are lubricated with oil spray from the cylinder block. To further reduce the frictional force of the balancer shafts, the gear width of the drive gears has been halved. The partially coated Spacecoat® idler gear is needed for reversing the direction of rotation. Spacecoat® is a specially additivised polymer layer that allows quick, inexpensive and precise assembly of gear wheels. The coating allows backlash adjustment within very narrow tolerances, which significantly improves engine acoustics.630_015Previously used balancer shaft gear with a gear width of 12 mmNewly developed balancer shaft gear with a gear width of 6 mmBalancer shaft, leftBalancer shaft, rightBalancer shaft idler, partially coated over a width of 5 mm630_014Reference For further information about the EA288 engine series, please refer to Self Study Programme 608 "Audi 1.6l / 2.0l 4-cylinder TDI engines".25 BackForwards Ξ ContentsPetrol enginesTorque/power curve of 2.0l TFSI engineEngine with engine code CHHC Power output in kW Torque in NmThe following modifications have been made to be engine so it is suitable for use in the Audi TT: • Oil pan top section with 2 oil return lines • One track with skip protection in the chain drive • Crankcase breather with modified fine oil separator • Modified aluminium coolant pumpTechnical specifications for the 2.0l TFSI engine (CJXC) of the Audi TTS were not available at the editorial deadline.Engine speed [rpm]630_041Features Engine code Type Displacement in cm Stroke in mm Bore in mm Number of valves per cylinder Firing order Compression ratio Power output in kW at rpm Torque in Nm at rpm Fuel type Engine management system Emission standard CO2 emissions in g/km3Specifications CHHC 4-cylinder inline engine 1984 92.8 82.5 4 1-3-4-2 9.6 : 1 169 at 4500 - 6200 370 at 1600 - 4300 Premium unleaded 95 RON Simos 18.1 EU 6 158Reference For more information on the 2.0l TFSI engine, please refer to Self-study Programme 606, "Audi 1.8 and 2.0l TFSI EA888 series engines (3rd generation)".26 BackForwards Ξ ContentsEngine/gearbox combinationsThe engine-gearbox combinations shown below are those available at market launch.Engines2.0l TFSI engine (CHHC)2.0l TFSI engine (CJXC)1)2.0l TDI engine (CUNA)6-speed manual gearbox 0FB MQ350-6F6-speed manual gearbox 02Q MQ350-6F6 speed quattro manual gearbox 0FB1) MQ350-6A 6-speed quattro doubleclutch gearbox 0D91) DQ250-6F 6-speed quattro doubleclutch gearbox 0D9 DQ250-6A Rear axle drive 0CQ 5th generation Haldex coupling1)To be introduced at a later date.Breakdown of manufacturer codes: e.g.: MQ350-6F M D Q 350 Manual gearbox Double-clutch gearbox Transverse mounting Rated torque capacity 6 F A Number of gears Front-wheel drive All-wheel quattro drive27 BackForwards Ξ ContentsPower transmissionOverviewThe Audi TT largely adopts the tried and tested power transmission technology of the 2013 model Audi A3 (Type 8V). The diagram shows the quattro drive of the Audi TT with 6-speed double-clutch gearbox 0D9 – the 5th generation S tronic and Haldex coupling 0CQ.Scan the QR code to find out more about the quattro drive of the Audi TT.Rear axle final drive unit 0CQ, 5th generation Haldex couplingquattro driveThe Haldex coupling software has been specially adapted for the Audi TT. The new software provides both enhanced driving dynamics and higher efficiency. The Haldex coupling software now makes more intensive use of measured data relevant to driving dynamics and continuously computes the exact driving status of the vehicle, as well as assessing the driver's input and determining the road friction coefficient. This allows torque distribution to the rear axle to be perfectly adapted in any driving situation. In addition, both the ESC control processes and torque vectoring are incorporated into the Haldex coupling control process. This enables the software to anticipate the opening and closing of the Haldex coupling, thereby reducing the reaction time significantly. To utilise the potential of this new technology, quattro drive is coupled with Audi drive select (refer to page 54). Audi drive select can be used to select between different vehicle configurations, i.e. the modes. A specific Haldex coupling setup is assigned to each configuration.630_049Ride profile selector module E592ESC-OFF buttonauto/comfort The Haldex coupling setup matches the known driving behaviour and the quattro-typical traction of the Audi A3 (Type 8V). dynamic This setup provides more agile steering response. The coupling is engaged as soon as the driver steers into the corner, allowing it to react more quickly to the closing of the coupling when accelerating out of the corner. The result is a smaller decrease in torque in response to oversteer and load changes.efficiency This setup offers better fuel economy than the auto/comfort mode and thus reduces C02 emissions. The Haldex coupling is activated restrictively. There are no drawbacks for quattro drive – torque is distributed to the rear axle even before all-wheel drive is required. If necessary, the system will change over temporarily to auto/ comfort mode while accelerating, when the kick-down mode is activated or when the ESC-OFF button is pressed. In individual mode, the driver can choose a Haldex coupling setup independent of other vehicle systems.28 BackForwards Ξ ContentsControl unit for all-wheel drive J492There are various housings for the Haldex coupling. The versions are mainly differentiated by the reinforcing ribs and by the attachment points for the all-wheel drive control unit J492. The modified attachment points alter the mounting position of the control unit and thereby preserve installation space, which otherwise would have been reduced by the reinforcing ribs. For correct code letter assignments, refer to the ETKA electronic parts catalogue. Haldex coupling pump V181Selector mechanism Selector lever cable for actuating the park lockEmergency release mechanism630_048Manual gearbox and Audi drive select In models with manual transmission, an E is additionally displayed on the gearshift indicator in efficiency mode.As in the Audi A3 (Type 8V), the 6-speed double-clutch gearbox 0D9 is integrated into the engine's thermal management system. It supports the startstop system by means of software. The gearbox mechatronics control unit is integrated into the immobiliser system. If the gearbox or the mechatronics are replaced, it is necessary to program the mechatronics and activate the immobiliser. The diagnostic tester has a Replace mechatronics function for this purpose. Depending on engine type, the 6-speed manual gearboxes 02Q and 0FB with front-wheel drive will be available at market launch in addition to the 0D9 gearbox with quattro drive. The 0FB gearbox will also be available with quattro drive at a later date.Reference For more information about the 5th generation Haldex coupling and the thermal management system of the 0D9 gearbox, please refer to Self Study Programme 609 "Audi A3 ’13".29 BackForwards Ξ Contents6-speed double-clutch gearbox 0D9 – S tronicWhen the Audi TT (Type FV) is launched, the 0D9 gearbox will only be available with quattro drive. A front-wheel drive version will be available at a later date. The 0D9 gearbox matches the 6-speed double-clutch gearbox 02E which the VW Group has been using since 2003. Vehicles with quattro drive are equipped as standard with Audi drive select. In addition to well-known gearbox functions such as starter lock, selector lever lock, software shiftlock, parking lock, tiptronic mode and kick-down, this SSP explains in depth the selector mechanism, downhill assist, the launch control program and the start assist systems.Selector mechanismThe selector mechanism of the 0D9 gearbox has been adapted to the interior of the Audi TT. It is identical to that of the Audi A3 (Type 8V) in terms of its design and operating logic. In addition to the selector lever positions "P", "R", "N", "D" and "S", it is possible to shift gear manually in tiptronic mode using the selector lever or the shift paddles on the steering wheel. The gear selected and the active gear are displayed in the Audi virtual cockpit.630_052The parking lock emergency release mechanism can be accessed by unclipping the selector lever gaiter from the centre console and pushing the insulating foam to the side.630_053Freewheel modeTo activate the Freewheel mode, the efficiency mode must be selected and the selector lever must be in the "D" position. In efficiency mode, an E (for efficiency) is displayed instead of selector lever position D. Freewheel mode is all-software function. In Freewheel mode, provided that the conditions for system activation have been met, the active clutch is opened in overrun to interrupt power transmission to the engine. The vehicle coasts along without the engine braking function and utilises the energy of the vehicle (kinetic energy) while the engine continues to idle. In "Freewheel" mode, current gear indication is suppressed. In efficiency mode, gear shifts are performed at lower RPM. Together with the Freewheel function, this improves fuel economy and reduces CO2 emissions. During the freewheel phase, the gears appropriate to the actual speed of the vehicle are preselected in order to provide a comfortable gear shift when the clutch closes. When the freewheel phase ends, engine speed is actively adjusted to synchronisation speed before the clutch responsible for the relevant gear is closed. Switch-on conditions: • Vehicle speed between 20 kph and 130 kph. • Accelerator position 0 % (the active clutch is opened directly after the 0 % accelerator position is detected and the last gearshift has been completed). • Gradient less than 8 % (the gradient is measured by the longitudinal acceleration sensor of the brake electronics). Switch-off conditions • Brake applied • TIPminus is selected on the tiptronic steering wheel. • The selector lever is moved out of "D". • Activation of the cruise control system (it does not constitute a switch-off condition if the cruise control system is switched on but not activated). • A gradient of greater than 15 % • If the vehicle speed is higher than the set speed of the cruise control system on a downhill gradient.Reference For more information about the selector mechanism and the emergency release mechanism of the selector lever, please refer to Self Study Programme 609 "Audi A3 ’13".30 BackForwards Ξ ContentsDownhill assistThe downhill assist functions aids the driver on downhill gradients. In selector lever positions "D" and "S", it is activated when the brake pedal is depressed or when the speed is set in vehicles with a cruise control system. Downhill assist tries to maintain the reduced speed within the bounds of physical and drive limitations. The gearbox selects a gear appropriate to the gradient. It may be necessary to additionally correct the vehcile's speed with the footbrake. Given that downhill assist shifts down into no lower than 3rd gear, it is advisable to switch to tiptronic mode on very steep gradients. This allows the vehicle to be shifted manually into 2nd or 1st gear to make use of the engine braking effect and relieve the load on the brakes. Downhill assist cuts out again as soon as the gradient lessens or the accelerator pedal is depressed.Launch control programThe launch control programme enables maximum acceleration. Conditions: • The engine is at operating temperature. • The wheels and the steering wheel are in the straight-ahead position. • The start-stop system is deactivated. • Start assist is deactivated. • The ESC-OFF button was briefly pressed once while the engine was running. • Selector lever is in the "S" position or in the tiptronic gate or dynamic mode is selected using Audi drive select. • Depress the brake pedal firmly for 1 second and hold it down. • Depress the accelerator pedal fully and hold it down. • Ease off the brake. After using the launch control program, the gearbox temperature may have risen sharply. In this case, the program may not be available for several minutes. After a cooling phase, the program will again be available. The launch control program puts maximum strain on parts of the drivetrain, resulting in increased wear.Hill start assist systemsThe hill start assist systems utilise the capabilities of the ESC system and the parking brake. They assist the driver by stopping the vehicle from inadvertently rolling away. Hill start assist and integrated start assist are standard. Start assist is optional. The requirements for system operation are that the driver's door is closed, the driver's seat belt is fastened and the engine is running. Hill start assist is available when the brake pedal is depressed at a gradient of about 5 % or steeper. When the vehicle halts on a gradient, the current brake pressure is maintained by the ESC control valves. If the brake pedal is released in order to drive away, this brake pressure is maintained for about 1.5 seconds. As soon as enough drive torque is available to move the vehicle, the brake is released. This function aids starting on gradients because the vehicle is largely prevented from rolling back. Hill start assist is also available in reverse gear. Integrated start assist is effective when the parking brake is actuated. It is opened at drive-away as soon as enough drive torque is available to set the vehicle in motion. Integrated start assist is only operational when the driver's seat belt is fastened. Start assist is a combination of hill start assist and integrated start assist. The system is activated by a button in the centre console and operates independently of time and gradient. Initially, the brake pressure applied when stopping is maintained by the ESC control valves. Due to the current draw of the ESC control valves, they heat up. To ensure that the max. allowable temperature of the valves is not exceeded, the system actuates the electrical parking brake autonomously. The parking brake can now maintain the brake pressure continuously. It is released automatically at drive-away as soon as sufficient drive torque is available to set the vehicle in motion. The following condition applies to integrated start assist and hil start assist: As long as the electrical parking brake is effective, the "creep" which vehicles usually exhibit is suppressed.31 BackForwards Ξ ContentsChassisOverall conceptOne key focus of development work on the chassis of the Audi TT was on achieving sporty driveability combined with dynamic and highly precise handling. This was achieved through a highly engineered suspension system with a front axle based on the McPherson concept and a newly developed four-link rear axle. The customer can choose between standard suspension, sport suspension and suspension with electronic damper control. In keeping with the sporty basic setup, use is made of progressive steering as standard. Torque vectoring also makes a major contribution excellent handling. The use of generously sized brake systems with vented brake discs at the front and the electromechanical parking brake at the rear underscore the sporty overall concept.630_082The following suspension variants are available for the Audi TT:Suspension/steering versions Standard suspension (1BA) Sports suspension (1BV)1) Suspension with electronic damper control (1BL)1) Sports suspension with electronic damper control (2MV)1) Suspension with electronic damper control (1BQ)1)1)Features The standard suspension as basic equipment features steel springs and unregulated damping. Sports suspension is optional. Models with sports suspension ride 10 mm lower than models with standard suspension and have a distinctly sporty setup. This suspension variant is also optional. It is based on the Audi magnetic ride system currently featured on other Audi models. The ride height is identical to that of the standard suspension. The sports suspension with electronic damper control (same technology as 1BL) has the same ride height as the non-regulated sports suspension (1BV). This suspension has been set up specially for the Audi TTS and is standard equipment. The ride height is identical to that of sports suspension 2MV.1)Production control number32 BackForwards Ξ ContentsAxles and wheel alignmentFront axleThe front axle is based on the Modular Transverse Platform (MQB). The McPherson concept which has proved successful in the predecessor model (Type 8J) has also been adopted for the Audi TT. To achieve a high level of driving dynamics, the Audi TT has special suspension setups.Spring • Steel spring with linear characteristic • TT-specific setupTie rod • Steel construction with plastic ball jointsDamper • 2-tube damper with polyurethane auxiliary spring • TT-specific setup • Low-friction axial bearingAnti-roll bar • Tubular anti-roll barsPivot bearing • Aluminium constructionJoint • Ball joint as link between track control arm and pivot bearingEngine/gearbox mount • Aluminium constructionTrack control arm • Aluminium constructionWheel bearing/wheel hub • 3rd generation wheel bearing with integrated wheel hub630_08333 BackForwards Ξ ContentsRear axleThe rear axle is also based on the Modular Transverse Platform (MQB). The proven multi-link axle concept for vehicles with frontwheel drive and quattro drive was adopted from the predecessor model (Type 8J) for the Audi TT.Upper track control arm • Steel constructionSpring link • High-tensile steel constructionDamper • 2-tube damper with polyurethane auxiliary spring • TT-specific setupWheel carrier • Aluminium castingSpring • Steel spring with linear characteristic • TT-specific setupTrailing arm • Steel constructionTie rod • Plastic part (not shown)Anti-roll bar • Tubular anti-roll barsWheel bearing/wheel hub • 3rd generation wheel bearing with integrated wheel hubMounting bracket • Steel constructionEngine/gearbox mount • Steel construction • Rigid body attachment for front-wheel drive models • Elastic connection for models with quattro drive, achieved using rubber-metal bearingTrack link • Steel construction630_08434 BackForwards Ξ ContentsWheel alignment and suspension setupThe left and right toe-in values on the front axle can be adjusted separately by changing the length of the track rods. The camber can be balanced (centred) within narrow limits by shifting the subframe transversely. Individual toe values and individual camber values can be adjusted on the four-link rear axle.Camber adjustmentToe adjustment at the attachment point between the spring link and subframe (not shown)630_084Toe adjustmentCamber balancing630_08335 BackForwards Ξ ContentsSuspension with electronic damper control (1BL, 1BQ, 2MV)The optional electronic damper control is based on the Audi magnetic ride system previously available for the predecessor model (Type 8J).Rear left vehicle level sender G76Shock absorber with damping adjustment valve, front left N336 Control unit in dash panel insert J285 Front left vehicle level sender G78630_089Rear right vehicle level sender G77ECD control unit (electronically controlled damping) J250Shock absorber with damping adjustment valve, front right N337 Front right vehicle level sender G289Shock absorber with damping adjustment valve, rear left N338Shock absorber with damping adjustment valve, rear right N339Reference For more information about the design and general functional principle of Audi magnetic ride, please refer to Self Study Programme 381 "Audi TT Coupé ’07 - Suspension".36 BackDamping characteristic 3 different damping characteristics are implemented in the Audi TT. They can only be set by selecting the relevant mode in Audi drive select (refer to page 54). Depending on preference, the driver can choose between comfortable (comfort), sporty (dynamic) and balanced (auto) damping characteristics.Forwards Ξ ContentsIf efficiency is selected, the auto damper control mode is implemented. Depending on the degree of damping, the coils in the damper pistons are activated by the output stages of the control unit by applying up to about 5 A of electrical current (max. damping). The damper is not permanently activated when the vehicle is stationary (speed signal = 0).Vehicle: Audi drive selectefficiency comfort auto dynamic individual630_096Special functionsTemperature model As with the predecessor model, a special software is also used here to make allowance for the temperatures of the dampers, the magneto-rheological fluid as well as the coils in the damper pistons and the electrical wiring. This software has been improved so that the influence of temperature can be determined even more exactly and that the damper-specific activation currents can be set even more precisely. The basic procedure is identical to that described in Self Study Programme 381 "Audi TT Coupé ’07 - Suspension". The base resistance value is now determined for each coil after turning on the ignition ("terminal 15 on") if the vehicle has been parked for at least 3 hours. After this downtime, the above-mentioned damper components will have reached ambient temperature, allowing an exact measured value for ambient temperature to be used an initial value for the temperature model. During the downtime of the vehicle and "terminal 15 on", the control unit sends a cyclic diagnostic pulse (about 2 A, duration of a few milliseconds, about once a second) to the damper coils to measure the resistance of the coil resistors. The temperature model determines the temperature of each damper from these resistance values. If the vehicle is parked for less than 3 hours with "terminal 15 off", the control unit determines the damper temperatures after "terminal 15 on" on the basis of the last temperatures to be calculated before turning off the ignition ("terminal 15 off"), while also taking into account the actual downtime of the vehicle.630_097Temperature monitoring and temperature shut-off If the measured damper temperature exceeds a value of about 110 °C, the dampers are gradually de-energised in order to protect the electrical and mechanical components. The dampers are fully de-energised at about 120 °C. This situation is extremely rare and occurs only if the dampers have been subjected to excessive excitation for a prolonged period of time with the result that they have had to perform a significant amount of damping work (accompanied by an increase in damper temperature). The temperature of the control unit is also monitored and factored into the temperature model calculation. The components and the wiring in the control unit heat up due to the permanent availability of activation currents during vehicle operation. If a temperature of about 120 °C is exceeded, the auto mode is activated. A different mode can no longer be selected by the driver. If the temperature drops below a value of about 100 °C, full system availability will be restored.37 BackSystem behaviour in response to fault As a fully integrated system, the damper control system has self-diagnostic capability. Any detected system faults are indicated to the driver by a fault message in the dash panel insert. Depending on the nature of the fault, the system response can range from a partial shut-down to a full shut-down of the system. If a damper can no longer be activated electrically, this does not affect the activation of the other 3 intact dampers. However, the driver can no longer change to a different mode, and the dampers are controlled in auto mode. If ESC has been deactivated by the driver, then it is activated automatically in these cases. The same system response is triggered when a fault is detected in a ride height sensor and the measured data from this sensor is no longer available. In the event of failure of 2 dampers, the system is shut down. In this case, corrective actions are no longer performed. If ESC has been deactivated by the driver, it is then activated automatically. The same system response occurs when a fault is detected in a ride height sensor and the measured data from this sensor is no longer available. If it is no longer possible to electrically activate the dampers (e.g. due to relevant control unit faults), then the smallest possible damping forces will be produced by the dampers. Although the suspension setup is very comfortable, handling remains stable in driving dynamics terms.Forwards Ξ ContentsDamper control Fault! You can continue driving630_103Service operationsDiagnostic address The system can be accessed in the diagnostic tester under address 14 - wheel damping. Control unit J250 is integrated into the component protection system.630_099System initialisation – Learn control position System initialisation is performed after: • replacing control unit J250 • removing or replacing one or more vehicle level senders • replacing or removing and installing the dampers The characteristics of the vehicle level senders are stored in the control unit. When the system is initialised, the control unit is informed which actual vehicle ride levels at the wheel positions correspond to the measured data supplied by the vehicle level senders. If this assignment is known to the control unit, all the following measured data from the vehicle level senders can be converted to actual vehicle ride levels. In addition, the unladen height of the vehicle is stored in the control unit.630_10038 BackActuator diagnostics Selective activation of dampers is possible using the actuator diagnostics routine. The dampers are then energised with an electrical current of about 2 A.Forwards Ξ ContentsCold starting This function, which can be activated with the diagnostic tester, basically comprises the same routine which the control unit performs automatically when terminal 15 is switched on after a vehicle downtime of at least 3 hours. The dampers are energised and the resistance values of the coils in the damper pistons are determined. These resistance values are then assigned to the measured ambient temperature. This assignment now provides the basis for the temperature calculation by the temperature model. After replacing the control unit, the cold start function should always be executed because the new control unit still does not know the resistance values of the damper coils. It also makes sense to perform the function if one or more dampers have been replaced. For tolerance reasons, the coils of the new dampers have different resistance valves than those already stored in the control unit. However, a condition for this is that the new dampers have approximately ambient temperature. If the function is not executed, loss of comfort may subsequently occur while driving. The next time the vehicle is started (after a downtime of at least 3 hours), the coil resistances are defined automatically by the system and the desired level of ride comfort is again ensured.Damper test The damper test on a corresponding test bench is automatically detected by a special test mode. Alternatively, the test mode can also be activated manually using the diagnostic tester. Test bench operation is detected automatically by evaluating the measured data supplied by the vehicle level sender. If vertical oscillation of the wheels on an axle is determined within a defined frequency band, the test mode is activated. The relevant dampers are activated by the control unit with a constant current of about 1 A in order to achieve defined damping