TECHNICAL DOCUMENTATION

SSP 634 Audi Q7 (type 4M) Onboard power supply and networking

PDFEN72 pages12 MB
SSP 634 Audi Q7 (type 4M) Onboard power supply and networking - PDF cover

This PDF is currently unavailable.

Read document text
Self Study Programme 634 For internal use onlyAudi Q7 (type 4M) Onboard power supply and networkingAudi Service Training BackThe number of electronic control units has grown rapidly in recent years. Most of today's innovations have only been made possible by the increasingly higher performance of the electronic systems. It is particularly worth mentioning the rising number of driver assist systems, innovative light technology and, of course, the rapid development in the infotainment sector. Without that development, many in-car comforts and conveniences that are now taken for granted would not have been achievable. When the Audi Q7 (type 4M) is compared with its predecessor, the Audi Q7 (type 4L), there are the following striking differences: • The number of control units has increased from about 60 to 120. • The number of control units which use the bus systems has risen sharply, particularly the number of LIN control units. • In-car data transfer rates have quadrupled.Forwards Ξ ContentsThe Audi A3 (type 8V) and TT (type FV) models are representatives of the so-called MQB (Modular Transverse Platform). The Audi A6, A7 and A8 belong to the MLB (Modular Longitudinal Platform). The structure of the onboard power supply within a platform is, apart from equipment-related differences, always the same. The Audi Q7 (type 4M) is the first representative of the MLBevo (Modular Longitudinal Platform Evolution). Its new onboard power supply structure therefore replaces that of the MLB. The first part of this self study programme summarises the onboard power supply of the Audi Q7 and provides information on the functions, installation locations and specific features of numerous control units. The design and function of the various headlight and tail light versions are described in "Exterior lighting". This is a quick and direct way to obtain an in-depth knowledge of the electrical and electronic equipment in the Audi Q7.634_002Learning objectives of this self study programme: Once you have completed this self study programme you will be able to answer the following questions: • Where are the fuseholders located in the Audi Q7 and what are their designations? • In what locations are electrical components fitted on the car? • Which bus systems are used on the Audi Q7? • What are the tasks of the control units in the car? • What are the versions of the exterior lighting and how are the individual light functions implemented? • What changes have been made regarding headlight range adjustment and calibration of the Audi Matrix LED headlights?2 ContentsVoltage supplyCar battery ____________________________________________________________________________________________________________________________________________________ Jump start terminal __________________________________________________________________________________________________________________________________________ Supply structure _ _____________________________________________________________________________________________________________________________________________ Fuses and relays ______________________________________________________________________________________________________________________________________________ 4 5 6 7Network systemInstallation locations of control units _____________________________________________________________________________________________________________________ 8 Topology _____________________________________________________________________________________________________________________________________________________ 10 Bus systems used on the Audi Q7 _________________________________________________________________________________________________________________________ 12 FlexRay _______________________________________________________________________________________________________________________________________________________ 13 Optical data bus system MOST150 ________________________________________________________________________________________________________________________ 16Control unitsBrief descriptions ___________________________________________________________________________________________________________________________________________ 18Exterior lightsHeadlight variants __________________________________________________________________________________________________________________________________________ 54 Xenon headlight _____________________________________________________________________________________________________________________________________________ 56 LED headlights ______________________________________________________________________________________________________________________________________________ 58 Audi Matrix LED headlight _ ________________________________________________________________________________________________________________________________ 60 Tail lights ____________________________________________________________________________________________________________________________________________________ 62 Sequential flashing _________________________________________________________________________________________________________________________________________ 64 High-level brake light / number plate lights _____________________________________________________________________________________________________________ 65Start-stop systemStart-stop system version 2.0 _____________________________________________________________________________________________________________________________ 66Audi drive selectFunctional characteristics __________________________________________________________________________________________________________________________________ 68 Displays and operation _____________________________________________________________________________________________________________________________________ 68 Driving modes _______________________________________________________________________________________________________________________________________________ 69 Controllable systems _______________________________________________________________________________________________________________________________________ 69 Audi drive select function __________________________________________________________________________________________________________________________________ 70AppendixSelf study programmes _ ____________________________________________________________________________________________________________________________________ 71The self study programme teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a repair manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. This content is not updated. For further information on maintenance and repair work, always refer to the current technical literature.NoteReference3 BackForwards Ξ ContentsVoltage supplyCar batteryThe car battery in the Audi Q7 is built into the underbody in front of the right seat. Depending on the car's equipment specification, use is made of different battery sizes and types matched to the car. Only AGM batteries1) are used. Attached to the battery positive terminal is the main fuseholder and the battery isolation igniter N253, which is often referred to as the battery isolator element. If the battery isolation igniter is activated in a crash, the alternator, the starter, the automatic glow period control unit, the secondary air pump relay and the radiator fan are disconnected from terminal 30, i.e. de-energised. The battery monitoring control unit J367 is attached to the negative terminal of the car battery. This control unit and the ground line form a unit. The term battery data module (BDM) is sometimes used for J367. The car battery test must be performed using the diagnostic tester, especially during the warranty period. A test program in the Guided Fault Finding system checks not only the voltage and internal resistance of the battery, but also evaluates the history data of the car battery. Thus, it is possible to include the age of the car battery and any general voltage undershoots which have occurred to be incorporated into the assessment of the car battery. To allow such an assessment to be made, the new car battery must be adapted to the battery monitoring control unit J367 after installation.Battery monitor control unit J367Battery A634_012Main fuseholder and battery isolation igniter N253AGM batteryIn the case of AGM batteries, the battery electrolyte is absorbed in a glass microfibre mat. In addition to having higher deep-cycle resistance, the AGM battery is noted for its leak-proof design. Leak proofing is of course very important when installing the battery inside the car. When charging an AGM battery, it is important to follow the charger's operating instructions and, where applicable, to program the charger for AGM batteries. The following AGM batteries are used on the Audi Q7: • • • • • 68 Ah/380 A 75 Ah/420 A 92 Ah/520 A 92 Ah/520 A 105 Ah/580 A1)English: Absorbant Glass Mat4 BackForwards Ξ ContentsJump start terminalThe jump start terminal is located in the engine bay on the righthand side of the car between the coolant reservoir and the plenum chamber. This connection can also be used for charging the car battery in the showroom or for purposes of diagnostic work in the workshop.Distributor TV22 with fuses Distributor TV2Interference suppression capacitor C24Jump start terminal Terminal 30 supplyStarter/alternator cable634_013The actual jump starting terminal is located on the terminal 30 distributor TV2. The red 70-mm2 cable supplies the distributor. The 3 fuses on distributor TV22 protect the radiator fan, the glow plugs and the secondary air pump.The black 70-mm2 cable leads to the starter, where are further cable leads to the alternator. The interference suppression capacitor C24 is located adjacent to distributor TV2.5 BackForwards Ξ ContentsSupply structureThis diagram summarises the supply structure of the Audi Q7. This is a schematic diagram. For precise details of fuse assignment and cable routing, please refer to the relevant service literature.TV22TV2 SCTV1SBSF634_003Key: 1 2 3 4 5 6 A B C 6Connection to auxiliary air heater control unit J604 Connection to control unit for windscreen heater J505 Connection to rear axle steering control unit J1019 Connection to automatic glow period control unit J179 or secondary air pump relay J299 Connection to radiator fan control unit 2 J671 Connection to radiator fan control unit J293 Battery Starter motor AlternatorJ367 Battery monitor control unit J500 Power steering control unit N253 Battery isolation igniter SB Fuseholder B, on the footrest SC Fuseholder C, on the dash panel SF Fuseholder F, in luggage compartment on L/H side TV1 Distributor, near car battery TV2 Distributor for terminal 30 TV22 Distributor 2 for terminal 30 BackForwards Ξ ContentsFuses and relaysThe fuses on the main fuseholder as well as distributors TV1 and TV22 are labelled only "S" in the current flow diagram. This also applies to other individual fuses distributed throughout the car. Fuses "SB", "SC" and "SF" can also be accessed by the driver on the relevant fuseholders, and therefore are also described in the Owner's Manual.Relay and fuseholder 1 "SR1"Distributor for terminal 30 TV2 and distributor 2 for terminal 30 TV22 with fusesDistributor for terminal 30 TV1 with fusesMain fuseholder on the battery634_014Fuseholder B on the driver side footrest. The fuses here are labelled "SB" in the current flow diagram.Fuseholder C on the dash panel, driver side. The fuses here are labelled "SC" in the current flow diagram.Fuseholder F in the luggage compartment, rear left. The fuses here are labelled "SF" in the current flow diagram.7 BackForwards Ξ ContentsNetwork systemInstallation locations of control unitsSome of the control units shown in the overview are optional and/ or country-specific equipment. For reasons of clarity, not all control units fitted in the car can be shown here. Refer to the current service literature for details of controls unit positions as well as instructions for installation and removal.J428 J364 J1023J505J387A27J794J844 J500 J869 J685 E87 R242E380 J775 J587 J853 J533 J234J764 J898 J285 J527J623 A31 J104J1018J519J850J386Key: A27 Right LED headlight power module 1 A31 Left LED headlight power module 1 E87 Front air conditioner/Climatronic operating and display unit E265 Rear air conditioner/Climatronic operating and display unit E380 Multimedia system operating unit J104 ABS control unit J136 Seat and steering column adjustment control unit with memory function J234 Airbag control unit J245 Sliding sunroof control unit J285 Instrument panel control unit J345 Trailer detector control unit8J364 J386 J387 J393 J428 J500 J502 J505 J519 J521 Auxiliary heater control unit Driver side door control unit Front passenger side door control unit Central control unit for comfort/convenience system ACC control unit Power steering control unit Tyre pressure monitor system control unit Control unit for windscreen heater Onboard power supply control unit Control unit for front passenger seat adjustment with memory function J525 Digital sound package control unit J527 Steering column electronics control unit J533 Data bus diagnostic interface BackForwards Ξ ContentsJ927J857R78 J880J769J521J1019J245E265J605J772J502 J136J525J345 J926 R161J928 J393J770634_005J587 J605 J623 J685 J764 J769 J770 J772 J775 J794 J844 J850 J853 J857 Selector lever sensors control unit Rear lid control unit Engine control unit MMI display Electrical steering column lock control unit Lane change assist control unit Lane change assist control unit 2 Reversing camera system control unit Chassis control unit Information electronics control unit 1 Main beam assist control unit ACC control unit 2 Night vision system control unit Seat adjustment control unit, 3rd seat rowJ869 Structure-borne sound control unit J880 Reducing agent metering system control unit J898 Control unit for windscreen projection (head-up display) J926 Door control unit, rear driver side J927 Door control unit, rear passenger side J928 Surround view camera control unit J1018 Control unit for light control, left J1019 Rear axle steering control unit J1018 Control unit for light control, right R78 TV tuner R161 DVD auto changer R242 Front camera for driver assistance systems9 BackForwards Ξ ContentsTopologyThe topology shows all control units with connectivity to the bus systems. Some of the control units shown here are optional or countryspecific equipment or are due for rollout at a later date.Flap control servomotors 1 ­ – 15Front air conditioner/Climatronic operating and display unit E87Rear air conditioner/Climatronic operating and display unit E265 Auxiliary air heater control unit J604 Flap control servomotors 1 ­ – 7Door control unit, rear driver side J926Driver side door control unit J386Ioniser, driver side J1105Door control unit, rear passenger side J927Front passenger side door control unit J387 Seat and steering column adjustment control unit with memory function J136Fresh air blower control unit J126Humidity sender in fresh air intake duct G657 Air quality sensor G238Rear ioniser, passenger side J1108Valve block 1 in driver seat N475Rear fresh air fan control unit J391Diagnostic port Flap control servomotors 1 ­ – 5 High pressure sender G65Valve block 2 in driver seat N476Valve block 1 in front passenger seat N477Control unit for front passenger seat adjustment with memory function J521Data bus diagnostic interface J533Valve block 2 in front passenger seat N478Control unit for electrically adjustable steering column J866 Trailer detector control unit J345 Seat back fan 1 + 2, front left V512 + V513 Garage door operating unit E284Multifunction steering wheel control unit J453 Light switch E1Articulation angle sensor for tow bar G820Seat adjustment control unit, 3rd seat row J857 Sliding sunroof control unit J245Seat cushion fan 1 + 2, front left V514 + V515 Seat back fan 1 + 2, front right V516 + V517Garage door opener control unit J530Wiper motor control unit J400Automatic anti dazzle rear view mirror Y7 Roof electronics control unit J528Rain and light detector sensor G397Rear lid control unit J605Seat cushion fan 1 + 2, front right V518 + V519 Onboard power supply control unit J519Humidity sensor G355Heated windscreen control unit J505Electronic steering column lock control unit J764 Alarm horn H12Anti-theft alarm sensor G578Rear hatch opening control unit J938Interior light moduleInterior light moduleCentral control unit for comfort/convenience system J393Key: Convenience CAN Hybrid CAN Extended CAN10Infotainment CAN bus Diagnostics CAN bus FlexRay BackFor presentation purposes, the FlexRay topology does not mirror the actual configuration of the control units. This also applies to the control units on the MOST bus.Forwards Ξ ContentsThis self study programme explains in detail the special features of the FlexRay bus (page 13) and MOST bus (page 16).Driver side volume control E67TV tuner R78Digital sound package control unit J525Multimedia system operating unit E380DVD changer R161MMI display J685Information electronics control unit 1 J794Control unit in dash panel insert J285Battery monitor control unit J367Alternator CSelector lever sensors control unit J587Control unit for windscreen projection (head-up display) J898Reducing agent metering system control unit J880 L/H control unit for light control J1018 Front camera for driver assistance systems R242 ABS control unit J104 Engine control unit J623 NOx sender control unit J583 Control unit for night vision system J853R/H control unit for light control J1023Radiator louvre control motor V544NOx sender control unit 2 J881Camera for night vision system R212Left LED headlight power module 1 A31Automatic gearbox control unit J217Steering column electronics control unit J527 ACC control unit 2 J850Particulate sensor G784Reversing camera system control unit J772orRight LED headlight power module 1 A27ACC control unit J428Structure-borne sound control unit J869Surround view camera control unit J928Rear axle steering control unit J1019Chassis control unit J775Auxiliary heater control unit J364Tyre pressure monitor system control unit J502 Main beam assist control unit J844Power steering control unit J500Adaptive suspension compressor motor V66 Airbag control unit J234Remote control receiver for auxiliary heater R64 Front left seat belt tensioner control unit J854 Front right seat belt tensioner control unit J855Operating unit 1 for drive and comfort/ convenience functions E791Audi side assist control unit J769Seat occupancy recognition control unit J706Audi side assist control unit 2 J770634_004Modular infotainment system (MIB) CAN LIN bus Sub-bus systemsMOST bus LVDS "OR" configuration11 BackForwards Ξ ContentsBus systems used on the Audi Q7Bus system Hybrid CAN Convenience CAN Extended CAN Infotainment CAN bus Modular infotainment system (MIB) CAN Diagnostics CAN bus FlexRay MOST bus Cable colour Configuration Electrical two-core bus system Electrical two-core bus system Electrical two-core bus system Electrical two-core bus system Electrical two-core bus system Electrical two-core bus system Electrical two-core bus system Fibre-optic bus system Max. data transfer rate 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 10 Mbit/s 150 Mbit/s Property Not single wire capable Not single wire capable Not single wire capable Not single wire capable Not single wire capable Not single wire capable Not single wire capable Ring structure: an open circuit leads to total system failure Capable of single-core operation Not single wire capable Not single wire capableLIN bus Sub-bus system LVDS1)Electrical single-core bus system Electrical two-core bus system Electrical two-core bus system20 kbit/s 500 kbit/s approx. 200 Mbit/sNew features of the bus systems in comparison with the predecessor, Audi Q7 (type 4L)Listed here are just a few examples: • The convenience CAN bus and infotainment CAN bus are high-speed bus systems • New MOST bus – MOST150 • The control unit in the instrument cluster J285 is a convenience CAN user • The data bus diagnostic interface J533 is the master of LIN slave J453 - multifunction steering wheel control unit • The data bus diagnostic interface is not a MOST bus user • The information electronics control unit 1 J794 is the system and diagnostic manager for the MOST bus • Information electronics control unit 1 J794 is connected to the CAN-MIB operating unit and display The network diagram on page 10 provides a schematic overview of the communication paths between the in-car control units. The control units which are actually installed on the car depend on the equipment specification. Listed here are just a few examples: • Main beam assist control unit J844 is never fitted in combination with front camera for driver assistance systems R242 • The seat occupancy recognition control unit J706 is only available in the North American market The number of LIN slaves of the control units is heavily dependent on the equipment specification. Not all versions can be shown in the networking diagram.LVDSThis data transfer system is notable for its relatively low voltage. As is the case with high-speed CAN bus systems, the differences in voltage are evaluated. In the case of LVDS, the voltage is approx. 0.3 V. A typical application of LVDS is the activation of liquid crystal monitors. In the Audi Q7 LVDS is used for image transfer between the surround view camera control unit J928, the information electronics control unit 1 J794 and the control unit in dash panel insert J285. The LVDS lines are sheathed, much like the FlexRay lines. By comparison to the FlexRay, the sheathing of the LVDS lines not only protects against mechanical stresses and moisture, but also shields against electromagnetic interference. In the event of a fault, LVDS lines must always be replaced complete.1)LVDS = Low Voltage Differential Signaling12 BackForwards Ξ ContentsFlexRayIntroduction634_015FeaturesThe FlexRay bus on the Audi A7 has the following features: • Electrical two-core bus system • Data transfer rate: max. 10 Mbit/s • Data transfer with three signal states: • "Idle" • "Data 0" • "Data 1" • "Active" star topology • Real-time capabilities • Enables distributed control and the use of safety-related systemsThe Audi Q7 utilises a FlexRay bus, a new data bus system originally launched on the Audi A8 (type 4H). What precisely is FlexRay? The FlexRay consortium, a cross-manufacturer development organisation, was established in 2000 and has since been joined by more members, including Volkswagen. What does FlexRay stand for? Flex = Flexibility Ray = Ray (i.e. the fish, as featured in the consortium's logo) The aim of using FlexRay is to meet the higher demands of future network systems in motor vehicles, in particular faster data transfer rates, real-time capability and failure-safety. It thus extends the range of possible uses such as for dynamic handling control, ACC active cruise control and image processing.Signal statesThe two cores of the FlexRay line are designated bus positive and bus negative. The voltage levels of both cables alternate between a minimum of 1.5 V and a maximum of 3.5 V. The FlexRay bus can have 3 signal states: • "Idle" – the level of both bus cable cores is 2.5 V • "Data 0" – the bus positive has a low voltage level and the bus negative a high voltage level • "Data 1" – the bus positive has a high voltage level and the bus negative a low voltage level One bit has a width of 100 ns. The transmission time is dependent on the cable length and the transition times through the bus drivers. The signals are transmitted by differential means, i.e. two cable cores are required. The receiver detects the actual bit status by means of the difference between the two signals. Typical signals are voltage differences of between 1.8 V and 2.0 V. A voltage differential of at least 1200 mV must be present directly at the sender. A voltage differential of at least 800 mV must be still be present at the receiver. If no activity takes place on the bus for 640 - 2660 ms, the FlexRay automatically enters sleep mode (idle).1 bit Differential voltage Time [ns]634_016 634_017 13Repairing a FlexRay lineThe FlexRay lines are twisted in the same way as the CAN lines. They are additionally sheathed. However, the sheathing does not provide shielding against electromagnetic interference, it merely minimises external effects such as damp and temperature on the core's characteristic impedance. In principle, sections of FlexRay lines can be replaced. When doing so, the untwisted length (1) and the unsheathed length (2) must be observed.Note For details of the precise procedure for repairing a FlexRay lead and which special tools are required, you should refer to the up-to-date repair guide on the ELSA system.Voltage [V] BackForwards Ξ ContentsControl units on the FlexRay busThe data bus diagnostic interface J533 is the controller for the FlexRay bus. All FlexRay control units are connected to J533 within various branches. In this configuration J533 is referred to as the "active hub" or "active node". If only one control unit is connected within a branch, this is referred to as a "point to point" connection. If more than one control unit is connected within a branch, this is referred to as a "daisy chain connection". In the Audi Q7 six branches are assigned: branches 1 – 5 and branch 8. The pins of branches 6 and 7 are reserved in the current version of J533, but are still not assigned. The first figure is a schematic diagram showing how the control units are connected.ABS control unit J104Power steering control unit J500Steering column electronics control unit J527Engine control unit J623Automatic gearbox control unit J217Front camera for driver assistance systems R242Chassis control unit J775Branch 1Data bus diagnostic interface J533Branch 2Branch 3Branch 4Branch 5ACC control unit 2 J850Branch 8Airbag control unit J234ACC control unit J428Rear axle steering control unit J1019 634_006Reference For further information about the FlexRay bus, refer to Self Study Programme 459 "Audi A8 ’10 Onboard power supply and networking".14 BackForwards Ξ ContentsAs regards the configuration of the control units, Fig. 2 differentiates between the bus positive cable (pink) and the bus negative cable (green) and thus represents the actual situation. Two resistors each having a resistance of 47 Ω, i.e. 94 Ω in total, are connected to end of each branch in the control unit. Each of the so-called "centre control units" has two resistors with a resistance of 1.3 Ω, i.e. 2.6 Ω in total. These values – 94 Ω and 2.6 kΩ – can be measured on each of the control units with a multimeter after disconnecting the control unit plug.A short circuit to positive or ground within a branch will cause the entire branch to fail. However, the other FlexRay branches continue to function. If a FlexRay connection is broken, all control units downstream of the open circuit are cut off from communications. If a "centre control unit" is de-energised, it no longer participates in communications. However, the downstream control units can still participate in communications as long as the signals are looped through to the PCB of the "centre control unit".J10447 Ω 47 ΩJ50047 Ω 47 ΩJ52747 Ω 47 ΩJ6231,3 kΩ 1.3 kΩJ2171,3 kΩ 1,3 kΩR2421,3 kΩ 1,3 kΩJ7751,3 kΩ 1,3 kΩBranch 147 Ω 47 Ω 47 Ω 47 ΩBranch 2J53347 Ω 47 Ω 47 Ω 47 ΩBranch 347 Ω 47 Ω 47 Ω 47 ΩBranch 4Branch 5Branch 81,3 kΩ1,3 kΩJ85047 Ω47 Ω47 Ω47 Ω1,3 kΩ1,3 kΩJ234J428J1019634_00715 BackForwards Ξ ContentsOptical data bus system MOST150634_060HistoryFor the first time in an Audi, an optical data bus system - the MOST bus - is fitted on the Audi A8 (type 4E). This data bus system is named after the "Media Oriented Systems Transport (MOST) Cooperation". This organisation is made up of various automobile manufacturers, their components suppliers and software companies which joined forces to create a standardised high-speed data transfer system. The term "Media Oriented Systems Transport" denotes a network with media-oriented data transport. This means that, unlike in the CAN data bus, address-oriented messages are sent to a specific recipient. This technology is used in Audi cars to transfer data within the infotainment system. The data transfer rate on the MOST25 bus is approx. 25 Mbit/s.MOST150The MOST150 is used on the Audi Q7 for the first time in an Audi Q series car. The data transfer rate of this evolution in MOST technology is six times faster than the MOST25 bus. The development process necessitated making various modifications to the components of the MOST bus. For instance, the transmitter and receiver units – Fiber Optical Transmitters (FOT) – had to be adapted. Other components such as the optical connectors, the fibre optics and the electrical connectors of the control units are identical to those of the MOST25.System managerIn the Audi Q7 up to 5 control units are integrated in the MOST ring in the following order: • • • • • Information electronics control unit 1 J794 DVD changer R161 Control unit in dash panel insert J285 Digital sound package control unit J525 TV tuner R78 In the Audi Q7 the information electronics control unit 1 J794 acts not only as the system manager for the MOST bus, but also as the diagnostic manager - a function previously performed by the data bus diagnostic interface J533 in the Audi Q7 (type 4L). As always with a MOST bus on Audi cars, the control units are interconnected by an electronic ring break diagnostics line. This line is only required for electronic ring break diagnostics in the event of a fault.Reference For further information on the MOST bus, refer to self study programme 286 "New Data Systems – LIN, MOST, BluetoothTM".16 BackRing break diagnosticsForwards Ξ ContentsDriver side volume control E67TV tuner R78Digital sound package control unit J525Multimedia system operating unit E380Ring break diagnostics lineInformation electronics control unit 1 J794DVD changer R161MMI display J685Control unit in dash panel insert J285Key: Infotainment CAN bus Modular infotainment system (MIB) CAN LIN bus MOST bus LVDS634_011Optical replacement control unit VAS 6778Diagnostics The ring break diagnosis procedure is identical to that of the previous MOST bus system. However, the inspection plan for the Audi Q7 has to be retrieved from the diagnostic tester using address word 5F. Even though the ring break diagnosis procedure remains unchanged, a modified tool – the optical replacement control unit VAS 6778 – must be used in the event of an optical fault in the MOST150 bus, due to the modified transmitter and receiver units in the control units.634_01817 BackForwards Ξ ContentsControl unitsBrief descriptionsOnboard power supply control unit634_020Connector C (54-pin) to cockpit wiring loomConnectors A and B (each 73-pin) to car / engine bay18 BackDesignation Equipment Installation location Tasks Onboard power supply control unit J519 / also referred to as BCM1 (Body Control Module 1) Always fitted On A post, L/H side, above bonnet release lever (Installation location is always on L/H side, even in RHD models) Exterior lighting master Interior lighting master Diagnostic gateway for the light control unitsForwards Ξ ContentsA/C functions • Activation of seat heater and front seat ventilation • Activation of air conditioning compressor without regulating valve N280 and solenoid coupling for air conditioning system N25 Integration functions • Parking • Park assist • Park assist steering • Activation of front and rear acoustic signal generators • Background light • Activation and supply of LIN interior light modules • Trailer assist • Steering assistance during reversing with a trailer • Read-in of the bend angle sensor • Headlight range adjustment • Calculation of headlight range adjustment • Activation of headlight range adjustment via the left and right control units for light control J1018 and J1023. • Read-in of the signals from the inclination sensor via the CAN line Other functions • Reading in the following senders/sensors/switches: • Ambient temperature • New engine coolant, windscreen washer fluid, brake fluid • Brake pad wear • Bonnet contact • Seater heater temperature • Activating the following actuators/control elements: • Relay for sockets • Signal horn • Headlight washer system • Windscreen washer pump (dual pump) • Heating the windscreen washer jets • Seat heater, front Diagnostic address Data bus communication 09 • Convenience CAN user • J519 is the LIN master for: • LIN 1: Light switch E1; wiper motor control unit J400; combined sensor – rain and light detection sensor G397 and humidity sender G355 • LIN 2: Garage door operating unit E284; Garage door operation control unit J530; automatic anti dazzle rear view mirror Y7; roof electronics control unit J528 • LIN 3: Electrically adjustable steering column control unit J866; seat back fans 1 and 2, front left and right V512/V513 and V516/V517; and seat cushion fans 1 and 2, front left and right V514/V515 and V518/V519 • LIN 4: Operating unit 1 for drive and comfort/convenience functions E791 • LIN 5: Interior light module • LIN 6: Interior light module • Communicates via a sub-bus system with the L/H and R/H control units for light control J1018 and J1023 and left and right LED headlight power modules 1 A31 and A27 Fault finding notes: With regard to the LIN slave configuration, J519 has duplicated pins. For example, LIN 1 are distributed to 3 pins (A22, A23,C50) which are connected internally within the control unit. This means that the control units connected to pin A23 and C50 are also affected in the event of a short circuit to positive or negative at pin A22, and vice versa.Special feature19 BackForwards Ξ ContentsGatewayDesignation Equipment Installation location Tasks Data bus diagnostic interface J533 Always fitted Under seat, front left, on floor panel • • • • • 19 • Hybrid CAN, convenience CAN, Infotainment CAN, CAN-Extended and FlexRay user • LIN master of battery monitor control unit J367 and alternator C • LIN master for multifunction steering wheel control unit J4531) • Not a modular infotainment system (MIB) CAN user • Not a MOST bus user Network system gateway Controller for FlexRay bus Diagnostic master Energy management control unit Coordinator for drive selectDiagnostic address Data bus communicationSpecial features634_019Data bus diagnostic interface J5331)Optional equipment20 BackForwards Ξ ContentsCentral control unit for comfort/convenience systemDesignation Equipment Installation location Central control unit for comfort/convenience system J393 / also referred to as BCM2 (Body Control Module 2) Always fitted In luggage compartment, L/H side, behind luggage compartment side trim, below fuse and relay panel "SF" (Installation location is always on the L/H side, even in RHD models) Central locking system master Integration functions • Terminal control unit • Entry and start authorisation • Immobiliser (master) • Anti-theft alarm system Other functions • Reading in the following senders/sensors/switches: • Brake light switch • Ignition starter button • P signal • Soft touch button on rear hatch • Rear hatch contacts (prelock and full lock) • Rear window breakage sensor • Switches for tail light switchover 1 and 2 • Capacitive sensors of door handles • Entry and start authorisation aerials • Fuel tank sender • Inclination sensors for headlight range adjustment • Hall effect sensor, rear roller blind • Activating the following actuators/control elements: • Rear hatch lock motor • Luggage compartment release • Fuel tank flap lock • Rear roller blind motor • Terminal 15 relay • Heated rear window relay • Rear wiper relay • Rear hatch opening control unit supply voltage • Luggage compartment lights • Rear lighting Diagnostic address Data bus communication 46 • Convenience CAN user • J393 is the LIN master for: • LIN 1: Control unit for windscreen heater J505; antitheft alarm system sensor G578 • LIN 2: Alarm horn H12 • LIN 3: Boot lid opening control unit J938 • J393 is the immobiliser master in the Audi Q7; address word 05 is no longer used for the immobiliser. • Central locking aerial is integrated in the control unit PCBTasksSpecial featuresCentral control unit for comfort/convenience system J393634_021 21 BackForwards Ξ ContentsDriver side door control unitDesignation Equipment Installation location Tasks Driver side door control unit J386 Always fitted In driver's door Controlling the electrical and electronic components in and on the driver's door • Reading in the following senders/sensors/switches: • Switches/buttons, e.g. for: Window lifters, fuel tank flap release, rear hatch release, electrical child lock button, electrical door mirror, central locking, seat memory etc. • Activating the following actuators/control elements: • Lights and components in and on the door trim, locking and safe motor, turn signals in door mirror 42 • Convenience CAN user • LIN master for door control unit, rear driver side J926 Door control unit, rear driver side J926 has its own address word "BB" although it is a LIN slave of J386.Diagnostic address Data bus communication Special featureDriver side door control unit J386634_022Front passenger side door control unitDesignation Equipment Installation location Tasks Front passenger side door control unit J387 Always fitted In front passenger's door Controlling the electrical and electronic components in and on the front passenger's door • Reading in the following senders/sensors/switches: • Switches/buttons, e.g. for: Window lifters, rear hatch release, electrical child lock button, electrical door mirror, central locking, seat memory etc. • Activating the following actuators/control elements: • Lights and components in and on the door trim, locking and safe motor, turn signals in door mirror 52 • Convenience CAN user • LIN master for door control unit, rear passenger side J927 Door control unit, rear passenger side J927 has its own address word "BC" although it is a LIN slave of J387.Diagnostic address Data bus communication Special feature22 BackForwards Ξ ContentsSliding sunroof control unitDesignation Equipment Installation location Tasks Sliding sunroof control unit J245 Optional equipment (PR no.: 3FU) On sliding sunroof frame at front Controlling the functions of the panoramic glass sunroof • Reading in the following senders/sensors/switches: • Controller for sliding sunroof adjustment • Activating the following actuators/control elements: • Motors for sliding sunroof V1 and sliding sunroof roller blind V260 CA Convenience CAN userDiagnostic address Data bus communication634_026Sliding sunroof control unit J24523 BackForwards Ξ ContentsSeat adjustmentDesignation Equipment Installation location Tasks Seat and steering column adjustment control unit with memory function J136 Optional equipment (PR no.: PV3) Below the driver's seat Activating the following actuators/control elements: • Seat adjustment (memory function) • Steering column adjustment (memory function) • Valve blocks 36 • Convenience CAN user • LIN master for valve blocks 1 and 2 in driver seat N475 and N4761) • Valve block 1 in driver seat N475 controls the pneumatic lumbar support as well as seat side and seat back bolster adjustment1). • Valve block 2 in driver seat N476 controls the pneumatic cushions for the massage function1).Diagnostic address Data bus communication Special featuresSeat and steering column adjustment control unit with memory function J136634_023Designation Equipment Installation location TasksControl unit for front passenger seat adjustment with memory function J521 Optional equipment (PR no.: PV3) Below the front passenger seat (not shown) Activating the following actuators/control elements: • Seat adjustment (memory function) • Valve blocks 06 • Convenience CAN user • LIN master for valve blocks 1 and 2 in front passenger seat N477 and N4781) • Valve block 1 in front passenger seat N477 controls the pneumatic lumbar support as well as seat side and seat back bolster adjustment1). • Valve block 2 in front passenger seat N478 controls the pneumatic cushions for the massage function1).Diagnostic address Data bus communication Special features1)only available in combination with optional "individual contour seat" (PR no.: PS8 )24 BackForwards Ξ ContentsControl unit for 3rd seat rowDesignation Equipment Installation location Tasks Seat adjustment control unit, 3rd seat row J857 Optional equipment (PR no.: PE1) In luggage compartment, R/H side, behind luggage compartment side trim. Controlling the functions of the 3rd seat row • Reading in the following senders/sensors/switches: • Buttons and limit switches for seat back adjustment • Activating the following actuators/control elements: • Seat back locking motors and pawl motors 50 Convenience CAN user The signal lines of the seat belt buckles in the 3rd seat row are not read in by J857, but rather are routed from the seat disconnection point directly to the airbag control unit.Diagnostic address Data bus communication Special feature634_025Seat adjustment control unit, 3rd seat row J85725 BackForwards Ξ ContentsRear lid control unitDesignation Equipment Installation location Tasks Rear lid control unit J605 Always fitted On roof cross member, rear centre Controlling the functions of the electrical rear hatch • Reading in the following senders/sensors/switches: • Button for closing the rear hatch • Activating the following actuators/control elements: • Rear hatch drive motors • Luggage compartment cover motor1) 6D Convenience CAN user Rear lid control module activates the rear parking assistance loudspeakers.Diagnostic address Data bus communication Special feature634_027Rear lid control unit J6051)only available in combination with optional "electrical luggage compartment cover" (PR no.: PKC)26 BackForwards Ξ ContentsTrailer detectorDesignation Equipment Installation location Tasks Trailer detector control unit J345 Optional equipment (PR no.: 1D9) In luggage compartment, L/H side, behind luggage compartment side trim. Interconnects the in-car electrics and the trailer electrics • Reading in the following senders/sensors/switches: • Brake light switch, button for electric swivelling tow bar, bend angle sensor for tow bar • Activating the following actuators/control elements: • Warning lamp for tow bar, swivelling ball hitch head motor 69 • Convenience CAN user • LIN master for bend angle sensor for tow bar G280 J345 sends the information relating to bend angle to the onboard power supply control unit J519 via convenience CAN.Diagnostic address Data bus communication Special feature634_024Trailer detector control unit J34527 BackForwards Ξ ContentsSteering column lock control unitDesignation Equipment Installation location Task Diagnostic address Data bus communication Special features Electronic steering column lock control unit J764 Fitting is country specific On steering column Locking and unlocking the steering column 2B Convenience CAN user • Immobiliser user • Can be replaced separately from the steering column634_035Electronic steering column lock control unit J76428 BackForwards Ξ ContentsSteering column electronicsDesignation Equipment Installation location Task Diagnostic address Data bus communication Special feature Steering column electronics control unit J527 Always fitted On steering column Connects the steering column stalk and the electrical components in the steering wheel to the in-car electronics. 16 FlexRay bus user Transfers the LIN signals from the data bus diagnostic interface J533 (master) to the multifunction steering wheel control unit J453 (slave).634_028Steering column electronics control unit J52729 BackForwards Ξ ContentsInstrument clusterDesignation Equipment Installation location Task Diagnostic address Data bus communication Control unit in dash panel insert J285 • Always fitted • Optional Audi virtual cockpit (PR no.: 9S8) In dash panel Display of information relevant to the driver 17 • Infotainment CAN bus user • MOST bus user • If connected by LVDS to information electronics control unit 1 J794 (image transfer for navigation display in instrument cluster) In the Audi Q7, the instrument cluster is not integrated in the immobiliser.Special feature634_029Control unit in dash panel insert J28530 BackForwards Ξ ContentsACC adaptive cruise controlDesignation Equipment Installation location Tasks ACC control unit J428 Optional equipment On lock carrier, front right, behind front bumper cover • Radar scanning of traffic (distance and speed) • Controlling speed and distance • Distance display and distance warnings (only if ACC is deactivated) 13 FlexRay bus user • ACC Stop&Go with integrated traffic jam assistant • Distance display and distance warning – display of distance in seconds and metres in instrument cluster • Function master for ACC control unit 2 J850 • Additional use of radar signals for Pre sense basic, Pre sense front, evasion assistant and turning assistantDiagnostic address Data bus communication Special features634_030ACC control unit J428ACC control unit 2 J850Designation Equipment Installation location Task Diagnostic address Data bus communication Special featuresACC control unit 2 J850 Optional equipment On lock carrier, front left, behind front bumper cover Radar scanning of traffic (distance and speed) 8B FlexRay bus user • ACC control unit 2 is a slave of the ACC control unit J428 and, based on its function, could also be referred to as a sensor. • Additional use of radar signals for Pre sense basic, Pre sense front, evasion assistant and turning assistant31 BackForwards Ξ ContentsMain beam assistDesignation Equipment Installation location Task Diagnostic address Data bus communication Special features Main beam assist control unit J844 Optional equipment (PR no.: 8G1) In rear view mirror Automatic activation and deactivation of main beam in response to oncoming traffic 20 CAN-Extended bus user • J844 can only switch between dipped beam and main beam. Front camera for driver assistance systems R242 is a requirement for Audi Matrix LED headlights. • J844 is only fitted if the customer orders main beam assist and otherwise no other assistance systems, e.g. active lane assist or traffic sign recognition system etc.634_031Main beam assist control unit J84432 BackForwards Ξ ContentsFront cameraDesignation Equipment Installation location Tasks Front camera for driver assistance systems R242 Optional equipment On windscreen above base of rear view mirror Imaging of traffic, traffic signs and lane markers for: • Audi active lane assist (lane departure warning system) • Main beam assist • Road sign recognition • ACC Stop&Go • Pre sense city • Evasion assist • Matrix beam A5 • FlexRay bus user • R242 is connected to the light control units by a sub-bus system. • Forms a functional unit in combination with image processing control unit • The Audi Matrix LED headlights are also calibrated using the front camera for driver assistance systems R242.Diagnostic address Data bus communication Special features634_032Front camera for driver assistance systems R24233 BackForwards Ξ ContentsAutomatic gearboxDesignation Equipment Installation location Task Diagnostic address Data bus communication Special feature Automatic gearbox control unit J217 Always fitted Automatic gearbox mechatronics Monitoring and controlling the automatic gearbox shift operations 02 FlexRay bus user Immobiliser user634_033Automatic gearbox control unit J21734 BackForwards Ξ ContentsSelector leverDesignation Equipment Installation location Tasks Diagnostic address Data bus communication Special features Selector lever sensors control unit J587 Always fitted On selector lever • Indication of selector lever position • Indication of tiptronic commands 81 Infotainment CAN bus user • Can only be replaced together with the selector lever housing. • Selector lever is not mechanically connected to automatic gearbox.Selector lever sensors control unit J587634_03435 BackForwards Ξ ContentsAirbagDesignation Equipment Installation location Tasks Airbag control unit J234 Always fitted Under centre console, front, on centre tunnel • Deployment of airbags, seat belt pretensioners and battery isolation igniter • Audi pre sense • Deployment of the pedestrian protection system 15 • FlexRay bus user • Is connected to the front left (J854) and front right (J855) seat belt pretensioner control units via a sub-bus system. • LIN master for seat occupancy recognition control unit J706 (for North American market only) Inertial sensors for ESCDiagnostic address Data bus communicationSpecial feature634_036Airbag control unit J23436 BackForwards Ξ ContentsFront A/C control panelDesignation Equipment Front air conditioner/Climatronic operating and display unit E87 Always fitted • 2-zone deluxe automatic air conditioning Optional equipment: • 4-zone deluxe automatic air conditioning (PR no.: KH5) • Front and rear ionisers (PR no.: 2V4) In dash panel, centre Controlling: • Temperature • Blower speed • Air flow distribution • Ioniser 08 • Hybrid CAN user • E87 is the LIN master for: • LIN 1: Control motors for flap activation 1 – 15 • LIN 2: Fresh air blower control unit J126, rear fresh air blower control unit J391, ioniser, driver side J1105, auxiliary air heater control unit  J604, air humidity sender in the fresh air intake duct G657, air quality sensor G238, high pressure sender G65, control motors for flap activation 1 – 5 Although the seat seating and seat ventilation switches are integrated in and read in by operating unit E87, the onboard power supply control unit J519 is responsible for their activation.Installation location TasksDiagnostic address Data bus communicationSpecial featureFront air conditioner/Climatronic operating and display unit E87634_037Rear A/C control panelDesignation Equipment Installation location Tasks Rear air conditioner/Climatronic operating and display unit E265 Optional equipment (PR no.: KH5) In centre console, rear Controlling (in rear area): • Temperature • Blower speed • Air flow distribution • Seat heating • Ioniser 28 • Hybrid CAN user • LIN master for: Control motors for flap control 1 – 7; ioniser, rear passenger side J1108 • Rear air conditioner/Climatronic operating and display unit is, in certain configurations, the LIN slave of front air conditioner/Climatronic operating and display unit E87. • Althoguh the blower speed for the rear occupants is set in E265, the rear fresh air fan control unit J391 is the LIN slave of the front air conditioner/Climatronic operating and display unit E87.Diagnostic address Data bus communication Special featuresRear air conditioner/Climatronic operating and display unit E265634_038 37 BackForwards Ξ ContentsEngine control unitDesignation Equipment Installation location Tasks Engine control unit J623 Always fitted In engine bay, L/H side, in front of plenum chamber • Controlling the engine characteristic • Activation of starter relays J906 and J907 • Function master for start-stop system 01 • FlexRay bus user • J623 is connected to NOx senders and the particulate sensor (diesel engine) via a sub-bus system. • Immobiliser user • Control unit including new connectors with a total of 315 pins – new VAS 6606/23 adaptor line for test box VAS 6606Diagnostic address Data bus communicationSpecial features634_039Engine control unit J62338 BackForwards Ξ ContentsSCR systemDesignation Equipment Installation location Task Diagnostic address Data bus communication Special feature Reducing agent metering system control unit J880 Always fitted in diesel engines In luggage compartment, R/H side, behind luggage compartment side trim. Controlling the injection of reduction agent for reduction of the nitrous oxides in the exhaust gases AC CAN-Extended bus user The size of the reduction agent tank can vary. Standard SCR tank capaciity 12 l; "extended range" SCR tank capacity 24 l1).634_040Reducing agent metering system control unit J8801)Optional equipment 39 BackForwards Ξ ContentsHead-up DisplayDesignation Equipment Installation location Task Diagnostic address Data bus communication Special features Control unit for windscreen projection (head-up display) J898 Optional equipment (PR no.: KS1) In dash panel, directly in front of instrument cluster Controlling all optical, mechanical and electrical components of the head-up display 82 Infotainment CAN bus user • Control units can only be replaced complete with the other components of the head-up display. • To replace the head-up display, the windscreen must be removed. • Note: When replacing the windscreen: Head-up display requires a special screen (with wedge-shaped foil).634_041Control unit for windscreen projection (head-up display) J89840 BackForwards Ξ ContentsNight vision assistDesignation Equipment Installation location Tasks Control unit for night vision system J853 Optional equipment (PR no.: 9R1) In footwell, front left, on floor panel • • • • • 84 • CAN-Extended bus user • J853 is connected by LVDS to the camera for night vision system R212. Supply of camera for night vision system with battery voltage Processing and evaluation of camera images Detection and highlighting of persons and wild animals Calculation and, where applicable, collision warning Transfer of thermal image to the instrument clusterDiagnostic address Data bus communication634_042Control unit for night vision system J85341 BackForwards Ξ ContentsReversing cameraDesignation Equipment Installation location Task Diagnostic address Data bus communication Special feature Reversing camera system control unit J772 Optional equipment (PR no.: KA2) In handle (soft touch) on rear hatch Processing and transfer of images from the area to the rear of the car to the information electronics control unit 1 J794 6C CAN-Extended bus user Control unit, camera and wiring loom form a unit (as shown)634_043Reversing camera system control unit J772 (with built-in camera)42 BackForwards Ξ ContentsSurround view camerasDesignation Equipment Surround view camera control unit J928 Optional equipment, available in combination with: • Parking aid plus (PR no.: 7X2) • Park assist (PR no.: 7X5) In luggage compartment, L/H side, behind luggage compartment side trim. The control unit reads in the data from the 4 surround-view cameras and, from this, calculates images mapping the area around the car. 6C • CAN-Extended bus user • Image transfer to instrument cluster by LVDSInstallation location Task Diagnostic address Data bus communication634_044Surround view camera control unit J92843 BackForwards Ξ ContentsTyre pressure loss indicatorDesignation Equipment Installation location Tasks Tyre pressure monitor system control unit J502 Optional equipment (PR no.: 7K3) On rear axle subframe • Pick-up and evaluation of signals from tyre pressure sensors G222, G223, G224 und G225 • Indication of tyre pressures or issuance of warnings to information electronics control unit 1 J794 65 • CAN-Extended bus user • Communication with the tyre pressure sensors by radio • Control unit with built-in aerial • In addition to indicating tyre pressure and temperature, tyre pressure sensors provide information on the rotational direction of the tyres. • From the strength of the radio signals, the control unit can assign the sensors to the front and rear axles. This together with information on the rotational direction of the tyres enables the signal to be clearly assigned to a specific wheel.Diagnostic address Data bus communication Special features634_045Tyre pressure monitor system control unit J50244 BackForwards Ξ ContentsAuxiliary heaterDesignation Equipment Installation location Tasks Auxiliary heater control unit J364 Optional equipment (PR no.: PK6) In wheel arch, front right, on side member • Reading in the following senders/sensors/switches: • Temperature sensor, flame monitor • Switch-on signals of the radio receiver for the auxiliary heater • Activating the following actuators/control elements: • Fuel metering pump, combustion air blower • Heater glow plug, heating element for fuel preheating • Coolant circulation pump, heater coolant shut-off valve 18 CAN-Extended bus user Contrl unit integrated in heaterDiagnostic address Data bus communication Special feature634_046Auxiliary heater control unit J36445 BackForwards Ξ ContentsLane change assistDesignation Equipment Installation location Tasks Lane change assist control unit J769 (master) Lane change assist control unit 2 J770 (slave) Optional equipment (PR no.: 7Y1) In bumper cover, rear left and right Radar monitoring system for the detection of vehicles (cycles and automobiles) in the area to the rear and side of the car. • Audi pre sense rear including Audi side assist • Rear cross traffic assist • Exit warning • 3C – J769 (master) • CF – J770 (slave) • CAN-Extended bus user • Both control units are also interconnected by a sub-bus system. The control unit is integrated in the bumper cover. The system has to be calibrated after removal and installation.Diagnostic address Data bus communication Special feature634_047Lane change assist control unit J769Lane change assist control unit 2 J77046 BackForwards Ξ ContentsElectronic Stability Control (ESC)Designation Equipment Installation location Tasks ABS control unit J104 Always fitted In engine bay, L/H side • • • • • • • 03 FlexRay bus user • The control unit can be replaced separately from the valve block using ESD protective mat VAS 6613. • The electro-mechanical parking brake is integrated in the ABS control unit. Address word 53 is no longer used for electro-mechanical parking brake. Anti lock braking system (ABS) Electronic Stability Control (ESC) Traction Control System (TCS) Electronic Differential Lock (EDL) Electronic transverse lock Multicollision brake Electro-mechanical parking brake (EPB)Diagnostic address Data bus communication Special features634_048ABS control unit J10447 BackForwards Ξ ContentsPower steeringDesignation Equipment Installation location Tasks Power steering control unit J500 Always fitted Connected to steering gear • Power steering • Servotronic speed-responsive power steering • Corrective steering inputs in conjunction with Audi active lane assist, park assist, evasion assist and trailer assist • Corrective steering intervention with ESP 44 FlexRay bus user The control unit with power steering motor as well as the steering angle sender G85 can only be replaced together with the steering gearDiagnostic address Data bus communication Special feature634_056Power steering control unit J50048 BackForwards Ξ ContentsAll-wheel steeringDesignation Equipment Installation location Tasks Rear axle steering control unit J1019 Optional equipment (PR no.: 0N5) On rear axle subframe Controlling the angle of lock angle of the rear wheels depending on speed and steering angle • Reading in the following senders/sensors/switches: • Steering rack position sender • Activating the following actuators/control elements: • Electric motor for rear axle steering CB FlexRay bus user The control unit and the electric motor for rear axle steering are a unit and can only be replaced separately.Diagnostic address Data bus communication Special feature634_049Rear axle steering control unit J101949 BackForwards Ξ ContentsAdaptive suspensionDesignation Equipment Chassis control unit J775 Optional equipment • adaptive air suspension (PR no.:1BK) • adaptive air suspension (PR no.: 2MA) Under centre console, front, on centre tunnel Level control • Reading in the following senders/sensors/switches: • Button for loading level • Level control system sensor (4 pcs.) • Pressure sender for adaptive suspension • Compressor temperature sensor for adaptive suspension • Activating the following actuators/control elements: • Outlet valve for adaptive suspension • Adaptive suspension compressor motor • Suspension strut valve (4 pcs.) • Pressure accumulator valve for adaptive suspension 74 • FlexRay bus user • A sub-bus system connected to the adaptive suspension compressor motor V66. Transmits the data from the level control system sensors to the onboard power supply control unit J519 via the data bus. The onboard power supply control unit utilises this data to activate the headlight range adjustment system.Installation location TasksDiagnostic address Data bus communication Special feature634_055Chassis control unit J77550 BackForwards Ξ ContentsInterior soundDesignation Equipment Installation location Tasks Structure-borne sound control unit J869 Installed in diesel models In plenum chamber, centre, below windscreen • Reading in the following signals: • Engine speed and engine load (engine control unit J623) • Gear (automatic gearbox control unit J217) • Driving speed (ABS control unit J104) • Driving profile (onboard power supply control unit J519) • Activating the following actuator: • Structure-borne sound actuator R214 A9 CAN-Extended bus user The structure-borne sound actuator R214 is bolted to the body below the windscreen. The actuator produces structure-borne sound (body vibrations) which is transmitted to the windscreen. The windscreen acts as a loudspeaker membrane and converts the structure-borne sound to airborne sound which is audible to the car's occupants.Diagnostic address Data bus communication Special featureBolts for attachment to bodyStructure-borne sound control unit J869Structure-borne sound actuator R214634_05051 BackForwards Ξ ContentsInformation electronicsDesignation Equipment Installation location Task Diagnostic address Data bus communication Information electronics control unit 1 J794 Always fitted In glove compartment Controlling the infotainment systems 5F • Infotainment CAN bus user • MOST bus user • J794 is connected to the MMI display J685 and the multimedia system operating unit E380 via the Modular Infotainment System (MIB) CAN. • Connected to dash panel insert control unit J285 and MMI display J685 by LVDS (image transfer for navigation display in instrument cluster or MMI display). J794 is the system manager and the ring break diagnostics master for the MOST bus.Special featuresInformation electronics control unit 1 J794634_051Sound amplifierDesignation Equipment Digital sound package control unit J525 Optional equipment • Bang&Olufsen Advanced Sound System with 3D sound (PR no.: 8RF) • Bose sound system with 3D sound (PR no.: 9VS) In luggage compartment, rear left, under luggage compartment floor cover Activating up to 23 loudspeakers 47 MOST bus userInstallation location Task Diagnostic address Data bus communicationDigital sound package control unit J525634_05352 BackForwards Ξ ContentsTV tunerDesignation Equipment Installation location Task Diagnostic address Data bus communication TV tuner R78 Optional equipment (PR no.: QV1) In luggage compartment, R/H side, on wheel arch behind luggage compartment side trim TV reception 57 MOST bus userTV tuner R78634_052DVD changerDesignation Equipment Installation location Task Diagnostic address Data bus communication DVD changer R161 Optional equipment (PR no.: 6G2) In luggage compartment, L/H side, behind luggage compartment side trim. Reading in DVDs and transmission of data to information system control unit 1 J794 0E MOST bus userDVD changer R161634_054 53 BackForwards Ξ ContentsExterior lightsHeadlight variantsIn the case of the Audi Q7, a distinction is made between three headlight versions: • Xenon headlight (ECE1) and SAE2)) • LED headlight (ECE1) and SAE2)) • Audi Matrix LED headlight (ECE1))Xenon headlightThe figure shows the left headlight in the ECE1) version.Sealing cover in headlight housing – access for changing bulbs "Service"Headlight range control servomotor V48 "Service" Left LED module for daytime runn