TECHNICAL DOCUMENTATION
SSP 639 Audi 10l 3 cylinder TFSI engine

This PDF is currently unavailable.
Read document text
Self Study Programme 639 For internal use onlyAudi 1.0l 3-cylinder TFSI engine EA211 seriesAudi Service Training BackThe new 1.0l 3-cylinder TFSI engine by Audi represents the next stage in the evolution of the EA211 series. First used in the VW Polo, the engine developed by VW in Wolfsburg is the new entry-level option for the 2015 model Audi A1. It replaces the 1.2l engine of the EA111 series. The engine has more power and achieves better fuel economy than the outgoing unit while meeting the EU 6 emission standard. The new engine is not only about 15 kg lighter than the 1.2l engine from the same series, but also produces less internal friction. The initial engine develops 70 kW (95 BHP). Further performance classes will be offered at a later date. Audi also plans to use this engine on its A3 models.Forward Ξ ContentsFor the first time, Audi is offering a 3-cylinder petrol engine. Although 3-cylinder engines already existed back in the days of Auto Union, they were twin-stroke engines. The last production passenger car to feature these engines was the DKW F 102 produced in 1966. Its engine had a displacement of 1.2 l and developed 44 kW (60 BHP). Up until 1988, engines of this type were installed on the Wartburg 353 in the former GDR. The technical description of the engine in this SSP refers to the Audi A1.1.0l 3-cylinder TFSI engine (70 kW / 95 BHP) Model year 20151.2l twin-stroke 3-cylinder petrol engine (44 kW / 60 BHP) Model year 1966DKW F 102639_002Learning objectives of this self study programme: This self study programme describes the design and function of the 1.0l 3-cylinder TFSI engine. Once you have completed this self study programme you will be able to answer the following questions: • How do the engine mechanicals work? • How are the lubrication, cooling, turbocharging, fuel, fuel injection, exhaust and ignition systems configured?2ContentsIntroductionBrief technical description __________________________________________________________________________________________________________________________________ 4 Specifications _ ________________________________________________________________________________________________________________________________________________ 5Engine mechanicalsModular design _______________________________________________________________________________________________________________________________________________ 6 Crankcase ventilation, activated charcoal system ________________________________________________________________________________________________________ 6 Engine block and oil pan _ ___________________________________________________________________________________________________________________________________ 7 Crankshaft drive ______________________________________________________________________________________________________________________________________________ 8 Belt-drive system _ ___________________________________________________________________________________________________________________________________________ 10 Cylinder head ________________________________________________________________________________________________________________________________________________ 12 Valvegear module ___________________________________________________________________________________________________________________________________________ 13Oil supplyIntroduction _________________________________________________________________________________________________________________________________________________ 14 Oil circuit _____________________________________________________________________________________________________________________________________________________ 14 Oil pump _____________________________________________________________________________________________________________________________________________________ 14 Oil pressure control _________________________________________________________________________________________________________________________________________ 16Cooling systemIntroduction _________________________________________________________________________________________________________________________________________________ 20 Coolant circulation __________________________________________________________________________________________________________________________________________ 20 System overview ____________________________________________________________________________________________________________________________________________ 21 Thermostat __________________________________________________________________________________________________________________________________________________ 22 Coolant pump _______________________________________________________________________________________________________________________________________________ 22Air supply and turbochargingOverview _____________________________________________________________________________________________________________________________________________________ 23 Exhaust turbocharger _ ______________________________________________________________________________________________________________________________________ 24 Charge pressure actuator V465 _ ___________________________________________________________________________________________________________________________ 25Fuel systemSystem overview ____________________________________________________________________________________________________________________________________________ 26 Ignition ______________________________________________________________________________________________________________________________________________________ 27Engine management systemSystem overview (2015 model Audi A1) __________________________________________________________________________________________________________________ 28 Lambda control _____________________________________________________________________________________________________________________________________________ 30ServiceSpecial tools and workshop equipment _ __________________________________________________________________________________________________________________ 32 Maintenance operations ____________________________________________________________________________________________________________________________________ 33AppendixGlossary ______________________________________________________________________________________________________________________________________________________ 34 Self study programmes _ ____________________________________________________________________________________________________________________________________ 35The self study programme teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a repair manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. This content is not updated. For further information about maintenance and repair work, always refer to the current technical literature. In the glossary at the end of this self study programme you will find an explanation of all terms written in italics and indicated by an arrow ↗.NoteReference3 BackForward Ξ ContentsIntroductionBrief technical description• 3-cylinder in-line engine with petrol direct injection • Turbocharger with indirect intercooler • 4 valves per cylinder, double overhead camshafts (DOHC), roller-type cam followers • 1 intake camshaft and 1 exhaust camshaft • Bosch engine management system • Ceramic catalytic converter with catalyst heating by twin injection (homogeneous split) • Fully electronic direct injection with drive by wire • Timing belt drive gear • Start-stop / recuperation energy management639_003Reference The design and function of the basic engine are explained in Self Study Programme 616 "Audi 1.2l and 1.4l TFSI engines of the EA211 series".4 BackForward Ξ ContentsSpecificationsTorque-power curve Power output in kW Torque in NmEngine speed [rpm]639_009Features Engine code Type Displacement in cm3 Stroke in mm Bore in mm Number of valves per cylinder Firing order Compression ratio Power output in kW at rpm Torque in Nm at rpm Fuel type Turbocharging Exhaust gas treatment Emission standard CO2 emissions in g/km1)Specifications CHZB 3-cylinder inline engine 999 76.4 74.5 4 1–2–3 10.5 : 1 70 at 5000 - 5500 160 at 1500 - 3500 Premium unleaded 95 RON Exhaust turbocharger 3-way catalytic converter EU 6 • with 15“ and 16“ wheels: 97 g (efficiency class A) • with 17“ wheels: 98 g (efficiency class A) • with 18“ wheels: 102 g (efficiency class B)1)The specified CO2 emission values apply to the 2015-model Audi A1 with 5-speed manual gearbox.5 BackForward Ξ ContentsEngine mechanicalsModular designAs with all engines of the EA211 series, the 3-cylinder employs the proven modular design. The following diagram highlights the individual module groups.Exhaust moduleCylinder head cover with integrated valvegear moduleCoolant pump moduleCylinder headIntake module639_014Timing and auxiliary drive moduleEngine blockOil pan moduleCrankshaft driveCrankcase ventilation, activated charcoal systemThis system adopts the functional principle employed by the 4-cylinder EA211 engines. For a description please refer to SSP 616.6 BackForward Ξ ContentsEngine block and oil panThe engine block is manufactured from aluminium using the gravity die casting method. It has an open deck ↗ design. The cylinder liners are made from cast iron. They are cast into the engine block during the casting process. Their outer surface is rough. This increases their surface area thereby optimising heat transfer. It also ensures that the liners are more securely seated in the engine block. The surfaces of the cylinder liners are fluid jet honed in a 4-step process. The plate honing method is used to avoid cylinder warpage.Aluminium cylinder block with open-deck designMain crankshaft bearingsSurge baffle (oil windage tray)Oil level and temperature sensor G266Die-cast aluminium oil pan639_004Reference For further information about the open-deck design, please refer to Self Study Programme 616 "Audi 1.2l and 1.4l TFSI engines of the EA211 series" and Self Study Programme 626 "Basics of Audi Engine Technology".↗ Refer to "Glossary" on page 34.7 BackForward Ξ ContentsCrankshaft driveIn developing the crankshaft drive, special attention was given to minimising moving masses and friction. Thanks to the measures listed below, it was possible to dispense with a balancer shaft while retaining a very high level of running comfort. • The weight of the forged conrods and the aluminium pistons was kept low by using a flat piston crown design. • Hollow drilled bearing crank pins • The design of the crank webs. • Selective use of imbalance weights on the torsional vibration damper and on the opposing flywheel.100% of the rotating masses and 50% of the oscillating masses are balanced.The small-sized main and big end bearings also help reduce friction.TDC mark on vibration damperFlywheel639_011Vibration damperDrive gear for engine timing beltHollow drilled crank pinCrankshaft8 BackFeatures Cylinder spacing Bore Stroke Main bearing diameter Big end bearing diameter Conrod length Gudgeon pin diameter Specifications 82.0 mm 74.5 mm 76.4 mm 45.0 mm 47.8 mm 140.0 mm 19.0 mmForward Ξ ContentsSpecial featureTwo-component bearing Two-component bearingAluminium pistons with valve recessesPistons and conrodsA new feature of the gudgeon pins is that they now run on bushless bearings. No bush is used in the conrod small end. This necessitated applying a DLC ↗ coating to the floating gudgeon pins. It was also necessary to roller burnish ↗ the surfaces of the conrod small ends.Trapezoidal conrod639_008↗ Refer to "Glossary" on page 34.9 BackForward Ξ ContentsBelt-drive systemThe belt-drive system is maintenance-free. This is due to the use of trioval camshaft timing belt sprockets, which almost completely eliminate any forces that arise and ensure that the timing belt runs smoothly. This allows the tensioning force of the automatic tensioning pulley to be reduced, resulting in less friction. This makes the system more stable while also improving fuel economy.Assembly tool T10476AWhen carrying out assembly work, care must be taken to ensure that the trioval camshaft timing belt sprockets are correctly positioned. Assembly tool T10476A must be used for this purpose (refer to page 32).Exhaust camshaft adjuster with trioval timing belt sprocketInstalling the crankshaft timing belt sprocketThe crankshaft timing belt sprocket fits onto the crankshaft in one position only.10 BackThe top dead centre point of the crankshaft on the 1.0 TFSI engine can be checked against the marks on the vibration damper and on the timing belt housing cover. In the case of EA211 series engines, the TDC position previously had to be checked using tool T10340.Forward Ξ ContentsFor this purpose, it was necessary to remove the propshaft from the 3-cylinder engine. The exact procedure for setting and checking the camshaft timing is explained in the current Workshop Manual.Camshaft adjusterFeatures Adjustment range in ° crank angle Locked position of camshaft after shutting off engine Intake camshaft 50 retard (turned automatically in direction of rotation of engine) Exhaust camshaft 40 advance (turned counter to direction of rotation of engine by resetting spring)Intake camshaft adjuster with trioval timing belt sprocketInstalling the vibration damperMark on vibration damper and TDC mark at bottom of timing belt guard. The crankshaft timing belt sprocket and the vibration damper fit in any position. The TDC mark on the vibration damper and on the crankshaft timing belt sprocket must be in alignment.Automatic tensioning pulley with flange for guiding the timing beltGuide pulleyVibration damper with Hirth splineCrankshaft timing gear sprocket with Hirth spline639_00511 BackForward Ξ ContentsCylinder headThe cylinder head is manufactured from an aluminium alloy using a special tilt gravity die casting process followed by heat treatment. This produces joins of a very high quality. As is the case with the 4-cylinder TFSI engines from the EA211 series, the exhaust manifold of the 3-cylinder engines is integrated in the cylinder head. Here the manifold is encased in its own coolant jacket. The intake ducts have been improved over the 4-cylinder TFSI engines. This enhances the tumble flow of the exhaust gases and gives a higher flow rate, which in turn translates to better mixture formation. Advantages over conventional manifolds: • Short flow pathways of the exhaust gas to the exhaust turbocharger turbine. • Faster transfer of heat into the coolant after cold start. • Low wall heat loss. • Faster heating of the engine, resulting in reduced engine friction during the warm-up phase. • Faster heating of the cabin.Roller-type cam follower with hydraulic support element and retaining clipValve spring retainer Valve stem seal Valve cotters Valve spring Intake valves Cylinder head639_006639_015Oil pressure switch F1 Intake endCylinder head gasketExhaust port with flange connecting to turbochargerExhaust endThe fixed valve seat angle protects against valve wear when using alternative fuels, e.g. fuels with a high ethanol content.The cylinder head must be replaced if the valve guides are worn. Valves and valve seats may be ground but not machined.12 BackFeatures Valves per cylinder Valve material Seat rings Intake valve installation angle Exhaust valve installation angle Intake-end valve seat angle Exhaust-end valve seat angle Valve stem diameter Valve control Valve clearance Valve dimensions Specifications 4 Solid valves made of high alloyed X45 steel Sintered material 21° 22.4° 90° 120° 5 mm Roller-type cam follower Hydraulic support elements Refer to Workshop ManualForward Ξ ContentsValvegear moduleAs is the case with all engines of the EA211 series, the camshafts run on bearings in the die-cast aluminium cylinder head cover in the valvegear module. All component parts of the camshafts are securely mounted in a special production process. Finally, the two grooved ball bearings are inserted on the timing end. The other camshaft bearings are configured as low-friction bearings.Hall-effect sensor G40 (intake end)Non-return valve (positive crankcase ventilation)Camshaft timing adjustment valve 1 N205639_016Hall-effect sensor 3 G300 (exhaust end)Camshaft housingLow-friction bearingGrooved ball bearingExhaust camshaft timing adjustment valve 1 N31813 BackForward Ξ ContentsOil supplyIntroductionBy reducing friction levels within the engine, it was possible to use an oil pump with a reduced delivery rate. The lower power consumption of the pump offers further potential for making savings. The engine oil is subjected to less stress due to the lower quantity of oil circulated. The use of an infinitely variable map-controlled oil pump is new.Oil circuitThe oil pump draws the engine oil from the oil sump in the oil pan through a plastic suction line. The pressurised oil from the oil pump firstly flows through the engine block to the oil filter attached to the oil pan. From here it flows through the oil cooler into the main oil gallery, where it is distributed to the main and big-end bearings as well as to the cylinder head through a riser line on the timing drive side. Here two galleries supply the roller-type cam followers with oil. The camshaft phasers are supplied with oil through ports at the start of two galleries in the cylinder head. The exhaust turbocharger is supplied with oil through a tube. It is connected to the engine block on the gearbox side. The pressurised oil comes through a port from the last main bearing. The piston cooling jets are also connected to the main oil gallery. They are designed to open when the oil pressure exceeds approximately 2 bar. If the oil pressure drops below 1.7 bar, the jets are closed again through the application of spring force. There is no nonreturn valve for the oil circuit anywhere in the engine. The spin-on oil filter ↗ nas a non-return diaphragm. This ensures that all the downstream areas between the oil filter and the main oil gallery (riser line, oil cooler) are filled with oil after the engine stops. The oil draining out of the consumers returns to the oil pan through the central return duct on the hot side of the engine in the engine block. The exhaust turbocharger return line is externally flange-mounted to this engine block return duct.Oil pumpThe vane pump is flange mounted to the engine block behind the vibration damper. It is driven directly by the crankshaft by means of an interlocking connection (polygon).Features Engine speed Control pressure FailsafeSpecifications 1 : 1 engine speed 1.3 – 3.3 bar (relative) 4.5 bar (by mechanical and hydraulic function in oil pressure control valve N428) 7 barCold start valve639_017Oil pressure control valve N428Vane pumpNote The engine is operated at a higher oil pressure during the first 1000 km. This is a run-in protection measure. If a new engine is installed, this function must be reactivated using the diagnostic tester. For this purpose, the adaption function includes the option "Oil pressure for engine run-in".↗ Refer to "Glossary" on page 34.14 BackForward Ξ ContentsOverview of the oil circuitExhaust camshaft timing adjustment valve 1 N318 Camshaft timing adjustment valve 1 N205 Oilways for supplying the camshafts and the hydraulic support elementsExhaust turbocharger oil supplyOil pressure sensor G10Engine oil coolerPiston cooling nozzleMain oil galleryOil pressure control valve N428 Riser line to main oil gallery (clean oil) Oilway (unfiltered oil)Oil filter with nonreturn diaphragmFlow-regulated oil pump configured as vane pumpOil pan639_007 15 BackForward Ξ ContentsOil pressure controlA map-controlled oil pump is used by VW and thus also by Audi for the first time. It produces the required oil pressure steplessly and according to demand. Oil pressure is controlled by a hydraulic control circuit and by an electrical control circuit.Vane cellControl chamberdesirePr esSuVane Control surface Oil pressure control valve N428 Full delivery stop Control spring Intake tubeFrom the oil circuit to oil pressure control valve N428Pivot pointAdjustment ringPump outletCold start valveInner ringct io nsuside639_038Comparison of various control strategies3,5 3,3Oil pressure [bar]1,81,3Engine load [Nm], engine speed [rpm], oil temperature [°C]639_028Key: Oil pressure is controlled steplessly (1.0l TFSI engines) Oil pressure is controlled in 2 stages (1.4l TFSI engines) Oil pressure is not controlled (1.2l TFSI engines)16The cold start valve protects the engine when the oil pressure is too high. It opens when the pressure exceeds 7 bar (relative). BackForward Ξ ContentsControl functionPressurised oil is diverted from the main oil gallery in the engine block. This oil flows through the oil pressure control valve N428 and into the chamber above the spring-loaded swivelling oil pump guide ring. The pump is operated by the engine control unit by means of a PWM signal ↗. Depending on how it is activated, N428 opens the duct to a greater or lesser degree via the oil pump guide ring. The guide ring counters the force of the pressure spring and alters the geometry of the pump interior in such a way that the pump conveys less oil. The demand for engine oil increases with rising engine speed. Engine oil is made available by increasing the oil pressure. Lubricating oil demand is computed on the basis of a characteristic map. The data from the following sensors is used to compute and monitor the oil pressure: • Oil level and oil temperature sender G266 (for computing the viscosity) • Oil pressure sensor G10Reducing the oil flow rate and the oil pressure • The oil pressure control valve N428 is activated by the engine control unit by means of a PWM signal and extended pulse width, increasing the cross section of the supply line to the control chamber. • The oil pressure acts on the control surface of the oil pump. • The resultant force is greater than that exerted by the control spring and swivels the adjustment ring clockwise towards the centre of the vane pump. The volume of the delivery chamber is reduced on the suction and pressure sides and less oil is fed into the oil circuit depending on the extent to which the control spring is compressed. The quantity of oil and thus the oil pressure decreases.Adjustment ringControl surface Control chamberControl springLow oil delivery rate and oil pressure The oil acts on the control surface of the adjustment ring.639_020To control chamberFrom oil circuit (main oil gallery)ULarge pulse width Compression spring Oilway to control chamber is open639_025t639_024↗ Refer to "Glossary" on page 34.17 BackIncreasing the oil flow rate and the oil pressure • The oil pressure control valve N428 is activated by the engine control unit by using a PWM signal and smaller pulse width, reducing the cross section of the supply line to the control chamber. • A reduced oil pressure acts on the control surface of the oil pump. • The resultant force is less than that exerted by the control spring and swivels the adjustment ring counter-clockwise towards the full delivery stop. The volume of the delivery chamber on the suction and pressure sides is increased and the oil pump feeds a larger quantity of oil into the oil circuit. The quantity of oil and thus the oil pressure increases.Forward Ξ ContentsAdjustment ringHigh oil delivery rate and oil pressure The oil pressure inside the control chamber is reduced.To control chamber From oil circuit (main oil gallery)Full delivery stop639_021ULow pulse width639_027t639_026Regulating piston Oilway to control chamber is partially openOil pressure sensor G10To implement the infinitely variable oil pressure control function, it is not sufficient to monitor the oil pressure using an oil pressure switch. This is why an oil pressure sensor is used here. Oil pressure sensor G10 measures the full oil pressure range. It is attached to the cylinder head by screws in the area of the intake manifold and the alternator. The pressure signal from the sensor is evaluated in the electronics sensor and output to the engine control unit by SENT ↗ protocol. The oil pressure can be displayed in the relevant measured value ([IDE02742]_Oil Pressure Actual Value).ActivationJ623Key: G10 Oil pressure sensor J623 Engine management control unit 1 Sensor 2 Sensor signal (SENT) 3 Sensor + (5 V) 4 PIN 2 5 PIN 1 6 PIN 3639_019Oil pressure sensor G10123639_01845 G106Note Due to its captive seal, the oil pressure sensor G10 may only be screwed into place once. To check the oil pressure, follow the instructions given in the Workshop Manual and in the Guided Fault Finding.↗ Refer to "Glossary" on page 34.18 BackForward Ξ ContentsOil pressure control valve N428An oilway opens when the electrical proportional valve (hydraulic 3/2 way valve) integrated in the oil pump casing is activated by the engine control unit. This allows the pressurised oil coming from the main oil gallery to flow into the pump chamber (control chamber) in which the control surface of the adjustment ring is located. Oil pressure is built up here. The adjustment ring counteracts the force of the control spring and thus reduces the volume of the pump delivery chamber. The delivery rate of the pump and thus also the oil pressure decreases. The engine control unit utilises a PWM signal (200 Hz) to activate N428. The cross section of the oilway to the pump chamber varies according to the duty factor (between 20 and 80 %). ActivationJ623Key: J623 Engine management control unit N428 Oil pressure control valve 1 Ground (PWM signal) 2 Terminal 87a1 Oil pressure control valve N428 N428639_0222Failsafe functionIf the oil pressure control valve N428 fails electrically or if a fault occurs in the cable connection, the oil pump runs at its full delivery rate. This ensures that the engine always has sufficient oil pressure.639_023In Failsafe mode, the oil pressure is adjusted mechanically to 4.5 bar (relative) by N428. This is necessary because otherwise the pressure could rise too much when the engine is cold due to the higher viscosity of the engine oil.Oil pressure control in Failsafe mode If N428 is no longer activated electrically in the event of a fault, the pump switches to its "maximum delivery rate" for functional reasons. In the de-energised state, the regulating piston is displaced mechanically by the compression spring in such a way it shuts off the supply duct to the pump control chamber. The regulating piston has two different piston surfaces, resulting in an annular surface. The presence of oil pressure produces a force which acts against the compression spring. At a relative oil pressure of approx. 4.5 bar (this applies to an oil temperature of 120 °C), the piston opens the bypass and oil flows through the servo valve and into the oil pump control chamber. The adjustment ring in the oil pump is adjusted towards the minimum delivery rate. The oil pump now delivers less oil thereby limiting any further increase in oil pressure within the engine. If the oil pressure drops below the minimum threshold, the "red oil can" symbol appears in the instrument cluster. The driver is advised to shut off the engine.DiagnosticsThe oil pressure control valve and the oil pressure sensor are monitored by the engine control unit. Any plausibility errors and electrical faults which occur are registered in the event memory. In engine control unit software versions 2166 and 2256 and higher, the EPC lamp in the instrument cluster is also activated. The relevant test routines are available in the Guided Fault Finding mode. Long name Oil_Pressure_Actual_Value Oil_pressure_commanded_value Oil_pressure_control_Actual_Value_I_Component Oil_pressure_control_value_duty_factor Oil_pressure_sensor_raw_value Text_ID IDE02742 IDE11203 IDE11929 IDE11330 IDE11329 The activation of the oil pressure control valve can be monitored under "Read measured values". Another key measured value is that of the oil pressure sensor (Oil P p Val Sent Snsr). Its plausibility can for example be checked against the ambient air pressure value when the engine is at a standstill (engine control unit software version 2054).Diagnostic tester display Actual oil pressure Specified oil pressure PID control I-component of fully variable oil pump Oil pressure control valve, activation duty factor Oil pressure sensor, raw valueUnit bar bar %19 BackForward Ξ ContentsCooling systemIntroductionThe engine cooling function and the thermal management function are to a large extent derived from the previous engines of the EA211 series. The entire circuit is subdivided into low and high temperature circuits.Low-temperature circuitThe low-temperature cooling circuit is operated on demand by means of charge air cooling pump V188. The charge air cooler and the exhaust turbocharger are integrated within this circuit. After the hot engine is shut off, the pump run-on function is activated in order to protect the components.High-temperature circuitEngine cooling is provided by the coolant pump installed in the coolant pump module. The coolant pump is driven by a maintenance-free timing belt via the exhaust camshaft.Cylinder head From radiator Engine block Coolant pump Thermostats 1 and 2Coolant circulationSmall cooling circuitThe mechanically driven pump conveys the coolant through a connecting duct in the cylinder head to the water gallery in the engine block. From here the main flow is directed through the head gasket and into the cylinder head. Here it meets the transverse flow for cooling the combustion chambers as well as the second, parallel cooling flow for cooling the integral exhaust manifold.639_042Both partial flows merge upsteam of the thermostat housing and flow together into the mixing chamber upstream of cylinder head thermostat 1. This thermostat opens when the engine temperature exceeds 80 °C, allowing coolant to flow through the heater matrix. This temperature is the best compromise between friction reduction, efficiency-optimised ignition and minimal knock tendency.Large cooling circuitThe coolant flows directly through the engine oil cooler at the start of the engine block gallery. Upstream of cylinder 1 the coolant flows back into the engine block gallery. The engine block cooling circuit begins here. The coolant bypasses the cylinders and flows through a connecting duct upstream of engine block thermostat 2. The coolant in the engine block is static during the engine warm-up phase. When the engine temperature exceeds 105 °C, engine block thermostat 2 opens and allows the coolant to flow into the mixing chamber upstream of cylinder head thermostat 1. At the same time, it regulates the amount of coolant which flows through the radiator.20To radiator BackForward Ξ ContentsSystem overview1 235G624680 °C78910105 °C117 V51 7 V7 12 13 14 G83Key: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Coolant expansion tank Heater matrix Exhaust turbocharger Cylinder head/engine block Integrated exhaust manifold cooling Coolant pump module with integrated coolant thermostat Non-return valve Cylinder head cooling Engine block cooling Engine oil cooler Charge air cooler in intake manifold Flow restrictor Radiator for charge air cooling Radiator G62 G83 V7 V51 Coolant temperature sensor Coolant temperature sensor at radiator outlet Radiator fan Coolant run-on pump639_010High-temperature circuit Cooled coolant Warm coolantLow-temperature circuit Charge air cooling, cold coolant Charge air cooling, warm coolant21 BackForward To heater matrixΞ ContentsThermostatThe coolant thermostat is integrated in the coolant pump module. There are 2 thermostats inside the coolant thermostat housing. These are expanding wax thermostats with different temperature ratings. Both can be replaced separately.Thermostat 2 for cylinder blockThermostat 1 This is the main thermostat and it regulates the amount of coolant which flows through the main radiator. It begins to open at a coolant temperature of 80 °C.Thermostat 2 Opens upwards of 105 °C and allows heated coolant to flow from the cylinder block to the radiator. The entire coolant circulation system is open.From heater matrixThermostat 1 Return from radiator Flow to radiator639_040Coolant pumpThe coolant pump is integrated in the coolant pump module. The complete module is bolted onto the cylinder head. It is sealed off from the coolant ducts by rubber gaskets. One gasket sits between the coolant pump housing and the cylinder head, and the other between the coolant pump and the thermostat housing.Coolant temperature 105 °C, both thermostats openThe coolant pump is driven by a separate belt-drive system running off the exhaust camshaft. That belt-drive system is on the flywheel end of the engine and is maintenance free. However, it does have to be replaced if the coolant pump is detached.Thermostat-to-cylinder-head gasketCoolant pump driven by exhaust camshaftCoolant-pump-to-thermostat gasketSupply to heater matrixThermostat 1Thermostat cover gasket Return from heater matrixThermostat housing639_039Coolant pump housingThermostat 2 for cylinder blockSupply to radiatorReturn from radiator22 BackForward Ξ ContentsAir supply and turbochargingOverviewAs with all engines of the EA211 series, the air supply is characterised in particular by short pathways in the charge air circuit. Due to the low charge air volume between the exhaust turbocharger and the combustion chambers, charge air pressure builds up very quickly. As a result, these engines are highly responsive.Charge pressure sensor G31 with intake air temperature sensor 2 G299Heated air in turbocharger outlet pipeAir filter box mounted directly on engine639_030Throttle valve module J338Intake manifold module with integrated charge air cooler23 BackForward Ξ ContentsExhaust turbochargerThe exhaust turbocharger is attached directly at the outlet of the exhaust manifold integrated in the cylinder head. The exhaust gas loses hardly any heat due to the short pathway to the single-scroll turbine. The materials from which the exhaust turbocharger is made have been carefully adapted to suit these conditions. The relatively small charger has a low mass moment of inertia due to its compact size and therefore achieves excellent efficiency. Charge pressure is controlled by an electrical wastegate actuator. The 1.0 3-cylinder TFSI engine has the highest charge pressure to date in the EA211 engine series.Control motor + Control motor Sensor + (5 V) PIN 2 V465 PIN 3 Sensor PIN 1639_033ActivationJ623Technical features• Housing made of heat-resistant austenitic cast steel ↗ (allows exhaust temperatures up to 1050 °C) • Nickel based alloy for the turbine wheel • Electrically driven charge pressure actuator, can be replaced separately (follow instuctions in Workshop Manual and Guided Fault Finding) • Maximum relative charge pressure of 1.6 bar • No wastegate valvePIN 6Sensor signal PIN 5Turbine housingIntegrated pulsation silencerWastegate actuator V465Compressor wheelWastegate valveFlange connecting to cylinder headNot assignedCoupling rod (actuating lever)639_031639_032↗ Refer to "Glossary" on page 34.24 BackForward Ξ ContentsCharge pressure actuator V465FunctionThe actuator is activated by the engine control unit by means of a PWM signal. For this purpose, a basic frequency of 1000 Hz is applied. The pump is activated on the basis of a characteristic map. To ensure that the actuator reaches the correct position, the actual position must be recorded. This task is performed by the charge pressure actuator position sensor G581 (Hall-effect sensor), which is mounted to the output gear of the rotatory drive. It outputs an analog voltage signal to the engine control unit, which is used to compute the position of the wastegate flap. After initialising (adapting) the actuator, the stops of the wastegate flap are "programmed". Consequently, the actuator is capable of operating at very high speeds with the least possible wear. For this purpose, the actuator is braked electrically by means of a PWM signal shortly before reaching the mechanical stops and moves to the calculated electrical stop.Diagnostic options using the diagnostic tester.The charge pressure actuator can be adjusted and/or adapted by means of the Guided Fault Finding or Guided Fault Functions.It is not possible to adjust the charge pressure actuator at the coupling rod. If the charge pressure actuator is replaced in the course of servicing, the coupling rod stays on the exhaust turbocharger and is not replaced. This is the reason why it is not necessary, i.e. would be wrong, to adjust the coupling rod. If servicing is carried out, the new charge pressure actuator only needs to be adapted.The adaption procedure must be performed if: • the charge pressure actuator has been replaced. • a different charge pressure actuator is used due to the installation of a different engine. • the engine control unit has been replaced. • the programmed values have been deleted from the engine control unit. The engine control unit "learns" various positions of the charge pressure actuator when the ignition is on and the engine is at a standstill. These positions are stored in the engine control unit.Key measured valuesMeasured values Specified position Adaption for lower stop Adaption for upper stop Setpoint Actual value Offset closed Offset open Activation Status Raw voltage Code [IDE03932]_charge pressure actuator [IDE03934]_charge pressure actuator [IDE03935]_charge pressure actuator [IDE04278]_bypass valve for turbocharger high pressure turbine inlet [IDE04279]_bypass valve for turbocharger high pressure turbine outlet [IDE04280]_bypass valve turbocharger high pressure turbine inlet [IDE04281]_bypass valve turbocharger high pressure turbine inlet [IDE04301]_bypass valve turbocharger high pressure turbine inlet [IDE04302]_bypass valve turbocharger high pressure turbine inlet [IDE04303]_bypass valve turbocharger high pressure turbine inlet25 BackForward Ξ ContentsFuel systemThe 3-cylinder TFSI engine is the first engine in the EA211 series to have a maximum fuel injection pressure of 250 bar. This measure significantly improves exhaust emissions.System overviewFuel pressure regulating valve N276 High pressure fuel reservoir (rail) Fuel pressure sensor G247Fuel pumpInjectors N30, N31, N32Pressure limiting valvePWM signal + PWM signal PWM signal -Engine control unit J623Battery (positive)GroundDoor contact signalTerminal 15639_034Fuel filterFuel pump control unit J538Fuel predelivery pump G6Fuel feed pressure and return pressure from the injectors approx. 4 – 7 bar Fuel high pressure 100 - 250 bar Fuel return line26 BackForward Ξ ContentsFuel supplyA non-return fuel supply is facilitated by an electrical fuel pump in the fuel tank. Here the fuel pressure calculated by the engine control unit is set by fuel pump control unit J538 on the basis of a model. This means that there is no fuel pressure sensor in the low pressure circuit. The system only delivers as much fuel as is necessary. Vapour bubbles must not form in the fuel system.High pressure systemAll components of the high pressure system need to be adapted to withstand the higher pressures. The Hitachi high pressure pump is driven by the intake camshaft via a 3 lobe cam. High pressure fuel injection is provided by 5 hole electromagnetic injectors. The spray has been optimised to provide homogeneous mixture formation. The high pressure configuration of the fuel injection system allows even the smallest amounts of fuel to be injected. Uo to 3 injection shots are possible during partial and full load operation. Fuel is also injected into the cylinders several times during the catalytic converter heating phase. The required injection rates are computed by the engine control unit. The system is activated by applying 65 V. The fuel rail is made from stainless steel. It has a wall thickness rated for the existing pressure conditions. The cylinder head support has also been reinforced due to the higher pressures to which it is subjected. The opening pressure of the pressure limiting valve in the high pressure pump is approximately 290 bar.639_041IgnitionThe ignition coils are arranged above the spark plugs. They are bolted to the cylinder head cover. The spark plugs are designed such that the ground electrode must be positioned exactly within the combustion chamber. This is the only way to ensure optimal ignition spark deflection in proximity to the ignitable air/fuel mixture and the formation of a stable flame core. It is, therefore, very important to follow the manufacturer's instructions during installation.Reference The control concept of the high pressure pump is explained in Self Study Programme 384 "Audi 1.8l 4V TFSI Engine with Timing Chain".27 BackForward Ξ ContentsEngine management systemSystem overview (2015 model Audi A1)SensorsGearbox neutral position sensor G701Oil pressure sensor G10Knock sensor 1 G61Accelerator pedal position sensor G79 Accelerator pedal position sensor 2 G185Clutch position sensor G476Brake light switch FEngine speed sensor G28Charge pressure sensor G31 Intake air temperature sensor 2 G299Intake air temperature sensor G42 Intake manifold pressure sensor G71 Engine control unit J623Fuel pressure sensor G247Hall-effect sensors 1+2 G40, G163Throttle valve module J338 Throttle actuator position sensors 1+2 for vehicles with electronic accelerator G187, G188Coolant temperature sensor G62Radiator outlet coolant temperature sensor G83Oxygen sensor G39 Oxygen sensor downstream of catalytic converter G130Charge pressure actuator position sender (in charge pressure actuator V465) Auxiliary signals1): • Cruise control system • Vehicle speed signal • Terminal 50 • Crash signal from airbag control unit • Start-stop "off"281)dependent on trim levelPowertrain CANOil level/temperature sensor G266 BackForward Ξ ContentsActuatorsMain relay J271Oil pressure control valve N428Fuel pressure control valve N276Continued coolant circulation pump V51Oxygen sensor heater Z19 Heater for oxygen sensor 1 downstream of catalytic converter Z29Ignition coils 1 – 3 with output stage N70, N127, N291Radiator fan V7 Radiator fan control unit J293Injectors for cylinders 1 – 3 N30 – N32Camshaft control valve 1 N205 Exhaust camshaft timing adjustment valve 1 N318Activated charcoal canister solenoid valve 1 N80Throttle valve positioner G186 for electronic power controlCharge pressure actuator V465Fuel pump control unit J538 Fuel predelivery pump G6 Fuel gauge sensor G639_012Auxiliary signals1): • Automatic gearbox control unit/engine speed • ABS control unit/clutch position • A/C compressor29 BackForward Ξ ContentsLambda controlTwo nonlinear oxygen sensors are used to facilitate lambda control. One sensor is located upstream of the catalytic converter and the other downstream of the catalytic converter. The engine control unit utilises the signals from the oxygen sensor upstream of the catalytic converter G39 to compute the air/fuel ratio. The signals from the oxygen sensor downstream of the catalytic converter G130 are used to check for proper functioning of the catalytic converter as well as to monitor and, where necessary, adapt the oxygen sensor upstream of the catalytic converter.Oxygen sensor G39639_043Oxygen sensor after catalytic converter G130Evaluation of the signal from the oxygen sensor upstream of the catalytic converter G39As with all engines of the EA211 series with 2 nonlinear oxygen sensors, a continuous lambda control function is also integrated into the engine control unit of the 3-cylinder engine. As before, this function not only evaluates the step (2 point lambda control) but also the signal within the step. The air/fuel ratio is adapted very quickly and with a high level of precision. The signal from the sensor is, therefore, constantly within the range of the step. As a result, the control response is approximate to that of a broadband oxygen sensor.2-point lambda controlContinuous lambda controlVoltage Nonlinear oxygen sensor [V]0.9 rich1.0 λ1.1 lean639_044Voltage Nonlinear oxygen sensor [V]0.9 rich1.0 λ1.1 lean639_045Key: This range is evaluated by the lambda control function in the engine control unit.30 BackForward Ξ ContentsComparison of the signal characteristics of the nonlinear oxygen sensor G39 upstream of the catalytic converterThe nonlinear oxygen sensors used the EA111 and EA211 engine series are identical in type and function. They only differ in terms of how the signals are evaluated in the engine control unit. As a result, the digital storage oscilloscope obtains different signal characteristics: • The lambda value at a signal voltage of 450 mV is 1.0. • The lambda value is less than 1.0 at a higher signal voltage. • The lambda value is above 1.0 at a lower signal voltage.Engine series EA111: signal characteristic of nonlinear oxygen sensor G39 upstream of the catalytic converter With the 2 point lambda control, the engine control unit recognises only an air/fuel mixture which is too rich (signal voltage approx. 800 mV) or an air/fuel mixture which is too lean (signal voltage approx. 100 mV). If the air/fuel mixture is too rich, the injection rate is reduced until the signal voltage indicates an air/fuel mixture which is too lean. The injection rate is now increased again.0.2 V/div.1 s/Div.Voltage [V] 0639_047Engine series EA211: signal characteristic of nonlinear oxygen sensor G39 upstream of the catalytic converter In the case of the EA211 engine series, the plot of the signal from the nonlinear oxygen sensor on the digital storage oscilloscope is approximately linear. Given that the engine control unit continuously evaluates the signals its receives, the signal characteristric is almost uniform and the signal voltage is approximately 450 mV.0.2 V/div.1 s/Div.Voltage [V] 0639_046Note The voltage values of the oxygen sensors can deviate from one manufacturer to another.31 BackForward Ξ ContentsServiceSpecial tools and workshop equipmentT10476A Extractor T10527 Release tool639_035639_036Installation aid for exact positioning when setting the trioval camshaft timing gear sprockets.For releasing the catches on the ventilation tube between the air filter housing and the throttle valve unit.32 BackForward Ξ ContentsMaintenance operationsInformation on required maintenance operations Quantity of motor oil inc. filter (change quantity) Motor oil standard Motor oil extraction permitted Service interval Interval or value 4.5 l VW 50400 (flexible oil change service) VW 50200 (fixed oil change service) No According to service interval display, between 15,000 km / 1 year and 30,000 km / 2 years depending on driving style and conditions of use. 90,000 km Lifetime 60,000 km / 6 years 60,000 km / 2 years Lifetime 210,000 km 210,000 kmAir filter change interval Fuel filter change interval Spark plug change interval Pollen filter change interval Ribbed V belt replacement interval Timing drive / toothed belt Timing drive tensioning systemNote The specifications in the current service literature generally apply. It is important to comply with the approved oil standard when changing the oil.33 BackForward Ξ ContentsAppendixGlossary↗ Austenitic cast steelAustenite is named after the British metallurgist Sir William Chandler Roberts-Austen. It is: • an allotrope of iron, a phase • a structural component of steel or cast iron↗ Roller burnishingRoller burnishing is chipless machining process involving the use of rollers. In the process a rolling tool is pressed against the workpiece under high pressure, with the result that the workpiece material begins to flow and is displaced. The tools (rolling discs) have a roughened surface. This process serves to smoothen and harden the surfaces of materials.↗ DLCDLC stands for Diamond Like Carbon, an amorphous carbon. These strata exhibit very high hardness and are noted for having very low dry coefficients of friction. They can be identified by their glossy, black-gray surface.↗ SENTThe SENT (Single Edge Nibble Transmission) data protocol can, in conjunction with the appropriate sensors, be used for digital data transfer as a substitute for analog interfaces.↗ Open-deck designThe open-deck design is characterised by the fact that the chamber enveloping the cylinder is open facing upwards. The coolant contained within the chamber is, therefore, effective in the highly stressed upper section of the cylinder, allowing the resultant heat to be dissipated over the entire height of the cylinder. This design also ensures significantly less warpage of the cylinders during installation of the cylinder head. One drawback is the reduced rigidity of the engine block. This effect can be compensated by using a metal cylinder head gasket. This design generally provides a good deal of scope for making the engine block manufacturing process more effective.↗ Spin-on oil filterIn spin-on oil filters the housing and the filter cartridge form a unit. They are replaced completely during servicing and maintenance. On the exterior, the can oil filters are very similar to one another. They may, however, differ in terms of their inner construction. Both the operating parameters and the design features of this group of filters have to be optimally adapted in order to ensure that the engine lubrication system functions properly. Particular attention must be given to the valves inside the filter because they are key to proper operation of the filter within the lubrication system.↗ PWM signalThe abbreviation PWM stands for pulse width modulated signal. This is a digital signal where one variable (e.g. electrical current) alternates between two values. The intervals between these alternations vary depending on activation. This allows digital signals to be transmitted.34 BackForward Ξ ContentsSelf study programmesYou will find further information on the technology of the 1.0l TFSI engine in the following self study programmes.SSP 384 The Audi 1.8l 4V TFSI Engine with Timing Chain Order number: A06.5S00.29.20SSP 477 Audi A1 Order number: A10.5S00.70.20SSP 616 Audi 1.2l and 1.4l TFSI engines of the EA211 series Order number: A12.5S01.00.20SSP 626 Basics of Audi engine technology Order number: A14.5S01.11.2035All rights reserved. Technical specifications are subject to change. Copyright AUDI AG I/VK-35 service.training@audi.de AUDI AG D-85045 Ingolstadt Technical status 07/15 Printed in Germany A15.5S01.24.20639Audi Vorsprung durch Technik