TECHNICAL DOCUMENTATION

SSP 642 Front final drive 0D4 in the Audi R8

PDFEN28 pages4 MB
SSP 642 Front final drive 0D4 in the Audi R8 - PDF cover

This PDF is currently unavailable.

Read document text
Self Study Programme 642 For internal use onlyFront final drive 0D4 in the Audi R8 (type 4S)Audi Service Training BackForward Ξ ContentsFront final drive 0D4Final drive 0D4 is used in an Audi for the first time in the Audi R8 (type 4S) and is a key component of the newly developed quattro powertrain for this vehicle. The quattro powertrain of the Audi R8 has the ability to adapt drive output (depending on driving situation and weather) to driving conditions, and to transfer up to 100 % to the front or rear axle. This gives better vehicle acceleration, provides good driving dynamics and improves driving stability. This distribution of drive torque or drive power is made possible by the electro-hydraulically operated all-wheel drive clutch in final drive 0D4. Audi drive select allows the driver to control the all-wheel drive clutch, and thus the distribution of torque and drive power between the front and rear axles. In addition, the optional performance mode of Audi drive select enables the all-wheel drive control unit to be adapted to the road conditions "dry", "wet" and "snow" for the first time. This means that the driver can configure the all-wheel drive control unit for extremely short reaction times. Final drive 0D4, in conjunction with Audi drive select, 7-speed dual clutch gearbox 0BZ (S tronic) and the high-performance 10-cylinder engines, enhances the Audi R8 driving experience in terms of power transmission.642_001Learning objectives of this self study programme:This self study programme provides you with information about front final drive 0D4. Once you have completed this self study programme you will be able to answer the following questions: • How is front final drive 0D4 designed and how does it work? • How do the software-assisted gearbox functions influence operation of the final drive and the vehicle. • What are the service guidelines for maintenance intervals and brake dynamometers?2 Contents_____________________________________________________________________________ 4 Distribution of drive power _________________________________________________________________________________________________________________________________ 6 Front axle lead _ _______________________________________________________________________________________________________________________________________________ 6System descriptionComponent overview_________________________________________________________________________8Cutaway view of gearbox__________________________________________________________________ 10 Longitudinal section A-A ___________________________________________________________________________________________________________________________________ 10 Front view ____________________________________________________________________________________________________________________________________________________ 11Gearbox oil supplies_ ________________________________________________________________________ 12 Axle oil (MTF) supply _______________________________________________________________________________________________________________________________________ 12 Haldex oil supply ____________________________________________________________________________________________________________________________________________ 13 Oil deterioration _ ____________________________________________________________________________________________________________________________________________ 13 Changing the oil _____________________________________________________________________________________________________________________________________________ 13All-wheel drive clutch_______________________________________________________________________ 14 Oil supply, lubrication and clutch cooling ________________________________________________________________________________________________________________ 14 Clutch control _______________________________________________________________________________________________________________________________________________ 16Cooling_ ____________________________________________________________________________________________ 18 Cooling circuit _______________________________________________________________________________________________________________________________________________ 18Function diagram_ _____________________________________________________________________________ 20 _ _____________________________________________________ 20All-wheel drive control unit J492 Sensors and actuators_ _____________________________________________________________________ 21 Hydraulic pressure sensor for all-wheel drive G942 _____________________________________________________________________________________________________ 21 Haldex clutch pump V181 _ _________________________________________________________________________________________________________________________________ 21Audi drive select_______________________________________________________________________________ 22Operating situations_________________________________________________________________________ 22 Launch control program ____________________________________________________________________________________________________________________________________ 22 Torque vectoring ____________________________________________________________________________________________________________________________________________ 22 Coasting mode ______________________________________________________________________________________________________________________________________________ 23Service_ _____________________________________________________________________________________________ 24 Using the diagnostic tester ________________________________________________________________________________________________________________________________ 24 Maintenance and change intervals ________________________________________________________________________________________________________________________ 24 Brake test ____________________________________________________________________________________________________________________________________________________ 24 Towing _ _______________________________________________________________________________________________________________________________________________________ 25 Gearbox warning lights _____________________________________________________________________________________________________________________________________ 25 Limp-home concept _ ________________________________________________________________________________________________________________________________________ 25Appendix_ __________________________________________________________________________________________ 26 Test your knowledge ________________________________________________________________________________________________________________________________________ 26The Self Study Programme teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a Repair Manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. This content is not updated. For further information about maintenance and repair work, always refer to the current technical literature.!NoteReference3 BackForward Ξ ContentsSystem descriptionFinal drive 0D4 and the 7-speed dual clutch gearbox 0BZ provide the basis for the quattro powertrain of the Audi R8 (type 4S). The 7-speed dual clutch gearbox transmits the engine torque and makes this torque available to the front and rear axles. The vehicle is primarily driven through the rear axle. The rear axle is able to transmit all available drive power, provided that a portion of the drive power is not transferred to the front axle through the all-wheel drive clutch in final drive 0D4. To assist the active distribution of drive torque and drive power, the mechanical limited slip differential of the rear axle has been reconfigured. The drive power for the front axle is transferred through the gearbox output shaft. The reduction ratio of the gearbox output shaft is such that the circumferential speed of the front wheels is slightly higher than the circumferential speed of the rear wheels. This difference is referred to hereinafter as "lead". Depending on the driving situation, it is the basis for the controlled transfer of up to 100 % of drive torque (drive power) to the front axle. Refer to page 7. The all-wheel drive clutch of the newly developed front final drive takes off the torque for driving the front axle from the gearbox output shaft through the prop shaft, the central shaft and the all-wheel drive clutch input shaft. At the same time, it transfers up to 550 Nm to the differential pinion shaft. In a hydrodynamic and complex process, the all-wheel drive control unit decides how much torque is to be transferred. The torque to be transmitted by the all-wheel drive clutch is generated by the all-wheel drive control unit by activation of the Haldex clutch pump V181. The all-wheel drive control unit also factors in the coefficients of friction in the all-wheel drive clutch while making allowance for oil deterioration. The all-wheel drive control software and the programmed values for oil deterioration are stored in the all-wheel drive control unit J492. The all-wheel drive system is controlled on the basis of extensive operating status recognition information. Information from sources including the ESC, engine and gearbox control units is utilised for this purpose. The distribution of drive power as defined by default parameters is pre-controlled in dependence on the vehicle's operating status. If necessary, the pre-control process may be overridden by other control processes. The Audi drive select modes and about 130 different signals including signals for ambient conditions, axle load distribution, driver input, longitudinal acceleration, yaw rate, transverse acceleration, steering angle, vehicle speed, engine torque and gear ratio - are incorporated into the all-wheel drive control process. The distribution of drive power to the front and rear axles has a significant influence on the traction, driving dynamics and driving stability of the Audi R8. The positive effect of the all-wheel drive clutch control unit is explained on page 6.Selector mechanismFront final drive 0D4Central shaftAll-wheel drive control unit J492 Refer to page 204 BackForward Ξ ContentsRear axle limited slip differential7-speed dual clutch gearbox 0BZ642_002Prop shaft Spline for dual mass flywheel – gearbox input Drive shaft Gearbox output shaft −− Front final drive input shaft −− PTO shaft (power take-off)!Note For further information about 7-speed dual clutch gearbox 0BZ and the rear axle limited slip differential, please refer to SSP 643.5 BackForward Ξ ContentsDistribution of drive powerThe 10-cylinder engines of the Audi R8 (type 4S) have the ability to output between 540 Nm and 560 Nm of peak torque to the 7-speed dual clutch gearbox 0BZ. If the rear axle puts down its full drive power in 4th gear and at peak engine torque, approximately 3000 Nm of torque is applied. Irrespective of the engine torque and selected gear, the all-wheel drive clutch can take off a portion of the available drive power in a controlled manner. In this way, up to 550 Nm of torque are transferred to the differential pinion shaft. Refer to page 11. The reduction ratio of the differential produces up to 1500 Nm of torque at the front axle. 1500 Nm at the front axle corresponds to approximately 45 % of drive power in 4th gear and at full engine torque. The extent to which the variable range of the all-wheel drive clutch can influence the distribution of drive power between the front and rear axles depends on the engine torque and the driveline ratios. Depending on the engine torque and selected gear, up to 100 % of drive power can be transferred to the front axle due to the front axle lead. The all-wheel drive control unit decides how much torque is to be transferred from the all-wheel drive clutch to the pinion shaft.Front axle leadThe gear ratios of the driveline are such that the circumferential speed of the front wheels is slightly higher than the circumferential speed of the rear wheels. This configuration is referred to as "front axle lead". Due to this lead effect, wheel speeds are continously compensated in the all-wheel drive clutch. The associated speed differential is the basis for exact clutch control. The clutch is operated with zero backlash. This permits very short reaction times during closing of the clutch. Zero-backlash operation of the clutch results in a very small amount of drag torque. Refer to page 10. The speed compensation effect and the drag torque resulting from the lead of the front axle produce frictional heat in the clutch. To dissipate the heat which is generated, the clutch and the final drive are cooled. Refer to pages 14 and 18. Depending on the engine torque and driveline ratios, the lead also allows more than 50 % of drive power to be transferred to the front axle, improving driving dynamics and driving stability. Reducing the longitudinal force on an axle allows the axle to absorb more lateral force.Longitudinal force Rear axle 80 %Front axle 20 %Initial scenario This can be illustrated by an initial scenario where 20 % of drive power is transmitted from the front axle and 80 % from the rear axle in a controlled manner. Conversely, the lateral force which can be transmitted by the front axle is proportionately greater than the lateral force which can be transmitted by the rear axle. If the vehicle incurs critical oversteer in this situation, it can be stabilised by transferring drive power towards the front axle.Longitudinal slip λLateral force642_0176 BackForward Ξ Contentsλ FA Longitudinal forceλ RALongitudinal slip λRear axle 50 % Front axle 50 %Lateral forceLongitudinal slip λ642_018Stabilisation without front axle lead If the vehicle does not have front axle lead, i.e. the front and rear wheels spin at the same circumferential speed, front axle drive power can be increased to a maximum of 50 %, if necessary. If the rear axle transmits more torque (drive power) than the front axle, there is more slip at the rear wheels. Due to the greater amount of slip at the rear wheels, wheel speeds are compensated in the all-wheel drive clutch, allowing the torque of the all-wheel drive clutch to be increased still further. This is possible until the front axle transmits the same amount of drive power as the rear axle. Given that the front and rear wheels can have equal amounts of slip, wheel speeds are not compensated in the all-wheel drive clutch. It makes no sense to further increase the pressure on the multi-plate clutch with plates rotating at the same speed because it is not possible to transmit more torque to the front axle. Equal amounts of lateral force can be transmitted to the front and rear axles. The lateral force which can be transmitted to the rear axle has increased compared to the initial scenario. This counteracts oversteer.λ FAλ RALongitudinal slip λLongitudinal force Front axle 70 %Rear axle 30 % Lateral force Longitudinal slip λStabilisation with front axle lead The lead of the front axle enables front axle drive power to be increased to over 50 %. Due to the lead of the front axle, wheel speeds are compensated in the all-wheel drive clutch even if the drive power split is 50/50. This allows the amount of torque transferred to the front axle to be increased still further. Depending on the engine torque and gear ratio, up to 100 % of drive torque (drive power) is available. The amount of lateral force which can be transmitted by the front axle is consequently less than the amount of lateral force which can be transmitted by the rear axle. If the vehicle incurs critical oversteer in this situation, it can be stabilised much more effectively than a vehicle without front axle lead.λ FAλ RALongitudinal slip λ642_0197 BackForward Ξ ContentsComponent overviewThe component overview largely reflects the components which can be replaced during repair work.Cross-member bolt Front final driveFront cross-member for front final drive Bracket with rubber metal bearing, bolted to body Shaft oil sealSplined flange shaftSnap ring Vent for all-wheel drive clutch oil supply Sealing surface, sealed with liquid sealantOutlet port for pressure relief valve and vent port for pump sump of Haldex clutch pump V181All-wheel drive clutch Pressure relief valveFinal drive with open differential Vent Final drive / differentialO-ringCoolant connectionCooling channel plateO-ring Hydraulic pressure sensor for all-wheel drive G942 Hydraulic temperature sensor for all-wheel drive G943 O-ringThree-point bearing The final drive is connected to the vehicle body by a three-point bearing. The front cross-member is held in place by 2 brackets with rubber-metal bearings. The elongated housing of the central shaft helps to support the torque of the final drive. It is connected to the rear cross-member of the final drive by a rubber-metal bearing. A final drive which is not installed without stress can cause vibration and noise. During repair work always refer to the instructions in the Workshop Manual.O-ringsHaldex clutch pump V181 with wiring kit for G942 and G9438!Note If the "central shaft housing / all-wheel drive clutch / final drive" bolt is removed, the seal between the final drive and the all-wheel drive clutch must be replaced with the liquid seal specified in the Electronic Parts Catalogue (ETKA). BackFitting the prop shaft The prop shaft transmits drive torque to the central shaft by means of a spline. A bellows prevents the ingress of dirt and moisture into the spline. The bellows must be properly fitted as shown in the diagram. Follow the fitting instructions given in the Workshop Manual.Forward Ξ ContentsBellows sealAnti-dust ring Ball bearing Snap ring Anti-dust ringRetaining bead engages circumferential grooveRubber-metal bearing"Central shaft housing / all-wheel drive clutch / final drive" bolt Prop shaftTo reduce imbalance, there is a coloured mark on the central shaft and on the prop shaft. The two marks must be matched up as closely as possible during assembly.Bellows seal Central shaft housing Central shaftProp shaft642_003Front cross-member for front final drive9 BackForward Ξ ContentsCutaway view of gearboxLongitudinal section A-AAnti-dust ring Snap ring Ball bearing Anti-dust ring Central shaft Central shaft housingRubber-metal bearingMulti-plate clutchZero-backlash clutch operation The all-wheel drive clutch is a multi-plate clutch. A diaphragm spring presses the clutch piston against the clutch plates, with the result that the clutch is free of backlash. This permits very short control times during closing of the clutch. Zero-backlash operation results in a small amount of drag torque if the clutch is not activated. To dissipate the resultant frictional heat, the clutch is cooled by the mechanical oil pump. Refer to page 14.Clutch piston with axial bearing Pressure relief valveDiaphragm springVent for final drive / differential Final drive with open differentialPinion shaft – all-wheel drive clutch output shaft Vent for all-wheel drive clutch oil supply642_005Mechanical oil pumpAll-wheel drive clutch input shaft Hydraulic pressure sensor for awd G942 Haldex clutch pump V181 Double shaft oil seal10Coolant connection, supplyHydraulic temperature sensor for all-wheel drive G943Electrical plug connection BackMechanical powered oil pump Pressure relief valve Shaft oil seal All-wheel drive clutch housing Clutch piston with axial bearing Multi-plate clutch Vent for all-wheel drive clutch oil supply Front final drive housingForward Ξ ContentsVent Final drive/differential642_004O-ringsGasket Pump sump for V181Cooling ductDifferential/non-locking differential Cooling channel plateCoolant connection Pinion shaft – all-wheel drive clutch output shaft Double shaft oil seal Pump sump for mechanical powered oil pumpHaldex clutch pump V181 All-wheel drive clutch input shaftHaldex oil supply Axle oil (MTF) supplyIntake port for mechanical powered oil pumpAFront viewVent for final drive / differential Differential coverSplined flange shaft, leftSplined flange shaft, rightCoolant connection, supplyACooling channel plateCoolant connection, return642_00611 BackForward Ξ ContentsGearbox oil suppliesFinal drive 0D4 has 2 independent oil supplies with separate oil chambers: the axle oil supply and the Haldex oil supply.Axle oil (MTF) supplyThe oil chamber for the axle oil (MTF, Mechanical Transmission Fluid) is located in the front section of the final drive housing. A double shaft oil seal defines the boundaries of this chamber and seals it off against the Haldex oil. An oil drainage port stops oil flowing to the other side in the event of a leak. Refer to Fig. 642_004.Pressure relief valve All-wheel drive clutch housingCentral shaft housingOutlet port for pressure relief valve and vent for pump sump of Haldex clutch pump V181Vent for all-wheel drive clutch oil supplyCentral shaftMechanical powered oil pump All-round groove: connects outlet port to overflow port Overflow port for pump sump of Haldex clutch pump V181 leading into pump sump for mechanical pumpSealing face"Central shaft housing / all-wheel drive clutch / final drive" boltHaldex oil supply Axle oil (MTF) supplyHaldex clutch pump V181Filler screw – Haldex oilDrain screw – Haldex oil12 BackForward Ξ ContentsHaldex oil supplyThe Haldex oil chamber is located in the rear section of the final drive housing This boundaries of the oil chamber are defined by the all-wheel drive clutch housing. The sealing face between the all-wheel drive clutch housing and the front final drive housing is sealed with liquid sealant. If the central shaft has to be removed for servicing, it is no longer possible to guarantee proper sealing between the all-wheel drive clutch and the front final drive housing due to the removal of the "central shaft housing / all-wheel drive clutch / final drive" bolt. In this case, the gasket must be replaced. Use the liquid sealant specified in the Electronic Parts Catalogue (ETKA) for this purpose. The Haldex oil chamber houses the intake chambers or pump sumps for the mechanical powered oil pump and Haldex clutch pump V181. The pump sump for the mechanical powered oil pump is integrated in the front final drive housing. The pump sump for the Haldex clutch pump V181 is integrated in the all-wheel drive housing. It is vented from the overflow port via the round groove which leads to the vent port and into the front final drive housing. For further information about the Haldex oil supply, refer to "Hydraulic diagram" on page 14.Oil deteriorationDue to exposure to shear forces and high temperatures, the Haldex oil is subject to deterioration which affects friction levels within the all-wheel drive clutch. To adapt the all-wheel drive control unit to the friction levels, the changing friction levels are stored in the control unit as "programmed values for oil deterioration".Changing the oilFollow the instructions given in the Workshop Manual and on the diagnostic tester for checking and changing the oil in both supplies. Given that the drain, filler and inspection screws of both oil supplies are positioned very close to one another, there is a possibility of mix-up. Using the wrong oil will cause irreparable damage to the components. If you change the Haldex oil, the quantity of oil specified in the Workshop Manual must be replenished. The bottom edge of the Haldex oil filler screw thread is not a check mark. Also reset the programmed values for oil deterioration (ageing) in the all-wheel drive control unit using the "changing high-performance oil for Haldex clutch" function on the diagnostic tester. Refer to "Maintenance and change intervals" on page 24.Vent for final drive / differential Double shaft oil seal Leak oil drainage port Front final drive housing642_007Coolant connection, supplyAxle oil drain screwAxle oil filler and inspection screw13 BackForward Ξ ContentsAll-wheel drive clutchOil supply, lubrication and clutch coolingThe all-wheel drive clutch is supplied by 2 pumps: by a mechanical powered oil pump and Haldex clutch pump V181. Each pump has its own circuit with its own pump sump. The pump sump for the mechanical powered oil pump is integrated in the front final drive housing. The all-wheel drive clutch housing seals off the Haldex oil supply system. Refer to page 13. The pump sump for Haldex clutch pump V181 is integrated in the all-wheel drive clutch housing. It is filled by the mechanical powered pump. The circuit of the mechanical powered pump is continuously active during vehicle operation. The circuit of the Haldex clutch pump V181 is demand controlled by the all-wheel drive control unit J492. In this case, the circuits operate in parallel.Pinion shaft splineCooling oil for multi-plate clutchCooled multi-plate clutchAll-wheel drive clutch housingOil supply for the pump sump of Haldex clutch pump V181Input shaft – all-wheel drive clutch, driven by prop shaft via central shaft Mechanical powered oil pump Pressure side of pumpPump intake side642_008Intake port for the mechanical powered oil pumpAxial piston pump with centrifugal pressure governorPump sump for Haldex clutch pump V181Maximum Haldex oil level in pump sump of Haldex clutch pump V181Haldex clutch pump V181 (refer to page 21)!14Note To fill the pump sump for Haldex clutch pump V181 after carrying out repairs, the removed final drive can be swivelled back as directed in the Workshop Manual after replenishing the Haldex oil. An alternative is to drive the completed vehicle on public roads for approximately 2 km. The diagnostic tester also provides directions regarding this measure. When the vehicle is driven, the mechanical powered oil pump fills the pump sump up to the maximum Haldex oil level. Refer to Fig. 642_008. BackMechanical powered oil pump circuitForward Ξ ContentsCooling oil for multi-plate clutchMulti-plate clutchMechanical powered oil pumpAll-wheel drive clutch input shaftAll-wheel drive hydraulic temperature sensor G943642_009Cooling oil flow and oil supply for pump sump V181 Pump sump Pump sump for Haldex clutch pump V181 Pump sump for mechanical powered oil pumpMechanical powered oil pump The mechanical powered oil pump is an internal gear pump. The pump starts to run when the vehicle begins to roll forwards. The inner rotor of the pump interlocks with the all-wheel drive clutch input shaft. The all-wheel drive clutch input shaft is driven by the central shaft via the prop shaft, the drive shaft and the gearbox output shaft of 7-speed dual clutch gearbox 0BZ. Refer to page 5. The task of the mechanical powered oil pump is to fill the sump for the Haldex clutch pump V181, as well as ensuring that the components are lubricated and supplying the multi-plate clutch with cooling oil.Cooling is essential due to the frictional heat produced by zerobacklash operation of the clutch. Refer to page 18. During initial operation of the final drive or if repair work is needed, the pump sump for Haldex clutch pump V181 stays dry after replenishing the Haldex oil. To prevent the pump from running dry, the pump sump for Haldex clutch pump V181 must be filled. Refer to notes on page 14.Hydraulic temperature sensor for all-wheel drive G943 For further information refer to page 21.15 BackForward Ξ ContentsClutch controlIf the Haldex clutch pump V181 is activated via the all-wheel drive control unit, it takes in Haldex oil from its sump and conveys it into the clutch piston pressure chamber. Zero-backlash operation of the clutch permits short reaction times during pressure build-up and, therefore, also during transmission of the desired amount of clutch torque. This ensures excellent driving dynamics.Clutch piston with axial bearingMulti-plate clutchPressure chamberAll-wheel drive clutch housingOutlet port for pressure relief valve and vent port for pump sump of Haldex clutch pump V181 Pressure relief valve, opens at P 44 barPress. side of pump642_010Axial piston pump with centrifugal pressure governor Diaphragm spring in clutch piston pressure chamber Pump sump for Haldex clutch pump V181, pump intake side Maximum Haldex oil level in pump sump of Haldex clutch pump V181 Haldex clutch pump V18116 BackCircuit of Haldex clutch pump V181Pressure chamber Haldex clutch pump V181 Clutch pistonForward Ξ ContentsMulti-plate clutchHydraulic pressure sensor for all-wheel drive G942Pressure relief valveP  44 bar642_011Hydraulic operating pressure Outlet port Pump sump / depressurised Intake line / vacuum Pump motor Axial piston pump Centrifugal pressure governor Pump sump for Haldex clutch pump V181Haldex clutch pump V181 The Haldex clutch pump V181 produces hydraulic pressure in the all-wheel drive clutch. It consists of a pump motor and the axial piston pump with centrifugal pressure governor. The hydraulic pressure in the clutch piston pressure chamber is regulated by the centrifugal pressure governor based on the speed of the pump motor. The pump motor is driven by the all-wheel drive control unit J492. The functional principle of the Haldex clutch pump V181 is identical to that of the fifth-generation Haldex clutch. The axial piston pump and the centrifugal pressure governor are described in SSP 609 from page 44. The circuit of the Haldex clutch pump V181 is highlighted in grey in Fig. 642_011. Hydraulic temperature sensor for all-wheel drive G943 The pressure sensor measures the hydraulic pressure for the clutch piston and thus monitors the capacity of pump V181 indirectly. If the pump runs dry, it has no pumping capacity and is shut down for its protection. Refer to page 21.Venting the pressure chamber: During initial operation of the final drive or if repair work is needed, it is important to make sure that the pump sump for the Haldex clutch pump V181 is filled. Refer to notes on page 14. This prevents the pump from running dry. The clutch piston pressure chamber then needs to be vented using the "ventilation and hydraulic leak test" function on the diagnostic tester. Refer to page 24. This function allows the Haldex clutch pump V181 to build up a pressure of over 44 bar and vents the air in the pressure chamber through the pressure relief valve. Pump operation is clearly audible because the pump runs at maximum load during the ventilation phase.17 BackForward Ξ ContentsCoolingCooling circuit810 511 6 79432Coolant circuit for cooling the final drive during the warm-up phase1Heater matrix Heater matrix return line1 Heater matrix supply line 2 Heater matrix 3 Flow restrictor 4 Cooling duct plate 5 T piece 6 Coolant thermostat for engine oil cooler 7 Bypass 8 L/H auxiliary radiator for engine oil cooling (air to water) 9 Engine oil cooler 2 (water to oil) 10 Continued coolant circulation pump V51 11 Coolant thermostatHeater matrix supply lineFrom heater matrixCooling channel plate18 BackTo ensure that the all-wheel drive is fully functional in all driving situations and to counteract oil deterioration (refer to page 13), the frictional heat of the multi-plate clutch is dissipated through the cooling oil made available by the mechanical powered oil pump. The cooling oil flows through the multi-plate clutch (refer to page 14, Fig. 642_008) and is discharged into the pump sump for the mechanical powered oil pump. To cool the Haldex oil which is used as cooling oil in the pump sump, coolant flows through the cooling duct plate from the return line of the heater matrix. The axle oil (MTF) supply is cooled in addition to the Haldex oil supply. A flow restrictor within the circuit ensures that sufficient coolant is diverted.Forward Ξ ContentsThe cooling circuit on page 18 shows the path of the coolant for cooling the final drive directly after engine starting. Upwards of a temperature of 95 °C, the coolant thermostat for engine oil cooler (6) directs the coolant via the L/H auxiliary radiator for engine oil and engine oil cooler 2. In this case, coolant does not flow through the bypass branching off from coolant thermostat of the engine oil cooler. For a detailed diagram of the cooling circuit for the Audi R8 (type 4S), refer to SSP 641 on page 38.BypassL/H auxiliary radiator for engine oil cooling (air to water)To coolant thermostat for engine oil coolerCoolant thermostat Continued coolant circulation pump V51 Flow restrictorEngine oil cooler 2 (water to oil) Coolant thermostat for engine oil coolerCoolant return from the cooling duct plateCoolant supply to cooling duct plate642_01319 BackForward Ξ ContentsFunction diagramChassis CAN highJ492Chassis CAN lowKey: G943 Ground cable Positive cable Signal line G942 G942 Hydraulic pressure sensor for all-wheel drive G943 Hydraulic temperature sensor for all-wheel drive J492 All-wheel drive control unit V181 Haldex clutch pump V181642_014All-wheel drive control unit J492Diagnosis: • The electrical wiring is checked for open circuit as well as for short circuit to ground and positive. • Data exchange across the CAN bus is monitored. • The parameters for adaptation to engine power output are checked. • The vehicle identification number can be checked for plausibility. If the all-wheel drive control unit or the onboard power supply control unit is interchanged and not programmed, an entry will be registered in the event memory. • The main processor of the control unit is diagnosed. • The temperature of the control unit is monitored. • The whele speed signals are checked for plausibility. In the driver adopts a highly dynamic driving style, this can trigger a sporadic event memory entry (albeit not an entry indicating an actual fault) on wet and icy road surfaces affording little friction. • The all-wheel drive clutch function is checked for plausibility. If the Haldex clutch pump V181 is activated, a pressure must be measurable inside the pressure chamber and torque must be transmitted. • The temperature of the clutch plates is measured using, among other things, the Haldex oil temperature measured with the aid of the all-wheel drive hydraulic temperature sensor G943. If a default value is exceeded as a result of high power demand, a message to this effect is displayed in the instrument cluster and, in accordance with a limp-home concept, the all-wheel drive clutch is not activated further until the Haldex oil has cooled down again.The all-wheel drive control unit J492 is located behind the luggage compartment tray adjacent to the starter battery. It houses the software for the all-wheel drive 642_020 control unit. A control unit version is available for all engine versions. Its software is adapted at the factory on the basis of engine power parameters. The control unit and the recorded programming values are assigned to the vehicle on the basis of the vehicle identification number. When the control unit is replaced, it is important to follow the instructions given by the "Replace control unit" function available via address code 22 on the diagnostic tester (refer to page 24). The function includes all steps to be performed after the control unit is replaced. The vehicle identification number, performance-specific parameters and programmed values can be deleted using the "Basic setting" function. Data exchange and power supply: refer to function diagram.20 BackForward Ξ ContentsSensors and actuatorsThe two hydraulic pressure sensors of the all-wheel drive clutch and the Haldex oil temperature allow highly precise all-wheel drive control while extending the diagnostic options as well as improving component protection.All-wheel drive clutchHydraulic pressure sensor for all-wheel drive G942The hydraulic pressure sensor for all-wheel drive G942 measures the hydraulic pressure in the pressure chamber of the clutch piston. The measured value is used to control the clutch and to determine the deterioration of the oil. The measured value also helps protect the Haldex clutch pump V181 against running dry. If no pressure is measurable when the Haldex clutch pump V181 is activated, an entry is registered in the event memory and the pump stops running. A corresponding message is displayed in the instrument cluster. The pumping capacity of the pump must be checked after repairs are carried out. If the hydraulic pressure sensor is replaced, the offset value stored in the all-wheel drive control unit J492 for the old pressure sensor must be deleted using the basic settings function of the diagnostic tester. Diagnosis: • The electrical wiring is checked for open circuit as well as for short circuit to ground and positive. • Plausibility criterion: When the Haldex clutch pump V181 is activated, a pressure must be measurable inside the pressure chamber. Substitute signal: • there is no substitute signal, refer to "Limp-home concept" on page 25.G942Pressure chamberG943642_021Hydraulic temperature sensor for all-wheel drive G943The hydraulic temperature sensor for all-wheel drive G943 measures the temperature of the Haldex oil in the pump sump of the mechanical powered pump. The measured value is used to determine the deterioration of the oil and helps prevent the clutch from overheating. Diagnosis: • The electrical wiring is checked for open circuit as well as for short circuit to ground and positive. • Plausibility criterion: if the temperature of the Haldex oil exceeds the limit, the all-wheel drive clutch is not activated further. Substitute signal: • there is no substitute signal, refer to "Limp-home concept" on page 25.Haldex clutch pump V181The Haldex clutch pump V181 produces hydraulic pressure in the all-wheel drive clutch. Refer to page 17. The wiring kit for the Haldex clutch pump V181 also contains the wiring for the hydraulic pressure sensor for all-wheel drive G492 and the hydraulic pressure sensor for all-wheel drive G493. Diagnosis: • The electrical wiring is checked for open circuit as well as for short circuit to ground and positive. • Plausibility criterion: when the Haldex clutch pump V181 is activated, a pressure must be measurable inside the pressure chamber. Actuator test: refer to page 24. • "All-wheel drive clutch function test" • "Ventilation and hydraulic leak test" Checking the pumping capacity of the pump: • Is the pump sump for Haldex clutch pump V181 filled? Refer to notes on page 14. • Carry out "all-wheel drive clutch function test". • Carry out "ventilation and hydraulic leak test" and check final drive for leaks (visual inspection).Haldex clutch pump V181 with wiring kit for G942 and G943642_02221 BackForward Ξ ContentsAudi drive selectThe driver can use the Audi drive select button to select between the "comfort", "auto", "dynamic" and "individual" modes. These modes influence the all-wheel drive control setup with respect to the distribution of drive power between the front and rear axles. The Performance button sets the "performance" mode and selects the last active setup (last mode), i.e. snow, wet or dry. Setups can be selected using the adjustment ring. In snow, wet and dry modes the pre-control values for road surface friction are set to within narrower bounds. The all-wheel drive control unit, which continuously measures the friction coefficients of the road surface, is able to react more quickly and with greater precision thanks to more specific pre-control values. This improves vehicle handling on dry, wet and snow-covered roads and provides more sporty driving dynamics. All-wheel drive control setups available using Audi drive select comfort In "comfort" mode the distribution of drive power is front axleorientated. Cornering behaviour is neutral tending to slight understeer at the limits of dynamic performance. auto In "auto" mode drive power is evenly distributed between the front and rear axles. Handling is neutral during cornering. This is how an Audi without Audi drive select would be set up.Performance button with adjusting ring for selecting the snow, wet and dry modes642_025dynamic In "dynamic" mode the distribution of drive power is rear-orientated. Handling is more sporty and cornering behaviour is neutral tending to slight oversteer at the limits of dynamic performance. individual In "individual" mode the driver can choose gearbox and all-wheel drive setups independently of other vehicle systems. performance In "performance" mode drive power is evenly distributed between the front and rear axles, as is the case in "auto" mode.Audi drive select button!Note Activating the "performance" mode limits the range of the ESC and TCS stabilisation functions. Only activate performance mode if you have the necessary driving skills and the traffic conditions permit – danger of skidding.Reference For further information about Audi drive select and how the performance of the Audi R8 (type 4S) is affected, refer to the Owner's Manual and SSP 641.Operating situationsCertain operating situations affect all-wheel drive control. The main operating situations are set out below and explained in the following table.Launch control programThe Launch Control Program regulates the maximum acceleration of the vehicle from a standing start. The all-wheel drive clutch delivers the maximum possible amount of torque for the front axle. Refer to the Owner's Manual for operating instructions and other information. Controlled braking intervention builds up stabilising torque at the wheels under increased load on the outside of the curve, allowing more drive power to be transmitted from the wheels under reduced load on the outside of the curve. In addition to providing an dynamic axle load distribution, torque vectoring affects the maximum amount of drive power which can be transmitted by the front axle and therefore is incorporated into the all-wheel drive control process. For more information about the torque vectoring system, refer to SSP 617, page 24 ff.Torque vectoringTorque vectoring is a software function of the ESC control unit. During cornering at high speeds, the ESC control unit determines the reduced load on the wheels on the inside of the curve and the increased load on the wheels on the outside of the curve.22 BackForward Ξ ContentsCoasting modeIn coasting mode the all-wheel drive clutch of front final drive 0D4 is open. Coasting mode is set by opening the momentarily engaged clutch in 7-speed dual clutch gearbox 0BZ. In this way the engine is disengaged from the gearbox. The vehicle does not enter overrun mode as it usually does, but rather rolls without any engine braking effect and utilises the kinetic energy of its motion. Fuel can be saved by adopting an anticipatory driving style. If the operating conditions for coasting mode (refer to SSP 641 page 4) are met, the gearbox activates coasting mode. Coasting mode can be activated manually in the highest gear by operating the Tip + selector paddle. The Tip- and Tip+ shift paddles can be used to shift at random between overrun mode and coasting mode within the above parameters.This table summarises the torque requirements and the states of the all-wheel drive clutch for each of the listed operating situations.Operating situationsRequired front axle torque highState of all-wheel drive clutch up to maximum torque / maximum pressure depending on driving situationSpeed differential between front and rear axles low because clutch is closed to maximise traction dynamic driving style: low because the clutch is closed conservative driving style: medium, resulting primarily from the axle ratiosAcceleration, kickdown, Launch Control Program Fast drivingdepending on driving situationDriving on a slippery surface Coasting mode, coasting Parkingdepending on driving situationdepending on driving situation open low contact pressuredepending on driving situation, tending to low to achieve good traction0 Nm lowlow, defined by the design and dependent on the curve radii of the front and rear axles All-wheel drive clutch open, differential speed is not influenced by the all-wheel drive When the vehicle is stationary, the clutch is proactively closed if a subsequent acceleration phase is predicted.Braking0 NmopenStoppingdepending on driving situationdepending on driving situationDownhill assist Hill Start Assist Driving with an emergency wheel Towingdepending on driving situation depending on driving situation depending on driving situation 0 Nmdepending on driving situation depending on driving situation depending on driving situation open if the engine is not running and no gear is selected ** open* low to medium low because vehicle is only allowed to be towed on 4 wheels directly dependent on driving speed if single axle roller is used (high differential is possible)Brake test0 Nm* Before checking the brakes on the dynamometer, activate driving position N. Refer to SSP 641, page 48. In driving position N the all-wheel drive clutch is open.** Before towing the vehicle, the parking lock emergency release mechanism must be activated. Refer to SSP 641, page 52.23 BackForward Ξ ContentsServiceUsing the diagnostic testerThe all-wheel drive control unit can be selected with the vehicle diagnostic tester via address code 22. The event memory of the control unit can be read out using the self-diagnostics.The following guided functions can be activated: • Control unit identification • Read measured data • Basic setting • Reset to factory settings of control unit manufacturer: this function deletes all programmed values. The control unit must be re-initiated. Advantage: with this function, the control unit can be interchanged. • Reset programmed values for oil deterioration: if the Haldex oil is changed in the course of routine servicing, the programmed values for oil deterioration must be reset. • Reset the offsets of hydraulic pressure sensor – G492: if the hydraulic pressure sensor is replaced, the offset value must be reset. • Cancel and exit program • Actuator diagnostics • All-wheel drive clutch function test: if the function is active, the all-wheel drive clutch is closed up to a speed of 10 kph. Driving the vehicle with the allwheel drive clutch closed noticeably increases the strain on the driveline at medium steering lock. The vehicle begins to shudder. If the vehicle reaches a speed of 10 kph, the allwheel drive clutch opens and a jolt is noticeable when the driveline is relieved of load. The jolt which occurs when the driveline is relieved of load is a general indication that the all-wheel drive is functioning. • Ventilation and hydraulic leak test. This function allows the Haldex clutch pump V181 to build up a pressure of over 44 bar and vents the air in the pressure chamber via the pressure relief valve. Pump operation is clearly audible because the pump runs at maximum load during the ventilation phase. • Cancel • Replace control unit • The programmed values from the old control unit are read out. If the old control unit can no longer be addressed, the programmed values for oil deterioration and pressure sensor offset cannot be read out and transmitted. In this case, the Haldex oil must be changed. • The control unit to be initialised reads in the vehicle identification number via the chassis CAN after the first terminal change and is assigned to the vehicle. • The basic software of the new control unit is supplied with the performance-specific parameters. • The programmed values of the old control unit are transferred. • Changing high-performance oil for Haldex clutch The programmed values for oil deterioration are reset. • Check SVM control unit configuration The validity of the software and the performance-specific parameters are checked and adapted to suit the vehicle.Maintenance and change intervalsThe Haldex oil and the axle oil currently have a servicing and change interval of 180,000 km or 10 ten years. Refer to the instructions given in the Workshop Manual. The bottom edge of the Haldex oil filler screw thread is not a check mark. If the Haldex oil is changed, the quantity of oil specified in the Workshop Manual must be replenished. Reset the programmed values for oil deterioration (ageing) in the all-wheel drive control unit using the "changing high-performance oil for Haldex clutch" function on the diagnostic tester. Note: mixing up the two oil supplies will cause irreparable component damage. Refer to "Changing the oil", page 13.Brake testBefore checking the brakes on the dynamometer, activate driving position N. Refer to SSP 641, page 48. In driving position N, the all-wheel drive clutch is open.24 BackForward Ξ ContentsTowingBefore towing the vehicle, the parking lock emergency release mechanism must be activated. Refer to SSP 641, page 52. The vehicle may only be towed with both axles on the ground. Towing the vehicle with the front axle raised would damage the front final drive and therefore is not permitted. Maximum towing distance is 50 km. Maximum towing speed is 50 kph.Gearbox warning lightsIf the yellow gearbox warning light appears in the instrument cluster, it is normally possible to continue driving the vehicle. Driver information is displayed informing the driver what to do.642_023If the red gearbox warning light appears in the instrument cluster, the driver is instructed not to drive any further.642_024Limp-home conceptThe all-wheel drive system initiates different limp-home programs depending on the nature of the fault. • If certain signals cannot be registered, the driving dynamics control system may not be fully functional. In this case the all-wheel drive clutch is only activated to a limited degree in order to improve traction. • In the event of serious faults, the all-wheel drive system is deactivated. • If a defined temperature value is exceeded under very high power demand, the all-wheel drive system is no longer be activated.In all cases, warnings are displayed in the instrument cluster.25 BackForward Ξ ContentsAppendixTest your knowledgeAll of the following questions may have one or more correct answer.Question 1: The all-wheel drive clutch of front final drive 0D4 is a ...?a) Hydrodynamic viscous coupling b) Electronically controlled multi-plate clutch c) Electronically controlled dry plate clutchQuestion 2: What is the maximum amount of torque which the all-wheel drive clutch can transmit to the differential case of the front final drive?a) approx. 550 Nm b) approx. 8400 Nm c) approx. 1500 NmQuestion 3: What proportion of drive power can the all-wheel drive clutch transmit to the front axle in 4th gear and at maximum engine torque?a) 45 % b) 100 % c) 50 %Question 4: On which factors is the maximum proportion of drive power which the all-wheel drive clutch can transmit to the front axle not dependent?a) Selected gear b) Engine torque c) Vehicle speedQuestion 5: What enables the all-wheel drive clutch to transfer over 50% of drive power to the front axle?a) The front axle lead b) The fact that the front axle can transmit up to 550 Nm of torque. c) The special coating of the plate lining26 BackForward Ξ ContentsQuestion 6: What is the main advantage (apart from traction) of distributing over 50 % of drive power to the front axle?a) The rear tyres are conserved. b) The longitudinal force acting on the rear wheels is reduced allowing more lateral force to be transmitted. The increases driving stability when needed. c) The load on the 7-speed dual clutch gearbox is reduced.Question 7: What are the tasks of the mechanical powered oil pump in the front final drive?a) It produces the system pressure for the all-wheel drive clutch. b) It is responsible for cooling the front axle differential. c) It is repsonsible for cooling the all-wheel drive clutch and for filling the sump for Haldex clutch pump V181.Question 8: Which control variable is used to regulate the hydraulic pressure for the all-wheel drive clutcha) The speed of the pump motor of Haldex clutch pump V181. b) The control current of the valve for controlling the degree of opening of clutch N373 c) The discharge pressure of the pressure relief valveQuestion 9: At which mileage (km) or after which time in service is it necessary to change the Haldex oil?a) 60,000 km b) 3 years c) 180,000 kmQuestion 10: What is there to do after changing the Haldex oil? a) Reprogram the all-wheel drive clutch. b) Reset the programmed values for oil deterioration stored in the all-wheel drive control unit. c) Reset the offset of the hydraulic pressure sensor G492 stored in the all-wheel drive control unit.Solutions: 271) b; 2) c; 3) a; 4) c; 5) a; 6) b; 7) c; 8) a; 9) c; 10) b All rights reserved. Technical specifications are subject to change. Copyright AUDI AG I/VK-35 service.training@audi.de AUDI AG D-85045 Ingolstadt Technical revision status 06/15 Printed in Germany A15.5S01.27.20642Audi Vorsprung durch Technik