TECHNICAL DOCUMENTATION

SSP 644 Audi A4 (type 8W)

PDFEN100 pages22 MB
SSP 644 Audi A4 (type 8W) - PDF cover

This PDF is currently unavailable.

Read document text
Self Study Programme 644 For internal use onlyAudi A4(type 8W)Audi Service Training BackThe A4 family and its predecessor the Audi 80 have been technological innovators and true winners for many decades. The brand with the four rings already set new standards for lightweight construction, performance and agility with the first Audi 80 in the year 1972. The brand’s longstanding bestsellers have always played a major role at Audi. The new Audi A4 saloon and the new Audi A4 Avant (type 8W) feature numerous high-end technologies which set higher benchmarks for their class. They combine elegant design with an innovative operating concept, systematic lightweight construction and new, efficient drivetrain solutions. The Audi A4 saloon and Audi A4 Avant are also ahead of their peers in terms of infotainment and assistance systems. As a result, Audi drivers can look forward to a truly high-tech experience ― an innovative synthesis of technology and aesthetics. When it comes to aerodynamics, the two new models dramatically outpace the competition. The Audi A4 saloon has a drag coefficient of 0.23, while the Avant achieves 0.26. The rear design plays a pivotal role in terms of aerodynamics. On the new Audi A4 saloon, the lines of the rear hatch ensure that the air flow is smooth.Forward Ξ ContentsOn the Audi A4 Avant, a roof edge spoiler with a strong downward slant performs this function. When it comes to interior dimensions, the new Audi A4 saloon and the Audi A4 Avant surpass their predecessors in almost every respect. All seats offer a feeling of genuine spaciousness. The interior design underscores this impression, as its clear architecture is strictly focused on horizontal lines. With the anatomically shaped front seats, the head restraints can be adjusted not only for height, but also for distance from the head. At market launch in Europe, the Audi A4 saoloon and the A4 saloon will be available with a choice of three TFSI and four TDI engines. All engines comply with the Euro 6 emission limits, so that the TDI has been labeled a clean diesel. Manual gearboxes, S tronic and tiptronic, front-wheel drive and quattro drive – there are various solutions for power transmission in the new A4 models Tailored technology is available for each engine.644_002Learning objectives of this self study programme: This self study programme describes the design and functioning of the Audi A4 (type 8W). Once you have completed this self study programme you will be able to answer questions on the following topics: • • • • • • • New features of the body New features of the occupant protection system Engines and fuel tank systems New power transmission features New chassis features Function of the surround camera New features of the air conditioning system2 ContentsIntroductionPresentation __________________________________________________________________________________________________________________________________________________ 4 Dimensions ___________________________________________________________________________________________________________________________________________________ 6BodyIntroduction __________________________________________________________________________________________________________________________________________________ 8 Body structure ________________________________________________________________________________________________________________________________________________ 8 Attachments _________________________________________________________________________________________________________________________________________________ 12 Seating systems _____________________________________________________________________________________________________________________________________________ 14Occupant protectionPassive safety ________________________________________________________________________________________________________________________________________________ 16 Active safety _________________________________________________________________________________________________________________________________________________ 23EnginesPetrol engines _______________________________________________________________________________________________________________________________________________ 24 Diesel engines _______________________________________________________________________________________________________________________________________________ 26 Fuel tank _____________________________________________________________________________________________________________________________________________________ 28 SCR system __________________________________________________________________________________________________________________________________________________ 32 Engine/gearbox combinations _____________________________________________________________________________________________________________________________ 33Power transmissionOverview _____________________________________________________________________________________________________________________________________________________ 34 6-speed manual gearbox 0DJ/0CS _ _______________________________________________________________________________________________________________________ 36 7-speed dual clutch gearbox 0CK/0CL – S tronic _ ________________________________________________________________________________________________________ 44 park-by-wire (PBW) parking lock __________________________________________________________________________________________________________________________ 48 8-speed automatic gearbox 0D5 – tiptronic ______________________________________________________________________________________________________________ 58 Gearbox functions _ __________________________________________________________________________________________________________________________________________ 60ChassisOverall concept ______________________________________________________________________________________________________________________________________________ 64 Axles and wheel alignment ________________________________________________________________________________________________________________________________ 65 Standard/sports suspension with electronic damper control (1BL/1BQ) _____________________________________________________________________________ 68 Brake system ________________________________________________________________________________________________________________________________________________ 71 Steering system _____________________________________________________________________________________________________________________________________________ 75 Adaptive Cruise Control (ACC) _____________________________________________________________________________________________________________________________ 79 Wheels and tyres ____________________________________________________________________________________________________________________________________________ 80Electrical systemInstallation locations of control units ____________________________________________________________________________________________________________________ 82 Topology _____________________________________________________________________________________________________________________________________________________ 84 Surround cameras _ __________________________________________________________________________________________________________________________________________ 86InfotainmentOverview of versions ________________________________________________________________________________________________________________________________________ 92Air conditioningIntroduction _________________________________________________________________________________________________________________________________________________ 94 Air conditioners _____________________________________________________________________________________________________________________________________________ 95 Auxiliary heating ____________________________________________________________________________________________________________________________________________ 96 Steering wheel heating _____________________________________________________________________________________________________________________________________ 96ServiceInspection and maintenance _ ______________________________________________________________________________________________________________________________ 97 Self study programmes _ ____________________________________________________________________________________________________________________________________ 99The self study programme teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a repair manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. This content is not updated. For further information about maintenance and repair work, always refer to the current technical literature.NoteReference3 BackForward Ξ ContentsIntroductionPresentationThe new-generation Audi A4 is a fascinating synthesis of technology and aesthetics. All the technology in the brand's bestselling family has been redeveloped so that it yet again defines the benchmark in the segment.Engines• 1.4l R4 TFSI engine (110 kW) • 2.0l R4 TFSI engine (140 – 185 kW) • 2.0l R4 TDI engine (90 – 140 kW) • 3.0l V6 TDI (160 – 200 kW) Other engine versions will become available at a later date.HeadlightsDepending on trim level, the A4 can be equipped with either xenon plus, LED or matrix LED headlight technology. The dynamic turn signals use a series of light diodes switched sequentially from inside to outside in the direction of turn, clearly signaling the car’s direction to other road users.Assistance systemsThe following systems are optionally available: • adaptive cruise control Stop&Go including traffic jam assist • Predictive efficiency assist • Audi active lane assist • Audi side assist • Park assist • Rear cross traffic assist • Exit warning • Turning assist • Evasion assist • Camera based traffic sign recognition • Audi pre sense city, basic and rearAir conditioningSingle-zone automatic air conditioning is standard. Just a few buttons and dials are sufficient for convenient control. Audi also offers the option of a 3-zone automatic air conditioning system whose temperature displays are integrated into the rotary dials. When one of the capacitive rocker switches is approached by a finger, its function is shown enlarged on the dark LCD display and selected.4 BackForward Ξ ContentsDisplays and operationDisplays appear on a central MMI monitor which is permanently attached to the instrument panel. The focal point of the operating system is the MMI allin-touch control unit with a full touch surface. Depending on trim level, the Audi Q7 features a fully digital instrument cluster - the Audi virtual cockpit. A head-up display is optional. The system projects relevant information onto the windscreen in the form of easily comprehensible symbols and characters.BodyIn the Audi A4 saloon and A4 Avant, hot-stamped components form the high-strength, crash-proof backbone of the occupant cell. They strengthen the transition from the front end to the cabin, the frontal area of the roof frame, the B posts, the side sills and parts of the floorpan. The module cross member under the instrument panel is made of extruded and sheet aluminium, while the front cross member is an extruded profile. In addition, the nodes in the upper ends of the D posts are made of die-cast aluminium and the rear hatch is also aluminium. A sensor control for opening the luggage compartment, an electrical luggage compartment cover and an electric drive for the rear hatch are available for the A4 Avant.644_036Power transmissionA newly developed eight-speed tiptronic transfers the engine's power to the quattro full-time all-wheel drive system. Thare is also a 6-speed manual gearbox or a 7-speed S tronic dual clutch gearbox with the option of frontwheel drive or quattro. The sport differential, optional as of 2016, optimises handling.SuspensionThe chassis is characterised by precise electro-mechanical steering in addition to the newly developed five-link front and rear axles. An additional advantage is that driving dynamics can be adjusted to each situation. Audi drive select influences the mapping of the power steering and accelerator pedal as well as the optional variable suspension. A central suspension control system has been applied to achieve ideal interaction between the various driving dynamics systems.5 BackForward Ξ ContentsDimensions14279851572 1842644_0471555 2022644_048911039538802820 47261026644_0496684 BackForward Ξ Contents14762)14213)14462)13843)1081/10504) 1000644_050Exterior dimensions and weightsLength in mm Width (not including exterior mirrors) in mm Width (including exterior mirrors) in mm Height in mm Front track width in mm Rear track width in mm Wheelbase in mm Kerb weight in kg Gross vehicle weight in kg 4726 1842 2022 1427/14344) 1572 1555 2820 1430 2030Inner dimensions and other specificationsFront cabin width in mm Front shoulder width in mm Rear cabin width in mm Rear shoulder width in mm Load sill height in mm Boot capacity in l Drag coefficient cw Capacity of fuel tank in l 14762) 14213) 14662) 13843) 684/6344) 480/5054) 0.23/0.264) 40/54/585)Maximum headroom Elbow room width 3) Shoulder room width 4) Dimension for Audi A4 Avant 5) Front wheel drive / front wheel drive (optional) / quattro drive1) 2)All dimensions are given in millimetres and refer to the unladen weight of the vehicle.7 BackForward Ξ ContentsBodyIntroductionThe Audi A4 saloon and the Audi A4 Avant bodies have a hybrid design. This lightweight construction concept utilises die-cast aluminium components in addition to regular sheet-metal parts. A decisive factor in modern body construction is the lightness and rigidty of the body structure as a whole. For this reason, the bodies of the Audi A4 incorporate die-cast aluminium components in addition to soft, high-strength, modern high-strength and ultra-highstrength sheet-steel components (2 in the saloon and 4 in the Avant). These are the front spring strut mounts and the nodes at the upper end of the D posts on the Audi Avant A4. Thanks to geometrical lightweight construction and an intelligent material mix, the body of the Audi A4 is 15 kg lighter than that of the Audi A4 (type 8K).Body structureUltra-high-strength hot-stamped components are used in the following areas: • • • • • • • • Front frame side member Front side member reinforcement Bulkhead (tunnel bridge) A post B post Inner chassis rail (sill) Upper tunnel reinforcement Rear frame side memberKey:Die-cast aluminium Aluminium profile Ultra-high-strength steel (hot-stamped) Advanced high-strength steel High-strength steel Soft steel8 BackForward Ξ ContentsUltra-high-strength steel (hot-stamped)In the Audi A4 saloon and in the Audi A4 Avant, hot-stamped components form the high-strength, crash-proof backbone of the occupant cell. They strengthen the transition from the front end to the cabin, the frontal area of the roof frame (A post), the B posts, the lower beams and parts of the floorpan. They constitute 17 % of the body structure. Special care must be taken when handling hot-stamped steel during servicing. This material must not be straightened or reshaped, even if the deformation is only minimal, due to its high yield strength and rebound effect. For this reason, attention was given to special service solutions during the development of the body structure. This means that damaged components are replaced fully or partially in specially designated parting cut areas (depending on energy flow).Sectional repairs may be performed on the following heat-stamped components: • A post • B postAll other hot-stamped components must, if damaged, be completely replaced to manufacturer specifications. This is because high heat input into the welding area would irreversibly compromise the strength and structure of the component by causing microstructural changes in the material.644_152644_1539 BackForward Ξ ContentsOuter skinBoth Audi A4 models have a steel outer skin. The attachments are also made of steel. Only the impact absorbers and the rear hatch of the Audi A4 are made of aluminium. The hatch is deep-drawn in the press using what is known as an "intelligent" tool. Laser sensors measure how the sheet metal behaves during the shaping process. If necessary, electrically operated drawing aids make small adjustments to the press. This results in even higher precision in the magnitude of thousandths of a millimetre.Outer skin of the A4 saloonSheet aluminium Die-cast aluminium Aluminium profile Ultra-high-strength steel (hot-stamped) Advanced high-strength steel High-strength steel Soft steel644_154Outer skin of the Audi A4 AvantSheet aluminium Die-cast aluminium Aluminium profile Ultra-high-strength steel (hot-stamped) Advanced high-strength steel High-strength steel Soft steel644_155 10 BackForward Ξ ContentsAluminium castingsThe aluminium castings in the vehicle structure are joined to the adjacent sheet-metal parts by punch riveting and using structural adhesive. The adhesive also serves to insulate both materials from one another, thus preventing contact corrosion. Specific repair solutions have been developed for repairing damage to these aluminium castings and adjoining sheet-steel parts. Straightening and reshaping work is not permitted in the area of these components.Structural integration of the spring strut mounts in the Audi A4 saloon and Audi A4 Avant The front spring strut mounts are highly integrated die-cast aluminium components. Compared with sheet-steel components, which are welded together out of several parts, they reduce weight in the Audi A4 by a total of 8 kg. This design allows a very stiff connection between the upper wishbones and the car body, thus ensuring optimal conditions for driving dynamics.Side member, wheel arch upper end (wing stay)644_156Spring strut mountStructural integration of the upper D post node on the Audi A4 Avant There are two die-cast aluminium nodes in the upper D posts on the Audi A4 Avant. The component incorporates the hinge mounts for the rear hatch attachment and the roof rail mount.Rear roof frame644_157Node, D post upper end11 BackForward Ξ ContentsAttachmentsStriker on the bootIf the Audi A4 (type 8W) is equipped with an active pedestrian protection system, the bonnet is displaced upwards and backwards when a collision with a pedestrian is detected. To facilitate this type of displacement, long strikers which allow longitudinal movement within the catch hooks are fitted in the other Audi models. In certain markets, "movable" strikers are used on the Audi A4 (type 8W). The maximum displacement is approximately 50 mm.Initial positionPosition when bonnet is deployed644_109644_110Note Refer to the current service literature for information on replacement of the strikers after deployment of the pedestrian protection system.Door handlesThe kinematics of the door handles on the Audi A4 (type 8W) have been modified. Whereas door handles typically move in a horizontal direction only, this door handle now also swivels approximately 30° upwards. This results in an intuitive action which is anatomically adapted to the movement of the hand and provides better ergonomics when opening the door.644_106644_10712 BackForward Ξ ContentsActive radiator louvreDepending on engine type, the Audi A4 (type 8W) may be equipped with an active cooling air intake system which improves aerodynamics and assists the thermal management system. Unlike the Audi Q7 (type 4M), the A4 features a split active cooling air intake system. The upper and lower louvres can be activated separately. Three positions are possible depending on various input variables such as coolant temperature, engine temperature, gearbox temperature and exhaust gas temperature. • Both units closed • The lower unit open and the upper unit closed (to ensure earlier air flow through the charge air cooler). • Both units open The lower louvre does not have a bottom plate. This ensures a continuous, forced flow of air through the charge air cooler. Both units are open upwards of a speed of 160 kph.Upper radiator louvreLower radiator louvre644_111Roof variantsSliding sunroofs are optional for the A4 saloon and the A4 Avant. The sunroof option for the saloon is a regular sliding sunroof with a moving glass panel. The A4 Avant has a two-section panoramic glass sunroof where the rear panel is fixed and the front panel is movable.SaloonAvant644_104644_10513 BackForward Ξ ContentsSeating systemsThe Audi A4 and A4 Avant have front seats tailored to the contours of the body. The head restraints are adjustable for height and distance to the back of the head. The standard seats are optionally available with heating and partial or full electrical adjustment. A central armrest in the front – adjustable if desired and with a large storage space – large door pockets and two cup holders are standard features, providing enhanced seating comfort.Standard front seatHead restraints with manual adjustment for height, angle and distanceOptional electrical lumbar supportFront seat subframe of high-strength steel Optional electric seat adjustment644_009Sport seatThe optional sport seats have electrically adjustable lumbar supports and are optionally available with seat ventilation.Seat vent V388/V389Seat vent V390/V391 Operating unit for driver seat adjustment E470 Seat control units J136/J521644_010 14 BackForward Ξ ContentsSeat memoryThe memory function allows personal seating profiles to be stored for the driver and recalled. The memory function can be operated with the remote control key and with the recall buttons in the driver's door. Whenever the vehicle is locked, the driver's seat profile is re-stored and assigned to the remote control key. The seat profile is automatically recalled when the door is opened. The settings for the seats and the two door mirrors can be stored as indicated in the adjacent table. Remote control key Driver Seat Both door mirrors x x Recall button Driver x xSystem overview and signal characteristic The information from the operating units for the driver/front passenger seat with memory function E97/E277 is processed by the two driver/front passenger door control units J386/J387. This information is transferred to the two seat control units with memory function J136/J521 via the convenience CAN. The seat control units then activate the corresponding control motors.Convenience CAN644_027Key: E97 Operating unit for driver seat adjustment with memory function E277 Operating unit for front passenger seat adjustment with memory function J136 Seat and steering column adjustment control unit with memory function J386 Driver's side door control unit J387 Door control unit, pass. side J519 Electrical system control unit J521 Front passenger seat adjustment control unit with memory V243 V244 V245 V246 V256 V257 Driver seat angle adjustment motor Front passenger seat angle adjustment motor Driver seat height adjustment motor Front passenger seat height adjustment motor Driver seat depth adjustment motor Front passenger seat depth adjustment motorTSVL Front left seat coupling TSVR Front right seat coupling15 BackForward Ξ ContentsOccupant protectionPassive safetyOn the following pages you will find a summary of the occupant protection system in the Audi A4.In-car airbagsDriver airbag Front pass. airbagDriver side knee airbagComponentsDepending on country version and trim level, the passive occupant and pedestrian protection system in the Audi A4 can comprise the following components and systems: • Airbag control unit • Adaptive driver airbag • Adaptive front passenger airbag (front passenger airbag, two-stage country version) • Front side airbags • Rear side airbags (equipment option) • Head airbags • Knee airbags (country version) • Front airbag crash sensors • Crash sensors for side impact detection in the doors • Crash sensors for side impact detection in the C posts • Centre pedestrian protection crash sensor (acceleration sensor, country version) • Left and right pedestrian protection crash sensors (pressure sensors, country version) • • • • Front side airbag• • • • • • • Front inertia-reel seat belts with pyrotechnic belt tensioners Front inertia-reel seat belts with electrical belt tensioners Front inertia-reel seat belts with active belt force limiters Inertia-reel seat belts for second seat row with pyrotechnic belt tensioners, driver and front passenger sides (country or trim level version) Seat belt warning for all seats (country version) Seat occupancy sensor in front passenger seat Front pass. airbag disabling switch (country version or trim level version) Front pass. airbag OFF and ON warning lamp (country version or trim level version) Driver and front passenger seat position sensors Pedestrian protection trigger (country version) Battery isolator16 BackForward Ξ ContentsPass. side knee airbagFront side airbagHead airbag, driver and front pass. sideRear side airbagRear side airbag644_115Note The schematic diagrams in the chapter "Occupant protection" provide a better understanding.17 BackForward Ξ ContentsSystem overviewThe system overview shows the components for all markets. Keep in mind that this constellation is not possible in a production model.644_003 18 BackForward Ξ ContentsAdditional equipmentEquipment specifications may vary due to the different requirements and statutory provisions which apply to vehicle manufacturers in the various markets.Key to figure on page 18: E24 E25 E224 F390 F391 F392 G128 G179 G180 G256 G257 G283 G284 G551 G552 G553 G554 G598 G599 G693 G851 G852 J234 J285 J533 J706 J854 J855 Driver side seat belt switch Front pass. side seat belt switch Airbag disabling switch, pass. side Driver side seat belt switch, 2nd seat row Centre belt switch, 2nd seat row Front pass. side seat belt switch, 2nd seat row Pass. side seat occupancy sensor Side airbag crash sensor, driver side Side airbag crash sensor, pass. side Rear side airbag crash sensor, driver side Rear side airbag crash sensor, pass. side Front airbag crash sensor, driver side Front airbag crash sensor, pass. side Belt force limiter, driver side Belt force limiter, pass. side Seat position sensor, driver side Seat position sensor, pass. side Pedestrian protection actuator 1 Pedestrian protection actuator 2 Centre pedestrian protection crash sensor Driver side crash sensor for pedestrian impact mitigation 2 Pass. side crash sensor for pedestrian impact mitigation 2 Airbag control unit Control unit in dash panel insert Data bus diagnostic interface (gateway) Seat occupancy recognition control unit Front left seat belt tensioner control unit Front right seat belt tensioner control unit K19 Seat belt reminder warning lamp K75 Airbag warning lamp K145 Front pass. airbag OFF warning lamp (ON and OFF status of front pass. airbag is indicated) N95 Driver side airbag igniter N131 Front pass. side airbag igniter 1 N132 Front pass. side airbag igniter 2 N153 Seat belt tensioner igniter 1, driver side N154 Seat belt tensioner igniter 1, pass. side N196 Rear seat belt tensioner igniter, driver side N197 Rear seat belt tensioner igniter, pass. side N199 Side airbag igniter, driver side N200 Side airbag igniter, pass. side N201 Rear side airbag igniter, driver side N202 Rear side airbag igniter, pass. side N251 Head airbag igniter, driver side N252 Head airbag igniter, pass. side N253 Battery isolation igniter N295 Knee airbag igniter, driver side N296 Knee airbag igniter, pass. side N490 Driver airbag relief valve igniter N491 Front pass. airbag relief valve igniter T16 16-pin connector, diagnostic portWire colours: Diagnostics CAN Infotainment CAN FlexRay Input signal Output signal19 BackForward Ξ ContentsSensors Seat occupancy sensorDue to the different statutory requirements applicable in the marketplace, two different versions of the seat occupancy sensor are used in the Audi A4.Version 1 für ROW1) vehicles Passenger side seat occupancy sensor G128 The Audi TT (type FV) uses a new-generation passenger side seat occupancy sensor G128. This new-generation seat occupancy sensor is also installed on the Audi A4. The seat occupancy sensor offers the following benefits for customers and service: • Low parts diversity • Easy installation and removal, no need to remove seat upholstery • Minimal labour time during replacement • Minimal repair cost during replacement • No influence on seat ventilation (optional equipment)Installation location The seat occupancy sensor is attached to the seat assembly at the bottom of the wire frame by clips. The seat upholstery and seat cover are located overhead. When a person sits on the seat, the seat upholstery is pushed downwards by weight force thereby activating the seat occupancy sensor. When the person occupying the seat stands up, the seat upholstery rebounds upwards,thus relieving the load on, and thus deactivating, the seat occupancy sensor.644_004Pass. side seat occupancy sensor G128Function The seat occupancy sensor is used for the purpose of detecting an occupant on the front passenger seat. The seat occupancy sensor has a resistance of approximately 400 ohms in the non-activated state. This value means that no-one is occupying the seat. If a person is occupying the seat, the seat occupancy sensor is activated and its resistance changes to approximately 100 ohms. The resistance values tell the airbag control unit if the front passenger seat is occupied or vacant. If the airbag control unit J234 recognises an occupied seat and the latch plate of the inertia-reel seatbelt is not engaged in the seat belt buckle, the airbag control unit J234 activates the audible and visual seat belt reminders.kg400 Ω644_0051)100 Ω644_006ROW = rest of world20 BackVersion 2 für NAR1) vehicles Pass. side seat occupancy sensor G128 with seat occupancy recognition control unit J706 Until now, the capacitive systems which were first offered in the Audi A7 Sportback (type 4G) used a separate sensor mat (pass. side seat occupancy sensor G128) to determine if a front passenger seat is occupied or vacant. The Audi TT (type FV) uses a new-generation passenger side seat occupancy sensor G128 in NAR1) models. In this new-generation system, the seat heater element (front passenger seat heater Z8) serves not only as a seat heater but also as a sensor mat for seat occupancy recognition. As before, capacitive sensors are used for occupancy recognition. For the sake of simplicity, the following text refers solely to the passenger side seat occupancy sensor G128, although the sensor mat also serves as the front passenger seat heater Z8 as described above.Forward Ξ ContentsThe seat occupancy recognition control unit J706 is connected to ground (the seat assembly) by a discrete wire. To prevent interference with the capacitive system, the wires leading to the passenger side seat occupancy sensor G128 are shielded. The seat occupancy recognition control unit J706 is connected to the airbag control unit J234 by means of a LIN bus.644_012Service KitIn the Service Kit, the seat occupancy recognition control unit J706 and the passenger side seat occupancy sensor G128 are calibrated to one another. This is why a new Service Kit must be installed in the event of a fault in the control unit or in the seat occupancy sensor. It is not permitted to interchange individual components.Pass. side seat occupancy sensor G128644_013The electrical plug connection between the seat occupancy recognition control unit J706 and the passenger side seat occupancy sensor must not be disconnected. Depending on vehicle trim level, the Service Kit may comprise the following components:Service Kit version 1 • Seat occupancy recognition control unit J706 • Seat cushion • Passenger side seat occupancy sensor G128 including wiring kit. In this case, the passenger side seat occupancy sensor is bonded to the seat upholstery.Service Kit version 2 • Seat occupancy recognition control unit J706 • Seat upholstery • Passenger side seat occupancy sensor G128 including wiring kit. In this case, the passenger side seat occupancy sensor is stitched to the seat upholstery.Vehicles without seat heating use the same passenger side seat occupancy sensor G128 as vehicles with seat heating.DiagnosticsThe passenger side seat occupancy sensor G128 and the seat occupancy recognition control unit J706 are diagnosed via the airbag control unit J234. If a Service Kit is replaced, a basic setting procedure must be performed using the Guided Fault Finding function. In this case, the serial number of the Service Kit is transferred to the airbag control unit J234.1)NAR = North American Region21 BackForward Ξ ContentsAirbag control unit J234The airbag control unit J234 of the Audi A4 is based on the same control unit generation used in the Audi Q7 (type 4M). The system designation of the airbag control unit is "Airbag10.44" and can be recalled in the Guided Fault Finding under "Control unit identification". The features and the setup of the airbag control unit J234 have been adapted to suit the Audi A4. For details of the equipment specification, refer to the system overview on page 18.644_103Airbag control unit J234Sensors As previously in the Audi Q7 (type 4M), the driving dynamics control sensors are integrated in the airbag control unit in the Audi A4. The driving dynamics control sensors measure acceleration in the X and Y directions as well as the yaw rate about the Z axis. The driving dynamics control sensors work in a lower acceleration and deceleration range than the crash sensors. This acceleration and deceleration levels which can occur during a collision are clearly different to those which can occur when a vehicle loses grip (e.g. oversteer, understeer). The crash sensors for the X and Y directions have the ability to measure acceleration rates of up to approximately +/- 96 g, while the driving dynamics control sensors have the ability to measure acceleration rates of up to approximately +/- 5 g, where 1 g is the force of gravity or approximately 9.81 m/s2. The yaw rate sensors have the ability to measure rates of up to approximately +/- 187°/s (degrees per second). If the vehicle is equipped with dynamic steering (PR No. 1N8) or the quattro sport differential (PR No. GH2), the driving dynamics control sensors are duplicated in the airbag control unit J234. This provides redundant (multiple) backup for the sensor signals for dynamic steering and quattro Sport.Reference More detailed information about the subsystems mentioned herein can be found in the following self study programmes: • The dynamic steering system: Self Study Programme 402 "Dynamic steering in the Audi A4 ’08". • The quattro sport differential: Self Study Programme 476 "Rear final drive 0BF/0BE - sport differential". • The airbag control unit: Self Study Programme 637 "Audi Q7 (type 4M) Occupant protection and infotainment".22 BackForward Ξ ContentsActive safetyAudi pre senseThe Audi pre sense system (pre sense city, pre sense basic, pre sense rear, pre sense front, evasion assist or turn assist) of the Audi A4 has the same on-board pre sense functions as the Audi Q7 (type 4M). Of course, the components and the specifications have been adapted to suit the A4 (type 8W). In functional terms, the Audi pre sense functions in the A4 are identical to those in the Audi Q7.Display in instrument clusterPre sense city with pedestrian recognition functionAudi pre sense644_030644_031Turning assist644_032Evasion assist644_033Reference For detailed information about Audi pre sense, refer to Self Study Programme 637 "Audi Q7 (type 4M) Occupant Protection and Infotainment".23 BackForward Ξ ContentsEnginesPetrol enginesTorque/power curve of 1.4l TFSI engineEngine with code CVNA   Power output in kW   Torque in NmEngine speed [rpm]644_015Features Engine code Type Displacement in cm3 Stroke in mm Bore in mm Number of valves per cylinder Firing order Compression ratio Power output in kW at rpm Torque in Nm at rpm Fuel type Engine management system Lambda/knock control Mixture formation Exhaust gas treatment Emission standard CO2 emissions in g/kmSpecifications CVNA 4-cylinder inline engine 1395 80.0 74.5 4 1-3-4-2 10,5 : 1 110 at 1500 - 3500 250 at 5000 - 6000 Premium unleaded 95 RON Bosch MED 17.01.61 Adaptive lambda control, adaptive knock control Sequential direct injection Oxidising catalyst, oxygen sensors (2 bistable sensors) EU 6 (W) 1141)1)Audi A4 saloon with front wheel drive and S tronic24 BackForward Ξ ContentsTorque/power curve of 2.0l TFSI engineEngine with code CVKB   Power output in kW   Torque in Nm Engine with code CYRB   Power output in kW   Torque in NmEngine speed [rpm]644_016Features Engine code Type Displacement in cm3 Stroke in mm Bore in mm Number of valves per cylinder Firing order Compression ratio Power output in kW at rpm Torque in Nm at rpm Fuel type Engine management system Lambda/knock control Mixture formation Exhaust gas treatment Emission standard CO2 emissions in g/kmSpecifications CVKB 4-cylinder inline engine 1984 92.8 82.5 4 1-3-4-2 11.65 : 1 140 at 4200 - 6000 320 at 1400 - 3700 Premium unleaded 95 RON Bosch MED 17.01.10 CYRB 4-cylinder inline engine 1984 92.8 82.5 4 1-3-4-2 9.6 : 1 185 at 5000 - 6000 370 at 1600 - 4500 Premium unleaded 95 RON SIMOS 18.4Adaptive lambda control, adaptive knock control Combined (dual) direct (FSI) and multipoint (MPI) injection with adaptive idle charge compensation Close-coupled ceramic calatyst, oxygen sensors before and after catalytic converter EU 6 (W) 1141) EU 6 (W) 1292) / 1393)Audi A4 Avant with front wheel drive and S tronic Audi A4 saloon with front wheel drive and S tronic 3) Audi A4 Avant with quattro drive and S tronic1) 2)25 BackForward Ξ ContentsDiesel enginesTorque/power curve of 2.0l TDI engineEngine with code DEUC   Power output in kW   Torque in Nm Engine with code DEUB   Power output in kW   Torque in Nm Engine with code DEUA   Power output in kW   Torque in Nm Engine with code DETA   Power output in kW   Torque in NmEngine speed [rpm]644_017Engine speed [rpm]644_018Features Engine code Type Displacement in cm Stroke in mm Bore in mm Number of valves per cylinder Compression ratio Power output in kW at rpm Torque in Nm at rpm Engine management system Maximum injection pressure in bar Exhaust gas treatment Emission standard CO2 emissions in g/km3Specifications DEUC DEUB DEUA DETA4-cylinder inline engine 1968 95.5 81.0 4 16.2 : 1 90 at 3500 – 4000 270 at 1500 - 3000 Bosch EDC 17 2000 with solenoid injectors, 8-hole nozzles Oxidising catalyst, SCR coated diesel particulate filter, oxygen sensors EU 6 (W) –1) EU 6 (W) –1) EU 6 (W) 992) / 1043) EU 6 (W) 1072) / 1093) 1968 95.5 81.0 4 16.2 : 1 100 at 3000 - 4400 320 at 1500 - 3000 1968 95.5 81.0 4 16.2 : 1 110 at 3250 - 4200 320 at 1500 - 3250 1968 95.5 81.0 4 15.5 : 1 140 at 3800 - 4200 400 at 1750 - 3000Reference For further information about the diesel engines of the Modular Diesel Platform, please refer to Self Study Programme 608 "Audi 1.6l / 2.0l 4-cylinder TDI engines".26 BackForward Ξ ContentsTorque/power curve of 3.0l TDI engineEngine with code CSWB   Power output in kW   Torque in Nm Engine with code CRTC   Power output in kW   Torque in NmEngine speed [rpm]644_019Engine speed [rpm]644_020Features Engine code Type Displacement in cm Stroke in mm Bore in mm Number of valves per cylinder Compression ratio Power output in kW at rpm Torque in Nm at rpm Engine management system Maximum injection pressure in bar Exhaust gas treatment Emission standard CO2 emissions in g/km3Specifications CSWB V6-cylinder engine 2967 91.4 83.0 4 16.0 : 1 160 at 4000 – 5000 400 at 1250 - 3750 2967 91.4 83.0 4 16.0 : 1 200 at 3250 - 4250 600 at 1500 - 3000 CRTCBosch EDC 17 with start-stop and recuperation 2000 with piezo injectors Close-coupled NOx oxidising catalyst, SCR coated diesel particulate filter EU 6 (W) 110 EU 6 (W) 1292) / 1343)Data was unavailable at time of going to print. Audi A4 saloon 3) Audi A4 Avant1) 2)27 BackForward Ξ ContentsFuel tankThe fuel systems in the Audi A4 (type 8W) have the following features: • • • • • Compact design Maximum integration of components to reduce fuel emission No carrier plate Fuel delivery system with large integral swirl pot Use of sound-insulating baffles • The components in the secondary chamber, e.g. fuel level sender in quattro models, are not accessible to service personnel. There is only one service port in the fuel tank on the right. • A liquid trap with active extraction system is integrated in the fuel tank ventilation system. • Fluid separator at top of fuel tank filler neckDiesel-engined modelsThe figure shows the fuel tank of a vehicle with quattro drive without auxiliary heating.Fuel return lineFuel supply lineFuel vent valve644_040Fuel level sender, left pocketFuel delivery and sender unit Suction jet pump of active extraction systemFuel supply lineFuel delivery and sender unitSuction jet pumpBaffleFuel vent valveRollover valveBaffle28 BackForward Ξ ContentsVent lineRollover valveFilling volume Front wheel drive Front wheel drive (optional) quattro drive 40 litres 54 litres 58 litresFuel filler neckPetrol-engined modelsThe figure shows the fuel tank of a vehicle with front wheel drive and auxiliary heating.Vent line Fluid separatorActivated carbon canisterFuel filler neckMetering pump (for auxiliary heating) V54 Liquid trap with active extraction system644_039 29 BackForward Ξ ContentsTank ventilation systemDue to the space constraints in new models, the tank ventilation system has been revised. It was important to ensure that siphoning cannot occur in the line from the fuel filler neck to the activated carbon filter. The tank ventilation system is designed such that the fuel which enters the vent line can be actively extracted from the liquid trap while meeting the most stringent emission laws. The result is a higher tank capacity and less air in the tank moulding.Petrol-engined modelsFuel vent valveT pieceFuel pump (pre-supply pump) G6Vent line to activated carbon canisterOpen-ended drainage outletNon-return valveSuction jet pump of active extraction systemLiquid trap with active extraction systemKey: 30Fuel system pressure from fuel pump G6 Extraction Fuel return to tank moulding644_051 BackTank ventilation function The ventilation system is configured differently depending on what type of fuel is used. The system requires a larger liquid trap for models with petrol tanks due to the boiling characteristic of the fuel. The fuel which has collected in the liquid trap is extracted by means of a suction jet pump and drained off pressurelessly at the highest point in the tank.Forward Ξ ContentsEffects of failure of the tank ventilation system If one of the components of the ventilation system fails (lifetime configuration), problems may occur during refuelling (refuelling shut-off). A strong fuel odour could also be noticeable in petrolengined models (ACF canister flooding).Diesel-engined modelsOpen-ended drainage outletFuel pump (pre-supply pump) G6Vent line to fuel filler neckLiquid trap with active extraction systemFuel vent valveNon-return valveSuction jet pump of active extraction system644_08531 BackForward Ξ ContentsSCR systemThere are two different AdBlue® reducing agent capacity options for the SCR system: a reducing agent tank with a capacity of 12 litres and an optional tank for extended range with a capacity of 24 litres. The capacity of the 12 litre reducing agent tank can be differentiated by an extended filler tube and an extended vent line. A short filler and vent line indicates a capacity of 24 litres.Equalisation chamber The ventilation system within the reducing agent tank is designed such that the tank can be filled with AdBlue® reducing agent using pump nozzles. To be able to hold the reducing agent flowing into the tank at a high flow rate, there is an equalisation chamber in the vent line and in the filler neck. The returning reducing agent would otherwise cause the pump nozzle to shut off too early. To prevent the flow-back of reducing agent in the filler neck, a non-return flap is installed at the end of the filler neck.24 litre version12 litre versionReducing agent filler neck Equalisation chamber Extended vent line Extended filler line Vent line Filling line644_011Non-return flapReducing agent tank sender G684Swirlpot with reducing agent pump V437 Baffles Reducing agent tank heater Z102644_007Reducing agent quality sensor G849 (initially available in NAR version only) Outlet for draining the reducing agentReducing agent metering system control unit J880Swirlpot with reducing agent pump V437644_008Reference For more information about the SCR system, refer to Self Study Programme 632 "Audi Q7 (type 4M)".32 BackForward Ξ ContentsEngine/gearbox combinationsThe engine-gearbox combinations shown below are those currently available at market launch. Engines 1.4l TFSI engine (CVNA) 2.0l TFSI engine (CVKB, CYRB) 2.0l TDI engine (DEU..., DETA) 3.0l TDI engine (CSWB, CRTC)6-speed manual gearbox 0DJ ML322-6F6-speed manual gearbox 0CS ML402-6F7-speed dual clutch gearbox 0CK S tronic DL382-7F 7-speed dual clutch gearbox 0CL S tronic DL382-7Q 8-speed automatic gearbox 0D5 tiptronic AL552-8QRear final drive 0DB to 400 Nm 0D2 from 400 NmBreakdown of manufacturer codes: e.g.: ML322-6F A M D L Automatic planetary gearbox Manual gearbox Dual clutch gearbox Longitudinal mounting 6 F Q Number of gears Front-wheel drive quattro all-wheel drive (with integrated centre differential)322 Development number (provides information on torque capacity, generation and position of front final drive etc.)33 BackForward Ξ ContentsPower transmissionOverviewThe Audi A4 (type 8W) employs the same drivetrain concept as the preceding B8 series (type 8K, 8T, 8F). The automatic and manual gearboxes for front and all-wheel drive are new developments, which have been installed previously in a slight different configuration in the Audi A6 ultra (type 4G) and in the Audi Q7 (type 4M).7-speed dual clutch gearbox 0CLSplined prop shaftDepending on engine type, the following gearboxes will be available at start of production: • 6-speed manual gearbox 0DJ – ML322-6F – front wheel drive – refer to page 36 • 6-speed manual gearbox 0CS – ML402-6F – front wheel drive – refer to page 36 • 7-speed dual clutch gearbox 0CK – S tronic – DL382-7F – front wheel drive – refer to page 44 • 7-speed dual clutch gearbox 0CL – S tronic – DL382-7Q – allwheel drive – refer to page 44 • 8-speed automatic gearbox 0D5 – tiptronic – AL552-8Q – all-wheel drive – refer to page 58Assembly of the front prop shaftThe prop shaft is connected to the gearbox output shaft by a spline. For further information, refer to Self Study Programme 457 "Audi A8 ’10 Power Transmission" and the Audi Service TV programme "Audi A8 Power Transmission Part 2 / Topic: Splined Prop Shaft" of 02.09.2010.34 BackForward Ξ ContentsRear axle transmissionStandard • Rear final drive 0DB – for engines with max. torque of up to approx. 400 Nm – refer to Self Study Programme 632 "Audi Q7 (type 4M)", page 31 • Rear final drive 0D2 – for engines with max. torque of approx. 400 Nm or higher Sport differential 0D3 is an advancement on sport differential 0BF. The key modifications in sport differential 0D3 are: • • • • • Adaptation of the gearcase to the rear axle Welded crown wheel New axle oil and ATF Shortened sensors for more clearance to exhaust system The driving dynamics control system is integrated in the suspension control unit J775 (no longer in the all-wheel drive control unit J492). All that control unit J492 does is execute the commands issued by J775. • Various lightweight construction measures For further information about sport differential 0BF, refer to Audi Service TV programme "Audi quattro with sport differential", Parts 1, 2, 3 and 4 as well as Self Study Programme 476 "Rear final drive 0BF/0BE - sport differential".Optional • Rear final drive 0D3 – sport differential – to be used on Audi S4 for first time as of around Q2 2016Emergency-releasing the parking lock – refer to page 56Assembly of the rear prop shaftThe procedure for attaching the prop shaft to the rear axle drive is described in the bolting specification for triangular matching. Refer to Workshop Manual. For detailed information about triangular matching, refer to Self Study Programme 409 and the Audi Service TV programme "Audi A5 Power Transmission / Topic: Prop Shaft Assembly Concept" of 23.02.2010.Selector mechanism The automatic gearboxes are operated by means of shift-by-wire and park-by-wire technology – refer to page 40.644_058 35 BackForward Ξ Contents6-speed manual gearbox 0DJ/0CSThe Audi A4 (type 8W) features manual gearboxes which have been specially designed for low weight, making optimal use of installation space and improved efficiency. A key feature of these gearboxes is that they have no side shaft. In addition to being significantly lighter, the gearboxes are very narrow at the back. The slimline design reduces the width of the body tunnel, which in turn frees up space in the driver and front passenger footwells.Gearbox ventSelector shaftHydraulic connection and vent screw of clutch slave cylinder644_059Gearcase front end: • Made of magnesium in 0DJ gearbox • Made of aluminium in 0CS gearboxGearcase back – gearbox cover: • Made of magnesium in 0DJ and 0CS gearboxesA manual gearbox will be available at a later date for quattro all-wheel drive. It stems from the same gearbox series and will have the designation 6-speed manual gearbox 0CX.In models with the 0DJ / 0CS gearbox, maximum speed is reached in 5th and/or 6th gear, depending on engine type.Gear recognition sensor G604 • For information about G604, refer to Self Study Programme 486 "Audi A6 ’11", page 32 ff.644_060 36 Back6-speed manual gearbox 0DJ and 6-speed manual gearbox 0CS are identical in design and differ from one another principally in terms of the material used in manufacturing the front gearcase. The two gearcases for the 0DJ gearbox are made of magnesium. In the case of the 0CS gearbox, the front gearcase is made of aluminium and the rear gearcase (gearbox cover) is made of magnesium.Forward Ξ ContentsThe 0DJ gearbox with its two magnesium gearcases is lighter, while the 0CS gearbox has a higher torque capacity due to its aluminium front gearcase.Concentric clutch disengagement system Permanent magnet Oil panGear set of 0DJ / 0CS gearboxDifferential cage mounted in ball bearingsDrive pinionSpur gear stepDouble row angular contact ball bearings644_061The special oiling concept of the gear set allows for a low oil fill quantity. It also allows the vehicle to run at a much lower oil level, while significantly reducing churning and drag losses. To achieve this, the spur gear of the pinion shaft conveys the gear oil (ATF) into the oil drip pan, which in turn distributes it to the lubrication points. The oiling concept, a new low-viscosity MTF and friction-optimized gear set bearings provide much better efficiency and significantly reduce fuel consumption.Power is transmitted to the pinion shaft through a low-loss spur gear step. The short pinion shaft runs at right angles to the crown wheel, and there is no axial offset. This permits the use of lowfriction spiral teeth and low-viscosity MTF (gear oil) in the bevel gear. In addition, the final drive can be repaired by service centres in the conventional way. Double row angular contact ball bearings are used as fixed bearings in the pinion shaft, minimising prestress in the bearings and enabling the bearings to run smoothly.37 BackForward Ξ ContentsClutch moduleThe clutch modules are specially configured to meet the different requirements of the various engine versions. The 0DJ gearbox in combination with the 1.4l TFSI engine features a clutch module with a conventional dual-mass flywheel (DMF) and a non-self-adjusting clutch pressure plate. All other engine versions have self-adjusting clutch pressure plates and a DMF with a centrifugal pendulum-type absorber. The Audi Service TV programme "Dual mass flywheel with centrifugal pendulum absorber" of 16.01.2015 explains the functional principle of these dual-mass flywheels and provides practical advice for workshop personnel. The Audi Service TV programme "Audi A5 Power Transmission" of 23.02.2010 deals in depth with the clutch module.Dual mass flywheel with and without centrifugal pendulum-type absorber Clutch plate Transmission plate • Pay attention to correct order of assembly.There are three versions of the clutch pressure plate: • Non-self-adjusting clutch pressure plate • SAC clutch pressure plate (self-adjusting) • TAC clutch pressure plate (self-adjusting)The self-adjusting clutch pressure plates by LuK are currently available in two different versions - the SAC clutch pressure plate and the TAC clutch pressure plate.Ratchet mechanism of the TAC clutch pressure plateSAC clutch pressure plate SAC stands for "Self Adjusting Clutch". The SAC system is dependent on release force. In the SAC system, the clutch pressure plate can be reset after it has been adjusted to compensate for wear. Refer to Workshop Manual. This allows the clutch disc and the clutch pressure plate to be replaced individually. For more information about the SAC, refer to Self Study Programme 198 "The 2.7 l V6 biturbo".Threaded spindle Drive pawlPinion Anti-reversing lock644_062TAC clutch pressure plate TAC stands for "Travel Adjusting Clutch". The TAC system works by adjusting its release travel according to clutch wear. In the TAC system, the clutch pressure plate cannot be reset after it has been adjusted to compensate for wear. Refer to Workshop Manual. The clutch disc and clutch pressure plate may only be replaced together. The TAC clutch is used on models with higher torque engines because the TAC system is less susceptible to axial vibration.Function Travel is adjusted during the engagement and disengagement of the clutch. If the distance between the friction faces of the clutch pressure plate and the DMS decreases due to clutch wear, the release travel of the clutch changes accordingly. This change in travel activates a ratchet mechanism which is coupled with a threaded spindle and rotates the ramp ring, thereby compensating for wear. Further information about the TAC is available on the internet.38 BackForward Ξ ContentsClutch controlThe new gearbox series is equipped with a so-called CSC clutch release mechanism. CSC stands for "Concentric Slave Cylinder". The clutch slave cylinder and the release bearing form a functional unit and can only be replaced together.Advantages of the CSC clutch release mechanism: • Fewer moving parts and constant actuation forces over the lifetime of the clutch • Exact axial clutch release improves clutch release and engagement (enhanced comfort). • Minimum installation space requirementsClutch not actuated / clutch engagedRelease bearingClutch slave cylinderPreload springOil seal for gearbox input shaft644_063Clutch actuated / clutch disengagedKey: Clutch pressure Depressurised644_064Reference For detailed information about the function, design and service-related aspects of the 0CS gearbox in the Audi A6 ultra (type 4G), refer to the Audi Service TV programme "6-speed manual gearbox 0CS – front wheel drive / service information" of 14.03.2014.39 BackForward Ξ ContentsAutomatic gearbox selector mechanismThe Audi A4 (type 8W) employs the latest generation Audi selector mechanism with full shift-by-wire capability (SBW). This means that parking lock operation is also fully automatic. The term used for this is "park-by-wire" (PBW). There is no selector cable connecting the selector mechanism to the gearbox. This selector mechanism was previously used in the Audi Q7 (type 4M) and in the Audi R8 (type 4S) and will also be used in the future C series. The operating concept is highly intuitive and is essentially identical to the familiar operating logic of automatic gearbox models. After every operation, however, the selector lever always returns to the normal position of the automatic or tiptronic gate. The parking lock normally engages and disengages automatically via the Auto-P function, but can also be engaged manually by the driver using the P button.Basic shift schematic Possible positions of the selector lever. Normal position X in automatic mode or normal position T in tiptronic mode. Depending on the selector lever position, this position information (A1, A2 etc.) is displayed in the measured data of the diagnostic tester.644_065tiptronic gate Automatic gateShift schematic Positions selectable without moving the selector Selectable drive positions Normal position of the selector lever and current drive position Software lock: deactivate by pressing the release button E681 Software lock: deactivate by pressing the foot brake1) Mechanical locking by selector lever lock solenoid N110 – deactivate by pressing the release button E681644_066Note: An acknowledgement tone sounds when drive position R is engaged. Automatic gateA2 A1 X B1 B2 T+tiptronic gateXT T-644_068Speed-dependent gearbox protection function A change in driving direction from forwards to reverse and vice versa is only possible up to a driving speed of about 8 kph with the AL552 gearbox and up to about 15 kph with the DL-382 gearboxes. When this speed threshold is exceeded, a gearbox protection function prevents prevents direction reversal.644_0671) he orange-coloured software lock is activated in drive position N after about one second. This allows quick-changing of the drive position T from D to R and vice versa without applying the brake. The makes it possible, for example, to free a stuck vehicle by rocking it backwards and forwards and makes it easier to change gear when manoeuvring the vehicle.40 BackComponent overviewForward Ξ ContentsHandle for selector lever bottom section with selector lever gaiterHandle for selector lever upper sectionSelector lever release button E681P button – parking lock button E816 with parking lock warning light K320. K320 illuminates the P button in a dimmed fashion and is brightly lit when the parking lock is active.Selector lever position display Y5Plug connection E Selector leverPlug connection CSelector lever sensors control unit J587Selector mechanism (selector lever E313)Plug connection A644_069Selector lever release button E681 – release button Button E681 is used to deactivate the software lock, which is highlighted blue in Fig. 644_066, and to release selector lever lock N110. It consists of two shift elements for reliability and diagnostics. In the event of a fault, release button E681 is considered actuated. The locks marked red and blue (Fig. 644_066) are disabled. A fault is registered in the event memory and indicated in the instrument cluster. To move the selector out of drive positions P and N, the brake pedal must be pressed in addition to the release button.Parking lock button E816 – P button The P button is for manually deactivating the parking lock. The parking lock can only be activated if the vehicle is travelling at a speed of  x kph (AL552  3 kph, DL382  2 kph ( 1 kph with Auto-P function)). Button E816 comprises three shift elements for reliability and diagnostics. Its shift status is transferred to the selector lever sensors control unit J587 via two interfaces. In the event of a fault in E816, a message appears in the instrument cluster and the parking lock can only engaged by the Auto-P function.41 BackInformation exchange Data is exchanged between the selector mechanism and the gearbox through the gateway. The selector lever sensors control unit J587 communicates with the infotainment CAN, the gearbox control unit J217 and the FlexRay. In the event of a system malfunction in J587 after which the gearbox cannot be operated using the selector mechanism, drive positions P, R, N and D can be selected by simultaneously operating both shift paddles while the vehicle is stationary and with the brake applied. Information flowForward Ξ ContentsJ587 registers the positions of the selector lever as well as the signals from both buttons and sends this information on to the gearbox control unit. The gearbox control unit engages the gear corresponding to the driver input and sends this information on to J587. The selector lever control unit then activates the corresponding selector lever locks (N110/V577), the selector lever position display LEDs Y5 and the parking lock warning light K320. When a gear is selected, this information flow process involves a short delay until the corresponding gear symbol lights up.Special feature of the dual clutch gearboxes In the Audi A4 (type 8W) with dual clutch gearboxes of the DL382 series, J587 has two additional interfaces for controlling the parking lock holding magnets N486. Refer to function diagram and page 48 ff.Selector lever position display Y5Selector lever sensors control unit J587 with selector lever position sender G727 and transverse selector lever lock sender G868644_070Sender element for G868Sender element for G727Reference For further information about the selector mechanism, refer to Self Study Programme 643 "7-speed dual clutch gearbox 0BZ - S tronic in the Audi R8 (types 42 and 4S)".1)Note In the case of the 0D5 gearbox (AL552), the parking lock can only be disengaged (P-OFF) when the engine is running because the 0D5 gearbox uses a mechanical-powered ATF pump which only conveys ATF when the engine is running. In the case of the DL382 gearboxes, the engine does not have to be running to disengage the parking lock (P-OFF). That is because this gearbox is supplied with ATF by an electric-powered ATF pump and a pressure accumulator. This means that the supply of ATF is not dependent on engine operation and that the parking lock can be disengaged when the ignition is on.42 BackFunction diagram – selector mechanismForward Ξ ContentsKey: E313 Selector lever (selector mechanism) E681 Selector lever release button E816 Parking lock button G727 Selector lever position sender G868 Transverse selector lever lock sender J587 Selector lever sensors control unit K320 Parking lock warning light N110 Selector lever lock solenoid V577 Transverse selector lever lock motor Y5 Selector lever position displayInterface to parking lock holding magnet + (pin A1) Interface to parking lock holding magnet - (pin A2) CAN-High CAN-Low Infotainment CANOnly available in the Audi A4 (Typ 8W) in combination with dual clutch gearboxes of the DL382 series. Refer to page 49.644_071Auto-P function In the case of the automatic gearboxes, the parking lock is electrohydraulically operated. This allows the gearbox control unit to automatically operate the parking lock, thereby enhancing operating comfort. The Auto-P function engages the parking lock automatically (P-ON position) if all of the following conditions are met: • Vehicle stationary – speed 1 kph • Driving position E, D, S, R or M is selected • Engine is not running – terminal 15 OFF In the Audi A4 (type 8W), the drievr can also engage the parking lock by pressing the P button as soon as the vehicle is travelling slower than 2 kph (DL382) or 3 kph (AL552). The parking lock is disengaged automatically (P-OFF position) if the engine is running and drive position E, D, S, R, N or M is selected with the brake applied and the release button pressed.Activating drive position N (P-OFF position)1)To be able to briefly move the vehicle without the parking lock, e.g. in a car wash, automatic engagement of the parking lock can be suppressed. A condition for this is that the selector mechanism, the P button and the gearbox are working properly. The following applies to vehicles with the AL552 gearbox (tiptronic): To activate P-OFF, drive position N must be selected when the engine is running and then the engine must be shut off. When the ignition is turned off, engagement of the parking lock is suppressed for a period of 30 minutes. The following applies to vehicles with the DL382 gearbox (S tronic): In the case of the DL382 gearboxes, the P-OFF position can be engaged with or without the engine running. To activate P-OFF, drive position N must be selected after turning the ignition on