TECHNICAL DOCUMENTATION
SSP 240 AUDI A2 Technology

This PDF is currently unavailable.
Read document text
240Service.AUDI A2 TechnologyDesign and FunctionSelf-study program 240For internal use onlyExciting technology in a new lightweight designThe Audi A2 is paving the way for advanced mobility in the 21st century and at the same time is the first volume-produced car to have an aluminium body. With its future-oriented lightweight design, it represents a new dimension in dynamism and economy.SSP240_025SSP240_026A car for the modern world, innovative, compact, roomy, lightweight, safe and environmentally compatible.2ContentsPage In a nutshell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Engine and gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Running gearFront axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rear axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Components and fitting locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Design and function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ESP control system 30 ESP control system components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diagnosis warning lights and buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 19 20 21 22 23 31 3614Electrical systemVehicle’s electrical system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CAN BUS system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Comfort system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Central control unit for comfort system J393 . . . . . . . . . . . . . . . . . . . . . . Door control units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Anti-theft alarm with interior monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional diagram of comfort system . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 40 44 45 46 50 51 52Heater/ACDesign and function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Additional heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 59 64 68 70Service/maintenanceTechnical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Repair concept of the Audi A2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Special tools / workshop equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76New The self-study programme will provide you with information on design and functions. It is not intended as a workshop manual! For maintenance and repairs please refer to the current technical literature.Attention! Note3In a nutshellBodyAnyone who thinks only steel can be stable obviously hasn’t yet heard about aluminium. Thanks to the Audi Space Frame (ASF)®, the A2’s aluminium body is more than 40 % lighter than the conventional steel design. Its unladen weight is just 895 kg, around 150 kg lighter than other vehicles its size.Drive systemThe high-torque 1.4l 55 kW TDI three-cylinder power unit with pump-nozzle injection uses just 4.2 litres of diesel per 100 kilometres, accelerates from 0 to 100 km/h in 12.1 seconds and has a top speed of 173 km/h. The 1.4 litre four-cylinder petrol engine, also with a power output of 55 kW, allows the Audi A2 achieve similar performance levels and produces a satisfactory average fuel consumption of 6.1 l; the engine is classified as low emissions to EU4 standard.With its 1.2 l three-cylinder TDI engine, Audi will be the first manufacturer in the world to offer a four-door 3-litre car; the launch is scheduled for a later date.4SafetyThe Audi’s outstanding drag coefficient of 0.28 is the best in its class. The Audi Space Frame, made from highstrength aluminium profile sections, surrounds the occupants like a safety cage, thus providing them with a high level of passive safety. Driver, passenger and side airbags are standard. The SIDEGUARD system is optional.Running gearIn the Audi A2, Audi has combined the latest electronic components, such as the standard ABS, EBPD and ESP, with the tried and tested technology of McPherson strut front suspension and a torsion beam rear axle. Thanks to the new electrohydraulic power steering system, optimum steering effort support is provided.SSP240_027MaintenanceLonglife service has been achieved for the above-mentioned engines right from market launch.5BodyThe Audi Space Frame in the Audi A2comprises 183aluminium panels 22extruded profile sections 20cast nodes The front longitudinal members comprise aluminium tubes that can absorb a high level of deformation energy and can be renewed without any welding work being required.SSP240_028The Open Sky roof (optional) has a 58 % larger opening than a normal sliding roof and has a 166% larger transparent area. Detailed information can be found in SSP 239.SSP240_0296Contact corrosion When different metals that are far apart in the electrochemical potential series come into contact, contact corrosion will occur. Contact corrosion can occur if non-Audi approved connecting elements, such as bolts, nuts, washers, rivets, plugs, sockets, adhesives etc, are used. For this reason, the manufacturer only uses connecting elements that have a special surface coating, as well as non-conducting rubber and plastic parts and adhesives. Only Audi approved accessories must be used.Damage resulting from contact corrosion is not part of the warranty. For further information on aluminium technology, please see SSPs no. 160 and 239. Electrochemical potential series (extract) Lead Tin Iron Chromium Zinc AluminiumTherefore only use original Audi A2 partsSSP240_044This is the first time in vehicle design that a one-piece aluminium side-wall frame has been used.To remove the upper B-pillar inner trim on vehicles fitted with SIDEGUARD, the outer Bpillar decorative panel must be unbolted first. Behind the upper rubber grommet is a bolt that must be removed from the outside before the inner trim can be unclipped.7BodyThe Space Floor concept Comprises two floors in the driver and front passenger area; the gap between the two floors accommodates components such as the engine control unit, the control unit for the central locking and the auxiliary relay carrier. This means that the footwell in the rear is lowered (space floor). The rear passengers can bend their legs as normal and assume an ergonomically optimum seating position.SSP240_123 Space FloorFront flap The service module enables oil and washer water to be checked and topped up easily and conveniently. Releasing the quick-release locks behind the service flap enables the bonnet to be raised as well as removed completely.SSP240_031 8SSP240_124Tailgate The lock cylinder in the tailgate has been discontinued. The tailgate is opened via radio remote control (optional) or manually by using the soft-touch button. If the electrical system fails, the tailgate can be opened by using the emergency release cable on the tailgate trim. The actuating handle is set into the tailgate lid.Vehicle identification For clear identification of a vehicle, various representations and locations are used.SSP240_032AUDI AGIn addition to the familiar identification locations in the engine compartment, spare wheel well and the sticker in the service document, the Audi A2 also has both modified and new locations. Type plate in the passenger footwell.01 2 130 3 AUA 000 4451300kg kg 1- 0730kg 2- 0640kgWAUZZZ8ZZYN000276Typ 8ZSSP240_128One new location for the chassis number is the centre tunnel in the rear…SSP240_022* 55 o2 oo YN ZZ Z8 ZZ AU *W… there is also a chromium/nickel plate under false floor on the driver’s side. This plate is bonded and the combination of materials used makes it corrosion resistant.SSP240_084 901 AUA1302 4450003e1 # 98/14 #0131e1 98/ 8ZZY UZZZ WA 1300kg#kg 0kg 073 1- 0640kg 28Z Typ14#AUDI AG0131N000 276BodyDoors The Audi A2’s doors are in two sections. The subframe and door side impact protection have been made into one component. In addition, a protective side bolster protects the pelvis region. The door lock cylinder is held in position with a two-legged clip and a bolt. By turning the bolt clockwise, the clip moves back and the lock cylinder can be removed. In order to remove the door handle, the subframe must first be removed.SSP240_034If an Audi A2 without radio remote control is ordered, the passenger door also has a lock cylinder.SSP240_081Two-stage window lifter switches for front and rear Functions: 1 2 3 4 automatic full closing manual full closing manual full opening automatic full opening123 4 SSP240_035 10Fuel filler flap The fuel filler flap is only operated electrically and is opened from a switch in the B-pillar on the driver’s side. If the electrical system should fail, the emergency release is activated by pushing down the control element for the tank cap.SSP240_036Luggage compartment recess The luggage compartment recess houses: the battery the Tyre Mobility System the vehicle tools the navigation computer (optional) a foam componentThe foam component must remain in place, otherwise the battery may be damaged in the event of a crash.SSP240_03711BodyIsofix On the Audi A2, the Isofix fittings for the rear seats are part of the standard equipment.SSP240_038Isofix fittings are, for the first time, available as optional equipment together with an airbag key switch for deactivating the front passenger airbag.SSP240_039Tearing seamThe outer rear seats are equipped with a 3-point safety belt. Belt force limitation is achieved by means of a pre-defined tearing seam in the belt. This limits the strain level placed on the occupants in the rear seats.SSP239_106 12Notes13Engine and gearboxEngine1.4 l - TDI (55 kW) AMF70 200 180 160 140 120 100 80 60 40 20 0 0 1000 2000 3000 4000 5000 6000Power output [kW]63 56 49 42 35 28 21 14 7 0SSP240_046Technical data Engine code: Design: Capacity: Power output: Torque: Bore: Stroke: Compression: Weight: AMFSSP240_045Firing order: Mixture induction: Turbocharger:1-2-3 Direct injection with pump-nozzle unit Garrett GT 12 turbocharger with wastegateTurbocharged threecylinder in-line engine 1422 cm3 55 kW (75 PS) at 4000 rpm 195 Nm at 2200 rpm 79.5 mm 95.5 mm 19.5 : 1 130 kgExhaust emissions control: Oxidising catalytic converter and exhaust gas recirculation Exhaust emissions standard: EU 3 Fuel: Diesel, cetane rating at least 49 CN, RMEPlease refer to SSP 223 for the design and function of the 1.4 l TDI pumpnozzle engine.The engine code and engine number are located on the front engine/gearbox flange.SSP240_047 14Torque [Nm]1.4 l - 16 V (55 kW) AUA70 63 200 180 160 140 120 100 80 60 40 20 0 0 1000 2000 3000 4000 5000 6000Power output [kW]56 49 42 35 28 21 14 7 0SSP240_048SSP240_049Technical data Engine code: Design: AUA Four cylinder in-line engine Petrol engine 1390 cm3 55 kW (75 PS) at 5000 rpm 126 Nm at 3800 rpm 76.5 mm 75.6 mm 10.5 : 1 90 kg Ignition system: Firing order: Mixture induction: 1-3-4-2 Electronic, sequential multipoint injection, adaptive idlecompensation, overrun cut-off Distributorless ignition system with static highvoltage distribution, long-life spark plugsCapacity: Power output: Torque: Bore: Stroke: Compression: Weight:Exhaust emissions control: 3-way catalytic converter, 2 heated lambda probes, activated charcoal filter Exhaust emissions standard: EU 4 Fuel: Petrol, unleaded, 95 RON Please refer to SSP 247 for a description of the design and function of the1.4 l engine.– Lambda control with probes upstream and downstream of the catalytic converter (EOBD) – Electric exhaust gas recirculation valve – Valve actuation via rocker armsSSP240_050 15Torque [Nm]Engine and gearboxReadiness code The readiness code is an 8-digit code that indicates the status of the diagnoses relevant for emissions. In normal vehicle operation, the diagnoses are carried out at regular intervals. When using EOBD (Euro On-Board Diagnosis) it is recommended that the readiness code, address word 01 (function 15) is generated after repairs to emissions-relevant systems have been carried out. This enables a repair to be checked immediately.Meaning of the 8-digit number block for the readiness code The readiness code is only generated when all the displays are 0 1 2 3 4 5 6 7 8 0 0 0 0 0 0 0 0 Diagnosis function Catalytic converter Always “0” Activated charcoal filter system (fuel tank breather system) Always “0” Always “0” Lambda probes Lambda probe heater Exhaust gas recirculation systemOnce the diagnosis for a system (e.g. lambda probes) has been run successfully, the corresponding position in the code will switch from 1 to 0.Please refer to the workshop manual for a more detailed description of the procedure.16Gearbox02J gearbox 02T gearboxSSP240_052SSP240_051The familiar 02J gearbox is used in the Audi A2 1.4 l TDI, and is suitable for torques of up to 250 Nm.The 02T gearbox is an extremely lightweight two-shaft gearbox. The housing components are made of magnesium. It is designed to transmit torque values of up to 200 Nm.Please refer to SSP 247 for a description of the design and function of the 1.4 l engine .Both gearboxes are actuated via gear selector cables and gate selector cables.SSP240_054 SSP240_05317Running gearFront axleThe front axle of the Audi A2 comprises McPherson struts and lower A-arms that are bolted to the wheel bearing housings and the console of the subframe. The camber can be evened out by moving the subframe and the two front consoles. The toe is set separately on the right and left-hand sides by means of the track rods. To reduce roll when cornering, an anti-roll bar has been fitted whose actuating arms are located directly below the spring plates. The coil springs have large supporting bases in the suspension strut and are installed with their axes offset to minimise lateral forces. Spring and damper forces are applied to the body separately to increase ride comfort.SSP240_05518Rear axleThe rear axle is a torsion beam axle. It is bolted to the body by means of stirrupshaped aluminium profile sections. The large guide bearings are arranged at an angle of 25 degrees to the transverse axis to minimise undesirable toe-out. The springs and shock absorbers are arranged separately to maximise the width of the luggage compartment. The toe can be set to be symmetrical by moving the “stirrups”. The camber cannot be adjusted. The axle crossmember is made from hydroformed, thin-walled tube. Its V-shaped profile in the centre, that widens out towards the ends, makes the axle crossmember resistant to bending but relatively compliant to torsion. This means an additional anti-roll bar is not required.SSP240_05619Running gearPower steeringThe system pressure required to provide steering assistance is generated by means of a hydraulic pump. On the traditional, familiar power steering system, the pump is driven directly by the vehicle engine. Some of the engine power is therefore always required to operate the pump. When steering assistance is needed the most – i.e. when manoeuvring – the engine speed is at its lowest. The pump output is designed for these conditions. The faster the steering speed, the higher the pump speed and therefore the volumetric flow rate. At higher engine speeds, the unwanted pump output is discharged via a bypass system. In the new steering system, the hydraulics still provide assistance to the steering effort supplied by the driver, but this time the hydraulic pump – a gear pump – is driven by an electric motor and is mechanically independent of the vehicle engine. A new feature is the steering angledependent steering effort assistance. For this, a steering angle sensor is located above the steering-gear housing, see Page 26, Fig. SSP240_059; the sensor transmits the steering angle speed to the electronic control system. The steering angle information is sent directly to the control unit via a sensor cable. The road speed is also recorded in the control unit during the evaluation. This information is sent via the CAN bus. The adjacent diagram shows the structure of the system.SSP240_05720Components and fitting locationsWarning lamp for Servotronic K92K92The warning lamp is integrated into the dash panel insert (driver information system). Self-diagnosis is done using address word 17 (instrument cluster).Power steering sensor G250 The sensor is located in the valve dome of the power-assisted steering box. It records the steering angle and calculated the steering angle speed. If the sensor should fail, the steering function is still guaranteed. The power steering shifts to a programmed emergency running mode. The steering forces required are greater. Error functions are stored in the power steering control unit J500.J500G250SSP240_083Power steering control unit J500 The control unit is integrated into the motor/ pump unit. It converts the signals for driving the gear pump as a function of steering angle speed and road speed. The delivery rate required at any particular moment is read from a map stored in the control unit. It detects and stores faults that occur during operation. An anti-pumping device and a thermal protection facility are integrated into the control unit. The diagnosis connection is located in the driver’s storage compartment.Volumetric flow rateRoad speedSSP240_130The power steering control unit cannot be replaced separately.S sp tee ee rin d gan21gleRunning gearOverview of systemWarning lamp for Servotronic K92 Road speed sender G22Control unit for 4LV J357Control unit with display in dash panel insert J28590 60 120 °C 1/2 1/13 2 14 5 620 40607080km/h50 30 100100120 140160180200220240Sensor for power steering G250Steering angle speed signalBanjo bolt with non-return valveReservoir for hydraulic fluid Pressure limiting valveCANRoad speed signalPower assisted steering gearCANGear pump Power steering J500 control unitPower steering terminal +30 Power steering terminal +15 Earth –MElectric motor SSP240_05822CANEngine speed signalDesign and functionThe EPHS (Electrically Powered Hydraulic Steering) steering system is a power steering system that operates as a function of steering angle speed and road speed.The pump, V119, for the steering hydraulics comprises a gear pump and an electric motor.Anti-pumping device The electrohydraulic power steering has an anti-pumping device that is actuated in the event of faults, a failure or a crash.Instead of the vane pump that is traditionally used on conventional power steering systems, this system uses a gear pump that is integrated into the motor/pump unit. The gear pump is not driven directly by the vehicle’s combustion engine; instead it is operated by an electric motor integrated into the motor/pump unit. The electric motor only operates when the ignition is switched on and the engine is running. Signals for steering angle speed, road speed and engine speed are sent to the control unit. This control unit regulates the speed of the electric motor and the gear pump, and thereby regulates the delivery rate or the volumetric flow rate of the hydraulic fluid.The anti-pumping function can be cancelled by switching off the ignition and restarting the engine. If necessary, wait approx. 15 mins to allow the motor/pump unit to cool down after overheating. If, after waiting for this period, the anti-pumping function cannot be cancelled by starting the engine, there is a fault in the vehicle electrical system or the motor/pump unit is faulty. In this case carry out a self-diagnosis and if necessary renew the motor/pump unit.23Running gearTorsion bar Power steering sensor G250Return linefrom the gear pump Non-return valveRotary valveControl sleeveAs with the familiar power steering, the hydraulic control unit contains a torsion bar that is connected on the one side with arotary valve and on the other side with the input pinion and the control sleeve.Straight-ahead driving In straight-ahead driving situations, the torsion bar holds the rotary valve and the control sleeve in a neutral position. The power steering sensor does not detect any steering angle. The fluid flows through the hydraulic control unit at virtually no pressure and returns to the reservoir via the return line. The control grooves on the rotary valve and the control sleeve are in a neutral position with respect to each other so that the oil can enter both sides of the working cylinder and can run off to the reservoir via the return grooves on the control sleeve.Control sleeve Rotary valvedFeed lineb to the working cylinder, left-hand sideSSP240_077c a to the working cylinder, right-hand sideReturn lineSSP240_075 24to the working cylinder, lefthand side to the working cylinder, right-hand side Piston working cylinderSSP240_074From a hydraulics point of view, the function positions “right steering lock” and “left steering lock” are similar to the familiar power steering system.Left steering lock The deformation of the torsion bar results in the rotary valve being twisted against the control sleeve. The control grooves of the rotary valve release the pressurised fluid feed to the right-hand side of the working cylinder. The pressurised fluid flows into the working cylinder and provides assistance for the steering motion. At the same time, the rotary valve closes the feed to the left-hand side and opens the return from the left-hand side of the working cylinder. The pressure on the right-hand side forces the oil from the left-hand side of the working cylinder into the return line. When the steering manoeuvre is completed, the torsion bar ensures that the rotary valve and the control sleeve return to the neutral position.Control sleeve Rotary valveb dto the working cylinder, left-hand sideFeed line SSP240_078a cReturn lineto the working cylinder, right-hand side SSP240_076 25Running gearPower steering sensor G250Steering boxReservoirGear pumpPower steering control unit J500 Pump motorSSP240_059The hydraulics also provide assistance for the steering effort provided by the driver on the new steering system. The hydraulic gear pump is driven by an electric motor and is therefore independent of the vehicle engine. A new feature is the steering angledependent steering assistance.Power steering sensor G250 RotorAt a later date on the Audi A2 the signal from the steering angle sender G85 (see Page 33) will be used, thus eliminating the need for the power steering sensor G250.Input shaftSSP240_06026Description of the power steering sensor G250 (capacitive sensor) A rotor that is attached to the input shaft rotates in between 9 small plate capacitors. This detunes the capacitance of the plate capacitors. From this change in capacitance, the sensor’s electronics calculate signals (steering angle and steering speed) for the power steering control unit.Schematic diagram of capacitor detuningRotor Capacitor electrodes Sensor electronics SSP240_119Top viewInput shaft withrotorto the power steering control unitCapacitor electrodes SSP240_042 Sensor electronics 27Running gearThe motor/pump unit consists of: – the hydraulic unit with gear pump and electric motor – the reservoir for the hydraulic fluid – the control electronics for the electrohydraulic steeringScrew capReservoirThe left-hand headlamp must be removed first in order to check/top up the hydraulic fluid. Under no circumstances must the pressure and return lines for the power steering be detached. Otherwise the plastic inserts in the pipes might be damaged. If the pressure and return lines are lifted clear and tied in place, the bending radius must not be less than the minimum radius of 100 mm.Terminal Return lineGear pumpTerminal Pressure hoseThe power steering control unit J500 converts the incoming – engine speed (G28) – road speed (G68) – and steering speed (G250) signals to drive the gear pump; this is done as a function of steering angle and road speed.Rubber bushPower steering control unit Electric motor SSP240_079Self-diagnosis is done via the instrument cluster (address word 17) . Communication is exclusively via the drive system CAN bus.90 60 120 °C1/2 1/134 5 620 40607080km/hError messages are output via the instrument cluster.2 150 30 100100120 140160180200220240SSP240_082 28Pump operationIgnition on offVehicle engine running stationary, road speed = 0 km/hElectricpump running not runningSteering assistance available nonesteering assistanceRoad speed low e.g. parkingSteering angle speed highDelivery rate highSteering assistance high (light steering)high e.g. motorway drivinglowlowlow (heavy steering)29Running gearESP control system3 11 122CHECK CONTROL ESPESP TCS EDL EBP Over4 5 6 7 17 818CHECK9 10 13 14 15 1 1916SSP240_062 1 2 3 4 5 6 7 8 9 Control unit for ABS with EDL/TCS/ESP J104 Hydraulic unit N55 with charging pump V64 Brake pressure senders 1 and 2 G201/G214 Lateral acceleration sender G200 Speed sensor G202 Button for TCS/ESP Steering angle sender G85 Brake light switch … 12 active speed sensors G44 … G47 13 14 15 16 17 18 19 Diagnosis wiring Warning lamp for braking system K118 Warning lamp for ABS K47 Warnign lamp for TCS/ESP K155 Vehicle and driver behaviour Cut-in to engine management Cut-in to gearbox control system (vehicles with automatic transmission only)The rotational speed sensors supply the wheel speed information continually for each individual wheel. The steering angle sensor is the only sensor that supplies its data directly via the CAN bus to the control unit. The control unit uses both pieces of information to calculate a target steering direction and target vehicle behaviour.The lateral acceleration sensor reports to the control unit if the vehicle is breaking away to the side, whilst the rate of rotation sensor reports if the vehicle is tending to skid. Using these two pieces of information, the control unit calculates the current condition of the vehicle. If the target and actual values differ, a control intervention is calculated.30ESP decides: – which wheel is braked or accelerated and by how much, – whether the engine torque should be reduced and – on vehicles with automatic transmission, whether the gearbox control unit needs to be activated.Afterwards, the system checks by using the incoming data from the sensors, to see if the intervention has been successful: – if yes, the intervention is completed and the behaviour of the vehicle continues to be monitored. – if no, the control sequence is run again. If a control intervention is being carried out, the ESP lamp will flash to inform the driver of this.ESP system componentsThe active brake servo In addition to the usual function of boosting the pressure exerted by the driver’s foot on the brake pedal by means of a vacuum from the intake pipe or from a vacuum pump, the servo also has the task of generating the initial pressure for an ESP intervention. This is necessary because the intake performance of the return pump is not always sufficient to generate the required pressure. The reason for this is the high viscosity of the brake fluid at low temperatures. If an ESP control action is imminent the solenoid, activated by the control unit, pulls the metal core forwards and opens valves within the valve piston solenoid unit. As when the brake pedal is actuated, this builds up an initial pressure in receptacle 1 (receptacle 2 remains empty) and thereby generates the pressure in the braking system which is then monitored by two brake pressure senders.SSP240_063Receptacle 1 Receptacle 2 Solenoid Metal core31Running gearSenders 1 (G201) and 2 (G204) are duplicate designs to guarantee the maximum possible safety. They are capacitive sensors and designed as plate capacitors. If braking pressure is exerted on the moving plate, the gap between the two plates is reduced and the capacitance increases. The change in capacitance is a direct measure of the change in pressure and provides measurements to calculate the brake forces and the pre-charging control.SSP240_065Control unit for ABS with EDL/TCS/ESP J104The control unit for ABS/EDL, J104, is combined with the hydraulic unit to form one module. Both components can be renewed separately. It is not necessary to remove the entire unit when doing this. Function – Control of ESP, ABS, EDL, TCS, EBPD and overrun torque limiting functions, – continuous monitoring of all electrical components and – diagnosis aid for repair workSSP240_06132Relay for brake light suppression J508 When the ESP system switches on the solenoid, the brake pedal can move so much, because of the tolerances that arise, that the brake light switch closes the contact to the brake lights. To avoid irritating following drivers, relay J508 interrupts the connection to the lights for as long as the solenoid is activated.J104M25 M9 J508 F/F47SSP240_066Steering angle sender G85 The coil connector with slip ring forms the electrical connection between airbag control unit and the driver’s module in the steering wheel. The coil connector housing also accommodates the steering angle sensor (G85) which transmits the steering angle to control unit J104 via the CAN bus (see SSP 204).Coil connector with slip ring for the driver’s airbagSSP240_067After renewing the airbag coil spring/ steering angle sensor, a basic setting must be carried out.33Running gearSenders G200 and G202 are mounted on a common bracket. This is located near to the centre of gravity of the vehicle, on the tunnel between the centre console and the bulkhead.G200The lateral acceleration sender G200 calculates the vehicle’s lateral acceleration.G202Sender for rate of rotation (G202) measures the rate of rotation/yaw rate of the vehicle about the vertical axis.The signals from the two senders enable control unit J104 to determine the current actual driving conditions. From these, the control components required for optimum driving conditions are derived.SSP240_141Button for TCS E256 The ESP function cannot be switched off on the Audi A2. The TCS function can be deactivated via a button (up to a speed of 50 km/h). For further information on ESP, please refer to SSP 204.SSP240_069+SJ104L71E256SSP240_07034The new active wheel sensor for ABS A sensor is considered to be an active sensor if it needs an external power supply in order to perform its function.South Sensor electronicsThe active speed sensor has a magnetoresistive element. Its resistance changes as a function of the magnetic lines of force intersected by the sensor ring/read track.SouthThe sensor ring on the wheel hub comprises a read track with different fields magnetised to the north and south pole. The sensor ring rotates on the stationary sensor element. Operating principle of the active sensor In the immediate vicinity of the magnetised areas, the magnetic lines of force stand vertical on the read track. Depending on the polarity, they are either running away from the track or towards it. Because the distance between the read track and the sensor is very small, the lines of force penetrate the sensor element and change its resistance. An electronic booster/trigger circuit incorporated into the sensor converts the changes in resistance into two different current levels.Sensor elementNorthNorth Read track SSP240_071 SouthΩNorthThis means that, if the resistance of the sensor element increases because of the direction of the magnetic lines of force running through it, the current will drop.SouthIf the resistance falls because of a change in direction of the lines of force, the current increases. Since the north and south poles alternate on the rotating read track, a square wave signal sequence is produced which enables the frequency to be a measure for rotational speed.SSP240_072Advantages – The rotational speed of the wheel can be measured from 0 km/h and until the wheel is stationary. – The direction of rotation of the wheel is detected. – high corrosion resistance – Compact installation35Running gearDiagnosis warning lamps and buttonsIf a fault occurs during a control action, the system will try to bring the intervention to an end in the best way possible. After the control action has ended, the sub-system concerned will be switched off and the warning lamps will be activated. The error that occurred and the activation of the warning lamps will be stored in the fault memory.Warning lamps/buttons Warning lamp for braking system K118ABS warning lamp K47TCS/ESP warning lamp K155Button for TCS The TCS function can be switched off with the TCS button.Key ESP TCS ABS EBPDBWL Electronic Stability Program Traction Control System Anti-lock Braking System Electronic Brake Pressure Distribution Brake Warning Lamp36ABS/ESP/BWL lamp activation - Audi A2 Warning lamps System status Brake K118 ABS K47 ESP K155 TCS button E256 (only TCS off)Ignition on. Test run for approx. 2 s. Undervoltage Suppresses BWL activation for 10 s every time undervoltage is detectedAfter 10 s, BWL on System OK TCS/ESP interventionflashes ESP intervention TCS off via buttonflashes TCS button off ABS and ESP remain active (currently no ESP intervention)actuatedactuated ESP failure ESP failure TCS button on, i.e. ESP lamp was already on actuated ABS/ESP failure Emergency EBPD remains active EBPD failure all systems switch off37Electrical systemVehicle electrical systemThe electrical/electronic connector stations and the control units have also been decentralised on the Audi A2. This ensures optimum wiring routing.Dash panel insert Diagnosis interface for data bus (gateway) J533 Display instruments Control unit with display unit in the dash panel insert J28590 60 120 °C 1/2 1/1Door control units in the window lifter motors passenger side J387 rear right, optional J3893 2 14 5 620 40607080km/h50 30 100100120 140160180200220240E-box false floor at the front on the right-hand side Connection point 1. Bose amplifier2. Power amplifier3. Telematics control unit J499 4. Control unit for mobile phone control electronics J412 Connection point – A-pillar, right-hand sidePower steering control unit J500Radiator fan control unit J293Control unit for ABS/ESP J104 38Lateral acceleration sender G200 and sender for rate of rotation G202CD changer R41 False floor luggage compartment: Control unit for navigation system operating electronics J402 Aerial diversity Acoustic parking system control unit J446BatteryAirbag control unit J234SSP240_041Door control units in the window lifter motors driver’s side J386 rear left, optional J388Auxiliary relay carrier False floor on the front left-hand side Connection point E-box false floor on the front left-hand side Control unit for 4LV J357 Automatic gearbox control unit J217 Central control unit for comfort system (CCU) J393 Connection point A-pillar 39Electrical systemCAN bus systemA substantially expanded CAN bus system has been installed in the Audi A2.2 1Control unit with display in dash panel insert J28590 60 120 °C 1/2 1/134 5 620 40607080km/h50 30 100100120 140160180200220240Radio ChorusGatewayTRACK SEEK EJECT FR FFTUNESCAN AS TPDiagnosis systemCD1CDC AM FM21 EJECT BASS23456Audi symphony MIDDLE TREBLEDOLBY SYSTEM12BALANCEFADERRDS RANDOMPLAYTAPESDERadio Symphony J446 Acoustic parking system control unit E87 Operating and display unit for air-conditionerJ537 Control unit for 4LVJ393 Central control unit for comfort system J217 Automatic gearbox control unitJ402 Control unit for navigation system operating controls+R TJ104 Control unit for ESPJ386 Door control unit, driver’s sideJ387 Door control unit, passenger sideJ453 Multifunction steering wheel interface J412 Control unit for mobile phone control electronics Voice control systemSteering angle sender G85J388 Door control unit, rear leftJ389 Door control unit, rear right500 kBaud drive system bus 100 kBaud comfort bus Power steering control unit J500100 kBaud display bus Diagnosis connectionA transmission speed of 500 kBaud has been selected for the drive system bus sub-system to enable fast data transfer within systems that are vital for safety.A lower transmission speed of 100 kBaud is sufficient for the two comfort and display sub-systems. However, these systems have been kept separate to keep functional failures low in the event of a fault in the CAN bus sub-system.40Gateway in the dash panel insert The task of the gateway in the dash panel insert is to facilitate the exchange data between the three CAN bus sub-systems, i.e.: – the drive – comfort and – display (Infotainment) systems Direct communication between these subsystems is not possible on account of the different transmission speeds.SSP240_088To exchange information between these subsystems a connection or an access gateway is required.The gateway filters the data sets arriving from the bus sub-systems and transfers only the data that the other bus needs.Example of a data exchangeAutomatic gearbox control unit J217Central control unit for comfort system (CCU) J393Control unit for 4LV J357kB500 kBaudaud90 60 120 °C1/2 1/13 2 14 5 620 40607080km/h50 30 100Operating and display unit for air-conditioner E87100 kBaudDiagnosis interface for data bus in the dash panel insert J285TEMP10100120 1401600Data message180200220240OFFSSP240_08941Electrical systemWhen fault finding, note that error functions of sub-systems connected to the gateway can be caused by a fault in the dash panel insert or within another CAN bus sub-system.VAS 5051 Vehicle diagnosis, measuring and information system Version -D- / V15.00 10/11/1999Vehicle self-diagnosisMeasuring equipmentSSP240_090Guided Fault findingVehicle self-diagnosisSelect vehicle systemAdministrationHelp01 – Engine electronics 41 – Diesel pump electronics 02 - Gearbox electronics 12 – Clutch electronicsTo enable a dialogue between the central comfort unit - address word 46 – and the diagnosis tester, switch the ignition to the “Ignition on” position55 – Headlamp levelling control 16 – Steering wheel electronics 26 – Electronic roof operation 36 – Seat adjustment, driver’s side 46 – Central module – comfort system 56 - Radio 66 – Seat/mirror adjustment 76 – Acoustic parking system 17 – Dash panel insert 08 - Electronic climate/heating control 18 - Additional/auxiliary heater Interrogating theself-diagnosis fault memory – whole vehicle Vehicle Select vehicle system by means of the address word Vehicle system not available Measuring Skip Printequipment46 – Central module – comfort systemHelpThe central comfort unit does not have a connection for the “ignition on” signal (terminal 15). This information is transferred from the dash panel insert to the central comfort unit via the CAN bus. For further information on the central comfort unit, see Page44onwards. If therefore the function has no dialogue, the cause may be – in the dash panel insert/display – in its voltage supply – in the CAN bus connection to the gateway and the central comfort unit .SSP240_017SSP240_092 42Immobiliser III The control unit, J334, for the immobiliser is integrated into the instrument cluster in the dash panel insert J285 or J218. If the control unit is faulty, it is possible, with diagnosis tester VAS 5051, model CD , version 15 onwards, to quickly download the data from the instrument cluster via “Guided fault finding”; the data can then be programmed into the new one. Select “Skip” to go to the Select Function/ Component menu.Guided fault finding Function/component selection Select function and component Drive system (Rep. Gr 10 – 39) Running gear (Rep. Gr 40 -49) Body (Rep. Gr 50 -97) Workshop equipment Connectors Control unit functionsAudi V15.00 10/11/1999 Audi A2 1999 2000 (Y) Saloon, 5-door AUA 1.4 l MARELLI 4LV/55 kWGuided fault finding Function/component selection Select function and componentMeasuring equipment Vehicle self diagnosis Skip destination Print HelpAudi V15.00 10/11/1999 Audi A2 1999 2000 (Y) Saloon, 5-door AUA 1.4 l MARELLI 4LV/55 kWControl unit functions 01 – Engine electronics 02 - Gearbox electronics 03 - Brake electronics 15 - Airbag 17 – Instrument cluster 35 - Central locking system Guided fault finding Function/component selection Select function and component Audi V15.00 10/11/1999 Audi A2 1999 2000 (Y) Saloon, 5-door AUA 1.4 l MARELLI 4LV/55 kWMeasuring equipmentVehicle self diagnosisSkip destinationPrintYou are guided through the program by means of menus; the adaptation values are read out from the old instrument cluster and then transferred into the new instrument cluster, see diagram.Control unit functions 17 – Instrument cluster Renew instrument cluster Help Code instrument cluster Reset service interval display after a service Adapt the fuel gauge Adapt fuel consumption display Adapt the language version Adapt the vehicle keyMeasuring equipmentVehicle self diagnosisSkip destinationPrintHelpGuided fault finding Function/component selection J218 – Read out data Transfer dataAudi V15.00 10/11/1999 Audi A2 1999 2000 (Y) Saloon, 5-door AUA 1.4 l MARELLI 4LV/55 kWGuided fault finding Function/component selection J218 – Renew instrument cluster Adapting the immobiliserThe data is transferred into the new instrument cluster.Audi V15.00 10/11/1999 Audi A2 1999 2000 (Y) Saloon, 5-door AUA 1.4 l MARELLI 4LV/55 kWFinishedTo adapt the immobiliser and the vehicle keys the following programs must be run: “J218 – Combined processor, adaptation to engine control unit” “Key matching” END OF TESTMeasuring equipmentVehicle self diagnosisSkip destinationPrintHelpMeasuring equipmentVehicle self diagnosisSkip destinationPrintHelpSSP240_093 43Electrical systemComfort systemThe comfort system has been installed in the Audi A2 for the first time. The comfort system comprises the central comfort unit and at least two door control units.The following functions are performed Standard equipment: – – – – – Central locking Electric window lifters at the front Comfort closing Interior lighting Exit lights – – – – Optional: Radio remote control Electric window lifters at the rear Anti-theft alarm with interior monitoring Electric Open-Sky roofAs a result, there are two different variants: – A central control unit with two door control units, if electric window lifters are only installed in the front doors.SSP240_094– A central control unit with four door control units, if electric window lifters are installed in all the doors.44Central control unit for comfort system J393The central control unit for the comfort system forms the Central Comfort Unit (CCU) and is incorporated into the comfort CAN bus system. The following information is processed in the control unit and made available to other equipment:Control unit with display in dash panel insert J285 Fuel filler flap release – Switch for remote release/ fuel filler flap E20490 60 120 °C 1/2 1/1If the rear doors do not have electric window lifters and therefore no door control units, the control of the central locking for the rear doors is taken over by the CCU.Fuel filler flap – Motor for tank cap locking V1553 2 1 4 5 620 40Tailgate release – Tailgate closed switch F206 – Button for release, tailgate lock cylinder F248 – 3. Remote control button Anti-theft alarm – Contact switch for bonnet F120 – Glass break sensor, rear window G304 – Earth contact, radio – Switch for interior monitoring E183 – Sensor for interior monitoring G209 Aerial for central locking and antitheft alarm system R47 Handbrake switch F9 Crash signal Reversing lamp M17 Switch for heated rear window and exterior mirrors E161 when mechanical window lifters are fitted in the rear607080km/h50 30 100100120 140160Tailgate – Motor for tailgate release V139200180 220240Anti-theft alarm – Horn for anti-theft alarm H8 Interior light control – Interior light dimming – Luggage compartment lamp activation Enable for door control units and Open-Sky roof Comfort locking – Window lifter – Open-Sky roof Comfort opening – Window lifter – Open-Sky roof Mirror heating to the door control unitsGatewayJ393 Central control unit for comfort systemDiagnostics connector– Door contact signal – Locking signal – Deadlock signalwhen mechanical window lifters are fitted in the rear – Lock motor – Deadlock motorJ386 Door control unit, driver’s sideJ387 Door control unit, passenger sideJ388 Door control unit, rear leftJ389 Door control unit, rear right 45Electrical systemDoor control unitsThe door control units are integrated into the housing for the window lifter motors and require the following signals:Door control unit Window lifter switch Enable through central comfort unit Door lock feedback signal – Door contact signal – Locked signal – Deadlock signal Additionally for the front doors – Switch for releasing and locking the lock cylinder (passenger door, not if remote control fitted) In addition for the driver’s door – Central locking switch – Switch for childproof lock on rear window lifters – Central window lifter operation – Changeover switch for mirror adjustment – Switch for mirror adjustment Door locking and release Deadlocking and unlocking of the doors Electric window lifter with excess force limitation Switch illumination control system, exit lights Additionally for the front doors – Driver’s door check LED control system – Electric mirror adjustment – Mirror heatingComfort CAN46The window lifter motors are controlled by means of an excess force limitation system. A Hall sensor determines the rotational speed of the motor shaft. If the door window encounters an obstacle, the Hall sensor detects the change in the motor’s rotational speed. The door control unit then reverses the direction of the window.Hall sensorSSP240_104Window lifter switch270100820J393E40CAN KomfortMJ386 J387V14MV15MThe window lifter switches have two stages. 1. Stage 1, manual full closing or full opening 2. Stage 2, automatic full closing or full openingJ388 J389V26MV27SSP240_14247Electrical systemDoor lock Each door lock has two electric motors incorporated into it, one for locking and releasing and one for deadlocking/unlocking. In addition there are also the following microswitches in the door locks. – – – – – Locking via lock cylinder (front only) Releasing via lock cylinder (front only) Lock locked Lock deadlocked Door contact via 2nd catch on lock latchLock open Micro-switch for opening lock cylinderLock locked and deadlockedMicro-switch for central locking (deadlocking)Micro-switch for closing lock cylinder Micro-switch for central locking (locking)Motor for central locking (locking/releasing)SSP240_107 Motor for central locking (deadlocking/unlocking)SSP240_108If the vehicle is fitted with remote control, the lock cylinder is not fitted to the passenger door.48Control system for Open-Sky roof For safety reasons, the comfort locking function on the Open-Sky roof is only activated via the lock cylinder in the door and not via the remote control. The comfort opening function can also be activated via the remote control.SSP240_109The check LED lamp serves to indicate to the driver when locking the vehicle that there is a fault with the comfort system or the anti-theft alarm. 30 seconds after locking, the LED lamp will flash at a frequency of 0.5 Hz, regardless of whether there is a malfunction. This is so that a system malfunction is not evident outside the vehicle.LED signals in the driver and passenger doors (anti-theft alarm not fitted)Central locking OK0,5 HzCentral locking faultyContinuous signal for 30 s0,5 Hz02s25 s30 s[t]SSP240_110LED signals in the driver and passenger doors (with anti-theft alarm and infrared monitoring)Central locking, anti-theft alarm and infrared monitoring OK Central locking and anti-theft alarm active Infrared monitoring faulty Central locking faulty or Infrared monitoring faulty0 2s 3,3 Hz 1,0 Hz 0,5 HzNo signalContinuous signal for 28 s25 s30 s[t]SSP240_11149Electrical systemAnti-theft alarm with interior monitoringSSP240_112The comfort system in the Audi A2 can be fitted with an anti-theft alarm and ultrasonic interior monitoring as optional equipment. The position of the sensors for the interior monitoring does not allow the luggage compartment to be monitored. Therefore, a glass breakage sensor has, for the first time, been installed in the rear window. This prevents anyone from gaining unauthorised access by breaking the rear window. When the anti-theft alarm is activated, a wire incorporated into the rear window is checked continually by the central comfort unit for continuity. Any interruption is registered by the central comfort unit which then triggers the alarm.J393 Central control unit for comfort system (CCU)H8 Horn for anti-theft alarm SSP240_11350Diagnostics The comfort system has diagnostic capabilities. Address word 46 The self-diagnosis of the entire comfort system is transmitted via the central comfort unit where it is placed on the K-line. The door control units do not have their own address word. Self-diagnosis can only be called up with “ignition on”. In the “coding control unit” function it is possible to activate special functions by adding additional values to the standard coding, for example – selective central locking – disable rear release after a specific speed threshold has been exceeded – lock all doors after a specific speed threshold has been passedJ393 Central control unit for comfort system (CCU)J386 Door control unit, driver’s sideJ387 Door control unit, passenger sideJ388 Door control unit, rear leftJ389 Door control unit, rear right COMFORT CAN SSP240_114For additional values and other options, please refer to the coding table in the current repair manual. In the “adapt channel 21” function, it is possible to match a remote control key even without a second key. Channel 60 informs the central comfort unit whether an air-conditioner operating panel is present. This is required for controlling the mirrors via the rear window heater. The system variant is set using channel 61. Information as to whether two or four door control units are installed in the system is input here.Vehicle self-diagnosis 10 - Adaption Channel 21 - reading and testing46 – Central module – comfort system 8Z095943C Comfort unit T05 0100 Code 4672 Dealership No. 2154Key AdjustingVehicle self-diagnosis 10 - Adaption Channel 60 - reading and testingMeasuring equipment Skip Print Keypad46 – Central module – comfort system 8Z095943C Comfort unit T05 0100 Code 4672 Storing Dealership No. 2154HelpAir conditioner KD Control unit activatedKeypadMeasuring equipmentSkipPrintHelpSSP240_11551Electrical systemFunctional diagram Comfort systemE39 E40 E40 E43 E48 E52 E53 E54 E55 E107 E150 E183 E204 F2 F3 F9 F10 F11 F120 F131 F132 F133 F134 F147 F148 F206 F241 F242 Rear window lifter isolation switch Front left window lifter switch Front right window lifter switch Switch for mirror adjustment Changeover switch for mirror adjustment Rear left window lifter switch Rear left window lifter switch, driver Rear right window lifter switch Rear right window lifter switch, driver Window lifter switch, in passenger door Interior locking switch, driver’s side Switch for interior monitor system Switch for remote release of fuel filler flap Door contact switch – driver’s side Door contact switch – passenger side Handbrake check switch Rear left door contact switch Rear right door contact switch Contact switch for Front Top anti-theft alarm Front left actuator for central locking Rear left actuator for central locking Front right actuator for central locking Rear right actuator for central locking Make-up mirror contact switch – driver’s side Make-up mirror contact switch – passenger side Tailgate closed switch Contact switch in lock cylinder, driver’s side Contact switch in lock cylinder, passenger side (vehicles without remote control) Actuator for central locking (deadlock), driver’s door Actuator for central locking (deadlock), passenger door Actuator for central locking (deadlock), rear left door Actuator for central locking (deadlock), rear right door F248 G209 G304 H8 J285 J386 J387 J388 J389 J393 M27 R47 S V14 V15 V17 V25 V26 V27 V56 V57 V97 V115 V139 V155 V161 V162 V163 V164 W W3 W13 W14 W19 W20 W43 Release button, tailgate lock cylinder Ultrasonic sensor for anti-theftalarm Glass break sensor, rear window Horn for anti-theft alarm Control unit with display in dash panel insert Door control unit, driver’s side Door control unit, passenger side Rear left door control unit Rear right door control unit Central control unit for comfort system Left door warning light Aerial for central locking and antitheft alarm system Fuse Left window lifter motor Right window lifter motor Motor for mirror adjustment (driver’s side) Motor for mirror adjustment (passenger side) Rear left window lifter motor Rear right window lifter motor Central locking motor - driver’s door Central locking motor - passenger door Central locking motor – right rear door Central locking motor – left rear door Motor for tailgate release Motor for tank cap release Central locking motor (deadlock), driver’s door Central locking motor (deadlock), passenger door Central locking motor (deadlock), rear left door Central locking motor (deadlock), rear right door Front interior light Luggage compartment light Reading light, passenger side Illuminated make-up mirror (passenger side) Reading light, driver’s side Illuminated make-up mirror (driver’s side) Rear interior lightF243 F244 F245 F2465258s W20 W W14R47E107 30100 270 820E54100 270 820F134 F11 F246V97V16458sS39 10A S 30AM MW43 V139ME204 V155MF248F206H8 J387V15MV27MJ389W19W13F147F148W3F3 F244 F242 F133MMMMCAN-H CAN-LV57V162Z5V25J393J39370 1SE150 K 6 5 4 3 2 1 G304 E48 E430 1FM27V14J285V26MJ386F120 G209 F9 E183J386MJ388Z4 Z4 1 2 3 4Heated exterior mirror, driver’s side Heated exterior mirror, passenger side Radio earth break for anti-theft system Crash signal Right reversing light bulb, M17 Switch for heated rear window and exterior mirror on vehicles without air conditioner Central locking flashing (warning lamp switch)27 0 100 270 820 100 820 270 100 100 270 820K S42 10AMMMMS36 10A E41 E53 F2 F243 F241 V56 F131 V161 Z4 V17820270100S41 10AS 30A F10 F245 F132MMV115V163E52 3030305 6 7 K31Enable for electric window lifterE40E39 E55820Convenience locking, OPEN SKY roofSSP240_117K diagnosis connection31Heater/ACDesign and functionThe fully automatic air conditioner works along the same familiar principle as the one in the A4 and has been adapted to the centre console of the Audi A2. Sensors (condition detection) and actuators, together with the control unit, are responsible for automatic temperature and air flow regulation.SSP240_001In the Audi A2, three different bus systems operate at different transmission speeds. The control unit in the dash panel insert forms the interface (gateway) between the bus systems. The comfort databus continues to operate in emergency mode, even if one of the connections fails. A corresponding error message is stored in the fault memory. When the ignition is switched on, the operating and display unit E87 starts with the temperature, air distribution and fresh-air blower speed settings that were valid the last time the ignition was switched off with this key. Key identification is done by reading out the fixed transponder code. The immobiliser control unit, integrated into the dash panel insert, makes this information available to the operating and display unit E87, via the CAN bus.Depending on the vehicle equipment, different control units can be connected to the comfort system control unit via the data bus. J104 J217 J285 J537 E87 Control unit for ABS with EDL Automatic gearbox control unit Control unit with display in dash panel insert Control unit for 4LV (engine electronics) Operating and display unit for airconditioner54Air-conditionerDefroster flap positioning motor V107 Evaporator outlet temperature sender G263 Defrost flap Central flap Fresh-air intake temperature sensor G89Fresh-air flap Recirculated air flap positioning motor V113Fresh-air blower V2 Recirculated-air flapCentral flap positioning motor V70 Pollen filter insertFootwell flap SSP240_002 Heat exchanger and PTC additional heater Z35 Temperature flap positioning motor V68 Temperature flap Sender for footwell vent temperature G192 Distribution for dash panel ventThe air conditioner is a modular unit. Starting with a base unit, the other variants (i.e. semi or fully automatic control, additional heater, left or right-hand drive vehicles) can be created by adding additional components or swapping components.Centre vent temperature sender G191SSP240_043 55Heater/ACThe pollen filter is located in a housing insert between the fresh-air blower and the air distribution. It is accessible from the passenger compartment. After detaching the filter cover (push-fit components), the filter can be taken out from below. On vehicles without air conditioner, the series resistor for the fresh-air blower N24 can be removed after removing the glove box. After disconnecting the connector, the series resistor can be removed from the housing by twisting it to the left. Vehicles with air conditioners do not have a series resistor. The fresh-air blower is regulated by the fresh-air blower control unit J126. It can be renewed after first removing the glove box and the fresh-air blower.Series resistor for fresh-air blower N24SSP240_003 Pollen filterFilter cover Push-fit components 56Air distributionSSP240_007Air distribution in vehicle interiorFresh-air blower Windscreen vent Pollen filter Evaporator Dash panel vent Fresh-air Air flow flapFootwell vent Recirculated air flapsHeat exchanger SSP240_008 Electric additional heater (PTC additional heater, diesel engines only for non “cold countries”) 57Heater/ACFresh/recirculated air flaps The fresh-air/recirculated air flap is switched electrically by means of a positioning motor. Using a system of levers, both flaps are adjusted as a function of each other, depending on the driver’s requirements. In the “Defrost” position, the recirculated air switch is disabled electronically.Fresh-air flapFresh-airRecirculatedair flapBulkheadPassenger SSP240_127 Flaps – fresh-air position SSP240_009 Flaps – recirculated air positionThe heat exchanger is located at the bottom on the air distributor housing of the air conditioner. It is possible to remove the heat exchanger with the air conditioner still in position. The two coolant connections are held in place with two spring clips.Safety spring clip fastened.SSP240_004 58CompressorThe concept of the new compressor – single-side operating swash-plate compressor with 6 reciprocating pistons – variable displacement to match cooling requirements Distinctive features: – External control function by means of regulating valve N280 – Tubular piston – Belt pulley drive (no magnetic clutch) Belt drive: – The compressor continues to operate when the system is switched off. The delivery rate in this case is below 2 %. Operation The regulating valve for the air conditioner compressor, N280, is controlled steplessly by the air conditioner operating and display unit, E87. This brings about a change in the pressure conditions in the compressor housing. The slant of the swash plate changes and thereby determines the displacement. For compressor control, external conditions, i.e., the temperature required by the occupants, the weather and thermal load in the system, are evaluated. This task is done by the operating and display unit E87. It also evaluates a square-wave signal from the high-pressure sender, G65, that is dependent on the pressure in the refrigerant circuit. The pulse width –A- increases as pressure increases. A signal ratio is produced from the pulse width –A- and signal distance –B-; the signal ratio is processed in the operating and display unit E87, i.e. a high signal ratio equals a high cooling performance and vice versa. Depending on the various parameters that can have a regulating effect, the operating and display unit calculates a signal ratio as a setpoint selection for the flow of current to the regulating valve N280. The evaporator temperature at sender G265 is the reference signal for compressor control.An optical and acoustic check of the system is no longer possible on account of the fact that there is no longer a magnetic clutch.Measuring equipment DSO5 V/Div. = 5 ms/Div.Auto modePhotoAChannel AChannel BTrigger modeMeasuring mode0BTime/Div. Position MultimeterSkipPrintHelpSSP240_118 59Heater/ACCompressor at zero deliverySSP240_011The compressor displacement can be varied by the slant of the swash plate. If the air conditioner compressor is not working, the swash plate is vertical (the stroke of the pistons is less than 2 %). The swash plate is adjusted by the difference in pressures in the compressor. – Suction pressure Pressure on the low pressure side of the system or pressure of the refrigerant upstream of the compressor. – High pressure Pressure of the refrigerant after compression, main pressure for adjusting the swash plate towards full load.– Crankcase pressure Backpressure in the crankcase of the compressor together with the swash plate return spring towards0 fill. The regulating valve is responsible for balancing these differences in pressure; the regulating valve is exposed to all pressures. The high pressure and the crankcase pressure are the main influences on the equilibrium of forces resulting from the pressures. The high pressure acts on the piston in the compression chamber and tries to increase the slant of the swash plate = greater displacement. The crankcase pressure develops a force that wants to move the swash plate into a vertical position.60Compressor at full loadRegulating valve for air conditioner compressor, N280 Crankcase pressureCompression chamberTubular piston Swash plateHigh pressure Suction pressureDriver shaft Suction side Crankcase High-pressure side Return spring SSP240_012The electromagnetic regulating valve, N280, has a plunger and a pressure element. The suction pressure determines the position of the pressure element, and thereby the regulating travel of the plunger. If a higher cooling performance is required, the operating and display unit activates the regulating valve. This moves the plunger down and reduces the cross section of the join between the high pressure (dark green) and the crankcase pressure (yellow). This results in the high pressure becoming dominant; it then moves the swash plate to a slanting position by means of the piston.If a lower cooling performance is required, the cross section of the join (between high pressure and crankcase pressure) is increased. This causes the pressures in the compression chamber and the crankcase to balance out. This moves the swash plate towards a zero delivery position, with the help of the return spring. A signal ratio of 400 Hz enables the regulating valve, N280, to keep the push-rod in a “floating” state, thereby achieving optimum pressure regulation.61Heater/ACPulleyRubberDrive platePulleySSP240_040SSP240_013The pulley comprises a drive plate and a pulley. The two components are joined together in a frictional connection by 1 moulded rubber element. The rubber element with 4 recesses joins the pulley and the drive plate.62disabledSSP240_040SSP240_014If a hazardous situation occurs – compressor is disabled – the transmission forces between the drive plate and the pulley increase considerably in the area around the moulded rubber parts. The pulley pushes the rubber element in a rotating motion on to the disabled drive plate.The rubber element deforms at the 4 recesses. The pressure on the drive plate increases and deforms it until there is no connection between the pulley and the drive plate. This prevents damage to the single-belt drive.63Heater/ACAdditional heatersPTC additional heater Z35Heater heat exchangerHeating element for additional heater Z35Bottom se