TECHNICAL DOCUMENTATION

SSP 099 1.8 TFSI 132kW 2.0 TFSI 162kW EA888

PDFEN60 pages4 MB
SSP 099 1.8 TFSI 132kW 2.0 TFSI 162kW EA888 - PDF cover

This PDF is currently unavailable.

Read document text
Engines 1.8 l TFSI 132 kW, 2.0 l TFSI 162 kWEA888 design rangeProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Self-study ProgrammeŠKODAService®99 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Contents Engines 1.8 l TFSI, 2.0 l TFSI (EA888 design range)1. Introduction of the 1.8 TFSI / 132 kW Engine � � � � � � � � � � � � � � � � � � � � � � � � � � � 1.1 Engine Characteristics � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 1.2 Table of Engine Parameters � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 1.3 Engine Power Chart  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 2. Development Objectives of the New Engine Design  � � � � � � � � � � � � � � � � � � � � 2.1 Aggregate Modularity � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 2.2 EU6 Standard Compliant – Reduced Emissions of Solid Particles and CO2 � 2.3 Lower Fuel Consumption � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3. Engine Weight Reduction  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3.1 Engine Weight Reduction Measures  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4. Cylinder Block and Oil Sump � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4.1 Cylinder Block  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4.2 Oil Sump � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4.3 Cylinder Block and Oil Sump – Configuration  � � � � � � � � � � � � � � � � � � � � � � � � 5. Cylinder Head  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5.1 Cylinder Head – Configuration  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5.2 Integrated Exhaust Gas Ducts � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5.3 Integrated Exhaust Gas Ducts Cooling  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6. Crank Mechanism � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6.1 Piston  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6.2 Connecting Rods  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6.3 Crankshaft  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6.4 Crankshaft Mounting � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7. Chain Timing Mechanism of the 1.8 TFSI engine � � � � � � � � � � � � � � � � � � � � � � � � 7.1 Balancing Shafts of the Chain Timing Mechanism � � � � � � � � � � � � � � � � � � � � � 8. Fuel Injection  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8.1 The Basic Fuel Injection Principles and the Combined Injection Rationale � 8.2 Combined Fuel Injection System Design � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8.2.1 The FSI High-Pressure Fuel Injection System � � � � � � � � � � � � � � � � � � � � 8.2.2 The MPI Low-Pressure Fuel Injection System  � � � � � � � � � � � � � � � � � � � 8.3 Injection Modes in Dependence on Engine Load Type � � � � � � � � � � � � � � � � � 8.4 Fuel System Diagram � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9. Cooling System � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9.1 Coolant Pump and Engine Temperature Regulation Controller  � � � � � � � � � � 9.2 Engine Temperature Regulation Controller  � � � � � � � � � � � � � � � � � � � � � � � � � 9.3 Engine Temperature Regulation Controller Modes  � � � � � � � � � � � � � � � � � � � 10. Air Intake System with a Turbocharger  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10.1 System Diagram  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10.2 Intake Manifold Design � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10.3 Turbocharger  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 11. Crankcase Ventilation � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 11.1 Crankcase Ventilation Principle � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 11.2 Basic Description of the Crankcase Ventilation System  � � � � � � � � � � � � � � � 11.3 Coarse Oil Separation  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 11.4 Fine Oil Separation  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 11.5 Supply of Cleaned Gases to the Combustion Chamber � � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �5 5 6 7 8 8 8 8 9 9 10 � 10 � 10 � 11 � 12 � 13 � 15 � 16 � 17 � 18 � 18 � 18 � 19 20 � 21 22 22 23 24 24 25 26 27 27 28 30 33 33 35 37 39 39 40 � 41 � 41 42� � � � � � � � � �Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB3 12. Engine Lubrication  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12.1 Lubrication System Changes � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12.2 Holder of Auxiliary Aggregates with Oil Filter and Engine Oil Cooler  � 12.3 Engine Lubrication System � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12.4 Two-StageRegulation Oil Pump � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12.5 Oil Circuit Diagram � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12.6 Piston Cooling Nozzles � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12.6.1 Operating Mode with Disconnected Cooling Nozzles � � � � � � � � � 12.6.2 Operating Mode with Active Cooling Nozzles � � � � � � � � � � � � � � � 12.6.3 Piston Cooling Nozzles Operating Modes Chart � � � � � � � � � � � � � 12.6.4 Piston Cooling Nozzle System Monitoring Function � � � � � � � � � � 13. 2.0 l TFSI 162 kW Engine  ��������������������������������������� 13.1 Engine Characteristics � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 13.2 Comparison of the 2.0 l TFSI 162 kW and 1.8 TFSI 132 kW Engines � � � 13.3 Table of Engine Parameters � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 13.4 Engine Power Chart  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � �44 44 44 46 47 48 50 50 � 51 52 52 53 53 53 56 57You will find the instructions for assembly and disassembly, repairs, for diagnostics plus detailed user information in the VAS diagnostic instruments and in the on-board literature. Editorial closing date was in 8/2013. This Book is not subject to updating. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP95_004GB 1. Introduction of the 1.8 TFSI / 132 kW Engine1.1 Engine CharacteristicsNew engine's main characteristics: – cylinder head structure with an integrated exhaust pipe (turboblower weight reduction by 40 %) – combined direct (FSI) and indirect (MPI) injection (to limit formation of solid particulate) – two injectors per cylinder – variable timing of the intake and exhaust valves with a chain control gear – variable lift of exhaust valves – Intelligent cooling circuit – temperature control based on the engine load and RPM – One Lambda probe upstream of turboblower and another Lambda probe downstream catalytic converter – increase of injection pressure (FSI) to 200 bar – reduction of weight – turboblower controlled by an electric motorProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB5 1.2 Table of Engine ParametersEngine Parameters Design Ignition inline four-cylinder petrol engine, two top-mounted camshafts (2xOHC) with chain drive, turbocharged engine with intercooler, with combined fuel injection, mounted transversally at the front, Liquid-cooled aggregate 4 1798 cm3 82.5 mm 84.2 mm 132 kW at 5100–6200-1 250 Nm* at 1250–5000-1 9.6 : 1 electronically controlled combined fuel injection Continuous intake camshaft adjustment Continuous exhaust camshaft adjustment, The AVS system – of two-stage exhaust valve lift switching electronic ignition of pressure circulating type with a full-flow oil filter unleaded gasoline of min. oct. no. 95/91** EU6 134 kgNumber of cylinders Displacement Bore Stroke Max. power Max. torque Compression ratio Charging Intake valve control Exhaust valve control Ignition Lubrication Fuel Emission standard Engine weight* 280 Nm in connection with the 4x4 drive ** W  hen using gasoline of lower octane index, the power may be reduced slightly.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�6GB 1.3 Engine Power ChartThe engine features the maximum torque of 250 Nm, which is available thanks to its turbocharger and advanced valve equipment within a wide RPM interval. From 1,250 to 5,000 RPM-1. The engine version designed for the vehicles with all wheel drive, where rear axle is driven by the Haldex clutch, provides the maximum torque of 280 Nm at 1,350 - 4,500 RPM-1. It offers the same maximum output of 132 kW at 4,500 - 6,200 RPM-1. The performance characteristics is further adapted by the engine control unit software.400SP99_11140 360320120280 100 240 80 20016060120 40 80 20 40M (Nm)0100020003000400050006000n (min-1)P – power, M – torque, n – engine speedFront drive power curve - max. 132 kW 4x4 drive power curve - max. 132 kW Front drive torque curve - max. 250 Nm 4x4 drive torque - max. 280 Nm or commercial purposes, in part or in whole, is not permitted Protected bycurve copyright. Copying for privateunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GBP (kW)7 2. Development Objectives of the New Engine Design2.1 Aggregate ModularityThe third generation of the 1.8 TFSI, EA888 series engine has been designed in line with the VW group's modular concept strategy. The dimensions, mounting and connecting points of the 3rd generation of the EA888 engine design series have been designed in a way, thanks to which the engine may be used as a "global aggregate" with transverse mounting (MQB*) and longitudinal mounting (MLB**). The transverse mounting features an engine bearer and oil dipstick. If the engine is mounted longitudinally, engine brackets and a cap instead of the oil dipstick will be used. These mounting options enable installation of this engine series within the whole VW group.2.2 EU6 Standard Compliant - – Reduced Emissions of Solid Particles and CO2The new aggregate has not only been developed because of adoption of the modular strategy by the VW group, which is applied to all vehicle parts, including aggregates. The aggregate was also developed due to the application of more stringent exhaust gas standards (EU 6 standard), and also to reduce fuel consumption and CO emissions2. That is why the engine has been completely redesigned from all perspectives. The following items were key during the new engine development: – Engine design, featuring the maximum number of parts identical to all the engine versions – Engine weight reduction – Reduced engine internal friction – Increased engine output and torque at reduced fuel consumption – Improved aggregate comfort qualities2.3 Lower Fuel ConsumptionDownsizing The turbocharging of petrol engines resulted in smaller and lighter aggregates, as required. Downspeeding During the design of the third generation of the EA888 engines, the requirement was to develop an aggregate with even a greater torque interval in order to shift the engine operation to lower RPM. The designers responded to this requirement primarily by focusing development efforts on valves: a) Variable valve timing – Intake camshaft adjuster – Exhaust camshaft adjuster development b) Exhaust valves two-stage lift switching c) Engine timing chain friction optimization The measures applied in both groups reduce fuel consumption.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�* MQB – Modularer Querbaukasten ** MLB – Modularer Längsbaukasten8GB 3. Engine Weight ReductionThe weight of the new 1.8 TFSI EA888 series 3rd generation engine decreased by 7.8 kg thanks to the weight reduction of the following engine components.3.1 Engine Weight Reduction Measures– Thin cylinder block wall – Absence of external oil separator, the coarse oil separator labyrinth is integrated in the new engine directly in its cylinder block – Lighter cylinder head with integrated exhaust piping and connected turbocharger – Lighter crankshaft with its four counterbalances in smaller diameter bearings – Oil sump upper section of aluminium pressure casting – Plastic oil sump bottom part – Aluminium bolts in the whole engine – Balancing shafts partially supported in needle bearingsProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB9 4. Cylinder Block and Oil Sump4.1 Cylinder BlockWeight has been reduced: Most weight reduction has been achieved on the cylinder block. The cylinder block wall thickness has been reduced from 3.5 mm to 3.0 mm. The coarse oil separator has been integrated into the cylinder block. As a result, the cylinder block weight decreased, compared to the 2nd generation engine, by a total of 2.4 kg. Internal friction has been reduced: The crankshaft primary bearings are of a smaller diameter. The balancing shafts have been partially supported by means of needle bearings. Additional changes, compared to the 2nd generation engine: – Changed cross-section of the coolant return line – The oil radiator is fed via the cylinder block coolant return line – Knocking sensor optimized positionCylinder block sealed using a liquid sealant The engine side cover is sealed by a liquid sealant. The flange is mounted to the cylinder block by aluminium bolts. Liquid sealant has been applied to the timing mechanism cover as well.4.2 Oil SumpOil sump top section It is made of an aluminium pressure casting. An oil pump is bolted in it and a honeycomb insert for oil suction and return flow. The oil sump top section also features pressure oil lines and the two-stage oil pump control valve. It is sealed to the cylinder block by a liquid sealant and mounted by aluminium bolts. The main bearings covers are bolted to the oil sump top section in order to further improve the aggregate's acoustic qualities. Oil sump bottom part The oil sump bottom part is made of plastic. It has saved about 0.1 kg of weight. It is sealed by a die-formed rubber gasket and mounted by steel bolts. The oil sump bottom part features the G266 oil level and temperature sensor. The oil drainage bolt is also made of plastic (bayonet joint).Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�10GB 4.3 Cylinder Block and Oil Sump –- ConfigurationTiming mechanism coverCylinder block Sealing flange on the engine drive sideSump top sectionHoneycomb insert Gasket Oil pumpSP99_43Oil sump bottom partDrain bolt Oil quality, temperature, and level sensorProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB11 5. Cylinder HeadThe cylinder head has been completely redesigned, compared to the previous engine generation. Among turbocharged engines, this is the first engine, featuring exhaust gas cooling using a special cooling line directly integrated into the cylinder head. Additional cylinder head design changes: – Extended spark plug thread – New ignition modules – Optimized weight camshafts – Reduced elasticity of the timing mechanism – The G62 coolant temperature sensor installed in the cylinder head – High-pressure pump in a new position – Turbocharger turbine casing directly attached to the cylinder block – Optimized intake ducts – Flexible separation of injection valves from the cylinder headIgnition module 1–4 with their terminal power stage The exhaust camshaft with the AVS systemExhaust cams lift adjusters 1–8Integrated cooling pipingCamshaft adjuster for intake valvesIntegrated turbocharger Integrated piping (leads cooling piping exhaust gases to the Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by Š KODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability turbocharger)with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP99_11Camshaft adjuster for exhaust valves12GB 5.1 Cylinder Head –- ConfigurationCylinder head cover Hall sensorIntake valve camshaft Exhaust cams lift adjusters 1–8 Valve lifterIntake valve camshaft adjusterExhaust valve camshaftValve rockerIntake valves exhaust valves Exhaust valve camshaft adjusterHall sensor Coolant-temperature sensor Duct dividing platescylinder headAnti-freeze unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� protective capProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedSP99_10Anti-freeze protective capDistance bolt of the integrated exhaust gas collectorCylinder head threelayer metal gasketGB13 AVS Exhaust Valve System The exhaust valve camshaft features two-stage valve lift switching. The lift switching system optimizes valve operation at various engine loads.Exhaust gas valve camshaft adjuster In addition to the two-stage valve switching, the camshaft also features a shaft adjuster. Those two adjusting systems help to achieve the maximum play levels when engine load changes. That results into faster torque increase and lower fuel consumption.Sealing The cylinder head cover is attached by steel bolts and sealed by a liquid sealant. The sealing between the head and the engine block is provided by a three-layer metal gasket. On the camshaft adjuster side, the engines are sealed by a plastic chain cover.During cylinder head disassembly, it is necessary to remove the cylinder head cover first.14Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB 5.2 Integrated Exhaust Gas DuctsThe exhaust gas ducts are now integrated in the cylinder head. Use of these integrated exhaust ducts significantly reduces the temperature upstream of the turbine, compared to the regular routing. In addition, a turbocharger resistant to high temperature is used. The integrated exhaust gas collector transfers its thermal energy to the coolant, which helps the engine reach its operating temperature faster. Exhaust Gas Ducts The exhaust gas ducts are designed in such a way that the exhaust gas flow leaving the cylinder does not interfere with the flushing of another cylinder. The exhaust ducts from cylinders 1 and 4 and 2 and 3 meet at the flange, which connects the turbocharger to the cylinder head. The total flow energy from all the cylinders is then available to drive the turbocharger turbine.Cylinder headProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP99_42Exhaust gas ductsTurbochargerGB15 5.3 Integrated Exhaust Gas Ducts CoolingThe integrated exhaust gas collector supports quick coolant heating; therefore, it is a critical component of the engine's effective heat management. After cold engine start-up, heat transfers from the exhaust gas collector to the coolant within a very short period. This heat directly heats the engine and car interior. Thanks to this integration, heat is effectively transferred within the engine. The Lambda probe, exhaust gas turbocharger, and catalytic converter reach their optimum operating temperature quicker. The short engine heating phase is followed by its cooling phase. Otherwise, coolant within the exhaust gas collector would quickly start boiling. For this reason, a coolant temperature sensor is installed at the cylinder head's hottest spot.Cooling duct top sectionExhaust gas duct from cylinders 1 and 4The main water cooling ductExhaust gas duct from cylinders 2 and 3 Cooling duct bottom partSP99_12Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�16GB 6. Crank MechanismThe crank mechanism for the 3rd generation of the EA888 series engines was designed to reduce weight and friction.Piston Piston pin securing ringThe piston bottom features a specifically shaped depression, which directs the intake air flow towards the spark plug during direct layered injection.Gudgeon pinConnecting rodConnecting rod bearing top shellSP99_03Balancing counterweightConnecting rod bearing bottom shellCrankshaftPiston rod bearing coverProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB17 6.1 PistonCompared to the previous generation, the piston features increased play in order to reduce engine friction. The piston skirt features special wear-resistant coating. Three piston rings seal the piston inside the cylinder.Grooved center piston L-ring Top tapered piston ring Two-piece wiping ringSP99_056.2 Connecting RodsThe whole engine exclusively features lead-free bearings. In the crank mechanism assembly, it applies to both the crankshaft main bearings and the connecting rod bottom eye bearings. Compared to the previous generation, there is no bronze bushing in the top connecting rod eye. The gudgeon pin features a special surface coating, and it runs directly through the steel connecting rod and the piston made of aluminium alloy.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability bushing with respect to the correctness of information inBronze this document. Copyright by ŠKODA AUTO A. S.�absenceSP99_066.3 CrankshaftCompared to the second generation, the crankshaft bearings have been downsized from 52 mm to 48 mm. The bearings are two-layer lead-free bearings.18GB 6.4 Crankshaft MountingIn addition to the attachment of the main crankshaft bearing cover to the cylinder block, the cover is also rigidly attached by bolts mounted to the oil sump top section. This design feature reduced the aggregate's vibrations and noise.Cylinder blockBearing cover boltSP99_04Side boltBearing cover bottom bolt Sump top sectionProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB19 7. Chain Timing Mechanism of the 1.8 TFSI EngineThe basic chain timing mechanism design does not differ from the previous engine generations. However, even the chain timing mechanism has been subject to thorough development. Due to reduced friction and lower oil consumption during engine lubrication, it was possible to reduce the power consumption of the timing mechanism. The chain tensioners have been modified to accommodate lower oil pressure in the system.Intake valve camshaft adjuster Exhaust valve camshaft adjusterHigh-pressure fuel pumpThe exhaust camshaft with the AVSTiming chainCoolant pumpSP99_07Balancing shaft needle bearingProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Controllable oil pump20GB 7.1 Balancing Shafts of the Chain Timing MechanismThe balancing shafts' weight has been reduced. The shafts are partially supported by needle bearings now. This design feature significantly minimized chain assembly friction.Outer bearing ringToothed chain Needle bearings cageNeedle bearingSP99_08Idle gearTensioning line Crankshaft sprocketSkid barReduced friction load of the timing mechanism has positive effect on the Start-Stop mode. Reduced friction also means reduced heat transfer in the system; therefore, lower oil operating temperature.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB21 8. Fuel Injection8.1 The Basic Fuel Injection Principles and the Combined Injection RationaleWhile diesel engines with direct injection are characteristic with low CO emissions,2 , they still produce large emissions of solid particles. Gasoline engines with direct injection may even produce more soot than comparable diesel aggregates. That is why the 1.8 TFSI engine design features a dual injection system in order to reduce emissions. The engine control unit activates one or the other injection system in order to effectively reduce the amount of solid particles and CO2. The engines combines direct injection with multi-point indirect injection: –F  SI direct injection (Fuel Stratified Injection) High-pressure system, in which the injection valve is directed right into the combustion chamber. Intake air throttle valve Air supplyHigh-pressure fuel supplyThe injection valves are directed right into the combustion chamberSP99_03unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability –M  PI indirect multi-point injection (Multi Point Injection) with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Low-pressure system, in which the injection valve is directed to the subject cylinder's intake duct. It injects fuel upstream the cylinder intake valve.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedFuel supply to a low-pressure railThe valves inject fuel into the intake ducts upstream the subject cylinders' intake valvesSP99_0422GB 8.2 Combined Fuel Injection System DesignUse of the combined injection in the new engine design brought the following benefits: – FSI injection system pressure increased to 200 bar (new high-pressure system design) – Reduced engine noise (separation of the FSI injection valves from the cylinder head through flexible washers) – Compliance with Euro 6 emission standard, reduced amount of solid particles and CO2 (fuel injection split between the MPI system and the FSI system, based on the engine's torque characteristics) – MPI precise injection into the compartment upstream the intake valve (suction duct modification and MPI injection valves installation) – Reduced consumption at partial engine load (MPI injection mode application)Fuel pump control valveLow-pressure fuel rail MPI rail pressure sensor MPI injection valveHigh-pressure fuel pumpIntake air temperature sensor with pressure sensor in the intake manifoldSP99_01Intake valve throttle valve FSI injection valve High-pressure fuel railMPI low-pressure injection system FSI high-pressure injection systemProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB23 8.2.1 The FSI High-Pressure Fuel Injection SystemThe system pressure has been increased to 200 bar; therefore, all the high-pressure system components have been modified. The valves are newly mounted by steel shims. That has reduced acoustic surges during injection. Those surges used to hit the cylinder head before. The high-pressure rail is newly attached to the cylinder head and not to the intake, as before. The high-pressure injection valves have been moved backwards (away from the engine head). That improved mixture homogenization and also reduced valve thermal load. High-Pressure Pump Cooling The high-pressure pump is cooled. The coolant is fuel, which supplies the MPI low-pressure rail and flows through it. As a result, even during the MPI regime, the pump is automatically flushed with fuel; therefore, cooled. To minimize pulsations transmitted from the high-pressure pump into the MPI fuel supply, a throttle valve is fitted in the supply line.8.2.2 The MPI Low-Pressure Fuel Injection SystemThe MPI system features its own pressure sensor located in the MPI rail. Both the rail and the intake manifold are made of plastic. The MPI injection valves are integrated into the intake manifold, so the injected fuel beams are perfectly centered in the compartment upstream the intake valves.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�If the engine has run in the MPI mode for a longer period of time, the FSI injection mode is briefly activated in order to avoid fuel carbonization in the FSI high-pressure injection valves.24GB 8.3 Injection Modes in Dependence on Engine Load TypeThe SP99_02 diagram on this page displays the areas of the MPI or FSI injection modes for each particular operating point defined by particular combination of engine speed and load. The number and mode of the individual injections (MPI or FSI) are subject to thermodynamic optimization in order to minimize soot emissions.Simple FSI injectionEngine torque (Nm)Double FSI injectionSimple MPI injectionEngine speed (min)-1)SP99_02Engine mode: Engine start Cold engine (cooling liquid temperature below 45 °C) Warm engine operationInjection mode FSI Triple direct injection (three times during the compression stroke) FSI Simple direct injection (once into the intake stroke) FSI Double direct injection (one into the intake stroke and one into the compression stroke) MPI Simple injection FSI Double direct injection (one into the intake stroke and one into the compression stroke)Warm engine (cooling liquid temperature above 45 °C) – partial engine load Warm engine (cooling liquid temperature above 45 °C) – Higher engine loadIf one of the fuel injection systems fails, the other system will take over in the emergency operating mode. That ensures that the vehicle will for remain operational. Protected by copyright. Copying private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB25 8.4 Fuel System DiagramFuel filterFuel pump G6Fuel pump control unit J538Fuel pump control valveLow-pressure rail fuel pressure sensorHigh-pressure fuel pumpMPI injection valves for cylinders 1–4SP99_58High-pressure rail fuelProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted pressure sensor unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�FSI injection valves for cylinders 1–426GB 9. Cooling SystemModernized ITM temperature management*During the 1.8 TFSI engine development, the whole cooling system was redesigned. The designers primarily strove to achieve quick engine heating, fuel consumption reduction through quick and thermodynamically optimal engine temperature regulation, including potential interior heating. The modernized temperature control of the 1.8 TFSI engine is based on two key components. The first one is the exhaust gas collector integrated in the cylinder head, the other one is the rotational valve module/N493, which controls the engine temperature.9.1 Coolant Pump and Engine Temperature Regulation ControllerCoolant pump The discharge of the water circuit towards the radiator, heating system, gear box radiator**Rotary slide valve No. 2Toothed belt dtive wheel Rotary slide valve No. 1Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Toothed for coolant drive The return line of interior heating. turbocharger cooling, and gear box coolingRadiator return lineSP99_14Coolant pump drive sprocket LidThe N493 rotational valve module, which regulates engine temperature, forms one assembly with the coolant pump. It is located on the engine's cold side. * intelligent thermal management ** for automatic transmission for 4 x 4 vehiclesGB27 9.2 Engine Temperature Regulation ControllerThe rotary engine temperature controller N493 controls coolant flow by the two mechanically connected rotational valves. The subject valve position directs or completely stops the flow into the individual cooling system components. The control unit uses the valve system to effectively control the engine temperature modes. The rotational valves are actuated by a DC motor, which is controlled by signals from the control unit.Radiator piping connecting flange Oil cooler socketRotary slide valves actuator motor Rotary slide valve No. 2Sprocket, IdlerSP99_15Rotary slide valve No. 1Rotary slide valve shaft No. 1ThermostatProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Rotary slide valve boxThe radiator return line socket28GB The DC motor drives valve No. 1 through a worm gearing. The electric motor is controlled by the engine control unit 12 V signal of 1 Hz frequency. PWM digital signal is used. The rotational valve module controls the flow of coolant to the oil cooler, the cylinder head, and the main water radiator. The valve module does not regulate the gear box radiator, turbocharger, or interior heating. Valves No. 1 and 2 are mechanically connected. Rotating valve No. 1 opens valve No. 2 at a specific working angle. Valve No. 2 then closes at another angle. Rotational valve No. 2 opens the cylinder block cooling line. – Valve No. 2 starts opening when valve No. 1 turns by the 145°. – Valve No. 2 starts closing when valve No. 1 turns by additional 85°. At this point, valve No. 2 reaches the maximum opening of the cylinder block cooling circuit. The warmer the engine is, the more the rotational valves turn. The mechanical stoppers limit the end positions of the rotational valves.Cylinder block coolant outlet Cylinder head return coolant inletRotary valve No. 2Direct current electric motorThe supply for the radiator, heating, and gear box radiator Coolant pumpOil radiator return lineSP99_16Worm gearThe return line of interior Rotary heating. turbocharger valve No. 1 Protected by copyright. Copying for private or commercial purposes, in part orand in whole, is not permitted cooling, gear box coolingunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Radiator coolant return lineGB29 9.3 Engine Temperature Regulation Controller ModesThe following text describes the individual water circuit operating modes triggered by the engine temperature controller during engine heating.Cold-Engine Quick Warm Up Mode During cold engine heating, valve No. 1 is set to the angle of 160°. In that position, valve No. 1 closes the engine oil cooler inlets and the main water radiator return line. Rotational valve No. 2 closes the cylinder block supply. The Climatronic shut-off valve and the gearbox cooling valve are closed. The auxiliary coolant pump is off. As a result, no coolant circulates in the cylinder block. Based on load and RPM, the non-circulating coolant in the cylinder block is thus quickly heated up to the temperature of 90 °C.SP99_17Passenger Space Quick Warm Up Mode If it is required to heat the interior, the Climatronic Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted authorised shut-off valve and the auxiliary coolantunless pump are by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� activated. As a result, the coolant flows through the cylinder head, turbocharger, and the heat-exchanger that heats the car interior.SP99_19Minimum Flow-Rate Mode for Cylinder Head Protection The purpose of this feature is to protect the cylinder head and turbocharger from overheating. If it becomes necessary to quickly cool down the cylinder head or turbocharger after abrupt engine heating in the quick heat-up mode without coolant circulation, rotational slide valve is set to the angle of 145 °. Once that angle is reached, the permanent gear between the valves engages with the rotational valve No. 2 and opens it up. A small amount of coolant will immediately start flowing into the cylinder head, turbocharger, and rotational valve module and back to the coolant pump. The remaining coolant will proceed through the shut-off valve to the interior heat exchanger if needed.SP99_2030GB Engine Oil Cooler Socket Later during the heating phase process, the engine oil cooler inlet valve opens. Rotational valve No. 1 is set to the 120° angle. Simultaneously, rotational valve No. 2 opens, and the coolant flow through the cylinder block intensifies. By intentional supply of hot coolant to the oil cooler, the engine oil temperature starts increasing.SP99_17Gear Oil Heating Once the aggregate is sufficiently heated, the automatic transmission coolant valve finally opens in order to deliver excess heat to the gear box oil. The gear box oil heating starts once the coolant reaches the temperature of 80 °C without heating or 97 °C with heating.SP99_18Temperature control by the main water radiator At low RPM and minimum load, the coolant temperature is set to 107 °C in order to minimize engine friction. Under increased load and RPM, the coolant temperature is reduced to 85 °C. Rotational valve No. 1 is set in the angle range of 80° 0°, as needed. Once rotational valve No. 1 reaches the angle of 0°, the water return line to the water radiator becomes fully open.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP99_19GB31 Aftercooling Mode after Engine Shutdown If needed after engine shutdown, the aftercooling function becomes activated. Its purpose is to avoid coolant boiling in the cylinder head and turbocharger, or unnecessary engine cooling. The function may only become active 15 minutes after engine shutdown. During aftercooling, the rotational valve is set within the range of 160 - – 255°; the coolant temperature regulation remains active even in this mode. If intensive aftercooling and low coolant temperature are required, the water radiator return line will open; however, rotational valve No. 2 will close the cylinder block supply piping. Simultaneously with that, the auxiliary coolant pump and coolant shut-off valve are activated. Now, the coolant is flowing in two directions - through the cylinder head to the coolant pump and the turbocharger, rotational valve No. 1, and water radiator back to the auxiliary coolant pump. This feature significantly shortens the aftercooling period without any excess heat loss.SP99_18Engine Temperature Controller Failure If the angle sensor fails, the rotational valve is fully activated (maximum engine cooling). If the DC motor is defective or the rotational valve is stuck, engine RPM and torque become limited, based on the rotational valve's position. If the temperature inside the controller exceeds 113 °C, the thermostat will open the bypass valve to the water radiator in order to letfor all the or coolant flow through it.or in whole, is not permitted Protected by copyright. Copying private commercial purposes, in part unless fails, authorised ŠKODA AUTO A. S. ŠKODA AUTO A.without S. does notany guarantee or accept any liability If the regulator theby vehicle may continue driving engine damage risk.with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�System malfunction visualization: – The instrument cluster display will display a maximum engine RPM limitation notification – The displayed notification is accompanied by sound annunciation and EPC failure indicator activation – Actual coolant temperature indication on the instrument cluster32GB 10. Air Intake System with a Turbocharger10.1 System DiagramTurbochargerAir filterExhaust gas flowFresh air flowBypass valveThe waste gate adjusterTurbocharger circulation valveCharge-air coolerCharge pressure sensorSP99_25Intake Throttle Protected by copyright. is not permitted Intake air Copying for private or commercial purposes, in part or in whole, manifold flapsunless control unit authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Intake Flaps temperature potentiometer with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� sensor with pressure sensorIntake flaps control valveExhaust manifold Intake air Charge air Circulating airThe air filter removes mechanical impurities from the intake air. The air proceeds through the low-pressure section to the compressor blades. The compressor is powered by the exhaust gas turbine. Then, the air proceeds through the high-pressure section. The air cooler is installed upstream the main intake throttle. Cooling decreases the air molecules volume and mixture explosiveness in the combustion chamber. Which, in the case of a gasoline engine, might cause undesirable self-ignition Then, the already cooled and compressed air proceeds to the individual intakes of the subject cylinders.GB33 TurbochargerTurbocharger circulation valve Air filterIntake flaps control valveWaste gate adjusterCompressedair intercoolerContactless angular sensorCompressed air temperature / pressure sensorThrottle bodySP99_36Intake manifoldCompressed-air radiatorProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Charge pressure sensorThe turbocharger is driven by the exhaust-gas powered turbine. The engine water lines decrease the exhaust gas temperature as they are flushing integrated exhaust gas ducts. As a result, the turbocharger thermal load decreases.34GB 10.2 Intake Manifold DesignFuel pump control valveHigh-pressure fuel Vacuum controller pump of the intake manifold flapsCharge air temperature and pressure sensorMPI injection valvesSP99_26AIntake manifold flapsFSI injection valvesIntake Manifold – Principle Due to the increased charge pressures, the throttle flaps system of the intake manifold has been redesigned. The one-piece stainless steel cranked shaft guarantees the maximum torsional rigidity while controlling the flaps in the intake ducts of the individual cylinders. A contactless angular sensor is used to detect the flaps angle.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB35 When open flaps match the intake duct shape. The flaps are electro-pneumatically controlled. The control unit controls the intake flaps control valve, which controls the vacuum actuator of the intake flaps.Contactless angular sensor Throttle bodyProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Intake flaps control valveSP99_26BFSI injection valves36GB 10.3 TurbochargerCharging the engine using a turbocharger enables the engine to deliver maximum torque within a wide RPM range and improves the engine parameters under its full load. The two cylinder head outlet exhaust gas ducts only join behind the turbocharger flange; therefore, shortly prior to the turbine. As a result, the exhausts from the individual cylinders are separated as much as possible. The new turbocharger has the following features: – Electric waste gate controller –Lambda probe upstream of turbine – Compact turbine casing with dual inlet, mounted directly to the cylinder head – Compressor casing with integrated exhaust pulsation absorber and electrically controlled circulation valve – Turbine wheel resistant to temperatures up to 980 °C – Bearing shell with oil and coolant supply lines – Milled compressor wheel for better RPM stability and reduced noiseElectrically controlled circulation valveProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Integrated pulsation absorberSP99_45Waste gate valveCylinder head two-duct inlet flangeElectric waste gate controllerGB37 Turbocharger Internal DesignElectrically controlled circulation valveCompressor wheel Compressor casingTurbine wheelSP99_46Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Waste gate unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Turbine casingadjuster38GB 11. Crankcase Ventilation11.1 Crankcase Ventilation PrincipleA small amount of gas leaks from the combustion chamber around the pistons into the crankcase. It is necessary to bring those gases back to the intake. In order to comply with applicable emission standards, before combusting this gas, it has to be perfectly freed of oil.Fine oil separator moduleTurbocharger gas inlet (for the charging mode)Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Fine oil separator ductGases flowing into the intake manifold (for the intake mode)Return line from the oil separatorCoarse oil separator Oil return line from the coarse oil separatorSP99_27Duct to the shut-off valve in the oil sump (valve detail - see figure SP99_29)Contaminated Polluted gas flow direction Separated oil streaming directionGB39 11.2 Crankcase Ventilation SystemThe 1.8 TFSI engine features a crankcase venting system of a modern design. The designers strove to minimize the number of design components. All the components, except for the cleaned gas outlet piping, are integrated in the engine. The system features the following components: – Coarse oil separator integrated in the cylinder block – Fine oil separator screwed into the cylinder head cover – Cleaned gas outlet duct – Contaminated gas duct out of the cylinder block, featuring a shut-off valve in the oil sump honeycomb insertSP99_28In the intake mode, the gas leaving the fine oil separator, proceeds to the intake manifold.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP99_29The shut-off valve of the contaminated gas duct leading to the fine oil separator. The shut-off valve prevents the intake of oil from the oil sump into the piping, for example, during unfavourable pressure conditions.40GB 11.3 Coarse Oil SeparationThe coarse oil separator is based on a labyrinth, through which air with oil from the crankcase are exhausted. Due to the air direction changes in the labyrinth, oil particles separate, and proceed through the oil return line in the cylinder block back into the oil sump. The return line only ends under the oil sump oil surface.11.4 Fine Oil SeparationContaminated gases flow through the cylinder head into the fine oil separator. Then, they are first cleaned in the cyclonic separator. Separated oil proceeds from the fine oil separator through a separate line in the cylinder block back to the oil sump. A single-stage pressure control valve brings the cleaned air back to the cylinders.Connection to the active carbon container The bypass valve, which opens high flow rates (high engine RPM), high flow speed also causes oil separation Pressure control valveProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP99_30Fine oil separator return line back to the oil sumpCleaned air line leading to the turbochargerCyclone separatorGB41 11.5 Supply of Cleaned Gases to the Combustion ChamberUpon fine separation and passing through the pressure control valve, the cleaned air proceeds to the cylinders. Automatic check-valves integrated in the fine oil separator module provide automatic air flow regulation. Upon engine shutdown, the check-valves snap back into their basic positions. The check-valve is open in th