TECHNICAL DOCUMENTATION

SSP 069 3.6 ltr 191kW FSI

PDFEN52 pages2 MB
SSP 069 3.6 ltr 191kW FSI - PDF cover

This PDF is currently unavailable.

Read document text
Service3.6 ltr./191 kW FSI petrol engine69Self-study programmeermitted y liability A. S.� In the ŠkodaSuperb belongs to the VR family of engines based on its design. Compared to a traditional V-engine, a compact and space saving design is obtained through its reduced cylinder bank angle. This design enables to insert the engine crosswise in the vehicle.The VR engines distinguish themselves by their compactness for a wide range of applications.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP69_792GB ContentsIntroduction Engine mechanical components The cylinder block The crank assembly The cylinder head The camshaft adjustment The internal exhaust gas recirculation The crankcase ventilation The intake manifold The chain drive The vacuum pump The V-ribbed belt drive The oil circulation system The cooling circuit The exhaust system The fuel system The high-pressure fuel pump The injection valves Engine management The sensors The actuators The control units in the CAN data bus Function diagram 4 6 6 8 9 10 11 12 14 15 16 17 18 21 23 24 26 27 28 30 40 45 46For the instructions concerning the installation, removal, repair, diagnosis as well as the detailed user information, please refer to the ELSA system, the diagnosis unit VAS 505x and the onboard literature. The time for going to press was on the 11/2008. This brochure is not subject to the update.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB3 IntroductionTechnical highlightsThe 3.6 ltr. FSI engine, which is offered in the Škoda vehicles, is the latest representative of the VR engine series. The engine has improved performance parameters and a dynamic torque course due to it large displacement combined with the conversion to the FSI direct injection. The current emission standard EU4 plus can be fulfilled at the same time by using the FSI direct injection technology.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP69_04Special features- FSI direct injection - Four-valve technology with roller rocker arm - Weight-reduced cylinder block made out of cast iron - Two-part plastic intake manifold with optimized geometry of the inlet ducts - Oil pump with chain drive integrated in the cylinder block - Variable adjustment of inlet and outlet camshafts - Internal exhaust gas recirculation - High-pressure fuel pump drive and vaccum pump drive integrated in the cylinder head.4GB Technical data Engine code letters Design Number of cylinders Valves per cylinder Displacement in cm3 Bore Stroke V-angle Compression ratio max. power output max. torque Engine management Fuel Exhaust after treatment CDVA VR engine 6 4 3597 cm3 89 mm 96.4 mm 10,6° 11,4 : 1 191 kW at 6000 rpm-1 350 Nm at 2500 - 5000 rpm-1 Bosch Motronic MED 9.1 Super Unleaded with RON 98 or 95 – low reduction in performance 2 three-way catalytic converters; 2 linear lambda probes before catalytic converter and 2 snap-action lambda probes after catalytic converter EU4 plusEmission standard Torque and power output diagram190 180 170 160 150 140 130 120 P (kW) 110 100 90 80 70 60475 450 325 400 375 350 325 300 M (Nm) 275 250 225 200 175 150010002000 3000 4000 5000 6000 7000Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability n (min-1) with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP69_01GB5 Engine mechanical componentsThe cylinder blockSP69_02The cylinder block of the 3.6 ltr. FSI engine is made out of cast iron with flake graphite. This guarantees a high stability and firmness against high pressure, which arises during the combustion.The oil pump is integrated in the cylinder block.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�6GB V-angle 10,6° Cylinder longitudinal axisProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP69_0322 mm OffsetCrankshaft central axisV-angleThe offsetThe V-angle of the cylinder block is only 10.6° and therefore enables a compact design of the engine.The offset is the distance of the cylinder longitudinal axis to the crankshaft central axis. On the 3.6 ltr. FSI engine, the offset is 22 mm.GB7 Engine mechanical componentsThe crank assemblyRunning-in layerPiston recessSP69_05The pistons The pistons are diecasted from aluminium alloy. In order to improve the running-in characteristics, the piston skirt has a running-in layer made out of graphite. The piston crowns have combustion bowls. Due to the position and the shape of the piston recesses, the drawn-in air is swirled and through this a good mixture preparation is ensured. The pistons for the cylinder banks 1 and 2 differ in the arrangement of the valve pockets and the combustion bowls.The conrods On the 3.6 ltr. FSI engine the conrods are not cracked, instead they are cut. The conrod eye is designed in a trapezoidal shape. This shape enables a better distribution of the forces which are applied. The conrod bearing shells are coated with molybdenum. This results in good running-in characteristics and a high mechanical strength.The crankshaft On the 3.6 ltr. FSI engine, the crankshaft is casted from cast iron and is sevenfold stored.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�8GB The cylinder headInjection valves, cylinders 1, 3, 5SP69_07Injection valves, cylinders 2, 4, 6SP69_06Fitting position fuel highpressure pumpSP69_08Fitting position vacuum pumpunless authorised by is ŠKODA AUTO A. S. Š KODA AUTO S. does not guarantee or accept any liability On the 3.6 ltr. FSI engine, the cylinder head The holes forA. the injection valves of the cylinders with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� made out of an aluminium-silicon-copper alloy. 1, 3 and 5 are located above the intake manifold flange. The chain drive and the fixed attachment of the The injection valves of the cylinders 2, 4 and 6 fuel high-pressure pump as well as the vacuum are inserted into the holes below the intake manipump are located in the cylinder head. fold flange.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedThe injection valves for both cylinder banks are located on the suction side of the cylinder head.On the basis of various installation positions, two injectors of different lengths are used.GB9 Engine mechanical componentsThe camshaft adjustmentWing cell adjuster of inlet camshaft Wing cell adjuster of outlet camshaftSP69_09N318 camshaft adjustment valve 1 in the outlet N205 camshaft adjustment valve 1Depending on the load behaviour of the engine, an increase of the power output and the torque including fuel economy as well as a reduction of the exhaust emissions are achieved through the adjustment of the camshafts. The adjustment of the camshafts is carried out via two wing cell adjusters. Both camshafts can be adjusted in the direction of early opening and late opening of the valves.Maximum adjustment of the camshafts: - Inlet camshaft of 52 crank angle degrees - Outlet camshaft of 42 crank angle degrees Both camshaft adjusters are moved via two camshaft adjustment valves using the engine oil pressure.The adjustment of both camshafts enables a Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted maximum valve overlap of 42 crank angle deunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability In order to adjust the camshafts, the withsolenoid respect to the correctnessgrees. of information in this document. Copyright by ŠKODA AUTO A. S.� valves are actuated by the engine control unit: An internal exhaust gas recirculation is carried - N205 camshaft adjustment valve 1 out through the valve overlap. - N318 camshaft adjustment valve 1 in the outlet10GB The internal exhaust gas recirculationIntake manifold vacuum Outlet valve Inlet valve Inlet valve opens TDC Valve overlap Outlet valve closesStroke 4 Stroke 2SP69_10BDCStroke 1 Stroke 3The formation of nitric oxides NOx is counteracted through the internal exhaust gas recirculation. Just as for the external exhaust gas recirculation, the reduced formation of NOx is based on the combustion temperature being lowered by the recirculation of the combustion gases.It functions as follows During the discharge stroke, the inlet and outlet valves are opened simultaniously. In such a way, part of the combustion gases is suctioned out of the combustion chamber and again into the inlet duct. During the following suction stroke, these combustion gases are led into the combustion chamber together with fresh air.Nitrogen oxides are only formed in greater Advantages of the internal exhaust gas recirculaconcentration at a relatively high temperature. tion: A slight deficiency of oxygen in the combustion mixture results from the combustion gases in - consumption economy through reduced gas the fresh fuel air mixture. Thus, the combustion exchange process is not as hot in contrast to when there is an - increased partial load range with exhaust gas oxygen surplus and in this way the formation recirculation of NO x is reduced. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability smooth engine running with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� - exhaust gas recirculation already possible when the engine is cold.GB11 Engine mechanical componentsThe crankcase ventilationThe crankcase ventilation prevents gases with oil droplets (so-called blow-by gases) from the crankcase to reach the outside atmosphere. The crankcase ventilation consists of ventilation ducts in the cylinder block and in the cylinder head, the cyclone oil separator and the crankcase ventilation heating. It functions as follows The blow-by gases in the crankcase are suctioned by the intake manifold vacuum via the following components:SP69_11- ventilation ducts in the cylinder block, - ventilation ducts in the cylinder head, - cyclone oil separator, - pressure regulator valve and - crankcase ventilation heating. Subsequently, the blow-by gases are led again into the intake manifold.Cyclone oil separatorCrankcase ventilation heatingProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP69_12Ventilation ducts in the cylinder block and in the cylinder headThe cyclone oil separator The cyclone oil separator is located in the cylinder head cover. It has the task to separate the oil from the blow-by gases of the crankcase and to make it available again to the oil circulation system. A pressure control valve limits the intake manifold pressure of approx. 700 mbar to approx. 40 mbar. It prevents the same vacuum, as in the intake manifold, from prevailing in the crankcase and as a result no engine oil is sucked in or seals are damaged.Cyclone oil separator Pressure control valveSP69_13Oil outflow openingto the intake manifold12GB It functions as followsPressure control valveThe cyclone oil separator separates the oil from the suctioned blow-by gases. SFlbIt operates according to the principle of separation by centrifugal force. The suctioned blow-by gases circulate in a rotative movement due to the design of the oil separator as a cyclone. The oil from the blowby gases is sprayed onto the separating wall by means of the occuring centrifugal force. The oil droplets combine into larger drops on the separating walls and then flow into the cylinder head through an oil outflow opening in the separator. The separated blow-by gases are led back again into the intake manifold.Cyclone oil separatorIntake manifold Oil collection volumeSP69_14Inlet of blow-by gasesIf a pressure control valve is defective, the inside pressure of the crankcase corresponds to the intake manifold vacuum. A lot of oil Outlet of the sepais suctioned out of the crankcase rated gases to the via the crankcase ventilation, which intake manifold Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted can lead to engine damage.unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Gas particlesSP69_15Oil dropletsOil outflow opening in the cylinder headThe crankcase ventilation heating When the intake air is very cold, the crankcase ventilation heating prevents the blow-by gases from icing up. The heating is carried out with a heating element which is inserted into a flexible pipe. The flexible pipe leads from the cyclone oil separator to the intake manifold. The heating element is screwed to the intake manifold.flexible pipeHeating elementSP69_16GB13 Engine mechanical componentsThe intake manifoldThe 3.6 ltr. FSI engine has a two-part plastic intake manifold. The intake manifold is not switchable and therefore has no adjustable regulating flaps. The power output and torque requirements are fullfilled in the different speed ranges through an optimal duct geometry.two-part intake manifoldMain collectorSP69_17Crankcase ventilationProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The two-part intake manifold consists of an upper part of the intake manifold and a lower part of the intake manifold which are screwed together. As the intake manifold is split into two segments, this facilitates the assembly (or disassembly) and the access to the components below the intake manifold.Upper part of the intake manifoldSP69_18Lower part of the intake manifold14GB The chain driveInlet camshaft drive Outlet camshaft driveHigh-pressure fuel pumphydraulic chain tensionerFuel high-pressure pump drive and vacuum pump drive Camshaft roller chainOil pump driveMain roller chainhydraulic chain tensionerCrankshaft gearSP69_19The chain drive is located on the gearbox side of the engine. It consists of the main roller chain and the camshaft roller chain. The main roller chain is driven by the crankshaft gear. It further drives the camshaft roller chain and the oil pump via a chain sprocket.Both camshafts, the high-pressure fuel pump drive and the vaccum pump drive are driven by the camshaft roller chain. Both chains are held in the predefined chain tension by the chain tensioners.Please observe the instructions in ELSA for setting the timing. A special tool T10332 is available to stop the high-pressure fuel pump drive.GBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�15 Engine mechanical componentsThe vacuum pumpThe vacuum pump is located on the side cover of the cylinder head and ensures that in all operating conditions of the engine, a sufficiently high vacuum can be sustained for all consumers which are connected to the vacuum system. The drive of the vacuum pump is performed via the drive shaft which is driven by the fuel high-pressure pump drive. The drive shaft has a square at the end on which the vacuum pump is fitted.Rear viewSP69_20SP69_21Support for the square of the drive shaftVacuum pumpDrive shaft with squareSP69_22Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�16GB The V-ribbed belt driveThe AC compressor, the generator and the coolant pump run within the belt drive. The belt is driven by the crankshaft via the V-ribbed belt by means of a vibration damper. The V-ribbed belt is a one-sided poly-V-belt. It runs quietly and without vibrations even at high engine speeds. The V-ribbed belt is always held in the correct belt tension by means of a belt tensioner.Tensioning pulleyDrive Coolant pump Drive GeneratorGuide pulley V-ribbed belt of crankshaft with vibration damper Drive AC compressorGuide pulleySP69_23Structure of the poly-V-ribbed beltCover fabric Cover plate Pull string made of polyester SubstructureProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept liability V-ribbed belt withany vibration with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�damperSP69_24GB17 Engine mechanical componentsThe oil circulation systemCamshaft adjuster of inlet camshaft Camshaft adjuster of outlet camshaftHydraulic tappet Fuel high-pressure pump driveCamshaft bearingChain tensioner Chain tensioner Oil reservoir Oil pumpVacuum pump Spray nozzles for piston cooling Oil reservoir Crankshaft bearing Oil returnSuction channelOil filter radiator moduleProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Oil panSP69_25The oil pressure is produced by a duocentric oil pump which is installed in the cylinder block and is driven by the chain drive of the crankshaft gear. A relatively long oil suction path, which is disadvantageous for the main oil supply of the components, is the result of the installation position of the oil pump.To ensure that all the lubrication points of the engine are immediately lubricated after the engine start, the oil is extracted from an oil reservoir which is located just behind the oil pump.18GB The oil pump with oil reservoir The oil reservoir is formed in the cylinder head by a hollow space behind the oil pump. It has a capacity of approx. 280 ml and the oil remains here even after switching off the engine.Cylinder headPinion gear driveOil reservoirService opening Oil pump Cylinder blockSP69_26The service opening of the oil pump The service opening enables the access to the oil overpressure piston of the oil pump when the engine is installed. After screwing out the cover screw and a second inner screw, the pressure piston of the oil pump can be removed though this opening without disassembling the chain drive.Pressure pistonSP69_28Cover screwSP69_27GBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�19 Engine mechanical componentsThe oil filter radiator module The oil filter radiator module is formed by the following components: - Oil filter - Oil cooler - Return flow stop valve - Bypass valveOil coolerSP69_29Oil filter Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The oil return The oil which flows back is led into a central oil return-flow channel in the cylinder block via three return-flow channels in the cylinder head and from there it then flows into the oil pan. In addition to the central oil return flow channel, oil is led back into the oil pan via the chain drive shaft.SP69_30central oil return flow channel20GB The cooling circuit12Legend 1 - Expansion reservoir 2 - Heat exchanger for heating 3 - Coolant pump 4 - Gearbox oil cooler 5 - Coolant regulator (thermostat) 6 - Oil cooler 7 - Non-return valve 8 - Circulation pump V55 9 - Additional cooler 10 - Cooler345 6 787 910 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted SP69_31 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The coolant circulates by means of a mechanical coolant pump. It is driven by the V-ribbed belt. In the cooling circuit are 9 litres of coolant. The circulation is regulated by an expanding material thermostat (coolant regulator).The non-return valves are integrated in the cooling circuit in such a way that they prevent the coolant from flowing back. For vehicles which are intended for countries with tropical climate, an additional cooler is integrated in the cooling circuit.GB21 Engine mechanical componentsThe circulation pump V55 The circulation pump relay V55 is an electrical pump which is integrated in the cooling circuit and is actuated by the engine control unit using a performance map. After stopping the vehicle or in the absence of headwind, it switches on depending on the coolant temperature.SP69_32The radiator fans The 3.6 ltr. FSI engine has two electrical radiator fans in order to cool the cooling circuit. The radiator fans are actuated by the engine control unit depending upon use. The engine control unit J623 notifies the radiator fan control unit J293 if the radiator ventilation is required. Then the radiator fan control unit J293 supplies voltage to one or both radiators. The voltage supply of the radiator fan control unit J293 is delivered via the Motronic current supply relay J271 and the onboard supply control unit J519. The fans can also be switched on by the radiator fan control unit J293 after stopping the vehicle. In order to switch on the fans when the vehicle is stopped, the radiator fan control unit J293 has a connection to terminal 30.Engine control unit J623Radiator fan V7Radiator fan 2 V177 Motronic currentsupply relay J271 purposes, in part or in whole, is not permitted Protected by copyright. Copying for private or commercial unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP69_33SS Terminal 30Onboard Radiator fan supply control control unit unit J519 J29322GB The exhaust systemG39Main catalytic converter G130G108G131SP69_34LegendG39 G108 G130 G131-linear lambda probe before catalytic converter (right) linear lambda probe before catalytic converter (left) Snap-action lambda probe after catalytic converter (right) Snap-action lambda probe after catalytic converter (left)The exhaust system of the 3.6 ltr. FSI engine has one main catalytic converter with ceramic support for each bank. The exhaust gas quality is assessed by means of two lambda probes located in front and behind the catalytic converter. The exhaust system corresponds to the emission standard EU4 plus.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB23 The fuel systemThe fuel systemLow-pressure lineThe fuel low-pressure system The electric fuel pump for predelivery G6 delivers the fuel from the fuel tank to the low-pressure line and then to the high-pressure fuel pump via the fuel filter with fuel pressure regulator. For this reason, the fuel pump for predelivery G6 is operated by the engine control unit J623 via the fuel pump control unit J538. The fuel pump for predelivery G6 produces a pressure between 2 and 5 bar in the low-pressure line depending upon use. It functions as followsPressure regulator valveFuel filter with fuel pressure regulatorThe fuel pressure sender for low pressure G410 is located in the low-pressure line and transmits the information of the current fuel pressure to the engine control unit. On the basis of this information, the engine control unit compares the current pressure with the current fuel pressure required. If the current fuel pressure is not sufficient in order to meet the current fuel requirement, the engine control unit J623 actuates the fuel pump control unit J538. Then it actuates the fuel pump Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted for predelivery G6 which increases the operating unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability G6 pressure. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� If the fuel requirement decreases again, the operating pressure of the fuel pump for predelivery G6 is also reduced accordingly. High-pressure fuel system The pressure holding valve maintains the fuel pressure in the low-pressure line when the engine is switched off. If the fuel line pulls off during an accident, the pressure holding valve prevents the fuel from flowing out of the tank.Pressure holding valveThe fuel pressure sender, high pressure G247 The fuel pressure sender G247 (high pressure) is installed on the fuel distributor pipe of cylinder bank 2 and informs the engine control unit about the current fuel pressure in the high-pressure line. The fuel pressure control valve N276 The fuel pressure control valve N276 is located on the fuel high-pressure pump and regulates the pressure in the high-pressure line according to the signal in the engine control unit.The pressure regulator valve in the fuel tank opens at a pressure of 6.4 bar and therefore prevents that the fuel pressure is too high in the low-pressure line. Now the surplus fuel can flow into the storage pan of the fuel pump.24GB G410High-pressure linePressure regulator valve High-pressure fuel pumpDistributor strip Cylinder bank 1Injection nozzle Cylinder 1Injection nozzle Cylinder 3Injection nozzle Cylinder 5N276Distributor strip Cylinder bank 2 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�G247 J623 Injection nozzle Cylinder 2 J538 Injection nozzle Cylinder 4 Injection nozzle Cylinder 6SP69_35The pressure regulator valve The pressure regulator valve is located on the fuel distributor pipe of cylinder bank 1. The valve discharges fuel into the low-pressure line in case the pressure in the high-pressure line rises above 120 bar.Legend G6 G247 G410 J538 J623 N276 Fuel pump for predelivery Fuel pressure sender for high pressure Fuel pressure sender for low pressure Fuel pump control unit Engine control unit Fuel high-pressure control valveGB25 The fuel systemThe high-pressure fuel pump The high-pressure fuel pump is a piston pump and is located on the cylinder head. It is driven by the camshaft roller chain and produces a fuel pressure of maximum 105 bar.Fuel low-pressure line Fuel high-pressure lineFuel high-pressure pumpFuel pressure control valve N276SP69_36The fuel high-pressure pump drive The fuel high-pressure pump is driven via a toothed gear with double cam. The pump piston which produces the high-pressure is operated by the double cam via a roller.Pinion gear drive Fuel high-pressure pumpProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Pump plunger Cylinder head Bucket tappet Roller Double camBucket tappetSP69_37Pinion gear driveSP69_38Double camIn order to fit on the camshaft roller chain, the toothed gear of the fuel high-pressure pump is locked using the special tool T10332.26GB The injection valvesOutlet valve Inlet valveThe injection valves are inserted from the same side on both cylinder banks, this is why the piston recesses must be formed differently. This is required because the injection valves and the inlet valves of both cylinder banks are arranged at different angles. Besides the injection quantity and the injection time, the shape and the orientation of the fuel jet also have an important function.Injection valve Piston recessValve angle, cylinders 1, 3, 5SP69_39Valve pocketValve angle, cylinders 2, 4, 6SP69_40Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability The homogeneous split - catalyticunless converter with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Catalytic heating process late ignition timingconverterIt has the task to quickly heat up the catalytic converter to its operating temperature during cold start. The first injection takes place in the suction stroke through which an even distribution of the fuel-air mixture is achieved. During the second injection, only a small quantity of fuel is injected shortly before ignition TDC. This fuel-air mixture burns later than the mixture of the first injection. Therefore, the exhaust gas temperature increases and the catalytic converter heats up more quickly to the operating temperature.hotter combustion gases second injectionSP69_41GB27 Engine managementSystem overviewSensorsEngine speed sender G28Air mass meter G70Accelerator pedal position sender G79/ Accelerator pedal position sender 2 G185Throttle valve control module J338/ Throttle valve drive angle sender 1 G187/ Throttle valve drive angle sender 2 G188 Engine control unit J623 Hall sender G40/ Hall sender 2 G163Protected Coolant temperature sender G62/ by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Radiator outlet coolant temperature sender G83 of information in this document. Copyright by ŠKODA AUTO A. S.� with respect to the correctnessKnock sensor 1 G61/ knock sensor 2 G66Brake light switch FFuel pressure sender G247Fuel pressure sender for low pressure G410 Oil level and oil temperature sender G266 Lambda probe before catalytic converter G39/ Lambda probe 2 before catalytic converter G108 Lambda probe after catalytic converter G130/ Lambda probe 2 after catalytic converter G131CAN data bus drive28GB ActuatorsFuel pump control unit J538/ Fuel pump for pre-supply G6Injection valve, cylinders 1-6 N30, N31, N32, N33, N83, N84Ignition coil 1-6 with output stage N70, N127, N291, N292, N323, N324Throttle valve control module J338/ Throttle valve drive for electric throttle control G186Fuel pressure control valve N276 Activated charcoal filter system solenoid valve N80CAN data bus dash panel insertCamshaft adjustment valve 1 N205/ Camshaft adjustment valve 1 in the outlet N318 Lambda probe heater before catalytic converter Z19/ Lambda probe heater 2 before catalytic converter Z28 Lambda probe heater after catalytic converter Z29/ Lambda probe heater 2 after catalytic converter Z30Control unit in dash panel insert J285Radiator fan control unit J293/ Radiator fan V7/ Radiator fan 2 V177 Circulation pump relay J160/ Circulation pump V55SP69_43Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB29 Engine managementThe sensorsThe engine speed sender G28 The engine speed sender is screwed onto the cylinder block and scans the speed of the sensor rotor on the crankshaft.Use of signal The speed of the engine and the exact position of the crankshaft to the camshafts is determined by the signal of the engine speed sender. The start of injection and the injection quantity are calculated according to this information.SP69_42Effects of signal failure If the signal of the engine speed sender fails, the engine is switched off and can no longer be started.The air mass meter G70 The hot-film air mass meter of the 6th generation (HFM6) is installed in the 3.6 ltr. FSI engine. It is located in the suction channel of the engine and functions according to a thermal measurement principle just like its predecessor. Its features are: - a micromechanical sensor element with reverse current detection - signal processing with temperature compensation - high measuring accuracy - high sensor stabilityConnector plugSensor electronicsdrawn-in airSP69_44Protected by copyright. Copying for private or commercial purposes, in part Bypass or in whole, duct is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�30GB It functions as follows The sensor element integrated in the air mass meter protrudes into the air flow of the drawn-in air from the engine. One part of the drawn-in air flows through the bypass duct in which the sensor electronics is located. A heating resistor and two temperature sensors are integrated in the sensor electronics. The air mass and the flow direction of the air is determined by both temperature sensors.SP69_45Measurement of the drawn-in airThe drawn-in air mass is determined on the basis of the temperature difference of the temperature sensors 1 and 2. The flow direction is calculated upon the fact that the temperature difference of the temperaturesensors 1 and 2 is greater or smaller than zero.Sensor elementTemperature sensor 2 Heating resistor Temperature sensor 1 Air flow of intake airSP69_46Use of signal The engine control unit uses the signal of the air mass meter in order to calculate: the ignition timing, the injection timing, the quantity of fuel injected and the actuation of the recirculation system of the fuel vapours in the engine intake system (activated charcoal filter system).Measurement of the reverse current air when the valves are closedEffects of signal failure If the air mass meter fails, the engine management calculates a replacement value.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP69_47reverse current airTemperature sensor 2 Heating resistor Temperature sensor 1SP69_48GB31 Engine managementThe accelerator pedal position sender G79 and the accelerator pedal position sender 2 G185 Both accelerator pedal position senders are a component part of the accelerator pedal module and operate according to the principle of the touchless position detection (induction sensor). The engine control unit detects the current accelerator pedal position by means of the signals of these sensors.Use of signal The engine control unit uses the signals of the accelerator pedal position sender for calculating the injection quantity.Accelerator pedal G79 and G185SP69_49Effects of signal failure If one of the two senders fails, an entry is made in the fault memory and the fault indicator lamp for electric throttle control in the dash panel insert is switched on. As a result, the convenience functions and the safety systems which influence the torque, for example the cruise control system or the engine towing torque control (MSR), are switched off.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�32GB Throttle valve drive angle sender 1 G187 and throttle valve drive angle sender 2 G188 The current position of the throttle valve is determined by means of the signals of both senders and afterwards this information is transmitted to the engine control unit. The senders operate according to the principle of the touchless detection (magnetoresistive sensor).Use of signal The signals of both senders are redundant, which means that both senders deliver the same signal for reasons of driving safety.Throttle valve housingThrottle valve driveSP69_51Throttle valveG187 and G188Effects of signal failure Example 1 The engine control unit receives an implausible signal or no signal at all from an angle sender: - an entry is made in the fault memory and the fault indicator lamp for electric throttle control in the dash panel insert is switched on - the convenience functions and the safety systems which influence the torque (e.g. the cruise control system or the engine towing torque control) are switched off - in order to test the remaining angle sender, the load signal is used - the accelerator pedal responds like normal. Example 2 The engine control unit receives an implausible signal or no signal at all from both angle senders: - an entry is made in the fault memory for both senders and the fault indicator lamp for electric throttle control in the dash panel insert is switched on - the throttle valve drive is switched off - the engine only runs with increased idle speed of approx. 1500 rpm and does no longer respond to the accelerator pedal.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB33 Engine managementThe Hall senders G40 and G163 Both Hall senders operate according to the principle of the touchless detection and are arranged in the timing chain cover of the engine. Each Hall sender scans a quickstart sensor rotor which is located on the respective camshaft. The engine control unit detects the position of the inlet camshaft by means of the Hall sender G40 and the position of the outlet camshaft by means of the Hall sender 2 G163.G40G163SP69_52Use of signalEffects of signal failureWhen the engine is started, the exact position In the event of a signal failure of the Hall senders of the camshafts to the crankshaft is determined G40 and G163, the signal of the engine speed very quickly using the signal of the Hall sender. sender G28 is used. Due to the fact that the camTogether with the signal of the engine speed shaft position and the cylinder position cannot be Protected by copyright. Copying for or commercial purposes, determined in part or in whole, is not quickly, permitted the engine start can take sender G28, the cylinder which isprivate located in the as unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability ignition TDC can be determined. slightly longer. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Through this, the corresponding cylinder is specifically injected and ignited.34GB The coolant temperature sender G62 The coolant temperature sender is located on the coolant distributor above the oil filter and informs the engine control unit about the coolant temperature.Use of signal The coolant temperature is used by the engine control unit for various engine functions, for example for the calculation of the injection quantity, the load pressure, the start of delivery and the exhaust gas recirculation quantity.SP69_53Effects of signal failure If the signal of the coolant temperature sender G62 fails, the engine control unit uses the signal of the coolant temperature sender on the radiator outlet G83.G62The coolant temperature senderwith - radiator outlet G83 respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� The coolant temperature sender G83 is located in the line on the radiator outlet and there it measures the initial temperature of the coolant from the radiator.Radiator inletProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilityUse of signal In order to perform the actuation of the radiator fan, both signals of the coolant temperature senders G62 and G83 must be compared.Radiator outletEffects of signal failure If the signal of the coolant temperature sender G83 fails, both radiator fans are permanently actuated.G83SP69_54GB35 Engine managementThe knock sensor 1 G61 and the knock sensor 2 G66 The knock sensors are screwed onto the crankcase and inform the engine control unit about the knocking combustion of the individual cylinders. The knock sensor G61 is determined for the cylinder group 1 and the knock sensor G66 is determined for the cylinder group 2. In order to avoid knocking combustion, a cylinder-selective knock control superposes the electronic control of the ignition timing.SP69_55SP69_56G61G66Use of signal The engine control unit initialises an ignition angle adjustment for individual cylinders by means of the signals of the knock sensors until knocking combustion no longer occurs.Effects of signal failure If a knock sensor fails, the ignition angle of the relevant cylinder group is withdrawn. This means that a subsequent ignition angle is set. This can result in an increase of the fuel consumption. The knock control for the cylinder group of the remaining intact knock sensor stays in effect. If both knock sensors fail, the engine management changes into the knock sensor emergency mode whereby the ignition angle of both cylinder groups is withdrawn and in this way the knock combustion is avoided. However, this results in the reduction of the engine performance.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�36GB The brake light switch F The brake light switch is located on the tandem main cylinder and operates according to the principle of the touchless detection (Hall sensor). The position of the magnetic ring on the piston of the tandem main cylinder is determined with a Hall element. The information concerning the brake pedal actuation is read by the engine control unit and is then transmitted to the CAN data bus drive.SP69_57Use of signal The signal of the brake pedal actuation is used for switching on the brake lights and for switching off the cruise control system. If first of all "accelerator pedal depressed" and in addition "brakes operating" is detected, an increase of the idle speed is regulated.Effects of signal failure If the signal of the sender fails, the injection quantity is reduced and the engine has less power output. The cruise control system is switched off.The fuel pressure sender for high pressure G247 The fuel pressure sender G247 (high pressure) is installed on the fuel distributor pipe of Copying cylinder Protected by copyright. for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability bank 2 and informs the engine control unit about with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� the current fuel pressure in the high-pressure line.Use of signal The engine control unit evaluates the signal and regulates the fuel high-pressure in the high pressure pump via the fuel pressure control valve N276.Effects of signal failure If the fuel pressure sender G247 fails, the fuel pressure control valve N276 is actuated by the engine control unit with a predefined constant value.G247SP69_58GB37 Engine managementThe fuel pressure sender for low pressure G410 The fuel pressure sender for low pressure G410 is located in the low-pressure line and transmits the information of the current fuel pressure in the fuel line to the engine control unit.Use of signal The signal of the sender is used by the engine control unit in order to control the fuel pressure in the low-pressure line. By way of the signal of the fuel pressure sender G410, the fuel pump control unit J538 which operates the electric fuel pump for predelivery G6 depending upon use, is actuated by the engine control unit.SP69_59Effects of signal failure If the fuel pressure sender G410 fails, the fuel pressure is no longer controlled depending upon use. The fuel pressure in the low-pressure line is constantly maintained at approx. 5.5 bar. The oil level and oil temperature sender G266 The sender G266 is screwed onto the oil pan from below and is connected to the control unit in the dash panel insert J285 using a single conductor cable.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilityUse of signal with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� The control unit in dash panel insert J285 uses this signal to calculate extended maintenance intervals. Furthemore, the signal is transmitted to the CAN data bus where it is used by several control units – for example the enginecontrol unit uses it to receive the information concerning the oil temperature in order to control the adjustment of the outlet camshaft.Effects of signal failureSP69_60If the sender G266 fails, the signal of the coolant temperature sender G62 is used instead.38GB Lambda probe 1 before catalytic converter G39 and lambda probe 2 before catalytic converter G108linear lambda probeThe lambda probes G39 and G108 are located before the main catalytic converter of each cylinder bank. These are linear lambda probes. The oxygen concentration in the exhaust gas can be determined to a large extent using the linear lambda probes and thus the air-fuel ratio in the combustion chamber is maintained. Both lambda probes are heated in order to reach the operating temperature more quickly.SP69_61Use of signal The signals of the lambda probes are one size in order to calculate the injection time.Effects of signal failure If the upstream of catalytic converter probe fails, no lambda control is performed and the engine runs in emergency mode by means of a performance map stored in the engine control unit.Lambda probe 1 after catalytic converter G130 and lambda probe 2 after catalytic converter G131Snap-action lambda probeThe lambda probes G130 and G131 are located behind the main catalytic converter of each cylinder bank. These lambda probes are snap-action lambda probes and measure the residual oxygen in the exhaust gas. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. residual S. ŠKODA AUTO A. S. does not guarantee or accept any liability Depending on the oxygen in the exhaust with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� gas, the engine control unit can assess the function of the catalytic converter.SP69_62Use of signal The engine control unit uses the signals of the downstream of catalytic converter probe in order to test the function of the catalytic converter and the lambda control loop.Effects of signal failure If the downstream of catalytic converter probe fails, the lambda control continues, however the function of the catalytic converter cannot be checked.GB39 Engine managementActuatorsCamshaft adjustment valve 1 N205 and camshaft adjustment valve 1 in the outlet N318The electromagnetic valves N205 and N318 are integrated in the timing case of the camshaft adjustment. They distribute the oil pressure to the wing cell adjuster of the camshafts depending on the specifications of the engine control unit which refers to the direction of adjustment and the adjustment track.Both camshafts are continuously adjustable: - Inlet camshaft of 52 crank angle degrees - Outlet camshaft of 42 crank angle degrees - Maximum valve overlap angle of 42 crank angle degrees The exhaust camshaft is mechanically locked if no oil pressure is present (e.g. when the engine is standing in still motion).N205 N318SP69_63Effects of signal failure If the electromagnetic camshaft adjustment valve or the wing cell adjuster of the camshaft is defective, or if the oil pressure is too low, a camshaft adjustment is no longer possible.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�40GB The fuel pump control unit J538 The fuel pump control unit J538 is located under the right rear seat and is fixed on the housing of the electric fuel pump G6.It functions as follows The fuel pump control unit J538 receives instructions from the engine control unit J623 (PWM signal) concerning the demands on the fuel quantity. SFlbAfterwards, it actuates the electric fuel pump G6.Effects of failure If the fuel pump control unit fails, an engine operation is no longer possible.J538SP69_64The electric fuel pump G6 The electric fuel pump G6 and the fuel filter are combined in the fuel delivery unit. The fuel delivery unit is located in the fuel tank.Fuel delivery unitFuel filterTask The electric fuel pump delivers the fuel from the fuel tank to the high-pressure fuel pump via the low-pressure line. The electric fuel pump builds up a pressure G6 between 2 and 5.5 bar in the low-pressure line Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability depending on the PWM signal.with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The electric fuel pump always delivers at that moment as much fuel to the high-pressure fuel pump as it needs.SP69_65Effects of failure If the electric fuel pump fails, an engine operation is no longer possible.GB41 Engine managementThe fuel pressure control valve N276 The fuel pressure control valve is located at the bottom side of the high-pressure fuel pump. The engine control unit controls the fuel highpressure between 35 and 100 bar via the fuel pressure control valve.Effects of failure If the fuel pressure control valve fails, the engine control unit goes into emergency mode.High-pressure fuel pumpN276SP69_66The ignition coils 1-6 with output stages N70, N127, N291, N292, N323, N324 The ignition coil and the output stage are one component. The ignition angle is separately controlled for each cylinder.Effects of failure If an ignition coil fails, the injection of the relevant cylinder is interrupted.SP69_67Ignition coilsFor reason of clarity, only three or six ignition coils are shown in the figure.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�42GB The activated charcoal filter system solenoid valve N80 The activated charcoal filter system solenoid valve is located next to the intake manifold on the side of the belt drive. The solenoid valve has the task to lead the fuel vapours, which are collected in the activated charcoal filter system, into the intake manifold.Effects of failure If the power supply of the activated charcoal filter system solenoid valve is interrupted, the valve remains closed. Therefore a tank ventilation does not take place.SP69_68The injection valves, cylinders 1-6 N30, N31, N32, N33, N83, N84 The high-pressure injection valves are inserted in the cylinder head. They are actuated by the engine control unit according to the ignition sequence. The injection for both cylinder banks is performed from one side due to the design of the engine. Therefore, the injection valves of the cylinder banks 1, 3 and 5 are longer than the injection valves of the cylinder banks 2, 4 and 6.Effects of failureSP69_69If a fault (e.g. misfire) of an injection valve is detected, the valve is no longer actuated by the control unit.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB43 Engine managementThe throttle valve drive G186 The throttle valve drive is an electric motor which operates the throttle valve via a toothed gear drive. The adjustment range of the throttle valve is stepless from idle up to full load position, at which the throttle valve is fully opened.Throttle valve housing G186Effects of failure If the throttle valve drive fails, the throttle valve is automatically drawn into the emergency position. An entry is made in the fault memory and the fault indicator lamp for electric throttle control in the dash panel insert is switched on. The convenience and safety systems, which influence the torque, are switched off.SP69_70Throttle valveThe circulation pump V55 The circulation pump is actuated by the engine unless authorised by ŠKODA AUTO A. S. Š KODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� control unit and supports the function of the mechanical coolant pump. After stopping the vehicle or in the absence of headwind, it switches on depending on the coolant temperature and avoids a heat build-up in the engine.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedEffects of failure If the circulation pump fails, the engine can overheat.SP69_75V5544GB The heating of the lambda probes Z19, Z28, Z29, Z30 The lambda probe heating has the task to bring the ceramic of the probe as quickly as possible to its operating temperature (approx. 900°C). The lambda probe heating is controlled by the engine control unit.Lambda probe heatingSP69_76Effects of failure If the lambda probe fails, the exhaust emissions can no longer be regulated. The control units in the CAN data busJ743 J217 J104 J623J533 J285 J519 J234Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilityJ527SP69_78Legend with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� data bus drive CAN J623 J104 J217 J234 J285 J519 J527 J533 J743 Engine control unit ABS/ESP control unit Automatic gearbox control unit Airbag control unit Control unit in dash panel insert Onboard supply control unit Steering column electronics control unit Data bus diagnostic interface (GATEWAY) Double clutch gearbox mechatronics CAN databus Convenience CAN databus infotainmentGB45 Engine managementFunction diagramProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP69_71G39 G130 J160 J271 J519 J623 J670 N30 N31 N70 N127Lambda probe 1 before catalytic converter (right) Lambda probe 1 after catalytic converter (right) Circulation pump relay Motronic current supply relay Onboard supply control unit Engine control unit Motronic current supply relay 2 Injection valve, cylinder 1 Injection valve, cylinder 2 Ignition coil 1 with output stage Ignition coil 2 with output stageN291 N292 N323 N324 Z19 Z29 V55Ignition coil 3 with output stage Ignition coil 4 with output stage Ignition coil 5 with output stage Ignition coil 6 with output stage Lambda probe heater before catalytic converter Lambda probe heater after catalytic converter Circulation pump46GB Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP69_72F F1 G G1 G5 G6 G21 G28 G61 G66 G79 G185Brake light switch Oil pressure switch Fuel gauge sender Fuel gauge Rev counter Fuel pump for predelivery Speedometer Engine speed sender Knock sensor 1 Knock sensor 2 Accelerator pedal position sender 1 Accelerator pedal position sender 2G186 G187Throttle valve drive for electric throttle control Throttle valve drive angle sender 1 for electric throttle control G188 Throttle valve drive angle sender 2 for electric throttle control G266 Oil level and oil temperature sender J285 Control unit in the dash panel insert J338 Throttle valve module J519 Onboard supply control unit J538 Fuel pump control unit J623 Engine control unit N276 Fuel pressure control valveGB47 Engine managementFunction diagramProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP69_73G40 G83 G108 G131 G163 G247 G410 J293 J519 J623 N32 N33Hall sender Coolant temperature sender at radiator outlet Lambda probe 2 before catalytic converter (left) Lambda probe 2 after catalytic converter (left) Hall sender 2 Fuel pressure sender for high pressure Fuel pressure sender for low pressure Radiator fan control unit Onboard supply control unit Engine control unit Injection valve, cylinder 3 Injection valve, cylinder 4N80 N83 N84 N205 N318 V7 V177 Z28 Z30Activated charcoal filter system solenoid valve Injection valve, cylinder 5 Injection valve, cylinder 6 Camshaft adjustment valve 1 Camshaft adjustment valve 1 in the outlet Radiator fan Radiator fan 2 Lambda probe heater 2 before catalytic converter Lambda probe heater 2 after catalytic converter48GB Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP69_74G62 G42 G70 J519 J527 J533 J623Coolant temperature sender Intake air temperature sender Air mass meter Onboard supply control unit Steering column electronics control unit Data bus diagnostic interface Engine control unitPlus Earth Output signal Input signal CAN data busGB49 NotesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�50GB Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB51 List of Self-Study Programmes so farNo.1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50TitleNo.TitleMono-Motronic Central locking Anti-Theft Alarm Working with current flow diagrams ŠKODA FELICIA ŠKODA-Vehicle safety Principles of ABS - not published ABS-FELICIA Immobilizer with transponder Air conditioning in vehicles Air conditioning FELICIA 1.6-ltr. engine with MPI 1.9-ltr. Naturally aspirated diesel engine Power-assisted steering ŠKODA OCTAVIA 1.9-ltr. TDI engine OCTAVIA Convenience electronic system OCTAVIA Manual gearbox 02K/02J 1.6 ltr./1.8 ltr. petrol engines Automatic gearbox - fundamentals Automatic gearbox 01M 1.9 ltr./50 kW SDI, 1.9 ltr./81 kW TDI 1.8 ltr. 110 kW turbo petrol engine 1.8 ltr. 92 kW petrol engine OCTAVIA, CAN databus OCTAVIA - CLIMATRONIC OCTAVIA - Vehicle safety OCTAVIA - 1.4-ltr. Engine and Gearbox 002 OCTAVIA - ESP OCTAVIA - 4x4 2.0 ltr. 85 kW/88 kW petrol engine OCTAVIA - Radio/navigation system ŠKODA FABIA ŠKODA FABIA - Vehicle electrics ŠKODA FABIA - Power-assisted steering 1.4 ltr. - 16V 55/74 kW petrol engines ŠKODA FABIA - 1.9 ltr. TDI Unit injection 5-Speed manual gearbox 02T and 002 ŠkodaOctavia - Model 2001 Euro-On-Board-Diagnosis Automatic gearbox 001 6-Speed manual gearbox 02M ŠkodaFabia - ESP Exhaust emission Extended maintenance interval 1.2 ltr. 3-cylinder petrol engines ŠkodaSuperb; Presentation of the vehicle part I ŠkodaSuperb; Presentation of the vehicle part II ŠkodaSuperb; 2.8-ltr./142 kW V6 petrol engine ŠkodaSuperb; 2.5-ltr./114 kW TDI V6 Diesel engine ŠkodaSuperb; Automatic gearbox 01V51 2.0 ltr./85 kW Petrol Engine with balance shaft transmission and 2-stage switching intake manifold 52 ŠkodaFabia; 1.4-ltr. TDI engine with unit injection system 53 ŠkodaOctavia; Presentation of the vehicle 54 ŠkodaOctavia; Electrical Components 55 FSI Petrol Engines; 2.0 ltr./110 kW and 1.6 ltr./85 kW 56 Direct manual gearbox 57 Diesel engine 2.0 ltr./103 kW TDI Unit injector 2.0 ltr./100 kW TDI Unit injector 58 ŠkodaOctavia; Chassis and electromechanical power-assisted steering 59 ŠkodaOctavia RS, 2.0 ltr./147 kW FSI turbo petrol engine 60 2.0 ltr./103 kW 2V TDI diesel engine; diesel particle filter system with additive 61 Satellite navigation systems in Škoda vehicles 62 ŠkodaRoomster; Presentation of the vehicle part I 63 ŠkodaRoomster; Presentation of the vehicle part II 64 ŠkodaFabia II; Presentation of the vehicle 65 ŠkodaSuperb ll; Presentation of the vehicle part I 66 ŠkodaSuperb ll; Presentation of the vehicle part II 67 2.0 ltr./125 kW TDI diesel engine with Common Rail injection system 68 1.4 ltr./92 kW TSI petrol engine with turbocharging 69 3.6 ltr./191 kW FSI petrol engineOnly intended for internal use in the Škoda-Organisation. All rights reserved. Subject to technical modification. S00.2002.69.20 CZ Technical status 11/2008 GB © ŠKODA AUTO a.s. http://portal.skoda-auto.comThis paper was made out of chlorine-fre