TECHNICAL DOCUMENTATION

SSP 279 The 2,0 l 110 kW engine with petrol direct injection (FSI)

PDFEN44 pages1,018 KB
SSP 279 The 2,0 l 110 kW engine with petrol direct injection (FSI) - PDF cover

This PDF is currently unavailable.

Read document text
279Service.The 2.0 l 110 kW engine with petrol direct injection (FSI) Self Study Programme 279For internal use only Improved methods of injecting petrol into the intake port represent more or less the limit of what can be done to optimise economy with conventional techniques. The direct injection principle opens up new possible ways of creating more economical and environmentally sound petrol engines.Thrifty diesel engines employ direct injection, in other words, the amount of fuel supplied corresponds exactly to the requirements at any given time.The logical next step - at least in theory - would therefore be to apply the principle of direct injection to petrol engines as well. FSI technology from Audi opens up a whole new dimension for the petrol engine. ContentsPage IntroductionHighlights of the FSI engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.0 l FSI engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5EngineCrankcase breather . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Pistons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Oil circulation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Cylinder head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Camshaft positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Lower part of intake manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Intake air routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 System components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 CAN bus interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Engine control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Modes of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Stratified charge operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Homogeneous operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Single-plunger high-pressure pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Fuel metering valve -N290 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Fuel rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Fuel pressure sender -G247 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 High-pressure injectors -N30, -N31,-N32, -N33 . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Exhaust-gas temperature sender -G235 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Exhaust gas treatment system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 NOx storage catalytic converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Regeneration phases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 NOx sender -G295 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Exhaust-gas temperature sender -G235 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Exhaust-gas recirculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Special tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40The Self Study Programme contains information on design features and functions. The Self Study Programme is not intended as a Workshop Manual. Values given are only intended to help explain the subject matter and relate to the software version applicable when the SSP was compiled. Use should always be made of the latest technical publications when performing maintenance and repair work.NewAttention Note3 IntroductionHighlights of the FSI engineHigh-pressure injection system with newly developed single-plunger high-pressure pump279_041Air-controlled combustion process with map-controlled in-cylinder flow (stratified charge and homogeneous operation)279_025279_030Enhanced exhaust gas treatment system with NOx storage catalytic converter and NOx sender279_0074 2.0 l FSI engineTorque [Nm]279_001Engine speed rpm279_008Technical data: Engine code letters: Capacity: Bore: Stroke: Compression ratio: Power: Torque: AWA 1984 ccm 82.5 mm 92.8 mm 11.5: 1 110 kW (150 hp) 200 Nm/ 3250-4250 rpm Inlet camshaft adjustment range: 42° crankshaft Emission class: Capacities: Consumption: (5-speed manual gearbox) EU IV Engine oil incl. filter 4.8l Urban Non-urban Average 9.9l/100 km 5.4l/100 km 7.1l/100 km Valve timing: Inlet opens Inlet closes Exhaust opens Exhaust closes 28° after TDC 48° after BDC 28° before BDC 8° before TDCEngine management system: Valves: Valve timing:MED. 7.1.1 4 per cylinder Roller-type rocker fingers with hydraulic support elementsPower [kW]5 EngineEngine blockThe engine block is made of an aluminium alloy and is the most compact type in its class with a cylinder spacing of 88 mm and an overall length of only 460 mm. The engine block is identical to that of the 2.0 l engine with manifold injection (crankshaft, conrods, balance shafts and oil pump).279_009Crankcase breatherThe blow-by gases are routed from the engine block directly into the first oil separator. The majority of the oil particles are removed from the gases in the oil separator labyrinth. From there, the gases pass via the hose connection into the integrated labyrinth of the cylinder head cover and then as virtually oil-free blow-by gases into the intake manifold by way of the pressure control valve.279_0466 PistonsUse is made of lightweight aluminium alloy solid-skirt pistons with closely spaced piston pin bosses. Advantage: Reduced oscillating masses and lower coefficients of friction as only a part of the piston skirt periphery runs in the cylinder.A bowl incorporated into the piston crown aims the air flow directly towards the spark plug in stratified charge operation. The geometric shape of the piston causes the air flow to "tumble".279_010Oil circulationThe use of a 4-valve cylinder head with rollertype rocker fingers represents a major change in oil gallery design with respect to the 5-valve cylinder head with bucket tappets. Passing via the main oil gallery from the engine block, the oil enters the cylinder head between cylinders 3 and 4. Oil pressure is applied to the hydraulic support elements and camshaft bearings by way of two oil ducts. The support elements are provided with a spray orifice for lubrication of the roller-type rocker fingers. Further along the oil ducts, oil pressure is applied to the rotary motor for camshaft adjustment.279_011 7 EngineCylinder headThe 4-valve cylinder head with roller-type rocker fingers is designed to suit the direct injection process. Valve timing is provided by way of two composite overhead camshafts rigidly mounted in a ladder frame. The exhaust camshaft is driven by a toothed belt, which in turn drives the inlet camshaft by way of a simple chain. Each intake port is split into a top and bottom half by a tumble plate, the shape of which is designed to prevent incorrect installation. The mounts for the high-pressure injectors are integrated into the cylinder head, with the actual injectors projecting directly into the combustion chamber.Ladder frameExhaust camshaftInlet camshaftTumble plate279_013 8 The valve gear takes the form of a "light valve gear" (i.e. with one valve spring only).The valves are actuated by two composite camshafts via roller-type rocker fingers which rest on hydraulic valve lifters.Roller-type rocker fingerComposite camshaft279_015The valve cover is made of plastic and features a permanently attached elastomer seal.The valve cover contains the pressure control valve for the crankcase breather and the internal oil separator.Valve coverPressure control valveOil separator279_0169 EngineCamshaft timing controlContinuous map-controlled hydraulic camshaft adjustment by up to 42° crank angle is achieved by way of a rotary motor. The toothed belt drives the exhaust camshaft. The rotor of the motor is attached to the other end of the exhaust camshaft. The stator is connected directly to the chain sprocket and drives the inlet camshaft via the chain. The stator adjustment is transmitted by way of the chain to the inlet camshaft, thus varying the inlet valve timing.The Hall sender wheel and high-pressure pump drive are attached to the front and rear end of the inlet camshaft respectively.For details of camshaft timing control, refer to SSP 25510 Camshaft positioningThe inlet and exhaust camshafts must be turned such that the recesses are vertically opposed. In this camshaft position the drive chain can be fitted without having to determine the number of rollers. This is also the only position in which the cylinder head bolts can be inserted and removed.279_060The tightening torque for the cylinder head bolts is given in the latest Workshop Manual in ELSA (electronic service information system).Camshaft rotary motor42° /2279_021Double cam279_06111 EngineIntake manifoldThe two-stage variable intake manifold promotes the desired power and torque characteristics. Pneumatic switching of the changeover barrel from torque to power position is map-controlled, with load, engine speed and temperature representing the relevant variables. The vacuum reservoir is integrated into the intake manifold module.Vacuum reservoir279_017Lower part of intake manifoldThe lower part of the intake manifold contains four flaps which are driven by the intake-manifold flap motor -V157 via a joint shaft. The potentiometer -G336 integrated into the motor provides the engine control unit -J220 with feedback on flap position. The position of the intake-manifold flaps influences mixture formation and thus emission values. Intake-manifold flap control is classified as an emission-specific system and is monitored by the EOBD. The lower part of the intake manifold is bolted to the fuel rail.279_018 12 Intake air routingThere are two alternatives for air routing with the FSI system. Version 1: The intake-manifold flap is closed and the intake air mass thus routed over the tumble plate into the combustion chamber. This method of air routing is used for stratified charge operation.Throttle valveIntake-manifold flapTumble plate 279_019Version 2: The intake-manifold flap is opened and the intake air mass thus routed over and under the tumble plate into the combustion chamber. This method of air routing permits homogeneous operation. Such a method is referred to as air-controlled combustion with map-controlled in-cylinder flow.279_020 13 Engine managementSystem componentsAir-mass meter -G70 Intake-manifold pressure sender -G71 Intake-air temperature sender -G42 Engine speed sender -G28 Hall sender -G40 Throttle valve control part-J338 Angle senders 1 + 2 -G187, -G188 Accelerator position sender -G79 Accelerator pedal position sender 2 -G185 Brake light switch -F CCS brake pedal switch -F47 Fuel pressure sender -G247 Steering angle sender -G85 Motronic control unit -J220Intake-manifold flap potentiometer -G336 Knock sensors -G61, -G66 Coolant temperature sender -G62 Coolant temperature sender radiator outlet -G83ABS control unit -J104Automatic gearbox control unitOperating and display unit for AC -E87 EGR potentiometer -G212 Lambda probe -G39 Lambda probe after catalyst -G130 Exhaust-gas temperature sender -G235 NOx sender -G295, control unit for NOx sender -J583 Additional input signal14Airbag control unit -J234Control unit with display in dash panel insert -J285Operating and display unit for AC -E87 Fuel pump relay -J17 Fuel pump -G6Injectors, cylinders 1-4 -N30-33Ignition coils 1-4 -N70, -N127, -N291, -N292Throttle valve control part -J338 Throttle valve drive -G186 Motronic current supply relay -J271 Activated charcoal filter solenoid valve -N80Fuel metering valve -N290 Diagnostic connectionIntake-manifold flap motor -V157Camshaft adjustment valve -N205 Map-controlled engine cooling thermostat -F265 EGR valve -N18 Lambda probe heaters -Z19, -Z29Heater for NOx sender -Z44 Additional output signals279_047 15 Engine managementCAN bus interfacesEngine control unit Intake-air temperature Brake light switch Brake pedal switch Throttle valve angle Electronic throttle warning lamp/info Driver input torque Emergency running programs (self-diagnosis info) Accelerator pedal position CCS switch positions CCS specified speed Altitude information Kickdown information Compressor switch-off Compressor ON/OFF Fuel consumption Coolant temperature Clutch pedal switch Idling speed recognition Engine speed ACTUAL engine torques Immobilizer Crash signal Exhaust-gas temperature Gearbox control unit Adaption release Idle regulation Compressor switch-off Specified idling speed SPECIFIED engine torque Emergency running programs (self-diagnosis info) Gearshift active/not active Selector lever position Converter/gearbox protection Torque converter clutch status Current gear/target gear ESP control unit TCS request SPECIFIED TCS intervention torque Brake pedal status ESP intervention Vehicle speed Overrun torque limiting function request Overrun torque limiting function intervention torqueCAN lowCAN highNOx sender NOx saturation (for regeneration)Dash panel insert Self-diagnosis info Vehicle speed Mileage Coolant temperature Oil temperature ImmobilizerSteering angle sender Steering wheel angle (used for pilot control of idling speed and for engine torque calculation based on power steering power requirement)279_06716 Engine control unitUse is made for engine management of the Motronic control unit MED 7.1.1. The designation MED 7.1.1 stands for: M E D 7. 1.1 = = = = = Motronic Electronic throttle Direct injection Version Development statusThe Bosch Motronic MED 7.1.1 incorporates petrol direct injection. With this system the fuel is injected directly into the cylinder and not into the intake manifold.279_048Modes of operationWhereas conventional petrol engines are reliant on a homogeneous air/fuel mixture, lean petrol direct injection engines can be operated with a high level of excess air in the part-throttle range by means of specific charge stratification. There are two main modes of operation with the FSI system: Stratified charge operation in the part-throttle range and homogeneous operation in the full-throttle range. Four more modes of operation are available to round off the FSI concept. These modes of operation are contained in the reading measured value block function.17 Engine managementStratified charge operationTo achieve a stratified charge, injection, combustion chamber geometry and incylinder flow must be optimally matched in addition to satisfying certain prerequisites. Namely: – Engine in corresponding load and enginespeed range – No system faults of relevance to emissions – Coolant temperature above 50 °C – Temperature of NOx storage catalytic converter between 250 °C and 500 °C – Intake-manifold flap closedIntake-manifold flap Tumble plate279_049Throttle valveIn stratified charge operation, the intakemanifold flap completely closes off the lower intake port, thus causing the intake air mass to be accelerated and tumble via the upper intake port into the cylinder.High-pressure injector279_024The tumble effect is further enhanced by the bowl in the piston. At the same time, the throttle valve is opened wide to minimise throttle losses.279_025 18 In the compression stroke, fuel is injected under high pressure (50-100 bar) into the area around the spark plugs just before the ignition point.279_026In view of the relatively shallow injection angle, the fuel spray scarcely comes into contact with the piston crown (so-called "aircontrolled" method).Fuel spray279_027A mixture with good ignition properties forms around the spark plugs and is ignited in the compression phase. In addition, a layer of air forms between the ignited mixture and the cylinder wall after combustion, thus providing insulation and reducing heat dissipation via the engine block.279_028 19 Engine managementHomogeneous operationIn the upper load and engine-speed range, the intake-manifold flap is opened to enable the intake air mass to flow into the cylinder via the upper and lower intake port.279_030In contrast to stratified charge operation, fuel is not injected in the compression phase, but rather in the induction phase, producing a homogeneous charge (14.7:1) in the cylinder.279_03120 Injection in the induction stroke allows far more time to obtain an optimum air/fuel mixture.279_032Combustion takes place in the entire combustion chamber without any insulating air and EGR masses.279_033The advantages of homogeneous operation are the result of direct injection in the induction stroke, in the course of which fuel vaporisation causes some of the heat to be extracted from the intake air mass. Such internal cooling reduces the knock tendency, which means the engine compression ratio can be increased and efficiency enhanced.21 Engine managementStratified charge operation is not possible over the entire map range. The range is restricted due to the fact that greater loads require a richer mixture and the fuel consumption advantage becomes progressively less. Combustion stability also deteriorates with Lambda values less than 1.4, as the mixture preparation time is no longer adequate with increasing engine speeds and the greater airflow turbulence has a negative effect.Homogeneous operation λ = 1 or λ l with 3-way catalytic converter Homogeneous lean operation with λ = 1.5 Charge stratification with adapted in-cylinder flow and optimised EGR strategyEffective mean pressure (bar)Engine speed rpm279_029Maximum fuel economy is achieved in stratified charge operation.22 Self Study Programme Questionnaire279What is your position within the Dealership? Please quote name, telephone number and fax number for reply and queries. ...................................................................................................................................................... Are the descriptions and explanations readily comprehensible? YES NO Page/Section ...................................................................................................................................................... ...................................................................................................................................................... Are the illustrations clear and adequate?A note to all users: This Self Study Programme is intended to familiarise readers with the 2.0 l 110 kW engine with petrol direct injection (FSI).Your opinion matters to us.That is why we would like you to give us your thoughts on and any suggestions for future Self Study Programmes. The following questionnaire is designed to help you do so. Please make use of fax number 0049/841 89 36 36 7 for your suggestions. Thank you for your assistance. Your Service Technology Training TeamYES NO Page/Fig. No. ...................................................................................................................................................... ...................................................................................................................................................... ...................................................................................................................................................... Is enough detail given on the subject matter relevant to your work? YES NO Page ...................................................................................................................................................... ...................................................................................................................................................... ...................................................................................................................................................... Do you consider anything to have been overlooked? NO YESPage/What?...................................................................................................................................................... ...................................................................................................................................................... ...................................................................................................................................................... Should further items be added to this questionnaire? NO YES Which question(s)? ...................................................................................................................................................... ...................................................................................................................................................... ...................................................................................................................................................... Remarks/miscellaneous: ...................................................................................................................................................... ...................................................................................................................................................... Please submit your questionnaire to the following fax number:++49/841 89 36 36 7 Notes23 Engine sub-systemsFuel systemThe fuel system consists of a low and highpressure section. In the low-pressure system, the fuel is conveyed by an electric fuel pump at approx. 6 bar via the filter to the high-pressure pump. The return flow from the high-pressure pump passes directly back to the tank.Fuel pressure sender -G247Pressure relief valveHigh-pressure injector Fuel filterElectric fuel pump -G624 In the high-pressure system, the fuel flows at approx. 40 – 110 bar (depending on load and engine speed) out of the single-plunger highpressure pump into the fuel rail, from where it is distributed to the four high-pressure injectors.The pressure relief valve is designed to protect the components subjected to high pressure and opens as of a pressure of 120 bar. When the pressure relief valve opens, the fuel flows into the supply pipe to the highpressure pump. Double camFuel metering valve -N290approx. 40 - 110 barSingle-plunger highpressure pumpapprox. 6 barACF valveNo pressure Low pressure approx. 6 bar Activated charcoal filter High pressure approx. 40 -110 bar279_034 25 Engine sub-systemsSingle-plunger high-pressure pumpThe single-plunger high-pressure pump with adjustable delivery rate is driven mechanically by the camshaft via a double cam. The electric fuel pump provides the highpressure pump with a supply pressure of up to 6 bar. The high-pressure pump generates the high pressure required in the rail.Fuel metering valve -N290The pressure damper reduces fuel pressure pulsation in the system.Pressure damper 279_035As the piston moves down, fuel flows at a supply pressure of approx. 6 bar from the intank pump via the inlet valve into the pump chamber.279_03726 As the piston moves up, the fuel is compressed and conveyed into the fuel rail on exceeding the prevailing rail pressure. Located between pump chamber and fuel inlet is the switchable fuel metering valve.279_038If the fuel metering valve opens prior to completion of the delivery stroke, the pressure in the pump chamber is dissipated and the fuel flows back into the fuel inlet. A non-return valve between pump chamber and fuel rail stops the rail pressure decreasing when the fuel metering valve opens.To regulate the delivery rate, the fuel metering valve is closed as of pump cam BDC position until a certain stroke is reached. Once the necessary rail pressure has been attained, the fuel metering valve opens to prevent any further increase in pressure in the rail.279_03927 Engine sub-systemsFuel metering valve -N290For safety reasons, the fuel metering valve is designed as a solenoid valve which is open when deenergised. Consequently, the entire delivery volume of the high-pressure pump is pumped back into the low-pressure circuit by way of the open valve seat. Energisation of the solenoid builds up a magnetic field which presses the valve needle connected to the armature into the valve seat. On attaining the rail pressure the fuel metering valve is no longer energised and the magnetic field collapses. The high pressure forces the needle out of the pump chamber and the fuel from the pump delivery chamber which is no longer required can flow back into the low-pressure circuit.Pressure damperFuel metering valve -N290 Fuel inletHighpressure connection Solenoid Armature Pump chamber Valve needleHigh-pressure plunger279_04028 Fuel railThe rail is designed to distribute a defined fuel pressure to the high-pressure injectors and to provide an adequate volume for pressure pulsation compensation. It functions as a high-pressure accumulator and acts as a mount for injectors, fuel pressure sender, pressure limiting valve and high/low-pressure connections.Inlet Return High-pressure pump Fuel pressure senderPressure limiting valve 279_041Intake-manifold flap motor Intake-manifold flap Fuel inlet for injectors279_06429 Engine sub-systemsFuel pressure sender -G247Within the overall system, the function of the fuel pressure sender is to measure the fuel pressure in the rail. The pressure applied is relayed to the engine control unit as a voltage quantity and used for fuel pressure control. The evaluation electronics integrated into the sender are supplied with 5 V. With increasing pressure, the resistance drops and signal voltage rises.HousingConnectorContact link ASICPC board Spacer Sender element Pressure connection 279_042The pressure sender characteristic curve illustrated shows signal output voltage [V] as a function of pressure [MPa].Output voltage5,00 V 4,75 V 4,65 V 4,50 VSender defective Maximum pressure0,50 V 0,30 V 0,25 V 140 barPressur30Minimum pressure Sender defective279_043 High-pressure injectors -N30, -N31, -N32, -N33Fine strainerThe high-pressure injector acts as an interface between the rail and the combustion chamber. The function of the high-pressure injector is to meter the fuel and, by way of atomisation, to create a specific fuel/air mixture in a defined combustion chamber area (stratified charge or homogeneous operation). On account of the difference between rail and combustion chamber pressure, injector actuation causes the fuel to be forced directly into the combustion chamber.SolenoidArmatureThe Teflon seal always has to be replaced after removing the injector (refer to Workshop Manual).Nozzle needleTeflon seal279_044Two booster capacitors integrated into the engine control unit generate the necessary actuation voltage of 50 - 90 V required to ensure a much shorter injection period than with intake-manifold injection.J 220N31N32N30N33279_05031 Engine sub-systemsExhaust systemThe ever increasing demands on exhaust systems as a result of reduced emission limits require an innovative concept specifically adapted to the FSI process.2.0 l FSI engineThis engine features an under-bonnet threeway primary catalytic converter with an upstream and downstream probe for catalytic converter monitoring.Stratified charge operationLambda probeUnder-bonnet 3-way catalytic converter Lambda probeExhaust-gas temperature sender -G235The sender is located directly upstream of the NOx storage catalytic converter. It transmits the exhaust-gas temperature to the engine control unit for calculation of the temperature in the NOx storage catalytic converter. The engine-management system requires this information – For switching to stratified charge operation, as nitrogen oxides can only be stored in the NOx catalytic converter at temperatures between 250 and 500 °C – To remove sulphur deposits from the NOx storage catalytic converter. This is only possible at catalytic converter temperatures above 650 °C with a rich mixture and is achieved by way of switching to homogeneous operation and ignition retard.32 Exhaust gas treatment systemWith a lean mixture composition, the conventional three-way catalytic converter exhibits a high conversion rate for CO and HC on account of the high residual oxygen content of the exhaust gas. The NOx conversion rate drops however if CO and HC concentrations are too low. Use is made of the NOx storage catalytic converter to reduce the increased NOx component in lean operation (stratified charge operation).Engine control unitCAN wireControl unit CO = Carbon monoxideNOx HC Temperature sender NOx sender= Nitrogen oxides = HydrocarbonsNOx storage catalytic converter279_051NOx storage catalytic converterThe design of this converter corresponds to that of the three-way catalytic converter. The wash coat is however additionally provided with barium oxide to permit buffer storage of nitrogen oxides at temperatures between 250 and 500 °C through nitrate formation. In addition to the desired nitrate formation, the sulphur contained in the fuel is always stored as well.33The storage capacity is however limited. The engine control unit is informed of saturation by the NOx sender and the enginemanagement system then takes appropriate action to regenerate the NOx storage catalytic converter. Engine sub-systemsRegeneration phasesThese are regulated by the engine control unit and are designed to extract the nitrogen oxides and sulphur. In this process, nitrogen oxides are converted into non-toxic nitrogen and sulphur into sulphur dioxide.Nitrogen oxide regenerationThis takes place as soon as the concentration in the NOx storage catalytic converter exceeds the level specified in the engine control unit. The engine control unit effects switching from stratified charge to homogeneous operation. This causes the temperature of the NOx storage catalytic converter to increase. The nitrates formed thus become unstable and decompose under reducing ambient conditions. The nitrogen oxides are converted into harmless nitrogen. The storage catalytic converter is thus emptied and the cycle recommences.Stratified charge operation approx. 2 sec. 60-90 sec.Homogeneous operation λ 1Stratified charge operation279_06234 Sulphur regenerationThis takes place in separate phases, as the sulphates formed are more chemically stable and therefore do not decompose in the course of nitrogen oxide regeneration. The sulphur also occupies storage space, with the result that the storage catalytic converter becomes saturated at ever shorter intervals. As soon as the specified value is exceeded, the engine-management system reacts by implementing the following action: – Switching from stratified charge to homogeneous operation for approx. two minutes and – Ignition retard This increases the catalytic converter operating temperature to above 650 °C, which causes the sulphur stored to react to form sulphur dioxide SO2.Stratified charge operation 2 minutesTDCHomogeneous operationTDCIgnition RETARDStratified charge operationTDC279_063With low-sulphur fuels, the desulphurisation interval is correspondingly longer, whereas high-sulphur fuels necessitate more frequent regeneration phases.Driving at high engine speed under heavy load automatically leads to desulphurisation.35 Engine sub-systemsNOx sender -G295The sender is located directly downstream of the NOx storage catalytic converter. The NOx sender operates in a manner similar to the wide-band Lambda probe. In the first pump cell, the oxygen content is adapted to a constant, roughly stoichiometric value (14.7 kg of air : 1 kg of fuel) and the Lambda value picked off via the pump flow. The gas flow is then routed via a diffusion barrier into the O2 measurement cell, where reducing electrodes separate the nitrogen oxides into oxygen (O2) and nitrogen (N2). The NOx concentration is determined by way of the pump oxygen flow.Platinum electrode NOx-active electrode O2 measurement cell O2 pump cell O2-selective electrode YS-ZrO2Diffusion barrier Heater 279_065Control unit for NOx sender -J583This is located on the underside of the vehicle next to the NOx sender. It conditions the sender signals and transmits the information to the engine control unit by way of the drive CAN bus. The rapid data transfer enables the engine control unit to establish nitrogen-oxide saturation more effectively and to initiate regeneration of the storage catalytic converter.Exhaust-gas temperature sender -G235This is located directly upstream of the NOx storage catalytic converter. The exhaust-gas temperature sender permits monitoring and control of the operating range of the NOx storage catalytic converter with respect to temperature to ensure optimum NOx conversion.Al2O3 substrate Connection pads InsulationIn addition, the exhaust-gas temperature sender is used for thermal diagnosis of the primary catalytic converter, to support the exhaust-gas temperature model and to protect components in the exhaust system.Perforated housing Sender element in platinum thin layer Carrier material279_06636 Exhaust-gas recirculationThe engine features external exhaust-gas recirculation. The exhaust gas is extracted by way of a connecting pipe at the primary catalytic converter. The volume of exhaust gas calculated precisely by the engine control unit is fed in via the exhaust throttle valve, which is driven by an electric motor. The position of the exhaust throttle valve is monitored by a potentiometer. It permits calculation of the exhaust gas volume and is used for self-diagnosis. The exhaust gas returned to the combustion chamber is used to lower the peak combustion temperature and thus reduce nitrogen oxide formation.Exhaust-gas recirculation valve -N18Connecting pipe279_055The exhaust-gas recirculation valve -N18 takes the form of a module and comprises the following components: – Throttle valve – Electric motor with exhaust-gas recirculation potentiometer -G212Exhaust-gas recirculation takes place in stratified charge/homogeneous operation at up to approx. 4000 rpm with medium load. There is no EGR at idle.Exhaust-gas recirculation potentiometer -G212Throttle valveElectric motor 279_045Adaption by way of "basic setting" function must always be performed after replacing exhaust-gas recirculation valve and/or engine control unit.37 EngineBlock diagramMotronic ME7.1.1 F36 Clutch pedal switch F47 Brake light switch F265 Map-controlled engine cooling thermostat G2 G6 G28 G39 G40 G42 G61 G62 G66 G70 G71 G79 G83 G130 G185 G186 G187 G188 G212 G235 G247 G295 G336 J17 J271 J338 J583 N18 N30 N31 N32 N33 N70 N80 Coolant temperature sender Fuel pump Engine speed sender Lambda probe Hall sender Intake-air temperature sender Knock sensor 1 Coolant temperature sender Knock sensor 2 Air-mass meter Intake-manifold pressure sender Accelerator position sender Coolant temperature sender - radiator outlet Lambda probe after catalyst Accelerator pedal position sender 2 Throttle valve drive Throttle valve drive angle sender 1 Throttle valve drive angle sender 2 Exhaust-gas recirculation potentiometer Exhaust-gas temperature sender Fuel pressure sender NOx sender Intake-manifold flap potentiometer Fuel pump relay Motronic current supply relay Throttle valve control part Control unit for NOx sender Exhaust-gas recirculation valve Injector, cylinder 1 Injector, cylinder 2 Injector, cylinder 3 Injector, cylinder 4 Ignition coil 1 with output stage Activated charcoal filter solenoid valve N127 N205 N239 N290 N291 N292 P Q V274 Ignition coil 2 with output stage Camshaft adjustment valve Intake-manifold flap changeover valve Fuel metering valve Ignition coil 3 with output stage Ignition coil 4 with output stage Spark plug connector Spark plugs Fan for control unitJ338 G188 G187 V157 G336 N18 G212 G247 G71 G42 G83 G62 G2 G40 G66 G61 G28 F47 F36 G130 G39 G70Colour code = Input signal = Output signal = Positive supply = Earth = CAN bus = Bidirectional1 2 3 4 5 6M M MN31N32N30N33Additional signals 1 2 3 4 5 6 K-wire CAN High/drive CAN Low/driveN70N127N291N292G79G185 P M M ZYL 1 Q G6 J17 J271 P ZYL 3 Q P ZYL 4 Q P ZYL 2 QAlternator test signal Radiator fan PWM TD signal (Multitronic only)G235F265G295J583 V274 N239 N80 N290 N20538 ServiceSpecial toolsT 10133/1 T 10133/2279_072279_057T 10133/3T 10133/9279_073279_058T 10133/5T 10133/6T 10133/7T 10133/8279_070279_068279_069279_059T 10133/4279_07139 Notes40 All rights reserved. Subject to technical modification. AUDI AG Department I/VK-35 D-85045 Ingolstadt Fax 0841/89-36367 240.2810.98.20 Technical status as at 12/01 Printed in Germany279