TECHNICAL DOCUMENTATION
SSP 291 6-speed Automatic Gearbox 09G

This PDF is currently unavailable.
Read document text
Service Training6-speed Automatic Gearbox 09GSelf-Study Programme 291Dynamics and economyThe 6-speed automatic gearbox 09G sets new standards in the segment of transversely mounted multi-step automatic gearboxes • Low weight • Wide ratio spread*Brief technical description6-speed automatic gearbox using the Lepelletier planetary gear set concept. The wide ratio spread* of 6.05 provides flexibility in use (sport or economy mode). Only five gear shifting components are required. Highly compact, lightweight and powerful.• Compact gearbox dimensions • High shifting speed • High level of shift comfortThere are three gearshift modes to choose from: sport program and manual gear selection by tiptronic. In triponic mode, it is possible to start in second gear.* you will find an explanation of the terms/ paragraphs marked with an asterisk as of page 72 This Self-Study program gives general descriptions of the 09G gearbox and shows the special features in combination with the Audi A3 ‘04 and Audi TT.291_117The basics for this Self-Study Programme are covered in the multimedia training course "Power Transmission 2" and in the previously published self-study programmes on multi-step automatic gearboxes. The Self-Study Programme is not a Repair Manual! The values given are intended as a guideline only and refer to the software version valid at the time of publication of the SSP. For maintenance and repair work, always refer to the current technical literature.ReferenceNoteContentsGeneralIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05 Sectional view of gearbox 09G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06Gearbox peripheryGear selector of the Audi A3 ‘04 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08 Selector lever locks on the Audi A3 ‘04 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Ignition key removal lock on the Audi A3 ‘04 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Gear selector of the Audi TT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Tiptronic steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Gearbox subassembliesTorque converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Torque converter lock-up clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Oil supply/lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Planetary gear/shifting components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Hydraulic control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Shift logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Description of gears/torque curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Parking lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Gearbox controlFunction diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Automatic gearbox control unit J217 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Interfaces/auxiliary signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 CAN information exchange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Distributed functions in the Audi A3 ‘04/Dynamic Shift Program DSP . . . . . . . . . . . . . . . . . . . . . . . . . 68 Tiptronic gearshift strategy/sport program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69ServiceEmergency running/towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Special tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71GlossaryTerms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72GeneralIntroductionThe 6-speed automatic gearbox 09G is used in the Audi A3 ‘04 and Audi TT. The gearbox is a conventional multi-step automatic with hydrodynamic torque converter and electrohydraulically operated planetary gear. The 09G gearbox is developed and manufactured by the Japanese transmissions specialist AISIN AW CO., LTD. In association with Audi's development engineers, the gearbox has been adapted to suit the characteristics specific to each vehicle and engine*. Compared to the predecessor gearbox (model 09A), the weight of gearbox 09G has been reduced by 19.5 kg from 102 kg to 82.5 kg, even though a sixth gear has been added. This was achieved by using the Lepelletier gear set concept and through selective optimisation of component parts. With the additional gear, the spread* has been increased to 6.05. This figure surpasses that of all front/transversely mounted multi-step automatic gearboxes currently on the market and matches the ratio spread of variable automatic gearboxes. The Lepelletier gear set concept, as found previously in the Audi A8 gearbox 09E, is used in gearbox 09G. The advantage of the Lepelletier gear set concept is its simple, space-saving and low-weight design. It combines a simple planetary gear train with a Ravigneaux gear seat further down. This allows a harmonious 6-speed transmission to be achieved using only five gear shifting components. The six forward gears and reverse gear are engaged by three multi-plate clutches and two plate brakes.Reference For further information on the Lepelletier gear set concept, refer to SSP 283.291_002291_0014SpecificationsDeveloper/manufacturer DesignationsAISIN AW CO, LTD Japan Manufacturer: TF-60SN Audi AG: AQ250-6F Service: 09G electrohydraulically controlled 6-speed planetary gear (multi-step automatic gearbox) with hydrodynamic torque converter and slipcontrolled converter lock-up clutch for frontwheel drive and transverse installations hydraulic control unit integrated in the oil sump with external electronic control unit Dynamic Shift Program DSP with separate sport program in "Position S" and the tiptronic shift program for manual gearshifts (optionally available with tiptronic steering wheel)Gearbox typeControlTorque in Nm Ratios: Planetary gear (for engine codes GSY 1.6 l and GJZ 2.0 l FSI)up to over 300 Nm depending on type First gear Second gear Third gear Fourth gear Fifth gear Sixth gear Reverse gear 4.148 2.370 1.556 1.155 0.859 0.686 3.394Idler Final drive i constant* Spread* (GSY/GJZ) ATF specification Capacity Weight in kg Overall length in mmZ52/49 1.061 (GSY and GJZ) Z61/15 4.067 (GSY) or Z58/15 3.867 (GJZ) 4.316 (GSY) or 4.102 (GJZ) 6.05 G 052 025 A2, Esso JWS 3309 7.0 litre (refilling) lifetime filling approx. 82,5 approx. 350The gearbox in the Audi A3 ‘04 (with 1.6 l FSI and 2.0 l FSI engines) is configured as a so-called 5+E gearbox. Max. speed is reached in fifth gear. Sixth gear is an overdrive gear which reduces engine revs, improves driving comfort and increases fuel economy.The gearbox in the Audi TT is configured as a so-called sport gearbox. Max. speed is attained in sixth gear. Sixth gear provides closer ratios and enhanced driving dynamics.Reference * You can find an explanation of the marked terms/paragraphs as of page 72.5GeneralSectional view of gearbox 09G291_030 6Components overview:ATF heat exchangerMulti-function switch F125Automatic gearbox control unit J217 Connector for sensorsConnector for solenoid valves291_116Bottom view of gearboxSensors 291_037Hydraulic control (valve body) with solenoid valvesN91 N93 N89N88 N92291_112N282Solenoid valvesN283N90 A2291_038Legend to sectional view of gearbox Hydraulic parts, hydraulic control, ATF Components of the shifting components Cylinders, pistons, air sensor plates Housings, screws, boltsComponents of the planetary gear setsShafts, gearsElectrical componentsMulti-plate clutches, bearings, washers, circlips Plastics, seals, rubber, washersInput signalOutput signal7Gearbox peripheryGear selector of the Audi A3 ‘04Selector gate cover/selector lever gateLEDs PCBLEDs291_010Selector gate cover 291_009 Selector lever gateThe "D–S" gear selector, as found in higher vehicle classes, is used in combination with the new automatic gearbox variants.On the selector lever gate PCB, there are LEDs for illuminating the various selector lever and tiptronic positions on the selector gate cover. These LEDs are activated by the selector lever sensors integrated in the gear selector.Gear selectorSelector lever sensors with tiptronic switch F189PRNDS + F319LegendN110F319 J217Selector lever locked in position P switch Automatic gearbox control unit Selector lever lock solenoid signal to steering column electronics control unit J527+-123 45 67 89 10N110 PKL.30a KL.15aJ21748 29 11 37 KL.31 KL.58d P KL.31Output Input291_1028Gear selector/designSelector lever locked in position P switch F319Selector lever lock solenoid N110 Hall sensors for the Tiptronic switch F189291_011A291_011 Selector lever cable Hall sensors for selector lever position Selector lever sensors with Tiptronic switch F189Integrated in the gear selector of the Audi A3 ‘04 are the sensors for the selector lever positions and the tiptronic function (F189). The various selector lever positions are determined by Hall sensors which are operated by permanent magnets and processed by the evaluation electronics. The evaluation electronics activate the LEDs on the selector gate cover according to the selector lever position.The signals from the tiptronic switch F189 are also evaluated by the selector lever sensors and transferred to the gearbox control unit through a separate interface in the form of a frequencymodulated square-wave signal (FMR signal).Reference You can find further information about this subject on page 50 of this Self-Study Programme.9Gearbox peripherySelector lever locks on the Audi A3 ‘04Pawl for locking in "P" positionSelector lever lock solenoid N110291_015a Emergency release mechanismLocking pin of N110 291_022Pawl for locking in "N" positionThe selector lever lock function is new: Basically, there is a distinction to make between, first, P/N lock application when driving or with the ignition ON and, second, locking of the selector lever in the "P" position with the ignition key removed (P-lock). The P-lock function was previously performed by the steering lock by means of a gear selector cable. The electromechanical ignition key removal lock has eliminated the need for a cable pull and a mechanical connection between the steering lock and gear selector. The P-lock function is carried out by the locking pin of the selector lever lock solenoid N110. The selector lever pawls and the locking pin kinematics of N110 are such that the P-lock can be applied regardless of whether solenoid N110 is energised (position "N") or deenergised (position "P").Emergency releaseBased on the functional principle, the selector lever remains locked in position "P" if malfuncting occurs or the voltage supply fails (e.g. flat battery), see Fig. 088. The selector lever lock has an emergency release mechanism which enables the vehicle to be moved (e.g. towed).10Selector lever position "P" locked: Solenoid N110 is deenergised; the locking bolt is engaged by spring pressure in the park (P) pawl. The selector lever is locked. Emergency release The emergency release mechanism can be accessed after removing the gearshift console cover (see Operating instructions). When the emergency release is operated, the locking bolt of the N110 is forced out of the "P" (park) pawl against the pressure of the spring. The selector lever can now be moved out of the park ("P") position.Locking boltOperating device Emergency releaseEmergency release mechanismSpring291_088- +Selector lever position "P" unlocked: Solenoid N110 is energised by J217; the locking bolt is pulled out of the park ("P") pawl against the pressure of the spring. The selector lever lock is released.291_087Selector lever position "N" locked: If the selector lever is in the "N" position for longer than 2 sec. with the ignition on, then solenoid N110 will be energised by J217. The locking bolt is pressed into the "N" (neutral) position against the pressure of the spring. The N lock is not activated at road speeds of higher than approx. 5 kph.- +291_089Selector lever position "N" unlocked: The N110 is deenergised when the brake is applied and when the ignition is OFF. The locking bolt is pulled out of the neutral ("N") pawl by the pressure of the spring.291_11011Gearbox peripheryIgnition key removal lock Audi A3 ‘04Ignition key with drawal lock solenoid N376291_004Steering column electronics control unit J527291_003The ignition key withdrawal lock is implemented in such a way that the ignition key cannot be fully turned anticlockwise to the end position (withdrawal position) when the selector lever is not in the "P" position. On the Audi TT, this function is performed mechanically by the steering lock by means of a cable pull (locking cable). The ignition key withdrawal lock function in the Audi A3 ’04 is carried out electromechanically by means of the ignition key withdrawal lock solenoid N376. Solenoid N376 is activated by the steering column electronics control unit J527. For this purpose, J527 requires the information "selector lever position P locked".This information is acquired by multi-function switch F125 and sent to via CAN bus to control unit J527 by gearbox control unit J217. At the same time, the microswitch F319 selector lever locked in position P switch is active in the gear selector. The signal from this switch is also evaluated by control unit J527 and checked for plausibility against the CAN information from J217.12Selector lever locked in position P switch F319Selector lever lock solenoid N110Selector lever sensors with Tiptronic switch F189291_005The F319 is designed as an NC contact. Switch F319 is operated if the lock button on the gear shift knob is released in selector lever position "P" (circuit state "open”).The switch is closed in selector lever positions "R", "N", "D", "S" and tiptronic (and in "P" with lock button pressed).Gear selectorSelector lever sensors with Tiptronic switch F189LegendPRNDS + F319F319 J217Selector lever locked in position P switch Automatic gearbox control unit signal for ignition key withdrawal lock (to J527 steering column electronics control unit)+-P9 10123 45 67 8KL.30a J217 217 KL.15a KL.31 KL.58d P KL.31Output Input291_105Note To improve diagnosis of the F319, two resistors are connected in series to switch F319.13Gearbox peripheryThe ignition key withdrawal lock functionIf the selector lever is not in the "P" (park) position, the ignition key withdrawal lock solenoid N376 will be energised by J527. The locking bolt of the N376 is forced into the steering lock against the pressure of the spring. As long as the N376 is energised (locking bolt retracted), the ignition lock cannot be turned to the withdrawal position. The ignition key cannot be removed.Ignition key withdrawal lock solenoid N376291_006Locking bolt guide Locking bolt in "energised" positionN376 "energised"J527Retaining lug-+Locking boltF319291_019 N376Locking bolt guideKey position: "ignition OFF" Ignition key withdrawal lock appliedLegend F319 J527 N376 Selector lever locked in position P switch Steering column electronics control unit Ignition key withdrawal lock solenoid14With the ignition OFF and in the "P" position of the selector lever (button on selector lever is not pressed), the J527 switches off the solenoid N376. As a result, the locking bolt is pulled back by the spring in the N376. The ignition key can now be turned to the withdrawal position and removed.N376 "not energised"J527-+F319291_018 SpringN376Key position: "withdrawal position" Ignition key withdrawal lock releasedNote As long as the selector lever out of the "Park" position after ignition off, the J527 energises solenoid N376. If the vehicle is parked for an extended period of time with the selector lever out of the "P" position, this will cause battery to become discharged in the long term.15Gearbox peripheryGear selector of the Audi TTThe gear selector of the Audi TT is identical in function and design to the selector of the Audi A3 Typ8L. When the ignition key is removed, the P-lock and the ignition key withdrawal lock are operated in a conventional manner by means of a cable pull (locking cable).Selector lever sensors with tiptronic switch F189Selector lever lock solenoid N110291_100CLocking cableShift cable291_100Reference For information on the function of tiptronic switch F189, please refer to page 52 of this Self-Study Programme.16tiptronic steering wheelIn combination with the tiptronic steering wheel, the "Tiptronic" function is also available in selector lever position "D" or "S". The tiptronic function is selected by pressing one of the two tip-shift paddles on the steering wheel (selector lever in position "D" or "S"). The system then switches to tiptronic mode for approx. 8 sec. All gears can be selected within the permissible engine speed range. It is possible to skip gears, e.g. to shift down from sixth to third, by pressing the shift paddle several times. The system returns to normal automatic operation approximately 8 sec. after the last tip shift request. Special feature: the countdown of approx. 8 sec. until return to normal automatic operation is discontinued while the vehicle is cornering or in overrun. The countdown time is extended depending on the vehicle’s driving dynamics. However, the system will switch from tiptronic mode to automatic mode within 40 seconds at the latest. In the Audi A3 ‘04 the shift pulses are transferred from the tiptronic buttons or multi-function buttons to the steering column electronics control unit J527 via LIN data bus.291_013 4-spoke multifunction steering wheel with tiptronic (Audi A3) Tip-shift paddle3-spoke sport steering wheel with tiptronic (Audi A3) Tip-shift paddle291_0123-spoke sport steering wheel with tiptronic (Audi TT) Tip-shift paddleNote In export vehicles for the USA, the tiptronic steering wheel function is disabled in selector lever position "D" or "S".291_12417Gearbox peripheryFunction in the Audi A3 ‘04The shift pulse from the tiptronic switches E389 (earth signal) is evaluated by multifunction steering wheel control unit J453 and sent via LIN data bus to the steering column electronics control unit J527. The J527 sends the information by convenience CAN bus to data bus diagnostic interface J533 (gateway). The data is sent from J533 to the driveline CAN bus, and thereby to the automatic gearbox control unit J217.Multifunction tiptronic steering wheel with multifunctional capability in the Audi A3 ‘04Driveline CAN busJ217J533Convenience CAN busCAN nodeE389 Tip + Tip E221 MODEJ527Coil springE389 Tip + Tip -E22131 LIN 15J45331 58 PWM Tip Tip +Tip + Tip 58 PWM 31291_014Legend E221 E389 J217 J453 J527 J533 Operating unit in steering wheel Tiptronic switch in steering wheel Automatic gearbox control unit Multi-function steering wheel control unit Steering column electronics control unit Data bus diagnostic interface (gateway) LIN 58 PWM LIN single-wire bus system Pulse-width modulated dimming of the switch lightOutput Input18Multifunction tiptronic steering wheel without multifunctional capability in the Audi A3 ‘04J217Driveline CAN busJ533CAN node Convenience CAN busJ527Coil springTip -E389Tip +E38931 LIN15J45331 Tip -Tip +31291_115Tiptronic steering wheel in the Audi TTE389 Tip + Tip J21713 14E389 Tip + Tip -Kl. 58s Kl. 31Coil spring291_10119Gearbox subassembliesTorque converterSprocketDrive slotsTorque converter hubTorque converter lock-up clutch291_023The starter sprocket is welded onto the torque converter housing, and therefore is a component part of the torque converter. This construction detail contributes to the compact design of the gearbox. The torque converter hub is mounted on the ATF pump by means of a low-friction bearing (torque converter bearing). The ATF pump is driven via the drive slots in the torque converter hub. This can be adapted to the characteristics of various engines by using different torque converter types, whereby the torque conversion characteristic (torque multiplication) is adapted. For example: factor 1.95 for gearbox GJZ or factor 2.20 for gearbox GSY.291_024Torsion damper20Mounting instructionsTorque converter installation dimensionPinionRing gearDriverDrive slotTorque converter bearingATF pump291_091Torque converter hub291_092Note When mounting the torque converter and before installing the gearbox, special care must be taken to ensure that the ATF pump drivers engage correctly into the drive slots in the torque converter hub. This can be checked by measuring the installation position of the torque converter (refer to Workshop Manual).Note Care must always be taken to ensure that the bushing press fits are correctly installed between the engine and gearbox. Failure to fit bushing press fits will cause irreparable damage to the low-friction bearing and the torque converter hub due to the offset between the engine and the gearbox.21Gearbox subassembliesTorque converter lock-up clutchDesignThe torque converter has a torque converter lock-up clutch with built-in torsion dampers. The torsion dampers reduce torsional vibration when the torque converter lock-up clutch is closed. This allows the operating range "torque converter lock-up clutch closed" to be extended. Basically, a distinction is made between a distinction is made between the following functional states: – converter lock-up clutch - open – converter lock-up clutch - controlled operation – converter lock-up clutch - closed During normal vehicle operation, the torque converter lock-up clutch is operated from third gear.Torque converter lock-up clutch Torsion damper291_025Reference For more detailed information about the basic design and function of the torque converter lock-up clutch, refer to SSP 283.22Controlled operationThe torque converter lock-up clutch is operated with a minimum of slip at defined operating points (controlled operation). Controlled operation offers, first, better fuel economy than operation with the torque converter lock-up clutch open and, second, better ride comfort than operation with the torque converter lock-up clutch closed.Torque converter lock-up clutch operating ranges in "D"converter lock-up clutch - open Engine loadconverter lock-up clutch - controlledconverter lock-up clutch - closedRoad speed 291_026In tiptronic mode and in the "S" programme, the converter lock-up clutch is closed at the earliest possible moment. The positive, direct connection between the engine and gearbox emphasises the sporty driving feel. In the hill-climbing program, the torque converter lock-up clutch is closed in second gear.In the Hotmode programme, the converter lock-up clutch is operated in a controlled manner, but is closed early. This reduces the heat transfer caused by converter lock-up clutch friction or hydrodynamic power transmission. Hotmode programme: see page 6023Gearbox subassembliesOil supply/lubricationATF (Automatic Transmission Fluid)The stringent requirements with regard to shift quality, functional reliability and ease of maintenance place extremely high demands on the ATF, too. The ATF is a key factor in determining the friction coefficient of the clutches/brakes. For this reason, the ATF is developed parallel to design and testing. It therefore stands to reason that the 09G gearbox uses a special advanced ATF type. Use of the prescribed ATF is therefore a requirement for proper functioning of the gearbox. The 09G gearbox is lubricated with ATF G 052 025 (Esso JWS 3309). The gearbox and ATF type are adapted to match each other. Only the approved ATF type should be used. The filling system (V.A.G 1924) must be free of foreign ATF residues. The planetary gear, final drive and differential share the same oil supply. There is no need to change the ATF within the designated maintenance intervals (lifetime filling).ATF pumpNote The ATF is red-coloured. There is a danger of mixing up with other ATF oils. A separate filling system should therefore be used for each ATF.291_027A24ATF pumpOne of the key components of an automatic gearbox is the ATF pump. The gearbox does not function correctly without an ample supply of oil. The ATF pump is designed as an internal gear pump (Duocentric pump). It is driven directly by the engine (engine speed) via the torque converter housing and the torque converter hub. Two drive slots in the torque converter hub engage the pinion drivers. The torque converter hub is mounted on the pump housing using a low-friction bearing.Note During installation of the torque converter and before installing the gearbox, special care must be taken to ensure that the ATF pump drivers engage correctly in the slots in the torque converter hub. This can be checked by measuring the installation position of the torque converter (refer to Workshop Manual).Ring gearPinionDriver291_027BNote Also, care must always be taken to ensure that the bushing press fits are correctly fitted between the engine and gearbox. Failure to fit bushing press fits will cause irreparable damage to the low-friction bearing and the torque converter hub due to the offset between the engine and the gearbox.25Gearbox subassembliesATF coolingThe ATF is cooled by an ATF cooler (coolant-oil heat exchanger) which is directly flanged onto the gearbox and integrated into the engine's cooling circuit. The direct connection between the ATF cooler and the gearbox allows cooling capacity to be adapted more easily. The elimination of ATF lines greatly reduces the number of potential fault sources with regard to leak-tightness.Engine coolant circuitDistributor pipe in the Audi TT ATF cooler291_028AATF circuit291_028The "closed-circuit oil supply" makes it easier to fill the gearbox with ATF and check the oil level. There is no need to disconnect ATF lines when removing and installing the gearbox. In this way, ingress of dirt into the gearbox is minimised. The ATF cooler is included in the scope of supply of the gearbox. It is no longer necessary to clean the cooler and the oil lines when replacing a damaged gearbox.For flow reasons, a distributor pipe is installed in the supply line to the ATF heat exchanger in the Audi TT.Note Do not install the distributor pipe in the return line of the ATF heat exchanger.26Planetary gear/gear shifting componentsK3 K1 B1 F B2 K2291_032The Lepelletier planetary gear set concept is used in the 09G planetary gear. Thanks to the special design of the Lepelletier planetary gear train, only fix shifting components are required to select the six forward gears and reverse gear. The gear shifting components (clutches/brakes) allow gear-shifting under load without any interruption in engine drive power. The five gear shifting components are: – three planetary multi-plate clutches K1, K2 and K3 – two fixed plate brakes B1 and B2The clutches have a dynamic pressure equalisation feature which provides control response independent of engine speed. Clutches K1, K2 and K3 transmit the engine torque to the planetary gear. Brakes B1 and B2 and the freewheel multiply the engine torque at the gearcase. All clutches and brakes are activated indirectly by the electrical pressure control valves. The freewheel F, likewise a gear shifting component, is positioned parallel to brake B2. During automatic operation, the freewheel assumes the function of B2. Freewheel F simplifies electrohydraulic gearshift control when selecting gears and while shifting from first to second or second to first.Reference You can find further details in SSP 283 (from page 50) and in the multimedia training course "Power Transmission 2".27Gearbox subassembliesComponents - planetary gears/shifting componentsWK P1 K1 B1 F B2 K2P2 PT2 S2 S3291_031PT1H1S1H2P3Schematic representation of diagram section with grey background 291_031F B1B2K2WK K3H2 P2 K1 H1 PT2 S2PT1P3P1 S1 S3291_10728Primary planetary gear train Component: H1 P1 S1 PT1 ring gear 1 planetary gears 1 sun gear 1 planet carrier 1 connected to: turbine shaft (input)/clutch K2 power transmission in planetary gear train fixed clutches K1 and K3Secondary planetary gear train Component: H2 P2 P3 S2 S3 PT2 ring gear 2 planetary gears 2, long planetary gears 3, short sun gear 2, large sun gear 3, small planet carrier 2 connected to: output power transmission in planetary gear train power transmission in planetary gear train clutch K3/brake B1 clutch K1 clutch K2/brake B2/freewheel FClutches, brakes, freewheel Component: K1 clutch 1 connected to: Planet carrier PT1 (primary gear train) is connected to small sun gear S2 (secondary gear train). Engaged in first, second, third and fourth gear. Turbine shaft (input) is connected to planet carrier PT2 of the secondary planetary gear train. Engaged in fourth, fifth and sixth gear. Planet carrier PT1 (primary gear train) is connected to large sun gear S2 (secondary gear train). Engaged in third, fifth and reverse gear. Holds in place the large sun gear S2 (secondary gear train). Engaged in first gear (with engine brake) and reverse (R) gear. Holds in place planet carrier PT2 (secondary gear train). Engaged in first gear (with engine brake) and reverse (R) gear. Holds in place planet carrier PT2 (secondary gear train) in the opposite direction to the engine. Is used for accelerating in first gear (not as engine brake).K2-clutch 2K3-clutch 3B1-brake 1B2-brake 2F-freewheelConverter lock-up clutch29Gearbox subassembliesHydraulic controlValve bodyThe clutches and brakes (shifting components) are controlled by the valve body by means of hydraulically operated valves (so-called shift valves). The shift valves are controlled by electromagnetic valves, which in turn are activated by automatic gearbox control unit J217. In addition to the shifting components, the valve body controls the torque converter lock-up clutch and regulates the various pressures inside the gearbox (e. g. primary pressure, control pressure, torque converter pressure and lubricating pressure). It is to a large extent responsible for oil supply, and therefore proper operation of the gearbox. The valve body houses the following components: – the mechanically operated gear selector valve – the hydraulically controlled switch valves – two electrically controlled solenoid valves (3/2-way valves) – six electrically controlled pressure control valves (modulating valves) – two pressure switches (hydraulic pressure sender) and – the gearbox oil temperature sensorAutomatic gearbox control unit J217Valve body291_053291_037Automatic gearbox hydraulic pressure sender -2- G194 (pressure switch)N91 N93 N89 N89Shift solenoids OPEN-CLOSE valvesN88 N92Electronic pressure control valves (EDS)Automatic gearbox hydraulic pressure sender -1- G193 (pressure switch)N282N283Gear selector valveN90A2Installation location for gearbox oil temperature sensor G93 (component part of wiring harness) Bottom view of valve body291_03930Electromagnetic valvesIn the case of electromagnetic valves, a distinction is made between shift solenoids with two switch positions (OPEN-CLOSE) and electrical pressure control valves (referred to as EDS or modulating valves). The shift solenoids (N88/N89) are so-called 3/2 valves or OPEN-CLOSE valves. 3/2 valve means the valves has 3 terminals and 2 switch positions (open/closed or OPEN-CLOSE). The shift solenoids are used for switching the hydraulic valves. The electronic pressure control valves (EDS) convert an electrical current to a proportional hydraulic control pressure. Two types of EDS valve are installed. EDS valves with a rising characteristic curve increase the pilot pressure (P) with rising control current (I) - deenergised - zero pilot pressure (0 mA = 0 bar). EDS valves with a falling characteristic curve reduce the pressure with rising pilot current - deenergised max. pilot pressure.EDS with rising characteristic curve Shift solenoids OPEN-CLOSE valvesN91 N93 N89 N89N88 N92291_122N282EDS with falling characteristic curveN283N90 A2291_121 291_039Effects of fault: If the self-diagnosis detects a faulty electromagnetic valve, the emergency mode will usually be activated. You can find more information about the emergency mode on page 70. Electrical and mechanical faults have very different effects due to the complexity of the electrohydraulic control system. They may affect for instance only the faulty system in question (e.g. the torque converter lock-up clutch in the case of N91), but can also lead to activation of the emergency mode if safe operation can no longer be guaranteed. If the EDS N93 fails, the gearbox operates at maximum system pressure. This can result in harsh engagement when shifting from P or N to D/S or R and during all gearshifts. If the EDS N91 fails, the torque converter lock-up clutch cannot be activated and therefore remains open.31Gearbox subassembliesShift logicSolenoid logic Gear shifting component logic3/2 valvesElectronic pressure control valves (EDS)Clutches, brakes, freewheelN89P N Reverse (R) gear First gear Second gear Third gear Fourth gear Fifth gear Sixth gear T/Z T/Z T/Z TN88N92N282N90N283 N93N91K1K2K3B1B2FTTZ Z Z Z291_036Functional assignments of the solenoid valvesN90 controls clutch K3, N91 controls the torque converter lock-up clutch, N92 controls clutch K1, N93 controls the primary pressure/system pressure N282 controls clutch K2 and N283 controls brake B1. Solenoid valves N88 and N89 control shifting of gears 4 to 6 and are activated (energised) temporarily and alternately during gearshifts. In addition, solenoid valves N88 and N89 control brake B2 in first gear - tiptronic mode (for the engine brake).Legend for solenoid valve logic: Solenoid valve is not activated (current: approx. 100 mA) or Gear shifting component open Solenoid valve is activated Solenoid valve is activated (current: approx. 1.0 A) Corresponding clutch closed Corresponding brake closed Freewheel locked Solenoid valve is energised differently depending on operating stateT Note The function is inverse to applied current, since EDS N92, N93, N282 and N283 have a falling characteristic curve. This means that the respective shifting component is operated if the EDS is not activated.-in tiptronic mode (first gear with enginebrake) solenoid valves are activated for a short time only during gearshiftsZ -32Description of gear/torque curveFirst gear i = 4.148F B1 WK K3 H2 P2 K1B2K2PT2 H1 PT1 S2 P3P1 S1 S3291_041Gear shifting components: clutch K1 - freewheel F The turbine shaft drives ring gear H1 of the primary planetary gear train. Ring gear H1 drives the planetary gears P1, which rotate around the fixed sun gear S1. Planet carrier PT1 is driven in this way. Clutch K1 connects PT1 to sun gear S3 and thus transmits the torque to the secondary planetary gear train. Freewheel F locks planet carrier PT2. Torque is transferred from sun gear S3 to the short planetary gears P3, and in turn to the long planetary gears P2. The torque, multiplied by planet carrier PT2, is transmitted to ring gear H2, which is connected to the output spur gear. Since first gear is implemented using freewheel F, no power is transmitted during overrun in first gear. In overrun, the gears drive the engine. Freewheel F rotates towards its locking direction (in freewheel direction); the engine brake effect cannot be utilised.Torque curve/power flowReference You will find notes on the schematic diagram on page 28 and in SSP 283 on page 55.Parts are stationary or held in placeParts rotate without contributing to power flow33Gearbox subassembliesFirst gear in tiptronic mode (with engine brake)F B1 WK K3 H2 P2 K1B2K2PT2 H1 PT1 S2 P3P1 S1 S3291_042Gear shifting components: clutch K1 - brake B2 The engine brake effect in first gear can be utilised in special driving situations - e.g. on steep downhill gradients - by selecting first gear in tiptronic mode (B2 closed). The torque curve is as described for first gear (on the previous page). The engine brake effect can only be utilised in the first gear by closing brake B2. As with F, brake B2 locks the planet carrier PT2 in place. Unlike F, however, B2 holds PT2 in place in both directions of rotation. This is necessary for reverse gear and for utilising the engine brake effect in the first gear.34Second gear i = 2.370F B1 WK K3 H2 P2 K1B2K2PT2 H1 PT1 S2 P3P1 S1 S3291_043Gear shifting components: clutch K1 - brake B1 The turbine shaft drives ring gear H1 of the primary planetary gear train. Ring gear H1drives the planetary gears P1, which rotate around the fixed sun gear S1. Planet carrier PT1 is driven in this way. Clutch K1 connects PT1 to sun gear S3 and thus transmits the torque to the secondary planetary gear train. Brake B1 locks the large sun gear S2 in place. Torque is transferred from sun gear S3 to the short planetary gears P3, and in turn to the long planetary gears P2. The long planetary gears P2 orbit around fixed sun gear S2 and drive ring gear H2, which is connected to the output spur gear.35Gearbox subassembliesThird gear i = 1.556F B1 WK K3 H2 P2 K1B2K2PT2 H1 PT1 S2 P3P1 S1 S3291_044Gear shifting components: clutch K1 - clutch K3 The turbine shaft drives ring gear H1 of the primary planetary gear train. Ring gear H1 drives the planetary gears P1, which rotate around the fixed sun gear S1. Planet carrier PT1 is driven in this way. Clutch K1 connects PT1 to sun gear S3 and thus transmits the torque to the secondary planetary gear train. Clutch K3 likewise transmits the torque to the secondary planetary gear train acting on sun gear S2. The secondary planetary gear train is locked in place by the closing of clutches K1 and K3. Torque is now transmitted directly from the primary planetary gear train to the output spur gear.36Fourth gear i = 1.155F B1 WK K3 H2 P2 K1B2K2PT2 H1 PT1 S2 P3P1 S1 S3291_045Gear shifting components: clutch K1 – clutch K2 The turbine shaft drives the ring gear H1 of the primary planetary gear train and the external disc carrier of clutch K2. Ring gear H1 drives the planetary gears P1, which rotate around the fixed sun gear S1. Planet carrier PT1 is driven in this way. Clutch K1 connects PT1 to sun gear S3 and thus transmits the torque to the secondary planetary gear train. The clutch K2 connects the turbine shaft to the planet carrier PT2 and thus transfers the torque to the secondary planetary gear train. The long planetary gears P2, which are in mesh with the short planetary gears P3, together with the planet carrier PT2, drive the ring gear H2, which is connected to the output spur gear.37Gearbox subassembliesFifth gear i = 0.859F B1 WK K3 H2 P2 K1B2K2PT2 H1 PT1 S2 P3P1 S1 S3291_046Gear shifting components: clutch K2 - clutch K3 The turbine shaft drives ring gear H1 of the primary planetary gear train and the external disc carrier of clutch K2. Ring gear H1 drives the planetary gears P1, which rotate around the fixed sun gear S1. Planet carrier PT1 is driven in this way. Clutch K3 connects the PT1 to the sun gear S2 and thus transmits the torque to the secondary planetary gear train. Clutch K2 connects the turbine shaft to the planet carrier of the secondary planetary gear train PT2 and thus transmits the torque to the secondary planetary gear train. The long planetary gears P2, together with the planet carrier PT2 and the sun gear S2, drive the ring gear H2, which is connected to the output spur gear.38Sixth gear i = 0.686F B1 WK K3 H2 P2 K1B2K2PT2 H1 PT1 S2 P3P1 S1 S3291_047Gear shifting components: clutch K2 – brake B1 Brake B1 locks in place sun gear S2. Clutch K2 connects the turbine shaft to the planet carrier of the secondary planetary gear train PT2 and thus transmits the torque to the secondary planetary gear train. The long planetary gears P2 orbit around fixed sun gear S2 and drive ring gear H2, which is connected to the output spur gear. Clutches K1 and K3 are open. The primary planetary gear train does not contribute to power transmission.39Gearbox subassembliesReverse (R) gear i = 3.394F B1 WK K3 H2 P2 K1B2K2PT2 H1 PT1 S2 P3P1 S1 S3291_048Gear shifting components: clutch K3 - brake B2 The turbine shaft drives ring gear H1 of the primary planetary gear train. Ring gear H1 drives the planetary gears P1, which rotate around the fixed sun gear S1. Planet carrier PT1 is driven in this way. Clutch K3 connects the PT1 to the sun gear S2 and thus transmits the torque to the secondary planetary gear train. The brake B2 locks the planet carrier PT2 in place. Torque is transmitted from the sun wheel S2 to the long planetary gears P2. The torque, multiplied by PT2, is transmitted to the ring gear H2, which is connected to the output shaft. At the same time, the ring gear H2 (output) is driven against the direction of rotation of the engine.40Parking lockThe parking lock is a device which prevents the vehicle from rolling when parked. The parking lock is designed in a conventional fashion, i.e. it is operated by the selector lever by means of a Bowden cable (mechanical only). The parking lock gear is a component part of the driven intermediate shaft gearwheel. It also acts as a sender wheel for the gearbox output speed sender G195. The pawl meshes with the parking lock gear and thereby locks the final drive. A constant wheel height is maintained when the axle is raised on one side only. It is therefore not possible to prevent rolling when the front axle is raised on one side (e.g. when changing a wheel using the car jack). In this case, the handbrake must be applied. To reduce the load on the selector lever cable and to allow the selector lever to be operated more easily, the handbrake should be applied on steep gradients before the selector lever is engaged in the "P" position. This eliminates tension between the pawl and the parking lock gear. Before driving away, first shift the selector lever out of "P" and then release the handbrake.PawlParking lock gear Pawl Compression spring Linkage Idler shaftParking lock gear291_104Position "parking lock engaged"291_108Ratchet toothPawlTaperCompression springWhen the ratchet tooth meshes directly with a tooth of the parking lock gear (tooth to tooth), the taper is preloaded by the compression spring. If the parking lock gear turns slightly further, the pawl is forced into the next tooth space.291_108APosition "compression spring preloaded"41Gearbox controlFunction diagram of Audi A3 ´04 (as per March ‘04)F41Shift matrixC3 C1 C10 C7 C9 C5 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C4 C2 C8C1 C7 C9 C5P 1 0 0 1R 1 1 0 0N 0 1 0 1D 0 1 1 0S 1 1 1 1Switch for P/N signalF125R signal/information for self-diagnosis21 36 10 22 47 49 01P/N signal to onboard power supply control unit J519 for control of terminal 5002Gearbox 09GG194 N89 N92 N282 N90 N283 N91 N93 G93 G182 G195P PN88+-+-+-+-+-+-+-++ + -+ A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 B1 B2B3 B4 B5 B6 B7 B8G193J21725 24 50 38 39 51 08 45 17 31 43 05 44 04 18 30 32 16 06 42 15 4142F41 F125 F189 F319 G93 G182 G193 G194 G195KL.30a KL.15aReversing switch Multi-function switch Tiptronic switch Selector lever locked in position P switch Gearbox oil temperature sensor Gearbox input speed sender Automatic gearbox hydraulic pressure sender -1Automatic gearbox hydraulic pressure sender -2Gearbox output speed sender Automatic gearbox control unit Solenoid valve 1 Solenoid valve 2 Solenoid valve 3 Solenoid valve 4 Solenoid valve 5 Solenoid valve 6 Selector lever lock solenoid Solenoid valve 9 Solenoid valve 10J217 N88 N89 N90 N91 N92 N93 N110 N282 N28303 27 28F319Gear selector mechanismSelector lever sensors with F189PRNDS + N110+ -D1D2 D3 D4 D5 D6 D7 D8 D9 D10Output Input Gold-plated contact Twisted wireKL.30a KL.15a48 29 11 37 KL.31 KL.58d P KL.31P signal to J527 for ignition key withdrawal lock releaseTiptronic signal (FMR signal)Diagnosis CAN bus14 13Note Hydraulic pressure senders G193 and G194 are not installed in gearboxes with build dates from week 27/2004 on.Diagnosis connectionK line09 46 34 52Driveline CAN bus high Driveline CAN bus lowNote The current version of the current flow diagram must be used for fault-finding on vehicle.291_04943Gearbox controlFunction diagram of Audi TT (as per March ‘04)F41Shift matrixC3 C1 C10 C7 C9 C5 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C4 C2 C8C1 C7 C9 C5P 1 0 0 1R 1 1 0 0N 0 1 0 1D 0 1 1 0S 1 1 1 1P/N signal, control of terminal 50Switch for P/N signalF125to the reversing lights R signal/information for self-diagnosis21 36 10 22 47 49 01 0209G gearboxG194 N89 N92 N282 N90 N283 N91 N93 G93 G182 G195P PN88+-+-+-+-+-+-+-++ + B2 B3 B4 B5 B6 B7 B8 + -G193J217A1A2A3A4A5A6A7A8A9 A10A11 A12 A13 A14B125 24 50 38 39 51 08 45 17 31 43 05 44 04 18 30 32 16 06 42 15 4144F41 F125 F189KL.30aReversing switch Multi-function switch Tiptronic switch Gearbox oil temperature sensor Gearbox input speed sender Automatic gearbox hydraulic pressure sender -1Automatic gearbox hydraulic pressure sender -2Gearbox output speed sender Starter inhibitor relay Automatic gearbox control unit Control unit with display in dash panel insert Solenoid valve 1 Solenoid valve 2 Solenoid valve 3 Solenoid valve 4 Solenoid valve 5 Solenoid valve 6 Selector lever lock solenoid Solenoid valve 9 Solenoid valve 10J207G93 G182 G193 G194 G19530 85 2 686 87A 87 4 5 8ZAS = ignition switch ZE = central electricsJ207 J217 J285from ZAS to starterKL.50 KL.50 KL.15a KL.30a KL.15a03 27 28Gear selectorN110PRNDS + -N88 N89 N90 N91 N92 N93 N110 N282 N283Selector lever sensors with F1891 2 1 2 3 4 5 6 7 8Output Input29 48 11 37 KL.15a KL.58dGold-plated contact Twisted wireDiagnosis CAN bus Diagnosis connectionNoteK line09 14 13 46 34 52Tip - from the tiptronic steering wheel Tip + from the tiptronic steering wheel Driveline CAN bus high Driveline CAN bus low v signal to J285Hydraulic pressure senders G193 and G194 are not installed in gearboxes with build dates from week 27/2004 on.Note The current version of the current flow diagram must be used for fault-finding on vehicle.291_05045Gearbox controlAutomatic gearbox control unit J217The control unit is located in the wheel housing at the front left on the Audi A3 ‘04 or in the plenum chamber on the Audi TT. It is connected by a 52-pin plug. VAS adapter cable 1598/48 is available for static and dynamic measurements on the system.Installation location on Audi A3 ‘04The control unit is made by ASIN AW Japan. Update programming is possible with the VAS 5051.291_051Installation location on Audi TTAutomatic gearbox control unit J217291_111291_053pin assignments of the interfaces (see table on page 47)291_054 46pin assignments on control unit J217. Connector A/B/C/D to gearbox or peripheral devicespin 1 2 3 4 5 6 7 8 9 10 11 12 13pinDesignation Ground terminal 31 Ground terminal 31 Voltage supply terminal 30pin 27 28 29 30 31 32 33 34 35 36 37 38 39pinDesignation Voltage supply terminal 15 Voltage supply terminal 15D7*/ 1** A7 A13 A6Selector lever lock solenoid N110 (+) Solenoid valve N90 (+) Solenoid valve N93 (+) Solenoid valve N282 (–) unassigned CAN-low unassignedA9 A11 A4Solenoid valve N283 (+) Solenoid valve N91 (+) Solenoid valve N92 (–) unassignedB2Gearbox oil temperature sensor G93 (-/signal) K lineC7 4**Multi-function switch F125 unassigned*, Tip + on Audi TT** unassigned unassigned*, steering wheel Tip + on Audi TT**C9 5** B5 B4Multi-function switch F125 unassigned*, Tip - on Audi TT** Gearbox output speed sender G195 (+) Gearbox input speed sender G182 (-/signal) unassigned14 15 16 17 18 19 20 21 22 C8 C5 A2 A5 A14 A8unassigned*, steering wheel Tip - on Audi TT** Solenoid valve N89 (+) Solenoid valve N282 (+) Solenoid valve N93 (–) Solenoid valve N90 (–) unassigned unassigned Reverse (R) gear signal/feedback for self-diagnosis Multi-function switch F12540 41 42 43 44 45 46 47 48 C1 D6*/ 3** A1 A3 A12 A10 B1Solenoid valve N88 (+) Solenoid valve N92 (+) Solenoid valve N91 (–) Solenoid valve N283 (–) Gearbox oil temperature sensor G93 (+) CAN-high Multi-function switch F125 Tiptronic information (FMR signal)*/ Tiptronic gate** unassigned23 24 B7unassigned Hydraulic pressure sender 1 G19349 50 B6Gearbox output speed sender G195 (–/signal) Gearbox input speed sender G182 (+) unassigned*, v signal on Audi TT**25 26B8Hydraulic pressure sender 2 G194 unassigned51 52B3Note Hydraulic pressure senders G193 and G194 are not installed in gearboxes with build dates from week 27/2004 on.* **in the Audi A3 ‘04 in the Audi TTpin on control unit J217 pin on connector A/B/C/D47Gearbox controlSensorsMulti-function switch F125Connector C (on wiring harness)2 14 38 5 710 9291_057Sliding contact switch291_120291_055Contact lever adjusting nutNote The contact lever adjusting nut must not be slackened!Switch for positions "P" and "N"Reversing switch F41C6C3C1C7C9C5C2C8C10C4291_056Reference The multi-function switch must be set after installation or if the wrong gear is indicated on the dash panel insert (refer to Workshop Manual).The multi-function switch is a mechanical multiposition switch with 6 sliding contacts: – 4 selector valve position switches – 1 reversing switch F41 – 1 switch for positions "P" and "N" for starting control48Shift logic F125P/N signalR signalPosition signalData block 9/4. ValueC2 P R N D SC4C10C8C3C1C7C9C5Switch positionIntermediate position1001 1101 1100 1101 0101 0111 0110 0111 1111291_058The task of the multi-function switch F125 is to transfer selector lever positions to the gearbox control unit J217. The information on selector lever position is required to realise the following functions: – Starter inhibitor control (see function diagram) – Reversing lights control (see function diagram) – P/N lock control (activation of solenoid N110) – Sport program recognition – Transfer of selector lever position (P/R/N/D/S) by CAN BUS network as information for other control units49Gearbox controlTiptronic switch F189, Audi A3 ‘04The tiptronic switch F189 consists of 3 Hall sensors and is integrated in the selector lever sensors (see page 9). Switch F189 is operated by 2 permanent magnets. The signals from F189 are evaluated by the selector lever sensors and sent through a separate interface to the gearbox control unit J217 in the form of a frequency-modulated square-wave signal. The FM square-wave signal consists of a high pulse with a fixed time of approx. 3 ms and a low pulse time assigned to each selector lever position. A distinction is made only between selector lever in automatic gate (P, R, N, D, S), selector lever in tiptronic gate, selector lever in Tip + and selector lever in Tip - (see DSO images). The interface pin 48 to the selector lever sensors is monitored continuously by the self-diagnosis system. The system can diagnose and differentiate between open circuit, short circuit to positive and short circuit to ground.Note Intermediate positions of the selector lever or faults can produce deviating signal patterns. Faults are saved to the fault memory.DSO image - signal from F189. Selector lever in P, R, N, D or SMesstechnik DSO 5 V/Div.=Auto-Betrieb 5 ms/Div.Standbild Amplitudendifferenz A5.500 V 3 msZeitdifferenz39,5 msCursor 10Cursor 2CursorMultimeterFahrzeug EigendiagnoseDruckenHilfe291_096DSO connection: – black probe tip pin 1(J217) – red probe tip pin 48 (J217) Test conditions: ignition "on"Auxiliaries: – VAS 5051 – V.A.G 1598/48 with – V.A.G 1598/4250DSO images - signal from F189Selector lever in P, R, N, D or SSelector lever in tiptronic gate291_096Selector lever in Tip -291_097Selector lever in Tip +291_098291_099The selector lever sensors diagnose the tiptronic switch F189 continuously, even when the selector lever is not in the tiptronic gate or being operated. This additional safety was made necessary by the elimination of selector lever positions 4, 3 and 2. With the D/S selector lever gate, the tiptronic function must be used to prevent upshifting (move the shift selector lever into the tiptronic gate).For reasons of reliability, a malfunction of the F189 will be diagnosed even if the tiptronic has not previously been operated.51Gearbox controlTiptronic switch F189, Audi TTThe tiptronic switch F189 is integrated in the selector lever gate pcb. It consists of three Hall sensors which are operated by permanent magnets on the masking panel. The F189 generates a square-wave signal with a fixed frequency at the outputs (pins 3, 4 and 5) of the shift gate. Depending on the "switch position" (tiptronic gate, Tip + and Tip -), the signal will be modified or the voltage level will be set to plus or minus. Solenoid 2 is used for continuous diagnosis of the F189 in selector lever positions "D" and "S". This additional safety was made necessary by the elimination of selector lever positions 5, 4, 3 and 2. With the new selector lever gate, the tiptronic function must be used to prevent upshifting (shift selector lever into tiptronic gate), e.g. to utilise the engine brake effect when driving downhill). For reasons of reliability, a malfunction of the F189 will be diagnosed even if the tiptronic has not previously been operated.Hall sensors for selector lever positions "P", "R", "N", "D" and "S"Tiptronic switch F189 (3 Hall sensors)LED LEDSolenoid 1 291_100A291_100B 291_100 Solenoid 252Function diagramGear selector mechanismPRNDS + -Selector lever sensors with tiptronic switch F189N110F189 J217Tiptronic switch Automatic gearbox control unit Selector lever lock solenoid12 1 2 3 4 5 6 7 8N110J21729 48 11 37KL.58dOutputKL.15a14 13Input291_103DSO image - signal from F189 (Audi TT)Voltage level Ubatt in selector lever positions "P", "R" and "N"Signal characteristic in selector lever positions "D" and "S"Messtechnik DSO 2 V/Div.= vAuto-Betrieb 10 ms/Div. sStandbildKanal AKanal BTrigger-ModeMess-ModeT 0Voltage level (ground) in selector lever positions Tip + (pin 11) and Tip - (pin 37) or in the tiptronic gate (pin 48)PositionZeit/Div.MultimeterFahrzeug EigendiagnoseDruckenHilfe291_020DSO connection: – black probe tip pin 1 (J217) – red probe tip pin 11, 37 or 48 (J217) Test conditions: "ignition "on" (engine not running)Auxiliaries: – VAS 5051 – V.A.G 1598/48 with – V.A.G 1598/4253Gearbox controlGearbox input speed sender G182The G182 determines the gearbox input speed (turbine speed) at the external disc carrier of clutch K2. The electronic gearbox control requires the exact turbine speed to realise the following functions: – Control, adaption and monitoring of gear shift operations and gear selection – Control and monitoring of the torque converter lock-up clutch – Diagnosis of the shifting components and plausibilisation of engine speed and gearbox output speed Note Due to torque converter slip, the gearbox input speed (turbine speed) is not equivalent to the engine speed (except when the torque converter lock-up clutch is fully closed).Gearbox input speed sender G182External disc carrier K2 (sender wheel for G182)291_119 Gearbox input speed sender G182 Bottom view of gearbox291_061Protective and substitute function in case of failure: – The engine speed is used as a substitute value – No adaption of gear shift operations – No controlled operation of the torque converter lock-up clutch (open or closed only) – No pressure control when selecting gears (e.g. N-D or N-R), harsh engagement54Function - sender G182 Sender G182 is based on the Hall principle. The output signal is a square-wave signal whose frequency is proportional to turbine speed.Voltage supply Ground and signalG182B3 B451 39G195B5 B638J21750291_064DSO image - signal from G182Messtechnik DSO 0,5 V/Div.= DAuto-Betrieb 5 ms/Div. /StandbildKanal AKanal BTTrigger-ModeMess-Mode0PositionZeit/Div.MultimeterFahrzeug EigendiagnoseDruckenHilfe291_065 Voltage level when turbine shaft is stationary (gear selected/road speed 0 kph)DSO connection for G182 – black probe tip pin 1 – red probe tip pin 39 Test conditions: – Engine idling – Selector lever in position N or P Auxiliaries: – VAS 5051 – V.A.G 1598/48 with – V.A.G 1598/4255Gearbox controlGearbox output speed sender G195The G195 determines the gearbox output speed (gearbox output speed) at the parking lock gear. The parking lock gear is a component part of the driven intermediate shaft gearwheel. On account of the ratio between planetary gear output and intermediate shaft, both speeds are proportional to each other. The control unit computes the actual gearbox output speed based on the programmed reduction ratio. One of the most important signals generated by the electronic gearbox control is the gearbox output speed. There is a defined relationship between gearbox output speed and vehicle road speed. The gearbox output speed is required to realise the following functions: – Shift point selection – Functions of the Dynamic Shift Program DSP (e.g. driving condition evaluation) – Diagnosis of shifting components and plausibilisation of engine and turbine speed (gear monitoring)Gearbox output speed sender G195291_118 Bottom view of gearbox Gearbox output speed sender G195Parking lock gear (sender wheel for G182)Idler shaft291_063Protective and substitute function in case of failure: – The wheel speeds from the ESP control unit are used as a substitute value (transmitted by CAN-BUS) – Limited DSP capabilityNote Pay attention to correct assignment of parts and coding due to the dependence of road speed (v signal) on final drive ratio.56Function - sender G195 Sender G195 is based on the Hall principle. The output signal is a square-wave signal whose frequency is proportional to gearbox output speed (road speed).Voltage supply Ground and signalG182B3 B451 39G195B5 B638J21750DSO image - signal from G195291_064Messtechnik DSO 0,5 V/Div.= DAuto-Betrieb 5 ms/Div. /StandbildKanal AKanal BTTrigger-ModeMess-Mode0PositionZeit/Div.MultimeterFahrzeug EigendiagnoseDruckenHilfe291_065 Voltage level at a road speed of 0 kphDSO connection for G195 – black probe tip pin 1 – red probe tip pin 50 Test conditions: – Road speed 10 kph – Selector lever in position D, engine idling (vehicle raised on auto-hoist) Auxiliaries: – VAS 5051 – V.A.G 1598/48 with – V.A.G 1598/4257Gearbox controlHydraulic pressure senders G193 and G194Automatic gearbox hydraulic pressure sender -2G194 (brake B2)Bottom view of valve body on gearboxN91 N93 N89 N89Automatic gearbox hydraulic pressure sender -1G193 (clutch K1)N88 N92N282291_067N283N90 A2291_039AG193 and G194 are diaphragm pressure switches and connect to ground when pressure exceeds approx. 3 bar. Both switches are identical. The switching signals are used to monitor the electrohydraulic control.They provide the control unit J217 with feedback on the circuit state or electrohydraulic activation of shifting components K1 and B2. As a result, malfunctions of the electrohydraulic control can be diagnosed more accurately and the appropriate safety precautions taken.Protective and substitute function in case of failure: Note – If the malfunction occurs, then the emergency running mode is activated and/or engine torque is reduced depending on the situation. Hydraulic pressure senders G193 and G194 are not installed in gearboxes with build dates from week 27/2004 on.58The G193 responds to the hydraulic activation of clutch K1. G194 responds to the electrohydraulic activation of brake B2. Therefore, G194 shifts to tiptronic mode only - first gear.Since reverse gear is only engaged by the gear selector valve (mechanical and hydraulic), G194 is not closed in reverse (R) gear (see shift logic on page 32 and description of gear on page 40).Switch "closed" ATF pressure approx. 3 barSwitch "open" ATF pressure approx. 3 bar+DiaphragmGround 291_068 291_069G194G93G182G195P P+-+-+ B1 B2B3 B4 B5 B6 B7 B8G193“Diaphragm ATF pressure“Legend G193 G194 Automatic gearbox hydraulic pressure sender -1Automatic gearbox hydraulic pressure sender -2Automatic gearbox control unitJ217J21725 24 50 38 39 51 08 45Output Input291_10659Gearbox controlGearbox oil temperature sensor G93Gearbox oil temperature sensor G93N91 N93 N89 N89O-ring291_066N88 N92N282N283Sensor G93 is located in the valve body and is mounted by means of a retaining plate. It is an NTC resistor and is a component part of the wiring harness. (NTC - Negative Temperature Coefficient)N90 A2291_039BThe ATF temperature is required to realise the following functions: – Adaptation of shift pressures (system pressure) as well as pressure increase and pressure reduction during gearshifts. – Activation and deactivation of temperaturedependent functions (warm-up program, torque converter lock-up clutch, etc.). – Activation of gearbox protection measures if the ATF temperature is too high (Hotmode). – Adaptation of shift pressures (EDL pilot current)As protection against overheating, countermeasures (Hotmode) are initiated if defined temperature threshold values are exceeded: Hotmode 1. Stage (approx. 127 °C): The DSP function is used to bias the shift characteristics towards higher engine speeds. The operating range in which the torque converter lock-up clutch is closed is extended. Hotmode 2. Stage (approx. 150 °C): Engine torque is reduced.60Wiring harness with G93G93 NTC resistor characteristic of the G93105104Resistance in Ω103Wiring harness - sensors in gearbox102101 -40291_077040 80 Temperature in °C120160291_123Connectors - B/pin 1 and 2 for G93 with gold-plated contactsProtective and substitute function in case of failure: – A substitute value is generated from the engine temperature and the operating time. – No controlled operation of the torque converter lock-up clutch (open or closed only)291_078– No adaptation of shift pressures (which generally results in more harsh engagement)61Gearbox controlInterfaces/auxiliary signalsKick-down informationThere is no separate switch for kick-down information. A "force element" is integrated in the accelerator position sender in place of the stop buffer (for manual gearboxes). The force element produces a "mechanical pressure point" which conveys an authentic "kickdown feel" to the driver. When the driver operates the kickdown, the full-load voltage of the accelerator position senders G79 and G185 is exceeded. If a voltage defined in the engine control unit is attained in the process, this is interpreted as a kickdown and transferred to the automatic gear box (via driveline CAN bus). The kick-down point can only be checked using the diagnostic tester.Accelerator pedal of Audi A3 ´04Reference For a description of the function of the accelerator pedal module in the Audi A3 ‘04, refer to SSP 290 (from page 27).Accelerator position sender G79/G185Kick-down "force element" 291_071Note Accelerator pedal of the Audi TT If the accelerator pedal module or the engine control unit in the Audi TT is replaced, the kick-down point must be readapted.Kick-down "force element" Kick-down range Accelerator pedal travel5,0 G79Accelerator position sender G79/G185Signal voltage in VG1850291_07320 %40 %60 %80 %100 %291_074IdlingDriver torque input Full throttle stop mechanical Accelerator pedal limit stop62Road speed signal - Audi TT (v signal)To allow use of the 09G gearbox in the Audi TT, the J217 generates a road speed signal for the dash panel insert. The v signal is a square-wave signal which replaces a separate speedometer sender, as found on some vehicles with manual transmission. The v signal is required only for the Audi TT, since, unlike the Audi A3 ‘04, the dash panel insert does not process road speed signals via CAN-Bus.DSO image - v signalMesstechnik