TECHNICAL DOCUMENTATION

SSP 182 Audi A3 – The Engineering

PDFEN74 pages5 MB
SSP 182 Audi A3 – The Engineering - PDF cover

This PDF is currently unavailable.

Read document text
Service.182Audi A3 - The EngineeringSelf Study ProgrammeFor internal use only. © VOLKSWAGEN AG K-VK-12, Wolfsburg All rights reserved. Subject to technical changes. 640.2810.01 20 Technical Status: 07/96 Y This paper was made using chlorine-free bleach.Service Department The EngineeringSSP 181/92 Audi A3 New models / New engineering............................ Body Programmed crumple zones................................. Safety Soft cushions and stable seats.............................. Test Your Knowledge Subject: body and safety ...................................... Engines From engine lubrication to functional diagram... Test Your Knowledge Subject: engines .................................................... Gearbox Tooth for tooth........................................................ Running Gear Well-clamped and adjustment-free...................... Steering Locking teeth and crash-tested............................. Braking system Power under pressure........................................... Test Your Knowledge Subject: running gear, steering and brakes......... Electrical system Switches and controls........................................... Answers What you managed to remember.........................4 6 10 14 16 50 52 54 58 62 63 64 66The Self Study Programme is not a Workshop Manual! Please refer to the relevant Service Literature for all inspection, adjustment and repair instructions.NewImportant/Note3 Audi A3New models New engineeringSafety • Side padding • Seats with high transverse rigidity • Easy Entry • Seat occupied recognition (SOR) Body • Side members • Concertina principle • Side reinforcement in doors • Flush fitting between B pillar and sill Footwell cross member Engines / Gearbox • Engine lubrication • Engine cooling • Engine electrics • System overviews • Self-diagnosis • Functional diagrams • Reversing brakeIn this SSP we will explain the technical details of the Audi A3 to you.SSP 182/81SSP 182/82SSP 182/834 Running gear • Cast wheel bearing housing with singlebolt clamp • Caster • Self-aligning double ball bearing • Oblique rear axle mountingSteering • Locking teeth and clamp • Lock • Crash conceptBrake • Disc brakes at front and rear • Dacrometised boltsAbove all, new, special construction and operation features.SSP 182/84SSP 182/85SSP 182/865 BodySafety is ... programmed crumple zonesIn other words: When the car is designed, every effort is made to minimise deceleration forces acting on the occupants. To achieve this aim, the body must be deformable, because this enables it to absorb energy.Side memberFootwell cross memberSide memberSSP 182/7To ensure the occupant cell remains intact during a collision, the entire front section of the car is designed to deform in a predefined manner.6 The specific deformation behaviour of the car’s front section is mainly determined by the body side members.Full extension side membersSide memberThe front side members each consist of three mash seam welded panels with thicknesses of 2 mm, 3 mm and 1.5 mm. The different material thicknesses are calculated depending on the strength they require and their location.Subsection 1 Subsection 2 Subsection 3SSP 182/8Crumpling principle of the side members The side members fold up when compressed and therefore absorb a maximum of impact energy. We refer to this as the concentina principle.Subsection of side memberCover plateSide memberSSP 182/107 BodyDuring a side impact, the only solution is to distribute the impact force over the entire structure and reduce the impact force by means of additional energy absorbing elements.High-strength side reinforcements in the doors The side reinforcements consists of highstrength extruded aluminium sections. They are shaped in double rectangular sections made of aluminium and have a high energy absorption capacity. During a side impact, the force exerted on the car is distributed to the A pillar, B pillar and sill by the side reinforcements.Side reinforcementSSP 182/11Positive interlocking of door and pillars and in sill area During a side impact, the outer structure of the door crumples first. The A and B pillars as well as the strong sill beneath the door absorb additional forces. At the same time, they channel forces into the sturdy floorpan assembly.DoorSillSSP 182/128 Connection between B pillar and reinforcement in sill The connection between the B pillar and the reinforcement in the sill up to pillar A covers a large area. The reinforcement is formed in one piece and extends all the way along the structure. This bond plays an important part in force distribution.B-pillarsillSSP 182/103Integrated footwell cross member During a collision, the integrated footwell cross member keeps the footwell intact and provides a rigid survival space for the occupants.Footwell - cross memberSSP 182/99 SafetySoft cushionsDuring a side impact, body deformations follow a very limited, direct path. Only the overall depth of the door is available as a buffer.Pelvis and rib paddingsThe side paddings in the doors and side sections are made of rigid foam. They are also energy absorbent, i.e. they soak up energy and thus dampen the side impact. The car occupants are protected in the pelvis and rib areas.Side padding, frontSSP 182/87Side padding, rearSSP 182/88SSP 182/8910 Sturdy seatsThe Easy Entry system, optimal seating comfort and the highest standard in safety engineering make an excellent combination.SSP 182/80The Easy Entry system When the back of the front seat is pushed forwards, the entire seat slides forwards. This makes the space behind the front seat larger and a passenger can enter the rear of the cabin more easily.Seats with high transverse rigidity A frame structure with high transverse rigidity is the result of: one circumferential square tube, one transversely mounted U-section, one sturdy support tube between the seat rail and seat frame.Support tube Rear section Circumferential square tubeDuring a side impact As a result of the high transverse rigidity, the seats play a greater role in force distribution.SSP 182/7911 SafetyTrying to fold a triggered airbag back into its original shape would be quite an experience. It can be compared to trying to re-pack gifts which won’t fit into their original box. Therefore, we prefer not to trigger an airbag if it is not needed. This requires a link between the airbag triggering function and the seat.Seat occupied recognition Seat unoccupied When the ignition is switched on, the SOR always assumes that the seat is occupied. The change in state is recognised after 20s : “Seat unoccupied“. SSP 182/95Seat occupied When the ignition is switched on, the change in state is recognised as soon as the seat is occupied: “Seat occupied“.SSP 182/96Seat occupancy is recognised by a pressure sensor in the front passenger seat.ExcerptPressure sensorSSP 182/76 SSP 182/9012 The pressure sensor comprises two superimposed films.SSP 182/105One of the films consists of an electrically conductive polymer.The electrically conductive polymer connects the positive contact to the negative contact.This diagram illustrates only:one negative electrodSSP 182/107and one positive electrodeThe other film contains an interrupted electrical circuit with several positive and negative electrodes in the shape of fingers.Negative electrodeSSP 182/97The electrical circuit is closed. If no pressure is applied to the electrically conductive film, the resistance between the positive and negative contacts is high. The resistance decreases the more the electrically conductive film is pressed against the positive and negative electrodes.Positive electrodeSSP 182/106Using the information provided by the pressure sensor, the control unit assumes the following: • high resistance “seat unoccupied“ • low resistance “seat occupied” The airbag is activated in the event of a collision.Airbag control unitAirbagSSP 182/9913 Test Your KnowledgeNow you can answer the following questions. You will see what you have remembered.1. Identify the subsections from which a side member is made. Specify the material thickness in millimetres.SSP 182/1042. Which components define the specific deformation of the car’s front section?3. Please complete.The side reinforcements are made of......................... ................................................................................. They are capable of absorbing ................................................ .4. Side paddings protect the car’s occupants in the ... Please complete the above sentence by stating which parts of the body are protected.14 5. Please mark with cross where applicable.The support structure with high transverse rigidity for the seat comprises:A One circumferential square tube B One longitudinal rear section C One sturdy support tube6. The pressure sensor consists of two superimposed films. Please complete the following text and drawing. One of the films consists of ........................... ........................................................................The other film contains............ ........................................................................SSP 182/1147. Please complete and underline where appropriate.If the seat is occupied,............. .... is exerted on ...................................................................... The resistance is high / low.Now you can answer all the questions. If not, please read the relevant section again.15 Engine LubricationWell lubricatedOn the following pages you will learn about the new features of the oil circuit. • The oil pressure control valve is installed downstream of the oil filter. Therefore, there is only one oil pressure switch. The oil return cut-off valve is integrated into the filter connection.•Gear intermeshing zoneThe oil pump is an internal gear pump. The advantages of this are: • • • The gear intermeshing zone is smaller, resulting in less friction The operating area is large, resulting in high suction capacity The number of moving parts is kept to a minimumSSP 182/26The oil pump is driven by the crankshaft by means of a chain. The chain is tensioned by means of a spring-loaded sliding block, i.e. the chain tensioner.Chain tensioner Driving chainSSP 182/2816 Oil circuitThe oil ducts illustrated by broken lines in the overview only exist in the 1.9-ltr. TDI engine.CamshaftVacuum pumpHydraulic bucket-type tappets Exhaust gas turbochargerPiston cooling sprayOil pressure control valve Oil pressure switch Short-circuit valve Pressure relief valve Oil pump Oil return cut-off valveOil filterOil coolerSSP 182/2717 Engine coolingWell-cooledThe engine cooling system also has new features.The coolant pump is installed in the cylinder block. It is driven by the rib belt. The pump gear is made of plastic. The advantages of this are:• •Fewer components Less weightSSP 182/31The coolant thermostat is integrated in the cylinder block. This eliminates the need for a housing and saves weight.SSP 182/3218 Coolant circuitHeat exchanger (heater)Throttle valve control unitPressure equalisation tankCoolant pumpHeat exchanger (automatic gearbox oil )Oil coolerThermostat CoolerSSP 182/3019 1.6-ltr. Engine AEHSpecial features of the 1.6-ltr. engine Twin-path intake manifoldThe 1.6-ltr. engine has a twin-path intake manifold. This enables the intake path length to be adapted to engine requirements. The change-over flaps are vacuum-operated. A vacuum box located beneath the intake manifold ensures that the change-over flap can operate when there is insufficient vacuum.Change-over flapReflection point of pressure fluctuationsPosition of the change-over flap at engine speeds of up to 4000 rpm Long intake path = torque positionThe downward movement of the piston produces pressure fluctuations in the intake air. These pressure fluctuations are reflected at the rear of the intake manifold. The length of the intake manifold is designed so that the reflected pressure fluctuations ensure the cylinder is filled with the correct amount of air-fuel mixture.SSP 182/41Reflection point of pressure fluctuationsChange-over flapPosition of change-over flap at engine speeds of greater than 4000 rpm Short intake path = performance positionAt high speeds less time is available to fill the cylinders. The intake path must therefore be short. The change-over flaps open the short intake path. The pressure fluctuations are reflected at the front of the intake manifold. This also ensures the cylinder is filled correctly at high speeds.SSP 182/4220 The change-over flaps are controlled by the engine control unit via the twin-path intake manifold change-over valve and the vacuum box.Change-over flaps closedChange-over flaps openTwin-path intake manifold change-over valve N156Twin-path intake manifold change-over valve N156Vacuum box Atmosphere Vacuum Atmosphere VacuumVacuum boxVacuum box for twin-path intake manifold changeoverVacuum box for twin-path intake manifold changeoverSSP 182/98SSP 182/11321 1.6-ltr. Engine AEHSystem overview, Simos 2 SensorsAir mass meter G70Engine speed sender G28Hall sender G40Lambda probe G39Throttle valve control unit J338with Throttle valve potentiometer G69 Throttle valve positioner potentiometer G88 Idling speed switch F60Intake air temperature sender G42Coolant temperature sender G62Knock sensor G61Additional signals:Road speed signal Terminal 50 Air conditioner - ready Signal for engine intervention22 Fuel pump relay J17ActuatorsFuel pump G6Simos 2 control unit J361Injectors N30-N33Output stage N122 and ignition coils N/N128Activated charcoal filter solenoid valve 80Lambda probe heater Z19Wiring for diagnosis and immobiliserThrottle valve control unit J338with throttle valve positioner V60Intake manifold change-over valve N156Additional signals:Throttle valve potentiometer signal Engine speed signal Air conditioner - switch-off Fuel consumption signalSSP 182/3623 1.6-ltr. Engine AEHHall sender G40180° sender wheelLocated behind the camshaft sprocket. The 180° sender wheel is integrated in the camshaft sprocket.Hall sender G40SSP 182/37Signal utilisationThe signal is required to detect when the 1st cylinder is at TDC. The engine control unit defines the injection sequence accordingly. The signal is also required to control knocking in the individual cylinders.Effects of signal failureIf the Hall sender fails, the knock control is switched off by the engine control unit and the ignition timing is lagged because the knock effects cannot be assigned to the cylinders. Nevertheless, the engine continues to run.Self-diagnosis “Fault message“ Hall sender G40 “no signal“Hall sender G40 “implausible signal“24 Self-diagnosis “Read measured value block“You can check to see if the valve timing of the engine is set correctly using the address word “Read measured value block“.The falling edge of the Hall sender signal must coincide with the signal of the 88th tooth of the crankshaft sprocket (tolerance range ±2 teeth). The teeth of 2 revolutions of the crankshaft are then added.The rising edge of the Hall sender signal must coincide with the 28th tooth of the crankshaft sprocket (tolerance range ±2 teeth). If the values coincide, you can assume that the engine valve timing is correct.58 618811812858 61Crankshaft signal Tooth gap 119 + 120Valve timing signal Falling edge Rising edgeSSP 182/102Electrical circuitJ361 62 76 6762 67 76Positive Sensor earth Hall sender signal+°G40-SSP 182/11725 1.6-ltr. Engine AEHSelf-diagnosisFaults can be evaluated using fault reader V.A.G 1551 or 1552.V.A.G - EIGENDIAGNOSE 01 - Motorelektronik HELP1 2 3 4 5 6 7 8 9 C 0 QHELPPRINTV.A.G 1551SSP 182/39The following functions can be checked in the self-diagnosis using the address word: ((V.A.G SELF-DIAGNOSIS 01 - Motor electronics))V.A.G - EIGENDIAGNOSE 01 - Motorelektronik HELP01 - Interrogate control unit version 02 - Interrogate fault memory 03 - Final control diagnosis 04 - Initiate basic setting 05 - Erase fault memory 06 - End of output 07 - Encode control unit 08 - Read measured value blockYou can find explanatory notes on self-diagnosis and address words in the Workshop Manual.26 The colour-coded components are checked during self-diagnosis.SSP 182/7727 1.6-ltr. Engine AEHFunctional diagram, Simos 230 15J17SSSλZ19 G39 G70 N80 N156N30N31N32N3347380586527 25 26121315646659 6974627576566367M V60 F60 J338 G88 G69+°G40G28MG6inout3128 30 15SSABCDEFGHJ6 J3611819202281023731685453271 78ABN122 N G61 G42 G62 N128SSP 182/40P Q31SSP 182/40 Components:Additional signals:F60 G6 G28 G39 G40 G42 G61 G62 G69 G70 G88 J17 J338 J361 N N30 N31 N32 N33 N80 N122 N128 N156Idling speed switch Fuel pump Engine speed sender Lambda probe Hall sender Intake air temperature sender Knock sensor Coolant temperature sender Throttle valve potentiometer Air mass meter Throttle valve positioner potentiometer Fuel pump relay Throttle valve control unit SIMOS 2 control unit Ignition coil Injector, cylinder 1 Injector, cylinder 2 Injector, cylinder 3 Injector, cylinder 4 Activated charcoal filter system solenoid valve 1 Output stage Coil 2 Intake manifold change-over valveA B C D E F G H JEngine speed signal Fuel consumption signal Wiring for diagnosis and immobiliser Road speed sensor Terminal 50 Air conditioner- switch-off Air conditioner - ready Signal for engine intervention Throttle valve potentiometer signalP Q V60 Z19Spark plug connector Colour code: Spark plug Throttle valve positioner Lambda probe heater Input signal Output signal Positive Earth29 Dummy page 1.8-ltr. 5V Engine AGN1.8-ltr. 5V engine ... Variable valve timingThe different gas flow characteristics which take place in the engine combustion chamber have a major bearing on perfomance, torque and exhaust emissions. Variable valve timing adapts valve timing to the demands of the engine. Its task is to adjust the valve opening and closing times as a function of speed. This improves torque in the lower to medium speed range and performance in the upper speed range. Variable valve timing also reduces pollutant emissions.Inlet camshaft Exhaust camshaftSSP 182/44This is how it works:Only the inlet camshaft is adjusted. The exhaust camshaft is driven by the crankshaft by means of the rib belt. The inlet camshaft is driven by the exhaust camshaft by means of a chain. The inlet camshaft is adjusted by an electrically controlled hydraulic cylinder which simultaneously acts as a chain tensioner.When valve timing is adjusted, the inlet camshaft is adjusted towards “advance“. Variable valve timing is controlled by the engine control unit.30 Performance positionIn the performance position, the change point of the timing chain is in advance of the inlet camshaft. This is the basic position. No timing adjustment takes place.Change point of timing chain Inlet camshaftExhaust camshaftSSP 182/127Torque positionTo adjust valve timing, the chain tensioner is pressed downwards under oil pressure. This changes the change point of the timing chain. It is now after the inlet camshaft. The camshaft is adjusted towards “advance“.inlet camshaftExhaust camshaft Change point of timing chainSSP 182/12631 1.8-ltr. 5V Engine AGNBasic positionThe variable valve timing mechanism is supplied with oil through a drilling in the cylinder head. Depending on the position of the adjusting piston, oil pressure is applied to control pipe A or B.Oil supply Chain tensioner Control pipe BOil return pipeHydraulic cylinder with adjusting pistonControl pipe ASSP 182/45Performance positionIn the de-energised state, control pipe A is open and oil pressure forces the chain tensioner into the performance position (basic position).32 Torque positionOil supply Chain tensioner Control pipe BOil return lineHydraulic cylinder with adjusting pistonControl pipe ASSP 182/71At speeds over 1300 rpm, the control pipe B adjusting piston opens and the chain tensioner is pressed downwards into the torque position. This alters the change point of the timing chain and the inlet camshaft opens and closes the valves earlier.At speeds above 3600 rpm, the chain tensioner is switched back to the performance position.33 1.8-ltr. 5V Engine AGNSystem overview, Motronic M 3.8.2 SensorsMotronic control unit J220 Air mass meter G70Engine speed sender G28Hall sender G40Throttle valve control unit J338with Throttle valve potentiometer G69 Throttle valve positioner potentiometer G88 Idling speed switch F60Intake air temperature sender G42Coolant temperature sender G62Lambda probe G39Wiring for diagnosis and immobiliserKnock sensor 1 G61 Knock sensor 2 G66 Additional signals:Road speed sensor Air conditioner - ready Signal for engine intervention34 ActuatorsFuel pump G6 Fuel pump relay J17Injectors N30-N33Output stage N122 and ignition coils N/N128Activated charcoal filter solenoid valve 80Lambda probe heater Z19Throttle valve control unit J338with throttle valve positioner V60Variable valve timing valve 1 N205Additional signalsAir conditioner - switch-off Throttle valve potentiometer signal Engine speed signal Fuel consumption signalSSP 182/4635 1.8-ltr. 5V Engine AGNSelf-diagnosisFaults can be evaluated using fault reader V.A.G 1551 or 1552.V.A.G - EIGENDIAGNOSE 01 - Motorelektronik HELP1 2 3 4 5 6 7 8 9 C 0 QHELPPRINTV.A.G 1551SSP 182/39The following functions can be checked by the self-diagnosis using the address word:V.A.G - EIGENDIAGNOSE 01 - MotorelektronikHELP01 - Interrogate control unit version 02 - Interrogate fault memory 03 - Final control diagnosis 04 - Initiate basic setting 05 - Erase fault memory 06 - End of output 07 - Encode control unit 08 - Read measured value blockYou can find explanatory notes on self-diagnosis and address words in the Workshop Manual.36 The colour-coded components are checked during self-diagnosis.SSP 182/9137 1.8-ltr. 5V Engine AGNFunctional diagram, Motronic M3.8.230 15J17 S S S SλZ19 G39 G70 N80 N205 N79N30N31N32N3347380586527 25 26121315556659 697462757656636867M V60 F60 J338 G88 G69+°G40G28 G61MG6inout3138 30 15SSABCDEFGHJ61819 J220 602081072322315453271 78N122 G42G66G62 N128P Q31SSP 182/47 Components:Additional signals:F60 G6 G28 G39 G40 G42 G61 G62 G66 G69 G70 G88 J17 J220 J338 N N30 N31 N32 N33 N79 N80 N122 N128 N205 P Q V60 Z19Idling speed switch Fuel pump Engine speed sender Lambda probe Hall sender Intake air temperature sender Knock sensor 1 Coolant temperature sender Knock sensor 2 Throttle valve potentiometer Air mass meter Throttle valve positioner potentiometer Fuel pump relay Motronic control unit Throttle valve control unit Ignition coil Injector, cylinder 1 Injector, cylinder 2 Injector, cylinder 3 Injector, cylinder 4 Heater resistance (cylinder block breather) Activated charcoal filter system solenoid valve 1 Output stage Ignition coil 2 Variable valve timing valve 1A B C D E F G H JEngine speed signal Fuel consumption signal Wiring for diagnosis and immobiliser Road speed signal Air conditioner - switch-off Air conditioner - ready Throttle valve potentiometer signal Signal for engine intervention on automatic gearbox: terminal 50 on manual gearbox: earthColour code: Spark plug connector Spark plug Throttle valve positioner Lambda probe heater Input signal Output signal Positive Earth39 Dummy page 1.9-ltr. TDI Engine EGRNew features of the 1.9-ltr. TDI engine Distributor injection pumpSSP 182/59The distributor injection pump is preset. The flange is press-fitted on the drive shaft and must not be removed.Injector pipes The injector pipes are plastic-coated for anticorrosion protection.Coating Fuel Injector pipeSSP 182/6140 Non-return valveA constant pressure valve is no longer required as before since it is not necessary to maintain a residual pressure in the injector pipe. A non-return valve is used instead. The task of the non-return valve is to prevent excess fuel reaching the injector and cavitation in the injector pipe. See SSP 124.Reverse flow During reverse flow, the valve plate is closed under the force of the compression spring. Fuel flows through the restrictor drilling. This dampens any existing pressure wave.Valve plateCompression springRestrictor drillingSSP 182/60Fuel delivery During fuel delivery, the valve plate is lifted by the fuel pressure and the restrictor drilling becomes ineffective.Valve plateCompression springSSP 182/6041 1.9-ltr. TDI Engine EGRCylinder head coverCylinder head coverBefore, the cylinder head cover gasket was not joined to the cylinder head cover. Two surfaces had to be sealed.Cylinder head cover gasketCylinder headSSP 182/48Cylinder head cover Permanent join Cylinder head cover gasketNow the cylinder head cover is permanently joined to the cylinder head cover gasket. Therefore, only one surface needs to be sealed.Cylinder headSSP 182/63Before you attach the cylinder head cover, please read the Workshop Manual.42 Vacuum pumpThe vacuum pump consists of a rotor and a vane. The vane is made of plastic and has a movable mounting.Air inlet (vacuum connection) RotorExpanding the cavityVaneThe rotor is driven by the camshaft. When the rotor turns, the vane is forced outwards and the cavity expands. The cavity fills up with air, thus producing a vacuum at the air inlet. The vacuum is utilised by the brake servo.SSP 182/64Diminishing the cavityRotor VaneAs the rotor and vane continue to turn, the cavity diminishes. As a result, the intake air is compressed and expelled through the air outlet to the cylinder head. At the same time another cavity forms.Air outletSSP 182/6543 1.9-ltr. TDI Engine EGRSystem overview SensorsNeedle lift sensor G80 TDI control unit J248 Engine speed sender G2840 F/M T-G PBG UR RB ANY PIE GERM .01 21 82 7 .1OW FLAir mass meter G70SS LU HF RC DU1 46 06 49 07Coolant temperature sender G62Sender for intake manifold pressure G71 and intake manifold temperature G72 Clutch pedal switch F36 Brake light switch F and brake pedal switch F47Accelerator pedal position sender F79 Kick-down switch F8 Idling speed switch F60 Wiring for diagnosis and immobiliser Modulating piston movement sender G149 Fuel temperature sender G149Additional signals:CCS switch Air conditioner - ready Terminal DF Road speed sensor Signal for engine intervention44 ActuatorsEngine glow plugs Q6 Engine glow plugs relay J52Valve for exhaust gas recirculation valve N18Charge pressure limitation solenoid valve N75Metering control N146Fuel cut-off valve 109Commencement of injection valve N108 Additional signals:SSP 182/66Glow period control Engine speed signal Air conditioner - switch-off Fuel consumption signal Glow plug coolant Kick-down signal Accelerator pedal position signal45 1.9-ltr. TDI Engine EGRSelf-diagnosisFaults can be evaluated using fault reader V.A.G 1551 or 1552.V.A.G - EIGENDIAGNOSE 01 - Motorelektronik HELP1 2 3 4 5 6 7 8 9 C 0 QHELPPRINTV.A.G 1551SSP 182/39The following functions are checked by the self-diagnosis using the address word:V.A.G - EIGENDIAGNOSE 01 - MotorelektronikHELP01 - Interrogate control unit version 02 - Interrogate fault memory 03 - Final control diagnosis 04 - Initiate basic setting 05 - Erase fault memory 06 - End of output 07 - Encode control unit 08 - Read measured value blockYou can find explanatory notes on the self-diagnostics and address words in the Workshop Manual.46 The colour-coded components are checked during self-diagnosis.40 F/M T-G PBRG BU Y AN PIERGERM .01 21 82 7 .1OW FLSS LU HF RC DU1 6 46 4 90 07SSP 182/9247 1.9-ltr. TDI Engine EGRFunctional diagram30 1530J 322 S A/+85 87SSJ360 J359FBF47 N79 F36CN108N75N18 Q7 Q7A79152917343320 94644 J248752501 27 2513394012 824 11 237769 6771556251G70G72F60/F8 G71G79N109G80 G28 N3148 30 15S86 30SJ52 85 87SE45A/+DEG6236352110194754702245 18414816642228 765364565759 66 80G81G1495 N146MKHFLJGinoutQ631SSP 182/69 Components:Additional signals:E45Cruise control system switch (CCS)F F8 F36 F47 F60 G28 G62 G70 G71 G72 G79 G80 G81 G149 J52 J248 J317 J359 J360Brake light switch Kick-down switch Clutch switch switch Brake pedal switch Idling speed switch Engine speed sender Coolant temperature sender Air mass meter Intake manifold pressure sender Intake manifold temperature sender Accelerator pedal position sender Needle lift sender Fuel temperature sender Modulating piston movement sender Engine glow plugs relay Diesel direct injection system control unit Voltage supply relay Low heater output relay High heater output relay Exhaust gas recirculation valve Charge pressure limitation solenoid valve Heater resistance (cylinder block breather) Commencement of injection valve Fuel cut-off valve Metering control Engine glow plugs Coolant heater elementsA B C D E F G H J K L M OBrake lights Kick-down signal Accelerator pedal position signal Signal for engine intervention Cruise control system voltage supply Engine speed signal Air conditioner - cutoff Air conditioner - ready Glow period control Fuel consumption signal Wiring for diagnosis and immobiliser Terminal DF Road speed sensorN18 N75 N79 N108 N109 N146 Q6 Q7Colour codes:Input signal Output signal Positive Earth49 Test Your KnowledgeJust mark which answers are correct. Sometimes only one answer is correct. However sometimes they all are. 1. What are the advantages of the oil pump? A Wide teeth intermeshing range B Large working area = good intake characteristics C Few moving parts 2. The 1.6-ltr. engine has a twin-path intake manifold. 2a. What does the twin-path intake manifold permit? 2b. How?Hall sender G40 3. When can you assume that the engine valve timing is correct? Please supplement the drawing.4. The task of variable valve timing is to: Please mark the appropriate letters with a cross.A To improve torque in the low to medium speed ranges. To improve performance in the upper speed range.B To improve torque in the upper to medium speed ranges. To improve performance in the lower speed range.C To adjust valve opening and closing times regardless of engine speed. D To adjust the valve opening and closing times depending on engine speed.50 5. This is the non-return valve. 5.a In which of the drawings is the restrictor drilling used? Please enter the appropriate letter in box.ASSP 182/119Fuel flows through the restrictor drilling. The restrictor drilling becomes ineffective.B5.b What is the task of the non-return valve?SSP 182/1207. The vacuum pump consists of a rotor and a vane. The position of the vanes expands and diminishes the size of the cavity. 7.b Please complete and annotate drawings.Expanding the cavityVaneDiminishing the cavityVaneSSP 182/122You can test your knowledge. If you cannot decide how to answer one of the above questions, read through the related section again.SSP 182/12251 GearboxTooth by toothThe reason for “scratching noise“ when shifting the non-synchromesh reverse gear is often the long time which the input shaft requires to run out.Function of reversing brakeWhen reverse gear is selected, the input shaft is braked as a result of synchronising the 5th gear.When reverse is selected, the selector shaft executes a movement which presses the spring-loaded brake disc against the selector shaft lock.Lock Braking discSelector shaftSSP 182/13The spring-loaded brake disc rotates and displaces the selector mechanism for 5th gear. This synchronises the 5th gear and brakes the input shaft.LockBrake discInput shaftSelector mechanism 5th gearSelector fork5th gear wheelReverse gear wheelSSP 182/1852 Reverse is engaged silently.SSP 182/111When reverse gear is selected, synchronisation of the 5th gear is cancelled. The spring-loaded brake disc returns to its initial position.LockReverse gear is engaged.Brake discInput shaftSelector mechanism 5th gearSelector fork5th gear wheelReverse gear wheelSSP 182/17The reversing light switch and the selector shaft lock are combined in a single component.SSP 182/10053 Running GearWell-clamped and . . .Single-bolt clampSSP 182/41The basis of the front suspension is the 15“ running gear with suspension strut and wishbone.• Cast wheel bearing housing with“single-bolt clamp“ • 40 mm caster54 Single-bolt clampSingle-bolt clampThe cast wheel bearing housing is equipped with a “single-bolt clamp“ for the suspension strut. This simplifies renewal of the suspension strut.Outer raceThere is no need for all-round lubrication of the wheel bearing outer race because the cast wheel bearing housing is self-lubricating.Cast iron has a high graphite content which gives it self-lubricating properties.• Special tool:Spreader -3424SSP 182/2040 mm caster The large caster of 40 mm ensures good directional stability.Because the large caster makes steering more difficult, the Audi A3 has power steering as standard.40 mmSSP 182/2155 Running Gear. . . no adjustmentThe rear axle is a torsion beam axle. The dampers and springs are arranged separately, resulting in a large through-loading width of 1005 mm. There is less driving noise in the interior because the dampers are secured by bolts in the wheel housing.Rear axle mounting• Rear axle mounting inclined at anangle of 25° • Wheel bearing: double ball bearingSSP 182/42Rear axle mounting inclined at an angle of 25°Rubber mounting with plastic housingWhen cornering, the lateral forces acting on the suspension alter the track and cause a selfsteering effect of the rear suspension. This is compensated by attaching the rear axle mountings at an angle and including a rubber mounting. This optimises cornering stability.Rear axle mounting25°The rear axle mountings each consist of a rubber mounting in a plastic housing. If the axle is displaced by lateral force, it is supported by inclined bearing pedestal by means of a rubber collar. The rubber mountings correct the track. They must be press-fitted in the correct position.SSP 182/23Rubber mounting Plastic housingSSP 182/93• Special tool: A 42-011056 Wheel bearing: double ball bearingStub axleThe new wheel bearing is a double-row grooved ball bearing (double ball bearing). It consists of the bearing inner races, the balls and the wheel hub, which is also the outer ball bearing surface. The wheel hub is press-fitted onto the stub axle and tightened by means of a double hexagon nut and thrust washer.SSP 182/129It is not necessary to adjust the bearing play. Radial play exists in the bearing. The axial play depends on the tightening torque. When working on the brake, the brake disc can be removed separately whilst the wheel hub remains fitted on the stub axle.Wheel hub Double-row grooved ball bearing = double ball bearingWhen the wheel hub is removed, the wheel bearing is damaged irreparably and must not be re-fitted.• Special tool: 3420Thrust piece 3416/1 Thrust piece 3416/2 Tube 3416/3SSP 182/2457 SteeringLocking teeth and . . .Gap Steering bearing pedestalWhen the clamp is released, a small gap arises between the steering bearing pedestal and the steering tube support.This gap allows rake and reach adjustment.Steering tube supportSSP 182/5344 mm rake adjustmentLocking teeth ClampingThe steering wheel can be adjusted in height by 44 mm via the locking teeth. The selected height is fixed or released using the clamping lever.max. travelSSP 182/5458 45 mm reach adjustmentClamping lever Steering column tubeThe identical gap allows the steering column tube to be adjusted for reach. The selected reach is fixed or released using the clamping lever.SSP 182/55Steering gear lock Dynamic forces and lateral forces act on the steering. The power steering gear is locked to the subframe, preventing it from slipping even if large steering forces are applied.Power steering gear LockSubframeSSP 182/5659 . . . crash-testedThe new crash concept prevents any further intrusion of the steering column and steering wheel into the occupant cell in the event of a collision.Engine compartment bulkheadCentral tubeIn the following pictures, we will show you the measures taken to achieve this.SSP 182/57Force exerted from the frontEngine compartment bulkhead Displaced engine compartment bulkhead Telescopic tube 150The engine compartment bulkhead can be displaced by 150 mm towards the lower end of the steering column without causing damage to the steering column.38Force exerted from below A telescopic tube enables the lower end of the steering tube to be compressed by 38 mm.SSP 182/72Force exerted from the frontTelescopic tubeAnother telescopic tube integrated in the upper section of the steering column enables the steering column to be displaced by 50 mm.Displaced engine compartment50SSP 182/7360 . . . and crash-testedSteering mounting pedestalForce exerted from the front When the driver’s body impacts with the inflated airbag, the steering column is displaced by a further 50 mm over the steering mounting pedestal.50SSP 182/94Steering mounting pedestalThe airbag cushions the the driver and tapered oblong holes in the steering mounting pedestal convert the resulting force into distance.50SSP 182/74The diagram shows a view of the steering mounting pedestal from above.All sizes are given in millimetres.61 Braking systemPower under pressureThe brake discs at the front are ventilated.The cars are equipped with a guide bolted onto the wheel bearing housingora guide cast onto the wheel bearing housing for the brake padsBolted guideCast guideSSP 182/49SSP 182/50Brake disc, rear The standard rear disc brake features an aluminium floating caliper. Advantage: - low weight - good thermal conductivityAluminium floating caliperSSP 182/51Dacrometised bolts All exterior bolts are dacrometised. This coating, which contains zinc-aluminium powder, protects the bolts against corrosion. You can find further information in SSP 160.SSP 182/5262 Test Your KnowledgeQuestions about questions1. Please complete. The cast wheel bearing housing is provided with a .............. ...................................................... for the............ ......................................................... .2. The outer race of the wheel bearing must be greased.YesNo3. Please complete.Each of the rear axle mountings comprises a.............................. with ............................ .3a. What are the advantages of this?3b. Please complete.The rear axle mounting must be press-fitted into........................................................................ .4. State the advantages of the new double ball bearing.5. What purpose does the steering gear lock?63 Dash panel insertThe command centreThe immobiliser control unit is integrated into the printed circuit board of the dash panel insert. The immobiliser self-diagnosis can be activated using the address word “17 Dash panel insert“.901/2 120 °C R 1/14 3 2 5 65010080120ABS140P16018020060!AIR BAG40220km/h0km171/min x 10002024026013 8.84D0 000 190SSP 182/101Self-diagnosisV.A.G - EIGENDIAGNOSE 17 - SchalttafeleinsatzHELP1 2 3 4 5 6 7 8 9 C 0 QHELPPRINTThe following functions can be checked in the data transmission mode using the address word “17 Dash panel insert“:V.A.G 1551SSP 182/7801 02 03 04 05 06 07 08 10 11- Interrogate control unit version - Interrogate fault memory - Final control diagnosis - Initiate basic setting - Erase fault memory - End of output - Encode control unit - Read measured value block - Adaptation - Log-in procedure64 Notes65 AnswersPages 14 and 151. 1. B CPage 50Subsection 1 Subsection 2 Subsection 32a. The twin-path intake manifold enables the intake path length to be adapted to meet engine demands.SSP 182/82. 3.by the side members ... high-strength extruded aluminium sections. large amounts of energy...2b. By the position of the change-over flap. It can create long and short intake paths.4. ... pelvis and rib areas of the body... 5. 6. A C 3.58 61 88 118 1 28 58 61SSP 182/107One of the films consists of an electrically conductive polymer.Negative electrode Falling edgeTooth gap 119+120Rising edgeSSP 182/106Positive electrode4.ADThe other film contains an interrupted electric circuit with several positive and negative electrodes.7.... pressure is exerted on the electrically conductive film. The resistance is low.66 Page 515a.Page 631. ... Single-bolt clamp for the suspension strut ...A BFuel flows through therestrictor drilling. 2. the restrictor drilling becomes ineffective. 3. ... Rubber mounting with plastic housing No5.b The task of the non-return valve is to prevent excess fuel injection at the injector and cavitation in the injector pipe.3.a Good self-steering response and silent running3.b ... for a specific direction... 7.b Expanding the cavity 4. self-aligning; long service lifeRotor Vane5.It prevents the steering gear from slipping when full steering lock is applied.SSP 182/647.b Diminishing the cavityVane RotorSSP 182/6567 Notes68 With the Audi A3, Audi has achieved an ideal blend of safety, engineering, comfort and sportiness.A car which meets discerning standards.SSP 182/110