TECHNICAL DOCUMENTATION
SSP 891403 The new Jetta New Model Introduction

This PDF is currently unavailable.
Read document text
The new Jetta New Model IntroductionSelf-Study Program Course Number 891403Volkswagen of America, Inc. Volkswagen Academy Printed in U.S.A. Printed 12/2004 Course Number 891403 ©2004 Volkswagen of America, Inc. All rights reserved. All information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or other wise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Volkswagen of America, Inc. Always check Technical Bulletins and the latest electronic repair information for information that may supersede any information included in this booklet. Trademarks: All brand names and product names used in this manual are trade names, service marks, trademarks, or registered trademarks; and are the property of their respective owners.Table of ContentsIntroduction ................................................................................1 Course Introduction, The New Jetta Body ............................................................................................6 Chassis Construction, Exterior Parts, Windows, Hood Latch Cable, New Door Design, Seat Design Features, Storage Areas Passenger Safety ......................................................................20 Overview, Two-Stage Airbags, Advanced Airbag System, Active Front Seat Head Restraints, Rear Side Head Airbags, Side Airbag Crash Sensors Engines ......................................................................................26 2.5L/150 HP 5-Cylinder Engine with 4-Valves per Cylinder, 2.0L/200 HP 4-Cylinder Turbo FSI Engine with 4-Valves per Cylinder, 1.9L/105 HP TDI Engine with 2-Valve Technology, Pedal Assembly Automatic Transmission ...........................................................52 6-Speed Direct Shift Gearbox (DSG) 02E, 6-Speed Automatic Transmission 09G Suspension ...............................................................................54 Suspension Features Electrical System ......................................................................56 Fuse and Relay Locations, CAN Networking Concept, Air Conditioning Systems Heating and Air Conditioning .................................................62 Introduction, Air Distribution System, Overview of the Dual Zone Climatronic/Climatic System, Sensors, Actuators Radio and Navigation ..............................................................75 Radio and Navigation Systems Service .......................................................................................77 Special Tools, New Special Tools Important/Note!This Self-Study Program covers the design and operation of the new Jetta! This Self-Study Program is not a Repair Manual. This information will not be updated. For testing, adjustment and repair procedures, always refer to the latest electronic service information.New!iIntroductionCourse IntroductionThe new Jetta continues its success story of the past 30 years. The new Jetta introduces new features that combine appearance with comfort and modern technology, resulting in a vehicle that provides the ultimate value in its class. Attention to detail, increased horsepower, added safety features and subtle quality improvements set the new Jetta apart from the competition. The new Jetta is built at Volkswagen's Puebla, Mexico plant. This plant began operation in 1964, manufacturing the old style Beetle. Currently, the Puebla plant employs approximately 14,000 people and also produces the New Beetle, among other vehicles. New Jetta features include: • Elegant design • • • • • • • Superior quality Excellent handling dynamics Comprehensive safety package Innovative drivetrain technology Improved economy Spacious interior Customer focused innovationsAdditional self-study programs relating to the new Jetta include: • • • • • SSP 851503: 6-Speed Automatic Transmission 09G/09K/09M SSP 851403: The Direct Shift Gearbox 02E SSP 892403: The Electro-Mechanical Power-Assisted Steering SSP 873403: The new Jetta–Electrical System Design and Function SSP 861403: The new Jetta–Steering and Suspension1IntroductionThe New JettaThe new Jetta sets new standards for its class in many areas, including: • Safety • • • • • Quality Design Handling Roominess Drivetrain • Premium sound system•Many storage locations such as the overhead console•Electro-mechanical power steering•2.5L 150 HP 5-Cylinder Engine with 4-Valves per Cylinder•Optional Bi-Xenon headlights•ABS/ESP MK 602IntroductionOther Features • Rain sensing windshield wipers • Optional rear distance warning system•Dual zone climate control•Two piece tail light design•Four link independent suspension•Customer personalization via the multi-function indicator (MFI) switch leverS891403_1023IntroductionTechnical Specifications The figure shows the dimensions of the front-wheel drive new Jetta.Weights and Exterior Dimensions34.6 in. (880mm)101.5 in. (2578mm) 178.1 in. (4523mm)42.7 in. (1084mm)S891403_1657.5 in. (1,461mm)60.4 in. (1,533mm) 69.1 in. (1,755mm)59.7 in. (1,517mm)S891403_15Length Width Height Wheelbase178.1 in. (4,523mm) 69.1 in. (1,755mm) 57 .5 in. (1,461mm) 101.5 in. (2,578mm) S891403_01Front track width Rear track width Maximum weight Empty weight60.4 in. (1,533mm) 59.7 in. (1,517mm) 4,057 to 4,321 lb.* (1,840 to 1,960 kg) 3,016 to 3,331 lb.* (1,368 to 1,511 kg) *varies depending on model S891403_024IntroductionInterior Dimensions12S891403_1237 .4 to 38.4 in. (949 to 975mm) 37 .0 to 37 .2 in. 2 Back seat headroom (941 to 945mm) *varies depending on model S891403_03 1 Front seat headroom5BodyChassis ConstructionStatic and Dynamic Rigidity The new Jetta sets new standards for static and dynamic rigidity by the application of lightweight design principles. Fenders, doors and side panels are all made of high strength steel. Laser Weld Technology The assembly plant in Puebla, Mexico makes extensive use of laser welding technology to produce the new Jetta chassis. The increased use of laser welds has resulted in significant improvements in chassis strength and rigidity. Laser weld technology not only improves manufacturing efficiency, it also improves the quality of the chassis by increasing the welded surface while reducing the deformation of the sheet metal caused by the necessary heat and pressure of previous welding methods. The chart below provides a comparison of increased manufacturing technology on the new Jetta A5 compared to the previous Jetta A4.Key: Red Yellow Blue= Side Impact Zone = Occupant Cell = Frame Structure6BodyB-pillar The new Jetta’s B-pillar consists of three hot formed panels that provide improved passenger protection in the event of a side-impact collision.B-pillarOuter Body Side PanelS318_066 Inner Body Side Panel (tailored blank)Hot Formed Panels The B-pillar and adjacent portion of the body in the direction of the A-pillar are heat treated during the forming process to increase strength. These hot formed panels are stronger and weigh less than the panels on previous models.Hot formed panelsS891403_19S891403_18 Additional side impact protection in doorsS891403_177BodyExterior PartsImpact-Absorbing FoamFront Bumper By integrating an impact-absorbing foam element into the front bumper behind the front spoiler, the risk of injury to pedestrians is reduced. This deformable foam element allows compression of the front bumper during impact.S318_289Headlights The Jetta headlights feature clear glass. The turn signals are located below the low and high beam headlights to improve their visibility to other drivers. Bi-Xenon headlights are available as an option on some models.S891403_1158BodyExterior Rearview Mirrors Turn signals are integral to the exterior rearview mirrors. Tail Lights The new Jetta has two-part tail lights.S891403_117 S891403_116S891403_269BodyWindowsThe windows on the new Jetta are greentinted glass (blue-tinted glass will be available at a later date). The thickness of the window glass depends on its location: the windshield is .17 inches (4.4mm), the front side windows are .14 inches (3.5mm) and all other windows are .12 inches (3.15mm). All fixed windows are bonded to the body. Windshield The windshield is available with an infraredreflective metal vapor deposition coating. This coating reflects most of the sun’s heat generating infrared rays. Conventional reflective glass shields a vehicle’s interior from far less solar radiation by absorption. Always set the windshield on its side. Otherwise, the sash at the bottom and/or the sealing lip at the top can become damaged.Sealing Lip Drip Molding AreaCeramic Coating as Third Sun Visor Clear Area for Rain/Light SensorsWindshield LabelDrip Molding AreaS318_003 Area Below the Hood Sash for Plenum Chamber Cover Clear Area for VIN Plate10BodyRear Window Replacement rear windows are produced with integral diversity antennas. Diversity antennas connect to the diversity switching box by two terminals on the window. Signals are relayed simultaneously from these terminals to the radio and the diversity switching box. Using both antenna signals significantly reduces interference.Heater element with additional printed conductors for optimizing the rear window antennas Antenna TerminalAntenna TerminalS318_005 Heater Element Terminal Heater Element TerminalBe sure to order the correct rear window when replacing to assure all electrical terminals are present.11BodyHood Latch CableThe hood latch cable (bowden cable) for releasing the hood latch from inside the passenger compartment is located in a protected area in the engine compartment. The hood latch cable disconnect point is located under the hood behind the driverside headlight assembly. This allows front end service without removing the cable from the vehicles interior.S891403_47Disconnect point (closed)S318_251Disconnect point (open)S318_253Bowden cable disconnectedS318_25512BodyEmergency Release Mechanism Removing the interior trunk trim allows access to the locking linkage for emergency release of the trunk.S891403_46S891403_10413BodyNew Door DesignThe doors on the new Jetta consist of an outer panel with two mounting rails and an inner section for mounting hardware. The door’s outer panel is bonded to the mounting rails that are bolted to the inner section. Removal of the outer door panel allows access to some of the door’s inner hardware and electronics, the window motor is accessed through the inside. Also, in the event of door damage, the outer panel can be removed for repair or replacement. Check the current service repair information for instructions on outer door panel removal.Door Inner SectionCover StripMounting RailCover StripDoor Outer PanelMounting Rail Side Impact Bar S318_25714BodyMounting Rails The mounting rails are permanently bonded to the outer panel with adhesive. This ensures an accurate fit when the outer panel is bolted to the door's inner section.Mounting RailsDoor Outer PanelS318_203Internal Door Components Removing the outer panel allows easy access to the side impact bars, door handle bracket, door lock, side airbag crash sensor and the window regulator module.Door Handle BracketDoor Lock Window Regulator Module S318_205 Driver’s Side Airbag Crash Sensor G179Side Impact Bars15BodySeat Design FeaturesFront Seats The front seats on the new Jetta are equipped with an active head restraint system. Options include: a mechanical 2-way lumbar support or an electrical 4-way lumbar support. The active head restraint system is a mechanical system that moves the driver and passenger head restraints upward and forward in the event of a rear end collision.S891403_94 1. 2. 3. 4. 5. 6. Through-Loading Front Passenger Seat Rear Loading Door Active Head Restraints 4-Way Lumbar Support Power Backrest Complete Power Seat, OptionalActive Head Restraint System S891403_118 Power Backrest Height Adjustment 4-Way Lumbar SupportS318_060 S891403_119 4-Way Lumbar Support16BodyAn optional feature of the front passenger seat allows it to be folded flat for loading and hauling of long items by using the full length of the interior. On vehicles equipped with the pass-through option for the rear seat, the armrest and the door located behind it can be folded forward to allow transport of long items such as skis or golf bags.S318_101Rear Seats The rear seat cushion extends across the full width of the interior. The backrest is split 60/40 and can be folded down. The backrests lock using a rotary latch. A red indicator shows if the backrests are locked or not.S318_209 The pass-through door is locked in position.S318_211 A red indicator showing means that the pass-through door is not locked in position.S318_207 A red indicator showing means that the backrest is not locked in position.17BodyStorage AreasThe new Jetta features numerous convenient storage areas. Front Storage Vehicles equipped with air conditioning can cool the front passengerside storage compartment.Adjustable Temperature OutletS318_103Overhead Storage There is a standard open storage compartment in the overhead console of the new Jetta.Door Storage Storage compartments, and a cup holder for 1.6 quart (1.5 liter) bottles are located in the door panels.S318_105S891403_4718BodyCenter Console Storage A new Jetta storage option includes an airconditioned storage compartment in the center console and fold-out cup holders for the rear seats.Rear VentS318_155 Rear Fold-Out Cup HolderAdjustable Temperature OutletS318_081 Storage Compartment DoorTrunk Storage A sliding cover provides access to a side compartment for storing small objects. Removal of the sliding cover allows parallel storage of larger items such as a golf bag.Spare Tire Area Storage The new Jetta is equipped with a full-size emergency spare tire. There are additional storage areas near the spare tire location.S891403_5319Passenger SafetyOverviewThe new Jetta provides the following protection systems/devices. Standard protection equipment includes: • Driver and front passenger two-stage airbags • • • • • Front seat side curtain airbags Front and rear side (head) airbags 3-point seat belts on all seats Front seat belt tensioners and belt force limiters Front seat active head restraint system.Side Curtain Airbag with Gas Distributor Tube S318_153Optional protection equipment includes: • Rear passenger side (head) airbags in combination with belt tensioners and belt force limiters on the outer rear seats.Two Longitudinal Acceleration Sensors (Early Crash Sensors) G251, located in the front of the vehicle, detect impact and impact intensity.S318_153 Lateral acceleration sensors, located in the rear wheel housing, detect side impacts.Airbag Control Module J234 receives data from the sensors and controls airbag deployment.Pressure Sensors G179 and G180 in the front doors detect sudden changes in air pressure during a side impact.S891403_24 S318_12520Passenger SafetyThe driver and passenger airbags provide two-stage deployment. The front passenger airbag is activated or deactivated automatically via the Advanced Airbag System. Side curtain airbags cover the window area from the A-pillar to the C-pillar. In the event of a crash, a pressurized gas cylinder provides uniform inflation of the curtain airbags. The rear outer seats are equipped with child seat anchors as standard equipment.Front Seatbelt Pretensioner Advanced Airbag System Passengerside Two-Stage Airbag Curtain Airbag Side Airbag Side Impact Pressure Sensors Side AirbagFront Impact SensorsS891403_92 Airbag Driverside Control Two-Stage Module Airbag Seatbelt Engagement Detector Switch Rear Seatbelt Pretensioners Rear Side Impact Sensors21Passenger SafetyTwo-Stage AirbagsThe airbag system reacts to unique crash conditions by deploying the driverside and passengerside airbags in two stages, depending on the size of the front seat occupants and the severity of the impact.S891403_95Advanced Airbag SystemSeat Belt SensorThe new Jetta is equipped with the Advanced Airbag System. This system is a Bladder standard feature for the front passenger Pressure seat. Based on occupant weight and Sensor seatbelt tension, the system signals the control module to deploy the airbag in one Hose of two stages. In a slow speed collision, the two-stage airbag and the Advanced Airbag Protection System work together to activate only the first stage. This provides the best protection Felt for a small adult. The “Passenger Airbag Electronic OFF” light is illuminated when the Control Module passenger seat is unoccupied.S891403_96PASSENGER AIR BAG OFFS891403_9722Passenger SafetyActive Front Seat Head RestraintsThe new Jetta is equipped with active head restraints on the front seat. During a collision, as the occupant is pressed back into the seat, the head restraint is activated and moves forward and down to minimize head and neck injuries. At the same time that the head restraint is activated, the lumbar support moves forward to provide additional protection from injury. This is a completely mechanical system that requires no electronics.Movement of Head RestraintsS891403_9823Passenger SafetyRear Side (Head) AirbagsAirbag ModuleThese airbags are available as an option for the outer rear seats. They are located in the side bolsters. Seat Belts The front seatbelts are equipped with pyrotechnic tensioners and belt force limiters. The front seatbelts also have adjustable belt guides to improve passenger comfort. The rear outer seats on vehicles equipped with rear side head airbags also have belt tensioners and belt force limiters. Retractors are attached to the body to improve passenger shoulder comfort. The rear center seat has a three-point seatbelt with a retractor integrated in the backrest.Rear Side CushionS318_016 The driverside seatbelt is located in the B-pillar.S318_21324Passenger SafetySide Airbag Crash SensorsThe Driverside Airbag Crash Sensor G179 and the Front Passengerside Airbag Crash Sensor G180 replace the conventional acceleration sensors for side impact detection. These new pressure sensors provide faster detection of side impacts in the door area. Sensor Function The side airbag crash sensors are located in the front doors between the inner and outer body panels. These sensors react to changes in air pressure in the door cavity. Air is directed via an inflow duct to a plate. The components on the plate react to rapid changes in air pressure that occur during a crash. Sensor Signal The sensor continuously monitors air pressure in the door cavity. If the sensor detects a rise in air pressure above a predetermined value, it sends a signal to the airbag control module. Sensor Failure If the sensor fails, the airbag warning lamp, located in the instrument cluster, will come on.Air Inflow Duct Sealing CompoundBlankContactsS318_127 Housing25Engines2.5L/150 HP 5-Cylinder Engine with 4-Valves per CylinderThe 2.5L/150 HP engine has 5 cylinders and 4 valves per cylinder driven by DOHC. This engine is all new for the new Jetta and offers high torque, high performance, low fuel consumption, low emissions and low maintenance. Special Features: • Transverse 5-cylinder design • • • • • Dual overhead cams Continuously variable intake cam Chain driven cams Roller rocker fingers No hazardous materials used in components Torque and PowerBGP 5-cylinder in-line engine 151 cu. in. (2480cc) 1-2-4-5-3 3.25 in. (82.5mm) 3.65 in. (92.8mm) 4 10:1 150 HP (110 kW) at 5,000 rpm 168 ft. lb. (228 Nm) at 4,000 rpm 94 octane (98 RON) unleaded fuel, 91 octane (95 RON) unleaded can be used with reduced performance Catalytic converter SULEV ULEV2S891403_33Technical DataEngine code Type Displacement Firing Order Bore Stroke Valves per cylinder Compression ratio Max. output Max. torque Fuel184335147268Torque (Ft. Lbs.)111201741343767Exhaust gas treatment Emissions standardS891403_3110003000 5000 Engine Speed [rpm]7000 S891403_3226HorsepowerEnginesEngine Block The 2.5L engine block design is similar to previous models with an improved lubrication system. Engine Crankshaft The crankshaft is made of forged steel with bearing and connecting rod surfaces like the 2.0L engine and includes the timing gear. The five connecting rod locations are equally positioned at 72°.S891403_134S891403_132 Oil Filter Bypass Passage Oil Filter PassageThree Oil Return Check Valves (Open Above 43.5 psi)S891403_133 Four Open Oil Return Passages27EnginesDual Overhead Cam Head The A5 engine has dual overhead camshafts with a continuously adjusting intake cam. The head design is based on the V10 Lamborghini engine.Advance ChamberRetard ChamberS891403_123Assembled Camshaft (Lower Weight)S891403_135Roller Cam FollowerS891403_13128EnginesTiming Chains The 2.5L engine uses timing chains to improve durability and extend service periods. The timing chain arrangement also drives the oil pump and the vacuum pump through its intermediate cog wheel.Intake Camshaft Exhaust CamshaftVacuum PumpCrankshaft Oil Pump S891403_12429EnginesIntake Manifold The intake manifold on the 2.5L A5 engine is made of plastic. The intake manifold assembly includes the throttle body, fuel regulator, AKF valve and the pressure and throttle sensor assembly.Exhaust Manifold A feature of the 2.5L exhaust manifold is its isolated air-flow design. The exhaust manifold features a protective plate that serves as a source for heated intake air.S891403_128Heated Air to the Intake SystemProtective PlateS891403_127S891403_12630EnginesEngine Cover/Air Filter Housing The engine cover on the 2.5L engine includes the intake air filter and part of the system that delivers heated intake air to the engine. The engine cover’s configuration also lowers engine noise.S891403_129S891403_130Vacuum Pump The 2.5L engine’s vacuum pump is mechanically driven by the timing chain and provides power assist to the vehicle’s brake system. The pump is driven via its cog wheel assembly.Vacuum PumpCog Wheel AssemblyS891403_12531EnginesEngine Control System–Input/Output DiagramG71 G28 G40Relay 458 (87) N80Relay 167 G79 G185 G187 G188 G61 G66 G186 N29 N70 N127 N292 N323N205 G62 G83 F F47 G39 G130 G465 G476 G70 G42 K Additional Signals Vel. Cruise Climate DFM Alternator PWM Ventilators N112 V101 J299 N30 N31 N32 Z19 Z29 Z30N33 N83V144 Pump LDPJ519, J533, J527 , J234, J104, J285, J217Additional Signals VentilatorsS891403_13632EnginesCrankshaft Seal Flange with Integrated Engine Speed Sensor Wheel The crankshaft seal flange with integrated engine speed sensor wheel is a new feature. The crankshaft seal flange seals the cylinder block on the flywheel end. The seal is made of heat-resistant and nonwearing polytetrafluoroethylene (PTFE) plastic. The engine speed sensor is a Hall effect sensor mounted in the crankshaft seal housing and consists of a steel ring mounted in rubber. This rubber material contains embedded magnetized metal chips that have an alternate north and south polarity with a large north pole to serve as a reference for the engine speed sensor. The sensor wheel is precisely press-fit into the crankshaft flange.Crankshaft Seal FlangeS318_051 Engine Speed Sensor Engine Speed Sensor WheelNorth Pole South Pole S318_04933Engines2.0L/200 HP 4-Cylinder Turbo FSI Engine with 4-Valves per CylinderThe 2.0L turbo FSI engine combines the advantages of direct injection combustion with exhaust turbo charging technology. The result is an extremely responsive engine.S891403_71Technical DataTBD 4-cylinder in-line engine 121 cu. in. (1984cc) 1-3-4-2 3.25 in. (82.5mm) 3.65 in. (92.8mm) 4 10.5:1 200 HP (147 kW) at 5,000 rpm 207 ft. lb. (280 Nm) at 1,800 to 4,700 rpm Engine management Bosch Motronic MED 9.1 94 octane (98 RON) unleaded Fuel fuel, 91 octane (95 RON) unleaded can be used with reduced performance Inner EGR Exhaust gas recirculation Emissions standard ULEV Engine code Type Displacement Firing Order Bore Stroke Valves per cylinder Compression ratio Max. output Max. torqueS891403_90Torque and Power236 207 177 148 118 89 59 30 218 190 163 136 109 82 54 27 1000 3000 5000 7000 Engine Speed [rpm] S891403_91Torque (Ft. Lb.)34HorsepowerEnginesCrankshaft The crankshaft has been modified to meet the tougher demands of the turbo FSI engine. This results in higher strength components and less engine noise. The main bearing flanges and journals have been enlarged for more strength. This meets specifications even with the .25 in. (6.4mm) increase in stroke.332_020 Flanges35EnginesEngine Balancer Shaft The balancer shaft gear used in the engine features the following: • Separate gear and imbalance masses to improve balancing • • Oil pump with wider gear Clean oil controlled pressure regulator with pressure control on the raw oil side close to the oil pump, integrated in the balancer shaft housing Higher strength die-cast housing Balancer shafts mounted in the aluminium housing Decoupled final drive sprocket in the balancer shaft drive gearIntake Line Final Drive Sprocket Oil Pump Drive GearCrankshaftImbalance Gears Balancer Shaft Housing Balancer Shafts• • •332_02136EnginesFinal Drive Sprocket High torsional irregularities from the crankshaft of the turbo engine at low RPMs results in greater chain forces in the balancer shaft chain drive. The crank oscillation angle of the turbo engine is 2°. Bow springs have been integrated into the sprocket wheel hub. They decouple the input shaft of the balancer shaft module from the crankshaft. This is similar to a dualmass flywheel.Diamond-Coated Disc Hub Plain Bearing Bow Spring (2x) Sprocket WheelFriction Disc Diaphragm Spring Cover Disc332_02237EnginesToothed Belt Drive As with all 4-cylinder in-line engines, the timing gear drives a toothed belt that drives the exhaust camshaft. The toothed belt tensioning system has been modified to meet the demands placed on the toothed belt drive by the turbo, including: • Higher valve spring pressures • Turbo-related valve timing associated with the 42° crank angle adjustment range of the continuous variable valve timing on the intake camshaft High-pressure oil pump drive from a triple cam on the intake camshaft The new Crankshaft Torsional Cancellation (CTC) toothed belt sprocket reduces camshaft vibration and the forces acting on the toothed belt.Function•The toothed belt sprocket is positioned on the crankshaft at TDC of cylinder 1, as shown below. When the cycle begins, forces acting on the toothed belt are reduced by the elliptical shape of the toothed belt sprocket. The flat side of the sprocket gear allows a slight slackening of the toothed belt.The modification is an elliptical toothed belt sprocket on the crankshaft.D2D1D2D1S891403_7638EnginesCylinder Head The cylinder head features the following: • Sodium-filled exhaust valves • • • Intake valves with reinforced seats Roller rocker fingers strengthened while reducing cam and roller land width Identical valve springs are used for both intake and exhaust valves Intake port geometry is used to enhance the tumble effect, reduce knock and improve running smoothness.2.0L 4V T-FSI332_01739EnginesCrankcase Ventilation A constant vacuum is maintained in the crankcase through separate ventilation of the crankcase and cylinder head. The crankcase breather is connected to the intake manifold. The crankcase blow-by gases flow into the cylinder head through the primary oil separator in the oil filter module. Here the blow-by gases mix with the gases from the cylinder head and flow through a second separator to provide additional oil separation. Since a turbo engine requires a more sophisticated pressure control system, a two-stage pressure control valve is located on the cylinder head cover. If vacuum exist in the intake manifold, blow-by gases flow directly into the intake manifold. If a boost pressure is present in the intake manifold, a one-way valve in the pressure control valve housing closes and the blowby gases flow into the cylinder head cover ahead of the turbocharger. The system can detect faulty installation of the pressure control valve. Unmetered air is detected by the reaction of the lambda probe.If a boost pressure is present upstream of turbocharger If a vacuum is present in the intake manifold Exhaust Turbocharger Gas OutletIntake Manifold Gas Outlet Valve CoverCentral Crankcase Gas Inlet Oil Filter ModuleNon-Return ValvePressure Control ValveNon-Return Valve332_05740EnginesExhaust Turbocharger/Manifold Module To conserve space and improve performance and serviceability, the exhaust manifold and turbine housing have been combined into a single module. Special emphasis was placed on easy removal and installation of the exhaust manifold and the close-coupled catalytic converter. The turbine shaft mount is integrated into the compressor housing. The air intake includes connections for crankcase and ACF ventilation. A silencer reduces pressure pulsation noises. Boost pressure is controlled by a Wastegate Bypass Regulator Valve N75. A Turbocharger Recirculating Valve N249 prevents “overbraking” of the turbine when the engine is in overrun with the throttle valve closed and boost pressure still present. The Wastegate Bypass Regulator Valve N75 and the Turbocharger Recirculating Valve N249 are located on the turbocharger.Crankcase Breather Connection Coolant Flow to Radiator or From Auxiliary Water Pump ACF Connection Pressurized Oil InletTurbocharger Recirculating Valve N249Coolant Inlet From Engine Block 332_02441EnginesA clamping flange on the cylinder head allows easy removal and installation of the exhaust turbocharger/manifold module. The terminal block does not require removal.Terminal Block332_025The exhaust manifold is split. A divider in the manifold ensures a steady flow of exhaust gases to the turbine. The ports of cylinders 1 and 4 and cylinders 2 and 3 are separated based on the firing order. The divider also prevents the exhaust gas pressure from expanding into the other cylinders. This maintains turbine speed and optimizes turbocharger response.Cylinder 1Divider332_02642EnginesCharge Air Ducting and Boost Pressure Control The boost pressure and intake pressure are converted to control pressure by the pulse width modulated Wastegate Bypass Regulator Valve N75. Control pressure acts on the pressure unit that actuates the wastegate flap. The wastegate flap opens a bypass and allows some of the exhaust gases to flow past the turbine wheel into the exhaust system. This control system regulates the turbine speed and sets the maximum boost pressure.Turbocharger Recirculating Valve N249 Wastegate Bypass Regulator Valve N75 Pressure Unit Wastegate Brake Booster ServoIf the control system fails, the boost pressure acts directly on the pressure unit. The increased spring pressure reduces maximum boost down to minimum boost.Vacuum PumpWater ConnectionEvaporative Emission (EVAP) Canister Purge Regulator Valve N80 Oil Filter ModuleCharge Air Cooler332_01143EnginesOverrun Air Divert Control If the throttle valve closes when the engine is in overrun, back pressure develops in the turbo housing. Back pressure reduces the speed of the turbine, which reduces boost pressure and increases turbo lag. To avoid this, the Turbocharger Recirculating Valve N249 is opened by an electrical actuator. This allows the compressed air to flow back to the intake side of the circuit through the turbine. This maintains turbine speed. The Turbocharger Recirculating Valve N249 closes when the throttle valve opens again and boost pressure is immediately available.Overrun ModeAir Intake From Air FilterDivert Air Valve Open Engine Running Under LoadDivert Air Valve Closed332_01244EnginesCooling System To prevent carbon build-up on the turbine shaft in the turbocharger, an auxiliary water pump provides additional water circulation for up to 15 minutes after the engine is shut off hot. The pump forces the lower temperature coolant against the normal direction of flow. The coolant flows from the radiator through the turbocharger to the engine block and back to the cooler.Connection Expansion TankConnection Heat ExchangerEngine Block ConnectionWater Port Connection Exhaust-Driven TurbochargerCoolant ThermostatRadiator Outlet Oil Cooler Auxiliary Water PumpRadiator Inlet332_02845EnginesTumble Flaps At different engine rpms, tumble flaps are activated to enhance the air/fuel mixture. The tumble flaps are actuated: • To improve cold engine idling • • To improve charge efficiency at start-up In overrun modeHigh-Pressure Rail Plastic Flap with Steel ShaftHigh-Pressure/ Low-Pressure Fuel PortIntake Air Temperature SensorThrottle Valve Actuator Activated Charcoal Filter Valve332_058 Tumble Flap ActuatorPressure Limiting ValveACF System with Double Non-Return Valve46EnginesFuel Supply Fuel for the 2.0L direct-injection engine is supplied by a demand-controlled fuel pump. This demand control was developed to reduce the demands on the fuel pump and improve fuel economy. The fuel pump maintains system pressure but only supplies as much fuel as the engine requires. The Engine Control Module (ECM) and an electronic power module control fuel pump speed through pulse width modulation.Fuel Pressure Regulator Valve N276 Triple Pump Cam High-Pressure Injector High-Pressure Pump Low-Pressure Fuel Circuit Low Fuel Pressure Sensor G410 High-Pressure Fuel Circuit Pressure Limiting Valve 332_073 Fuel Pressure Sensor G247Fuel Demand Control System Electronic Power Module ECMFuel Filter With Pressure Limiting ValvePressure Sensor 0.5-5 BarShort Return LinePressure Sensor Rail Pressure 50-110 Bar Pressure Control Valve For Pressure Exceeding 120 Bar Injectors Injector System 332_078Suspension Strut Turret Fuel Delivery Module With Fuel Tank Sensor Electrical Fuel Delivery47EnginesActuators and Sensor Diagram Mass Air Flow (MAF) Sensor G70 Charge Air Pressure Sensor G31 Manifold Absolute Pressure (MAP) Sensor G71 Engine Speed (RPM) Sensor G28 Camshaft Position (CMP) Sensor G40 Throttle Drive Angle Sensor 1 [for Electronic Power Control (EPC)] G187 Throttle Drive Angle Sensor 2 [for Electronic Power Control (EPC)] G188 Throttle Valve Control Module J338 Throttle Position (TP) Sensor G79 Accelerator Pedal Position Sensor 2 G185 Brake Light Switch F Brake Light Switch F63 Fuel Pressure Sensor G247 Intake Manifold Runner Position Sensor G336 Knock Sensor (KS) 1 G61 Knock Sensor (KS) 2 G66 Engine Coolant Temperature (ECT) Sensor G62 Engine Coolant Temperature (ECT) Sensor (on Radiator) G83 Low Fuel Pressure Sensor G410 Intake Air Temperature (IAT) Sensor G42 Heated Oxygen Sensor (HO2S) G39 Oxygen Sensor (O2S) Behind Three Way Catalytic Converter (TWC) G130 Exhaust Gas Temperature (EGT) Sensor 1 G235 Clutch Position Sensor G476 Alternator DFDiagnosis Connection Barometric Pressure (BARO) Sensor F96 Motronic Engine Control Module J220S891403_8848EnginesCruise control On/Off Fuel Level Sensor G Transfer Fuel Pump (FP) G6 Cylinder 1 Fuel Injector N30 Cylinder 2 Fuel Injector N31 Cylinder 3 Fuel Injector N32 Cylinder 4 Fuel Injector N33 Ignition Coil 1 with Power Output Stage N70 Ignition Coil 2 with Power Output Stage N127 Ignition Coil 3 with Power Output Stage N291 Ignition Coil 4 with Power Output Stage N292 Throttle Valve Control Module J338 Throttle Drive [for Electronic Power Control (EPC)] G186 Motronic Engine Control Module (ECM) Power Supply Relay J271 Engine Component Power Supply Relay J757 Voltage Supply Terminal 15 (B+) Relay J329 Evaporative Emission (EVAP) Canister Purge Regulator Valve N80 Fuel Pressure Regulator Valve N276 Intake Door Motor V157 Camshaft Adjustment Valve 1 N205 Wastegate Bypass Regulator Valve N75 Turbocharger Recirculating Valve N249 Oxygen Sensor (O2S) Heater Z19 Oxygen Sensor (O2S) Heater 1 [behind Three Way Catalytic Converter (TWC)] Z29 Coolant Circulation Pump Relay J151 After-Run Coolant Pump V51 Coolant Fan Control (FC) Control Module J293S891403_89Fuel Pump Control Module J53849Engines1.9L/105 HP TDI Engine with 2-Valve TechnologySpecial Features: • Switchable EGR cooler • • Crankshaft sealing flange with integrated engine speed sender wheel Accelerator pedal module with contactless accelerator pedal position senders Contactless clutch pedal switch•S318_033Technical DataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Max. output Max. torque Engine management Fuel Exhaust gas treatment TBD 4-cylinder in-line engine 116 cu. in. (1896cc) 3.1 in. (79.5mm) 3.6 in. (95.5mm) 2 19:1 105 HP (77 kW) at 4,000 rpm 184 ft. lb. (250 Nm) at 1,900 rpm Bosch EDC 16 Diesel, min. 49 CN Exhaust gas recirculation and oxidizing catalytic converterTorque and Power295 136Torque (Ft. Lbs.)177 118 5982 54 271000 2000 3000 4000 Engine Speed [rpm] S318_197S891403_7050Horsepower236109EnginesPedal AssemblyThe pedal assembly includes accelerator, brake and clutch control modules. The brake pedal module housing is made of aluminium and sheet steel. The accelerator pedal and the clutch pedal module housings are made of plastic. Pedal position sensors recognize the pedal position without making direct contact with pedal sensing components.Brake Pedal Module Clutch Pedal Module Accelerator Pedal ModuleS318_038Clutch Position Sensor G476 The Clutch Position Sensor G476 is a Hall effect device that signals the engine control module that the clutch pedal has moved. This deactivates the cruise control system and briefly reduces fuel to the fuel injectors to prevent engine shudder during the resulting gear change. For additional information on the accelerator, brake and clutch pedal assembly please refer to SSP 861403 “The new Jetta Steering and Suspension” .Clutch Pedal Master CylinderAccelerator Pedal Position Sensors G79 and G185 The Accelerator Pedal Position Sensors G79 and G185 are located in the accelerator pedal module. Both are inductive sensors that provide the exact position of the accelerator pedal to the engine control module. The engine control module uses this information to control the amount of fuel available to the fuel injectors.Position Sensors G79 and G185Accelerator Pedal Metal PlateS318_054 Clutch Position Sensor G476 S318_06451Automatic Transmission6-Speed Direct Shift Gearbox (DSG) 02EThe 02E 6-speed gearbox combines the advantages of a manual transmission with those of an automatic transmission: Manual: • High efficiency • • • Rugged design Sporty performance Comfort and convenience when changing gears • 02E DSG features include: • Six forward gears and one reverse gear • • Normal shift control program “D” and Sport shift control program “S” Tiptronic shift control and steering wheel shift control Mechatronics: electronic and hydraulic control modules in a single unit are integral to the transmission Oil cooler and compressed air filter are mounted on the transmission Maximum torque 258 ft. lbs. (349 Nm) For additional information on the DSG, please refer to SSP 841403 “Volkswagen 02E Direct Shift Gearbox” .Automatic: • •The 02E meets the high standards of comfort expected by automatic transmission users by using two multi-plate clutches and several automatic shift programs. The 02E also provides pure driving enjoyment for manual transmission users by allowing the driver to control the gear selection and shifts with its quick, smooth gearshifts. The 02E also provides better fuel economy than typical manual transmissions.Compressed Air Filter Oil CoolerMechatronics Control Modules Multi-Plate Clutches S318_00252Automatic Transmission6-Speed Automatic Transmission 09GThe 6-speed automatic transmission 09G is transverse mounted, compact, lightweight and electronically controlled. Features of the 09G include: • Maximum torque 229 ft. lbs (310 Nm). • • • • Weight 185 lbs. (84kg) Length 13.8 in. (350mm) Torque converter with lockup Automatic and Tiptronic operationS318_024Forward and reverse gears have simple planetary gear sets with a double Ravigneaux planetary gear set. Modulating valves are activated by the transmission control module to control pressure build-up in the multi-plate clutches and plate brakes. By allowing a delayed pressure build-up the modulating valves deliver fast response times and smooth shifts.For additional information on this transmission, please refer to SSP 851503 “The 6-Speed Automatic Transmission 09G” .53SuspensionSuspension FeaturesThe suspension of the new Jetta sets the standard in its class. An optimized front axle strut suspension provides state of the art handling characteristics. The new balanced four-link rear axle suspension complements the front suspension with its own superior performance characteristics. Electro-mechanical power steering provides excellent handling assistance while maintaining road feel. This variable assist system also automatically adjusts the level of assist depending on vehicle speed.•Floor mounted accelerator pedal assembly with redundant position sensors•Optimized McPherson strut suspension•Direct 1 to 1 anti-roll bar connection•Electro-mechanical power steering•Dual rate brake servo•Teves MK 60 Electronic stabilization system54SuspensionFor additional information on the suspension, please refer to SSP 861403, “The new Jetta Steering and Suspension” .•Four-link rear suspension • Tire pressure monitoring system (delayed introduction)•Power brakes•Toe and camber adjustments on rear suspensionS891403_2755Electrical SystemFuse and Relay LocationsMounting Locations The electrical system on the new Jetta is entirely redesigned. Because the electrical system has been completely reconfigured, the mounting location of fuse and relay centers have changed. The adjacent diagram shows the various fitting locations. For additional information on the electrical system, please refer to SSP 873403, “The new Jetta Electrical System Design and Function” .Fuse and relay center under the hood on the driversideBack-up fuse box under the hood on the driversideFuse box behind the instrument cluster on the driverside56Electrical SystemRelay carrier below the instrument cluster on the driverside, above the power supply control moduleRelay carrier inside the power supply control module, below the instrument cluster on the driversideS891403_6157Electrical SystemCAN Networking ConceptNetworked Control Modules To allow the new Jetta’s control modules to communicate, they are connected by various data bus systems. The Data Bus On Board Diagnostic Interface J533 provides access to the following data bus systems: • Drivetrain CAN-bus • • • • Convenience CAN-bus Infotainment CAN-bus Instrument cluster CAN-bus Diagnosis CAN-bus In addition to the CAN-bus, a number of electric components are networked via the LIN data bus. Refer to SSP 873403, “The new Jetta Electrical System Design and Function” for detailed information on CAN-bus communications.Key D E221 G85 G397 H8 J104 J136 Ignition/Starter Switch Control Module in Steering Wheel Steering Angle Sensor Rain/Light Recognition Sensor Alarm Horn ABS Control Module Memory Seat/Steering Column Adjustment Control Module J217 Transmission Control Module (TCM) J220 Motronic Engine Control Module J234 Airbag Control Module J255 Climatronic Control Module J285 Instrument Cluster Control Module J334 Anti-Theft Engine Disable Control Module J364 Auxiliary Heater Control Module J386 Driver's Door Control Module J387 Front Passenger's Door Control Module J388 Left Rear Door Control Module J389 Right Rear Door Control Module J393 Comfort System Central Control Module J400 Wiper Motor Control Module J431 Headlamp Range Control Module J446 Parking Aid Control Module J500 Power Steering Control Module J503 Radio/Navigation Display Control Module J519 Vehicle Electrical System Control Module J525 Digital Sound System Control Module J527 Steering Column Electronic Systems Control Module J533 Data Bus On Board Diagnostic Interface J587 Selector Lever Sensor System Control Module* J604 Auxiliary Air Heater Control Module J743* Direct Shift Gearbox (DSG) Mechatronic R Radio T16 16-Pin Connector *On direct shift gearboxes only58Electrical System16-Pin Connector T16Engine Control Module J220DSG Mechatronics J743Transmission CM J217ABS CM J104Headlamp Range CM J431Selector Lever CM J587Power Steering CM J500Airbag CM J234 Steering Angle Sensor G85 Data Bus On Board Diagnostic Interface J533 Steering Wheel CM E221 Ignition/Starter Switch D Instrument Cluster CM J285 Anti-Theft Engine Disable (Immobilizer IV) CM J334 Parking Aid CM J446 Steering Column Electronic Systems CM J527Navigation CM J503/ Radio RSAT RadioVehicle Electrical CM J519 Digital Sound System CM J525 Memory Seat/ Steering CM J136 Rain/Light Recognition Sensor G397Wiper Motor CM J400Climatronic CM J255 Auxiliary Heater CM J364*Auxiliary Air Heater CM J604*Drivetrain CAN-busConvenience CAN-busDriver's Door CM J386Left Rear Door CM J388Infotainment CAN-busLIN BusFront Passenger Door CM J387Right Rear Door CM J389Comfort System Central CM J393Instrument Cluster CAN-busDiagnosis CAN-busAlarm Horn H8 * May not be available on North American market vehiclesCAN-bus Wire Communications Line59Electrical SystemAir Conditioning SystemsDual Zone Climatronic The new Jetta is equipped with a dual zone air conditioning system. The temperature on the driver's and front passenger's sides can be controlled separately to between 60°F (16°C) and 85°F (29.5°C). Pressing the “Auto” button for longer than two seconds allows the temperatures on both sides to be synchronized to the driver's side. Two air-conditioning zones are achieved by using two temperature doors within the air conditioner. All air conditioner doors on the Dual Zone Climatronic are actuated by six control motors with integrated potentiometers. The Dual Zone Climatronic can be operated either automatically or manually. To prevent fogging of the windshield, the Dual Zone Climatronic automatically increases air flow to the windshield if the compressor is off and the windshield wipers are on. The defrost door is also opened wider. The Dual Zone Climatronic also reduces the fresh air blower speed depending on vehicle speed. This minimizes the airflow noise of the air conditioner. The fresh air blower is automatically adjusted as a function of road speed. This adjustment in blower speed is not noticeable by the vehicle occupants.S891403_5660Electrical SystemClimatic System The Climatic system manages the interior of the vehicle as one climate zone. The Climatic air conditioner has a combined fresh air/recirculating door that, like the temperature control door, is driven by a control motor. The Climatic system uses a flexible shaft to control the position of the air distribution doors. Temperature requests are relayed to the control module by a potentiometer in the rotary switch. The requested temperature setting is achieved by adjusting the position of the temperature door. Interface with the Air Conditioner The various components of the Climatic system and the heating system are divided into two units: an electronic front unit and a mechanical rear unit that is controlled by a flexible shaft. The heater is controlled by a bowden cable. The air conditioner is serviced similarly to other vehicles.S891403_5761Heating and Air ConditioningIntroductionThe new Jetta’s heating, ventilation and air conditioning systems (HVAC) is available in two versions, depending on the option selected. • The Dual Zone Climatronic heating and air conditioning system • The Climatic heating and air conditioning system All operating controls for the system are located on the control panel. Feedback LEDs on all buttons provide an indication of active functions. The Dual Zone Climatronic and Climatic systems include an interior temperature sensor.Dual Zone Climatronic SystemDriver Seat Heating Control Front Passenger Seat Heating ControlLED IndicatorsS891403_63 Interior Temperature Sensor62Heating and Air ConditioningClimatic System The “AC” button on the Climatic system is labelled “ECON. ” Air conditioning is deactivated by pressing the “ECON” button.Interior Temperature SensorFeedback LEDS891403_64 “AC” is renamed “ECON” .Floating Mount Installation To ensure a uniform fit, the system control units are installed using floating mounts. This installation method allows perfect alignment with the trim panel when the panel is installed.S318_079 Floating Mounts63Heating and Air ConditioningFunctions of the Systems in OverviewComponents Pollen filter with activated charcoal Air recirculation control Air flow control Temperature control Central footwell control Defrost control Left Vent Temperature Sensor G150 Right Vent Temperature Sensor G151 Left Footwell Vent Temperature Sensor G261 Right Footwell Vent Temperature Sensor G262 Fresh Air Intake Duct Temperature Sensor G89 Evaporator Vent Temperature Sensor G263 High Pressure Sensor G65 Fresh Air Blower V2 Sunlight Photosensor 2 G134 Interior temperature sensor Air recirculation mode Dual Zone Climatronic Yes Yes Yes Two doors actuated by control motors Actuated by control motor Actuated by control motor Left and right Climatic Yes Yes No One door actuated by a control motor Actuated by flexible shaft Actuated by flexible shaft LeftLeft and right Yes Yes Yes With electronic control Yes YesLeft No Yes Yes With series resistor No YesBy pressing the air recirculation button When driving in reverse In wipe-wash modeS891403_2864Heating and Air ConditioningAir Distribution SystemThe air distribution system on the new Jetta is similar to the systems on previous Jettas. However, significant improvements to the system have been made, including: • The cross sectional area of all air ducts has been increased. • The air duct to the defrost and instrument panel vents runs through the instrument panel. The front side windows are now ventilated through new vents in the A-pillar. • The rear passenger area is vented by a single air duct leading to the left and right footwells. The Dual Zone Climatronic air ducts in the instrument panel provide indirect ventilation through vents in the top of the instrument panel.•Indirect Ventilation in the Instrument PanelVents in the A-PillarS318_191 Door Controlled Center Rear FootWell Vent Rear Left Footwell Vent Rear Right Footwell Vent S318_020A center console vent is available that directs airflow to the center rear vents through a common air duct.Air Conditioning SystemDummy CoverRear FootWell Vent DuctS318_18165Heating and Air ConditioningThe main difference between the Climatronic and Climatic systems is the method used to control air distribution. The Dual Zone Climatronic system has an additional fresh air door, which closes at speeds above 60 mph (97 kph). This provides constant fresh air flow at different vehicle speeds.The figure below shows the air conditioner of the Dual Zone Climatronic system. The heating/ventilation system and Climatic system use a fresh recirculation door. The Dual Zone Climatronic uses a fresh flow door and a separate air recirculation door.Air Flow Door Motor V71 Defrost Door Central Door (Instrument Panel), Left FootWell Vent Footwell Doors Not Visible Temperature Sensor G261 Fresh Air/Air Flow Door Fresh Air Intake Duct Temperature Sensor G89Defroster Door Motor V107Recirculated Air Door Fresh/Recirculating Air Door Motor V154 Right FootWell, Vent Temperature Sensor, G262 Right Temperature Door Motor V159 Evaporator Vent Temperature Sensor G263 Right Rear Footwell VentLeft Temperature Door Motor V158Central Air Door Motor V70 (Instrument Panel/ Footwell) Temperature Doors, Left and Right Left Rear Footwell VentS318_131 Rear Center Vent (center console only)66Heating and Air ConditioningStorage Box Cooling All vehicles are equipped with a cooled glovebox storage compartment located in the front passenger side area. The storage compartment is cooled directly by air from the evaporator. The cooling level is adjusted manually by turning an adjustable nozzle. The center console also has an adjustable vent for temperature control. Cooled air is directed from the center console air duct to the storage compartment. This cooled air supply can also be adjusted manually by turning an adjustable nozzle.S318_004Adjustable Vent S318_006 Adjustable VentS318_14367Heating and Air ConditioningOverview of the Dual Zone Climatronic/Climatic SystemFresh Air Intake Duct Temperature Sensor G89* Left Footwell Vent Temperature Sensor G261 Right Footwell Vent Temperature Sensor G262* Left Vent Temperature Sensor G150 Right Vent Temperature Sensor G151* High Pressure Sensor G65Evaporator Vent Temperature Sensor G263 Sunlight Photosensor 2 G134* Defroster Door Control Motor Position Sensor G135* Recirculation Door Motor Position Sensor G143 Central Door Motor Position Sensor G112* Back Pressure Door Motor Position Sensor G113* Left Temperature Door Potentiometer/ Actuator G220 Right Temperature Door Potentiometer/ Actuator G221*Instrument Cluster Control Module 285 Climatronic Control Module J255Instrument Cluster CAN-busMotronic Engine Control Module J220Drivetrain CAN-bus S891403_5868Heating and Air ConditioningDefrost Door Motor V107* Fresh/Recirculating Air Door Motor V154 Left Temperature Door Motor V158 Right Temperature Door Motor V159* Central Air Door Motor V70*Air Flow Door Motor V71* A/C Compressor Regulator Valve N280 Fresh Air Blower V2 with integrated fresh air blower controller. (In the Climatic system, air flow is not controlled electronically, but through series resistors.)Steering Column Electronic Systems Control Module J527Auxiliary Air Heater Control Module J604 Convenience CAN-bus Vehicle Electrical System Control Module J519Infotainment CAN-bus Data Bus On Board Diagnostics Interface J533 S318_083* Only in combination with Dual Zone Climatronic69Heating and Air ConditioningFunction Diagram - Air Conditioning SystemsInput Signal Output Signal Positive Ground CAN-busG89*G261G262*G263G150G151*G134*J255V70*G112*V71*G113*V107*G135*S318_115Heated Driver Seat Control Module J131 Heated Front Passenger Seat Control Module J132G89 G261 G262 G263 G150 G151 G134Fresh Air Intake Duct Temperature Sensor Left Footwell Vent Temperature Sensor Right Footwell Vent Temperature Sensor Evaporator Vent Temperature Sensor Left Vent Temperature Sensor Right Vent Temperature Sensor Sunlight Photosensor 2J255 V70 G112 V71 G113 V107 G135Climatronic Control Module Central Air Door Motor Central Door Motor Position Sensor Air Flow Door Motor Back Pressure Door Motor Position Sensor Defroster Door Motor Defroster Door Motor Position Sensor70Heating and Air ConditioningTerm. 75 Term. 30 Term. 15 Term. 31 J533Convenience CAN-busN280V2**G65Unventilated Interior Temperature SensorV154G143V158G220V159*G221* S318_117* Used with Dual Zone Climatronic system only ** The V2 Fresh Air Blower motor used with Dual Zone Climatronic only. Climatic and the heater are controlled by series resistors.The Climatic sensors and actuators use different designations. For additional information, please refer to current service repair information.V158 G220 V159 G221 Left Temperature Door Motor Left Temperature Door Potentiometer/ Actuator Right Temperature Door Motor Right Temperature Door Potentiometer/ ActuatorN280 G65 V2 J533 V154 G143A/C Compressor Regulator Valve High Pressure Sensor Fresh Air Blower Data Bus On Board Diagnostic Interface Fresh/Recirculating Air Door Motor Recirculation Door Control Motor Position Sensor71Heating and Air ConditioningSensorsInterior Temperature Sensor Function The interior temperature sensor replaces the Instrument Panel Interior Temperature Sensor G56 with ventilation motor. It is an integral part of the control unit. The new sensor measures: • Surface temperature • • Unit temperature Sunlight penetration Its advantages over the previous sensor include: • The sensor housing is protected, making it less susceptible to obstructions that could interfere with temperature regulation • • No moving parts to wear and fail No openings in the trim provide a design advantageNTC Element and PhotodiodeS318_237S318_141 Signal Line to the Control Unit72Heating and Air ConditioningConstruction The interior temperature sensor is not vented and consists of an integrated thermo-optical sensor, an NTC element in combination with a photodiode. The NTC element measures the temperature and intensity of solar radiation on its surface. This allows the sensor to measure the air temperature in the vehicle’s interior even if the sensor's surface is heated. The sensor signals are transmitted to the Climatic or Dual Zone Climatronic. Software then evaluates the sensor signals and regulates the temperature of the vehicle’s interior. For additional information please refer to the following: SSP 881203 “HVAC Theory and Operation” SSP 894303 “The Phaeton Heating and Air Conditioning System” SSP 899303 “The Touareg Heating/Air Conditioning System”73Heating and Air ConditioningActuatorsFresh Air Blower and Integrated Fresh Air Blower Controller V2 The Dual Zone Climatronic system has a fresh air blower with an integrated controller. The fresh air blower is accessible from the front passenger footwell. Fresh Air Blower Controller Activation The Fresh Air Blower V2 with integrated electronic fresh air blower controller is controlled by the air conditioner control module via a pulse-width modulated signal (PWM) and can also send back a diagnostic feedback signal. A single pulse transmitted in the diagnostic feedback signal indicates “no fault” to the air conditioner control module. However, two pulses indicate that the current is limited; three pulses indicate that the temperature is too high and may cause the fresh air blower to slow or shutdown.Electronics Housing CoverFresh Air Blower RotorS318_195Climatronic Control Module J255Diagnosis S318_123PWM Term. 30 Term. 31Fresh Air Blower V2One Pulse Two Pulses Three Pulses ti tp S318_165 ti = time segment of one pulse tp = time segment of one period74Radio and NavigationRadio and Navigation SystemsRCD 300 Radio System (Base Radio) The RCD 300 radio is a standard radio system. It has the following features: • Two or four loudspeaker channels (each 20 W) • • • • • • • • • • RDS FM/AM Display of stored stations and RDS names MP3 compatible FM-2 tuner Control by multi-function steering wheel (MFS) and multi-function display (MFD) Integrated single CD drive Controls for external 6 disc CD changer Telephone control (hands-free operation) Self-diagnosis including speaker diagnosis Transport Mode • • • • • • RCD 500 Radio System (Premium 7) The premium radio in the new Jetta is the RCD 500 with the following features: • Four loudspeaker channels (each 20 W) • • • • • • • RDS FM/AM Display of stored stations and RDS names MP3 compatible FM-2 tuner Control by multi-function steering wheel (MFS) and multi-function display (MFD) Integrated 6 disc CD changer Controls for additional 6 disc CD changer Telephone control (hands-free operation) SAT Optional Satellite Radio Sound adaptation capabilities Self-diagnosis including speaker diagnosis Transport Mode Add-on amplifier capabilityS891403_121S891403_12075Radio and NavigationMFD 2 Radio DVD Navigation System (Delayed Introduction) The MFD 2 radio DVD navigation system operates similarly to the radio navigation system in the Touareg. Features include: • Multi-color display (MCD) • • • • • • • Dynamic traffic guidance Four loudspeaker channels (each 20 W) RDS FM/AM Display of stored stations together with RDS names Control by multi-function steering wheel (MFS) and multi-function display (MFD) Controls for additional 6 disc CD changer Self-diagnosis including speaker diagnosis To remove and install a radio, remove the cover to access the mounting screws.S891403_4176ServiceSpecial ToolsAlignment bracket set VAS 6240 and supplementary set VAS 6240/2 are required service tools for new Jetta frame and chassis alignment and straightening. New required equipment: • Alignment bracket set VAS 6240 • • Supplementary set VAS 6240/2 Portal gauge supplement VAS 5007/18Straightening Bracket Set VAS 6240S318_052 S318_26777ServiceNew Special ToolsTool Number T10237 Diagram Application Door setting toolS318_269 T10236 Rear door removal toolS318_265 T10238 (1) T10240 (2) (1) (2) Accelerator pedal module release tool (1) Left-hand drive (2) Right-hand driveS318_291 V.A.G. 1598 (1) V.A.G. 1598/47 (2) (1) S318_293 (2) Dual Zone Climatronic, Climatic and heating and ventilation systems troubleshooting tools (1) Test box (2) Test adaptersS318_295S891403_2978Notes79Knowledge AssessmentAn on-line Knowledge Assessment (exam) is available for this Self-Study Program. The Knowledge Assessment may or may not be required for Certification. You can find this Knowledge Assessment at:www.vwwebsource.comFrom the vwwebsource.com Homepage: – – – – Click on the Certification tab Type the course number in the Search box Click “Go!” and wait until the screen refreshes Click “Start” to begin the AssessmentFor Assistance, please call:Certification Program Headquarters 1 – 877 – CU4 – CERT (1 – 877 – 284 – 2378) (8:00 a.m. to 8:00 p.m. EST)Or, E-Mail:Comments@VWCertification.com80Volkswagen of America, Inc. 3800 Hamlin Road Auburn Hills, MI 48326 Printed in U.S.A. December, 2004