TECHNICAL DOCUMENTATION
SSP 921703 Audi 2,0 Liter Chain-driven TFSI Engine

This PDF is currently unavailable.
Read document text
Service TrainingAudi 2.0 Liter Chain-driven TFSI EngineSelf-Study Program 921703Audi of America, Inc. Service Training Printed in U.S.A. Printed 1/2008 Course Number 921703 ©2008 Audi of America, Inc. All rights reserved. All information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies, and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, Inc. Always check Technical Bulletins and the latest electronic repair literature for information that may supersede any information included in this booklet. Trademarks: All brand names and product names used in this manual are trade names, service marks, trademarks, or registered trademarks and are the property of their respective owners.Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . Engine Mechanicals . . . . . . . . . . . . . . . . . . . . Oil System . . . . . . . . . . . . . . . . . . . . . . . . . Crankcase Ventilation System . . . . . . . . . . . . . . Cooling System . . . . . . . . . . . . . . . . . . . . . . Air Intake System . . . . . . . . . . . . . . . . . . . . . Fuel System . . . . . . . . . . . . . . . . . . . . . . . . Exhaust System . . . . . . . . . . . . . . . . . . . . . .1 5 19 25 27 31 37 45Engine Management System . . . . . . . . . . . . . . . 47 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . Knowledge Assessment . . . . . . . . . . . . . . . . . 51 53The Self-Study Program teaches the design and function of new vehicle models, automotive components, and technologies. The Self-Study Program is not a Repair Manual! The values given are only intended as a guideline. Refer to the software version valid at the time of publication of the SSP. For maintenance and repair work, always refer to the current technical literature.ReferenceNoteIntroductionIntroductionTechnical DescriptionFour Cylinder, Four Valve, FSI Turbocharged Gasoline Engine Engine Block – Cast Iron Crankcase – Balancer Shafts in Crankcase – Forged Steel Crankshaft – Sump-Mounted Oil Pump — Chain-Driven by Crankshaft – Timing Gear Chain — Front End of Engine – Balancer - Chain-Driven at Front End of Engine Cylinder Head – 4-Valve Cylinder Head – 1 INA Intake Camshaft Adjuster Intake Manifold – Tumble Flap Fuel Supply – Demand Controlled on Low and High-pressure Ends – Multi-Port High-pressure Injector Engine Management – MED 17 Engine Control Module – Hot-Film Air Mass Flow with Integral Temperature Sensor – Throttle Valve with Contactless Sensor – Map-Controlled Ignition with Cylinder-Selective, Digital Knock Control – Single-Spark Ignition Coils Turbocharging – Integral Exhaust Turbocharger – Charge-Air Cooler – Boost Pressure Control with Overpressure – Electrical Wastegate Valve Exhaust – Single-Chamber Exhaust System with Close-Coupled Pre-Catalyst Combustion Process – Fuel Straight Injection384_003Introduction2.0L Chain-Driven TFSI EngineTorque/Power Curve265 (360) 201 (150)Power in hp (kW) Torque in lb ft (Nm)243 (330) 220 (300) 200 (270) 177 (240) 121 (90) 155 (210) 133 (180) 110 (150) 88 (120) 67 (90) 40 (30) 44 (60) 22 (30) 0 0 1000 2000 3000 4000 5000 6000 7000 0 80 (60) 161 (120)Engine speed in RPMSpecifications Engine Code Type of Engine Displacement Maximum Power Maximum Torque Number of Valves Per Cylinder Bore Stroke Compression Ratio Firing Order Engine Weight Engine Management Fuel Grade Exhaust Emission Standard CCTA - CBFA Inline 4-Cylinder FSI Engine 121 cu in (1984 cm3) 200 hp (147 kW) at 5100 - 6000 rpm 206 lb ft (280 Nm) at 1700 - 5000 rpm 4 3.2 in (82.5 mm) 3.7 in (92.8 mm) 9.6 : 1 1-3-4-2 317 lb (144 kg) Bosch MED 17.5 95/91 RON ULEV (CCTA) - SULEV (CBFA)NotesEngine MechanicalsCylinder BlockThe cylinder block has a closed-deck configuration and is made of cast iron. It houses the five-bearing crankshaft assembly and the two balancer shafts. The housing for mounting the chain drives is integrated in the block. The cylinder liners are finished in a threestage fluid jet honing process. The undersides of the pistons are cooled by engine oil supplied by spray jets mounted on the cylinder block. The cylinder block is sealed on the transmission side by a sealing flange and gasket.384_004Engine MechanicalsOil PanThe oil pan consists of two sections. The upper section is made of an aluminum alloy (AlSi12Cu) and reinforces the crankcase through a bedplate effect. It also houses the oil pump. The upper section is bolted to the crankcase and sealed with a liquid sealant. The bottom section is made of sheet steel (deep drawn, punched, and catalytically coated). It houses Oil Level Sensor G12 and the drain plug. The bottom section is bolted to the upper section and sealed with a liquid sealant. The oil pan has an integral honeycomb insert made of polyamide to prevent oil churning when the vehicle is driven aggressively.Aluminum Alloy Oil Pan Top SectionPolyamide Honeycomb InsertStamped Steel Oil Pan Bottom Section384_006Engine MechanicalsCrankshaftThe five main bearing crankshaft is made of forged steel and induction hardened. Optimal balancing is achieved by using eight counterweights. To additionally reinforce the crankshaft assembly, the three inner main bearing covers are cross-bolted to the cylinder block. Trapezoidal Connecting Rod (Small End) Material: 36MnVS4 Length: 5.82 in (148 mm) Big-End Bearing: 1.88 in (47.8 mm) Small-End Bearing: 0.82 in (21 mm) The crankshaft main bearings are a two component type. Axial play of the crankshaft is controlled by thrust washers at the middle support bearing. Bronze bushings are press-fit into the small trapezoidal upper end of the connecting rods.Pistons Wrist PinThe lower end of the connecting rods are cracked to ensure a precision fit and reduce movement of the bearing cap under load. The upper and lower bearing shells of the connecting rod are not identical in composition. The upper bearing shell is a two-component composite bearing while the lower shell is a three-component composite bearing.Wrist Pin Retaining ClipBronze Connecting Rod BushingTrapezoidal Shaped Small End of Connecting RodConnecting Rod Upper Bearing ShellMain Bearing Cap Connecting Rod CapCross-Bolted Main Bearing Caps and Bolts384_007Engine MechanicalsThe chain drive sprocket is mounted to the crankshaft face and driven by a spur gear forged in the crankshaft. The other end of the chain sprocket also has a spur gear surface which drives the vibration damper. This method of joining allows high torque to be transmitted to the chain sprocket and vibration damper while keeping the diameter of the components small. This allows better sealing by the radial shaft seal at the vibration damper hub.On the transmission side of the engine, a dual mass flywheel or torque converter (depending on transmission) is mounted to the crankshaft with eight bolts.Vibration Damper Center Bolt Chain Sprocket384_009Spur Gear Drive for Chain SprocketPistonsThe pistons are specially designed for the FSI engine with a cast-in ring land for the upper piston ring. Coated skirts are used to help reduce frictional losses. The upper piston ring is rectangular, the second piston ring is a taper-faced ring, and the oil scraper ring is a bevelled ring with expander. The 31CrMoV wrist pins are held in place by snap rings. The bottom side of the pistons are cooled by engine oil from spray jets mounted on the cylinder block.Piston Ring Land384_051Engine MechanicalsCylinder HeadMLKNO JPIH Q R F E GD CS BT A384_010Engine MechanicalsThe 4-valve cylinder head is cast from aluminum alloy. Intake and exhaust valves are actuated by roller cam followers supported by hydraulic valve lifters. The intake and exhaust camshafts are chain-driven. The variable timing of the intake camshaft is accomplished through the INA camshaft adjustment system (page 10).The cylinder head cover adds support by acting as a ladder frame and does not have to be disassembled to remove the cylinder head. The diagonal opening and sealing face simplifies drive chain installation.Features– Crossflow Cylinder Head Made of ASi10Mg(Cu)wa. – Three-Layer Metal Head Gasket. – Intake Ports Divided by Baffle Plate. – Cylinder Head Cover Made of AlSi9Cu3 with Integrated Ladder Frame, Bolted to Cylinder Head and Sealed with Liquid Sealant. – Intake Valve: Solid-Stem Valve, Chrome-Plated with Reinforced Seat. – Exhaust Valve: Sodium Filled Hollow-Stem Valve, Chrome-Plated and Tempered with Reinforced Seat. – Single Valve Spring Made of Steel. – Roller Cam Followers Running in Needle Bearings, Hydraulic Valve Clearance Adjustment. – Hydro-Formed, Assembled Intake Camshaft with Variable Valve Timing, Dwell Angle 190°, Valve Lift 10.7 mm. – Hydro-formed, Assembled Exhaust Camshaft with Press-Fitted Drive Gear, Dwell Angle 180°, Valve Lift 8 mm. – INA Camshaft Adjuster, Timing Range 60° Crank Angle, Basic Position is Locked in “Retard” (engine not running).Legend A B C D E F G H I J Check Valve Sealing End Cap Exhaust Valve Intake Valve Valve Stem Seal Valve Spring Valve Spring Retainer Valve Keeper Exhaust Camshaft Intake Camshaft with INA Adjuster K L M N O P Q R S T Cylinder Head Cover Cylinder Head Cover Screw Screw Plug Sealing End Cap Hydraulic Valve Clearance Adjuster Roller Cam Follower Dowel Pin Cylinder Head Bolt with Washer Exhaust Manifold Locating Pin Exhaust Manifold Stud10Engine MechanicalsBearing BridgeA die-cast aluminum bearing bridge mounted at the front of the cylinder head has the following tasks: – Supporting the Camshafts. – Supplying Pressurized Oil to Camshaft Bearings. – Supplying Pressurized Oil to Camshaft Adjuster. – Controlling Axial Movement of Camshafts. – Mounting Point for Camshaft Adjustment Valve 1 N205. The bearing bridge also serves to connect the two oil galleries of the cylinder head. A check valve and filter screen are integrated in the pressurized oil duct to the INA camshaft adjuster.384_011Die-Cast Aluminum Bearing Bridge11Engine MechanicalsINA Camshaft Adjustment SystemThe 2.0L chain drive engine uses a hydraulic vane cell adjuster on the intake camshaft to affect valve timing. Only the intake camshaft has variably adjusted timing on this engine. Oil pressure for this task is provided by the engine oil pump. The variable camshaft adjuster provides an adjustment range of 60° crank angle. The camshaft is locked in the retard position at engine shut-off. This function is performed by a spring-loaded locking pin. The camshaft is released when the engine oil pressure exceeds 7.25 psi (0.5 bar). The rotor of the vane cell adjuster is welded to the intake camshaft. The 4/3-way central valve required for adjuster control is integrated in the camshaft. Intake camshaft timing is map-controlled by the engine control module. The goals are to improve engine power, enhance running smoothness, and reduce emissions (through internal exhaust gas recirculation).Function Pressurized oil flows to the central valve via the camshaft bearing through bores in the camshaft. From here, depending on adjustment requirements, the oil flows through additional bores in the camshaft to one of the chambers in the adjuster. The valve is activated electrically via Camshaft Adjustment Valve 1 N205. When activated by a PWM signal, the solenoid produces a variable magnetic field. Depending on the strength of the magnetic field, the shaft with ball is shifted towards the camshaft axis of rotation. This, in turn, displaces the 4/3-way central valve and allows the oil to flow to the corresponding chamber. The new design has many advantages. It provides a very high adjustment rate capability even in unfavorable conditions such as cold starts or high oil temperatures during engine idling.Cover 4/3-Way Central Valve Low-Friction BearingStatorVane with SpringLocking PinArmatureLocking SpringShaft with BallRotor (Welded to Camshaft)Camshaft Adjustment Valve 1 N205 Winding Coil Element Camshaft with Bores for Hydraulic Control384_01212Engine MechanicalsChain DriveIntake Camshaft with INA Adjuster384_015Balance Shaft Drive GearOil Pump DriveAll three chains of the 2.0L engine are driven directly by the chain sprocket mounted to the crankshaft. The chains are arranged in three planes (levels). – 1st Plane - Balancer Shaft Drive – 2nd Plane - Camshaft Drive – 3rd Plane - Oil Pump Drive Gear chains (as opposed to roller chains) are used in all three planes. They are 1/4 inch gear chains whose tension is controlled by four tension plates and five guide plates.Gear chains are highly flexible in application because their width can be adapted for any power requirement by selecting the number of plates accordingly. They have an efficiency of approximately 99%.Advantage of Gear ChainsGear chains are more wear resistant and produce less noise than roller chains. The amount of space required for a given power transmission capacity is less than that of a timing belt or roller chain.13NoteBlue outer plates are attached to each chain at defined intervals. They serve as an aid for setting valve timing.Engine Mechanicals1st Plane - Balance Shaft DriveBalance ShaftsGuide Rail384_016Hydraulic Chain Tensioner Idler GearTensioning RailSlide RailChain SprocketTwo cylinder block housed balance shafts are used to counteract unwanted vibration at engine speeds above 4000 rpm from being transmitted to the car body. The balance shafts run at twice the engine speed in opposite direction from one another. The direction of the second shaft is reversed by an idler gear. The horizontally staggered arrangement of the balance shafts also helps reduce vibration. The balance shafts are made from spheroidal graphite cast iron and run in three bearings.Chain lubrication is provided by oil returning from the cylinder head. Oil is collected and distributed to the chain by a separate lubrication channel. Mounting the balance shafts in the cylinder block has the following advantages: – The Cylinder Block Provides Higher Rigidity. – Oil Foaming is Eliminated by Moving the Rotating Parts Away from the Oil Sump.14Engine MechanicalsBalance Shaft LayoutOil Return Channel from Cylinder HeadPlastic PipeOil Return Line384_017The oil return channel from the cylinder head is located on the exhaust side of the cylinder block. Return oil flows through the balance shaft housing.The balance shaft is mounted in a plastic pipe. This prevents oil returning from the cylinder head from churning and foaming from direct contact with the balance shaft.Helical Balance Shaft Drive Gear15Idler Gear384_019Engine Mechanicals2nd Plane - Timing GearSlide Rail, Timing GearChain Sprocket, Exhaust CamshaftCollar Bolt, Tensioning RailsChain Sprocket, INA Intake Camshaft AdjusterTensioning Rail, Timing Gear Balance Shaft Gear, Exhaust Side of EngineGuide Rail, Timing GearHydraulic Tensioner, Camshaft Chain Drive Balance Shaft Gear, Intake Side of EngineTensioning Rail Chain SprocketSlide RailBalance Shaft Chain TensionerCollar Bolt, Tensioning RailChain, Oil PumpTensioning Rail, Oil Pump384_020Chain Sprocket, Oil PumpThe camshafts are driven by chains on the second level. Tensioning is accomplished by a hydraulic tensioner. The tensioner can be accessed through a service opening. This allows the timing chain to be detached after removing the cylinder head without having to remove the engine timing cover.Chain Tensioner with Rig Pin384_04316Engine Mechanicals3rd Plane - Oil Pump DriveDrive Sprocket Attached to Crankshaft for Oil PumpSlide RailOil PumpOil Filter Screen Pressure Regulating Valve384_021The chain drive for the oil pump is located in the third plane. A polyamide slide rail is used in this drive to locate and tension the chain. The tension is produced by a mechanical spring. A hydraulically damped system is not needed due to the low dynamic load. The chain is lubricated by return oil or by the oil in the oil pan.Tensioning Spring384_02217Engine MechanicalsAlternator/AC Compressor DriveA subframe supports both the alternator and air conditioning compressor. They are driven by a poly-vee belt which is tensioned by a spring-loaded tensioner.SubframeAlternator384_023Spring-Loaded Belt Tensioner Air Conditioner Compressor18Oil SystemLubrication System SchematicLegend 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Screen Oil Pump, Chain-Driven Cold Start Valve Pressure Regulating Valve Check Valve, Integrated in Oil Pump Water-Oil Heat Exchanger Check Valve, Integrated in Oil Pump Oil Cleaner Oil Drain Valve Oil Pressure Switch F1 Spray Jets with Integrated Valves Oil Screen Chain Tensioner Chain Tensioner Gear Lubrication Coarse Oil Mist Separator Non-Return Valve, Integrated in Cylinder Head Oil Screen Flow Restrictor Lubrication of High-pressure Fuel Pump Cam Fine Oil Mist Separator Oil Screen Check Valve, Integrated in Bearing Bridge Multi-Directional Regulating Valve for Camshaft Adjuster Camshaft Adjustment Valve 1 N205 Oil Level Thermal Sensor G266 Vacuum Pump TurbochargerA2423 A 25 Bearing Bridge 22176 978 10Subframe 16 Oil Separator5152 4 26 3 1Oil Pan19Oil System21AAAAA2718 B B B B B B B B19Vacuum PumpBBBBBBBBA B C D E Camshaft Bearing Support Element Balance Shaft Bearing Connecting Rod Main BearingA 17AAACylinder Head131428Low-Pressure Circuit C D C D D C D High-Pressure Circuit1212EEEEE121111 121111CCCCylinder Crankcase3834_02420Oil SystemOil PumpThe external gear oil pump is housed in the oil pan top section and is chain-driven by the crankshaft. The oil pressure is controlled inside the pump by a control spring and piston. The system is also protected against overpressure by a spring loaded valve ball (cold start valve). Excessively high oil pressures can occur at high oil viscosity levels during cold starting.CoverDrive Shaft Housing Bushing Steel Ball Chain SprocketCompression SpringEnd CapPistonExternal Oil Pump GearsCompression Spring Stop384_02521Oil SystemOil Filter and CoolerThe oil filter and oil cooler bracket are integrated in a subframe. It also houses the oil pressure switch and the tensioner for the belt drive. The oil filter cartridge is accessible from above for easy servicing. To prevent oil spillage when changing the filter, a breech pin opens as the filter is removed. This allows the oil to flow back into the oil pan.View of Engine Flange384_060Oil FilterOil CoolerOil Filter Module Bracket384_02622Oil SystemOil Filter CartridgeOil CoolerOil Feed from Oil CoolerNon-Return Valve Oil Flow to Engine Breech PinOil SealsReturn Line to Oil Pan Closed in this PositionNon-Return Valve ClosedSleeve Integrated in Oil Filter Breech Pin Resetting Range Allowing Direct Return To Oil Pan384_02723Direct Return to Oil PanNotes24Crankcase Ventilation SystemSystem OverviewIn the 2.0L chain-driven TFSI engine, blow-by gases are vented from the cylinder block through the cylinder head cover. An oil separator is installed on the cylinder block just below the engine coolant pump assembly. A baffle plate in the oil pan upper section prevents engine oil from being drawn out of the block at the gas extraction point. In the primary oil separator, the blow-by gases flow through a labyrinth to separate coarse particles from the oil. The primary oil separator has two separation stages which work on the baffle-plate principle. The separated oil flows back along oil return lines into the oil pan. The blow-by gases continue to flow from the primary oil separator through a large cross-section pipe to the cylinder head cover. The large cross-section results in a low crankcase breather gas flow rate which prevents oil droplets from travelling along the side wall of the pipe. The pipe is encased in insulating material. This prevents the system from freezing when there is a high water content in the blow-by gas. This occurs in cold conditions and when the vehicle is used frequently for short-distance driving. A fine oil separator is integrated in the cylinder head cover. A single-stage cyclone separator with a parallel bypass valve filters out any residual ultra-fine oil particles. The separated oil flows into the cylinder head through a port in the cylinder head cover; from there, the oil is returned to the oil pan. To prevent intake of the engine oil under excessively high vacuum, a check valve is installed at the end of the oil return duct. This check valve is installed in the honeycomb insert in the oil pan. The blow-by gas flows along a duct integrated in the cylinder head cover to a two-stage pressure regulating valve. The pressure regulating valve prevents excessively high vacuum from developing within the cylinder block. The pressure regulating valve is installed in a housing together with two check valves. The check valves regulate blow-by gas flow depending on pressure conditions in the intake manifold. If a vacuum is present in the intake manifold (for example, at low engine speed) when the exhaust gas turbocharger is not producing boost pressure, the blowby gases are drawn directly into the intake manifold. If boost pressure is present, the blow-by gas is inducted on the intake side of the turbocharger.Pressure Regulating ValveACFCheck ValveBlow-By Inlet In TurbochargerBlow-By Inlet in Intake Manifold (for Low Intake Manifold Vacuum Conditions)Diagnosis ChannelCyclone PCV ValveBlow-By Line Primary Oil Separator Oil Return Pipe Blow-By from Cylinder Crankcase Enters Primary Oil Separator Here Oil Return Pipe25Check Valve384_057Crankcase Ventilation SystemPositive Crankcase VentilationThis system supplies the crankcase with fresh air to mix with blow-by gases. Fuel and water vapors in the blow-by gases are absorbed by the fresh air and then discharged through the crankcase ventilation system. Fresh air is drawn in from the intake air system downstream of the air filter and Mass Air Flow Sensor. A breather pipe is connected to the cylinder head cover via a check valve (PCV valve). The PCV valve ensures a continuous air supply and that unfiltered blow-by gases cannot be aspirated directly. The PCV valve is also designed to open under high pressure inside the crankcase. This precaution prevents damage to seals due to over-pressure.PCV Valve384_056Cutaway View of Crankcase Breather Valve ACoverCompression Spring Direction of Flow Housing O-RingSealing DiscRetainerSilicone Valve Disc, PerforatedA O-Ring384_035Direction of Flow A-B Opening Pressure Pressure Greater Than - 0.10 psi (-7 hPa)Direction of Flow B-A 1.4 ± 0.21 psi (100 ± 15 hPa)26Cooling SystemEngine Cooling SystemThe engine uses a cross-flow cooling system. Engine coolant first flows to the front of the engine from the coolant pump. The coolant is then distributed along ducts and circulates around the cylinders. After circulating through the cylinder head, the coolant is routed back to the radiator via the thermostat housing or recirculated through the coolant pump if the thermostat is closed. The heat exchanger and turbocharger are part of the engine cooling circuit. The engine oil cooler is connected directly to the cylinder block through its mounting subframe. After-Run Coolant Pump V51 protects the turbocharger bearings from overheating after engine shut-off. The pump is activated by the engine control module based on programmed characteristic maps.Heat ExchangerCoolant Expansion TankTurbochargerEngine Oil CoolerCoolant Outlet from Cylinder Head to Heat ExchangerCoolant Pipe Thermostat/ Coolant Pump ModuleAfter-Run Coolant Pump V51384_028RadiatorNoteVehicle coolant systems are dependent on model equipment installed. For vehicle specific information, please consult the relevant Repair Manual.27Cooling SystemCylinder HeadCylinder BlockEngine Oil CoolerCoolant Pump Drive384_029Thermostat Housing With Coolant Pump InletOutletLong and Short Cooling Circuits Controlled By Coolant Thermostat28Cooling SystemCoolant PumpThe coolant pump, temperature sensor, and coolant thermostat are integrated in a common housing made of duroplastic. This housing is attached to the cylinder block below the intake manifold. A drive gear at the end of the balance shaft drives the coolant pump via a toothed belt. The larger drive gear on the pump acts as a speed reducer. A fan wheel is attached to the coolant pump drive gear to cool the toothed belt. The coolant pump impeller is made of plastic and has a special vane contour which permits high engine speeds with low risk of pump cavitation. The thermostat begins to open at 203 degrees F (95 degrees C) and is fully open at 221 degrees F (105 degrees C).NoteThe tension of the coolant pump drive belt is defined by the installation position of the coolant pump and cannot be adjusted. In the event of coolant pump failure, the housing must also be replaced. The toothed belt drive gear of the coolant pump has a left-hand thread.Engine Coolant Temperature (ECT) Sensor G62Coolant Pump ImpellerHeating Return LineFan WheelCoolant ThermostatBalance ShaftOutletInletToothed Belt Drive Gear with Left-Hand Thread Bolt384_03029Notes30Air Intake SystemIntake Manifold ModuleLegend 1 2 3 4 5 Throttle Valve Control Module Intake Air Temperature (IAT) Sensor G42 Evaporative (EVAP) Emission Canister Purge Regulator Valve N80 Vacuum Motor for Intake Manifold Flap Changeover Fuel Port, High-pressure Pump 6 7 8 9 10 11 Fuel Port, High-pressure Fuel Rail Double Check Valve for Charcoal Canister System High-pressure Fuel Rail Fuel Pressure Sensor G247 Intake Manifold Flaps Intake Manifold Runner Position Sensor G33634215678384_055931Air Intake SystemThe body of the intake manifold module is made of polyamide and consists of two shells which are plasticwelded together. The intake manifold flaps are trough shaped. Through this shape and their arrangement in the intake port, the intake airflow is improved when the flaps are open. An improvement in tumble capacity is also achieved when closing the flaps. The intake manifold flaps are adjusted by a vacuum motor. The motor uses a two stage process.Feedback about the flap position is provided by Intake Manifold Runner Position Sensor G336. When the engine is not running, the intake manifold flaps are closed. Blow-by gases and vapor from the charcoal canister vent directly into the airflow downstream of the throttle valve assembly.11384_0331032Air Intake SystemAir SupplyVent Hose TurbochargerVacuum Line Air IntakeIntake Tube PCV Line Vacuum PumpCharcoal Cannister LineAir FilterIntake Manifold Runner Control (IMRC) Valve N316Intake ManifoldVent HoseOil Separator Pressure Regulating ValvePressure HoseCharge-Air Cooler384_03233Air Intake SystemEvaporative Emission SystemVenting of fuel vapors from the charcoal canister while the engine is running involves using two different paths. When boost pressure from the turbocharger is present, fuel vapors cannot directly flow into the intake manifold. In this case, the vapors are directed to the intake side of the turbocharger. When boost pressure is not present, the vapors are drawn in through the intake manifold downstream of the throttle body. A double check valve in the evaporative system accomplishes this task.Fuel TankInflow into Intake Manifold (Charge Pressure Present) Exhaust Gas TurbochargerIntake ManifoldCharcoal CanisterInflow into Intake Manifold (No Charge Pressure) Double Check ValveEvaporative (EVAP) Emission Canister Purge Regulator Valve N80Charge-Air Cooler384_03734Air Intake SystemVacuum SupplyThe required vacuum for the brake booster and other vacuum driven components of the engine is produced by a mechanically driven vacuum pump. The pump is a swivel vane pump driven by the exhaust camshaft and is installed behind the high-pressure fuel pump. The vacuum pump is capable of providing a sufficient vacuum for all vacuum components under any operating condition.To Brake Servo Check Valve with Integrated T-PieceFor this reason, it is not necessary to use an additional vacuum reservoir. The pump is rated to deliver a continuous absolute pressure of 0.73 psi (50 mbar). Oil for lubricating the pump and to enhance the sealing of the pump vanes is provided through a special port in the cylinder head.Vacuum Pump on the Exhaust Camshaft Mechanically DrivenIntake Manifold Runner Control (IMRC) Valve N316Vacuum Motor35384_059Air Intake SystemVacuum Pump384_064The vacuum pump consists of a rotor running in bearings and a moving vane made of plastic which divides the vacuum pump into two sections.The position of the vane is constantly changing due to the rotational movement of the rotor. As a result, the volume of one section increases while the volume of the other section decreases.Vane Intake EndAir Inflow from Vacuum System Induced Air VaneRotor Rotor Compressed Air384_062384_063Pressure EndAir Outflow to Cylinder Head (Shuttle Valve)Oilway36Fuel SystemFuel SystemThe fuel system is an advanced version of the system used on earlier TFSI engines. All parts which are in direct contact with fuel are designed in such a way that the engine can run on any available fuel grade. Special materials are used to ensure the fuel system meets all requirements relating to corrosion protection. The high-pressure system is supplied with fuel by a returnless, demand controlled pre-supply system. Fuel is delivered at a variable pressure between 50.7 psi (3.5 bar) and 87.1 psi (6.0 bar). No low pressure sensor is used in this system. The correct fuel pressure is determined by mapped settings of the engine control module and subsequently set by Fuel Pressure Regulator Valve N276.Fuel Pressure Sensor G247 RailHigh-Pressure Fuel PumpFuel Pressure Regulator Valve N276Fuel FilterTer. 31 PWM Signal From Engine Control Module Ter. 30 Fuel Tank384_038Fuel Pump (FP) Control Module J53837Fuel SystemFuel RailThe fuel delivery rate of the high-pressure pump has been reduced through the use of a four-lobe cam. A quicker pressure build-up is thus possible. This buildup benefits both cold start and hot start situations.Fuel Pressure Sensor G247The fuel pressure sensor is mounted in the fuel rail and is designed for measuring pressures up to 2900 psi (200 bar).NoteAlways carefully follow the repair manual instructions when replacing the high-pressure fuel pump. The pump can be destroyed if the actuating cam follower is not properly installed.Fuel HighPressure Pump Four Lobed CamFuel Pressure Regulating Valve N276Cam FollowerFrom Fuel TankRailCamshaftFuel Pressure Sensor G247384_038Fuel Injector38Fuel SystemHigh-Pressure PumpThe demand controlled high-pressure pump by Bosch is driven by a four lobed cam on the end of the intake camshaft. The pump piston is driven by the camshaft and a cam follower. This reduces friction as well as the chain forces. The results are smoother engine operation and higher fuel economy. The use of the four lobe cam has allowed a reduced piston stroke compared to earlier versions of the 2.0L TFSI engine. Due to the shorter stroke, the individual delivery rates are lower. This, in turn, results in reduced pressure fluctuations. The metering precision of the injectors is also improved, as there is now one feed stroke per injection. The advantage of this is improved oxygen sensor control and fuel efficiency. The high-pressure pump produces a maximum pressure of 2175.5 psi (150 bar). The fuel pressure requested by the engine control module is adjusted by Fuel Pressure Regulator Valve N276. The pressure is regulated between 725.1 psi (50 bar) and 2175.5 psi (150 bar) depending on engine requirements. The high-pressure pump now has its own pressure limiting valve. This valve opens at approximately 2900 psi (200 bar) and admits pressure into the pump chamber. Previously, pressure was discharged into the low-pressure circuit. Excessively high-pressures can build up in overrun or when the engine heat soaks after shut-off. The pressure pulsations in the low-pressure circuit are reduced by a damping element integrated in the pump.NoteAlways follow the repair manual cautions and warnings when opening the high-pressure fuel system lines. Serious injury can result if proper procedures are not observed.384_040High-Pressure RegulationFuel pressure and fuel quantity are regulated by Fuel Pressure Regulator Valve N276. The signal from Fuel Pressure Sensor G247 is used by the engine control module as a parameter. This sensor is located in the fuel rail. Power demand has been reduced significantly through a newly designed fuel pressure regulating valve and associated control concept. At the start of delivery, Fuel Pressure Regulating Valve N276 is activated only very briefly. The intake valve closes, fuel pressure builds up, and fuel delivery immediately begins. After the intake valve closes, electrical power to the solenoid valve is shut off. The intake valve kept closed by the pressure in the pump until the pump piston feed stroke is complete and the intake stroke begins.NoteApplying continuous voltage to Fuel Pressure Regulator Valve N276 for longer than one second will cause damage to N276.39Fuel SystemLow-Pressure DamperInlet ValveFuel Pressure Regulator Valve N276Delivery ChamberNeedleOutletFlangeCoil Armature Piston Seal O-Ring384_052Pressure Limiting Valve Fuel Pump (FP) Control Module J538Connection to Low PressureConnection to RailNoteThese cutaway views do not fully correspond to the originally installed pump.384_05340Fuel SystemControl ConceptThe diagram shows the high-pressure regulation function of the high-pressure pump. The complete delivery cycle for a cam is shown here. This cycle takes place four times during a single revolution of the camshaft. The bottom diagram shows the movement of the pump piston and the activation of Fuel Pressure Regulator N276.F Flow Force, EFP Flow Force, EFPFRV De-energizedF IV F SpringFRV De-energized F IVFIVDelivery ChamberFDelivery ChamberEVIntake StrokeIFRVFig. 1 – Pump Piston Intake Stroke, Fuel Flows into Pump Chamber. – N276 De-energizes. – Intake Valve (IV) Opens Because Spring Force is Less than Flow Force of Transfer Fuel Pump - Vacuum is Present Inside Pump.41Fig. 2 – Pump Piston Feed Stroke, Fuel Flows Back to Inlet. – N276 De-energizes. – IV Opens Due to Upward Motion of Pump Piston, Fuel Moves from Pump Chamber into Inlet. – EV Closes.– Exhaust Valve (EV) Closes.F SpringF Reverse Flow ForceVacuumFuel SystemThe operating point of the N276 changes depending on when it is activated by the engine control module. The “on” time remains the same.F Delivery PressureThe earlier N276 is activated, the more actively the delivery stroke can be used and hence the more fuel can be delivered.F Delivery PressureF Flow force, EFPFRV Energized F IVFRV De-energized F IVDelivery ChamberDelivery ChamberLegend FRV I F Feed StrokeF Flow force, EFPF SpringF SpringFuel Pressure Regulator Valve N276 Current Force Intake Valve Electric Fuel Pump Exhaust ValveIV EFP EV Current Reduction Time384_041Fig. 3 – Pump Piston Feed Stroke, Fuel Flows to Rail. – N276 Receives Short Pulse of Electrical Current from Engine Control Module. – IV Closes. Due to Upward Motion of Pump Piston, Pressure Builds Up Immediately Inside Pump. – EV Opens.Fig. 4 – Pump Piston Feed Stroke, Fuel Flows to Rail Until Intake Stroke Begins. – N276 De-energizes. – IV Closes. – EV Opens.42Fuel SystemInjectorEach fuel injector has six individual fuel openings, providing better mixture preparation. This also helps prevent “wetting” the intake valves and the combustion chamber surfaces during injection cycles. The angle of cone of the jet is 50°. These modifications have resulted in reduced HC emissions, particulate matter formation, and oil thinning.Single Port InjectorMulti Port Injector384_042384_06143Notes44Exhaust SystemTurbocharger and Manifold ModuleA turbocharger and manifold module is used. It is attached to the cylinder head by clamping flanges. Reference The exhaust gas turbocharger and manifold module, as well as the charge pressure control and the wastegate control system are described in SelfStudy Program 994503 - The 2006 Audi A3 Overview.Fuel Pump (FP) Control Module J538Coolant Flow to Radiator or from Auxiliary Water PumpCharcoal Canister ConnectionPressurized Oil InletTurbocharger Recirculating Valve N249 Coolant Inflow from Cylinder Block384_03645Notes46Engine Management SystemOverview of Bosch MED 17.5 SystemSensorsMass Air Flow (MAF) Sensor G70 Intake Air Temperature (IAT) Sensor 2 G299Engine Coolant Temperature (ECT) Sensor (on Radiator) G83Engine Coolant Temperature (ECT) Sensor G62Charge Air Pressure Sensor G31Engine Speed (RPM) Sensor G28Camshaft Position (CMP) Sensor G40Throttle Valve Control Module J338 with Throttle Drive Angle Sensor 1 G187 and Throttle Drive Angle Sensor 2 G188Engine Control Module (ECM) J623 with Ambient Pressure SensorThrottle Position (TP) Sensor G79 Accelerator Pedal Position Sensor 2 G185Brake Pedal Switch F63 Clutch Position Sensor G476 Data Bus On Board Diagnostic Interface J533Fuel Pressure Sensor G247Intake Manifold Runner Position Sensor G336 Instrument Cluster Control Module J285 Knock Sensor (KS) 1 G61Heated Oxygen Sensor (HO2S) G39 Oxygen Sensor (O2S) 2 Behind Three Way Catalytic Converter (TWC) G131 DFM Generation, Cruise Control On/Off Oil Level Thermal Sensor G26647Engine Management SystemActuatorsMotronic Engine Control Module (ECM) Power Supply Relay J271 Engine Component Power Supply Relay J757Intake Manifold Runner Control (IMRC) Valve N316Wastegate Bypass Regulator Valve N75Fuel Pressure Regulator Valve N276Fuel Pump (FP) Control Module J538 Transfer Fuel Pump (FP) G6Cylinder Fuel Injectors 1-4 N30-N34Ignition Coils with Power Output Stages N70, N127, N291, N292 Diagnostic PortThrottle Valve Control Module J338 with Throttle Drive (for Electronic Power Control (EPC)) G186Evaporative (EVAP) Emission Canister Purge Regulator Valve N80Oxygen Sensor (O2S) Heater Z19Coolant Circulation Pump Relay J151 After-Run Coolant Pump V51Camshaft Adjustment Valve 1 N205Radiator Fan Setting 1, PWM Signal384_054Leak Detection Pump V14448Engine Management SystemEngine Control ModuleThe 2.0L TFSI engine uses the Bosch MED 17 engine control module. The hardware and software components have been developed so they can be used for future projects both for gasoline and diesel engine applications. This allows maximum use with regards to functions and vehicle interfaces independent of the engine combustion configuration. Examples of this include the Electronic Pedal Control and radiator fan activation strategies. The new IFX Tricore processor family has sufficient capacity in reserve to accommodate future advancements in order to meet market requirements. Hardware in the engine control module: – Infineon IFX Tricore 1766 (Leda Light). – 80 MHz System Frequency. – 1.5 MByte Internal Flash. – Single Chip System.384_072Oxygen Sensor ControlA new feature of the MED 17.5 is the deletion of the continuous-duty oxygen sensor. Now, a nonlinear lambda sensor is installed. The sensor is located between the close-coupled pre-catalyst and the underbody catalytic converter. The function of the continuous-duty pre-cat sensor has been mapped by the new functions of the engine control module. These maps are generated by conducting appropriate tests during engine development.Operating ModesIn all operating ranges of the engine, except directly after starting (when the fuel-air mixture is slightly richer), the mixture composition is set to lambda 1. The following operating modes are implemented: – In Start Phase: High-pressure - Start of Fuel-Air Stratification. – For Several Seconds After Start: HOSP. – Following Warm-Up Phase: Engine Map Controlled Dual Injection Cycle. – At Coolant Temperatures of 80 °C or Higher: Fuel Injection Synchronous with Intake Cycle Only. The intake manifold flaps open at an engine speed of 3000 rpm.Advantages:– Fewer Potential Sources of Fault. – More Cost-Effective. – Requirements of ULEV are Met without Continuous-Duty Oxygen Sensor. – No Adjustments Needed in Customer Service or for Exhaust Emission Inspections.49Engine Management SystemSubstitute Functions in Case of Sensor/Actuator FailureSymptom in Case of Failure F63 G39 G61 G62 G83 No Cruise Control No Control No No Radiator Fan Runs Permanently in Setting 1 No Throttle Response No Throttle Response No High-pressure No No Cruise Control No Power Supply to ECM — Engine Not Running No No High-pressure Engine Not Running Smoothly Engine Not Running Smoothly No No No High-pressure NoDTC Entry Yes Yes Yes Yes NoMIL No Yes No Yes NoEPC No No No No NoSubstitute Signal No Yes Yes Yes NoPower Limitation No No Yes No NoEmergency Operation No No No No NoG79/G185 G187/G188 G247 G336 G476Yes Yes Yes Yes YesYes Yes Yes Yes NoYes Yes No No NoNo No No No NoYes Yes Yes No NoYes Yes Yes No NoJ271 J538 J757 Ignition Coils N30-N33 N75 N205 N276 N316No Yes Yes YesNo Yes Yes YesNo No Yes YesNo No No NoNo No Yes YesNo No Yes YesYes Yes Yes Yes YesYes Yes Yes Yes YesYes Yes No Yes NoNo No No No NoYes Yes No Yes NoYes Yes No Yes NoNoteThis table refers to generally occurring faults. It is no substitute for fault finding with the Workshop Manual and the “Guided Fault Finding” function. The parameters specified in the table are subject to deviation depending on fault type. Specifications are subject to change due to updating of engine control module software.50ServiceSpecial ToolsShown Here are the Special Tools for the Chain-Driven 2.0 Liter 4V TFSI Engine.384_066T10352 For Removing the 4/3-Way Central Valve of the Camshaft Adjuster384_067384_068T10353 Thrust Piece for Installing the Oil Seal on the Water Pump ShaftT10354 Thrust Piece for Installing the Oil Seal on the Front Crankshaft (Vibration Damper)384_069384_065T10355 Retainer for Removing the Crankshaft Center BoltT10359 Engine Holder for Removing the Engine with Transmission51Service384_070384_071T10360 Torque Wrench Adapter Used for Removing/Installing the Belt Drive Pulley Bolt for the Engine Coolant PumpV.A.G 133152Knowledge AssessmentAn on-line Knowledge Assessment (exam) is available for this Self-Study Program. The Knowledge Assessment may or may not be required for Certification. You can find this Knowledge Assessment at: www.accessaudi.comFrom the accessaudi.com Homepage: – Click on the “ACADEMY” Tab. – Click on the “Learning Management Center (LMC)” Link. – Type the Course Number in the Search Box. – Click “Go!” and Wait Until the Screen Refreshes. – Click “Start” to Begin the Assessment.For Assistance, please call: Audi Academy Learning Management Center Headquarters 1-866-AUDI-ALC (283-4252) (8:00 a.m. to 8:00 p.m. EST)53Notes54921703All rights reserved. Technical specifications subject to change without notice. Audi of America, Inc. 3800 Hamlin Road Auburn Hills, Michigan 48326