TECHNICAL DOCUMENTATION

SSP 990193 Audi New Technology 2009 – 2010

PDFEN98 pages10 MB
SSP 990193 Audi New Technology 2009 – 2010 - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingAudi New Technology 2009 – 2010 Self-Study Program 990193 Audi of America, LLC Service Training Printed in U.S.A. Printed 11/2009 Course Number 990193©2009 Audi of America, LLCAll rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher.All requests for permission to copy and redistribute information should be referred to Audi of America, LLC.Always check Technical Bulletins and the latest electronic repair literature for information that may supersede any information included in this booklet. Table of ContentsR8 with 5.2L V10 FSI Engine . . . . . . . . . . . . . . . . . . . . . . . . . 1Packaged Ultrasonic Level Sensor (PULS) . . . . . . . . . . . .170B5 S Tronic Transmission . . . . . . . . . . . . . . . . . . . . . . . . . .20Sport Differential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44Indirect Tire Pressure Monitoring . . . . . . . . . . . . . . . . . . . .69MMI 3G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73Knowledge Assessment . . . . . . . . . . . . . . . . . . . . . . . . . . .93The Self-Study Program provides introductory information regarding the design and function of new models, automotive components or technologies. The Self-Study Program is not a Repair Manual! All values given are intended as a guideline only. Refer to the software version valid at the time of publication of the SSP. For maintenance and repair work, always refer to the current technical literature.ReferenceNotei Notesii R8 with 5.2L V10 FSI EngineAudi continues to build on its leadership position in the high-performance sports car segment with the R8 5.2L V10 FSI quattro. The top-of-the-line model of the R8 model series was developed jointly with quattro GmbH. Its ten-cylinder engine develops 525 hp (386 kW) which is capable of delivering breathtaking performance.Audi technologies such as quattro permanent all wheel drive, lightweight aluminum body (ASF) and innovative all-LED lights propel the R8 5.2L V10 to the top of its competitive field.990193_100At a glance: Engine – Newly developed V10 with 5.2 liters displacement, FSI direct injection and dry sump lubrication – Superior performance 525 hp (386 kW) and 390 lb ft (530 Nm) of torque Power train – Six-speed manual transmission; optional sequential R tronic with paddle shifters on steering wheel and “Launch Control” function – quattro permanent all wheel drive with rear-wheel bias Chassis – Dual aluminum wishbone suspension – High-performance brakes, optional with ceramic discs – 19-inch wheels – Audi magnetic ride adaptive suspension Body and design – Lightweight, extremely rigid aluminum ASF body weighs only 436 lb (210 Kg) – Spacious interior and high level of everyday utility – Exterior and interior design with distinctive new elements – All-LED lights as standard1 R8 with 5.2L V10 FSI EngineTechnical SpecificationsEngine:Type rpm Arrangement Bore Stroke Displacement Compression ratio Fuel requirement Horsepower Torque Naturally aspirated 5.2 liter V10 spark ignition engine with FSI, 90° cylinder angle, 4-valve per cylinder, double overhead camshafts (DOHC), intake manifold with charge movement flaps 8700 rpm Mid-mounted, longitudinal 3.33 in (84.5 mm) 3.65 in (92.8 mm) 317.6 cu in (5,204 ccm) 12.5 : 1 Premium unleaded 525 hp (386 kW) @ 8000 rpm 391 lb ft (530 Nm) @ 6500 rpmEngine design:Cylinder block Connecting rods Pistons Crankcase Crankshaft Cylinder head Valve train Firing order Cooling system Lubrication system Fuel injection Emission system Fuel Aluminum alloy incorporating silicon crystals Forged steel / large ends cracked Aluminum High strength aluminum alloy casting Forged steel, 5 main bearings Aluminum alloy casting Chain-driven DOHC, continuous intake and exhaust camshaft adjustment 1–6–5–10–2–7–3–8–4–9 Water-cooled, thermostatically controlled radiator fan Dry sump oil system FSI Two metal primary catalytic converters, two metal main catalytic converters, four heated oxygen sensors, secondary air injection system Super Plus ROZ 98 (Premium unleaded — 9 AKI)Electrical system:Battery Alternator 110 amp/hour 14.0 volts 190 ampDrive train:Transmission Type Gear ratios: 1st 2nd 3rd 4th 5th 6th Reverse Final drive Center differential Viscous clutch 6-speed manual with launch control / optional R tronic with launch control Manual 4.373 2.709 1.925 1.502 1.239 1.035 3.713 3.077 R tronic 4,373 2.709 1.925 1.502 1.239 1.035 3.713 3.077Steering:Type Ratio Turning circle (curb to curb) Hydraulically assisted rack-and-pinion 17.3 38.7 ft (11.8 m)2 R8 with 5.2L V10 FSI EngineSuspension:Front Rear Double aluminum wishbone Double aluminum wishboneBrakes:Service brake: Discs/calipers Front Rear Parking brake Disc brakes, internally vented / eight piston calipers at front, 4 piston calipers at rear 14.4 in (365 mm) 14.4 in (365 mm) Mechanically actuated at the rear wheelsWheels (standard only):Size Front: 8.5J x 19, Rear: 11J x 19 AlloyTire (standard only):Size Front: 235/35 91Y, Rear: 295/30 100YBody:Material Corrosion protection Multi-step anti-corrosion protection Audi Space Frame (ASF)Capacity:Engine oil Fuel tank Reserve Cooling system 12.7 qt (12.0L) 23.8 gal (90L) 2.6 gal (10L) 5.3 gal (24.0l) [see next page]Exterior dimensions: Interior dimensions:Seating capacity EPA class Head room Shoulder room Leg room Interior volume (EPA) Luggage capacity trunk / behind seats2 n/a n/a n/a n/a n/a 3.5 cu ft (100L) / 3.18 cu ft (90L)Performance:5.2 FSI quattro - manual 0 - 60 mph 0 - 100 km/h 0 - 200 km/h Top speed Lateral acceleration 1.2 g Manual 12.0 mpg 20.0 mpg 15.0 mpg R-tronic 13.0 mpg 20.0 mpg 15.0 mpg 3.7 seconds 3.9 seconds 12.0 seconds 196 mph (316 km/h) 5.2 FSI quattro - R tronic 3.7 seconds 3.9 seconds 12.0 seconds 196 mph (316 km/h)Fuel economy (EPA estimate):City Highway Combined3 R8 with 5.2L V10 FSI EngineDimensions49.2 in (1252 mm)64.4 in (1638 mm) 75.9 in (1930 mm)62.7 in (1595 mm) 79.8 in (2029 mm)39.4 in (1003 mm)104.3 in (2650 mm) 174.6 in (4435 mm)37.7in (958 mm)30.7 in (782 mm)54.8 in (1392 mm)990193_101 4 R8 with 5.2L V10 FSI EngineLike the R8 4.2L, the R8 5.2L V10, uses an Audi Space Frame of aluminum and ultra-light magnesium. It is produced largely by hand in the Neckarsulm manufacturing plant of quattro GmbH. Maximum precision and the use of the most advanced joining techniques are employed. This includes: 325 ft (99 meters) of welding seams, 782 rivets, and 308 selftapping screws that hold the body together. A fully automatic measuring system checks the dimensions of every body with precision in the one-tenth of a millimeter range.990193_102Casting (aluminum)990193_103Section (aluminum) Sheet metal (aluminum) Magnesium5 R8 with 5.2L V10 FSI Engine5.2L V10 FSI EngineThe V10 for the R8 has a total displacement of 5,204 cc and is designed for high-performance. Specific power output for the R8 V10 is 100.9 hp per liter of displacement. Each horsepower of the engine only needs to move 6.81 lb (3.09 kilograms) of weight. When equipped with a manual transmission, the vehicle only weighs 3571 lb (1,620 kilograms). The 10-cylinder layout is an ideal design solution for maximum performance. Compared to a V8 with the same displacement, a V10 has smaller and lighter pistons and connecting rods, which makes it a free-revving engine. Compared to a V12, it has fewer components, resulting in lower moving masses and less internal friction. Even with all attached components, the 10-cylinder engine is only 25 inches (646 mm) long, 29 inches (737 mm) wide, and 27 inches (696 mm) high.990193_1046 R8 with 5.2L V10 FSI EngineSpecificationshp (kW) 600 (450) lb ft (Nm) 530 (720)540 (400)470 (640)470 (350)410 (560)400 (300)350 (480)340 (250)300 (400)990193_113270 (200)230 (320)200 (150)180 (240)Displacement: Horsepower:317.8 cubic inches (5204 cc) 525 hp SAE (386 kW) @ 8000 rpm 391 lb ft (530 Nm) @ 6500 rpm 8700 Premium unleaded130 (100) Power output 70 (50) Torque120 (160)Maximum torque: Maximum rpm:60 (80)Fuel requirement:00990193_110Type: Arrangement: Bore: Stroke: Compression ratio: Cylinder block: Connecting rods: Pistons: Crankcase: Cylinder head: Valve train: Firing order: Cooling system: Lubrication system: Fuel injection/ignition system: Emission system: Fuel:5.2 liter V10 spark-ignition with FSI, 90° cylinder angle, 4 valve technology, DOHC, intake manifold with charge movement flaps, naturally aspirated Longitudinal, mid-engine installation 3.33 inches (84.5 mm) 3.65 inches (9.28 mm) 12.5:1 Aluminum alloy Forged steel Aluminum High strength aluminum alloy casting Aluminum alloy DOHC chain driven, continuously variable intake and exhaust camshaft adjustment 1-6-5-10-2-7-3-8-4-9 Water cooled, thermostatically controlled radiator fans Dry sump oil system FSI direct injection Two metal primary converters, two main converters, four heated O 2 sensors, secondary air system Super Plus ROZ 98 / Premium unleaded (91 AKI)7 R8 with 5.2L V10 FSI EngineThe crankcase is produced by a low-pressure die-casting method. It is made from hypereutectic aluminum-silicon alloy — a high-tech material that combines low weight with high strength. The high silicon content of this alloy gives the cylinder walls the necessary wear resistance to withstand very high average piston velocity.The bedplate design — the lower bearing brackets for the crankshaft are integrated into a single frame — provides the crankcase with maximum rigidity and optimal vibration behavior. Integrally cast iron bearing brackets reduce thermal expansion of the aluminum housing and minimize play in the main crankshaft bearings. The forged crankshaft and forged-steel con rods combine high strength with low weight. The pistons are forged of a high-strength aluminum alloy.431_046With the dry-sump lubrication system there is no oil pan. The engine has an intake module connected directly to the external oil pump via intake ports.This intake module does not have a large oil reservoir. Instead it serves as a baffle plate and collects the outflowing oil generated by the rotation of the crankshaft.431_0748 R8 with 5.2L V10 FSI EngineThe crankshaft has been designed as a common-pin type crank pin, and not a split-pin type as on the 5.2L V10 engine used in the Audi S6.431_066 Split-pin crankshaft 431_044 Common-pin crankshaftThe camshafts, as well as the oil pump, the water pump, and parts of the accessory sub-systems, are driven by maintenance-free chains located on the rear wall of the engine. All four camshafts are adjustable through a 42° crank angle, which provides a wide range of control timing. The valves are actuated by roller-mounted cam followers. The exhaust valves are subject to a high thermal load and are lined with sodium to assist in cooling.431_0429 R8 with 5.2L V10 FSI EngineDry Sump Lubrication SystemThe oil pump module is external to the engine and is chain-driven. The pump consists of a suction and feed pump for filling the oil reservoir, and a suction and pressure pump for supplying oil to the engine. The oil pump and coolant pump are paired to form a single unit, so they can only be replaced as a unit. Only the thermostat housing and integrated coolant thermostat can be replaced separately.990193_105Water pump Oil return from right cylinder headTo main oil port10 R8 with 5.2L V10 FSI Engine1412 132 4 1 6 3 5 7 10 11 9 8431_025Legend1 2 3 4 5 6 7 Crankshaft chamber 5 Chain case return line Oil return from right cylinder head Oil return from left cylinder head Crankshaft chamber 4 Crankshaft chamber 3 Crankshaft chamber 2 8 9 10 11 12 13 14 Crankshaft chamber 1 To oil thermostat To main oil port From oil reservoir Suction pump Pressure pump Crankcase divider11 R8 with 5.2L V10 FSI EngineIn combination with an oil-to-water heat exchanger located in the inner V of the engine, the 5.2L V10 uses a thermostatically controlled airflow-type oil cooler to regulate engine oil temperature. It is mounted behind the left side-blade the body. When the engine oil is cold, the re-circulating, extracted oil is pumped into the oil thermostat housing. When the thermostat is in a closed state, it seals off the inlet leading to the oil cooler, while the oil in the thermostat housing is redirected to the oil reservoir.When the temperature of the oil exceeds 212°F (100°C), the oil thermostat opens the inlet to the oil cooler. An expanding element in the thermostat exerts pressure against the thermostat housing. Due to the pressure of the expanding element, the thermostat is displaced against the force of a spring, opening the channel, and simultaneously closing off the inlet leading directly to the oil reservoir. Oil flows through this port and into the oil cooler, returning from there to the oil thermostat housing before entering the oil reservoir.Oil cooler, located behind left side blade990193_10712 Notes13 R8 with 5.2L V10 FSI EngineMass Air Flow Sensor G70 Intake Air Temperature Sensor G42Throttle Position Sensor G79 Accelerator Pedal Position Sensor -2- G185Engine Speed Sensor G28Powertrain CAN-BusKnock Sensors -1- and -2- G61, G62Fuel Pressure Sensor G247Camshaft Position Sensor G40 Camshaft Position Sensor -3- G300 Engine Control Module J623Throttle Valve Control Module J338 Throttle Drive Angle Sensors -1- and -2- G187, G188 Throttle Drive G186Engine Coolant Temperature Sensor G62Low Fuel Pressure Sensor G410Intake Manifold Runner Position Sensor G336 Heated Oxygen Sensor G39 Oxygen Sensor Behind 3-Way Catalytic Converter G130 Heated Oxygen Sensor -2- G108 Oxygen Sensor -2- Behind 3-Way Catalytic Converter G131Brake Booster Pressure Sensor G294Brake Light Switch F Brake Pedal Switch F47 Additional Signals: Oil Temperature Sensor -2- G664 Secondary Injection Sensor -1- G609 Clutch Position Sensor G476 Cruise Control ON/OFF Park/Neutral Signal Terminal 50 Wake Up Signal from Driver’s Door Switch via J393 Mass Air Flow Sensor G246 Intake Air Temperature Sensor -2- G299 Engine Control Module -2- J624 Camshaft Position Sensor -2- G163 Camshaft Position Sensor -4- G301 Throttle Valve Control Module -2- J544 Throttle Drive Angle Sensors -1- and -2- G297, G298 Knock Sensors -3- and -4- G198, G199 Heated Oxygen Sensor -3- G285 Oxygen Sensor -3- Behind 3-Way Catalytic Converter G287 Heated Oxygen Sensor -4- G286 Oxygen Sensor -4- Behind 3-Way Catalytic Converter G288 Intake Manifold Runner Position Sensor -2- G512 Secondary Air Injection Sensor -2- G610 Fuel Pressure Sensor -2- G62414 R8 with 5.2L V10 FSI EngineFuel Pump Control Module J538 Transfer Fuel Pump G6 Ignition Coils 1-5 with Power Output Stage N70, N291, N292, N323, N127; Cylinders 1-5Fuel Metering Valve N290 Evaporative Emission Canister Purge Regulator Valve N80 Right Electro-Hydraulic Engine Mount Solenoid Valve N145Intake Manifold Runner Control (IMRC) Valve N316 Starter Relay J53; Starter Relay -2- J695 Leak Detection Pump V144Exhaust Flap Valve -1- N321Fuel Injectors N30, N31, N32, N33, N83 Cylinders 1-5Camshaft Adjustment Valve -1- N205 Camshaft Adjustment Valve -1- (exhaust) N318Throttle Drive (for EPC) G186 Coolant Recirculation Pump Relay J151 After-Run Coolant Pump V51 Oxygen Sensor Heater Z19; Oxygen Sensor -1- Behind 3-Way Catalytic Converter Heater Z29; Oxygen Sensor -2- Heater Z28; Oxygen Sensor -2- Behind 3-Way Catalytic Converter Heater Z30 Data Link Connector Secondary Air Injection Pump Relay J299 Secondary Air Injection Pump Motor V101 Secondary Air Injection Solenoid Valve N112 Brake Booster Relay J569 Brake System Vacuum Pump V192Engine Component Power Supply Relay J757 Engine Control Module Power Supply Relay J271 Additional Signals: Coolant Fan Control (FC) Control Module J293 Coolant Fan Control (FC) Control Module -2- J671 Ignition Coils 6-10 with Power Output Stage N324-N328 Cylinders 6-10 Secondary Air Injection Pump Relay -2- J545; Secondary Air Injection Pump Motor -2- V189; Secondary Air Injection Solenoid Valve -2- N320 Camshaft Adjustment Valve -2- N208 Camshaft Adjustment Valve -2- (exhaust) N319 Fuel Injectors N84-N86, N299-N300; Cylinders 6-10 Oxygen Sensor -3- Heater Z62; Oxygen Sensor -3- Behind 3-Way Catalytic Converter Heater Z64; Oxygen Sensor -4- Heater Z63; Oxygen Sensor -4- Behind 3-Way Catalytic Converter Z65 Evap. Emission Canister Purge Regulator Valve -2- N333 Fuel Metering Valve -2- N402 Left Electro-Hydraulic Eng. Mount Solenoid Valve N144990193_114 15Throttle Drive -2- G296 R8 with 5.2L V10 FSI EngineDistinguishing Features of the 5.2L V10 R8Audi is the world’s first automaker to use LEDs for high beam, low beam, daytime running lights, and turn signals. In this highly complex technology, lens and reflector systems, intelligent ballasts, and fan driven coolers interact. Although the LEDs emit cool light, they heat up, and their temperature must be kept within a defined range.With a color temperature of 6,000 Kelvin, the LED light closely resembles white daylight, which is less tiring to the eyes when driving at night. Excellent light distribution and virtually unlimited LED service life are additional benefits. Their energy consumption is also substantially lower than halogen lights.990193_112The rear fascia of the R8 5.2L V10 features high-gloss black as the dominant color. LEDs mounted in tubular housings create a threedimensional lighting effect. The rear fascia air outlets have only two cross braces, and the exhaust system terminates in two large, oval tailpipes. The fully enclosed underbody ends in a diffuser with a pronounced upward sweep. The rear spoiler automatically deploys at 62 mph (100 km/h.)990193_11116 Packaged Ultrasonic Level Sensor (PULS)New Oil Level SensorA new generation engine oil level sensing system has been introduced by Audi. It is referred to in the technical literature and VAS Scan Tool as: PULS — Packaged Ultrasonic Level Sensor. Vehicles using this system can be identified by the absence of an oil dipstick. PULS operates on an ultrasonic principle. Ultrasound pulses generated by the oil level sensor are reflected by the oil-air boundary layer. This type of level sensor replaces the older Thermal Oil Level Sensor (TOLS) that used the hot-wire principle. With PULS, oil level is calculated by the engine control module, which factors the difference between transmitted and reflected pulses of the oil level sensor, and the speed of sound. The driver can view oil level information via the MMI under the heading CAR. In addition, minimum and maximum oil level warnings are displayed in the Driver Information Display of the instrument cluster.Virtual cylinder 0.7 in (20 mm) diameter free of reflective surfacesUpper oil panOil level sensorLower oil pan Static measurement range 2.9 – 4.7 in (75 – 120 mm) 411_100 Dynamic measurement range 0.6 – 2.9 in (15 – 75 mm)Zero reference point of systemUltrasonic signals are processed electronically by circuitry in the oil level sensor and are transmitted to the instrument cluster through a Pulse Width Modulated (PWM) signal.Advantages of the PULS versus a Thermal Oil Level System (TOLS): – The sensor signal is available quickly (approx. 100 ms for ignition ON) – Low electrical power consumption (approx. 0.5A)17 Packaged Ultrasonic Level Sensor (PULS)Oil Level ScaleThe Engine Control Module calculates oil level in the engine. This information is transmitted to the Powertrain CAN-bus where it is read by the instrument cluster and MMI, which then pass this information on to other subsystems via Data Bus On Board Diagnostic Interface J533. Because the dipstick has been eliminated, the customer can only check the oil level via the instrument cluster or MMI displays. Checking the oil in the workshop requires special tool T40178. The tool must be calibrated for each individual engine. The adjustment ring is first set to the correct position, then the oil level is read on the oil level scale. The correct setting position value for T40178 can be found in the repair manual maintenance section. Oil level is calculated both dynamically (vehicle moving) and statically (vehicle stationary).Oil level scale T40178Adjustment ring411_105Dynamic MeasurementThis measurement method is preferred because it provides more accurate results. The measurement process is interrupted when: – Vehicle acceleration rate is greater than 6.7 mile/hour seconds (3 meter/sec2) – Oil temperature is greater than 284°F (140°C) – Engine hood has been opened The following criteria are evaluated: – Engine speed – Longitudinal and transverse acceleration – Engine temperature – Engine Hood Switch F266 position (open/closed) – Number of miles (km) driven since the last opening of Engine Hood Switch F266 (more than 30 miles [50 km]) – Number of measurement values generated within the driving cycleStatic MeasurementThis measurement is performed: – At ignition ON (however, the signal is transmitted as soon as the driver’s door is opened in order to obtain a level signal quickly – Engine speed less than 100 rpm – Engine at standstill for longer than 60 seconds – Engine temperature over 104°F (40°C) The longitudinal and transverse acceleration values, as well as the parking brake position are also used to determine vehicle status when measurements are made.18 Packaged Ultrasonic Level Sensor (PULS)Oil level can be checked by the customer using the MMI, under the CAR menu.Oil LevelMax Engine oil level o.k.Min411_096The following graphics can be displayed in the DIS of the instrument cluster.In addition, there is a display that indicates overfilling of the system, and a display that indicates if the oil level sensor has failed.MaxMaxMaxPlease add max. 1 qt oil. Continued driving possible. MinOil level is o.k.Urgent: Please add oil. Min Min35540 D4m 1975.5 27° F 411_09735540 D4m 1975.5 27° F 411_09835540 D4m 1975.5 27° F 411_09919 0B5 S Tronic Transmission0B5 7-Speed Dual Clutch TransmissionFollowing the success of the six-speed S tronic on the Audi A3 and Audi TT models, a seven-speed dual-clutch transmission, combined with the quattro powertrain, is now available for the first time in a longitudinal configuration. The 0B5 S tronic transmission combines the positive features of an automatic transmission with the sportiness and efficiency of a manual gearbox. It provides extremely short shift times without interruption of tractive power to provide a special driving experience.Specifications of the 0B5 transmissionDesignationsManufacturer: DL501-7Q Service: 0B5 Distribution: S tronic Audi AG Ingolstadt VW plant, Kassel Seven-speed, dual-clutch gearbox; fully synchronized, electro-hydraulically controlled Dual oil-cooled multi-plate clutches, electro-hydraulically controlled Mechatronic system — integrating the hydraulic control module, electronic control module, some sensors and actuators; sport program and “tiptronic” shift program for manual gear shifting Up to 8.1 : 1* 3.503 in (89.0 mm) Up to 406.6 lb ft (550 Nm) at 9000 rpm Approx. 313.0 lb (142 kg), including dual-mass flywheel and oil fillDevelopment production Type Dual clutch ControlRatio spread Shaft spacing Torque capacity Weight*7th gear is configured as an overdrive gear. Top speed is in 6th gear.20 0B5 S Tronic TransmissionVent for ATF system (hydraulic controls/ dual clutch) Final drive/ differential (forward of the dual clutch)Vent for gear oil system (gears/transfer case/ front axle drive)429_124Connection for Mechatronic module Transmission plate with dualmass flywheelATF, filler and oil level checking bolt Connection to ATF coolerDual clutch (K1, K2)Oil drip pans Seven-speed gearbox assemblyCenter differential Final drive with welded ring gear and special tooth geometry to accommodate the angled side shaft429_128 Bi-planar angled side shaft Spur pinion with special tooth geometry which allows the shaft to rotate at an angle in two planes (beveloid gearing) Gear lever21 0B5 S Tronic TransmissionComponent Parts OverviewDual mass flywheelDual clutch (K1, K2)Stop Transmission plateHydraulic control (Mechatronic Connection system) module for ATF cooler Direct Shift Gearbox (DSG) Mechatronic J743Electric connectionOil drain port22 0B5 S Tronic TransmissionAdvantages of Seven Gear RatiosSeven forward gears provide a wide ratio spread that boosts initial acceleration, while also lowering fuel consumption via the 7th (overdrive) gear.Gear leverOil drip panServiceable offset depth for all shaft oil seals when replacedSelector rail Gear oil fill and level checking bolt Self-locking center differential with 40/60 asymmetric/dynamic torque split. The asymmetric-dynamic power distribution provides sporty and agile driving characteristics with slight emphasis to the rear axle. When needed, the center differential can deliver up to 85% power to the rear axle or a maximum of 65% power to the front axle. 429_11623 0B5 S Tronic TransmissionGearbox Design — FunctionDrive is transmitted to the dual mass flywheel through the transmission plate. From there, torque is transmitted to electro-hydraulically controlled clutches (K1, K2) which operate even or odd numbered gears. The gear arrangement of the 05B transmission can be viewed as two separate gear boxes.Sub-Gearbox 2Even numbered gears (2, 4, 6) and the reverse gear are driven through input shaft 2 (a hollow shaft) by clutch K2. Power output is through the common output shaft, with torque transmitted directly to the center differential. Torque distribution is approx. 60% to the flange shaft connected to the rear axle, and approx. 40% to the spur pinion and side shaft connected to the front axle drive (not shown here).Sub-Gearbox 1Odd numbered gears (1, 3, 5, 7) are driven through central input shaft 1 by clutch K1.Clutch K1 Clutch K2Input shaft 2Transmission plateParking lock gear Dual mass flywheel6th gear 4th gear 2nd gear Reverse (R) gearDesign Features of the Dual ClutchThe dual clutch serves two tasks: – To engage the engine at initial acceleration and to disengage the engine when stopping – To shift the gears The dual clutch was designed so that clutch K1 is located on the outside, making it a larger diameter. This meets the higher demands placed on K1 as the starting clutch (in first gear). Small pressure cylinders and coil spring assemblies on both clutches provide good control during initial acceleration and when changing gears. Hydraulic pressure equalization is no longer required. Clutch control corrects dynamic pressure build-up caused by centrifugal forces at high engine speeds in any situation.24 0B5 S Tronic TransmissionGear Shifting SequenceInitial AccelerationIn selector lever position P or N, only 1st gear and reverse are engaged. This allows immediate acceleration from a standing stop. Regardless of whether the driver decides to drive in reverse or to go forward, the correct gears are already pre-selected.ShiftingTo drive forward, the driver shifts the selector lever into D and drives away in 1st gear. When a defined speed threshold of approx. 10 mph (15 km/h) is exceeded, 2nd gear is engaged in sub-gearbox 2 (reverse was previously engaged). When the shift point for upshifting from 1st to 2nd gear is reached, the gearshift is made by the rapid opening of clutch K1 and simultaneous rapid closing of clutch K2 without any interruption in tractive power. To enhance shift comfort and preserve the clutch, engine torque is reduced during the gearshift (overlap). The gear shifting process is completed within a few hundredths of a second. 3rd gear is now pre-selected in sub-gearbox 1. The process described above repeats itself alternately during the subsequent gearshifts from 2-3 up to 6-7.Input shaft 1Spur pinion/ output to front axle (beveloid gearing)Output to rear axle differential7th gear 5th gear 3rd gear 1st gear Center differential 429_134SynchromeshTo facilitate extremely short shift times, all gear synchronizers are carbon coated. Gears one, two, and three are also triple cone synchronizers due to the high stresses to which they are subjected. Gears 4, 5, 6, and 7 use single cone synchronizers.25 0B5 S Tronic TransmissionTransmission Oil SystemsATF Oil SystemThe 0B5 transmission has two separate oil systems. The first oil system accommodates the dual clutch, Mechatronic system, and oil supply. These components use an ATF developed specifically for the 0B5 transmission. This ATF system enables rapid shifting even at low temperatures, while also lubricating and cooling the dual clutch.Dual clutch429_126 Mechatronic systemATF pumpNote ATF oil is subject to a fixed replacement interval (refer to maintenance). Hypoid gear oil is designed for lifetime use.Gear Oil SystemThe second oil system incorporates the gear assembly, the transfer case (center differential), and the front axle drive. Lubrication is by means of a hypoid gear oil with a special oil additive for the center differential. Separating these oil chambers made it possible to design the individual component parts of the transmission optimally. It was not necessary to make any compromises due to conflicting demands on the lubricants.Front axle differential 429_127 Gear assembly Transfer case26 0B5 S Tronic TransmissionGear Oil SystemThe oil chambers must be reliably sealed off from one another. The ingress of gear oil into the ATF oil chamber (the ATF mixes with the gear oil) would adversely affect the performance of the dual clutch. To prevent this from occurring, special sealing elements are fitted in relevant places.429_121Double oil seal ring Input shaft 1Transverse boreDouble oil seal ring Input shaft 2 Oil drain port, refer to Fig. 116 on page 23 The 4 selector rails are sealed by means of double-sided axial sealing elements. Axial sealInput shafts 1 and 2 are sealed by a double oil seal ring. In total, four radial sealing rings are used. If a radial seal is leaking, a oil drain port allows the leaking oil to drain off and prevents it from entering the other oil chamber. The transverse bore in input shaft 2 establishes a connection between input shaft 1 and the oil drain port.27 0B5 S Tronic TransmissionATF Oil Supply — LubricationATF Pump with Rotating Port and Dual Clutch BearingA sufficient supply of ATF oil is essential for the operation of the transmission. An external gear pump driven by the dual clutch through a gear step provides necessary oil flow and oil pressure. The ATF pump supplies the Mechatronic system with the oil pressure required to perform the following functions: – Control of the multi-plate clutch (engagement and disengagement) – Cooling and lubrication of the multi-plate clutch – Control of gearbox hydraulicsPressure line K1Dual clutch Pressure line K2 Rotating port 429_138Suction jet pumpOil pump driveSuction filter429_122ATF pump (external gear pump)A suction jet pump, operating on the Venturi principle, increases the cooling oil flow for the clutch cooling system. Because this pump doubles the cooling oil flow rate without the need for increasing oil pump capacity, it is smaller and more efficient.28 0B5 S Tronic TransmissionATF CoolingATF cooling is provided by a heat exchanger integrated into the engine cooling system (ATF cooler). The supply line running to the ATF cooler accommodates a pressure filter, which, in conjunction with the suction filter, provides effective filtering of the ATF. Both filters are designed for lifetime use in the transmission, and are not subject to a replacement interval. A differential pressure valve is integrated in the pressure filter. It opens when the flow resistance rises above a threshold value, for example when the filter is clogged or the ATF is very cold. Therefore, circulation to the ATF cooler is always assured. Notes on the ATF cooler: If the ATF cooler is leaking, coolant will mix with the ATF. Even the smallest amounts of coolant in the ATF will impair clutch control. The new glycol test 8E0 398 998 can be used to determine whether the ATF contains glycol. Notes on the ATF filter: It is only necessary to replace the pressure filter if the ATF has been contaminated due to transmission damage. If swarf (metal chips), abraded matter, or other foreign material is found mixed in with the ATF, the ATF cooler must be flushed, and if necessary, replaced.ATF cooler Engine cooling system with ATF coolerThe illustration on this page shows the ATF cooling system connected to the 2.0L TFSI engine. This configuration is representative of all Audi engines, with the exception of different wiring harnesses.Connection module ATF filter (pressure filter)**In the future, the pressure filter will be integrated into the connection module.429_13529 0B5 S Tronic TransmissionGear Assembly LubricationSelective lubrication, conducted via special oil passages and oil drip pans, results in lower oil level requirements. This innovative lubrication design reduces churning losses and enhances overall transmission efficiency. The bearings for the input shaft change gears are lubricated through the hollow drilled input shaft 1. Transverse bores in the shafts direct the oil to the bearing points.Oil drip pansOil passage in input shaft 1429_125Bi-planar angled side shaftOil passage to front axle driveLubricant is supplied to the center differential through the hollow drilled output shaft30 0B5 S Tronic TransmissionParking LockThe 0B5 transmission requires a parking lock since both clutches are open (disengaged) whenever the engine is not running. The parking lock gear is connected to the output shaft. The pawl is actuated mechanically by the selector lever via the selector lever cable. Drive Position Sensor G676 is also actuated through the selector shaft and the parking lock lever. For this purpose, a permanent magnet exerting a magnetic field on the sensor is located on the parking lock actuating lever. Utilizing the signals generated by Drive Position Sensor G676, the Mechatronic module recognizes the position of the selector lever (P, R, N, D, or S).StopGear leverDir ectDrive Position Sensor G676ionof T rav elPermanent magnet429_117 Parking lock gear Locking pawlNote The parking lock gear and pawl lock all four gears through the center differential, but can compensate through the center differential if a raised wheel is able to turn freely, for example, when changing a wheel. Therefore, as a precaution, the parking brake must always be applied, in these situations.Parking lock in selector lever position P (locking pawl engaged)31 0B5 S Tronic TransmissionTransmission ControlDirect Shift Gearbox Mechatronic J743The transmission is controlled by a newly developed Mechatronic system. It enables precision control of gear engagement speed and force when changing gears. This means that regardless of the driving situation, rapid gear shifts are also smooth. The Mechatronic system acts as the central transmission control module. It combines the electro-hydraulic control module (actuators), the electronic control module, and some of the sensors into a single unit. Because of the longitudinal configuration, the rpm sensors of both gearbox input shafts and the gear sensor are located on a separate mounting bracket (PCB 3).XGear selector moduleXXGear Position Distance Sensor 4 G490 (for gear selector 4-6) Gear Position Distance Sensor 3 G489 (for gear selector 7-5)XClutch Oil Temperature Sensor G509XGear Position Distance Sensor 2 G488 (for gear selector 1-3)Transmission Input Speed Sensor 3 G641 (clutch input speed)Gear Position Distance Sensor 1 G487 (for gear selector 2-R)PCB 2PCB 1429_133Electro-hydraulic control moduleXMounting points in the transmission case32 0B5 S Tronic TransmissionThe Mechatronic system controls, regulates, and performs the following functions: – Adaptation of oil pressure in the hydraulic system to requirements – Dual clutch regulation – Clutch cooling regulation – Shift point selection – Transmission control and regulation – Communication with other control modules – “Limp home” program circuitry – Self-diagnosticsNote When replacing the Mechatronic system, various adaptations must be made using the VAS Scan Tool.Note When handling the Mechatronic system, it is important to pay close attention to the working guidelines regarding electrostatic discharge!X XCenter differentialConnector Sensor module wiring harnessX XDrive Position Sensor G676X X XConnector: Mechatronic wiring harnessTransmission Input Speed Sensor G612 Transmission Input Speed Sensor1 G632429_130Connector: Gearbox Control Module PCB 2Connector: Gearbox Control Module PCB 1 Electronic module Connector: wiring harness (sensor module)Wiring harness/ cable ductXMounting points in the transmission case33 0B5 S Tronic TransmissionHydraulic Component OverviewThis illustration shows the electro-hydraulic control module, together with all components activated by the actuators. N433 Sub Transmission 1 Valve 1 (for gear selector 1-3) N434 Sub Transmission 1 Valve 2 (for gear selector 7-5) N435 Sub Transmission 1 Valve 3 (for clutch valve K1, activation) N436 Sub Transmission 1 Valve 4 (for pressure regulation in sub-gearbox 1) N437 Sub Transmission 2 Valve 1 (for gear selector 2-R) N438 Sub Transmission 2 Valve 2 (for gear selector 4-6) N439 Sub Transmission 2 Valve 3 (for clutch valve K2, activation) N440 Sub Transmission 2 Valve 4 (for pressure regulation in sub-gearbox 2) N471 Cooling Oil Valve N472 Main Pressure Valve GS = Gear SelectorShift fork 4-6 GS 4-6GS 7-5GS 1-3Shift fork 7-5 GS 2-RShift fork 2-RShift fork 1-3Note Before installing the Mechatronic system into the transmission, the gear selectors and selector rails must be brought into alignment with each other. Refer to the repair manual.The selector rails/shift forks have no stops, with the shift forks held in position by gear selectors. The only stops are in the gear change sleeve and the synchronizer assembly.34 0B5 S Tronic TransmissionDual clutch N438 (4-6) Electro-hydraulic control module — gear selector moduleN434 (7-5)N433 (1-3)N437 (2-R)ATF pump with rotating port for the dual clutchGear selectorElectro-hydraulic control module N471 N439 N435 N440N472N436 429_12935 0B5 S Tronic TransmissionElectronicsIntegrated SensorsThe transmission control module, the four distance sensors and the two hydraulic pressure sensors are combined as a non-separable unit. Two temperature sensors are integrated into the TCM. One sensor is positioned to supply precise ATF temperatures. The other sensor is integrated directly into the processor and measures critical component temperatures. The two temperature senders monitor each other for plausibility. Electronics temperature monitoring is very important so that temperature reduction measures can be made quickly, as needed. Besides safety, ATF temperature is relevant to both clutch control and hydraulic control. For this reason, ATF temperature is also a key factor in control and adaptation functions. Automatic Transmission Hydraulic Pressures Sensors 1 and 2 are utilized for clutch pressure monitoring and for adaptation of the primary pressure and sub-gearbox pressures.Gear Position Distance Sensor 4 G490 (for gear selector 4-6)Gear Position Distance Sensor 3 G489 (for gear selector 7-5)Gear Position Distance Sensor 2 G488 (for gear selector 1-3)Permanent magnet Hall sensorGear Position Distance Sensor 1 G487 (for gear selector 2-R) Automatic Transmission Hydraulic Pressure Sensor 1 G193Automatic Transmission Hydraulic Pressure Sensor 2 G194429_137Control module temperature sensorSelector railFour distance sensors determine the position of each selector rail/shift fork. The TCM requires this information to immediately diagnose non-allowed positions and to activate a “limp home” program, if necessary. An exact travel measurement is also essential for precision gear shifting. The various phases of the synchronization and gearshifting processes can then be activated sequentially.Temperature sensor in processor429_136Transmission control module36 0B5 S Tronic TransmissionA distance sensor consists of two Hall sensors and two permanent magnets which are attached to the selector rail. Depending on the position of the magnets in relation to the Hall sensors, the Hall sensors output a voltage which corresponds to the distance traveled. The travel signal is generated by evaluating both voltage signals.Note To measure the precise distance traveled by the gear selector, the shift mechanism must be adapted to the transmission control module using the VAS Scan Tool.429_171Separate SensorsTransmission Input Speed Sensors 1 and 2, as well as the gear sensor are mounted together on a common mounting bracket (PCB 3). Both engine speed senders are “intelligent sensors.” With three Hall sensors and the corresponding evaluation electronics, it is possible to distinguish between driving forward, driving in reverse, and a weak magnetic field. The control module receives the information from the senders pre-evaluated in the form of a pulse width modulated signal. The various states are indicated to the control module by different pulse widths. For example, when driving forward, the engine speed signal has a different pulse width than when reversing.Signal Use– Determination of the clutch output speed for computing clutch slip – Determination of the synchronization speed for shift controlEncoder disc, input shaft 2Drive Position Sensor G676Encoder disc, input shaft 1Connector Sensor module/wiring harness429_173Transmission Input Speed Sensor 2 G612 Transmission Input Speed Sensor 1 G632 PCB 3 (sensor module)37 0B5 S Tronic TransmissionDrive Position Sensor G676G676 is located in the gearbox and is an integral part of the sensor module. This is a contactless travel sensor which is used to determine the selector lever positions (P, R, N, D, and S). A permanent magnet exerting a magnetic force on the gear sensor is located on the parking lock lever. The parking lock lever is connected to the gear lever by a shaft. It is actuated by the selector lever by means of a selector lever cable.Drive Position Sensor G676Connector Sensor module/ wiring harness to gearbox control module429_167Permanent magnetPCB 3 (sensor module)Parking lock leverThe transmission control module requires data on selector lever position to perform the following functions and generate the following signals and information: – Information on driver input/vehicle operating state (forward, reverse, neutral) for activation of the clutches and gear selectors – Information for selection of shift program “D” or “S” – Signal for controlling the starter inhibitor – Signal for controlling the P/N lock (shift-lock) – Information for reverse gear (for example, back-up lights, Park Assist System, etc.) – Control of the selector lever position indicator in the instrument cluster and gearshift mechanismThe position sensor is a PLCD travel sensor. The abbreviation PLCD stands for Permanent Magnetic Linear Contactless Displacement sensor and describes a contactless sensor which measures linear travel using a permanent magnet. The signal generated by this sensor is very important for gearbox control and is safety-critical. For this reason, G676 consists of two redundant sensors arranged in parallel. The TCM always evaluates both sensors.Note The gear sensors must be adapted to the transmission control module using the VAS Scan Tool.38 0B5 S Tronic TransmissionTransmission Input Speed Sensor -3- G641 and Clutch Oil Temperature Sensor G509Outer plate carrier of clutch K1X Cooling oil outlets PCB 2XX = plugged connection to gear selector valve X Clutch Oil Temperature Sensor G509Connector to transmission control moduleTransmission Input Speed Sensor -3- G641Sensors G641 and G509 are integral parts of PCB2. G641 is a Hall sensor. It measures the input speed of the dual clutch (engine speed after the dual-mass flywheel). The outer plate carrier of clutch K1 serves as an encoder disc. The clutch input speed signal: – Allows more precise clutch control – Is used for adapting the clutches – Is used for regulating micro-slipG509 measures and monitors the temperature of the cooling oil emerging from the dual clutch. Clutch temperature can be derived from this information. When a defined oil temperature is reached, safety precautions are taken to prevent a further rise in temperature.39 0B5 S Tronic TransmissionTransmission Protection FunctionsControl Module Temperature MonitoringHigh temperatures have a negative impact on the useful life and performance of electronic components. Due to the integration of the transmission control module into the transmission housing (lubricated by ATF), it is very important to monitor the temperature of both the electronics and ATF. When the temperature reaches approx. 275°F (135°C) (measured by one of the two temperature sensors in the transmission control module), the electronics must be protected against a further rise in temperature. When this threshold value is exceeded, the transmission control module initiates a reduction in engine torque to reduce heat input. Up to a temperature of approx. 293°F (145 °C), engine torque can be reduced gradually until the engine is at idle. When the engine is at idle, the clutches are open and there is no power transmission from the engine to the drive wheels. When the protective function is activated, an entry is made in the fault memory and the following text message is displayed in the instrument cluster: “You can continue driving to a limited extent.”Clutch ProtectionIf the clutch cooling oil temperature exceeds a value of approx. 320°F (160 °C), as determined by G509, the clutch is within a critical temperature range that can damage it. These temperatures occur, for example, when accelerating on extreme gradients, when towing a trailer, or when the vehicle is held stationary on an uphill slope using the accelerator and the clutch without engaging the brake. As a safety precaution, engine torque is reduced when cooling oil temperature exceeds 320°F (160 °C.) If the cooling oil temperature continues to rise, engine torque is gradually reduced, sometimes to idle. When the engine is at idle, the clutches are open and there is no power transmission from the engine to the drive wheels. When the protective function is initiated, an entry is made in the fault memory and the following text message is displayed in the instrument cluster: “You can continue driving to a limited extent.” As an additional safety precaution, the clutch temperature is determined using a computer model. If the computed temperature exceeds a pre-defined value, the above mentioned precautions are taken.40 0B5 S Tronic TransmissionAll you need to know about the …… transmission control moduleIn the B8 series, a new data and diagnostic log is used for the engine control modules, the TCM, and the airbag control module. The previous data blocks and numberings are no longer used. Individual measured data is now available and listed as full text in alphabetical order. This required measured data can then be specifically selected.… towingIf a vehicle with S tronic needs towing, the conventional restrictions of automatic transmissions apply: – Selector lever in position “N” – A maximum towing speed of 30 mph (50 km/h) must not be exceeded – A maximum towing distance of 30 mi (50 km) must not be exceeded… clearing the fault memoryThe fault memories of the engine and transmission control module are always cleared jointly. If the fault memory of the transmission control module is cleared, then the fault memory in the engine control module will be cleared as well. The converse applies if the memory of the engine control module is cleared.Explanation:When the engine is at standstill, the oil pump is not driven and certain parts of the transmission are no longer lubricated. Exceeding a speed of 30 mph (50 km/h) results in unacceptably high rotational speeds within the gearbox and dual clutch, because one gear is always engaged in both sub-gearboxes. If these towing cautions are not observed, serious transmission damage can occur.41 0B5 S Tronic Transmission“Limp Home” ProgramsIn the event of a malfunction, serious damage can be prevented and mobility preserved by means of “limp home” programs initiated by the transmission control module. In addition, there are also protective functions, which protect certain components against overload. In the event of certain pre-defined system malfunctions, the transmission control module shuts down the subgearbox in question and activates the relevant “limp home” program (driving with intact sub-gearbox). 1. Driving with sub-gearbox 1, sub-gearbox 2 shut down: – Only gears 1, 3, 5, and 7* can be engaged (with interruption in tractive power) – Backing up (reversing) is not possible 2. Driving with sub-gearbox 2, sub-gearbox 1 shut down: Only gears 2, 4, 6, and R* can be engaged (with interruption in tractive power). 3. Complete gearbox shutdown: In the case of serious faults — for example, a faulty powertrain CAN, no identification by the immobilizer, or recognition of an incorrect ratio in the gear steps or in the final drive — the gearbox is completely shut down.*The nature of the fault dictates which gears are still available. To be sure that components do not overspeed, certain gears are disabled depending on fault type. After ensuring that no gear is engaged in the deactivated gearbox, all gears of the intact subgearbox are shifted without any further restrictions.42 0B5 S Tronic TransmissionDisplays/WarningsThe 0B5 transmission features new information and warning technology in the instrument cluster, which will alert the driver to a system malfunction or the initiation of a protective function. The following warnings are displayed: Gearbox fault: You can continue drivingDisplay 1Display 1 appears when faults the driver may not notice are recognized by the transmission control module, which then activates a suitable substitute signal. These faults result in no, or only negligible, loss of performance. The purpose of the warning is to prompt the driver to take the vehicle to an Audi dealer at the next opportunity.Display 2Display 2 appears when gearbox protection functions and faults result in a loss of performance. This can have the following effects: – “Limp home” program: “Driving with sub-gearbox 2” is active. For example, gearshifts have interruptions in tractive power (even-numbered gears only) – Gearbox protective function is active, but engine power is reduced because the engine torque reduction function is also active – No power transmission to the driving wheels after stopping – The engine can no longer be started Gearbox fault: You can continue driving to a limited extent onlyDisplay 3Display 3 appears when the “limp home” program, “Driving with sub-gearbox 1,” is active because reverse gear cannot be selected at the same time. Text messages disappear after five seconds, and are displayed again for five seconds at “ignition ON.” Yellow warning symbols are permanently displayed. Gearbox fault: You can continue driving to a limited extent only No reverse gear43 Sport DifferentialTraditional quattro DriveSince 1980, quattro has been synonymous with outstanding driving dynamics. In its basic form, the torque-sensing center differential delivers 40% of the tractive force from the engine to the front axle and 60% to the rear axle. This degree of rearward bias is now standard on all newer Audi models because it ensures optimum performance. The torque-sensing differential redistributes engine output without delay if road surface conditions change. The quattro system technology also has distinct advantages in terms of lateral dynamics. By distributing traction among all four wheels, each wheel has greater potential to resist lateral forces, and tire grip is optimized. The action of the electronic differential lock (EDL) and typical Audi settings adopted for the ESP also add to a high level of stability.990193_00144 Sport Differentialquattro Drive with Sport DifferentialThe quattro system with electronically controlled sport differential distributes input torque variably between the two rear wheels, with nearly all tractive force directed to just one wheel, if necessary. Torque input also ensures a neutral road behavior. The sport differential is active not only under load, but also on overrun. Its torque distributing action enhances car agility when the clutch is disengaged. Depending on steering angle, lateral acceleration, yaw angle, road speed, and other signals, the control module calculates the most suitable distribution of torque to the rear wheels for every driving situation. When the steering wheel is turned, for example, or when the car is accelerated in a corner, power is redirected in a controlled manner to the outer rear wheel. This has the effect of “forcing” the car into the corner so that the angle of the front wheels is followed accurately. The difference in tractive force between the left and right wheels also exerts a steering effect, so that the usual corrections by the driver at the steering wheel are no longer needed. Understeer, the tendency for the car to run wide at the front when cornering, is virtually eliminated.990193_002990193_002a45 Sport DifferentialTraditional quattro DriveIn the illustration below, a car adheres to successive bends when driven rapidly along a typical country road, similar to the precise track formed by skis in snow. The sport differential redistributes the power input continually and quickly and counteracts any tendency for the car to understeer or oversteer before either of these effects can build up. For the driver, this means reduced effort at the steering wheel and higher maximum lateral acceleration. When approaching the car’s handling limits, the sport differential acts like ESP, but with the principle reversed. Corrective movements are not initiated solely by altering the engine settings or applying the brakes, but also by controlled redistribution of tractive force through the sport differential. The car’s forward progress becomes distinctly smoother and free-flowing because its actual road dynamics and those sensed subjectively by the driver are enhanced since ESP comes into action much less frequently. Since its reaction time is extremely short — less than 100 milliseconds — the sport differential takes effect even more rapidly than ESP. Furthermore, ESP can only react to a discrepancy between the car’s steering angle and its actual body rotation, whereas the sport differential influences the car’s dynamic behavior before any such discrepancies occur. During sport differential action, ESP is not active. Active torque distribution is based on an entirely new design principle for the rear axle differential. The unit can also divert torque to the outer wheel on the axle, which then rotates faster than the inner wheel when cornering. The rear axle differential has speed modulation units with multi-plate clutches mounted at the left and right sides. The clutches are activated by electro-hydraulic actuators based on input from sensors and other control modules.Steering into a curve: torque is redistributed outward to enhance cornering abilityChanging direction: depending on driving situation, torque is redistributed to enhance agility and/or stabilityAccelerating out of a curve: torque is redistributed outward to avoid accelerationinduced understeer990193_00346 Sport DifferentialAudi Drive Select with Sport DifferentialThe quattro driveline with sport differential is also part of Audi drive select, which integrates key components that affect each driving experience. These components include the engine, transmission, steering, shock absorbers, and sport differential. Drivers can adjust the characteristics of these systems at any time to suit their personal preferences. Buttons on the center console enable drivers to vary the operation of Audi drive select in three stages ranging from comfortable to sport mode, or to create a profile that suits their personal preferences. The engine’s throttle response characteristic can be determined first, followed by that of the servotronic speed dependent power steering and, if the car has automatic transmission, its shift points. The functions of the sport differential can also be varied to suit the driver’s wishes. In “comfort” mode, driving safety and vehicle stability have absolute priority, with optimal damping of load reversals. In “auto” mode, a balance is achieved between all of the functions. The “dynamic” mode ensures optimum vehicle agility during load reversals.990193_00447 Sport DifferentialComponent OverviewBreather for the main differential Breather for the right speed modulation unit Right speed modulation unitBreather for the left speed modulation unitLeft speed modulation unit990193_005Hydraulic pump990193_006 Hydraulic control moduleSpecifications Service Designations: Development: Manufacturer: Torque Capacity: Speed Modulation Unit Ratio: Weight: Final drive 0BF, internal: HL601 Magna powertrain (Graz, Austria) — Audi AG Magna powertrain Up to approx. 480 lb ft (650 Nm) engine torque itot 1.095 Approx. 95.9 lb (43.5 kg) including oil48 Sport DifferentialThe sport differential has a conventional pinion shaft and ring gear. Attached at both sides of the differential are speed modulation units. These units are made up of two sun gears and two ring gears and are sometimes referred to as speed modulation gearboxes or super-position gearboxes. They provide a step-up (or step-down) transmission ratio for each axle depending on the driving situation.The engagement of the speed modulation units is done electro-hydraulically. Pressure is developed by an electric motor-driven hydraulic pump and directed to the multi-plate clutches by a hydraulic control module. Clutch actuation is determined by All Wheel Drive Control Module J492. This ability to change the ratio (dependent on driving situation) is also referred to as “torque vectoring.”Left speed modulation unitRight speed modulation unitPinion shaftMulti-plate clutchMulti-plate clutchRing gear990193_00849 Sport DifferentialSpeed Modulation Gearbox Component OverviewDifferential pinion shaftDifferentialClutch pistonMulti-plate clutchRing gear 1Ring gear 2Sun gear 2Sun gear 1Double shaft sealDifferential side gearsDifferential ring gear990193_00950 Sport DifferentialSun gear 1 is integral with the differential housing and, therefore, turns at the same speed. Sun gear 1 is internally meshed with ring gear 1 which rotates at a ratio of 0.868.Sectional View A - ASun gear 2 is integral with the stub axle. When a multiplate clutch is engaged, ring gear 2 is joined to ring gear 1. Ring gear 2 then drives sun gear 2 which in turn drives the stub axle. Combining the gear ratios of both sun gears and ring gears provides the final output ratio to the stub axle.i1 = 0.868Z = number of teeth per gear i = gear ratioSun gear 1, Z1 = 33 990193_010 Ring gear 1, Z2 = 38AB Sun gear 2Sun gear 1Ring gear 1 990193_012Multi-plate clutchRing gear 2 A Sectional View B - BB i2 = 1.261Ring gear 2, Z3 =29 990193_011 Sun gear 2, Z4 =23itot = i1 x i2 = 0.868 x 1.261 = 1.095 51 Sport DifferentialPower Flow Without InterventionThe sport differential functions as a normal open differential when the multi-plate clutches of the speed modulation boxes are not engaged. Torque is transmitted from the pinion shaft to the ring gear. The differential transfers the torque to the axles via the side gears.Differential pinion shaftSide Differential gears ring gear990193_014a52 Sport DifferentialPower Flow With InterventionThe differential ring gear drives sun gear 1 which in turn drives ring gear 1. With clutch activation, ring gear 1 and ring gear 2 are joined together. Ring gear 2 drives sun gear 2 which drives the stub axle. Only one speed modulation gearbox can be engaged at a time. When activated, the clutches do not fully engage, as there is always a defined amount of slip between the plates. This slip is monitored by All Wheel Drive Control Module J492 and has important service implications.Differential pinion shaftDifferential ring gearSun gear 2 Ring gear 2 Sun gear 1 Ring gear 1990193_015a53 Sport DifferentialOil CircuitsThe sport differential has two oil circuits and three distinct oil chambers. The differential pinion and ring gear (conventional differential components) have a separate oil chamber filled with hypoid oil. Two speed modulation gearboxes each have their own oil chamber and are interconnected by an oil passage. This forms a common oil circuit, which is filled with a special ATF. Both fluids are lifetime fills.Hypoid oil ATF990193_01654 Sport DifferentialA ball valve integrated in the oil circuit prevents the ATF oil circuits from overflowing to one side during transverse acceleration.990193_031ATF filler and inspection plugNo transverse acceleration 990193_017 ATF drain plugHigh transverse acceleration990193_017a55 Sport DifferentialOil Circuit SeparationA double shaft seal and a special oil seal (rectangular ring) on each side ensures that the hypoid oil and ATF circuits are safely separated from each other.990193_005Oil drain port, left sideOil seal Double shaft seal990193_01856 Sport DifferentialOil drain ports prevent the mixing of ATF and gear oil if a seal should fail. If a failure occurs, oil is vented to the outside of the axle housing via the drain port.990193_019Double shaft seal Oil drain port, right sideOil seal990193_02057 Sport DifferentialOil Inspection and Drain PlugsATF filler and inspection plugSymbol for ATFATF drain plug990193_006 Hypoid oil drain plugSymbol for final driveAxle oil filler and inspection plug990193_002a990193_02158 Sport DifferentialHydraulic ControlPipe to left clutchOil Pressure/ Temperature Sensor G437 Oil Pressure/ Temperature Sensor 2 G640All Wheel-Drive Pump V415All Wheel Drive Clutch Valve N445990193_006 All Wheel Drive Clutch Valve 2 N446Shuttle valves V415 Hydraulic pumpG437 Seal with Screen Check valvesG640N446N445 990193_02259 Sport DifferentialBasic ConfigurationPressure for hydraulic operation is supplied by a pump driven by All Wheel Drive Pump V415. The pump operates in both directions dependent upon which clutch is to be activated. The pressure limiting valves are designed to limit the extent of coupling force applied to the clutches to approx. 885 lb ft (1200 Nm). The shuttle valves move to prevent hydraulic pressure from being applied to both clutches at the same time. Both the oil pressure and temperature sensors measure the same hydraulic pressure. However, they measure the pressure opposite from each other during clutch application. One will display a rising pressure while the other displays a falling pressure. This is done as a diagnostic function and plausibility check by All Wheel Drive Control Module J492. All Wheel Drive Clutch Valve N445 and All Wheel Drive Clutch Valve 2 N446 are open until current is supplied.Pressure limiting valvesOil Pressure/ Temperature Sensor 2 G640Left clutch Shuttle valves Oil Pressure/ Temperature Sensor G437Right clutchAll Wheel Drive Clutch Valve N445Hydraulic pumpAll Wheel Drive Clutch Valve 2 N446Check valveCheck valveMAll Wheel Drive Pump V415990193_02360 Sport DifferentialActivation of Right ClutchThe right clutch of the sport differential is activated, for example, when the vehicle is taking a curve to the left. All Wheel Drive Pump V415 drives the hydraulic pump which suctions ATF from the sump through one check valve and All Wheel Drive Clutch Valve N445. Current is applied to close All Wheel Drive Clutch Valve N446 2 and pressure rises in the system. The shuttle valves move to block oil pressure from being applied to the left clutch. Oil Pressure/Temperature Sensor G437 measures the pressure and displays it as a rising pressure. Oil Pressure/Temperature Sensor 2 G640 measures the same pressure but displays it as a declining pressure. The hydraulic pressure developed applies the right clutch via its actuating piston.Pressure limiting valvesOil Pressure/ Temperature Sensor 2 G640Left clutch Shuttle valves Oil Pressure/ Temperature Sensor G437Right clutchAll Wheel Drive Clutch Valve N445Hydraulic pumpAll Wheel Drive Clutch Valve 2 N446Check valveCheck valveMAll Wheel Drive Pump V415990193_02461 Sport DifferentialActivation of Left ClutchThe left clutch of the sport differential is activated, for example, when the vehicle is taking a curve to the right. All Wheel Drive Pump V415 drives the hydraulic pump in the opposite direction as before. This suctions ATF from the sump through one check valve and All Wheel Drive Clutch Valve 2 N446. Current is applied to close All Wheel Drive Clutch Valve N445 and pressure rises in th