TECHNICAL DOCUMENTATION
SSP 323 Audi A6 ‘05

This PDF is currently unavailable.
Read document text
Service TrainingAudi A6´05Self-Study Programme 323PrefaceThe new Audi A6 – the most progressive vehicle takes the leadDesign and performance are the main driving elements on its way to the top position. Furthermore, the new Audi A6 embodies the consequent continuation of the familiar Audi brand values, sports appeal, progressiveness and intrinsic quality, which are evident in the fourth generation of this sporty business limousine.”Vorsprung durch Technik” – this guiding principle is consistently maintained in the new Audi A6´05 through its innovative technologies. Highly dynamic chassis technologies are combined with consumption-optimized drives with the latest FSI or TDI technology for greater driving pleasure. Rounded off with servotronic and the 6-stage tiptronic system with sport programme, the new Audi A6´05 has optimal driving dynamics as well a sporty and comfortable tune-up.The MMI operating system in the interior of the vehicle is the central control for the extensive functionalities. The driver-orientated cockpit design provides a perfect workplace, which is both stylish and sophisticated. The high functionality is emphasized by the customer-orientated features in the safety and convenience function areas.Self-study programmes for the Audi A6´05SSP 323 Audi A6´05 – – – – Introduction to the vehicle Body technology Passenger protection Air conditioningOrder No.: A04.5S00.06.20323_057SSP 324 Audi A6´05 Chassis – – – – – Front axle technology Rear axle technology Steering system ESP Electromechanical parking brake EPBOrder No.: A04.5S00.07.20323_058SSP 325 Audi A6 ´05 Engines and Gears – – – – – 3.0 V6 TDI Common Rail 3.2 litre V6 FSI Manual gearbox 01X, 02X, 0A3 6-stage automatic transmission 09L Multitronic 01JOrder No.: A04.5S00.08.20323_059SSP 326 Audi A6 ´05 Electrics – – – – Networking Bus topologies Convenience electrics InfotainmentOrder No.: A04.5S00.09.20323_056The Self-Study Programme provides information on the fundamentals of the design and function of new vehicle models, new vehicle components or new technologies. The Self-Study Programme is not a Workshop Manual! Specified values serve only to make the information easier to understand and relate to the software version that was valid at the time the Self-Study Programme (SSP) was created. For maintenance and repair work, please make sure to use the current technical documentation.ReferenceNoteContentsChapter 1 IntroductionProduct highlights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Chapter 3 Passenger protectionSafety system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Airbag control unit J234 . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data exchange. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Belt warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Airbag disabling key switch, front passenger side E224 Seat belts and belt tensioners N153 and N154 . . . . . . . . Active head restraints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Battery cut-off relay J655 . . . . . . . . . . . . . . . . . . . . . . . . . . . Seat occupied recognition, not for USA . . . . . . . . . . . . . . . Seat occupied recognition for USA market . . . . . . . . . . . . Seat occupied recognition control unit J706 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 . 22 . 23 . 24 . 26 . 27 . 31 . 31 . 33 . 34 . 36 . 37 . 40Chapter 5 Engine / GearboxOverview of available engine / gearbox combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Chapter 7 ElectricsBus topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 In/outputs on control units J393, J519 and J520 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56ContentsChaper 2 BodyBody shell / connection technology Materials . . . . . . . . . . . . . . . . . . . . . . . . Blanks . . . . . . . . . . . . . . . . . . . . . . . . . . Assemblies . . . . . . . . . . . . . . . . . . . . . . Bumpers . . . . . . . . . . . . . . . . . . . . . . . . Trailer coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..8 . 10 . 12 . 14 . 16 . 17Chapter 4 DiagnosisVAS 5053 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VAS 5051 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VAS 5053/20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recording the working time using the VAS 5051 / 5052 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 . 43 . 44 . 45Chapter 6 ChassisOverview . . . . . . . . . . . . . . . . . . . . . . . Front axle . . . . . . . . . . . . . . . . . . . . . . Rear axle . . . . . . . . . . . . . . . . . . . . . . . Wheel brake . . . . . . . . . . . . . . . . . . . . ESP . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electromechanical parking brake – Steering system. . . . . . . . . . . . . . . . . Wheels / tires . . . . . . . . . . . . . . . . . . . Tire pressure control system . . . . . .... .... .... .... .... EPB .... .... .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 . 48 . 49 . 50 . 51 . 51 . 52 . 53 . 53Chapter 8 Air conditioningOverview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Convenience automatic air conditioning and convenience automatic air conditioning plus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 CAN networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Components in the Audi A6 ´05 air conditioning unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Replacing components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Control motor versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 In/output signals at Climatronic control unit J255 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Additional electric air heater. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Auxiliary / additional heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Air conditioning diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Special tools for the Audi A6´05 air conditioning system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75IntroductionProduct highlightsThe product features which support the new Audi A6´05 on its way to the top, can be summarised as follows: One wing is the design, the other wing is the car’s performance.PerformancePower trains – Power-controlled power trains, better than competition – New FSI technology from motor racing – New TDI technology common rail II with Piezo injectors – Quattro: – Multitronic – 6-stage Tiptronic – Wide selection of motors and gearboxesDesignQuality – Use of intrinsically valuable materials (aluminium, wood, leather) – High-quality standard equipment (light-rain sensor, aluminium trim, active headrests in front, servotronic, EPB, fog headlights, ...) – Highest safety standards (5 star Euro NCAP) – Small gap widths, even jointsPackage Innovation – – – – – – – FSI Common rail II with piezo injectors Expanded ESP MMI as standard Integrated driver cockpit Electromechanical parking brake Advanced key, adaptive light, LED brake lights, comfort climate control plus – Premium vehicle dimensioning – Rear knee room 8 cm – Wider shoulder widths, front +23 mm, rear +6 mm – Front headroom +7 mm – Superior luggage compartment volume (546 l) for front-wheel and quattro models – Wheelbase +9 cmExterior/Interior Driving dynamics – New dynamic chassis with trapezoidal-link rear axle and redesigned four-link front axle – Increased body stiffness + 35 % – Larger tyre diameter – Servotronic now standard – Wider tread widths, front +7 cm, rear +6 cm – Excellent rear downforce for safe handling – Completely new line design (roofline, shoulder line, dynamic line) – Dynamic joint matching – Coupe-like shape – Separation edge on rear end – Single frame – Double-pipe exhaust for front-wheel and quattro models – Full exterior surface paintedPerformance Driving dynamics Innovation The most progressive car takes the lead Quality Package Design323_038Power trainsExterior/Interior6DimensionsThe new Audi A6´05 impresses with its imposing external dimensions. The vehicle length has been increased to 4.92 m, which corresponds to an increase of 12 cm compared to its predecessor. The vehicle width has been increased by 4.5 cm to 1.86 m. The height of the new A6´05 has been increased by 0.8 cm to 1.46 m. The new Audi A6´05 has grown. For the dimensions, please refer to the diagrams.323_0347BodyBody shell / connection technologyThe main objectives during the development of the new Audi A6 body design were the realization of high passive safety characteristics and improved rigidity values as a precondition for optimizing vibration damping characteristics. In spite of the greater demands compared with the previous model, the body weight has been kept at the same level.323_001A further task during the body development process is to minimize the number of necessary body versions. The new A6´05 uses four body shell versions: – rigid rear panel – with opening for loading – without sliding sunroof – with sliding sunroof A standard rear section is used for the front-wheel drive and quattro vehicles.8In addition to classic resistance spot welding, the following connecting techniques are used on the new A6´05 body shell: – Spot welding bonding – Punch riveting – Clinching (bonnet & rear opening hood) – Laser soldering – Laser welding – as well as MIG solderingSpot welding bonding, using a high-strength structural adhesive, is used for particularly crash-relevant and rigidity determining connections (length of the bonded seam factor 3 compared with predecessor).The Aluminium components are joined to the galvanized steel sheets by means of punch rivets and by bonding.These aluminium-steel connections are used on the following parts in the body: – in the plenum chamber front panel – sill reinforcement (with aluminium extruded section) – rigid rear panel with rear shelfSpot welding bonding Laser MIG soldering323_002Laser-soldered zero jointThe roof and side panel frame are joined by laser-soldering. Poorly accessible components are joined by laser-welding. The laser-welding head is smaller and thus has greater flexibility than comparable spot welding tongs. In addition, the weight can be reduced by reducing the flange widths. MIG soldering is used for closed sectional bars which are only accessible from one side, e.g. longitudinal floor members.Roof Outer side part323_0039BodyMaterialsIn addition to conventional deep-drawing steels, the following materials are used in the body structure of the new Audi A6´05: – High tensile sheet steel – Special sheet steel – Aluminium sheets – Aluminium extruded sections and – Plastic-ribbed deep-drawing steel component (hybrid component)High tensile steels (180 - 300 N/mm²) Dual-phase steels (340 - 500 N/mm²) Weight percentage of high-tensile steel sheets Total: 45 % Upper section: 42.3 % Lower section: 46.7 % Special steel (600 - 900 N/mm²) Aluminium Hybrid component10High-tensile steel sheets are used especially in areas which require strengthening and greater impact resistance. Special steel sheets are also used in the body structure, e.g. front wheelhouse cross-member. The engine bonnet and front mudguards are made of aluminium. In addition to the add-on parts in the shell, aluminium sheets are used in the structure for large-area components which are not subject to excessive stress.Large-volume aluminium extruded sections are used as sill reinforcements to stiffen the cell structure in the event of an offset or side crash. The front roof frame is designed as a hybrid component in order to reduce the weight.323_00411BodyBlanksBlanks with different wall thicknesses and material qualities are used to realize a stress-adapted material distribution for large-area components which are subject to high stress. Laser-welded blanks, so-called tailored-blanks, are used for – the front suspension strut cross member – front floor panels – inner side section – rear longitudinal member – and door inner panelstailored blanks tailored-rolled-blanks hybrid components12Tailored-rolled blanks, which have variable rolled wall thicknesses, have particular advantages. They can be used to produce continuous material thickness transitions which meet the local stress conditions. This technique is used to optimize the front longitudinal member structure.In total, a weight reduction of 8 kg (without add-on parts) was realized through the material selection being adapted to the respective stress conditions. An additional weight reduction of 9 kg was realized by using blanks with different wall thicknesses.323_00513BodyAssembliesPlenum chamberOne application area for special steel is the chassis connection in the proximity of the spring and shock absorber seat. It was possible to reduce the wall thickness of the respective parts from 2.5 to 1.4 mm. The resulting loss of local rigidity was offset by creating an optimized profile. In addition, a tailored blank is fitted in the plenum chamber. This ensures the highest possible energy absorption in the event of a crash. At the same time, the necessary rigidity and stability are ensured during normal driving. Transverse rigidity is ensured by a rolled sectional bar as an additional reinforcement.Special steel (600 - 900 N/mm²) tailored blanks Aluminium323_031WheelhouseTo ensure an optimum introduction of the crash energy from the front of the car into the passenger compartment, special steel components were used in the proximity of the wheelhouse.323_03014B-pillarDue to the increased requirements regarding the strength of the B-pillar, a combination of different materials is used. – front inner side section (high tensile steels) – rear inner side section, tailored blank (dual-phase steels, high tensile steels) t = 1.35 mm and 0.8 mm – B-pillar reinforcement (dual-phase steels) – B-pillar (dual-phase steels)323_03215BodyBumpersFront bumperThe bumper on the new Audi A6´05 is painted in the colour of the car. It comprises the following components: – Coating – Top cover – Towing lug cover – Radiator grille with chrome frame – Fog lamps – Side air inlet grilles – Bumper support The number plate in the radiator grille is integrated stylishly and harmoniously within the overall design.323_006The bumper support comprises an open aluminium cross member, which is screwed on to the longitudinal member using newly developed shear boxes. The shear box absorbs the crash energy from all centrical and slightly diagonal impacts through its shearing effect. Expensive damage to the welded vehicle structure behind it is thus avoided up to a speed of 15 km/h. In the event of diagonal impacts, the impact energy is absorbed by the bumper buckling (folding) and deforming. The seat for the towing lug is integrated in the right-hand shear box. The towing forces are guided centrically into the longitudinal member.323_00816Rear bumperThe rear bumper assembly comprises the coating, spoiler, towing lug cover and closing part components. It is mounted on the vehicle by means of fixed guides on the body. The bumper support and the bracket for the bumper support are made of aluminium and are produced by extrusion moulding. Compared to the previous model, the joints on the A6´05 have been noticeably reduced. Due to a special adjusting/holding part below the rear light, the zero joint between the bumper coating and side part has been reduced to 0.8 mm. A parking aid and a mechanically swivelling trailer coupling are available (optional).323_007Trailer couplingThe newly developed trailer coupling fitted in the A6´05 is equipped with a mechanically swivelling ball rod. The ball rod swivels around a rotation axis, which is angled at 45° to the longitudinal axis of the vehicle. The swivel angle between the swivelled-out towing position and the idle position behind the bumper is 180°. The system is unlocked by means of a handwheel located in the boot.323_010323_00917BodyControl unit for trailer detection J345Arrangement in the vehicle The basic function of trailer detector control unit J345 corresponds to the control unit which has already been in use since the 2001 Audi A4. To be used in the Audi A6´05, it was upgraded by the control function for the swivelling trailer coupling. It now has the additional task of detecting the locking status of the mechanically swivelling trailer coupling and indicating this to the driver.F354 HandwheelK226 K227F355323_03518On pulling the handwheel in the boot, the contact switch on handwheel F354 is closed. On turning the handwheel, the locking bolt on the trailer coupling is unlocked mechanically by a Bowden cable and the contact switch on locking bolt F355 opens. After being unlocked, the trailer coupling can be swivelled out/in mechanically. After being swivelled, it is automatically locked by spring power. The contact switches return to their initial position. The control unit cannot differentiate between a locked, swivelled-in trailer coupling and a locked, swivelled-out trailer coupling. The locking state is indicated by two LEDs in the handwheel for the trailer coupling. When the green warning lamp for trailer coupling locked (K226) lights up continuously, it indicates that the trailer coupling is swivelled in/out correctly.323_036The red warning lamp for trailer coupling unlocked (K227) flashes when the trailer coupling is not locked. In addition, a message appears on the central display in dash panel insert J285. When terminal 15 is switched off, the warning lamp for trailer coupling locked (K226) switches off if the tailgate/boot lid is closed or remains open for longer than 10 minutes. The warning lamp for trailer coupling unlocked (K227) switches off if the tailgate/ boot lid is closed or remains open for longer than 20 minutes. The respective warning lamp switches on again when there is a control unit wake-up or a CAN wake-up.CHECK TRAILER COUPLING323_03319Passenger protectionSafety systemA top-level safety system: The performance target is to increase the existing high safety level of the current Audi fleet. The compliance with current laws and the completion User tests, in which the new Audi A6´05 was to gain a top position in the rating scheme, were only a part of the extensive safety requirements. In many cases, additional Audi in-house requirements increase the requirements which have to be met by the development team. Particular attention was paid to a high protection potential in the event of an accident and the compatibility. Audis's policy of designing vehicles with high safety specifications is supplemented by scientifically gained knowledge of the actual accident and its effects. For this, the AARU (Audi Accident Research Unit*) examines crashes involving relatively new Audi vehicles. The development team's task is to analyse and reconstruct accidents and to draw up potential improvements. In addition to this, the AARU evaluates the relevant accident databases. The safety system in the Audi A6´05 comprises the following familiar components: – – – – – – Airbag control unit Driver and front passenger airbags, two-stage Front side airbags Sideguards (head airbags) Sensors for side crash detection Front belt tensionersThe Audi A6´05 has the following new components: – Crash sensors for the front airbag, the so-called upfront sensors for frontal crash detection – Battery cut-off relay – Sensors for side crash detection in the doors – Switches in the front belt locks – Seat occupied recognition in the front passenger seatThe vehicle can be equipped with side airbags at the rear and a key switch for deactivating the front passenger airbag with a corresponding warning lamp (optional). The safety system in the Audi A6´05 is rounded off by the active head restraints in the front seats. The A6´05 thus constitutes a successful example of an overall vehicle development aimed at protecting the passengers. Due to the different demands and legal provisions which car makers are subject to in the different markets, the equipment can vary for the US American market in particular. * Audi Accident Research UnitNote Observe the respective safety instructions in the repair guide before carrying out any work on the airbag system!Legend E224 E24 E25 G128 G179 G180 G256 G257 G283 G284 Airbag disabling key switch, front passenger side Belt switch, driver side Belt switch, front passenger side Seat occupied sensor, front passenger side Crash sensor for side airbag, driver side (front door) Crash sensor for side airbag, front passenger side (front door) Crash sensor for side airbag, rear, driver side Crash sensor for side airbag, rear, front passenger side Crash sensor for front airbag, driver side Crash sensor for front airbag, front passenger side20G283G284K145 J623 J285 K75 / K19PASSENGER AIRBAG OFFAIRBAGE224AUS EINT16 J533N95 / N250N131 / N132G179J234G180N199E24E25G128N200N251 N153 N154N252G256G257J393J655326_002J234 J285 J393 J533 J623 J655 K19 K75 K145Airbag control unit Control unit in dash panel insert Central control unit for convenience system Data bus diagnosis interface Engine control unit Battery cut-off relay Warning lamp for belt warning Airbag warning lamp Airbag warning lamp, front passenger side, off (PASSENGER AIRBAG OFF)N95 N250 N131 N132 N153 N154 N199 N200 N251 N252 T16Airbag igniter, driver side Airbag igniter 2, driver side Airbag igniter 1, front passenger side Airbag igniter 2, front passenger side Belt tensioner igniter 1, driver side Belt tensioner igniter 1, front passenger side Side airbag igniter, driver side Side airbag igniter, front passenger side Head airbag igniter, driver side Head airbag igniter, front passenger side Plug-in connection, 16x (diagnosis connection)21Passenger protectionAirbag control unit J234The task of the airbag electronics is to detect vehicle deceleration and evaluate it so that a collision is reliably detected. The control unit can detect frontal, side and tail accidents. In addition, the electronics also have the task of activating the respective restraint systems (airbags / belt tensioners) depending on the type of collision and its severity and activating the Crash output. In addition to the internal sensors in the control unit, the external crash sensors are also used to detect vehicle deceleration during impact. The electronics can only decide when and which safety components to activate after all the sensor information has been evaluated by the control unit electronics. If an airbag control unit is replaced, then it must be coded and adapted to the respective. These functions can only be peformed by means of the guided fault finding procedure and a diagnosis tester which can be used online. The Service technician needs access (with password) to the ”FAZIT” database at Audi. If the coding or adaptation is not carried out in the correct manner, malfunctions can occur in other vehicle systems such as the ESP, for example.The airbag electronics have the following main tasks: – Crash detection (front, side, tail) – Defined triggering of the airbags, belt tensioners and battery cut-off – Defined triggering of the second front airbag stage – Evaluation of all input information – Permanent monitoring of the entire airbag system – Independent power supply via capacitor for a defined time (approx. 150 ms) – Error indication via failure warning lamp – Storage of error and crash information – Notification of a crash event to other system components via drive CAN or discrete Crash output (conventional cabling) – Activate belt warning326_00822Airbag warning lamp K75The airbag warning lamp, which is located in dash panel insert J285, is triggered via the bus CAN. If there is no data message from the airbag control unit, the warning lamp is automatically switched on from the dash panel insert.Rear crash detectionIn the event of a rear-end crash, the airbag control unit evaluates the information from the internal crash sensor and the crash sensors for front airbags G283 and G284. If their signals exceed a fixed value, the belt tensioners are ignited and the battery cut-off relay is activated.Data exchangeThe airbag control unit is integrated within the drive CAN.The airbag control unit transmits the following information on the drive CAN: – – – – – – – Trigger warning lamp K75 Activate belt warning Diagnosis data Crash signal Crash information for the actuator test ESP data Front passenger airbag disabled (for USA only)The airbag control unit evaluates the following information from the data bus: – Dimming of the airbag warning light Passenger airbag off23Passenger protectionSensorsCrash sensor(in the control unit) The acceleration sensors are arranged in such a way that both deceleration in the vehicle's longitudinal axis (x-axis) and deceleration in the vehicle's transverse axis (y-axis) are detected.Safety switch(in the control unit) The mechanical safing sensor in the airbag control unit for the Audi A6‘05 has been replaced by a micromechanical acceleration sensor. This sensor also detects the vehicle's deceleration in the direction of travel (x-axis) and sends this information to the control unit electronics for a plausibility check.326_015326_016Crash sensors for front airbag G283 and G284(upfront sensors at front end) The severity of the crash changes the signal, which the front airbag crash sensor sends to the airbag control unit. Depending on the signal, a threshold reduction is activated in the airbag control unit, which improves the crash detection function and and thus enables the airbags to be ignited earlier. A greater protective effect can be attained by triggering the airbags earlier.Front airbag crash sensors326_009Crash sensors for side airbag G179 and G180(in the front doors) Pressure sensors are now used in both front doors (new). The deformation of the vehicle in the event of a side crash causes a short-term increase in air pressure in the door. This pressure increase is detected by the sensor and is forwarded to the airbag control unit.Front airbag crash sensors 326_00724Crash sensors for side airbag, rear, G256 and G257(C-pillar) Both crash sensors for side airbag G256 and G257, which are fitted near the C-pillar (left and right), are conventional acceleration sensors, which were already used for the previous Audi A6 model.How the crash sensors work A crash sensor essentially comprises a housing, evaluation electronics and a micro-mechanical acceleration sensor. Basically, the acceleration sensor is structured like a capacitor. Some of the capacitor plates are fixed. The counterparts of these are movable and work like a seismic mass. If the seismic mass is pushed into recording direction during an accident, the capacity of the capacitor changes. This information is evaluated by the evaluation electronics and is then digitally processed and transmitted to the airbag control unit. Pressure sensors, on the other hand, react to a change in pressure conditions. The resistance of the micromechanical sensor unit is monitored and evaluated.Evaluation electronicsAcceleration sensor326_003 Idle position Movable capacitor plate Crash Direction of detectionCapacitor plate fixedEvaluation electronics326_02525Passenger protectionBelt warningThe new Audi A6´05 includes a belt warning function for both driver and passenger. After switching on the ignition, the driver's belt lock switch and the front passenger's belt lock switch (in conjunction) with the seat occupation sensor on the front passenger side is evaluated by the airbag control unit. The control unit recognizes whether the front passenger seat is occupied on the basis of the resistance values from the seat occupied sensor. If the driver or front passenger has not fastened the seat belt, a warning is given by means of belt warning warning lamp K19 in the dash panel insert and an acoustic signal.Time diagrams for the belt warning Optical and acoustic signals - delayed belt fastened operationTerminal 15 belt fastened belt not fastened Fasten seat beltv 10 km/hWarning lamp for belt warning Acoustic signal t326_029Optical and acoustic signals - belt not fastened operationTerminal 15v 10 km/hFasten seat beltWarning lamp for belt warning at least 90 sec Acoustic signal tThe warning is reactivated if the belt status is changed during ”Tm. 15 on”.326_03026AirbagDriver airbag N95 and N250A two-stage gas generator is used as the driver's airbag. The radial opening of the airbag and the delayed ignition of the propelling charges reduce the loads acting on the driver when the car crashes. Depending on the seriousness and type of accident, the time lapse between the two ignitions can be approx. 5 ms to 50 ms. The radial opening and stepped actuation of the front airbag is particularly advantageous when there is no sufficient clearance between the steering wheel and the upper part of the body. In general, both propelling charges are always ignited. This prevents one propelling charge remaining active after the airbag has been actuated. The gas generator in the driver's airbag is bedded in a rubber ring and swings. This minimizes any vibrations at the steering wheel, as the gas generator acts as a vibration damper.282_07027Passenger protectionFront passenger airbag N131 and N132Like the driver airbag, the passenger airbag also comes with a two-stage gas generator. In contrast to the driver's airbag, the gas generator in the front passenger airbag operates according to the hybrid gas technique. The gas generator comprises two pyrotechnical propelling charges and a compressed gas bottle. The airbag control unit ignites the first propelling charge. The pressure which is produced accelerates a piston, which opens the gas cylinder. The escaping gas inflates and fills the airbag. The ignition of the second propelling charge supplies the airbag with an additional volume of gas.Igniter I, N131Propelling charge IPistonSealing membraneGas ducts to airbag326_004 Igniter II, N132 Propelling charge II Gas cylinder Gas: Argon approx. 94 % Helium approx. 6 % Pressure: approx. 220 bar28Propelling charge I is ignited326_021Propelling charge I burns offPiston opens the gas cylinderGas mixesGas fills the airbag 326_022Propelling charge II is ignited and burns off 326_02329Passenger protectionSide airbags N199 and N200The side airbags have the same design and function as those fitted in other Audi models. However, they have been adapted to the new Audi A6‘05. Vehicles for the North American market are equipped with side airbags (front), which are adapted to meet the specific market requirements.326_039 Side airbag RDW Side airbag NAR326_040Head airbags N251 and N252Sideguards The policy for the sideguard, like all Audi vehicles, is to cover the entire side window area. New head airbags are used in the Audi A6´05. The hybrid gas generator is no longer fitted in the proximity C-pillar, but in the upper area of the B-pillar. The centric location of the gas generator ensures an even filling of the airbag. In addition, the so-called gas lance is no longer required. As a result, not only has the total weight been reduced by approx. 50 per cent, but installation space has also been created for adjacent components.Gas generator326_01730Key switch for disabling airbag, front passenger side E224A key switch as shown in the adjacent block diagram is used to deactivate the front passenger airbag. Deactivation of the front passenger airbag is indicated by the airbag warning lamp, front passenger side, off (K145) (PASSENGER AIRBAG OFF) lighting up. The layout of the four resistors, of which two are always connected in series, ensures correct detection of the switch position. If a faulty key switch is detected by the Diagnosis, an entry is made in the fault memory. This is also indicated by a flashing airbag, front passenger side, off warning lamp.R3 R1R4R2326_001Seat belts and belt tensioners N153 and N154The proven compact tensioners are used for the front seats in the Audi A6. The electrically triggered tensioner units operate according to the ”ball and gearwheel” principle. The belt tensioner units are triggered before the front airbags. To prevent passengers from being subjected to excessive loads, the automatic belt systems are equipped with a belt force limiter. At a certain load level, the force limiter gives and makes the belt longer, thus permitting the passenger to sink into the airbag, which has already opened. In the event of a side crash with side airbag actuation, the corresponding belt tensioner is also triggered.31Passenger protectionBelt switches E24 and E25(in the belt locks) A belt lock interrogation procedure is planned for the driver / front passenger belt lock. The switch position can be determined by means of a resistance measurement. The measured resistance value tells the airbag control unit whether the safety belt has been fastened.326_049Belt switch, belt not fastenedBelt switch, belt fastenedBelt switchBelt switch326_057326_05432Active headrestsActive headrests are used on the front seats in the Audi A6’05. With this system, the headrests move forward in the event of a rear-impact collision in order to reduce the distance between the head and the headrest. Reducing the relative acceleration between shoulder and head significantly reduces the risk of whiplash injuries. A blocking of the mechanics in the event of a frontal impact, as in the case of the Audi A8‘03, is not necessary, due to the lower mass of the head restraints. During a rear-impact collision, the passenger is pressed against the backrest. This force is transferred via the backrest padding to the lumbar support plate in the backrest. The lumbar support plate is linked to the ”Active headrest” function unit in the backrest head via a lever mechanism. If the lumbar support plate moves backwards, the head restraint automatically moves forwards.Functional unit ”Active head restraint”Lumbar support plate326_024Functional unit ”Active head restraint”Lever mechanismLumbar support plateIdle position326_012Activated326_01333Passenger protectionBattery cut-off relay J655The Audi A6‘05, like the Audi A8‘03, will also be equipped with the battery cut-off function in the event of a crash. The battery cut-off relay disconnects the starter and generator lines from the vehicle's battery (located in the boot) in the event of a crash. This avoids short-circuits, which could result in the vehicle catching fire. On being triggered by the airbag control unit, a white field is visible in the element viewing window instead of a copper coil. The airbag control unit monitors the diagnosis process and stores faults which have occurred. The battery cut-off relay is activated every time an airbag is triggered and upon detection of a rear-end crash. A battery cut-off relay which has triggered must always be replaced. The electric battery cut-off relay will be replaced by a pyrotechnic one in the middle of 2004.326_0103430 155 43 1A+J655-B231326_018Pin ATerminal 30Input / output input (screw-type terminal) output (screw-type terminal) input (clamp-type terminal) input (clamp-type terminal) input (clamp-type terminal) Input and output (clamp-type terminal) output (screw-type terminal)Description Battery +B87Output and starter115Switched +231Chassis ground3Crash signalActivation from airbag control unit J234 Diagnosis line from airbag control unit J234 Output to power management control unit J6444Diagnosis53035Passenger protectionSeat occupied recognition, not for USASeat occupied sensor, front passenger side, G128 is a plastic foil, which covers the rear part of the front passenger seat. It consists of several individual pressure sensors. This ensures that the relevant part of the seat is sensed. The seat occupied sensor, front passenger side, reacts to pressure and changes its resistance, depending on the load. If seat occupied sensor, front passenger side, G128 is subjected to a load greater than approx. 5 kg, the airbag control unit detects ”Seat occupied”. As long as the front passenger seat is unoccupied, the seat occupied sensor has a high resistance. If the seat is occupied, the resistance drops. If the resistance exceeds 480 ohms, the airbag control unit detects an interruption and sets a fault in the fault memory. The airbag control unit uses the information from the seat occupied sensor and the belt lock switch for the wearing belt detector.SensorSeat cushions326_035Resistance of G128 Approx. 430 - 480 ohm At 120 ohms and less Above 480 ohmEvaluation Seat not occupied Seat occupied Error, interruption36Seat occupied recognition for US American marketA separate system was developed in order to meet the legal requirements in this country. The system is responsible for deactivating the passenger’s front airbag in certain circumstances. If the front passenger seat is unoccupied or if a child seat is detected, the front passenger airbag is switched off by the airbag control unit. A deactivated front passenger airbag is indicated by the PASSENGER AIRBAG OFF warning lamp and a corresponding message in the dash panel insert. This type of seat occupied recognition in the Audi A4 will now be used for the USA (new).The system comprises the following components: – Seat cushions – Mat for seat occupancy detection – Pressure sensor for seat occupied recognition G452 – Seat occupied recognition control unit J706 – Wearing belt recognition switch E25 – Seat belt force sensor for seat occupied recognition G453 – Warning lamp for airbag, front passenger side, off, K145 (PASSENGER AIRBAG OFF) – Airbag control unit J234Warning lamp for airbag, front passenger side, offSeat cushionsSwitch for wearing belt recognition Airbag control unitSeat belt force sensor for seat occupied Mat for seat occupied recognition Pressure sensor for seat occupied recognitionPlug-in connection under the seatIsolating point326_01937Passenger protectionPressure sensor for seat occupied recognition G452Pressure sensor for seat occupied recognition G452 is connected to the mat for seat occupied recognition by means of a hose. The mat, which is filled with a silicone-like gel is fitted below the seat cushion. If the front passenger seat is occupied, pressure is applied to this mat via the seat cushion. Pressure sensor for seat occupied recognition G452 generates an analogue voltage signal based on this pressure. The seat occupied recognition control unit supplies the pressure sensor with a voltage of 5 volts. The signal generated by the pressure sensor lies between approx. 0.2 and 4.3 volts, depending on the load on the seat. The higher the load, the lower the voltage.Pressure sensor for seat occupied recognitionProtective foilGel-filled mat for seat occupied recognition326_014Seat belt force sensor for seat occupied recognition G453The sensor element is located between the belt lock and the belt lock fastener, which is fixed to the seat frame. It consists of two movable parts. Both parts are held in their idle position by a defined spring. The seat belt force sensor operates by means of a hall sensor. On fitting the safety belt correctly, a tensile force is applied to the belt lock. The sensor measures the displacement distance of the parts to each other. The greater the tensile force, the greater the distance the parts are displaced. This changes the signal from the sensor. This information is evaluated by the seat occupied recognition control unit under the seat. A mechanical stop ensures that the sensor element is not torn apart in the event of a crash.Seat belt force sensor, unloaded326_052Seat belt force sensor, under load326_05138Wearing belt recognition switch E24 and E25The wearing belt recognition switch is fitted directly in the belt lock. Two resistors are integrated within the switch. The measurement is effected via one or both of the resistors, depending on the switch position. The airbag control unit recognizes that the safety belt has been put on by means of the measured resistance.R1R2326_020Switch for wearing belt recognition, belt not fastenedSwitch for wearing belt recognition, belt fastened326_053 326_05039Passenger protectionSeat occupied recognition control unit J706The control unit evaluates the signals coming from the pressure sensor and the belt force sensor. The seat occupied recognition control unit uses the information it receives from the seat belt force sensor to monitor the tensile force acting on the safety belt. The voltage signal from the pressure sensor can be used to specify the weight of the load on the front passenger seat. If the load is under approx. 20 kg, and a very small or no belt force is discernible, the control unit recognizes ”child seat” and informs the airbag control unit. The front passenger airbag is disabled. If the load on the seat is approx. 25 kg, for example, and the belt force exceeds a fixed value, the control unit recognizes that the safety belt is also pressing the child seat against the seat cushion. The control unit recognizes ”child seat” and the airbag control unit disables the front passenger airbag. From a load of approx. 25 kg and and a low belt force, the control unit assumes that the seat is occupied by an adult and the front passenger airbag remains active. The data from the sensors is continuously evaluated when the ignition is switched on. This ensures that the control unit recognizes any seat occupancy changes and reacts accordingly. When the vehicle is moving, the system no longer reacts spontaneously and only does so after a certain delay. This ensures that the front passenger airbag is not immediately deactivated when there is a load change on the seat whilst driving. The acceleration sensor in the control unit informs the electronics that the vehicle is moving.Seat load less than approx. 20 kg e. g. 25 kg greater than approx. 25 kgBelt force very small / none very high lowRecognition Child seat Child seat Adult40Data exchange between the seat occupied recognition control unit and other vehicle systems is effected via the airbag control unit (by means of the LIN bus). The airbag control unit is thus the master control unit and the seat occupied recognition control unit (J706) the slave. The Diagnosis function is effected via the airbag control unit.The positions of the installed components are fixed and must never be changed. This also applies to individual system components. The system, comprising control unit, pressure sensor, pressure mat and seat cushion, is calibrated individually for each seat during production. The connecting cable beween the control unit and pressure sensor is thus sealed at both ends in order to emphasize that they are not to be disconnected. Likewise, the pressure mat is connected to the foam by means of a clip, which cannot be removed without distroying it. All parts must be replaced together in the event of a defective component. Pre-calibrated Service kits are available for this. Components which are not installed correctly can cause malfunctions and the entire seat occupied recognition system can no longer operate reliably. Characteristic maps in the control unit electronics ensure that the ageing of individual components is taken into account.41DiagnosisDiagnosisAs in the case of the Audi A8´03 and Audi A3´04, communication in the Audi A6´05 between the VAS tester and the vehicle is effected via CAN-Bus, CAN-Diagnosis. The main Diagnosis modification is the Diagnosis tester online connection. An adaptation of components belonging to the immobilizer or interrogation of the radio code, is only possible when the tester is directly connected to the company's ”FAZIT” database. Secret numbers are thus no longer disclosed.294_001Reference For further information on the topic: VAS 5051 online connection; please refer to self-study programme 294.VAS 5053The VAS 5053 tester was developed for vehicle acceptance and service procedures and for smaller repairs. In addition to the ”Self-diagnosis” function, excerpts from the ELSA and the ”Guided functions” programme will be available on the tester. Due to its compactness, the VAS 5053 is suitable for portable use, e.g. test drives. The data gathered during a test drive can be stored in the tester until it is printed out. The connection between the vehicle and VAS 5053 tester is established by means of a cable. In addition, the tester can be connected to the vehicle via the separate VAS 5053/20 wireless interface.On-board vehicle diagnosis Read fault memory 2 fault detected 16519 P0135 Bank1-Probe1, heating circuit Electrical fault01 - Engine electronics 8D0907558F 1.8L R4/5V MOTR HS D02 Coding 4001 Workshop code 1948016518 P0134 Bank1-Probe1 No activitySprun gDruckenHilf eVAS5053326_03142VAS 5051The VAS 5051 A tester will be replaced by the VAS 5051 B in 2004. The hardware and design of the VAS 5051 have been revised and updated. The 15" screen is the most noticeable feature of the VAS 5051 B. The main objective of the revision was being able to use it on the existing instrument waggon and with the existing test cables.M esst echni k DSO0. 5V/O i v. =1m s/O i v. =N or m alBet r i ebTr i gger feh l t!St andbi l dKanalAKanalBTr i gger M ode0M ess M ode00. 5V/O i v. =0.0 0Pos itionDokum entM ess ung vore in gest ell tM ul ti m et erGeführ t e Fehl er suc heDr uck enHi l fe326_032Messtechnik DSO0.5V/Oiv.=1ms/Oiv.=Normal BetriebTrigger fehlt !StandbildKanal AKanal B 0Trigger-ModeMess-Mode00.5V/Oiv.=0.00PositionDokumentMessung voreingestelltMultimeterGeführte FehlersucheDruckenHilfe326_03343DiagnosisVAS 5053/20The VAS 5053/20 wireless Diagnosis interface permits wireless communication between the Diagnosis socket in the vehicle and the VAS 5051 B, VAS 5052 and VAS 5053 Diagnosis testers.VAS 50 52 / 20Messtechnik DSO0.5V/Oiv.=1ms/Oiv.=Normal BetriebTrigger fehlt !StandbildKanal AKanal B 0Trigger-ModeMess-Mode00.5V/Oiv.=0.00PositionDokumentMessung voreingestelltMultimeterDrucken HilfeGeführte FehlersucheDruckenHilfeSprungVAS 5053326_03444Recording the working time using the VAS 5051/5052From the basic CD 6.0 onwards, the actual working time in the ”Guided fault finding” and ”Guided functions” functions is logged by the tester and indicated in time units under ”Diagnosis time” in the Diagnosis log print-out. The time required to uncover or remove and install components in the scope of the guided fault finding process is not recorded by the tester.Workshop code: 02211 123 12312Version: Basic V06.02.00 19/06/2003 Audi V06.50.00 07/08/2003 Registration no.: AB-CD 1234Company code: VK-31Vehicle Ident. No.: WAUZZZ............. Vehicle: Make: Type: Model year: Variant: Engine identifier:Audi Audi A6 1998 2000 (Y) Allroad AKE 2.5l TDI / 132 kWDiagnosis time: Fault memory contents:36Motronic ME7 injection and ignition system 4Z7907401 2.5l/4VTEDC G200SG I02 Coding 1018 Company number 02325 1 fault detected 00575 008 Intake manifold pressure Control limit exceeded45Engine / GearboxOverview of available engine / gearbox combinationsV6 3.0l TDIV6 3.2l FSIV8 4.2l2.4l46Reference: For information on the engines and gearboxes, refer to SSP 3250A3/450Nm09L/to 450Nm01J/330Nm01X/02Xqu 330Nm09L/to 450Nm01J/330Nm01X/02Xqu 330Nm47ChassisOverviewThe basic version of the Audi A6´05 is equipped with a steel spring chassis. There are three different types of running gear: Normal chassis: Sports-style running gear: Designation 1BADesignation: 1BE, vehicle trim is positioned 20 mm lower than on the normal running gearBad road chassis: Designation 1BR, vehicle trim position raised by 13 mm compared to the normal chassisFront axleThe well-known four-link front axle also used in the new Audi A6‘05. Due to the geometric and kinematic modifications compared to the predecessor, all axle components, with the exception of the upper axle links and the wheel hubs (adopted from Audi A8), are new parts. In addition to improved spring and shock absorber settings, spring travel has been increased by 30 mm. This results in a significant improvement in driving comfort and driving stability. With regard to the passenger compartment, the axle was moved forward by 83 mm. This provides better axle load distribution and has advantages from the point of view of driving dynamics.Mounting blockSpring/shock absorber unit Guide arm Upper axle control armPivot bracketStabiliserSubframeSupporting armWheel bearing/ Wheel hub323_05048Rear axleThe rear axle represents a further development of the trapezoid link axle, with which you may be familiar from the A4’00. Because of the geometric and kinematic changes compared with the predecessor vehicle and the use of the trapezoid link axle, all axle components are new parts. The axle struts are now longer compared with the A4`00 in order to guarantee a larger toe width. For vehicles with the V8 TDI engine with quattro drive, the rear axle track width will be reduced in order to fit wider tires. This will be realised by using modified wheel hubs and a greater wheel offset.Wheel carrier SubframeTransverse control armShock absorberSpringTrapezoidal control armWheel bearing 323_05149ChassisWheel brakeFront-axle overviewEngine3.0 litre V6 TDI3.2 litre V6 FSI4.2 litre V8 MPIMinimum wheel size Brake type Number of pistons Piston diameter (mm) Brake disc diameter (mm) x thickness (mm)16” FNR-G 60 16” 2 60 321 x 30 Ventilated16” FNR-G 60 16” 2 60 321 x 30 Ventilated17” FNR-G 60 17” 2 60 347 x 30 VentilatedRear-axle overviewEngine3.0 litre V6 TDI3.2 litre V6 FSI4.2 litre V8 MPIMinimum wheel size Brake type Number of pistons Piston diameter (mm) Brake disc diameter (mm) x thickness (mm)16” Colette II C41 1 41 302 x 12 Not ventilated16” Colette II C41 1 41 302 x 12 Not ventilated17” Colette II C43 1 43 330 x 22 Not ventilated50ESPA new ESP generation from Bosch in the form of ESP 8.0 is used in the Audi A6'05. The familiar basic functions already available in the other Audi models have been adapted to the conditions in the A6´05. The basic functionalities of the subfunctions EBD, ABS, TCS, EDTC, EDL, ESP and ECD are the same as in the predecessor version 5.7. The control unit and hydraulic unit cannot be separated in Customer Service. There are two different parts for front-wheel-drive and quattro drive.Pump motorPilot valvesValve blockPressure sensorControl unit323_052Electromechanical parking brake – EPBFollowing its initial introduction in the Audi A8, the electromechanical parking brake EPB is now also used in the Audi A6´05. The basic mechanical design, the boost factor levels and the general functionality are still the same (see SSP 285). The innovations described in SSP 324 are due to its adaptation to the A6´05.323_05351ChassisSteering systemA conventional, hydraulic rack-and-pinion servo steering system is used. A high degree of sporty steering precision has been achieved through the consistent further development of the steering used in the predecessor model. The speed-dependent Servotronic servo-support is available as standard. Servotronic II, which was already used in the Audi A8, is used (set-up and mode of operation: see SSP 285). A mechanically adjustable steering column is used in the basic model. Electrical adjustment is optional. As in the case of the A8´03, the A6´05 also has an electrical steering lock. A newly developed three/four-spoke steering-wheel generation is used.Steering gearOil reservoirSuction hoseSteering pump Expansion hoseReturn hose Return lineServo oil cooler323_05452Wheels / tyresEngine 4 and 6-cylinderBasic wheels 7J x 16 ET 35 (1) Cast alum. wheel 205/60 R16 7.5J x 16 ET 45 (2) Forged alum. wheel 225/55 R16Winter wheels 7J x 16 ET 42 (4) Forged alum. wheel 205/60 R16 or 225/55 R16 225 x 460 ET 46 (5) Cast alum. wh. (PAX) 225/650 – 460Optional wheels 7.5J x 16 ET 45 (7) Cast alum. wheel 225/55 R16 7.5J x 17 ET 45 (8) Cast alum. wheel 225/50 R17 8J x 17 ET 48 (10) Cast alum. wheel 245/45 R17 8J x 18 ET 48 (11) Cast alum. wheel 245/40 R18Run flat system PAX 225 x 460 ET 46 (13) Cast alum. wh. (PAX) 235/660 – R4608-cylinder7.5J x 17 ET 45 (3) Cast alum. wheel 225/50 R177J x 17 ET 42 (6) Cast alum. wheel 225/50 R17 98 M+S7.5J x 17 ET 45 (9) Cast alum. wheel 225/50 R178J x 18 ET 48 (12) Forged alum. wheel 245/40 R18323_055Tyre pressure monitoring systemA new generation of the tyre pressure monitoring system is available for the Audi A6´05. It is modular in design and is significantly different from the systems used up to now at Audi from the point of view of functionality and design.53ElectricsBus topologyDistance control J428Control unit in dash panel insert J285Diagnosis interface for data bus J533 Data link connector T16NOX sensor J583Engine electronics 1 J623Door control unit, driver’s side J386Power management J644Rotation rate sensor G202ABS with EDL J104Door control unit, passenger’s side J387Auxiliary heating J364Seat occupied recognition J706Airbag J234Door control unit, rear left J388Parking aid J446Automatic transmission J217 Power module for left headlight J667 Headlight range control J431 Power module for right headlight J668 Electric parking / handbrake J540Door control unit, rear right J389On-board power supply 2 J520Seat adjustment with memory, steering column adjustment J136Access and start authorisation J518Seat adjustment with memory, pass. side J521On-board power supply J519Level control J197Trailer detection J345Central contr. unit for convenience system J393Sender for sensor G85Steering column electronics J527Climatronic J255Multi-function steering wheel J453Tyre pressure monitoring J50254Transmitter and transmitter and for telephone R36 Handset for telephone R37Display and operating unit for front information J523Telephone/telematics J526Navigation with CD drive J401CD changer R41TV tuner R78Digital sound package J525Radio module RVoice input J507MOST bus CAN Instrument clusterSwitch for access and start authorisation E415 Antenna read-in unit for keyless access authorisation J723CAN Diagnosis CAN Drive CAN Convenience CAN Distance control LIN busWiper motor J400Sensor for rain and light detection G397Passenger compartment monitoring G273Alarm horn H12Various sub-bus systems Wireless transmission - Bluetooth signalFresh air fan J126Refrigerant pressure and refrigerant temperature G395Transmitter, front left G431Transmitter, front right G432Transmitter, rear left G433Transmitter, rear right G434Antenna, rear R96 326_02755ElectricsIn/outputs on control units J393, J519 and J520This overview shows all load modules in the convenience system with their in/outputs. You thus have all 3 control units and their basic functions at a glance. For further details, please refer to the function plans in self-study programme 326 A6´05, Electrics. This overview only contains discretionary wired components. Components which communicate with the control units via various bus systems are shown in the vehicle topology.E1 Light switch E3 Hazard warning light switch F4 Switch for reversing lights F266 Contact switch for bonnet G357 Sender for vertical steering column adjustment G358 Sender for axial steering column adjustmentJ519 Onboard power supply control unit Master functions: – Exterior lights – Wiper and washerCAN Convenience Inputs (source) Outputs (receiver)J4 Relay for dual-pitch horn J39 Relay for headlight cleaning system K4 Indicator light for parking light K6 Indicator light for hazard warning lights E13 Indicator light for rear fog light E17 Indicator light for fog lights L13 Gas discharge light, left L14 Gas discharge light, right L22 Lamp for left fog light L23 Lamp for right fog light L174 Lamp for daytime driving light, left L175 Lamp for daytime driving light, right M1 Lamp for parking light, left M3 Lamp for parking light, right M5 Lamp for direction indicator light, front left M7 Lamp for direction indicator light, front right M18 Lamp for side direction indicator light, left M19 Lamp for side direction indicator light, right N395 Magnet for cover adjustment, left headlight N395 Magnet for cover adjustment, right headlight V5 Windscreen washer pump V123 Motor for vertical steering column adjustment V124 Motor for axial steering column adjustment W9 Footwell light, left W10 Footwell light, rightF218 Switch for tailgate central locking F248 Button for unlocking tailgate lock cylinder 530 Control unit for opening garage door (adaptation flashing) F124 Contact holder in lock cylinder for tailgate F334 Switch for tank cap detection (USA only) J234 Airbag (crash signal) Terminal 15 F Brake light switch J104 Control unit for ABS with EDL (ECD brake)56E316 Glove compartment buttonJ520 Control unit 2 for on-board power supplyN119 Solenoid valve for Servotronic V1 Motor for sliding roof: – Speed signal – Convenience opening – Convenience closing V327 Motor for glove compartment releaseJ393 Central control unit for convenience system Master functions: – Flashing – Central locking – Interior light – Anti-theft warning systemJ9 Relay for rear window heater L106 Lighting for footwell, rear left L107 Lighting for footwell, rear right M2 Lamp for tail light, right M4 Lamp for tail light, left M6 Lamp for direction indicator light, rear left M8 Lamp for direction indicator light, rear right M9 Lamp for left brake light M10 Lamp for right brake light M16 Lamp for reversing light, left M17 Lamp for reversing light, right M25 Lamp for high-level brake light M49 Lamp for tail light 2, left M50 Lamp for tail light 2, right M54 Lamp for tail light 3, right M55 Lamp for tail light 3, left V1 Motor for sliding roof (release) V53 Motor for tailgate central locking V91 Motor for rear sun blind V155 Motor for tank cap locking W3 Boot light W35 Boot light, right X Number plate lights Terminal 30 for interior light (switched) Door contact signal, interior light (dimming ground-controlled) Door contact signal for engine control unit (FSI only) Door contact signal for air suspension323_01857Air conditioningOverviewThe new Audi A6´05 is equipped with an air conditioning system as standard. A differentiation is made between automatic air conditioning and convenience automatic air conditioning plus. The main characteristics of the air conditioning system in the new A6´05 are the low interior noise level, no-draught ventilation and even temperature distribution. During the development process, particular attention was paid to weight and space-saving but output-optimized) components.323_012Air conditioning unit for Audi A6´98 The familiar air conditioning concept used in the AUDI A6 predecessor has been replaced by a symmetric concept, in which the fresh air blower is located outside the passenger compartment. The previous air-based air conditioning control system has been converted to a water-based control system with valves for heating control left and right (N175/ 176 ) and a pump for coolant circulation (V50) like in the current Audi A8. The new concept is more or less the same for both the left-hand and right-hand drive variants. This reduces the number of variants.Reference For information on the 6-piston swash-plate compressor, please refer to SSP 240, Audi A2 – Technology.58Audi A6´05 air conditioning unit The new Audi A6´05 – like the Audi A2 and Audi A3´04 – will be equipped with the familiar 6-piston swash-plate compressor with control valve N280 and out-flow temperature sender for evaporator G263. The compressor has the same working volume of 140 cm3 for all country variants. In the case of the 4 and 6-cylinder engines, it is driven via a plastic belt pulley and in the case of the 8-cylinder engine, via a shaft.323_011323_01359Air conditioningConvenience automatic air conditioning and convenience automatic air conditioning plusThe new Audi A6´05 will still use an automatic air conditioning system with two-zone temperature control as standard equipment. Both the basic and convenience versions now have a circulating air filtering system (extended function) in which the filter element has been integrated within the distributor housing. Both versions have a central nozzle with adjustable temperature in the dash panel insert. The control for the optional seat heating and ventilation is integrated within both variants of Climatronic control unit J255. Both versions of the automatic air conditioning system use the respective display on the multimedia interface as the display unit. They are still operated at the separate Climatronic control unit J255).323_014The automatic air conditioning plus system also has two additional displays in Climatronic control unit J255. Furthermore, it also has an indirect ventilation in the dashboard.In addition, an air quality sensor for automatic fresh air / circulating air changeover is installed. The residual heat function makes it possible to use the engine heat when the vehicle is stationary.323_01560Convenience automatic air conditioningConvenience automatic air conditioning PlusA6 PredecessorSeparate temperature distibution Sun position sensor Air quality sensor Residual heat Pollen filter / combination filter Circulating air filter Indirect ventilation Rear compart. ventilation (middle) Rear compartment ventilation (B-pillar) Central air vent with adjustable temperature Control conceptX X X/X X water-basedX X X X -/X X X X X X water-basedX X X -/X X air-basedCAN networkingThe air conditioning system in the new Audi A6´05 is integrated within the convenience CAN (see table). In addition to the air conditioning master control, Climatronic control unit J255 is the master control unit for the distributed functions rear window heating, the