TECHNICAL DOCUMENTATION
SSP 048 Škoda Superb V6 Internal Combustion Engine 2.8 litre

This PDF is currently unavailable.
Read document text
Service ŠkodaSuperb48V6 Internal Combustion Engine 2.8 litre/142 kWSelf-Study ProgrammeThe new ŠkodaSuperb ......... with a V6 engineSP48_62Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�This is the first time that Škoda has used a V6 engine, in the new ŠkodaSuperb, the first vehicle from Škoda in the upper middle class. The longitudinally mounted 2.8 litre/142 kW engine using five valve technology originates from the VW/Audi range of engines and • has a high performance and a high torque with a correspondingly low fuel consumption, • is fitted out with a modern engine management system. The engine is built into vehicles with either a 5-speed manual gearbox or an automatic gearbox with five driving positions.2GBContentsIntroduction Technical overview Engine management Motronic ME7.1 A system overview for the Motronic ME7.1 Positions of the various components A function plan Engine mechanics The crankcase and crankshaft drive The cylinder head and valve gear The camshaft adjuster The timing belt drive Drive for the ancillary units The visco fan coupling The switching intake manifold Engine lubrication The oil circulation system Components of the oil circulation system Cooling Ventilation of the crankcase The vacuum system Supply the engine with fuel The exhaust system The secondary air system Self-diagnosisProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�4 5 5 6 8 10 13 13 16 17 19 21 22 25 26 26 27 29 31 32 34 35 36 38 39NotesServicexxxxxxxxxxxxxxxx SUPERBServicexxxxxxxxxxxxxxxx SUPERBServicexxxxxxxxxxxxxxxx SUPERBService Servicexxxxxxxxxxxxxxxx SUPERB xxxxxxxxxxxxxxxx SUPERBService Servicexxxxxxxxxxxxxxxx SUPERB xxxxxxxxxxxxxxxx SUPERBS e r v i c eXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXYou can find information regarding inspection and maintenance, setting and repair instructions in the Workshop Manuals.GB3IntroductionTechnical overviewTechnical features – – – – – – – – – – V6 engine with 5-valve technology 2 overhead camshafts (DOHC), inlet camshaft with hydraulic adjustment an electronic fuel injection system with integrated performance map ignition cylinder-selective knocking regulation a maintenance-free ignition system with dormant high voltage ignition distribution a switching intake manifold 2 pre-catalytic converter lambda probes 2 post-catalytic converter lambda probes a secondary air system fulfilment of all EU4 standardsSP48_01Technical dataEngine code Type Number of cylinders Valves per cylinder Compression ratio Displacement Bore diameter Stroke Max. power output Max. torque Engine management AMX V-engine 6 5120 400 150 50013545010.6 : 1105 3502771 cm390 30082.5 mm 86.4 mmP (kW)75250142 kW at 6000 rpm 280 Nm at 3200 rpm Bosch Motronic ME7.16020045150Fuel /air mixture Electronic fuel injection 30 preparation plant (MPI) Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� 1510050FuelPetrol, lead-free RON 98 (RON 95 is possible with some reduction in performance)01000200030004000500060007000n (min –1 )SP48_024GBM (Nm)Engine ManagementMotronic ME 7.1The engine control ME 7.1 operates through orientation on the torque. This allows the Electronic Throttle System Function to operate. External and internal demands for torque are co-ordinated by the engine control unit while taking due consideration of the operating efficiency and the exhaust gas standard (EU4) and are translated into action over the available actuators. The engine management system is fitted with a rapid start function. Two camshaft position sensors and an engine run-out recognition system (position of the next cylinder in line at the ignition top dead centre) create the conditions whereby one can immediately begin to spray in fuel. This has a positive effect on the starting behaviour.Note: There are also functions for the 3rd generation of vehicle immobilisers integrated in the ME 7.1 (see SSP 46).PartFunctionPartFunctionSequential fuel injection (see SSP 19)SP48_04_1Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�AKF systemSP48_04_6λSP48_04_2Lambda regulation of the two cylinder banksSP48_04_7Torque-oriented engine managementPerformance map ignitionSP48_04_3SP48_04_8Electrically operated throttle valve (Electronic Throttle System Function) (see SSP 27)Knocking regulation of the two cylinder banksSP48_04_4 SP48_04_9Performance map inlet camshaft adjustment (see page 18)Dormant high voltage ignition distribution over an ignition transformerSP48_04_5 SP48_04_10Secondary air system (see page 36)GB5Engine ManagementA system overview for the Motronic ME7.1SensorsAir mass flow meter G70Sender for the engine speed G28Hall sender (Bank 1) G40 and (Bank 2) G163 (camshaft position sensor)Lambda probe (Bank 1) G39 and G130 Lambda probe (Bank 2) G108 and G131Throttle valve control unit J338 with angle sender (1) G187 and (2) G188Sender for the inlet air temperature G42Sender for the coolant temperature G62Knocking sensor (Bank 1) G61 and (Bank 2) G66Accelerator pedal module with sender for the accelerator pedal position G79 and G185Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Brake light switch F and brake pedal switch F47Clutch pedal switch F36 Additional signals: - air-conditioning compressor - On - driving speed - switch for the speed control equipment6GBActuatorsFuel pump relay J17 and fuel pump G6Injection valve (Bank 1) N30, N31, N32Injection valve (Bank 2) N33, N83, N84Ignition transformer N152Magnetic valve for the active charcoal filter system N80 W-line Valve for variable intake manifold changeover N156Protected by copyright. Copying for private or commercial purposes, in valve part or in control whole, is not permitted Throttle unit J338 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by Š KODA AUTO A. S. � valve drive G186with a throttleGatewayValve for camshaft adjustment (Bank 1) N205 and (Bank 2) N208CAN driveK-lineHeating for the lambda probes (Bank 1 und 2)Secondary air inlet fan valve N112Relay for the secondary air pump J229 and motor for the secondary air pump V101 Additional signal: - air-conditioning compressor - Off 7SP48_05GBEngine ManagementPositions of the partsSecondary air fan valve N112 Sender for the coolant temperature G62Valve - 1 - for camshaft adjustment N205Solenoid valve 1 for the active charcoal filter system N80Air mass meter G70Knocking sensor I G61Motor for the secondary air pump V101Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Hall sender G40 (camshaft position sensor)Ignition transformer N1528GBSender for the inlet air temperature G42Valve for variable intake manifold changeover N156Throttle valve control unit J338Control unit for Motronic J220Fuel pressure regulatorHall sender 2 G163 (camshaft position sensor)SP48_03Sender for engine speed G28Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTOValve A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability 2 for camshaft adjustment with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Knocking sensor II G66N208GB9Function planJ1730 15SB28 20ASB32 20ASB34 15AN30N31N32N33N83N84G39G130G108G131λλλλProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�65 3 9611288971138932 5 51 7063 68 694 12 136 10 11117 118 928384 91 33 72 34 36 35 73 1088290879886+MJ338o++ -oG6MG186G187G188G185G79G28 G40G16331Legends to the function plan See page 12. 10GB30 15SB130 40ASB13 10ASB7 10ASB31 15ASB29 20A31 N80 G70 N156 N205 N208 N112 J299MV101FF47F361234564 J220 99 10753 27 29 10411544 4658605443415655396240106938557 75 1576 381 294103102G66G61G62G42E227E45III V II IV IN152VIinoutP Q31Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability SP48_48 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB11Function planLegends to the function plan ComponentsE45 E227 F F36 F47 G6 G28 G39 G40 G42 G61 G62 G66 G70 G79 G108 G130 G131 G163 G185 G186 G187 G188 J17 J220 J299 J338 N30 N31 N32 N33 N80 N83 N84 N112 N152 N156 N205 N208 P Q SB V101 12Additional signalsSwitch for the speed control equipment 1 CAN drive (Low) Key for the speed control equipment 2 CAN drive (High) (set) 3 Driving speed signal Brake light switch 4 W-line Clutch pedal switch 5 Air-conditioning compressor - Off/On Brake pedal switch Fuel pump Sender for the engine speed Lambda probe before the catalytic converter Hall sender Sender for the inlet air temperature Knocking sensor I Sender for the coolant temperature Knocking sensor II Air mass meter Sender for the accelerator pedal position Colour coding/legends Lambda probe II before the catalytic converter Lambda probe after the catalytic = input signal converter Lambda probe II after the catalytic = output signal converter Hall sender 2 = battery positive Sender 2 for the accelerator pedal position = earth Throttle valve drive = CAN bus Angle sender 1 for the throttle valve drive = bi-directional Angle sender 2 for the throttle valve drive Fuel pump relay Control unit for the Motronic Relay for the secondary air pump Throttle valve control unit Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Injector for cylinder 1 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Injector for cylinder 2 Injector for cylinder 3 Injector for cylinder 4 Solenoid valve 1 for the active charcoal filter system Injector for cylinder 5 Injector for cylinder 6 Secondary air fan valve Ignition transformer Valve for variable intake manifold Note: changeover The function plan shows a Valve 1 for camshaft adjustment simplified electrical circuit Valve 2 for camshaft adjustment diagram. Spark plug terminal Spark plug Fuse Motor for the secondary air pumpsGBEngine MechanicsThe crankshaft and crank driveThe 90o V construction allows one to build an engine with a lower constructional height which also, at the same time, offers much space between the cylinder banks for mounting the compact inlet manifold. There is a settling chamber located under the inlet manifold for crankcase ventilation which is closed off with an aluminium cover. The thermostat and coolant pump housings are integrated into the rear side of the crankcase. This coupled with the lower displacement of the row of cylinders by 18.5 mm means that a shorter constructional length is achieved. The crankcase is made out of cast iron.Settling chamber for crankcase ventilationThermostat housingProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Coolant pump housingSP48_07Cross-screw connectionThe crankshaft The crankshaft sits on four bearings and the middle bearing caps are screwed to the crankcase crosswise on both sides to obtain a stiffening effect. Advantage: Improved engine acoustics. Large counterweights on the crank arms serve to achieve optimum mass balancing.SP48_30CrankshaftSP48_08GB13Engine MechanicsThe crank pin throw A V6 engine has an equal ignition spacing between the cylinders of 120 o. This means that there should be a 30o throw of the three crankshaft pins because of the V-angle of 90 o between the two cylinder banks. The effect of the crank pin throw The piston rod for Cylinder 1 and 4 Cylinder 2 and 5 Cylinder 3 and 6 is located on each of the cranked (split) crankshaft pins.Ignition sequence: 1 - 4 - 3 - 6 -2 -53 2 1V6 V6 30V 30V6 5 4SP48_09 Position of the crank pin of cylinder 4 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability for cylinder 1 at TDCwith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�90°Cylinder 1Cylinder 4The crank pin of cylinder 4 is running at 30o after the crank pin of cylinder 1SP48_10... after a 120o turn of the crankshaftCylinder 1 Cylinder 430°Position of the crank pin of cylinder 4 for cylinder 4 at TDC120°SP48_11Position of the crank pin of cylinder 4 for cylinder 1 at TDCA 120o turn of the crankshaft = the ignition interval 14GBPistons The engine is fitted with pistons which have piston bolt eyes located close together. The piston bolts which are somewhat smaller in length and diameter allow reduction of the masses which are moving back and forth (oscillating). The piston cooling is achieved through using piston spray jets in the crankcase. The piston shaft is fitted with a wear-resistant, graphite-containing gliding layer which is applied by a screen printing process.Graphite-containing gliding layerSP48_12Con-rods The V-6 2.8 litre/142 kW engine is fitted with lightweight cracked steel con-rods. The con-rods on this engine perform an eccentric crank movement reciprocally on the cranked crankshaft pins. Wear is avoided due to the convex shaping of the side surfaces.Bearing shellsConvex shapingThe upper and lower bearing shells are made Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability out of three unless materials (composite material): with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� – – – steel lead bronze a galvanised layer (lead, tin, copper)The advantage: Small pieces of dirt from the engine oil can get embedded in the lead bronze layer which can then no longer damage the bearing like an abrasive. This means that one can achieve a much higher working life for the bearing.SP48_13TipNote: The convex shapings (peak of the conrod bearing cover) of the con-rod must stand opposite each other.GB15Engine MechanicsThe cylinder head and valve gearThe cylinder heads are designed as cross-flow heads due to the central intake manifold. This allows advantageous configuration of the inlet channels and thus good filling of the cylinder. The drive of the two camshafts takes place from the rear over a timing belt (see page 19). The five valve technology is the same as that used on the 1.8 litre engine on the ŠkodaOctavia (see SSP 23). The camshaft adjustment system only adjusts the inlet camshaft.Valve 1 - for camshaft adjustment N205Hall sender 2 G163 (camshaft position sensor)Hall sender G40 (camshaft position sensor)Valve - 2 - for camshaft adjustment N208Camshaft wheelSP48_14Camshaft wheelInletunless camshaft authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedThe construction of the V6 engine places particular demands on the camshaft adjustment. Viewed from above the outlet camshafts are on the outside while the inlet camshafts are in the inside. This means that the camshaft adjustment system on the left and right cylinder bank must work in opposition to each other.SP48_15Outlet camshaft 16GBCamshaft adjustment system(Cylinder bank 1)Clamping piston Chain tensioner sliding block Hydraulic cylinder with switching pistonsOil reserve chamberValve for the camshaft adjustmentSP48_43Locking pin for the start phaseAdjusting pistons Sliding blockThe system used for adjusting the camshafts in the 1.8 engine is also used in the V6 5-valve generation of engines. There is no oil pressure being applied to the chain tensioner and the camshaft adjustment mechanism when the engine is not running.The V6 5-valve engine was subjected to further development and the tried and tested system received a locking function and an oil reserve chamber.These new developments prevent vibrations arising in the chain drive which thus have a positive effect on the noise generated when Protected by copyright. Copying for private or commercial purposes, in part or in up whole, is notengine. permitted starting the On the starting the 1.8 litre engine, and until unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect tohas the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� sufficient oil pressure built up, the chain The position of the locking pin is different for drive vibrates due to a reversal of stress the camshaft adjusters on cylinder banks 1 reaction, which produces noise. and 2.Note: You can inform yourself extensively about the principle of the camshaft adjustment mechanism in the Self-Study Program No. 19.GB17Engine MechanicsCamshaft adjustment system(Cylinder bank 2)Oil supply point Lubrication and Air ventilation holeWith the engine off: A spring-loaded locking pin is pressed into the resting groove of the adjusting when there is no oil pressure.Locking pinOil returnAOil reserve chamberBAdjusting pistonSP48_44BAWhen the engine is started: The adjusting piston is locked until sufficient oil pressure has built up and prevents vibrations occurring in the chain drive and therefore the generation of noise. The camshaft adjuster is blocked in the direction "late position".Control channelsLate position (basic or power position)ABThe engine is running: Once a pre-determined oil pressure is reached this acts upon the surface of the locking pin and thus against the force of the spring. The locking pin frees the adjusting piston so that it can be moved in the direction of "early position" in according to activation from the engine control unit.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�BASP48_45Early position (torque position)The oil reserve chamber Ensures that the clamping piston pressure chamber is filled up without being under pressure in the start phase. This also has a positive effect on the generation of noise while the engine is being started. A bore hole on the upper end of the oil reserve chamber allows air to be ventilated from this part and delivers oil to the chain.ABBASP48_4618GBThe timing belt driveThe timing belt sprocket - crankshaft drive: – – both camshafts on cylinder banks 1 and 2 the coolant pump The timing belt tension is set hydraulically from a tensioning element over the cocking lever and the tensioning roller. The deflection roller, tensioning roller, hydraulic tensioning element and cocking lever are fixed onto the sealing flange at the front.The tensioning roller and the deflection roller in the timing belt drive are arranged in such a way that an angle of wrap of 210o is obtained on the timing belt sprocket - crankshaft.Camshaft sprocket Cylinder bank 1Coolant pumpCamshaft sprocket Cylinder bank 2Tensioning rollerCocking leverDeflection rollerSP48_16Hydraulic element Tensioning elementProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Timing belt sprocket CrankshaftGB19Engine MechanicsAdjustment of the timing belt The piston of the third cylinder must be at TDC in order to adjust the valve timing of the valve drive. This position is determined by a mark on the timing belt sprocket - crankshaft and the timing belt cover. The crankshaft is securely interlocked into this position using a stop screw.Stop screwSP48_18Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Camshaft with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The camshafts on cylinder banks 1 and 2 must stand in a particular position relative to each other. The camshaft sprockets should be adjustable on the camshaft as for a diesel engine in order to balance out tolerances.Fixing plateSetting takes place using a camshaft fixing device. The camshaft and fixing plate are bound snugly together. The camshaft sprocket can be turned at the cone of the camshaft. The camshaft sprocket is then firmly screwed to the camshaft when the camshaft fixing device is mounted.SP48_17Camshaft fixing deviceNote: You can inform yourself extensively about setting up a timing belt in the Service Manual.20GBDrive for the ancillary unitsThe drive for the ancillary units takes place over a V-ribbed belt. This drives: – – – – the AC generator the air-conditioning compressor the vane pump for the power-assisted steering the visco fan couplingVane pump for the powerassisted steeringBelt pulley for the visco fan coupling Tensioning rollerProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP48_19GeneratorVisco fan coupling with fan wheelTiming belt sprocket crankshaftAir-conditioning compressorGB21Engine MechanicsThe visco fan couplingThe fan for the engine cooling is regulated over a visco fan coupling depending on the temperature. This means that it only operates when additional engine cooling is required. The visco fan coupling runs maintenance-free. The adjusting screw must not be turned. Advantages: – more power output from the motor – less fuel consumption – less noiseCoverBase bodyInstallation and function The visco coupling consists essentially of two chambers: – the work chamber with the drive disc which fits snugly together with the flange shaft and – the storage chamber with an intermediate disc which is bound friction-locked with the base body of the coupling.External bi-metallic strip Internal bi-metallic strip Valve rockerValve openingDrive disc Flanged shaftThe intermediate disc has a valve opening and Adjusting the pump body (angular nose). The valve screw rocker is fixed to this which opens the trip dog of the valve over the external bi-metallic strip Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Trip dog depending on the temperature. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The viscous oil circulates around the body of the pump and the valve opening between the operating chamber and the oil reserve chamber. The more viscous oil there is in the operating chamber the greater the frictional bond between the drive disc and the base body of the coupling and therefore the higher the rotational speed of the fan.SealWork chamber Intermediate discReserve chamber with viscous oilPump bodySP48_56Cover with trip dog and seal External bi-metallic strip with adjusting screwPump body Intermediate disc with valve rocker Drive disc Base body flange shaft22SP48_52GBThe diagrams for the rotational speed of the fan and the power output of the drive generally apply for all operating conditions of the engine - cold/warm/hot.22502,25Rotational speed of the fan (rpm)A2000 2,00Power output of the drive (kW)1750 1500 1250 1000 7501,75 1,50 1,25 1,00 0,75 0,50 0,25AB500 250 0B0 0 1000 3000 5000 7000 9000010003000500070009000Rotational speed of the drive (rpm)SP48_57Rotational speed of the drive (rpm)SP48_58The rotational speed of the fan will fall off at higher temperatures at the external bi-metallic strip and a rotational speed of the drive in excess of 4000 rpm because of the lower viscosity of the viscous oil (internal friction).A - coupling fully connected in for a temperature on the external bi-metallic strip of ≥ 85 oC B - coupling fully disconnected for a temperature on the external bi-metallic strip of ≤ 40 oCEngine cold The rotation of the drive disc causes the viscous oil to be pumped out of the operating chamber over the pump body into the reserve chamber. The valve rocker which is actuated over the external bi-metallic strip/trip dog closes the valve opening so that no viscous oil can flow back into the operating chamber. There is no frictional bond between the drive disc and the base body of the unit when the operating chamber does not contain any oil which means that the fan only turns at a low slave rotational speed (internal friction).Drive - motor Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Drive - fan in this document. Copyright by ŠKODA AUTO A. S.� with respect to the correctness of information Viscous oilSP48_53GB23Engine MechanicsInternal bi-metallic stripExternal bi-metallic stripProtected byDrive copyright. for private or commercial purposes, in part or in whole, is not permitted - Copying motor unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness Drive - fan of information in this document. Copyright by ŠKODA AUTO A. S.�Viscous oilSP48_54SP48_55Engine warm The valve rocker which is actuated over the external bi-metallic strip/trip dog opens the valve opening so that viscous oil can flow into the operating chamber. This creates a connection between the drive disc and the intermediate disc/base body of the unit. The rotational speed of the fan increases. The viscous oil is then pumped between the operating chamber and the reserve chamber where the amount of oil pumped depends upon the difference in rotational speed between the drive disc and the intermediate disc/base body of the unit.Engine hot The higher the ambient temperature at the external bi-metallic strip becomes, the greater the upward thrust of the valve rocker. This causes more viscous oil to flow into the operating chamber and the maximum rotational speed of the fan is then achieved. The difference in rotational speed between the drive disc and the intermediate disc/base body of the unit in this operating condition is at its lowest. This also means that only a small amount of viscous oil is pumped from the operating chamber into the reserve chamber. An internal bi-metallic strip protects the visco fan coupling from thermal overload. It supports itself on the cover at certain temperatures and therefore works against the upward thrust of the valve rocker.24GBThe intake manifoldA switch-over roller is installed which allows the length of the intake manifold to be set to two different values in order to optimise the available torque and power output achievable. One torque and power channel is created per cylinder from a common collective volume. They are brought together again before the injector. The switch-over roller arranged in the power channel opens the shorter power channel through a 90o turn at 4360 rpm which means that less air now flows through the torque channel. The power channel is closed again at 4280 rpm. Actuation of the switching roller is undertaken over a vacuum setting element. The control is undertaken by the engine control unit for the variable intake manifold changeover.Intake manifoldVacuum setting elementInlet manifoldSwitch-over rollerThe seal between the individual channels is achieved using separate sealing rings. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP48_26Torque positionPower positionChannel length: 575 mmSP48_27Channel length: 310 mmSP48_28GB25Engine lubricationThe oil circulation systemA duo-centric oil pump sucks up the oil over a large mesh filter. There is an oil pressure limiting valve located in the pressure chamber of the pump to protect downstream components from pressure peaks arising when starting from cold. The oil is led over the oil cooler to the oil filter. The oil then flows into the main channel and a branch line leads to the oil pressure regulating valve (on the clean oil side). The main channel feeds: – the four crankshaft bearings – the three piston spray jet pairs above the spray jet valve – the cylinder heads above one oil nonreturn valve respectively The camshaft adjusters are subjected to the full oil pressure. The oil pressure to the lubrication system for the camshafts and hydraulic driver rod is reduced over a throttling point.Cylinder bank 1 on the rightThrottling pointACylinder bank 2 on the leftBAPA BOil nonreturn valveB ASpray jet valve CamshaftsHydraulic driver rod Main channel Oil pressure regulating valve Oil pump Suction filter (large mesh filter) Oil flow under pressure 26 Oil flow under reduced pressure Oil pressure limiting valve (overpressure valve)SP48_29Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�from oil cooler/oil filter to oil cooler/oil filterOil flow without pressureGBThe components in the oil circulation systemThe oil pump is an inner gear pump. This is attached as a separate component to the crankcase. This type of construction allows the oil pump to reach deeply into the oil pan. It plunges completely into the engine oil when the oil level is correct which avoids the pump from running dry. This, in connection with a very short suction length, allows rapid and secure build-up of the oil pressure, particularly from a cold-start. The drive on the oil pump is achieved from the crankshaft over a simple chain. A springloaded sliding block (chain tensioner) ensures that the chain is the under the correct tension. One uses a chain shield made out of steel metal plate which encapsulates the chain wheel and chain within a generous volume. This is a reliable antidote for foaming of the oil and all that that entails.Oil pressure limiting valve Oil pressure regulating valveChain coverSP48_31The oil filter contains a filter element and the filter bypass valve. The latter has the purpose to maintain engine lubrication over the filter bypass valve even when the filter element is blocked up or the oil viscosity is high.The oil coolerFilter elementFilter bypass valveis integrated into the main stream of flowing Protected by stream copyright. Copying for private or commercial oil. Theunless whole is fed over the oil purposes, in part or in whole, is not permitted authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability cooler. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� The spray nozzle valve frees up the oil stream to flow to the piston spray nozzles once an oil pressure of greater than 0.18 Mpa (1.8 bars) has been reached. The reason: The oil pressure would drop below the admissible minimum value at low viscosity and lower rotational speeds. It is also not necessary to use piston cooling at lower rotational speeds.Oil filterOil coolerUpper part of the oil panSP48_65from the oil pumpto the main oil channelGB27Engine lubricationOil pressure regulating valve regulates the oil pressure in the engine. It is situated in the housing of the oil pump. The "diverted" oil is led to the suction side which contributes to optimisation of the efficiency. The oil non-return valve prevents the situation arising where the oil runs back from the cylinder heads to the oil sump when the engine is not running.Oil pressure limiting valve is a safety valve. It is installed in the oil pump housing and opens when the oil pressure is too high (during a cold start). Components in the oil circulation system can be damaged if the oil pressure is too high (e.g. the oil filter, oil cooler) and it is also possible through "pumping up" of the hydraulic driver rod that the inlet and outlet valves no longer close. This would mean that the engine would not start-up.The throttling points prevent "over-flowing" of the cylinder heads. A lot of oil finds its way into the cylinder heads at high engine speeds which has to be transported away over the oil return bore holes. The throttling points reduce the oil flow and thus secure the return flow.Cross holeThe "integrated oil supply system" Each camshaft bearing is supplied with oil from a bore hole which comes from the main channel of the cylinder head. The oil is led along in the bearing cover on the screw shaft to a transverse bore hole. A lubrication groove distributes the oil in the camshaft bearing so a separate pipeline to the individual bearing covers is not needed. Advantages: – – – less components more rapid and even oil supply lower costsProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Main channel of the cylinder headSP48_3228GBCoolingThe coolant circuitThe engine has a conventional longitudinal stream cooling system. – – inlet on the cylinder block at the front outlet on the cylinder block at the rear The coolant is then led from the gathering chamber in the cylinder head to the rear in the connecting pipe. The thermostat opens the large coolant circuit and also closes the connection from the thermostat housing to the connecting pipe at the same time.Both cylinder banks are supplied with coolant from the coolant pump chamber. The coolant flows from the cylinder block vertically into the cylinder head whereby the exhaust gas sides are more intensively fed with coolant than the other sides (larger cross-sections).Smaller coolant circuitNote: Please observe the instructions given in the Service Manual for filling and the coolant Protected by copyright. Copying for private or commercial purposes, in part or inventilating whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability circuit. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Pump for the coolant return flow Thermostat Coolant pumpThrottle valve control unit ATF cooler (integrated into the radiator)Engine oil coolerHeat exchangerRadiatorSP48_33Flowing coolant Stationary coolantCompensation bottleGB29CoolingLarger coolant circuitPump for the coolant return flow ThermostatCoolant pump Throttle valve control unitATF cooler (integrated into the radiator)Heat exchanger Engine oil coolerSP48_34Radiator Flowing coolant Coolant which is not moving Compensation bottlePump for the coolant return flow The pump for the coolant return flow V51 is additionally built onto vehicles in countries which have a high ambient temperature. Function:Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted The pump for the coolant return flow is unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� generally actuated for 10 - 12 seconds some 15 seconds after switching off the ignition. The fan for the coolant V7 is also switched on if the coolant temperature is greater than 92 oC.SP48_39Pump for the coolant return flow V5130GBVentilation of the crankcaseThe ventilation system for the crankcaseconsists of a distribution piece, a ventilation valve and the associated hosing. The oil which also comes out of the crankcase and the two cylinder heads is led back to the oil circuit. In This is achieved by installing an oil separation plate in both cylinder head covers. The rest of the oil mist and the blow-by-gases are then led together in the distribution piece out of the cylinder heads and the crankcase. The ventilation valve (a differential pressure controlled membrane valve) controls the return flow of the gases for burning depending on the inlet manifold pressure.to the inlet manifoldSP48_35Cylinder head cover on the left Inlet manifold Cylinder head cover on the rightfrom distributorVentilation valveSP48_36Distributor piece Cover of the calming chamber for crankcase ventilationProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Oil separatorNote: The blow-by-gases are those gases which leak by the piston rings in the crankcase.SP48_51GB31The vacuum systemAn overview of the vacuum systemVehicles with a manual gearboxValve for the variable intake manifold changeover N156 Vacuum vessel Fuel pressure regulating valve Throttling flap Inlet air hood Secondary air inlet valve Non-return valve Combination valve for secondary airSP48_37Vacuum box for the variable intake manifold changeoverSuction pipe Solenoid valve for the active charcoal container N80Active charcoal containerSuction jet pumpBrake boosterFunction of the suction jet pumpProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Connection for with respect tothe the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� brake boosterConnection for the suction pipeABConnection for the inlet air hoodABSP48_59SP48_61Throttling flap closed or slightly opened (idling/thrust/low loading) – a large pressure differential before/behind the throttle valve, air suction from the inlet air hood high vacuum in Chamber B due to the high throughflow speed in the narrowed crosssection (Venturi nozzle) non-return valve in Chamber B openStart phase (no vacuum or very little in the brake booster) – – – – a large pressure differential between the brake booster and the suction pipe a vacuum in Chamber A a low level of vacuum in Chamber A non-return valve in Chamber A open––32GBVehicles with an automatic gearbox The supply of vacuum to the brake booster on vehicles fitted with an automatic gearbox is different to that shown on page 32 for vehicles fitted with a manual gearbox.Control unit for the Motronic J220Pressure sensor for the brake booster G294RelayVacuum pump runningVacuum pump for brake V192Brake boosterProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Non-return valveVacuum pump not runningSP48_60The electrical circuit The steadily increasing loading requirement (further opening of the throttling flap) for some operating conditions, e.g. the catalytic converter heating phase when idling after starting up the engine, leads to reduction of the ability of the engine to provide a vacuum. An electric vacuum pump is installed to ensure that the brake booster has an adequate supply of vacuum for every engine operating condition. The vacuum pump switches on when the vacuum in the brake booster falls below a certain level and continues to run until an adequate supply of vacuum has been built up.31SP48_49+15J22045 18 98J569+30MV192G294GB33Supply the engine with fuelThe fuel systemis constructed analogue to that for the previous 4-cylinder engines.Fuel distributorPressure regulatorProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�InjectorSP48_38The fuel pump in the fuel tank pumps the fuel at a pressure of at least 0.4 Mpa (4 bars). The fuel passes over the fuel filter into the fuel distributor where it is evenly fed on to the six injectors. The injection system pressure is 0.4 Mpa (4 bars) minus the pressure in the vacuum pipe. The pressure regulator is located in the return flow of the distributor and regulates this pressure. A direct hose connection from the pressure regulator to the suction pipe ensures that the pressure differential between the suction pipe and the pressure of the fuel in the distributor remains constant.The volume of injected fuel is therefore independent of the suction pipe pressure and only depends upon the period of duration of injection. Fuel which is not needed flows back through the pressure regulator over the fuel return line to the fuel tank. The injectors have a two-hole nozzle which provides an homogenous fuel-air mixture and therefore achieves optimum combustion.34GBThe exhaust gas systemStructureThe exhaust gas system essentially consists of: – two pre- and main catalytic converters each with a heatable two-point lambda probe (Bosch LSF 4.7) – A front, middle and rear silencer.Rear silencerLambda probe after the catalytic converter G130 Lambda probe in front of the catalytic converter G39 Middle silencer Pre-silencer Pre-catalytic converterProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Lambda probe II after the catalytic converter G131Main catalytic converterLambda probe II in front of the catalytic converter G108SP48_47Two-probe lambda regulation The pre-catalytic converters age more than the main catalytic converters due to the higher exhaust temperatures. The lambda regulation of the two exhaust gas streams therefore only refers to the precatalytic converters which are arranged nearer to the exhaust manifold. This means that more rapid warming of the lambda probes is achieved after a cold start and the lambda regulation kicks in earlier. If the "lambda probes after the catalytic converter" were to be located after the main catalytic converter then the longer reaction times and possible faults in the main catalytic converter would negatively effect the lambda regulation. The combined system of the pre- and main catalytic converter, lambda probes and engine management means that the limit values for EU4 are already being guaranteed today. The function of two-probe lambda regulation is already described in SSP 30 and generally also applies to this engine.GB35The secondary air systemAn overviewJ220N112A G108G70 G39 BG62V101 J299SP48_41Structure and function The high degree of enrichment of the mixture during the cold start and the warming up phase mean that there is an increased concentration of unburned hydrocarbons in the exhaust gases at these times. This concentration of hydrocarbons cannot be handled by the catalytic converter since: – Blowing in air rear of the outlet valve achieves an increase in the concentration of oxygen in the exhaust gases whereby retrospective oxidation (back burning) of the hydrocarbons and the carbon monoxide takes place. The heat so generated provides additional heat to the catalyser and therefore brings it up to operating temperature more rapidly.–The secondary air system consists of: the required operating temperature of the Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted catalytic converter has not been reached unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by Š KODA AUTO A. S.� for the Motronic J220 – the control unit yet and – a relay for the secondary air pump J299 a mixture of lambda = 1 must be available – motor for the secondary air pump V101 to obtain full conversion. – the secondary air inlet valve N112 – two combination valves A and B36GBSecondary air inlet valve N112Combination valve cylinder bank 1Combination valve cylinder bank 2Air filterSP48_42Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Motor for the secondary with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� air pump V101Note: An extensive description of thesecondary air system can be found in SSP 30.GB37Self-diagnosisThe self-diagnostic function can only be executed along with the VAS 5051 Vehicle Diagnosis, Measurement and Information System. The previously known functions such as: – – – – – – – – interrogating the control unit function interrogating the fault memory undertaking an actuator diagnosis undertaking movement to the home position interrogating the fault memory and deleting it coding the control unit read a measuring value block reading off the readiness codeare integrated into the "Guided search for faults". Note: Further information can be taken from the Operating Manual for the VAS 5051.SP48_63All coloured components of the system are monitored by the self-diagnosis system.G70 G28 G40 G163 G39, G130 G108,G131 J338Protected G42by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�J17 N30, N31, N32 N33, N83, N84 N152 N80 N156 J338 N205 N208 Z19, Z29 Z28, Z30 N112 J299SP48_64G62GatewayG61, G66 G79, G185 F, F47 F3638GBNotesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB39List of Self-Study Programmes published so farNo. Title1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Mono-Motronic Central Locking Anti-Theft Alarm Working with Current Flow Diagrams ŠKODA FELICIA ŠKODA Vehicle Safety Principles of ABS - Not published ABS FELICIA Immobiliser with Transponder Air Conditioning in Vehicles FELICIA Air Conditioning 1.6-ltr. Engine with MPI 1.9-ltr. Naturally Aspirated Diesel Engine Power-Assisted Steering ŠKODA OCTAVIA 1.9-ltr. TDI Engine OCTAVIA Convenience Electronics System OCTAVIA Manual Gearbox 02K/02J 1.6-ltr./1.8-ltr. Petrol Engines Automatic Gearbox Fundamentals Automatic Gearbox 01M 1.9-ltr. 50 kW SDI/1.9-ltr. 81 kW TDI 1.8-ltr. 110 kW turbo petrol engine 1.8-ltr. 92 kW petrol engine OCTAVIA CAN databus OCTAVIA – CLIMATRONIC OCTAVIA – Vehicle Safety OCTAVIA – 1.4-ltr. Engine and Gearbox 002 OCTAVIA – ESP OCTAVIA – 4 x 4 Petrol Engine 2.0-ltr. 85 kW and 88 kW OCTAVIA – Radio/Navigation System ŠKODA FABIA ŠKODA FABIA – Vehicle Electrics ŠKODA FABIA – Power Steering Petrol Engines 1.4-ltr. - 16 V 55/74 kW ŠKODA FABIA – 1.9-ltr. TDI Unit Injection 5-Speed Manual Gearbox 02T and 002 ŠkodaOctavia – Model 2001 Euro On-Board Diagnosis Automatic Gearbox 001 6-Speed Manual Gearbox 02M ŠkodaFabia – ESP Exhaust Emissions Extended Service Interval 1.2-ltr. 3-Cylinder Petrol Engines ŠkodaSuperb; Presentation of the Vehicle Part I ŠkodaSuperb; Presentation of the Vehicle Part II ŠkodaSuperb; V6 Internal Combustion Engine 2.8 litre/142 kWNo. TitleProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not per unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A.For internal use only within the ŠKODA Organisation. All rights reserved. Subject to technical modification. S00.2003.48.20 Technical Status 03/02 GB © ŠKODA AUTO a. s. http://partner.skoda-auto.com❀ This paper has beenmanufactured from chlorine-free bleached cellulose.48