TECHNICAL DOCUMENTATION
SSP 850123 – The 7-speed Double-Clutch Transmission 0AM

This PDF is currently unavailable.
Read document text
Service TrainingSelf Study Program 850123The 7-speed Double-Clutch Transmission 0AMDesign and FunctionVolkswagen Group of America, Inc. Volkswagen Academy Printed in U.S.A. Printed 08/2012 Course Number 850123©2012 Volkswagen Group of America, Inc. All rights reserved. All information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Volkswagen Group of America, Inc. Always check Technical Bulletins and the latest electronic repair information for information that may supersede any information included in this booklet. Trademarks: All brand names and product names used in this manual are trade names, service marks, trademarks, or registered trademarks; and are the property of their respective owners.ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Selector Lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Transmission Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Mechatronic Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Electrohydraulic Control Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Oil Circuit – Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Transmission Management System . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Knowledge Assessment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67NoteImportant!This Self-Study Program provides information regarding the design and function of new models. This Self-Study Program is not a Repair Manual.This information will not be updated. For maintenance and repair procedures, always refer to the latest electronic service information.iiiPage intentionally left blankIntroductionThe New 7-Speed Double-Clutch Transmission from VolkswagenThe 7-speed double-clutch transmission 0AM is based on the 02E DSG transmission. It offers the same comfort and shifting characteristics of the 02E DSG. It has been designed for engines with a torque of up to 184 lb/ft (250 Nm) of torque. The DSG transmission economy is on a par with manual transmission vehicles. The DSG transmission has succeeded in reducing fuel consumption below that of manual transmissions using technical innovations. This reduction in fuel consumption makes a significant contribution towards lowering emissions. In this SSP , you will learn how the new 0AM double-clutch transmission functions and the technical highlights that help to reduce fuel consumption. We hope you enjoy reading it.Application in the Jetta HybridAlthough Volkswagen has used this transmission in vehicles for many years, the first application for the North American market is the 2013 Jetta Hybrid. Some aspects of this SSP are different for hybrid applications, and this SSP does not cover those differences. Please refer to ElsaWeb for the specific changes for use in the Jetta Hybrid.1IntroductionThe new 0AM DSG is the: • First transverse 7-speed transmission • First double-clutch transmission with dry double clutchMechatronic UnitS390_060Double ClutchThe dry double clutch has an extensive impact on the entire transmission concept. In comparison with the directshift transmission 02E, efficiency has been considerably improved. This improved efficiency makes a significant contribution towards lowering consumption and emissions.2IntroductionDesign Features• Modular design of the transmission: The clutch, mechatronic unit and transmission each form one unit • Dry double clutch • Separate oil circuit, mechatronic unit and mechanical transmission, with lifetime fillings • Seven speeds on four shafts • No oil/water heat exchangerMechatronic UnitDouble ClutchS390_003Technical DataDesignation Weight Torque Gears Spread Operating Mode Transmission Fluid Volume Mechatronic Unit Fluid Volume0AM Approx. 154 lb (70 kg) including clutch 184 ft lbs (250 Nm) Seven Forward Speeds, One Reverse =Ggear 8.1 Automatic and Tiptronic Modes 1.7L - G 052 171 1.0L Central Hydraulic/Power Steering Box Fluid G 004 0003Selector LeverActuationThe selector lever is the same as in normal automatic transmission vehicles. The double-clutch transmission also offers the option of shifting using Tiptronic. As with automatic transmission vehicles, the selector lever has with a selector lever lock and an ignition key withdrawal lock. The selector lever positions are: P - Park To move the selector lever from this position, the ignition must be ON and the foot brake must be depressed. The release button on the selector lever must also be pressed. R - Reverse Gear The release button must be pressed to engage this gear. N - Neutral Position In this position, the transmission is in neutral. If the selector lever is set to this position for a long time, the foot brake must be depressed again to move it from this position. D - Drive Position In this drive position, the forward gears are shifted automatically. S - Sport Automatic gear selection is carried out according to a "sporty" characteristic curve, which is stored in the control module.Release ButtonS390_0054Selector LeverDesign of the Selector LeverE313 Selector Lever Hall sensors in the selector lever register the selector lever position and make this information available to the mechatronic unit via the CAN bus. N110 Shift Lock Solenoid The solenoid locks the selector lever in the "P" and "N" positions. The solenoid is controlled by the J587 Selector Lever Sensor System Control Module. F319 Selector Lever Park Position Lock Switch If the selector lever is in the "P" position, the signal is sent to the J527 Steering Column Electronics Control Module. The control module requires this signal to control the ignition key withdrawal lock.Locking Pin Latch "P"F319E313Locking Pin Latch "N"N110S390_007Hall Senders for Detecting the Selector Lever Position5Selector LeverN110 Shift Lock SolenoidHow It Works: Selector Lever Locked in "P" Position If the selector lever is set to "P", the locking pin is located in locking pin latch "P". This prevents the locking lever from being moved unintentionally.N110 Compression SpringLocking Pin Latch for "P"Locking PinS390_008Selector Lever Released: After switching on the ignition and actuating the foot brake, the J587 Selector Lever Sensor System Control Module supply the N110 Shift Lock Solenoid with current. As a result of this, the locking pin is withdrawn from the locking pin latch "P". The selector lever can now be moved to the drive position.S390_009Selector Lever Locked in "N" Position If the selector lever is set to the "N" position for longer than 2 sec., the control unit supplies the solenoid with current. As a result of this, the locking pin is pressed into locking pin latch "N". The selector lever can no longer be unintentionally moved into a gear. The locking pin is released when the brake is actuated.Locking Pin Latch for "N"S390_0106Selector LeverEmergency Release If the voltage supply to the N110 Shift Lock Solenoid fails, the selector lever cannot be moved because selector lever lock "P" remains activated in the event of a power failure. By mechanically "pressing in" the locking pin with a narrow object, the lock can be released and the selector lever can be "emergency released" to the "N" position. The vehicle can be moved again.S390_0117Selector LeverIgnition Switch Key Lock Solenoid The ignition key withdrawal lock prevents the ignition key from being turned back to the removal position if the parking lock is not engaged.N376It functions electromechanically and is controlled by the J527 Steering Column Electronics Control Module. The J527 detects the open switch. The N376 Ignition Switch Key Lock Solenoid is not supplied with current. The compression spring in the solenoid pushes the locking pin into the release position.S390_012How It Works: With the selector lever in park position the ignition is switched off. If the selector lever is set to the park position, the F319 Selector Lever Park Position Lock Switch is opened.Retaining Lug Compression Spring"Ignition Off" Locking PinS390_0138Selector LeverHow It Works: Selector lever in drive position the ignition is switched on. If the selector lever is set to the drive position, the F319 Selector Lever Park Position Lock Switch is closed. The steering column electronics control unit then supplies the N376 Ignition Switch Key Lock Solenoid with current. The locking pin is pushed into the locked position because the solenoid overcomes the force of the compression spring. In the locked position, the locking pin prevents the ignition key from being turned back and withdrawn. Only when the selector lever is pushed into the park position does the selector lever locked in position "P" switch open and the control unit switches off the current supply to the solenoid. The locking pin is then pressed back by the compression spring. The ignition key can be turned further and can be removed."Ignition On"N376S390_0149Transmission DesignBasic PrincipleIn principle, the double-clutch transmission consists of two independent halves. In terms of function, each half is designed as a manual transmission. A clutch is assigned to each half. The two clutches are dry clutches. They are opened and closed and controlled by the mechatronic unit depending on the gear to be shifted. Gears 1, 3, 5 and 7 are shifted via clutch K1 via gear train half 1 and output shaft 1. Gears 2, 4, 6 and reverse gear are actuated via clutch K2 and gear train half 2 and output shafts 2 and 3. One gear train half is always connected. The next gear can already be shifted in the other gear train half, because the clutch for this gear is still open. A conventional, manual transmission synchronizer and shift unit is assigned to each gear.Basic SchematicOutput Shaft 2 Output Shaft 3 Gear Train Half 2 Drive Shaft 2R 6 4 2 K2 K17531Engine TorqueDrive Shaft 1Output Shaft 1 Gear Train Half 1S290_01510Transmission DesignTorque InputTorque is transferred from the dual-mass flywheel, which is secured to the crankshaft, to the double clutch. The dual-mass flywheel is equipped with inner teeth that engage in the outer teeth on the double clutch carrier ring. From there, the torque is transmitted to the double clutch.Carrier RingDrive Shafts 1 and 2Outer TeethInner TeethDouble ClutchDual-Mass FlywheelS390_06411Transmission DesignDouble Clutch and Torque CurveThe double clutch is located in the bell housing. It consists of two conventional clutches, which combined form a double clutch. During the remainder of this SSP , the clutches are referred to as K1 and K2. Clutch K1 transfers the torque to drive shaft 1 via splines. From drive shaft 1, the torque for gears 1 and 3 is transferred to output shaft 1, and the torque for gears 5 and 7 is transferred to output shaft 2. Clutch K2 transfers the torque to drive shaft 2 via splines. It transfers the torque for gears 2 and 4 to output shaft 1 and the torque for 6th gear and reverse gear to output shaft 2. Using the reverse gear intermediate gear R1, the torque is then passed on to reverse gear R2 on output shaft 3. All three output shafts are connected to the differential final drive gear.Dual-Mass Flywheel Clutch K2 Output Shaft 3 Clutch K1 Output Shaft 2Drive Shaft 1Drive Shaft 2 Output Shaft 1Final Drive Gear 1 … 7 = 1st to 7th gears R1 = reverse gear intermediate gear R2 = reverse gear DifferentialS390_01612Transmission DesignDouble Clutch Drive PlateFrom the carrier ring, the torque is transferred to the drive plate in the double clutch. For this to take place, the carrier ring and drive plate are joined firmly together. The drive plate is mounted on drive shaft 2 as an idler gear.How It Works:Carrier RingIf one of the two clutches is actuated, the torque is transferred from the drive plate onto the relevant clutch plate and onwards onto the corresponding drive shaft.Carrier RingS390_065Drive PlateDrive Shafts 1 and 2Dual-Mass FlywheelClutch K2S390_067Clutch K113Transmission DesignClutchesTwo independent, dry clutches operate in the double clutch. They each transfer the torque to one gear train half. Two clutch positions are possible: • When the vehicle is stopped and idling, both clutches are open. • During vehicle operation, only one of the two clutches is ever closed. Clutch K1Clutch K1 conducts the torque for gears 1, 3, 5 and 7 to drive shaft 1.Clutch K1 Not ActuatedDrive Shaft 1S390_01714Transmission DesignHow It Works: To actuate the clutch, the engaging lever presses the engagement bearing onto the diaphragm spring. At several contact points, this compression movement is transformed into a tension movement. As a result, the pressure plate is pulled onto the clutch plate and the drive plate. The torque is then transferred to the drive shaft. The engaging lever is actuated via N435 Sub-Transmission 1 Valve 3 by the hydraulic clutch actuator for K1.Diaphragm SpringClutch K1 ActuatedEngagement BearingPressure PlateS390_066Drive PlateDiaphragm SpringClutch PlateEngaging LeverS390_08715Transmission DesignClutch K2Clutch K2 transfers the torque for gears 2, 4, 6 and R to drive shaft 2.Drive Shaft 2S390_01816Transmission DesignHow It Works:Clutch K2 If the engaging lever is actuated, the engagement bearing presses against the pressure plate diaphragm spring. Because the diaphragm spring is supported by the clutch housing, the pressure plate is pressed against the drive plate and the torque is transferred onto drive shaft 2. The engaging lever is actuated via N439 Sub-Transmission 2 Valve 3 by the hydraulic clutch actuator for K2.Drive Plate Pressure Plate Support PointClutch K2 ActuatedDiaphragm SpringEngagement BearingClutch PlateEngaging LeverS390_08817Transmission DesignDrive ShaftsThe drive shafts are located in the transmission housing. Each drive shaft is connected to a clutch via splines. These transfer the engine torque onto the output shafts according to the gear which is engaged. Drive shaft 2 is hollow. Drive shaft 1 runs through hollow drive shaft 2. Ball bearings are mounted in the transmission case.S390_046Drive Shaft 1Drive Shaft 2SplineBall BearingS390_01918Transmission DesignDrive Shaft 2Due to its installation position, we will cover drive shaft 2 before drive shaft 1.Gear for G612 Bearing4th/6th GearsS390_0202nd/R GearsDrive shaft 2 is a hollow shaft. It is connected to K2 via splines. Drive shaft 2 is used to shift gears 2, 4, 6 and R. To record the transmission input speed, this shaft has the gear for G612 Transmission Input Speed Sensor 2.Drive Shaft 1BearingG6321st Gear5th Gear 3rd Gear7th GearS390_021Drive shaft 1 is connected to clutch K1 via splines. It is used to shift gears 1, 3, 5 and 7 . To record the transmission input speed, this shaft has the impulse wheel for G632 Transmission Input Speed Sensor 1.Please note that a strong magnet may destroy the impulse wheel for drive shaft 1.19Transmission DesignOutput ShaftsThe transmission has three output shafts. Depending on the gear which is engaged, the engine torque is transferred from the drive shafts to the output shafts. An output gear is located on each output shaft. Installation Position in the Transmission(View from the left – shown elongated)S390_023Output Shaft 11st Gear3rd Gear4th Gear2nd GearOutput GearBearing Bearing Sliding Sleeve, Gears 1/3 Sliding Sleeve, Gears 2/4S390_022The following are located on output shaft 1: • The selector gears for gears 1, 2 and 3; the 3 gears are 3x’s synchromeshed. • The selector gear for 4th gear; the 4th gear is 2x’s synchromeshed.20Transmission DesignInstallation Position in the Transmission(View from the left – shown elongated)S390_025Output Shaft 2R Gear 1 5th Gear 7th Gear 6th Gear R Gear 2 Output GearSliding Sleeve, Gears 5/7Sliding Sleeve, Gears 6/RS390_024The following are located on output shaft 2: • The 2-fold synchromeshed selector gears for gears 5, 6 and 7, and • The intermediate gears R gear 1 and R gear 2 for reverse gear.21Transmission DesignOutput Shaft 3Installation Position in the Transmission(View from the left – shown elongated)Parking Lock GearGear Wheel for R GearS390_027Bearing Output Gear BearingSliding SleeveS390_026The following are located on output shaft 3: • The 1-fold synchromeshed selector gear for R gear • The parking lock gear22Transmission DesignDifferentialInstallation Position in the Transmission(View from the left – shown elongated)Final Drive GearS390_029S390_028The differential transfers the torque onwards to the vehicle wheels via the drive shafts.23Transmission DesignParking LockA parking lock is integrated into the DSG to ensure that a parked vehicle does not roll away. The locking pin is engaged purely mechanically via a Bowden cable between the selector lever and the parking lock lever on the transmission. The Bowden cable is used exclusively to actuate the parking lock.Connection Ball for Parking Lock Bowden CableHold-Down DeviceDetent Spring Locking Pin Actuation PinPre-Tensioning SpringReturn Spring for Locking PinParking Lock GearS390_03024Transmission DesignFunctionParking Lock Not Actuated, (Selector Lever Position R, N, D, S) When the parking lock is not actuated, the cone of the actuation pin lies on the holding-down device and the locking pin. The parking lock is held in the non-actuated position by a locking device.Actuation Pin Locking Pin Detent SpringHold-Down DeviceParking Lock Sctuated, Locking Pin Not Engaged (Selector Lever Position P) By actuating the parking lock, the cone of the actuation pin is pressed against the hold-down device and the locking pin. As the hold-down device is stationary, the locking pin moves down. If it encounters a tooth on the parking lock gear, the pretensioning spring is tensioned. The actuation pin is held in this position by the locking device.S390_061Locking DevicePre-Tensioning Spring, TensionedS390_062Parking Lock Actuated, Locking Pin Engaged (Selector Lever Position P) (Locking Pin Engaged) If the vehicle continues to move, the parking lock gear also rotates. As the actuation pin is pre-tensioned, it automatically pushes the locking pin into the next tooth space on the parking lock gear.Tooth of Locking Pin Engaged in Parking Lock GearPre-Tensioning Spring, Relaxed Actuation Pin in End PositionS390_06325Transmission DesignGear SynchronizationA synchromesh with locking pieces is used for all gears to synchronize the different speeds when changing gears. Depending on the shifting load, the gears are synchronized between one and three times.Gear 1st to 3rd 4th 5th to 7th RSynchromesh Three synchronizers Two synchronizers One synchronizer One synchronizerSynchronizer Ring Material Brass with molybdenum coating Brass with molybdenum coating Brass with molybdenum coating Brass with molybdenum coatingThe figure shows the synchromesh design for 2nd, 4th and R gears.Outer ring (intermediate ring) Selector ForkIntermediate Ring Firmly Connected (Welded)Synchronizer Ring (inner) Selector gear 2nd gear Synchronizer Ring (outer) Synchronising Hub Sliding Sleeve Synchronizer Ring (outer)Locking piecesS390_081Clutch Splines Synchronizer Ring (inner)Selector Gear 4th GearSliding SleeveSelector Gear R Gear Synchronizer Ring Locking Pieces Synchronising HubS390_08226Transmission DesignPower Transmission in the GearsTorque is transmitted into the transmission by either clutch K1 or K2. Each clutch drives a drive shaft. Drive shaft 1 is driven by clutch K1 and drive shaft 2 is driven by clutch K2. Power is transmitted to the differential via: • output shaft 1 for gears 1, 2, 3, and 4, • output shaft 2 for gears 5, 6 and 7, and • output shaft 3 for reverse gear and the parking lock.S390_033S390_0341st GearClutch K1 Drive Shaft 1 Output Shaft 1 DifferentialR GearClutch K2 Drive Shaft 2 Output Shaft 3 DifferentialThe change in rotational direction for reverse gear is carried out by output shaft 3.For greater clarity, power transmission is shown schematically in "elongated" form.27Transmission Design2nd GearClutch K2 Drive Shaft 2 Output Shaft 1 DifferentialS390_0353rd GearClutch K1 Drive Shaft 1 Output Shaft 1 DifferentialS390_0364th GearClutch K2 Drive Shaft 2 Output Shaft 1 DifferentialS390_03728Transmission Design5th GearClutch K1 Drive Shaft 1 Output Shaft 2 DifferentialS390_0386th GearClutch K2 Drive Shaft 2 Output Shaft 2 DifferentialS390_0397th GearClutch K1 Drive Shaft 1 Output Shaft 2 DifferentialS390-04029Mechatronic ModuleJ743 DSG Transmission MechatronicThe mechatronic unit controls all transmission functions. It combines the electronic control unit and the electrohydraulic control unit into a single component. The mechatronic unit is an autonomous unit. It has a separate oil circuit, which is independent of the oil circuit for the mechanical transmission.The advantages of this autonomous, compact unit are: • All sensors (except one) and actuators are contained in the mechatronic unit. • The hydraulic fluid is specifically adapted to the requirements of the mechatronic unit. • Due to the separate oil circuit, no foreign material from the mechanical transmission enters into the mechatronic unit. • Good low-temperature behavior, as no compromise has to be made with the requirements of the transmission in terms of viscosity behavior.Mechatronic UnitS390_04130Mechatronic ModuleThe electornic control unit is the central transmission control unit. All sensor signals and all signals from other control units come together here, and all actions are performed and monitored by it. Eleven sensors are integrated into the electronic control unit; only the G182 Transmission Input Speed Sensor is located outside of the control unit. The electronic control unit hydraulically controls and regulates eight solenoid valves for shifting the seven gears and for actuating the clutch. The electronic control unit learns (adapts) the positions of the clutches and the positions of the gear selectors when a gear is engaged and takes what has been learned into consideration for operation of these components.G490 Gear Position Distance Sensor 4 (Gears 6/R) G612 Transmission Input Speed Sensor 2Sensor LocationsG489 Gear Position Distance Sensor 3 (Gears 5/7)G632 Transmission Input Speed Sensor 1Vehicle connectorElectronic Control Unit with Integrated Sensor SystemG487 Gear Position Distance Sensor 1 (Gears 4/2) G182G510 Temperature Sensor in Control ModuleG488 Gear Position Distance Sensor 2 (gears 1/3)S390_042G270 Hydraulic Pressure SensorG617 Clutch Pedal Position Sensor 1 for K1 G618 Clutch Pedal Position Sensor 2 for K2S390_08331Electrohydraulic Control UnitElectrohydraulic Control UnitThe electrohydraulic control unit is integrated into the mechatronic module. It generates the oil pressure which is required to shift the gears and to actuate the clutches. Oil Pressure Generation and Control The oil pressure is generated by the hydraulic pump motor. An oil pressure accumulator ensures that sufficient oil pressure is always present at the solenoid valves.Oil Pressure Accumulator Electrohydraulic Control UnitTo Clutch K1Hydraulic PumpTo Clutch K2Valve 3 in Gear Train Half 1 N435 Clutch Valve K1N438 Sub-Transmission 2 Valve 2 Gear Selector Valve 6/R N440 Sub-Transmission 2 valve 4 Gear Train Half Pressure regulator N439 Sub-Transmission 2 Valve 3 Clutch Valve K2 N437 Sub-Transmission 2 Valve 1 Gear Selector Valve 2/4N434 Sub-Transmission 1 Valve 2 Gear Selector Valve 5/7 Gear Selector ValveN436 Sub-Transmission 1 Valve 4 Gear Train Half Pressure RegulatorN433 Sub-Transmission 1 Valve 1 Gear Selector Valve 1/3 Motor for Hydraulic Pump V401S390_04332Oil Circuit - Hydraulic SystemOil CircuitThe double clutch transmission operates with two independent oil circuits using two different oils: • Oil circuit for mechanical transmission • Oil circuit for mechatronic module Each oil circuit contains a specific oil.Mechatronic Module Oil Circuit for Mechanical TransmissionS390_080Oil Circuit - Mechanical Transmission The oil supply to the shafts and gears of the mechanical transmission is the same as in a normal manual transmission. The oil volume in the mechanical transmission is 1.7 L.Oil Circuit - Mechatronic Module The oil supply for the mechatronic unit is separate from the oil circuit for the mechanical transmission. An oil pump delivers pressurized oil so that the hydraulic mechatronic unit components can function. The oil volume in the mechatronic unit is 1.1 L.For the volumes and capacities, always refer to the service information33Oil Circuit - Hydraulic SystemOil Circuit Flow ChartBasic Oil CircuitPressure Limiting Valve Filter V401 Hydraulic Pump Motor Pressure Accumulator Hydraulic Pressure SenderNon-Return Valve Hydraulic PumpS390_ 09834Oil Circuit - Hydraulic SystemHydraulic PumpThe hydraulic pump unit is located in the mechatronic Hydraulic Pump module. It consists of a hydraulic pump and an electric motor. The motor for the hydraulic pump is a brushless DC motor. It is actuated by the mechatronic unit’s electronic control unit depending on pressure requirements. It drives the hydraulic pump through a coupling.S390_043V401 Hydraulic Pump MotorThe hydraulic pump operates just like a gear pump. It pulls in hydraulic oil and pumps it into the oil circuit at a pressure of approximately 70 bar. The hydraulic oil is pumped from the intake side to the pressure side between the walls of the pump housing and the tooth gaps.Intake SideHousingPressure SideDriving GearS390_07135Oil Circuit - Hydraulic SystemV401 Hydraulic Pump MotorDesign Like conventional, smaller DC electric motors, the brushless DC motor has a stator and a rotor. While the stator consists of permanent magnets and the rotor of electromagnets in the conventional, smaller electric motor, the opposite is true in the case of the brushless DC motor. The rotor consists of six permanent magnet pairs. The stator has six electromagnet pairs.Rotor with Permanent Magnets Torque to the Hydraulic pumpElectrical Connection Electromagnet Pole PairsHow It WorksStatorS390_085In the conventional DC motor, commutation (current direction change-over) takes place via ring contacts. Commutation in the brushless DC motor is carried out by the mechatronic unit's electronic control unit and is contact-free. The stator coils are actuated to that a rotating magnetic field occurs in the stator coils. The rotor follows this magnetic field and is rotated. Thanks to contact-free commutation, the DC motor runs entirely wear-free, with the exception of bearing wear.StatorRotorS390_08936Oil Circuit - Hydraulic SystemElectrical ActuationThe mechatronic unit controls switching between the individual poles to ensure smooth rotational movement. This changes the magnetic field. As a result, the rotor is rotated.The schematic shows the design of the circuit using the example of a wound coil.Mechatronic Unit Control UnitSupply Voltage 2nd Phase 1st Phase 3rd PhaseWound CoilS390_086Legend 1st phase – positively switched 2nd phase – negatively switched 3rd phase - open37Oil Circuit - Hydraulic SystemG270 Hydraulic Pressure Sensor and Pressure Limiting ValveThe hydraulic pump pumps the hydraulic oil through the filter towards the pressure limiting valve, the pressure accumulator and the hydraulic pressure sender. When the hydraulic oil pressure at the pressure limiting valve and the hydraulic pressure sender reaches approximately 70 bar, the control unit turns the electric motor and hydraulic pump off. The bypass ensures that the system functions if the filter channel is clogged.Hydraulic Pressure SenderPressure Limiting ValveS390_100Pressure AccumulatorPressure Accumulator The pressure accumulator is designed as a gas pressure accumulator. It provides the hydraulic system with oil pressure when the hydraulic pump is turned off. Its storage volume is 0.2 litres.S390_09638Oil Circuit - Hydraulic SystemOil Circuit Flow ChartWorking Pressure Return Controlled Working Pressure KS = Clutch Safety ValveKS KSGear Selector 1 - 3Clutch Actuator K1 Gear Selector 4 - 2 Gear Selector 5 - 7Gear Selector 6 - RClutch Actuator K2S390_048LegendN433 Valve 1 in Gear Train Half 1 N434 Valve 2 in Gear Train Half 1 N435 Valve 3 in Gear Train Half 1 N436 Valve 4 in Gear Train Half 1N437 Valve 1 in Gear Train Half 2 N438 Valve 2 in Gear Train Half 2 N439 Valve 3 in Gear Train Half 2 N440 Valve 4 in Gear Train Half 2The clutch safety valves enable the clutches to be drained and therefore opened in the event of a fault.39Oil Circuit - Hydraulic SystemSolenoid ValvesGear Train Half Pressure Control Solenoid Valves The gear train half pressure control solenoid valves control the oil pressure for gear train halves 1 and 2. If a fault is detected in a gear train half, the pressure control solenoid valve can shut off the corresponding gear train half.Gear Train Half 2 Pressure Control ValveS390_101Gear Selector Solenoid Valves The gear selector solenoid valves control the volume of oil to the gear selectors. Each gear selector shifts two gears. If no gear is engaged, the gear selectors are held in the neutral position via oil pressure. In selector lever position "P" and when the ignition is switched off, 1st gear and reverse gear are engaged.Gear Train Half 1 Pressure Control Valve Gears 5/7 Gears 6/RGears 2/4S390_102Clutch Actuator Solenoid Valves The clutch actuator solenoid valves control the volume of oil to the clutch actuators. The clutch actuators actuate clutches K1 and K2. When not supplied with current, the solenoid valves and the clutches are open.Gears 1/3 K1K2S390_10340Oil Circuit - Hydraulic SystemShifting the GearsAs with conventional manual transmissions, the gears are shifted using selector forks. Each selector fork shifts two gears. The selector forks are mounted on both sides in the transmission housing.Selector Fork Gears 5/7Selector Fork Gears 6/RSelector Fork Gears 1/3Selector Fork Gears 2/4S390_05841Oil Circuit - Hydraulic SystemShifting the GearsWhen changing gears, the selector forks are moved by the gear selectors integrated into the mechatronic unit. Gear Selectors and Selector Forks The gear selector piston is connected to the selector fork. To change gears, oil pressure is applied to the gear selector piston. When it moves, it also moves the selector fork and the sliding sleeve. The sliding sleeve actuates the synchronising hub and the gear is engaged.Gear Selector Gears 1 and 3 Gear Selector Movement Sensor Gear Selector Cylinder Gear Selector Gears 5 and 7 Gear Selector Gears 6 and RS390_107Gear Selector Gears 2 and 4Gear Selector PistonPermanent MagnetSliding Sleeve Selector Fork Synchronising HubS390_056The mechatronic unit detects the new position of the selector fork via the permanent magnet and the gear selector movement sensor.42Oil Circuit - Hydraulic SystemGear ChangesJust like the 02E DSG, the selector forks are actuated hydraulically. To change the gears, the mechatronic unit actuates the correct gear selector solenoid valve.How It Works This is an example of changing into 1st gear:Initial Position The gear selector piston is held in neutral position "N" via the oil pressure controlled by N433 SubTransmission 1 Valve 1 for gears 1 and 3. No gear is engaged. N436 Sub-Transmission 1 Valve 4 controls the oil pressure in gear train half 1.Mechatronic UnitN436N433 Gear Selector Cylinder Gear Selector PistonPiston ChamberSelector Fork Sliding SleeveS390_05743Oil Circuit - Hydraulic SystemChanging to 1st GearTo change to 1st gear, the gear selector valve increases the oil pressure in the left piston chamber and pushes the gear selector piston to the right. As the selector fork and the sliding sleeve are connected to the gear selector piston, they also move to the right. Because of the movement of the sliding sleeve, 1st gear is engaged.Mechatronic UnitN433 SubTransmission 1 Valve 4Gear Selector Cylinder Gear Selector PistonPiston Chamber Selector ForkSliding SleeveS390_09744Oil Circuit - Hydraulic SystemClutch ActuatorsClutches K1 and K2 are actuated hydraulically. To achieve this, the mechatronic unit contains a clutch actuator for each clutch. A clutch actuator consists of a clutch actuator cylinder and a clutch actuator piston. The clutch actuator piston actuates the clutch engaging lever. The clutch actuator piston is equipped with a permanent magnet, which is required by the clutch travel sender to detect the piston position. To prevent detection of the piston position from being impaired, the actuator cylinder and the actuator piston are not magnetic.Permanent Magnet Clutch Actuator Cylinder Clutch Actuator K1BootClutch Actuator PistonPiston RodDust Protection BellowsSupport RingGuide Ring Clutch Actuator K2 Engaging LeverS390_09245Oil Circuit - Hydraulic SystemClutch OperationTo actuate the clutches, the mechatronic electronic control unit actuates the solenoid valve • N435 Sub-Transmission 1 Valve 3 for clutch K1 and • N439 Sub-Transmission 2 Valve 3 for clutch K2. How It Works Actuation of K1 is shown here as an example. Clutch Not Actuated The clutch actuator piston is in the resting position. The N435 is open in the return flow direction. The oil pressure from the N436 Sub-Transmission 1 Valve 4 flows into the mechatronic unit oil reservoir.N435Clutch Actuator K1 in Resting PositionS390_09346Oil Circuit - Hydraulic SystemClutch Actuated If clutch K1 is to be actuated, the N435 SubTransmission 1 Valve 3 is actuated by the electronic control unit. When actuated, it opens the oil channel to the clutch actuator, and oil pressure is built up at the rear of the clutch actuator piston. The clutch actuator piston moves and actuates the K1 clutch engaging lever. Clutch K1 is closed. The control unit receives a signal regarding the precise position of the clutch via G167 Rear Infrared Sensor. The speed difference between the transmission input speed and drive shaft speed (clutch slip), is controlled by N435 by controlling the oil pressure between the clutch actuator and the return flow.N435Clutch Actuator K1 ActuatedS390_09447Transmission Management SystemOverview of the SystemSensors J743 DSG Transmission MechatronicG182 Transmission Input Speed SensorG632 Transmission Input Speed Sensor 1 G612 Transmission Input Speed Sensor 2G617 Clutch Pedal Position Sensor 1 G618 Clutch Pedal Position Sensor 2G487 Gear Position Distance Sensor 1 G488 Gear Position Distance Sensor 2 G489 Gear Position Distance Sensor 3 G490 Gear Position Distance Sensor 4G270 Hydraulic Pressure SensorG510 Temperature Sensor in Control ModuleE389 Steering Wheel Tiptronic SwitchDiagnostic Connector48Transmission Management SystemCANJ285 Instrument Cluster Control Module E313 Selector LeverActuatorsV401 Hydraulic Pump MotorN435 Sub-Transmission 1 Valve 3 N439 Sub-Transmission 2 Valve 3N436 Sub-Transmission 1 Valve 4 N440 Sub-Transmission 2 Valve 4N433 Sub-Transmission 1 Valve 1 N434 Sub-Transmission 1 Valve 2 N437 Sub-Transmission 2 Valve 1 N438 Sub-Transmission 2 Valve 2S390_05349Transmission Management SystemSensorsG617 Clutch Pedal Position Sensor 1, G618 Clutch Pedal Position Sensor 2 The clutch pedal position sensors are located in the mechatronic unit above the clutch actuators. The double clutch control system requires reliable and precise recording of the current clutch actuation status. For this reason, contact-free sensor technology is used to record clutch travel. Contact-free position recording increases the reliability of the sensor functions. Measured value falsification caused by wear and vibrations is avoided.G617/G618S390_050Signal Use The control unit requires these signals to control the clutch actuators.Effects of Signal Failure If G617 fails, transmission path 1 is shut off. Gears 1, 3, 5 and 7 can no longer be engaged. If G618 fails, gears 2, 4, 6 and R can no longer be engaged.50Transmission Management SystemClutch Pedal Position SensorsDesign A clutch pedal position sensor consists of: • The primary coil is wound around an iron core • Two secondary evaluation coils • A permanent magnet, located on the clutch actuator piston, and • The sensor electronics How It Works An alternating voltage is applied to the primary coil and a magnetic field is built up around the iron core. If the clutch is actuated, the clutch actuator piston moves through the magnetic field with the permanent magnet. Voltage is induced in the secondary evaluation coils. The level of the voltage induced in the left and right evaluation coils depends on the position of the permanent magnet. The sensor electronics detect the position of the permanent magnet and the position of the clutch actuator piston by the level of the voltage in the left and right evaluation coils.Primary Coil Secondary Evaluation CoilIron CoreApplied Alternating VoltageEvaluation Voltage Clutch Actuator Piston Permanent MagnetSensor ElectronicsS390_09151Transmission Management SystemG182 Transmission Input Speed SensorThe transmission input speed sensor is a Hall sensor that is inserted into the transmission housing. It is the only sensor located outside of the mechatronic unit. It electronically scans the starter ring gear and records the transmission input speed. The transmission input speed is identical to the engine speed.G182S390_073Signal Use The control unit requires the transmission input speed signal to control the clutches and to calculate slip. It compares the signals from the G182 before the clutches with the signals from G612 and G632 Transmission Input Speed Sensor 1 and 2, which transmit speed signals from the drive shafts.Effects of Signal Failure The control unit uses the engine speed signal as a substitute signal. It obtains this signal from the engine control unit over the CAN bus.52Transmission Management SystemG632 Transmission Input Speed Sensor 1 G612 Transmission Input Speed Sensor 2Both input speed sensors are Hall sensors that are located in the mechatronic unit. • G632 scans an impulse wheel located on drive shaft 1. From this signal, the control unit calculates the speed of drive shaft 1. • G612 scans a gear on drive shaft 2. From this signal, the control unit calculates the speed of drive shaft 2.G632G612S390_049Signal Use The speed signals from drive shafts 1 and 2 are used by the control unit to control the clutch and to calculate clutch slip.Effects of Signal Failure If G632 fails, gear train half 1 is shut off. The vehicle can then only be driven in gears 2, 4, 6 and R. If G612 fails, gear train half 2 is shut off. The vehicle can then only be driven in gears 1, 3, 5 and 7 .53Transmission Management SystemG510 Temperature Sensor in Control ModuleThe temperature sensor is located directly in the mechatronic unit's electronic control unit. Hot hydraulic oil constantly flows around the control unit, heating it. Severe heating may impair the functions of the electronics.G510S390_074Signal Use The temperature sensor’s signal is used to check the mechatronic unit's temperature. At a temperature of 139 °C, engine torque will be reduced.Effects of Signal Failure In case of signal failure, the control unit uses an internally available substitute value.54Transmission Management SystemG270 Hydraulic Pressure SensorThe hydraulic pressure sensor is integrated into the mechatronic unit hydraulic oil circuit. It is a diaphragm pressure sender.G270S390_075Signal Use The control unit uses the signal to control the motor for the V401 Hydraulic Pump Motor. At a hydraulic oil pressure of approximately 60 bar, the motor is shut off according to the pressure sensor signal, and is switched on again at approximately 40 bar.Effects of Signal Failure If the signal fails, the motor for hydraulic pump runs continuously. The hydraulic pressure is determined by the pressure control valve.55Transmission Management SystemG487 to G490 Gear Position Distance Sensor 1 - 4The gear selector movement sensors are located in the mechatronic unit. In combination with the solenoids on the selector forks, the sensors generate a signal that the control module uses to determine the precise position of the gear selectors.G490G489G487G488S390_051Signal Use The control unit requires the precise position of the gear selectors to control the gear selectors for changing gears.Effects of Signal Failure If a movement sensor fails, the control module cannot detect the position of the corresponding gear selector. As a result, the control unit is unable to recognise whether or not a gear has been changed using the gear selector and the selector fork. To prevent damage to the transmission, half of the transmission with this failure will be disabled.56Transmission Management SystemE313 Selector LeverThe selector lever sensor system and the control system for the selector lever lock solenoid are integrated into the selector lever. The selector lever positions are detected by Hall sensors, which are integrated into the selector lever sensor system. The selector lever position signals and the Tiptronic signals are transmitted over the CAN bus to the mechatronic unit and to the control unit in the dash panel insert. Signal Use Based on the signals, the control unit detects the selector lever positions. It uses the signals to implement the driver D-R-S or Tiptronic command and to control starter release. Effects of Signal Failure If the control unit detects no selector lever position, both clutches are opened.Hall Sensors for Tiptronic PositionS390_052Hall Sensors for Detecting the Selector Lever Position57Transmission Management SystemActuatorsClutch Actuator Solenoid Valves N435 Sub-Transmission 1 Valve 3, N439 Sub-Transmission 2 Valve 3 The clutch actuator solenoid valves are located in the mechatronic unit's hydraulic module. They are actuated by the electronic transmission control unit. They are used to control the oil volume for actuating the clutches. • N435 controls the oil volume for clutch K1 • N439 controls the oil volume for clutch K2N435N439S390_076Effects of Signal Failure If a solenoid valve fails, that half of the transmission will be disabled.58Transmission Management SystemGear Train Half Pressure Control Valves N436 Sub-Transmission 1 Valve 4, N440 Sub-Transmission 2 Valve 4 Both sub-transmission valves are solenoid valves, and are located in the mechatronic unit hydraulic module. Valve 4 in gear train half 1 controls the hydraulic oil pressure to the gear selectors and to the clutch actuator in gear train half 1. Gear train half 1 is used to shift gears 1, 3, 5 and 7 . Valve 4 in gear train half 2 controls the hydraulic oil pressure to the gear selectors and to the clutch actuator in gear train half 2.N440N436S390_077Effects of Signal Failure If one solenoid valve fails, that half of the trnamsisison will be disabled, and only the gears assigned to the other transmission half can be engaged.59Transmission Management SystemGear Selector Solenoid ValvesN433 Sub-Transmission 1 Valve 1, N434 Sub-Transmission 1 Valve 2, N437 Sub-Transmission 2 Valve 1, N438 Sub-Transmission 2 Valve 2 The gear selector solenoid valves are located in the mechatronic unit's hydraulic module. They are used by the transmission control unit to control the oil volume to the gear selectors and for changing gears. • N433 Sub-Transmission 1 Valve 1 • N434 Sub-Transmission 1 Valve 2 • N437 Sub-Transmission 2 Valve 1 • N438 Sub-Transmission 2 Valve 2N434 N438N433N437S390_078Effects of Signal Failure If a solenoid valve fails, that half of the transmission will be disabled.60Transmission Management SystemV401 Hydraulic Pump MotorThe motor for the hydraulic pump is integrated into the mechatronic unit hydraulic module. It is actuated by the transmission control unit. The control unit shuts off the motor when the hydraulic pressure in the system has reached 60 bar, and turns it on again when the pressure drops to 40 bar.V401S390_079Effects of Signal Failure If the motor cannot be actuated, the hydraulic pressure drops and the clutches open independently due to the spring force of the pressure plates.61Transmission Management SystemFunctional DiagramE313 Selector Lever E438 Tiptronic Upshift Button on Steering Wheel E439 Tiptronic Downshift Button on Steering Wheel F319 Selector Lever Park Position Lock Switch G182 Transmission Input Speed Sensor G270 Hydraulic Pressure Sensor G487 Gear Position Distance Sensor 1 G488 Gear Position Distance Sensor 2 G489 Gear Position Distance Sensor 3 G490 Gear Position Distance Sensor 4 G510 Temperature Sensor in Control Module G612 Transmission Input Speed Sensor 2 G617 Clutch Pedal Position Sensor 1 G618 Clutch Pedal Position Sensor 2 G632 Transmission Input Speed Sensor 1 J119 Multifunction Indicator J285 Instrument Cluster Control Module J453 Multifunction Steering Wheel Control Module J519 Vehicle Electrical System Control Module J527 Steering Column Electronics Control Module J533 Data Bus on Board Diagnostic Interface J681 Terminal 15 Power Supply Relay 2 J743 DSG Transmission Mechatronic N110 Shift Lock Solenoid N433 Sub-Transmission 1 valve 1 N434 Sub-Transmission 1 valve 2 N435 Sub-Transmission 1 valve 3 N436 Sub-Transmission 1 valve 4 N437 Sub-Transmission 2 valve 1 N438 Sub-Transmission 2 valve 2 N439 Sub-Transmission 2 valve 3 N440 Sub-Transmission 2 valve 4 V401 Hydraulic Pump Motor Y6 Selector Lever Position DisplayDiagnosis Connector62Transmission Management SystemInput Signal Output Signal Bi-directionalPositive Ground CAN Data BusS390_05463Transmission Management SystemCAN Data-bus ConnectionThe schematic shown below symbolically shows the integration of the mechatronic unit for direct shift transmission into the vehicle CAN data bus structure. J104 ABS Control Module J248 Diesel Direct Fuel Injection Engine Control module J285 Instrument Cluster Control ModuleJ J519 Vehicle Electrical System Control Module J527 Steering Column Electronics Control Module J533 Data Bus on Board Diagnostic Interface J587 Selector Lever Sensor System Control Module J623 Engine Control Module J743 DSG Transmission MechatronicDiagnostic connector"Powertrain" CAN data bus CAN "convenience" data busS390_05564ServiceSpecial ToolsWhen removing the transmission, a new special tool is available for aligning transmission support 3282 of engine and transmission jack V.A.G 1383 A. Adjustment plate 3282/59S390_09565Page intentionally left blankKnowledge AssessmentAn on-line Knowledge Assessment (exam) is available for this Self-Study Program. The Knowledge Assessment may or may not be required for Certification. You can find this Knowledge Assessment at: www.vwwebsource.comFor Assistance, please call: Volkswagen Academy Certification Program Headquarters 1-877-791-4838 (8:00 a.m. to 8:00 p.m. EST)Or, E-mail: concierge@volkswagenacademy.com67Volkswagen Group of America 2200 Ferdinand Porsche Drive Herndon, VA 20171 August 2012