TECHNICAL DOCUMENTATION

SSP 850193 – The 8-speed Automatic Transmission 09P

PDFEN37 pages2 MB
SSP 850193 – The 8-speed Automatic Transmission 09P - PDF cover

This PDF is currently unavailable.

Read document text
Self Study Program 850193The 8-speed Automatic Transmission 09PDesign and Function - Tablet Format Volkswagen Group of America, LLC Volkswagen Academy Printed in U.S.A. Printed 4/2019 VW Course Number: 850193 NHTSA ID: VWSSP 850193©2019 Volkswagen Group of America, LLC. All rights reserved. All information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Volkswagen Group of America, LLC. Always check Technical Bulletins and the latest electronic repair information for information that may supersede any information included in this booklet. Trademarks: All brand names and product names used in this manual are trade names, service marks, trademarks, or registered trademarks; and are the property of their respective owners. Table of ContentsIntroduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Selector Lever. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Transmission Design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Valve Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Oil Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Transmission Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 IntroductionThe Features of the 8-speed Automatic Transmission 09PThe new 8-speed automatic transmission 09P from Aisin has the following technical features when compared to the 09G/09M: • Transmission Fluid Auxiliary Hydraulic Pump 1 V475 for providing the oil supply in start/stop operation • Torque converter with starter ring gear • Two additional electric pressure control valves for gears 7 and 8 • An additional clutch on the Lepelletier planetary gearset for gears 7 and 8 • One of the two brakes is a band brakeThere are variances in the 09P transmission configurations depending on vehicle models.s585_0162 IntroductionThe Technical Data for the 8-speed Automatic TransmissionManufacturer Transmission code Transmission features Maximum torque ATF specification for transmission fluid Filling quantity gear oil Filling quantity bevel box AISIN AW CO., LTD. Japan AQ 450 8-speed automatic transmission with single Lepelletier planetary gear set 450 Nm (332 lb/ft) G 055 540 A2 - always check service information for the correct fluid 7.65 liters (8.0 qt) at a change interval of 200,000 km (125,000 miles) - always check maintenance information for the correct volume and replacement interval 0.86 (0.9 qt) liters lifetime fillingThe 09P ApplicationsThe 09P automatic transmission has multiple configurations, depending on application. It is available as a front-wheel drive or a four-wheel drive configuration.3 Selector LeverThe selector lever pictured is for the Crafter van (not for the North American Region). The basic layout of the selector lever module varies per application.Design of the Selector Lever ModuleThe selector lever module is made of the following main components: • The selector mechanism • The selector lever with bellows • The Transmission Range Display Y6 • The Selector Lever Park Position Lock Switch F319 • The Shift Lock Solenoid N110 • The Tiptronic Switch F189 • Shift Lever Gate Recognition Switch F257 • Mechanical, manual emergency release Selector LeverPlug connection C for Y6F189Electronics of the Selector Mechanism Connector A to the Vehicle Wiring Harness for the Transmissions585_042Selector MechanismEmergency ReleaseSelector Housing Selector Lever Cable4 Selector LeverHow the Selector Lever Module WorksThe selector lever operates the selector slide in the valve body and the multifunction switch via the selector lever cable and a relay lever. The selector lever module has both mechanical and electrical functions. Mechanical functions • Actuation of the parking lock • Actuation of the selector slide of the hydraulic control module • Actuation of the multifunction switch in the transmission Electrical functions • Ignition key lock • Control of the display unit for selector lever position • Tiptronic function • Selector lever lock (P/N lock) Selector Lever Park Position Lock Switch F319 The switch is operated by the selector lever in the “P” position. It then sends a signal “selector lever in position P” to the control module for steering column electronics. The module needs this signal to control the ignition key lock. Shift Lever Gate Recognition Switch F257 The switch recognizes the position of the selector lever and driver demand. The signal is compared with the multifunction switch and checked for plausibility. Tiptronic Switch F189 The switch detects the Tiptronic gate as well as “Tip +” and “Tip -.” An analog signal is sent to the TCM. Shaft to Selector Slides585_014Selector Lever CableMultifunction SwitchRelay LeverAdditional Electrical Elements of the Switching OperationMultifunction Switch The multifunction switch is connected to the selector mechanism with a cable. In the multifunction switch, the mechanical movement of the cable is converted into electrical signals by the selector lever position and transmitted to the Transmission Control Module (TCM).5 Selector LeverSelector Lever LockThe selector lever lock is engaged when the ignition is switched on and in the P and N positions during vehicle operation. When the ignition key is removed, the lock is engaged in the P position. The locking mechanism enables the selector lever to be locked both when the Shift Lock Solenoid N110 is de-energized (position P) and when the solenoid is energized (position N).Lock in selector lever position P If N110 is de-energized, the locking lever automatically engages in the P latch in the selector mechanism as soon as the selector lever is brought into position P. This movement of the locking lever is supported by an internal spring. For unlocking, N110 is energized, which means the solenoid pulls the locking lever out of the P latch.Lock in selector lever position N N110 is activated if the selector lever is in Neutral. The solenoid then pushes the locking lever with its upper hook into the N latch and the selector lever locks. N110 is switched off to release. The weight of the locking lever causes it to drop down and release the selector lever again.s585_025s585_0266 Selector LeverThe Mechanical, Manual Emergency Release of the P Latch The locking lever for the emergency release is located to the right of the selector mechanism. To unlock the selector lever lock, pull the locking lever backwards and press the selector lever lock button at the same time.Locking LeverSelector Mechanism Locking Pins585_035The Ignition Key Lock The ignition key lock prevents the ignition key from being turned back to the removal position if the parking lock is not engaged. It functions electromechanically and is controlled by the Steering Column Electronics Control Module J527. If the switch is open, the selector lever is in “P”, the Ignition Switch Key Lock Solenoid N376 is not energized. The ignition key can be removed.s585_0557 Transmission DesignThe Transmission at a GlanceThe transmission is divided into the following main assemblies: • The torque converter with torque converter lock-up clutch –– for front-wheel drive without centrifugal pendulum –– for four-wheel drive with centrifugal pendulum • The ATF oil pump • The planetary gear sets • The valve body • The transfer case (only for four-wheel drive) • The Transmission Control Module (in the engine compartment) Intermediate Shaft Planetary Gear Sets Differential Transmission HousingTorque Converter ATF PumpValve Bodys585_0028SumpOil Filter Transmission DesignTorque ConverterThe torque converter is a fluid coupling. Its primary purpose is to provide a fluid connection between the engine and the transmission. In addition, it magnifies torque. The torque converter has a turbine wheel, pump wheel and stator and a torque converter lock-up clutch. The torque converter of the four-wheel drive versions have centrifugal pendulums to compensate for torsional engine vibrations more efficiently. During operation, the pendulum inertia causes them to oscillate in the opposite direction to the engine oscillations, largely compensating for them. The torque converter is connected to different engines using a plate with six studs, which are permanently connected to the torque converter. Torque Converter Lock-up Clutch Turbine Stud Centrifugal Pendulum Absorbers Pump Impeller StatorTorsional Dampers585_018s585_0139 Transmission DesignThe Planetary Gear SetLike its predecessors, this automatic transmission also has two planetary gear sets arranged one behind the other. The first planetary gear set is a single planetary gear set. The second planetary gear set is a double planetary gear (Ravigneaux design). This special arrangement of the single + Ravigneaux gear sets together is called a Lepelletier planetary gear set. The first planetary gear set makes it possible to drive the second planetary gear set at two different speeds. Due to this special design, nine gears are possible. This means that transmissions with this design have an extremely wide range of applications between 5-speeds and 8-speeds. They differ only in the number of clutches and brakes required to implement the respective number of gears.s585_044Single Planetary Gear Set Lepellitier Planetary Gear SetDouble Planetary Gear Set (Ravigneaux)10 Transmission DesignThe Single Planetary Gear SetEngine torque passes from the torque converter to the transmission input shaft. From there it passes to the planetary gear carrier PT1. The sun gear S1 is permanently connected to the ATF oil pump. This means it cannot rotate freely. The planetary gear set PT1 has five planetary gears for transmission to the annulus H1. The single planetary gear set is integrated into the transmission using the clutches K1, K3 and K4 as well as the brake B1. Brake B1 Planetary Gear Carrier PT1 Annulus H1Input Shafts585_045Sun Gear S1Clutch K4 Clutch K3 Clutch K1s585_02211 Transmission DesignThe Double Planetary Gear Set (Ravigneaux)The clutches K1, K3 and K4 on the single planetary gear set and the clutch K2 on the Ravigneaux planetary gear set transmit the engine torque to this double planetary gear set. This happens either: • From the transmission input shaft via the single planetary gear set described above to the sun gears S2 or S3 • Or via the clutch K2 directly from the transmission input shaft to the planetary gear carrier PT2. Output to Differential Annulus H2 Planetary Gear Carrier PT2Brake B2Connection K3 and K4 with Sun Gear S2Input Shaft Connection K1 with Sun Gear S3s585_047The two sun gears S2 and S3 can rotate at different speeds. On the planetary gear carrier there are three planetary gears of different lengths P2a and P3a. The short planetary gears P2a engage in the sun gear S2 and the annulus H2 and the long planetary gears P3a engage in the annulus H2 and via inner planetary gears P3b on the sun gear S3. The double planetary gear set is integrated using the K2 clutch, the B2 brake and the freewheel. Sun Gear S2 Sun Gear S3Intermediate Shaft (Turbine Shaft) Clutch K2s585_02312 Transmission DesignThe BrakesBrake B1 Brake B1 is a band brake. It is connected to the transmission housing and is operated hydraulically using a control piston in the valve body. Brake B1 is controlled using the Automatic Transmission Pressure Regulating Valve 2 N216. The return movement is performed using a spring.Brake B1s585_027Brake B2 PT1 H1 S2B1S3s585_029Brake B2s585_030Brake B2 is designed as a multi-disc brake that is connected to the transmission housing. When the Solenoid Valve 1 N88 is energized, the hydraulic oil pressure compresses the brake disks. The planetary gear carrier PT2 is held.s585_028PT2 B213 Transmission DesignThe ClutchesThe clutches K1, K2, K3 and K4 The electric solenoid valves inside the valve body route fluid to open or close the clutches. The clutches perform the following functions when closed: • Clutch K1 connects the annulus H1 with the sun gear S3. • Clutch K2 connects turbine shaft to the planetary gear carrier PT2. • Clutch K3 connects the annulus H1 with the sun gear S2. • Clutch K4 connects the planetary gear carrier PT1 to the sun gear S2.s585_031Clutch K2 Clutch K4 Clutch K3 Clutch K114s585_049 s585_048 s585_034 s585_033 Transmission DesignParking LockIn order to protect the parking lock against unnecessary mechanical wear, a new design is used to prevent misuse of the parking lock. The parking lock serves exclusively to secure the vehicle against rolling away and is only allowed to be engaged when the vehicle is stationary. However, if the driver attempts to engage the parking lock when the vehicle is rolling in order to bring the vehicle to a standstill, a warning will appear in the instrument cluster. There are two warning levels.s585_050Warning Level 1 An acoustic warning tone of priority level 2 sounds. The display of the dash panel insert shows a warning message for six seconds.Only engage P when stationary! Wear of the parking lock!s585_052Warning Level 2 An acoustic warning tone of priority level 1 sounds. The display of the dash panel insert shows the adjacent warning message for six seconds. In addition, the central warning lamp lights up red. The display of this warning level repeats itself with each engine start. Warning level 2 cannot be reset. The transmission must be replaced.Parking lock damaged by misuse. Use handbrake. Workshop!s585_05315 Valve BodyThe Valve Body at a GlanceThe valve body is attached to bottom of the transmission. The clutches and brakes of the transmission are actuated by means of hydraulic valves, called shift valves, inside the valve body. The shift valves are controlled by electrically operated solenoid valves, which in turn are controlled by the Transmission Control Module J217. In addition to the shift valves, the valve body controls the various pressures in the transmission, such as main pressures, control pressures, torque converter clutch pressure and lubricating pressure. To provide the required oil pressure during start-stop operation, Transmission Fluid Auxiliary Hydraulic Pump 1 V475 is installed in the valve body. The valve body contains the following components: • The mechanically operated selector slide valve • Two electrically controlled solenoid valves (3/2-way valves) • Six electric pressure regulating valves with increasing characteristic curve (pressure increases with increasing control current) • One electric pressure regulating valve with decreasing characteristic (pressure decreases with increasing control current) • The Transmission Fluid Temperature Sensor G93 • The electric Transmission Fluid Auxiliary Hydraulic Pump 1 V47516 Valve BodyAutomatic Transmission Pressure Regulating Valve 1 N215 (falling characteristic) Solenoid Valve 2 N89 (solenoid valve) Transmission Fluid Temperature Sensor G93 Solenoid Valve 1 N88 (solenoid valve) Selector Slide Transmission Fluid Auxiliary Hydraulic Pump 1 V475 Automatic Transmission Pressure Regulating Valve 8 N510 (rising characteristic)Automatic Transmission Pressure Regulating Valve 6 N371 (rising characteristic)s585_019Automatic Transmission Pressure Regulating Valve 3 N217 (rising characteristic)Automatic Transmission Pressure Regulating Valve 4 N218 (rising characteristic)Automatic Transmission Pressure Regulating Valve 2 N216 (rising characteristic)Automatic Transmission Pressure Regulating Valve 5 N233 (rising characteristic)17 Valve BodySolenoid ApplicationGears Solenoid Valves Solenoid Valve 1 N88 Solenoid Valve 2 N89 Automatic Transmission Pressure Regulating Valve 1 N215 Automatic Transmission Pressure Regulating Valve 2 N216 Automatic Transmission Pressure Regulating Valve 3 N217 Automatic Transmission Pressure Regulating Valve 4 N218 Automatic Transmission Pressure Regulating Valve 5 N233 Automatic Transmission Pressure Regulating Valve 6 N371 Automatic Transmission Pressure Regulating Valve 8 N510 X X X P R N 1 2 3 4 5 6 7 8The pressure regulating valve 1 modulates the main oil pressure of the transmissiondepending on of the accelerator pedal value. X X X X X X X X X X X X X X X X -The pressure regulating valve 8 modulates the oil pressure for the torque converter lock-up clutch depending on the shift strategy.- = Valve switched off, clutch open, brake not applied X = Valve switch on, clutch closed, brake applied X* = Only closed in Tiptronic mode in 1st in certain driving situations to use the engine braking effect18 Valve BodyClutch/Brake ApplicationGears Clutches Clutch K1 Clutch K2 Clutch K3 Clutch K4 Brakes/freewheel Brake B1 Brake B2 Gliding -PRN12345678X ---X -X X -X -X XX X -X X XX -X--X --X* XX ------X ------ = Valve switched off, clutch open, brake not applied X = Valve switch on, clutch closed, brake applied X* = Only closed in Tiptronic mode in 1st in certain driving situations to use the engine braking effect19 Oil SupplyThe ATF Oil PumpFor vehicles with internal combustion engines, the mechanical ATF (Automatic Transmission Fluid) pump is responsible for the supply of hydraulic oil to the transmission during normal driving. It draws the ATF oil from the oil sump, builds up the oil pressure and supplies the valve body with the hydraulic fluid required for the gear changes.s585_054The ATF oil pump is an internal geared wheel pump (duocentric oil pump). It is driven directly by the engine through the converter housing by the converter hub. Here, the drive lugs of the pinion of the ATF oil pump engage in two grooves on the converter hub.s585_01220 Oil SupplyTransmission Fluid Auxiliary Hydraulic Pump 1 V475The electric oil pump is required for vehicles with start-stop system. It maintains the oil pressure in the transmission when the engine is stopped. The transmission can use pressure to apply clutches, allowing the vehicle to move immediately. After the engine has started again and the mechanical oil pump has built up the required oil pressure, the Transmission Fluid Auxiliary Hydraulic Pump 1 V475 is turned off.s585_020s585_02121 Transmission ManagementSensorsSystem OverviewActuators Shift Lock Solenoid N110 Selector Lever Park Position Solenoid N380Back-Up Switch F41 Transmission Park Selector Switch F305 Selector Lever Park Position Lock Switch F319 Multifunction Transmission Range Switchh F125 Tiptronic Switch F189 Selector Lever Sensor System Control Module J587 Vehicle Electrical System Control Module J519Engine/Motor Control Module J623Transmission Range Display Y6Steering Column Electronics Control Module J527Transmission Fluid Temperature Sensor G93Data Bus on Board Diagnostic Interface J533 Transmission Control Module J217Solenoid valve 1 and 2 N88, N89Transmission Input Speed Sensor 1 G632 Transmission Output Speed Sensor G195Instrument Cluster Control Module J285Automatic Transmission Pressure Regulating Valve1 - 6 &8 N215, N216, N217, N218, N233, N371, N510 Transmission Fluid Auxiliary Hydraulic Pump 1 V47522 Transmission ManagementThe Transmission Control Module J217The J217 is located in the front left of the engine compartment. It is connected to J533 Diagnostic Interface for the CAN Data-Bus through the powertrain CAN-bus. The J217 directly controls the solenoid valves in the valve body using signals from the transmission sensors. A 52-pin plug connects the control module to the on-board electrical system and the transmission. The VAS adapter cable 1598/48 is available for static and dynamic measurements on the system. The manufacturer of the control module is also AISIN AW Japan. Update programming is possible using the VAS Scan Tool. The Dynamic Shift Program DSP is integrated in the control module. This shift program evaluates the driving resistance (such as driving on hilly terrain), the route profile (such as windy roads) and the driving style, along with other factors, to determine the transmission shift points.s585_03723 Transmission ManagementPowerflowThe powerflow of the individual gears are shown in the following pages using a highly simplified cross-section of the transmission. The illustration of the valve body shows which solenoid valves are activated for the respective gear. PT 1 Clutch K1 and Freewheel F The transmission input shaft transmits the engine torque to the planetary gear carrier PT1 of the single planetary gear set. The planetary gears P1 roll around supported on the fixed sun gear S1 and drive the annulus H1. Clutch K1 connects the planetary gear carrier H1 to the sun gear S3, transferring the torque to the double planetary gear set. The freewheel locks the planetary gear carrier PT2. From the sun gear S3, the torque is transferred to the planetary gears P3. Supported by the planetary gear carrier PT2, the torque is transferred to the annulus H2. N217 Annulus H2 is connected to the transmission output shaft. In certain driving situations, engine braking can be used by selecting 1st gear in Tiptronic mode. Using engine braking in 1st gear is made possible by closing the brake B2. Brake B2 locks the planetary gear carrier PT2 to the freewheel. Unlike the freewheel F, however, the brake B2 holds the planetary gear carrier PT2 in both directions of rotation. N88 1st GearH1 H2 K1 P2 P3 S3 B2 PT2s585_00324 Transmission ManagementClutch K1 and Brake B1 As with the first gear, the engine torque is introduced into the double planetary gear set by the annulus H1 of the single planetary gear set. Clutch K1 connects the annulus H1 to the sun gear S3 for this purpose. Brake B1 locks the sun gear S2. From the sun gear S3, the torque is transferred to the planetary gears P3. Planetary gears P2 roll around the sun gear S2 and, together with the planetary gears P3, drive annulus H2. 2nd GearB1H1 H2 PT 1 K1 P2 P3 S3 B2 PT2N88s585_004N217 N21625 Transmission ManagementClutches K1 and K3 As before, the clutch K1 connects the annulus H1 to the sun gear S3. Clutch K3 additionally connects the annulus H2 to the large sun gear S2. Planetary gears P2 and P3 are locked by K1 and K3. Planetary gear carrier PT2 now rotates together with the sun gears S2 and S3. The torque is transmitted through the planetary gear carrier PT2 to the annulus H2. K3 H1 H2 PT 1 K1 P2 P3 B2 PT2 3rd GearS2 S3N89s585_005N217 N23326 Transmission ManagementClutches K1 and K4 Once again, the clutch K3 connects the annulus H1 to the sun gear S3 and transfers the torque to the double planetary gear set. Clutch K4 connects the planetary gear carrier PT1 to the sun gear S2 and also transfers the torque to the double planetary gear set, although with different input speeds. Sun gear S3 is driven more slowly than the sun gear S2. Planetary gears P2/P3 roll around the faster-rotating sun gear S2 and drive the annulus H2. K4 H1 H2 PT 1 K1 P2 P3 B2 PT2 4th GearS2 S3N89s585_006N217N37127 Transmission ManagementClutches K1 and K2 Clutch K1 connects the annulus H1 to the sun gear S3 and transfers the torque to the double planetary gear set. The clutch K2 connects the turbine shaft to the planetary gear carrier PT2 and transfers the torque to the double planetary gear set. Together with the planetary gear carrier PT2, planetary gears P2 and P3 drive the annulus H2. PT 1 K1 5th GearH2 P2 P3K2 PT2S2 S3s585_007N217 N218N21828 Transmission ManagementClutches K2 and K4 The turbine shaft drives the planetary gear carrier PT1 of the single planetary gear set and the outer disc carrier of the clutch K2. The clutch K4 connects the planetary gear carrier PT1 to the sun gear S2, transferring the torque to the double planetary gear set. The clutch K2 connects the turbine shaft to the planetary gear carrier PT2 and transfers the torque to the double planetary gear set. Sun gear S2 transfers the torque to the planetary gears P2. The torque is transferred to the planetary gears P3 through the planetary gear carrier PT2. Together with the planetary gears P2, the planetary gears P3 drive the annulus H2. 6th GearK4H1 H2 K2 P3 PT2PT 1P2S2 S3s585_008N218N37129 Transmission ManagementClutches K2 and K3 The turbine shaft drives the planetary gear carrier PT1 of the single planetary gear set and the outer disc carrier of the clutch K2. Planetary gear carrier PT1 drives the planetary gears P1, which roll around the fixed sun gear S1 and drive the annulus H1. Clutch K3 connects the annulus H1 to the sun gear S2, transferring the torque to the double planetary gear set. The clutch K2 connects the turbine shaft to the planetary gear carrier PT2, transferring the torque to the double planetary gear set. The planetary gears P2, which are jointly driven by sun gear S2 and planetary gear carrier PT2, drive the annulus H2 along with the permanently connected outer planetary gears P3. 7th GearK3H1 H2 K2 P3 PT2PT 1P2 S2s585_009N218 N23330 Transmission ManagementClutches K2 and Brake B1 Brake B1 locks the sun gear S2. Clutch K2 connects the turbine shaft to the planetary gear carrier PT2 of the double planetary gear set, transferring the torque to the double planetary gear set. The long planetary gears P3 roll around the stationary sun gear S2 and, together with the planetary gears P2, drive the annulus H2. The clutches K1 and K3 are open. The single planetary gear set is not part of the power flow. 8th GearB1H1 H2 PT 1 P2 S2 P3 K2 PT2s585_010N218 N21631 Transmission ManagementClutches K3 and Brake B2 The turbine shaft drives the planetary gear carrier PT1 of the single planetary gear set. The planetary gear carrier PT1 drives the planetary gears P1, which roll around the fixed sun gear S1. The annulus H1 is driven. Clutch K3 connects the annulus H1 to the sun gear S2, transferring the torque to the double planetary gear set. In the double planetary gear set, brake B2 locks the planetary gear carrier PT2. From the sun gear S2, the torque is transferred to the planetary gears P2 and P3. Supported by the planetary gear carrier PT2, the torque is transferred to the annulus H2, which is connected to the output shaft. Annulus H2 is driven against the direction of engine rotation. Reverse GearK3H1 H2B2PT 1P2 S2P3PT2N510585_01 1N23332 ServiceSpecial ToolsDesignation T10173 Setting gauge Tool Use To set the multifunction switchs585_04033 Knowledge AssessmentAn on-line Knowledge Assessment (exam) is available for this Self-Study Program. The Knowledge Assessment may or may not be required for Certification. You can find this Knowledge Assessment at: www.vwwebsource.com For Assistance, please call: Volkswagen Academy, Certification Program Headquarters 1-877-791-4838 (8:00 a.m. to 8:00 p.m. EST) Or, E-mail: concierge@volkswagenacademy.com34 Volkswagen Group of America 2200 Ferdinand Porsche Drive Herndon, VA 20171 2019