TECHNICAL DOCUMENTATION
SSP 920213 – The Second Generation 3,0L V6 TDI Engine

This PDF is currently unavailable.
Read document text
Self-Study Program 920213The Second Generation 3.0L V6 TDI EngineAudi of America, LLC Service Training Printed in U.S.A. Printed 9/2012 Course Number 920213©2012 Audi of America, LLCAll rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher.All requests for permission to copy and redistribute information should be referred to Audi of America, LLC.Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Technical Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Engine Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Cylinder Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Crankshaft Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Chain Drive System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Cylinder Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Oil Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Oil Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Engine Oil Pump with Integral Vacuum Pump . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Engine Oil Cooler with Thermostat Controlled Bypass Port. . . . . . . . . . . . . . 11Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Coolant Circuit and Thermal Management System . . . . . . . . . . . . . . . . . . . . . 13 Cylinder Head Cooling Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Cylinder Block Cooling Circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Exhaust Gas Recirculation . . . . . . . . . . . . . . . . . . . . . . . . . .16Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Active EGR Cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Intake Air Ducting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Turbocharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19Charge Air Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Common Rail Injection System . . . . . . . . . . . . . . . . . . . . .21Chain-Driven Injection System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Fuel Delivery System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Engine Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Special Tools and Workshop Equipment . . . . . . . . . . . . .26 Knowledge Assessment . . . . . . . . . . . . . . . . . . . . . . . . . . .29iThe Self-Study Program provides introductory information regarding the design and function of new models, automotive components, or technologies. The Self-Study Program is not a Repair Manual! All values given are intended as a guideline only. For maintenance and repair work, always refer to current technical literature.ReferenceNote!iiIntroductionThe success story for V6 TDI engines at Audi began in 1997 with the introduction of the world’s first four-valve 2.5 liter V6 TDI with a distributor injection pump fuel system. In late 2003, this engine was followed by a 3.0 liter V6 TDI with common rail fuel injection. A power reduced 2.7 liter version was introduced in 2004 but was not offered in the U.S. market. V6 TDI engines have evolved with much success in various Audi and VW Group models. The second generation 3.0L V6 TDI engine features state-of-the-art diesel technology, such as a common rail fuel system with piezo fuel injectors, systematic thermal management, and extensive friction reducing improvements. This ensures that lower emissions and higher fuel economy are achieved.479_0011Technical FeaturesBosch CRS 3.3 common rail injection system479_008Intake manifold with a single swirl flap479_012Chain drive479_0032Turbocharger module479_005Exhaust gas recirculation479_002479_004Thermal management system479_010 3Specifications268.2 hp (200 kW)442.5 lb ft (600 Nm)234.6 hp (175 kW)405.6 lb ft (550 Nm)201.1 hp (150 kW) Power in hp (kW) Torque in lb ft (Nm) 167.6 hp (125 kW)368.7 lb ft (500 Nm)331.9 lb ft (450 Nm)134.1 hp (100 kW)295.0 lb ft (400 Nm)hp (kW)lb ft (Nm)67.05 hp (50 kW)221.2 lb ft (300 Nm)0100020003000400050006000 479_019Engine Code (model dependent) Engine type Displacement Stroke Bore Cylinder spacing Number of valves per cylinder Firing order Compression ratio Power output Torque Fuel Engine management Emissions standardQ7: CNRB, Q5: CPHA, A8: CPNA Six-cylinder 90° V-engine 181.0 cu in (2967 cm3) 3.59 in (91.4 mm) 3.26 in (83 mm) 3.54 (90 mm) 4 1-4-3-6-2-5 16.8 : 1 246.7 hp (184 kW) @ 4000 rpm 405.6 lb ft (550 Nm) @ 1250–3000 rpm Diesel to EN 590 Bosch CRS 3.3 ULEV Tier II Bin54Engine DesignCylinder BlockThe cylinder block is made from vermicular graphite cast iron (CJV-450). This material provides high strength and load capacity. The proven bearing frame design principle from the previous generation V6 TDI engine has been adopted for the crankshaft bearings of this engine. The weight of the cylinder block has been reduced by 17.6 lb (8.0 kg) when compared to the first generation V6 TDI engine. This was accomplished partly through systematic reductions in wall thickness.Cylinder blockBalance shaftDividing plane at center of crankshaft CrankshaftOil pan upper section479_013Bearing frameTo ensure a perfectly round cylinder shape, the cylinder block is plate honed during the final machining processes. A special plate is mounted on the cylinder block to simulate the effect of an installed cylinder head. A round bore ensures a substantial reduction in piston ring pre-stress which results in lower blow-by gases and less mechanical friction.At the final stage of cylinder bore machining, the UV photon exposure process is applied. This ensures that a smooth cylinder bore surface is obtained without necessitating mechanical work (wear-in) by the piston.5Crankshaft AssemblyThe forged 42 CrMo54 crankshaft has a split pin design to achieve identical firing intervals. Due to the strong shear forces to which the crankshaft is subjected, both the main bearing journals and connecting rod journals are induction hardened. Weight to the crankshaft assembly has been reduced by eliminating the center counterweights and machining relief bores in the main journals. The forged connecting rods are diagonally split and cracked at the big end. Approximately 2683.1 psi (185 bar) are generated during the combustion process. For optimal cooling of the piston ring assembly and recess rim, the aluminum pistons have an annular salt core cooling gallery and are sprayed from below by oil jets mounted on the cylinder block.Annular oil cooling galleryTrapezoidal connecting rodSplit pin connecting rod bearing journalOil supply port of the connecting rod bearingsTransverse bore in the crankshaftConnecting rod bearingConnecting rod cap479_016_0186Chain Drive SystemThe second generation V6 TDI engine has a new chain drive layout compared to the first generation V6 TDI. The new chain layout reduces the number of chains and chain tensioners from four to two and eliminates the need for idler sprockets. A relatively long roller chain (206 links) is used to drive the intake camshafts and balance shaft. To counteract chain elongation, the chain pins have a wear-resistant coating. The auxiliary drive chain is also a roller-type. It drives the high-pressure fuel injection pump in the rear inner Vee of the engine, and the combined oil pump/vacuum pump.High-pressure pump CP4.2Balance shaft Timing gear for camshafts and balance shafts Timing drive chain tensionerAuxiliary drive chain tensionerVacuum pumpCrankshaft479_003 Two-stage variable oil pump Auxiliary drive7Cylinder HeadThe proven first generation V6 TDI four-valve cylinder head design has been adapted for the second generation engine. This new engine features swirl ports and charging ports in the intake, both of which have been redesigned to enhance swirl and throughflow, while the exhaust side has two exhaust ports merging into a Y-branch pipe. The cylinder head cooling concept has been revised to reduce component temperatures around the combustion chamber despite increased engine power output. The exhaust valves have been reduced in size and moved further apart. This reduces the area needed to be cooled. The cylinder head is designed for directional coolant flow with high flow rates. This ensures that optimal cooling is provided between the valves and the fuel injector bore, which are in close proximity to the combustion chamber.Action springThe Hydro-formed hollow camshafts are mounted on the cylinder heads on split twin bearing pedestals rather than a ladder frame. The camshafts have been repositioned inward (or closer to each other) allowing them to be designed without additional clearances to access the head bolts. To minimize friction in the valve train, the diameter of the camshaft bearings has been reduced to 0.9 in (24.0 mm) from 1.25 in (32.0 mm). The crankcase ventilation system (both coarse and fine oil separators) has been moved from the Vee of the engine into the cylinder head covers. Both crankcase vents lead to the pressure control valve and from there to the intake side of the turbocharger.Swirls Sealing cover with swirl port Constant-pressure valveOil return lineFine oil separator Oil separator moduleBlow-by gas inletComposite hollow camshaftsCamshaft bearing pedestals Pretensioned gears to drive the exhaust camshafts Glow plug Roller cam followers 8 479_015Oil CircuitOil Circuit Schematic479_028Legend: A B C D E F G H Camshaft bearing Balancer elements Chain tensioner Exhaust turbocharger Crankcase ventilation fine oil separator Non-return valve Flow restrictor Piston cooling jets with integrated valves I J K L M N O Main bearing Thermostat Water-oil heat exchanger Oil Temperature Sensor G8 Filter bypass valve Oil filter Reduced Oil Pressure Switch F378 P Q R S T U V W Oil Pressure Switch F22 Oil Pressure Regulation Valve N428 Vacuum pump Oil pump Relief valve Oil pump drive gear bearing Intake sieve Oil Level Thermal Sensor G2669Engine Oil Pump with Integral Vacuum PumpEngine oil is circulated by a flow rate controlled vane cell pump. A rotating adjustment ring regulates the volumetric engine oil flow which results in reducing the amount of drive power required to operate the pump. The amount of oil flow required is mainly based on engine load. Depending on engine load, oil temperature, and other operating parameters, a lower oil pressure is used at engine speeds less than 2500 rpm. The vacuum pump uses a rotor to generate necessary vacuum.Ball valveVacuum pump coverOil pump housingVacuum pump housingRelief valveAdjustment ringRotor with vacuum pump vane Drive shaftVane cellsControl springs 479_020 Oil pump coverOil pick-upReference For more detailed information about the flow rate controlled oil pump, refer to Self-Study Program 941803, Audi 3.0-liter V6 TDI With Clean Diesel System.10Engine Oil Cooler with Thermostat Controlled Bypass PortTo assist thermal management of the engine, a thermostatically controlled oil bypass is integrated in the engine oil cooler. At temperatures below 217.4°F (103°C), the bypass port is open and the main volume of oil bypasses the engine oil cooler. At temperatures above 217.4°F (103°C), the wax expansion element moves a lifting pin and the oil thermostat opens. The main volume of oil is then directed through the engine oil cooler. Installation Location The thermostat is located in the cylinder block beneath the coolant pump.Coolant pump drive gear mountingThermostat Coolant pump housing479_030Guide bushing Lifting pinCompression springExpanding wax thermostat 479_031 Cylinder block11Cooling SystemOverviewExample: 2013 Audi A8ABHot coolant Cooled coolantC D EFGIJK H LOMNPQ479_021Legend: A B C D E F G H I12Front heater heat exchanger Rear heater heat exchanger Coolant Recirculation Pump V50 ATF cooler Transmission Coolant Valve N488 Exhaust turbocharger Coolant expansion tank Alternator Engine Coolant Temperature Sensor G62J K L M N O P QEGR cooler Coolant shutoff valve Engine oil cooler Coolant thermostat Coolant pump Engine Temperature Control Sensor G694 Engine Coolant Temperature Sensor on Radiator G83 RadiatorCoolant Circuit and Thermal Management SystemTo increase efficiency, it is best to heat up the engine as quickly as possible. This is accomplished on the V6 TDI engine by using a split cooling system concept. Engine coolant flows through the cylinder block and cylinder heads in two separate but parallel cooling circuits. A continuous-duty coolant pump mounted in the Vee at the front of the engine delivers coolant to the cylinder block at the exhaust sides of the engine. The coolant flow then divides into two streams to the cylinder heads and the cylinder block, returning to the intake side of the pump after flowing through both sub-circuits.Heater inletConnection to air bleed valve from cylinder blockEGR coolerEngine Coolant Temperature Sensor G62Coolant shutoff valveMap Controlled Engine Cooling Thermostat F265Return line from radiatorCoolant pumpRadiator inlet479_009 Engine Temperature Control Sensor G694Cylinder head cooling circuit Cylinder block cooling circuit13Cylinder Head Cooling CircuitThe continuous-flow cylinder head cooling circuit primarily consists of: • Coolant chambers in both cylinder heads • Engine oil and EGR cooler • Passenger compartment heat exchanger and transmission heat exchanger • Coolant radiator Hot coolant is provided for heating the ATF oil and for passenger compartment heating as necessary. The temperature level of the cylinder head cooling circuit can be reduced, within the physical bounds of the radiator, by energizing the map-controlled engine cooling thermostat. The limiting conditions for this function are: • Maximum EGR cooling capacity is required • • Component protection of the cylinder head under high component load Transmission cooling is requiredThe temperature level of the cylinder head cooling circuit is controlled via a mapped thermostat with a heated wax expansion element. The thermostat is de-energized during the warm-up phase and opens at 194°F (90°C). This means that no thermal energy is dissipated to the main coolant radiator until the opening temperature is reached.Pneumatic control valve (controls the cylinder head and cylinder block cooling system)Engine oil coolerCylinder head cooling circuit Cylinder block cooling circuitCylinder block cooling circuit closed479_011!14Note The cooling system is equipped with a control valve and can only be filled using VAS 6096 (vacuum filling). Follow all instructions outlined in current technical literature.Cylinder Block Cooling CircuitCoolant is admitted to the cylinder head cooling circuit on the exhaust sides of the cylinder banks via a non-return valve. Non-return valves serve to prevent coolant back flow between the two cylinder banks, while eliminating unwanted heat dissipation from the cylinder block. The cylinder block cooling circuit is positioned above the coolant outlet, with the vacuumcontrolled ball valve shut OFF and operated with stationary coolant to shorten the warm-up phase of the engine.Return via cylinder head Engine oil coolerAfter the engine has heated up, the temperature level in the cylinder block cooling circuit is adjusted to approximately 221°F (105°C) via the ball valve. The ball valve is activated by a pulse width modulated (PWM) signal by Cylinder Head Coolant Valve N489. To promote rapid heating, an oil-side oil cooler bypass is utilized.Cylinder headCylinder block cooling circuit open479_010This cylinder block cooling circuit has a separate vent. The water jackets of the cylinder banks are connected to a header rail in the cylinder heads via the cylinder head gaskets. This ensures that air bubbles are able to leave the cylinder block circuit at the highest point in the system, even when the coolant is stationary. The ventilation lines lead from the header rails to a breather valve which interconnects the permanent ventilation system of the cylinder head circuit and the ventilation system of the cylinder block circuit. The breather valve seals both sub-circuits off from one another via a floating ball valve. Therefore, when the cylinder head circuit is ventilated, no heat energy can dissipate from the cooling circuit via the permanent ventilation system.Breather valveFrom cylinder head cooling circuit to expansion tankFrom cylinder head cooling circuit479_03315Exhaust Gas RecirculationOverviewThe exhaust gas recirculation system plays a key role in meeting applicable emission standards. All functional elements of the EGR system are integrated into an EGR module consisting of an EGR valve, EGR cooler, and a bypass valve. EGR Motor V338 is continuously adjustable and has been optimized to achieve greater adjustment capabilities.Pulsation damperTo reduce pressure loss in the EGR system, the seat diameter of the EGR valve has been increased to 1.18 in (30 mm) from 1.06 in (27 mm), compared to the first generation V6 TDI engine.Turbocharger Control Module 1 J724Integral insulationExhaust turbochargerEGR Motor V338 Exhaust gas recirculation pipeDecoupling elementEGR coolerEGR Temperature Sensor G98Air gap insulated exhaust manifold479_004 Intake manifold inlet16Active EGR CoolerThe tubular stainless steel EGR cooler has enhanced cooling capacity and is integrated in the module’s aluminum housing. A pneumatically actuated lift valve is used in lieu of a flap to bypass the EGR valve. The major advantage of the lift valve is that its seat guarantees a vacuum-tight seal during cooling operation and therefore ensures a higher cooling capacity.EGR Motor V338 Engine Coolant Temperature Sensor G62 Water return line to oil filter module thermostat housing EGR coolerEGR valve EGR Temperature Sensor G98EGR cooler bypass valveCylinder head coolant inlet479_00717Intake Air DuctingIntake air is inducted from the front of the vehicle and directed through the filter housing to the throttle valve. Just past the throttle valve, recirculated exhaust gas is admitted to the intake path through a thermally de-coupled stainless steel intake. The geometric design of the exhaust gas intake helps to avoid build-up on the inner wall of the plastic tube at all operating points, while ensuring a good degree of mixing. A single, central swirl flap is used on the second generation TDI engine instead of the six swirl flaps used on the first generation engine. After the central swirl flap, the intake manifold has a twin-flow configuration up to both cylinder banks. The upper half channels air into the swirl ports and the lower half into the charging ports. Intake manifold geometry was also enhanced to better control pressure loss and ensure uniform airflow distribution to the individual cylinders.Twin-Flow Intake ManifoldCentral swirl flapEGR inletThrottle Valve Control Module J338479_01218TurbochargingThe turbocharger for the V6 TDI engine is manufactured by Honeywell Turbo Technologies. The compressor and turbine wheel design has been optimized for flow and the bearing assemblies have been enhanced to reduce frictional losses. Optimized cylinder charging and a reduction in charge cycle losses has been accomplished through minimizing flow restrictions in the intake manifold, and redesigning the swirl and inlet ports.Turbocharger Control Module 1 J724 Integral insulation Wastegate actuating rodConnection to intake manifoldConnection to exhaust systemConnection to EGR system479_005Over-Boost Function When driving between speeds of 6.2–74.5 mph (10–120 km/h), with the accelerator pedal angle exceeding 70% under acceleration, the overboost function increases nominal engine output by approximately 13.4 hp (10 kW) for a period of 10 seconds. This function is deactivated: • • When towing a trailer When the charge air temperature exceeds 131°F (55°C)To avoid sudden changes in torque, the overboost function is activated and deactivated by a map-controlled program.19Charge Air CoolingThe complete air circulation system, from the air filter to the turbocharger, has been redesigned for minimum pressure loss. The pressure-side air circulation system, with only one charge air cooler, has also been optimized via low-swirl transitions between the hose connections. This has resulted in improved engine response, as well as lower emissions and greater fuel economy.Exhaust turbochargerAir filterThrottle Valve Control Module J338Air inletCharge Air Pressure Sensor G31 and Intake Air Temperature Sensor G42Charge air cooler 479_00620Common Rail Injection SystemChain-Driven Injection SystemThe second generation V6 TDI engine uses the latest Bosch common rail fuel injection system. Fuel pressure is produced by a CP4.2 dual plunger high-pressure pump housed in a single aluminum casting. The piezo injectors are connected to the short forged rails by stainless steel lines and are capable of withstanding pressures of over 29,000 psi (2000 bar). The high-pressure pump housing is located in the Vee on the transmission side of the cylinder block below the turbocharger. It is driven directly by the crankshaft via a secondary drive chain. It is critical that fuel delivery is synchronized with the injection phase. To help achieve this, a pump pulley to crankshaft ratio of 1:0.75 is used. The chain forces on the pump must be kept to a minimum. This is accomplished through the chain drive and pump mount design. These modifications minimize differences in the amount of fuel injected into each of the cylinders across the entire operating range. This is very important with regard to achieving lower emissions.Fuel Metering Valve N290 High pressure pump CP4.2Fuel Pressure Regulator Valve N276 Fuel Pressure Sensor G247Injectors for cylinders 1, 2, 3 N30, N31, N32Injectors for cylinders 4, 5, 6 N33, N83, N84479_008!Note Always observe all Cautions and Warnings in current technical literature when removing and installing the high pressure pump.21Fuel Delivery System3.0L V6 TDI Engine (Example: 2013 Audi A8)Fuel Metering Valve N290High Pressure Pump CP4.2Fuel Temperature Sensor G81Pressure retention valveFuel filter22Fuel Pressure Sensor G247High-pressure accumulator 2 (rail) Injectors for cylinders 4, 5, 6 (N33, N83, N84)High-pressure accumulator 1 (rail) Fine oil separator Fuel Pressure Regulator Valve N276Injectors for cylinders 1, 2, 3 (N30, N31, N32)Non-return valveNon-return valveEngine Control Module J623Battery (positive)Fuel Pump Control Module J538Transfer Fuel Pump G6Baffle housing479_02923Engine ManagementSystem OverviewSensorsMass Airflow Sensor G70Engine Speed Sensor G28Camshaft Position Sensor G40Engine Coolant Temperature Sensor G62Engine Coolant Temperature Sensor on Radiator G83Fuel Temperature Sensor G81Engine Temperature Control Sensor G694Oil Level Thermal Sensor G266Fuel Pressure Sensor G247Accelerator Pedal Position Sensor G79 Accelerator Pedal Position Sensor 2 G185 EGR Potentiometer G212Brake Light Switch FCharge Air Pressure Sensor G31 Intake Air Temperature Sensor G42 Heated Oxygen Sensor G39Oil Temperature Sensor 2 G664Oil Pressure Switch F22Reduced Oil Pressure Switch F378 Exhaust Gas Temperature Sensor 3 G495Engine Control Module J623EGR Temperature Sensor G98Exhaust Gas Temperature Sensor 1 G235Exhaust Gas Temperature Sensor 4 G648 (after particulate filter) Differential Pressure Sensor G505 Additional signals: • Cruise control system • Terminal 50 • Crash signal • Speed signal from Airbag • Start request to Control Module ECM (Kessy 1 + 2)Data Link Connector24Powertrain CAN data busActuatorsPiezoelectric Fuel Injectors for Cylinders 1–3 N30, N31, N32Piezoelectric Fuel Injectors for Cylinders 4–6 N33, N83, N84Glow plugs Q10, Q11, Q12 Automatic Glow Time Control Module J179Glow plugs Q13, Q14, Q15Oil Pressure Regulation Valve N428Throttle Valve Control Module J338Fuel Metering Valve N290Fuel Pressure Regulator Valve N276EGR Motor V338EGR Cooler Switch-Over Valve N345Cylinder Head Coolant Valve N489Turbocharger Control Module 1 J724Map Controlled Engine Cooling Thermostat F265Fuel Pump Control Module J538Left Electro-Hydraulic Engine Mount Solenoid Valve N144 Right Electro-Hydraulic Engine Mount Solenoid Valve N145Oxygen Sensor Heater Z19Fuel Pump Relay J17Transfer Fuel Pump G6 Additional signals: • A/C compressor • Auxiliary Heater • Auxiliary coolant heater Heating Element • Fan setting 1 + 2 Z35479_032 25Special Tools and Workshop EquipmentDetent T40246Installing tool T40048/7479_040Used to hold the chain guide when removing the camshaft timing chain.479_041Used for pressing in crankshaft seal.Retainer VAS 6395/6Counter-hold tool T40248479_043479_042Used to hold the high pressure pump shaft when replacing the high-pressure pump.Used when replacing Turbocharger Control Module 1 J724.26Guide plate VAS 5161-29Sealing pin VAS 5161-29-1479_047479_045For replacing valve keepers on the V6 TDI engine.Engine support VAS 6095-1-11Locking pin T40245479_044Used to lock the high-pressure pump sprocket in place when removing pump.479_046Used with engine/transmission stand VAS 6095.27Notes28Knowledge AssessmentAn on-line Knowledge Assessment (exam) is available for this Self-Study Program. The Knowledge Assessment is required for Certification. You can find this Knowledge Assessment at:www.accessaudi.comFrom the accessaudi.com Homepage: • Click on the “ACADEMY” tab • Click on the “Academy Site” link • Click on Course Catalog Search and select “920213B — The Audi 3.0L V6 TDI Engine (second generation)”Please submit any questions or inquiries via the Academy CRC Online Support Form which is located under the “Support” tab or the “Contact Us” tab of the Academy CRC.Thank you for reading this Self-Study Program and taking the assessment.29All rights reserved. Technical specifications subject to change without notice. Audi of America, LLC 2200 Ferdinand Porsche Drive Herndon, VA 20171920213