TECHNICAL DOCUMENTATION
SSP 920243 – The Audi 1,8L and 2,0L Third Generation EA888 Engines

This PDF is currently unavailable.
Read document text
eSelf-Study Program 920243The Audi 1.8L and 2.0L Third Generation EA888 Engines1Audi of America, LLC Service Training Created in the U.S.A. Created 11/2013 Course Number 920243 ©2013 Audi of America, LLC All rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC. Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.Revision 2: 12/20132ContentsIntroduction..........................................................................................5Development goals ....................................................................................................................................................... 6 Brief technical description ........................................................................................................................................... 7 Technical features ........................................................................................................................................................ 8Engine mechanicals............................................................................ 10Overview ......................................................................................................................................................................10 Cylinder block ..............................................................................................................................................................10 Oil pan ..........................................................................................................................................................................11 Crankshaft assembly ..................................................................................................................................................12 Chain drive ...................................................................................................................................................................14 Balance shafts .............................................................................................................................................................15 Auxiliaries mounting bracket .....................................................................................................................................16 Cylinder head ..............................................................................................................................................................18 Integral exhaust manifold .........................................................................................................................................21 Positive crankcase ventilation ...................................................................................................................................23Oil supply............................................................................................ 28System overview .........................................................................................................................................................28 Oil supply .....................................................................................................................................................................30 Oil filler cap .................................................................................................................................................................32 Switchable piston cooling jets ...................................................................................................................................32Cooling system................................................................................... 34System overview .........................................................................................................................................................34 Innovative Thermal Management (ITM) ...................................................................................................................36Air supply and charging...................................................................... 49System overview .........................................................................................................................................................49 Air routing system for transversely mounted engines ............................................................................................50 Air routing system for longitudinal mounted engines ............................................................................................51 Intake manifold ..........................................................................................................................................................52 Turbocharger ...............................................................................................................................................................53Fuel system........................................................................................ 57System overview .........................................................................................................................................................57 Mixture formation / dual injection system ...............................................................................................................58 Operating modes ........................................................................................................................................................59Engine management system.............................................................. 62System overview example – 1.8l TFSI engine ..........................................................................................................62 Differences between 1.8L longitudinally and transversely mounted engines ......................................................64 Differences between components in the engines with 1.8 l and 2.0 l displacement ...........................................65 Component differences for the 2015 Audi S3 .........................................................................................................66 Differences between the exhaust turbochargers ....................................................................................................67 Differences between combustion methods .............................................................................................................68Special tools....................................................................................... 69 Self Study Programs........................................................................... 70 Knowledge Assessment..................................................................... 713This eSSP contains video links which you can use to access interactive media.This eSelf Study Program teaches a basic knowledge of the design and functions of new models, new automotive components or technologies. It is not a Repair Manual! All values given are intended as a guideline only. For maintenance and repair work, always refer to the current technical literature.NoteReference4IntroductionThe launch of the new 1.8L and 2.0L TFSI engines marks the beginning for the third generation of the successful EA888 four cylinder engine family from Audi. The motives for this development are increasingly stringent exhaust emission standards, better fuel economy and reduced CO2 emissions. To achieve these goals, the engines have been completely revised. This “global engine” is manufactured at Audi’s Hungarian plant in Györ; in Silao, Mexico; Shanghai and Dallan China. In the future it will also be produced in Changchun. Like the second generation versions of this engine, it is available in both 1.8L and 2.0L displacements. It is used for a variety of vehicle platforms and Group brands and is available in a wide range of power ratings. Another design requirement was that the engines be suitable for use in all markets, including those where low grade fuel is prevalent. Please note: Some illustrations of the 1.8L engine in this eSelf-Study Program are for the world-wide market. With the North American introduction of the third generation EA888 engines, the 1.8L engine will not have a continuously adjustable exhaust camshaft nor AVS. Learning objectives of this eSelf Study Program: This eSelf-Study Program introduces you to the technology of the third generation of EA888 4 cylinder engines. Upon completing this eSelf-Study Program, you will be able to answer the following questions:• • • What are the key technical modifications behind the development of the EA888 engine family? How do the innovative, new technologies work? What changes do the 1.8L and 2.0L engines bring to customer service?606_001ReferenceFor a detailed technical description of the first generation engine, please refer to eSelf-Study Program 921703, The Audi 2.0 Liter Chain-driven TFSI Engine.ReferenceTo find more about the modifications to the first and second generation engines, please refer to eSelf-Study Program 922903, The 2.0L 4V TFSI Engine with AVS.5Development goalsThe main goals for developing the third generation of the EA888 engine family were to meet more stringent exhaust emission standards and provide compatibility of the engine with various modular platforms. The engineers in Ingolstadt placed special emphasis on the following priorities during the development cycle: The following innovative, new technologies are featured:• • • • Exhaust manifold integrated into the cylinder head Dual injection system with direct and port injection** New, compact turbocharger module with cast steel turbine housing, electrical wastegate actuator and oxygen sensor upstream of the turbine Innovative Thermal Management system with fully electronic coolant temperature control• • • • A high proportion of identical parts for all engine versions Reducing engine weight Minimizing intra-engine friction Increasing power output and torque in conjunction with good fuel economyModular adaptationTo use the third generation of the EA888 engine family as a "global engine" in the modular longitudinal application (MLB) and the modular transverse application (MQB), it was necessary to revise its dimensions, mounting and connecting points. Engine mounts and a dipstick are used if the engine is transversely mounted. If the engine is longitudinally mounted, use is made of engine supports and a sealing cap in place of a dipstick.CO2 reductionTo meet emission limits while reducing CO2 output, the following design modifications have been made: Downsizing/downspeeding* Friction and weight reduction • Balance shafts partially mounted in needle bearings • Smaller main crankshaft bearing diameter • Lower oil level • Reduced tensioning force in the auxiliary drive Cylinder head • Cylinder head with Integrated Exhaust Manifold (IEM) • Weight-reduced exhaust turbocharger housing • Electrical wastegate actuator Injection • FSI and MPI fuel injectors** Thermal management • Rotary slide valve controlReducing frictionThe chain tensioners have been optimized for the reduced oil pressure. In addition to this, the tensioning force of the chains has been reduced, in turn reducing friction. Also, the crankshafts are made with smaller main bearing diameters which produce less friction. The poly-Vee belt drive configuration is identical for longitudinal and transverse mounted engines. However, the alternators and A/C compressors are model-dependent.* The term downspeeding is used to describe the reduction in engine speed achieved by altering the overall transmission ratio. Use of a drive ratio optimized for fuel efficiency makes it possible to achieve reductions in fuel consumption similar to those achievable by reducing engine displacement. The higher power output and average pressure level of turbocharged engines allows the operating point to be shifted towards lower engine speeds and higher engine loads. This means that the engine can be operated in an rpm range that is more favorable in terms of fuel economy. Downspeeding concepts generally go hand in hand with downsizing concepts - a combination particularly well suited to turbocharged direct injection gasoline engines. ** The initial offering of the 3rd generation engine in the North American market will be equipped only with FSI. The dual injection system with both MPI and FSI will be introduced in later models.6Brief technical descriptionEngine type • Four-cylinder in-line gasoline engine with direct injection and MPI* • Exhaust turbocharging with charge air cooling • Chain driven camshafts • Balance shafts - partially supported by needle bearings Valve control • Four valves per cylinder, double overhead camshafts • Continuous intake and exhaust camshaft adjustment on the 2.0L engine • Continuous intake camshaft adjustment on the 1.8L engine • Audi valvelift system (only on the exhaust camshaft of 2.0L version in the North American market) Engine Management • Electronic engine management system with EPC • Combined direct and port injection systems* • Adaptive O2 sensor control • Mapped ignition with high voltage ignition coils • Cylinder-selective adaptive knock control * The initial offering of the 3rd generation engine in the North American market will be equipped only with FSI. The dual injection system with both MPI and FSI may be introduced in later models.Animation showing the overall engine.606_0577Technical features1.8l TFSI engineEngine code Installation position Displacement cu in (cm3) Power output at rpm Torque at rpm Bore Stroke Compression ratio Main crankshaft bearing diameter Engine management system Fuel type Emissions standard Firing Order Knock control Turbocharging Exhaust gas recirculation Intake manifold flaps Intake camshaft adjustment - continuous Exhaust camshaft adjustment - continuous High pressure injectors (FSI) Injectors in the intake manifold (MPI) Secondary air system Audi valvelift system - for exhaust valves Rotary slide valve Regulated oil pump Tumble flaps CNSB transverse 109.7 (1798) 170 hp at 5100 - 6200 (125 kW at 5100 - 6200) 184 lb ft at 1250 - 5000 (250 Nm at 1250 - 5000) 3.24 in (82.5 mm) 3.31 in (84.1 mm) 9.6 : 1 1.88 in (48 mm) Simos 12 Premium 91 AKI SULEV 1–3–4–2 yes yes internal (camshaft adjustment) yes yes no yes no yes no yes yes yes1.8L & 2.0L engines overview82.0l TFSI engineEngine code Installation position Displacement Power output Torque at rpm Bore Stroke Compression ratio Main crankshaft bearing diameter in mm Engine management system Fuel type Emissions standard Firing order Knock control Turbocharging Exhaust gas recirculation Intake manifold flaps Intake camshaft adjustment - continuous Exhaust camshaft adjustment - continuous High pressure injectors (FSI) Injectors in the intake manifold (MPI) Secondary air system Audi valvelift system - for exhaust valves Rotary slide valve Regulated oil pump Tumble flaps Drumble1)CNTA longitudinal 121.0 cu in (1983 cm3) 220 hp at 4500 - 6250 (162 kW at 4500 - 6250) 258 lb ft at 1500 - 4500 (350 Nm at 1500 - 4500) 3.24 in (82.5 mm) 3.65 in (92.8 mm) 9.6 : 1 52 Simos 12 Premium 91 AKI SULEV 1–3–4–2 yes yes internal (camshaft adjustment) yes yes yes yes no yes yes yes yes no yesCYFB transverse 121.0 cu in (1983 cm3) 285 hp at 5500 - 6200 (206 kW at 5500 - 6200) 280 lb ft at 1800 - 5500 (380 Nm at 1800 - 5500) 3.24 in (82.5 mm) 3.65 in (92.8 mm) 9.3 : 1 52 Simos 12 Premium 91 AKI LEV3 1–3–4–2 yes yes internal (camshaft adjustment) yes yes yes yes no yes yes yes yes no yes1.8L & 2.0L engines overview1)Please see page 649Engine mechanicalsOverviewIn addition to significantly reducing the weight of the cylinder block, a second cooling-side oil gallery has been developed to accommodate the electrically switchable piston cooling jets. The cross-sections of the coolant and oil return lines have been modified and the position of the knock sensors has also been optimized. The balance shafts are now partially supported by needle bearings to reduce friction and ensure their robustness for start-stop or hybrid applications. The weight of the balance shafts has also been reduced which lowers the inertia required to move them. The oil return line on the "hot" side of the engine has been completely reconfigured.Weight saving measures (1.8l TFSI engine)The third generation of the EA888 engine family delivers a total weight saving of approximately 17.1 lb (7.8 kg). To achieve these savings, the following components have been modified or are used for the first time:• • • • Thin-walled cylinder block Integrated coarse oil separator Cylinder head and turbocharger Crankshaft (with smaller main bearing diameters and four counterweights)• • • • Die cast aluminium oil pan top section (including aluminium bolts) Plastic oil pan bottom section Aluminium bolts Balance shaftsCylinder blockThe cylinder block has been significantly revised to save weight. The wall thickness has been reduced from approximately 0.13 in (3.5 mm) to 0.11 in (3.0 mm). In addition, the coarse oil separator has been integrated with the block. These modifications result in a weight saving of approximately 5.29 lb (2.4 kg) compared to the second generation engines. Other modifications are: • A second pressurized cooling-side oil gallery for the electrically switchable piston cooling jets • Modified coolant and oil return line cross-sections • Optimized, long coolant jacket • Oil cooler supply via cylinder head coolant return line • Optimized knock sensor positioningsSealingBoth the timing chain cover and a sealing flange on the output side of the cylinder block are sealed using a liquid sealant.10OverviewTiming chain coverKnock sensor 1 G61Oil Pressure Switch Level 3 F447 Sealing flange, power output side (attached with aluminum bolts)Engine Speed Sensor G28 Cast iron cylinder blockOil pan top section with baffle plate Oil Pressure Regulation Valve N428Regulated oil pumpHoneycomb insertSeal Oil Level Thermal Sensor G266Oil pan bottom section606_028Oil panOil pan top section The oil pan top section is made from die cast aluminium. The oil pump and the honeycomb insert for oil intake and oil return are integral with the top section. The oil pan top section also accommodates the pressurized oil galleries and the two-stage oil pump control valve. It is sealed off from the cylinder block with a liquid sealant and attached by aluminium bolts. To enhance the acoustic characteristics of the engine assembly, the upper main bearing supports are integral with the top section of the oil pan.11Oil pan bottom section The oil pan bottom section is made from plastic. This provides a weight savings of approximately 2.2 lb (1 kg). It is sealed to the upper oil pan with a rubber gasket and attached with steel bolts. Oil Level Thermal Sensor G266 is integrated with the oil pan bottom section. The oil drain plug is made from plastic (bayonet lock).Crankshaft assemblyReducing weight and frictional losses was a main developmental goal.PistonSnap ringWrist pinConnecting rod (cracked lower end)Upper connecting rodbearing shellCrankshaftLower connecting rod bearing shell606_030Connecting rod bearing capAnimation showing the crankshaft assembly and sprocket chain drive, including the drive mechanism for the regulated oil pump and engine coolant pump.12PistonPiston clearance has been increased in order to reduce friction during the warm-up phase. A wear-resistant piston skirt coating is also used. Upper piston ring = taper face ring / on 2.0l engines Rectangular ring, asymmetrically barrelled Middle piston ring = taper face ring Upper piston ring = oil control ring (two piece, double bevelled spiral expander ring)Connecting rods/wrist pinsThe connecting rods are cracked at the large end. A significant modification is the elimination of the bronze bushing in the connecting rod small end. The connecting rod is fitted to the wrist pin without using a bushing by a special process patented by Audi AG. The wrist pin is floating and rides directly on the piston without any bushings. A special surface coating known as DLC is applied to the wrist pin. DLC stands for Diamond like Carbon, an amorphous carbon. DLC strata are very hard and are noted for having very low dry coefficients of friction. They can be identified by their glossy, black-gray surface.CrankshaftCompared to the second generation engine, the main bearing diameters of the crankshaft have been reduced from 2.04 in (52 mm) to 1.88 in (48 mm), and the number of counterweights reduced from eight to four. This has reduced the weight of the crankshaft by 3.5 lb (1.6 kg). The upper and lower main bearing shells are a two-layer lead-free composition. This ensures that the crankshaft is suitable for start-stop operation.Cradle supportThe upper oil pan is bolted to the lower main bearing caps. This modification helps reduce vibration and noise thus enhancing driver comfort.Cylinder blockCradle supportOil pan top sectionBolted from below Cross bolted at side606_02713Chain driveThe basic configuration of the chain drive system has been adopted from the second generation engine. However, new design parameters were implemented. Because of the reduction in friction of the drive assemblies, less power is needed to drive the chain mechanism. The chain tensioners have been adapted to operate at lower oil pressures. There are new chain assembly installation procedures and special tools required for the third generation engine. In addition, an adaptation procedure must be performed using the Scan Tool after doing work on the chain drive. The adaptation entails making measurements to establish allowable tolerances needed for diagnostic Test Plans.Exhaust camshaft adjuster (only on the 2.0L version for the North American market)Exhaust camshaft with Audi valvelift High pressure fuel pump system (AVS) (only on the 2.0L version for the North American market)Intake camshaft adjusterChain drive606_002Regulated oil pumpBalance shaftMain coolant pump14Balance shaftsIn addition to a reduction in overall mass, the balance shafts are now partially supported by needle bearings. This has reduced friction; especially at lower oil temperatures. This modification also increases the suitability of the components for use in start-stop or hybrid applications.Ring Needle bearingNeedle cageSliding railRingIdler gear Balance shaft drive chainSliding railCrankshaft sprocket Tensioning rail Bolt-in tensioner606_02915Auxiliaries mounting bracketOil filter and oil cooler holders are integrated into the engine auxiliaries mounting bracket. The auxiliaries mounting bracket contains oil ducts and coolant ducts routed to the oil cooler. The oil pressure switch, the electrical switching valve of the piston cooling jets and the poly-V belt tensioner are integrated in the bracket. The oil filter cartridge is accessible from above. To ensure that no oil is discharged when changing the filter, a sealing element is opened when the filter is released, allowing the oil from the filter to flow back into the oil pan.Design (shown using the transverse mounted 1.8l TFSI engine)Oil ductsOil supply line from oil cooler to oil filter and engineOil filter cartridgeOil Pressure Switch F22To the mechanical valve of the piston cooling jetsPiston Cooling Nozzle Control Valve N522 Oil supply to the engineReduced Oil Pressure Switch F378Oil return duct to oil pan for: −− venting the mechanical valve of the piston cooling jets −− draining off oil when changing the oil filter606_026Oil supply from the oil pumpPoly V-belt tensionerOil supply to the piston cooling jets Cooling jet switching valve vent Oil supply to the engine oil cooler16Coolant ductsThe oil supply line for the oil cooler is also integrated into the auxiliaries mounting bracket.Engine oil coolerFrom engine To Engine Temperature Control Actuator N493606_05517Cylinder headThe cylinder head is a completely new design. It features an integral exhaust cooling and routing system.Camshaft Adjustment Actuators F366 - F373Ignition Coils with Power Output Stage N70, N127, N291, N292Exhaust camshaft with Audi valvelift systemCamshaft adjuster IntakeIntegrated cooling ductsExhaust gas ducts to turbochargerCamshaft adjuster Exhaust (2.0L engine only)606_006Note Only the 2.0L engine will have a continuously adjustable exhaust camshaft and AVS at the introduction of this engine in North America.ReferenceTo learn more about the variable valve timing system, refer to eSelf-Study Program 921103, The Audi 3.0L V6 Engine.18Design123456 7981011 1213141516 16 18606_03117Key:1 2 3 4 5 6 7 8 9 Camshaft Position Sensor 3 G300 Cylinder head cover Camshaft Adjustment Actuators F366 - F373 (2.0L only) Intake camshaft Intake camshaft adjuster Roller-type cam follower Support element Intake valve Exhaust camshaft 10 11 12 13 14 15 16 17 18 Exhaust camshaft adjuster (2.0L engine only) Exhaust valve Camshaft Position Sensor G40 Port dividers Engine Coolant Temperature Sensor G62 Cylinder head Freeze plug Integral exhaust manifold stud Cylinder head gasket19SealingThe cylinder head cover is attached with steel bolts and sealed with a liquid sealant. The cylinder head gasket is two layer metal gasket.Audi valvelift system (AVS)The Audi valve lift system has been developed to optimize the change cycles of the dual fuel injection system. AVS is used when changing between FSI and MPI operation of the engine. Initially it will only be installed on the exhaust camshaft of the 2.0L version of the EA888 3rd generation engine even though the dual injection system will not be utilized.Camshaft adjusterAnother key modification is the use of a camshaft adjuster on the exhaust camshaft. This maximizes the scope for charge cycle management. The AVS system and the exhaust camshaft adjustment make it possible to adapt to the various charge cycle requirements at full and partial throttle. The result is rapid torque delivery. The high torque level across a wide rpm range allows the transmission ratios to be adapted differently (downspeeding). This improves fuel economy.Other modifications:• • • • • • • Long spark plug threads New ignition coils (retained by bolts, discrete ground wires) Weight-optimized camshafts Optimized roller cam followers (for reduced friction) Reduced spring forces in valve gear New oil filler cap integrated into the upper chain case Engine Coolant Temperature Sensor G62 integrated into the cylinder head (ITM)• • • • • Repositioned high pressure fuel pump Improved fine oil separator The turbine housing of the exhaust turbocharger is bolted directly to the cylinder head Optimization of the intake ports Improvement of the fuel injection components including sound insulationNote There are also several changes relevant to assembly work on the cylinder head. For a detailed description of the procedure, please refer to the relevant repair information.20Integral exhaust manifoldA cooled exhaust manifold with cylinder sequence separation is directly integrated with the cylinder head. The use of this manifold significantly lowers the exhaust temperature upstream of the turbine when compared to a conventional manifold layout. In addition, a highly heat resistant turbocharger is used. Because of the new manifold design, there is no longer a need for full throttle mixture enrichment to protect the turbocharger turbine during high speed engine operation. This improves fuel economy during normal operation and when driving in a more aggressive, sporty manner. The integral exhaust manifold facilitates rapid coolant heating and therefore, is a key part of the thermal management system.Exhaust ports The exhaust ports are designed so that exhaust gases from one cylinder do not interfere with the purging process of other cylinders. The full energy of the exhaust gas flow is available for driving the turbocharger. The exhaust ports of cylinders 1 and 4 as well as cylinders 2 and 3 converge at the transition to the turbocharger.Integral exhaust manifoldExhaust gas ports to the turbochargerTurbocharger module606_00721Cooling of the integral exhaust manifoldThe integral exhaust manifold facilitates rapid heating of the coolant and, therefore, is an integral part of the thermal management system. During the warm-up phase, heat is transferred to the coolant within a very short period of time. This heat is directly utilized to heat the engine and passenger compartment. Due to the reduced heat loss, the downstream components - oxygen sensor, turbocharger and catalytic converter - are able to reach their optimal operating temperature more quickly. The system goes into cooling mode even after a short warm-up phase. This is necessary because the coolant in proximity to the integral exhaust manifold would otherwise boil off very quickly. For this reason, Engine Coolant Temperature Sensor G62 is installed at the hottest point in the cylinder head.Intake sideMain water jacketUpper coolant tractLower coolant tractExhaust gas duct with flange connecting to turbochargerExhaust side606_032Animation showing the cylinder head and the integral exhaust manifold.22Positive crankcase ventilationThe positive crankcase ventilation system has also been systematically improved. The cylinder block pressure to ambient air pressure ratio is configured for a high pressure gradient. A strong emphasis has been placed on reducing the number of components. On the exterior of the engine, for example, there is now only one pipe for the discharge of cleaned blow-by gases. The system comprises the following components: • Coarse oil separator integrated with cylinder block • Fine oil separator module, bolted onto the cylinder head cover • Hose for the discharge of cleaned blow-by gases • Oil return line in the cylinder block with shutoff valve in the oil pan honeycomb insertEntry of blow-by gases into the intake manifold module (in naturally aspirated mode) Entry of blow-by gases into the turbocharger (in charging mode) Fine oil separator moduleOil return duct from the fine oil separatorOil return line shut-off valve Coarse oil separator for the fine oil separator (below the oil level in the oil pan)Oil return duct from the fine oil separator (below the oil level in the oil pan)606_04323Coarse oil separationThe coarse oil separator function is an integral part of the cylinder block. A portion of the oil is separated by changing the direction of oil flow in a labyrinth. The separated oil returns to the oil pan via the return duct in the cylinder block. The end of the duct is below the oil level.Fine oil separationThe coarsely cleaned blow-by gases flow from the cylinder block into the fine oil separator module through a duct in the cylinder head. Here, the gases are cleaned in a cyclone separator. The separated oil from the cyclone separator returns to the oil pan through a separate duct in the cylinder block. The end of this duct is below the oil level. A shutoff valve prevents oil from being drawn in from the oil pan in unfavorable pressure conditions. A sporty driving style (high transverse acceleration) could potentially expose the immersed oil return line because of the oil sloshing inside the oil pan. In this case, too, the shutoff valve keeps the oil return line closed. The shutoff valve is a shutter-type valve. The cleaned blow-by gases are directed into the combustion chamber via the single-stage pressure control valve. The pressure control valve is rated for a pressure difference of -1.45 psi (-100mBar) relative to the ambient air. The point at which the blow-by gases are admitted into the combustion chamber is dictated by the pressure ratio in the air supply system.Bypass valve opens at excessively high blow-by flow rates (very high engine speed) oil is also separated here by the high flow ratePressure control valveConnection to carbon canister606_045Blow-by duct from the cylinder block and cylinder headCyclone separatorBlow-by line to turbocharger (charging mode)24Supply of cleaned blow-by gases to the combustion chamberAfter the blow-by gases have been cleaned of fine oil droplets and allowed to flow through the pressure control valve, they are admitted into the combustion chamber. Gas flow is controlled automatically by self-actuating non-return valves integrated into the fine oil separator module. The non-return valves return to their initial position when the engine is shut off. The non-return valve facing the exhaust turbocharger is open, while the non-return valve facing the intake manifold is closed.Faulty installation detection Emission regulations require that safeguards be provided to detect faulty installation of these components. If the venting line on the crankcase breather module is not installed (or not properly installed) an installation detection contact opens. This contact is connected directly to the air intake side of the cylinder head. The engine immediately begins to induct unmetered air which is detected by the oxygen sensors.Full throttle operation (charging mode) Since pressure is now present throughout the charge air tract, non-return valve 1 closes. The difference between the pressure inside the crankcase and the pressure on the intake side of the turbocharger causes non-return valve 2 to open. The cleaned blow-by gases are inducted by the compressor.Bypass valveCyclone separatorNon-return valve 2 (open)Non-return valve 1 (closed)606_047Blow-by passage to turbocharger (charging mode)25Idle and partial throttle operation (naturally aspirated mode) In naturally aspirated mode, non-return valve 1 is opened by the vacuum present in the intake manifold and non-return valve 2 is closed. The cleaned blow-by gases are admitted directly into the combustion chamber via the intake manifold.Blow-by gas intakePressure control valveBlow-by passage to intake manifold (naturally aspirated mode)606_046PCV valveNon-return valve 2 (closed)Non-return valve 1 (open)26Positive crankcase ventilationThe crankcase breather is installed in a module on the camshaft cover together with the fine oil separator and the pressure regulator. The crankcase is vented via the venting line connected upstream of the turbine and a calibrated port in the crankcase breather valve. The system is therefore designed in such a way that it is only vented when the engine is running in naturally aspirated mode.Calibrated bore for positive crankcase ventilation PCV valve diaphragm (removed)Connection to carbon canisterCyclone separatorBlow-by line to intake manifold (naturally aspirated mode)Blow-by gas intake606_08327Oil supplySystem overviewKey: A B C D E F 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 23 24 25 26 27 28 29 30 Camshaft bearing Support element Balancer shaft bearing Exhaust balancer shaft bearing 1 Connecting rod Main bearings 1 – 5Bearing bridge A13Exhaust Camshaft Adjustment Valve 1 N318 Hydraulic vane cell adjuster (exhaust) Non-return valve, integrated. into bearing bridge Mesh oil filter Camshaft Adjustment Valve 1 N205 Hydraulic vane cell adjuster (intake) Non-return valve, integrated into cyl. head Fine oil separator Vacuum pump Flow restrictor Lubrication of cam for high pressure fuel pump Oil cooler Non-return valve, integrated into oil filter Oil filter Oil drain valve Oil Pressure Switch F22 33.3 - 43.5 psi (2.3 - 3.0 bar) Reduced Oil Pressure Switch F378 7.25 - 11.6 psi (0.5 - 0.8 bar) Piston Cooling Nozzle Control Valve N522 Mechanical switching valve Chain tensioner for balancer shafts Chain tensioner for timing gearAuxiliaries mounting bracket 12 13 14 6 5 2A43 A 422 Turbocharger Coarse oil separator Oil Pressure Switch Level 3 F447 Lubrication of gear step Oil Level Thermal Sensor G266 Cold start valve Non-return valve, integrated into oil pump Regulated oil pump Oil Pressure Regulation Valve N42815 16 171819High pressure circuit Low pressure circuitOil pan top section 2829 30 27 26 4 Oil pan bottom section288 Oil channelsAAAAA94 B B B B B B B B10 11 Vacuum pumpBBBBBBBBA 7AAACylinder head202122CDECEECE23FFFFF24 4 4C 25CCCylinder block606_01829Oil supplyThe engine lubrication system has been redesigned. The main points are: Together, these modifications have reduced friction within the engine assembly thus improving fuel economy still further.• • • • • Optimization of the pressure ducts in the oil system, reducing pressure losses while simultaneously increasing volume Reduction of pressure losses in the pressurized oil galleries Extension of the rpm range in the low pressure stage Oil pressure reduction in the low pressure stage Switchable piston cooling jetsOil Pressure Switch Level 3 F447 Oil cooler Oil filterReduced Oil Pressure Switch F378Oil Pressure Switch F22Piston Cooling Nozzle Control Valve N522Auxiliaries mounting bracketOil Pressure Regulation Valve N428Regulated oil pump606_003Piston cooling jetRaw oil Clean oil Switchable piston cooling jetsModifications to the oil pump: • Modified pressure level • Higher efficiency • Modifications to the hydraulic control system30Regulated oil pumpThe functional principle of the engine oil pump is similar to that of the second generation engine with the following differences:• • The hydraulic control system within the pump has been improved, enabling the pump to control oil flow with even greater precision. The pump drive ratios have been modified (i = 0.96) so that the pump now runs more slowly.606_033CoverCold start valveDisplacement unitControl pistonControl springDriven shaftRetention valveDrive shaft with drive pump gear Driven pump gear (axially displaceable)Compression spring of displacement unitPump housingIntakeMesh oil filter606_034ReferenceTo find out more about the function and design of the regulated oil pump, refer to eSelf-Study Program 922903, The 2.0L 4V TFSI Engine with AVS.31Oil filler capA new style engine oil filler cap is installed on the camshaft chain cover. It has been design to ease the opening and closing action and seal the engine bay from the environment in a safe, oil-tight manner. The seal and bayonet lock of the new style cap are functionally separate. The sealing face of the elastomer rectangular seal is smaller. No relative movement occurs between the seal and the camshaft chain cover when it is installed. This minimizes the actuation forces. The bayonet lock secures the cap by turning at 90 degree intervals.Top part of oil filler cap with bayonet lockSpringBottom part of oil filler capRectangular seal606_082Switchable piston cooling jetsThe switchable piston cooling jets system includes the following components: It is not necessary to cool the piston crowns in every operating situation. By replacing the previously spring controlled cooling jets with electrically control jets and selectively shutting them off, it is possible to reduce the overall oil pressure level. This is turn reduces the load on the engine oil pump and improves fuel economy.• • • • • Additional pressurized oil duct in cylinder block New piston cooling jets without spring valves; there are jets with two different internal diameters (the jets of the 1.8l TFSI engines have smaller diameters). Oil Pressure Switch Level 3 F447 Piston Cooling Nozzle Control Valve N522 Mechanical switching valvePiston cooling jet control The piston cooling jets are activated only when required. This calculation is made on the basis of a special map stored in the engine control module . The piston cooling jets can be activated both in the low and high pressure stages. The key calculation factors are:• • • Engine load Engine speed Calculated oil temperature258 lb ft221 lb ft184 lb ftTorque147 lb ft110 lb ft74 lb ft37 lb ft606_019Engine speed [rpm]Piston cooling switched off - oil temperature 122 °F (50 °C)32Piston cooling switched off - oil temperature 122 °F (50 °C)Piston cooling jets deactivated Piston Cooling Nozzle Control Module N522 is energized by the Engine Control Module. When energized, the control channel for the mechanical switching valve opens. Pressurized oil acts directly on both sides of the piston of the mechanical switching valve. The spring displaces the valve and closes the passage to the oil gallery of the piston cooling jets.Piston cooling jets activated The piston cooling jets spray when N522 is de-energized. When N522 is de-energized, the control channel to the mechanical switching valve is no longer supplied oil pressure to both sides of the valve. The mechanical valve therefore moves and opens the duct to the oil gallery of the piston cooling jets. The spring in the switching valve is pre-tensioned. The spring force keeps the oil gallery to the piston cooling jets shut at oil pressures of 13.0 psi (0.9 bar) or higher. To enable the switching valve to immediately return to its initial position after N522 is de-energized, the oil from the control piston must drain off quickly. There is a separate oil passage which allows the oil to drain without pressure into the engine oil pan. This is the same oil passage that oil drains into when replacing the oil filter.Reduced Oil Pressure Switch F378 Oil filter mandrel Oil gallery to the piston cooling jets closedOil gallery to the piston cooling jets openControl channel606_004Piston Cooling Nozzle Control Valve N522, energizedMechanical switching valve, shuts off the passage to the oil gallery of the piston cooling jets606_005Piston Cooling Nozzle Control Valve N522, de-energizedSwitching valve venting lineMechanical switching valve, opens the port to the oil gallery of the piston cooling jetsFunction monitoring When the piston cooling jets are switched on, the contact in Oil Pressure Switch Level 3 F447 closes. The switch is located at the end of the oil gallery for the piston cooling jets (see page 30, Fig. 606_003). The following faults can be detected by the oil pressure switch: • No oil pressure is present at the piston cooling jets despite being requested • Faulty oil pressure switch • Oil pressure is present despite deactivation of piston cooling jets The following electrical faults can be detected in the control valve for the piston cooling jets: • Open circuit; piston cooling jets are always on • Short circuit to ground; piston cooling is off • Short circuit to +; piston cooling is always on Faults resulting in loss of piston cooling lead to the following emergency running reactions: • Torque and engine speed are limited by the ECM • The regulated oil pump has no low oil pressure stage • A message indicating that the engine speed is limited to 4000 rpm is displayed in the DIS, a single acoustic signal sounds and the EPC lamp lights up33Cooling systemSystem overviewThe cooling system is adapted to match the vehicle specification and engine type. A distinction is made between longitudinal and transverse mounting, transmission version, and whether or not the vehicle is equipped with an auxiliary heater. Vehicles sold in the North American region will not have auxiliary heaters.Coolant circulationThe 1.8l TFSI is given here as an example. It is in the longitudinal mounted version with a manual transmission.Connections from and to heater heat exchanger 1Numbers from the key on page 35 have been added to the labels in the diagram.Rotary slide valve 2 8Rotary slide valve 1 8Coolant expansion tank 6Coolant Recirculation Pump V50 4Transmission heating connectionDucts of the integral exhaust manifoldTurbocharger 9606_009Engine oil cooler 11Radiator 15Note Auxiliary heaters are not available in the North American market.Note For vehicle-specific terminal diagrams, refer to the applicable repair information.341.8l TFSI longitudinal mounted engine with manual transmission*1234 5678910111213 1514606_023Cooled coolant Heated coolant ATF Key: 1 2 3 4 5 6 7 8 Passenger compartment heat exchanger Transmission gear oil cooler Climatronic Coolant Shut-off Valve N422 activated Coolant Recirculation Pump V50 Transmission Coolant Valve N488 Coolant expansion tank Engine Coolant Temperature Sensor G62 Engine Temperature Control Actuator N493 (rotary slide valves 1 and 2) 9 10 11 12 13 14 Exhaust turbocharger Integral exhaust manifold Engine oil cooler (heat exchanger) Coolant Fan V7 Coolant Fan 2 V177 Engine Coolant Temperature Sensor on Radiator G8315 Radiator* This configuration will be introduced in later Audi models and does not apply to the 2015 Audi A3.35Innovative Thermal Management (ITM)The complete coolant circuit was revised during development of the engine. The main emphasis was on rapid engine heating, reduction in fuel consumption by rapid and thermodynamically optimized engine temperature regulation, as well as heating of the vehicle interior when required. The two key components of the innovative thermal management system are the exhaust manifold integrated into the cylinder head (see "Cylinder head") and Engine Temperature Control Actuator N493 described below. It is installed as a module on the cooling side of the engine, together with the coolant pump.Coolant temperature at ambient temperature 68 °F (20 °C)265 lb ft (360 Nm) 236 lb ft (320 Nm) 205 lb ft (280 Nm) 177 lb ft (240 Nm) 147 lb ft (200 Nm) 118 lb ft (160 Nm) 88 lb ft (120 Nm) 59 lb ft (80 Nm) 29 lb ft (40 Nm)Key:185 °F (85 °C) 194 °F (90 °C) 203 °F (95 °C) 212 °F (100 °C) 221 °F (105 °C)Torque [Nm]606_040Engine speed [rpm]36Engine Temperature Control Actuator with rotary slide valve module and coolant pumpCoolant pump Supply line to radiatorN493Rotary slide valve 2Toothed belt drive gearToothed drive belt for coolant pump606_035Rotary slide valve 1Coolant pump drive gear Return line from radiator Return line from heater, turbocharger and transmissionCoverAnimation showing the ITM system and the function of the rotary slide.37Engine Temperature Control Actuator N493 (rotary slide valve)Engine Temperature Control Actuator N493 is identical for longitudinally and transversely mounted engines. It regulates coolant flow by means of two mechanically coupled rotary slide valves. The angular position of the rotary slide valves is regulated according to various maps stored in the ECM. Various switching positions can be implemented by configuring the rotary slide valves accordingly. This allows rapid heating of the engine, which, in turn, results in lower friction and improved fuel economy. In addition, variable engine operating temperatures between 185 °F - 225 °F (85 °C 107 °C) are possible.1234589671011606_036Key: 1 2 3 4 5 N493 with sender Connecting piece for radiator supply line Connecting piece to lube oil cooler connection Idler gear Rotary slide valve 2 6 7 8 9 10 11 38Shaft for rotary slide valve 1 Rotary slide valve housing Expanding element thermostat (fail-safe thermostat) Sealing package Connecting piece for return line from radiator Rotary slide valve 1Function of Engine Temperature Control Actuator N493 A DC electric motor drives the rotary slide valve. It is activated by a PWM signal (12V) from the Engine Control Module. The activation frequency is 1000 Hz. The activation signal is new. It is a digital signal with a configuration similar to that of a CAN signal. The motor is activated until rotary slide valve is in the position specified by the ECM. A positive activation signal causes the rotary slide valve to rotate in the “open” direction. This can be observed in the MVBs. The motor drives rotary slide valve 1 via a high reduction ratio worm gear. It controls the coolant flow in the engine oil cooler, cylinder head and the main radiator. The transmission cooler, turbocharger and heater return lines are unregulated. Rotary slide valve 2 is connected to rotary slide valve 1 via a lantern gear. The gear is designed in such a way that rotary slide valve 2 engages and disengages in defined angular positions of rotary slide valve 1. Rotary slide valve 2 (which opens the coolant flow through the cylinder block) begins to rotate when rotary slide valve 1 is in an angular position of approx. 145°. Rotary slide valve 1 disengages again in an angular position of approx. 85°. In this position, rotary slide valve 2 has completed its maximum rotation and the cylinder block cooling circuit is fully open. The movements of the rotary slide valve are limited by mechanical stops.The warmer the engine, the further the rotary slide valve rotates. This causes various channels to open into variable cross-sections.To determine the exact position of the rotary slide valve and to detect malfunctioning, a rotation angle sensor is mounted on the rotary slide valve control board. This sensor supplies a Single Edge Nibble Transmission (SENT) data protocol signal to the ECM. This type of signal can, in conjunction with the appropriate sensors, be used for digital data transfer as a replacement for analog interfaces. The position of rotary slide valve 1 can be seen in the MVBs.Engine outletEngine inletRotary slide valve 2DC adjustment motorSupply line to radiator606_010Return line from oil cooler Worm gearRotary slide valve 1Belt drive Coolant pump Return line from heater, turbocharger and transmission Return line from radiator39Engine warm-up and operation is divided into three phases of regulationAdjustment angleWarm-up and regulation over 160°After-run over a total of 95°Temperature control range for partial and full loadWarm-up range Switch on engine oil cooler Minivolume stream Static coolantAfter-run ranges522_107The following pages describe the engine temperature regulation from the warm-up range, the temperature control range and finally to the after-run range. This is a highly simplified representation and does not include the electrical drive of the Engine Temperature Control Actuator N493 or the main water pump drive.40Temperature regulation sequenceDuring warm-up, the engine runs through three phases: • Static coolant • Mini-volume stream • Enable engine oil coolerThe different phases are accomplished through the positions of the rotary valves. The objective is to use the energy generated by the fuel combustion to heat the engine as much as possible. However, if passenger compartment heating is required during the "static coolant" phase, heat energy is provided to the interior.TurbochargerNon-return valvesCylinder head with integrated exhaust manifold Passenger compartment heat exchangerCylinder blockAfter-run Coolant Pump V51Climatronic Coolant Engine oil cooler Shut-off Valve N422Rotary valve 2Rotary valve 1Coolant pump Engine Temperature Control ActuatorEmergency mode thermostatMain radiatorN493s522_09241Warm-up with static coolantTo keep the heat from the fuel combustion in the engine, Rotary valve 2 is closed. This interrupts the coolant flow from the engine coolant pump to the cylinder block. Rotary valve 1 blocks return from the engine oil cooler and the return from the main radiator. Climatronic Coolant Shut-off Valve N422 interrupts the coolant flow to the passenger compartment heat exchanger and Coolant After-run Pump V51 is not activated.V451 Engine block N422Rotary valve 2Rotary valve 1Main radiators522_092Warm-up with mini-volume flowTurbochargerThis control phase in the warm-up range protects the cylinder head and the turbocharger from overheating from the static coolant in the exhaust manifold. At a Rotary valve 1 angle position of 145°, Rotary valve 2 is engaged and begins to open. A small coolant flow begins through the cylinder block, the cylinder head and the turbocharger returning back to the rotary valve module and coolant pump.Rotary valve 2Rotary valve 1s522_09342Warm-up with mini-volume flow and heating in the vehicle interior If heating is required in the passenger compartment during this phase, N422 opens and After-run Coolant Pump V51 starts delivery. Rotary valve 2 temporarily interrupts the coolant flow to the cylinder block. The coolant is directed through the cylinder head, turbocharger and heat exchanger. This, however, causes the warm-up phase of the engine to take longer. N422 and V51 are also always activated to comply with requirements in the subsequent control ranges. The coolant flow to the engine block is reduced or blocked by rotary valve 2 as required.Engine block N422Heat exchangerV451Rotary valve 2s522_094Warm-up with map-controled engine activeIn this stage, the engine oil cooler is enabled during the warm-up phase of the engine. Rotary valve 1 moves to a 120° angle position opening the passage to the oil cooler. Because Rotary valve 2 is still engaged, it also turns more and enlarges the coolant flow through the cylinder block. A large amount of heat distribution occurs in the engine block and excess heat is discharged via the oil cooler.Engine blockRotary valve 2 Engine oil cooler Rotary valve 1s522_09543Temperature control rangeThe innovative thermal management moves seamlessly from the warm-up range to the temperature control range. Here, rotary valve module regulation is dynamic and depends on the engine load. To conduct excess heat away, the connection to the main radiator from the rotary valve module is opened. To do this, positions rotary valve 1 in an angle position of 0° and 85°, depending on how much heat has to be conducted away. At a rotary valve 1 angle position of 0° the connection to the main water cooler is fully opened.Rotary valve 2Rotary valve 1Main radiators522_096If the engine is running at a lower load and speed (partial load range), the thermal management adjusts the coolant temperature to 225 °F (107°C). Since the full cooling power is not required, rotary valve 1 temporarily closes the connection to the main radiator. If the temperature rises above this threshold value, the connection to the main radiator is opened again. Constant opening and closing is necessary to keep the temperature as much as possible at a constant 225 °F (107°C). When load and engine speed increase, coolant temperature is reduced to 185 °F (85 °C) (full load range) by first completely opening the connection to the main radiator.Rotary valve 2Rotary valve 1Main radiator s522_10244After-run range when switching off the engineTo prevent the coolant from boiling in the cylinder head and in the turbocharger when the engine is switched off, the ECM initiates an after-run function. It can be active for up to 15 minutes after the engine is switched off. During the after-run function, Rotary valve 1 of N493 is positioned at an angle between 160 degrees and 255 degrees. The greater the after-run requirement, the higher the angle position. At 255 degrees of opening angle, the passage to the return line of the main radiator is fully open so maximum heat is dissipated. Rotary valve 2 is in the after-run position and not engaged with Rotary valve 1. V51 circulates coolant through two sub-streams in the coolant circuit. One sub-stream flows over the cylinder head and back to V51. A second sub-stream flows via the turbocharger through Rotary valve 1 to the main radiator and also to After-run Coolant Pump V51. The cylinder block is not supplied with coolant in the run-on position.V451N422Rotary valve 2Rotary valve 1Main radiators522_10645Emergency running mode strategyIf the coolant temperature in N493 exceeds 235 °F (113 °C), the emergency thermostat opens a bypass to the main radiator. This allows the driver to continue driving the vehicle to a limited extent if N493 is defective. If the ECM doesn't receive feedback from N493, it moves Rotary valve 1 to a maximum engine cooling position regardless of engine load and operating temperature. If N493 should fail, for example, the electric motor fails or the rotary valve drive should jam, further measures are initiated:V451• A fault message is displayed in the instrument cluster and at the same time engine speed is limited to 4000 rpm. A warning tone is issued and the EPC is illuminated. The actual engine coolant temperature is also displayed in the instrument cluster. Climatronic Coolant Shut-off Valve N422 is opened. After-run Coolant Pump V51 is activated to ensure cylinder head cooling. A DTC is logged in the Engine Control Module.N422• • • • Rotary valve 2Rotary valve 1If the rotary valve position sensor signal is implausible or the sensor fails, the ECM activates Rotary valve 1 to a maximum cooling position as a failsafe.Emergency mode thermostat s522_097Vehicles with DSG transmissions On vehicles with DSG transmissions, the coolant circuit is expanded to include a transmission heat exchanger and Transmission Coolant Valve N488.Gear oil cooler Auxiliary radiator Coolant shut-off valve N82 s522_10146Functional diagram of Engine Temperature Control Actuator N493Connections1 2 3 4 5Sensor ground (connection in engine wiring harness) Sensor signal Sensor + (5 V connection in engine wiring loom) Actuator – Actuator +23451606_021Transmission Coolant Valve N488N488 controls the flow of warm coolant from the engine to the transmission gear oil cooler. When required, the solenoid valve is activated by the ECM. It is held open by mechanical spring force when not activated and closes when the engine is started. The coolant flow to the transmission opens at a coolant temperature of 176 °F (80 °C) and closes again at 194 °F (90 °C). This helps the manual transmission to attain its optimal friction temperature.Electrical connectionCoolant flow to the engineSolenoid coil606_022PistonCoolant flow to the cooler47Coolant Recirculation Pump V50This pump is used as a circulation pump for the passenger compartment heat exchanger in vehicles with longitudinally mounted engines. It is activated by Climatronic Control Module J255 via a PMW signal. It is diagnosed through J255. Function Coolant Recirculation Pump V50 is activated when the ignition is switched on depending on the coolant temperature and the desired interior temperature setting of Climatronic Control Module J255. When V50 is running, coolant is circulated between the engine and the passenger compartment heat exchanger.Climatronic Coolant Shut-off Valve N422N422 is installed on longitudinally mounted engines. The valve permits or prevents coolant flow to the passenger compartment heat exchanger. See page 35, figure 606_023. Function Climatronic Coolant Shut-off Valve N422 is identical to Transmission Coolant Shut-off Valve N488 (see previous page). It is open (allowing coolant flow) when it is not energized and closes (preventing coolant flow) when current is applied. It is opened by spring force and closes when the engine is started. The valve opens when the heating, run-on cooling and start-stop functions are activated. N422 is controlled by Climatronic Control Module J255 and requires adaptation using the VAS Scan Tool.Coolant Recirculation Pump V50606_056Coolant After-run Pump V51V51 is installed on vehicles with transversely mounted engines. It is identical to Coolant Recirculation Pump V50 used in vehicles with longitudinally mounted engines. It is activated by the ECM with a PWM signal after receiving a request from Climatronic Control Module J255. V51 also assists the engine coolant pump to increase coolant flow through the passenger compartment heat exchanger at defined engine speeds thus providing higher heating output. It also helps reduce turbocharger temperature more quickly which helps extend engine oil life.Coolant Shut-off Valve N82Coolant Shut-off Valve N82 is activated by the Engine Control Module. Depending on the requested temperature in the passenger compartment, N82 shuts off the coolant flow through the passenger compartment heat exchanger. This is done for example, to heat up the engine.48Air supply and chargingSystem overviewC A B DEV465N249FG31 N316 J338 G186 G187 G188Exhaust gases Intake air (vacuum) Charge air (charge pressure) Wastegate (charge pressure)GG336G42 with G71606_025Key: A B C D E F G Exhaust flow Exhaust turbocharger Air filter Fresh air flow Wastegate valve Charge air cooler Intake manifold flaps G31 Charge Air Pressure Sensor G42 Intake Air Temperature Sensor G71 Manifold Absolute Pressure Sensor G186 EPC Throttle Drive G187 EPC Throttle Drive Angle Sensor 1 G188 EPC Throttle Drive Angle Sensor 2 G336 Intake Manifold Runner Position Sensor J338 Throttle Valve Control Module N249 Turbocharger Recirculation Valve N316 Intake Manifold Runner Control Valve V465 Charge Pressure ActuatorNote The Charge Pressure Actuator V465 must be replaced after removing the lock nut from the linkage. After replacement, the charge pressure actuator must be adapted using the Scan Tool.49Air routing system for transversely mounted enginesTurbocharger (B)Turbocharger Recirculation Valve N249Charge Pressure Actuator V465Air filter (C)606_037Intake manifoldCharge air cooler (F) Intake Manifold Runner Control Valve N316Intake Manifold Runner Position Sensor G336Air intake (D)Intake Air Temperature Sensor G42 with Manifold Absolute Pressure Sensor G71 Throttle Valve Control Module J338Charge Pressure Sensor G3150Air routing system for longitudinal mounted enginesAir filterCharge Pressure Actuator V465TurbochargerIntake Manifold Runner Control Valve N316Intake Air Temperature Sensor G42 with Manifold Absolute Pressure Sensor G71 Throttle Valve Control Module J338Intake manifoldAir intakeIntake Manifold Runner Position Sensor G336Charge Pressure Sensor G31606_038Charge air cooler51Intake manifoldTo accommodate both FSI and MPI fuel injectors, a newly designed intake manifold was required. The manifold also has pan-shaped flaps to direct air flow in the intake duct. An angled, single piece stainless steel shaft maximizes the torsional rigidity of the flaps. At initial launch of these engines, the North American version will only have FSI injection. The shaft is actuated by Intake Manifold Runner Control Valve N316 using a vacuum motor based on signals from the ECM. The pan-shaped flaps are tensioned in the manifold in such a way to minimize excitation by the airflow.Fuel Metering Valve N290 High pressure pumpIntake Air Temperature Sensor G42 with Manifold Absolute Pressure Sensor G71Vacuum motor for intake manifold flapsMPI injectorsIntake Manifold Runner Position Sensor G336606_041FSI injectors Intake manifold flapsThrottle Valve Control Module J338Intake Manifold Runner Control Valve N316FSI injectors606_04252TurbochargerAn all new mono-scroll turbocharger is used on both the 1.8L and 2.0L versions of the third generation EA888 engine. It has the following features: The use of a mono-scroll turbocharger improves full throttle response, particularly at high engine speeds. Twin-scroll channeling of exhaust gases from the cylinder head outlets is continued to a point just short of the turbocharger turbine. The turbocharger uses a Mixed Flow Turbine design. A Mixed Flow Turbine is a compromise between a radial turbine and an axial turbine. Exhaust gases flow radially through the radial turbine wheel (leading edge is parallel to axis of rotation). Consequently, the turbine is suitable for handling low flow rates, such as those typical of passenger cars. On the other hand, exhaust gases flow axially through the axial turbine wheel (the inlet edge is at an angle of 90° relative to the axis of rotation). This turbine wheel is suitable for handling low flow rates, such as those typical of large displacement engines. Mixed Flow Turbines have a diagonal leading edge. Because this type of turbine has an additional axial impeller, which is ideal for high flow rates, a smaller impeller can also be used. The advantage of better response in the radial turbine is combined with the higher efficiency of the axial impeller in the upper rpm range.• • • • • • • • Electrical wastegate actuator (Charge Pressure Actuator V465 with Charge Pressure Actuator Position Sensor G581) Oxygen sensor upstream of turbine (Heated Oxygen Sensor G39) Compact cast steel turbine housing with twin-scroll inlet flanged directly onto the cylinder head Compressor housing with integrated pulsation silencer and Turbocharger Recirculation Valve N249 Temperature resistant Inconel turbine wheel rated for temperatures of up to 1796 °F (980 °C) Bearing housing with standard connections for oil and coolant Milled compressor wheel for higher speed resistance and better acoustics Turbine wheel configured as a Mixed Flow Turbine made from Inconel 713 °CMono-scroll turbines have only one