TECHNICAL DOCUMENTATION
SSP 920253 – The Audi 1,4l TFSI Engine

This PDF is currently unavailable.
Read document text
eSelf Study Program 920253The Audi 1.4l TFSI EngineiAudi of America, LLC Service Training Created in the U.S.A. Created 8/2015 Course Number 920253 ©2015 Audi of America, LLC All rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC. Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.This eSSP contains video links which you can use to access interactive media.Revision 1:8/2015iiIntroduction ...................................................................................... 1Brief technical description ........................................................................................................................................2 Power and torque specifications ..............................................................................................................................4Engine mechanicals............................................................................ 6Cylinder block .............................................................................................................................................................6 Crankshaft drive system and valve gear ..................................................................................................................7 Camshaft drive ...........................................................................................................................................................8 Crankcase ventilation ............................................................................................................................................. 10 Evaporative emission system ................................................................................................................................ 13 Cylinder head .......................................................................................................................................................... 14Oil supply.......................................................................................... 16Oil circulation system ............................................................................................................................................. 16 Regulated oil pump ................................................................................................................................................ 17 Sump ........................................................................................................................................................................ 19 Oil cooling ................................................................................................................................................................ 20Cooling system................................................................................. 21Introduction ............................................................................................................................................................ 21 System overview .................................................................................................................................................... 22 Thermostat ............................................................................................................................................................. 23 Coolant pump ......................................................................................................................................................... 23 Cylinder head cooling ............................................................................................................................................ 24 Intercooler .............................................................................................................................................................. 25Air intake and turbocharger systems................................................ 27Overview .................................................................................................................................................................. 27 Turbocharger ........................................................................................................................................................... 28Fuel system...................................................................................... 31Overview .................................................................................................................................................................. 31Exhaust system................................................................................ 32Overview .................................................................................................................................................................. 32 Catalytic converter .................................................................................................................................................. 33Engine management system............................................................ 34Sensors and actuators .......................................................................................................................................... 34 Engine speed sensor G28 ....................................................................................................................................... 36Appendix.......................................................................................... 38Special tools and workshop equipment ............................................................................................................... 38Self-study programs......................................................................... 40 Knowledge assessment.................................................................... 41This eSelf Study Program teaches a basic knowledge of the design and functions of new models, new automotive components or technologies. It is not a Repair Manual! All values given are intended as a guideline only. For maintenance and repair work, always refer to the current technical literature.NoteReferenceiiiivIntroductionThe 1.4l TFSI engine used in the A3 Sportback e-tron is from the EA211 series of 4-cylinder engines used by Audi worldwide. This is the first use of this engine in the North American market. It is derived from the EA111 series of 4-cylinder engines but has been further refined to be lighter, more fuel efficient, and reduce emissions. It is compactly dimensioned for vehicles using the cross-platform modular component set (MQB). In some markets, a selective cylinder shut-down capability that enables two of the four cylinders to be shut down when driving situations allow is employed. However, in the North American market this feature will not be used. The 1.4l TFSI engine develops 147 hp (110 kw) and is coupled to the e-machine (Electro-drive Drive Motor V141) and sixspeed DSG transmission 0DD.1.4l TFSI engine616_015aLearning objectives of this self-study program Upon completion of this Self-Study Program, you be able to answer the following questions: • How is the engine constructed? • How does the engine cooling system function? • How does the intake air and turbocharger system function?1Brief technical description• Four-cylinder in-line engine. • Four valves per cylinder, double overhead camshafts (DOHC). • FSI direct injection. • Cast aluminium cylinder block. • Turbocharger with indirect intercooler. • Intercooler integrated in intake manifold (air/coolant heat exchanger). • Belt driven camshafts. • Emission control system with ceramic catalytic converter and converter heating function using two-stage injection (homogeneity split). • Energy recovery system in over-run mode.1.4l TFSI engine(Engine with cylinder selective shut-down shown)616_0142Internal combustion engine and e-machine with transmissionElectro-drive Drive Motor V141 (e-machine)6-speed dual clutch transmission (S tronic)1.4l TFSI engine627_107Features Engine code Type Internal combustion engine output Electric motor output System output Torque of internal combustion engine Electric motor torque System torque Displacement in cm Stroke Bore Number of valves per cylinder Firing order Compression ratio Fuel type Turbocharging Engine management system Powertrain type Oxygen sensor control Mixture formation Emission standard3Specifications CUKB Four-cylinder in-line engine 150 hp (110 kW) at 5000 - 6000 rpm 102 hp (75 kW) at 2000 - 2300 rpm 150 kW 184 lb ft (250 Nm) at 1600 - 3500 rpm 243 lb ft (330 Nm) at 2200 rpm 258 lb ft (350 Nm) 1395 3.1 in (80 mm) 2.9 in (74.5 mm) 4 1–3–4–2 10 : 1 Premium 91 AKI Exhaust turbocharger Bosch MED 17.01.21 6-speed dual clutch transmission (S tronic) 1 sensor upstream of catalytic converter and 1 sensor downstream of catalytic converter Direct injection SULEV3Power and torque specificationsEA211 series 1.4l TFSI engine CUKB and Electro-drive Drive Motor V141 as used in the 2016 A3 Sportback e-tronTorque in Nm Internal combustion engine Electric motor System (15 seconds)Power in hp Internal combustion engine Electric motor System (15 seconds)295.0 lb ft (400 Nm)268.2 hp (200 kW)258.1 lb ft (350 Nm)234.6 hp (175 kW)221.21 lb ft (300 Nm)201.1 hp (150 kW)184.3 lb ft (250 Nm)167.6 hp (125 kW)147.5 lb ft (200 Nm)134.1 hp (100 kW)110.6 lb ft (150 Nm)100.5 hp (75 kW)73.7 lb ft (100 Nm)67 hp (50 kW)36.8 lb ft (50 Nm)33.5 hp (25 kW)Engine speed [rpm]627_0934Notes5Engine mechanicalsCylinder blockThe cylinder block is made of die-cast aluminum and is an open-deck design. The advantages and disadvantages of an open-deck design are: • It is easier and more economical to manufacture from the point of view of casting technology. • More efficient cooling of the upper, (and hotter) part of the cylinders compared with a closed-deck design • It is less rigid when compared to a closed-deck design. This is compensated by the use of a metal cylinder head gasket. • There is deformation of the cylinder liner when the cylinder head and cylinder block are bolted together. • The slight cylinder liner deformation is easily compensated by the piston rings (oil consumption is also lower). The engine oil galleries (both pressure and return) and those for crankcase venting are cast integral with the crankcase. This reduces the number of additional components and manufacturing complexity. Cast-iron cylinder liners The cast-iron cylinder liners are individually cast inside the cylinder block. Their outer surface is very rough which increases the surface area and improves heat transfer to the cylinder block. The roughness also forms a very good interlocking fit with the cylinder block.Knock Sensor 1 G61Aluminium cylinder block with open-deck designMain crankshaft bearingsOil baffle plateSump top sectionOil Level Thermal Sensor G266Sump bottom section616_0066Crankshaft drive system and valve gearThe crankshaft drive components have been designed with small moving masses and low friction as a priority. The connecting rods and pistons have been optimized for weight. The lightweight crankshaft with four counterweights, runs in five main bearings. The use of only four counterweights reduces the internal crankshaft forces and therefore the stress on the main bearings.Crankshaft drive and valve gear on 1.4l TFSI engineCamshaftsValves operated by roller-lever cam followersAluminium pistons with valve recessesLightweight trapezoidal connecting rodLightweight crankshaft with four counterweights616_019Pistons and connecting rodsThe pistons are made of die-cast aluminum. To reduce the thermal stresses, oil injectors spray engine oil onto the piston crown from underneath. The lightweight forged connecting rods have cracked big ends. The small end has a trapazoidal profile but does not have a pressurized oil supply. The aluminum pistons have a flat crown and have optimized for weight. The wrist pins are hollow.616_039NoteThe crankshaft must not be removed. For more information, please refer to ElsaPro.7Camshaft driveThe camshafts are driven by a toothed timing belt. The belt has a wear resistant Teflon coating which provides a long service life. The use of a timing belt results in lower friction and mechanical stresses on the timing gears as a whole. Lower vibration levels make for a smoother and quieter running engine. An automatic tensioning roller additionally helps to guide the timing belt by means of raised flanges. Special tools T10499 and T10500 are needed to relieve the tension on the belt during removal and installation procedures. A guide pulley and the crankshaft sprocket also help ensure the belt runs smoothly.Intake camshaft sprocket with vane adjuster (adjustment range of 50°) Exhaust camshaft sprocketTensioner pulleyGuide pulleyOil pump drive sprocketcamshaft drive sprocketOil pump drive gearThe oil pump is driven by a maintenance free toothed chain. No chain tensioner is installed. The drive sprocket for the oil pump is permanently attached to the crankshaft and cannot be removed.Toothed drive chain for oil pump616_020Oil pump sprocket8Timing belt coverThe timing belt is protected from dust and dirt by a three-piece timing belt cover. The aluminum center section of the timing belt cover also serves as an engine mounting point. During repairs that require the removal of the timing belt from the cylinder head, the center section of the cover can remain in place. There is sufficient room to tension the belt.Plastic cover with injection molded sealAluminum cover (engine mount)Plastic cover with injection molded seal616_0329Crankcase ventilationCleaned blow-by gases flow through channels in the cylinder block to the intake pipe upstream of the turbocharger or into the intake manifold downstream of the turbocharger. The oil vapors are removed by the plastic oil separator bolted to the cylinder block.Inlet of blow-by gases on intake side of turbocharger (at high engine speeds)Blow-by inlet pipeNon-return valve on turbochargerTurbochargerOil separatorThe gases flow from the crankcase into the oil separator. There, the large droplets of oil are separated by means of baffle plates and swirl channels in the coarse separator. Then the fine droplets are removed by large baffle plates in the fine separator.Coarse oil separatorSeparation chamber outlet InletConnecting pipe to intake manifold module with calibrated diameter. The calibration limits the flow volume. As a result the pressure regulating valve can be eliminated.Oil separator housing cover Fine oil separatorOil returnsOil return from oil separator to sump below oil level Separation chamber in crankcase10Non-return valvesThe non-return valves control recirculation of the cleaned blow-by gases based on the pressure conditions in the air intake system. If there is negative pressure in the intake manifold at idling or higher engine speeds, the vacuum effect opens the valve in the intake manifold module and closes the valve on the intake side of the turbocharger. If there is positive pressure in the intake manifold when the turbocharger is working, that pressure closes the valve in the intake manifold module. At the same time, the valve on the intake side of the turbocharger is opened by the pressure differential present. That means that the pressure on the intake side of the turbocharger is lower than the pressure inside the crankcase.Inlet point with non-return valve on intake side of turbochargerInlet point for fuel vapors from the EVAP system carbon canisterInternal routing of blow-by gases through channels in the cylinder block and cylinder headInlet point for blow-by gases downstream of turbocharger on intake manifold module (at low engine speeds)Throttle valveIntake point downstream of turbocharger on intake manifold moduleIntake manifoldNon-return valve Oil separator module on cylinder block Blow-by inlet pipe616_01711A non-return valve is located in the crankcase ventilation system. It allows fresh air to circulate and carry harmful condensation and fuel constituents from the cylinder block and oil sump. If there is sufficient negative pressure inside the engine, fresh air is passed from the clean side of the air filter into the engine and is subsequently fed back into the cylinders together with the blow-by gas.To achieve that, the non-return valve must open at the slightest degree of depression inside the engine. The routing of the hose may vary depending on the engine variant. The non-return valve in the cylinder head cover prevents the oil or unfiltered blow-by gas from entering the air filter and contaminating it.Hose connection on air filter boxNon-return valve616_04212Evaporative emission systemThe evaporative emission system of the 1.4l TFSI engine is similar to those used on other turbocharged gasoline engines. The carbon canister is located on the fuel filler neck at the right rear of the vehicle. Fuel vapors are supplied to the intake manifold at two different points depending on the engine speed. EVAP Canister Purge Regulating Valve 1 N80 is controlled by the ECM and meters the amount of fuel vapor taken in by the engine.From EVAP carbon canisterAt idling speed and at low to medium engine loads, fuel vapors are fed into the intake manifold downstream of the throttle valve because of the lower pressure in the intake system. When the engine is running under boost conditions, vapors are fed into the system upstream of the turbocharger. Two non-return valves prevent fuel vapors from returning to the carbon canister.Carbon canisterFuel vapor inlet to crankcase breather pipeInlet point with non-return valve on intake side of turbocharger To intake manifoldElectrical connectionEVAP Canister Purge Regulator Valve 1 N801Inlet into intake manifold downstream of throttle valve2Valve unit with: 1 Non-return valve for inlet into intake side of turbocharger when there is positive pressure in the intake manifold2Non-return valve for inlet into intake manifold when there is negative pressure in the intake manifold616_04313Cylinder headTechnical features• Aluminum cylinder head with twin composite camshafts. • Four valves per cylinder. • Modular-design cylinder-head cover. • Variable inlet camshaft timing on all models, adjustment range 50°, lockable in retarded position. • Variable exhaust camshaft timing, adjustment range 40°, lockable in advanced position. • Central positioning of spark-plugs (at center of valve star). • High-pressure fuel pump driven by intake camshaft (four-lobe cams). • Integral exhaust manifold. • Cross-flow cooling, see “Cylinder head cooling“ on page 24.Camshaft Position Sensor 2 G163 Camshaft Position Sensor G40 Camshaft Adjustment Valve 1 N205Modular-design cylinder-head coverThe cylinder head cover is made of die-cast aluminum and forms a single, non-separable unit with the two camshafts. This means that the four-bearing camshafts cannot be removed. To reduce friction, the first bearing of each camshaft, which is subject to the greatest loads from the belt-drive timing gear, is a deep groove ball bearing.Crankcase venting system non-return valveExhaust Camshaft Adjustment Valve 1 N318616_040Integral exhaust manifoldIn the integral exhaust manifold, the four exhaust ports are routed inside the cylinder head to a central flange. The catalytic converter is mounted directly on that flange. As well as increasing fuel efficiency and thermal advantages, this design saves approximately 4.4 lb (2.0 kg) in weight compared to a conventional exhaust manifold.616_034Key to illustration on Page 151 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 14Cylinder head cover Camshaft Adjustment Valve 1 N205 Exhaust Camshaft Adjustment Valve 1 N318 Cylinder 2 Intake Camshaft Adjuster N583* Cylinder 3 Intake Camshaft Adjuster N591* Cylinder 2 Exhaust Camshaft Adjuster N587* Cylinder 3 Exhaust Camshaft Adjuster N595* Camshaft Position Sensor G40 Camshaft Position Sensor 2 G163 Camshaft cover Deep-groove ball bearing Sliding cam sleeve* Exhaust camshaft Coolant pump drive sprocket Roller-lever cam follower with support Valve spring retainer17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Valve stem oil seal Valve collets Valve spring Camshaft bearing cap Cylinder head cover gasket (metal gasket) Cylinder head Cylinder head gasket Fuel rail Fuel Pressure Sensor G47 Fuel Injectors 1- 4 (N30 - N33) Oil Pressure Switch F1 Intake valve Intake camshaft Fuel Pressure Regulator Valve N276 High-pressure fuel pump* Not used on the North American version of this engine.Layout on 1.4l TFSI with cylinder shut-down feature1 2 3 6* 4* 5* 7* 8 9 * Not used on the North American version of this engine.101112*13143031111516 17 18 19 2920 2827 212625242223616_02115Oil supplyOil circulation systemThe oil system supplies all bearings, the piston cooling jets, the variable valve timing system, the valve gear and the turbocharger with sufficient oil for lubrication.Oil Pressure Switch F1Oil supply to turbochargerCamshaft oil galleryConnections for engine oil coolerMain oil galleryRegulated oil pumpSump top section with equipment mounting bracket Sump bottom section with Oil Level Thermal Sensor G266Oil filter on upper section of sump616_00216Regulated oil pumpCompared with other regulated oil pumps, this design is distinguished by a sophisticated control concept that enables even more efficient operation.OverviewCold start valveCoverPump driven gear (axially variable)Drive shaft with pump driving gearCompression spring of adjuster unit Control springControl pistonOil strainerPump casingIntake manifold616_003DesignIn terms of its basic design, the oil pump is a spur-gear pump. One of the pump gears is axially variable (pump driven gear). By varying the axial position of the gear, the delivery rate and pressure can be regulated in a controlled manner. Control of the oil supply for operating the regulating piston is performed by Oil Pressure Regulation Valve N428.Regulating pistonPump driving gear Delivered oilPump driven gear (axially variable) Intake from sump616_022Reference More information on the regulated oil pump can be found in eSelf-Study Program 922903 Audi 2.0L TFSI Engine with AVS.17Oil Pressure Regulation Valve N428Oil Pressure Regulation Valve N428 is responsible for supplying the oil pressure for the regulation piston of the oil pump. It is located on the rear of the cylinder block and is controlled by the ECM. During low engine speed operation, N428 is connected to ground by the ECM which switches the oil pump to its lower pressure setting. The lower pump pressure is selected according to engine load, engine speed, oil temperature and other operating parameters. In that setting, the power required to drive the oil pump is reduced, which lowers fuel consumption. During high speed operation or under high engine loads (acceleration at full power), N428 is disconnected from ground by the ECM. This switches the oil pump to its higher pressure setting. In both pressure settings, the pump delivery is varied by an adjuster unit to suit variations in the engine’s oil requirements.Oil channel in cylinder block Drive shaftAdjuster unitOil Pressure Regulation Valve N428Regulating piston To oil filter616_04618Sump1.4l TFSI engineThe oil filter is mounted to the cast aluminum sump top section. The sheet steel sump bottom section is bolted to the bottom of the upper oil sump. A diaphragm valve in the filter prevents oil from draining out when the engine is not running. Underneath the crankshaft is the oil baffle plate which separates the crankshaft drive gear from the sump.Oil baffle plateSump top sectionMount for A/C compressorOil filter cartridgeOil Level Thermal Sensor G266 Sump bottom section616_01119Oil coolingThe engine oil cooler is mounted directly on the cylinder block underneath the intake manifold. It is an oil/coolant heat exchanger and, therefore, incorporated in the engine's coolant circulation system. After passing through the engine oil cooler, the oil flows into the main oil gallery and on to other lubrication points in the engine.Coolant returnCoolant flowOil flow to cylinder headOil Pressure Switch F22Main oil galleryPiston cooling jetsMain bearingRiser pipe from oil filter to oil coolerSump top section with oil baffle plateEngine oil cooler (oil/coolant heat exchanger)Regulated oil pumpOil Level Thermal Sensor G266Oil filter cartridgeSump bottom section616_03320Cooling systemIntroductionThe system is a twin-circuit cooling system which enables different coolant temperatures to be achieved in the cylinder head and the cylinder block. In the cylinder head, the cross-flow cooling system (from intake side to exhaust side) achieves more even temperature distribution. In addition, the coolant channels in the cylinder head have been dimensioned to adequately cool the integral exhaust manifold. Mounted directly on the cylinder head is the thermostat housing and integral coolant pump. The coolant pump is driven by a toothed belt running off the exhaust camshaft.Cross-flow cooling in cylinder head with cooling of integral exhaust manifoldCoolant pump driven by exhaust camshaftTo passenger compartment heat exchangerThermostat-tocylinder-head gasketThermostatCoolant-pump-to-thermostat gasketFlow to radiatorReturn from radiator Coolant connections for oil coolerCylinder block coolant jacket open at top (open-deck design)616_02421System overview1 324 5 6 7 8 11 10 912 2 13 2 1415 17 18 19616_00516Key: 1 Coolant expansion tank 2 Non-return valve 3 Passenger compartment heat exchanger 4 Turbocharger 5 Transmission oil cooler (ATF heat exchanger) 6 Engine Coolant Temperature Sensor G62 7 Thermostat 1 8 Coolant pump 9 Thermostat 2 10 Engine oil cooler 11 Intercooler integrated in intake manifold 12 Auxiliary heater 13 Recirculation Pump V55 14 Flow restrictor 15 After-run Coolant Pump V51 16 Intercooler 17 Radiator fan V7 18 Engine Coolant Temperature Sensor on Radiator Outlet G83 19 RadiatorCooled coolant Heated coolant ATF22ThermostatThe thermostat is integrated in the thermostat housing, which is mounted directly on the cylinder head. Inside the thermostat housing there are two thermostats for the twin-circuit cooling system.Thermostat 2 for cylinder blockTo passenger compartment heat exchangerThermostat 1 Opens from approximately 188 °F (87 °C) and allows coolant to flow from the radiator to the coolant pump.Thermostat 2 Opens from approximately 217 °F (103 °C) and allows heated coolant to flow from the cylinder block to the radiator. The entire coolant circulation system is open.Return from radiator Flow to radiator From passenger compartment heat exchangerThermostat 1 for cylinder head616_047Coolant pumpThe coolant pump is integrated in the thermostat housing. The complete module is bolted onto the cylinder head. It is sealed from the coolant channels by EPDM (ethylene propylene diene monomer) rubber gaskets. One gasket sits between the coolant pump housing and the cylinder head, and the other between the coolant pump and the thermostat housing. The coolant pump is driven by a separate toothed drive belt running off the exhaust camshaft. That belt-drive system is on the flywheel end of the engine and is maintenance free. However, it does have to be replaced if the coolant pump is replaced.Coolant pump belt drive systemDrive belt coverThermostat 2 for cylinder blockThermostat housingExhaust camshaft Engine Coolant Temperature Sensor G62Coolant pump housing Coolant pump616_031NoteBefore removing and when tensioning the coolant pump drive belt, always refer to the instructions in ElsaPro.23Cylinder head coolingIn the cross-flow cylinder head, the coolant flows from the intake side around the combustion chambers to the exhaust side. There it splits into two areas, above and below the exhaust manifold. It flows through multiple channels, absorbing heat. From the cylinder head it flows into the thermostat housing where it mixes with the remaining coolant. This design has a number of advantages: • The coolant is heated by the exhaust while the engine is warming up. The engine reaches normal operating temperature more quickly. That reduces fuel consumption and the vehicle interior can be heated sooner. • Because of the smaller exhaust surface area before it reaches the catalytic converter, the exhaust loses little heat when the engine is warming up and the catalytic converter heats up to its normal operating temperature more quickly despite the cooling effect of the coolant. • When the engine is under maximum load, the coolant is cooled to a greater degree and the engine can be run fuel and emission-efficiently. That lowers fuel consumption at full power by as much as 20% compared with turbocharged engines with external exhaust manifolds. In this case the components are protected by the cooling effect with an over-rich mixture.Coolant jacket and integral exhaust manifoldTo protect the engine and especially the cylinder head against overheating, Engine Coolant Temperature Sensor G62 has been placed at the hottest point in the coolant flow, close to the exhaust manifold.Intake sideMain coolant jacketEngine Coolant Temperature Sensor G62Upper coolant chamber Lower coolant chamber Exhaust port with flange connecting to turbochargerExhaust side616_02324IntercoolerAfter the intake air has passed through the turbocharger, it is very hot. It is heated up to temperatures as high as 392 °F (200 °C)., mainly due to the compression process, but also because the turbocharger itself is very hot. As a result, the air has a lower density, and less oxygen would enter the cylinders. Cooling it to a little above ambient temperature increases its density again and more oxygen is supplied to the cylinders. Furthermore, cooling the air reduces engine tendency to knock and reduces the production of Oxides of Nitrogen (NOX). To cool the air from the turbocharger, it is passed through an intercooler, which is integrated in the intake manifold module. The intercooler is an air/coolant heat exchanger and incorporated in the engine’s coolant circulation system. The design and function of the intercooler in the intake manifold module are similar to that of a normal liquid cooler or radiator. A pipe carrying the coolant passes through a matrix of aluminum fins. The hot air flows over the fins and the heat of the air is passed to the fins. The fins transfer the heat to the coolant. The heated coolant is pumped to the intercooler system’s auxiliary radiator where it is cooled down again.Heated air in turbocharger outlet pipeTurbochargerCharge Air Pressure Sensor G31 and Intake Air Temperature Sensor 2 G299IntercoolerCooled charge airIntake manifold Heated coolant to intercooler radiator in front endCooled coolant from intercooler radiator in front end616_02525Intercooler coolant circulation systemThe coolant circulation system for the intercooler is driven by After-run Coolant Pump V51. The turbocharger is also incorporated in that "low temperature" coolant circulation system. This coolant circulation system should be seen as independent. It is only connected to the expansion tank, see “System overview“ on page 22. Isolation is by way of flow restrictors and a non-return valve. Because of that separation, temperature differences of up to 212 °F (100 °C) from the main cooling system can occur. The pump is operated by means of a PWM signal from the ECM. The pump is always run at 100%. The times at which it is switched on and off are calculated using a data map. The most important variables used are the engine load and the charge air temperature upstream and downstream of the turbocharger when the engine is running. Run-on function After the engine is switched off, after-heating effects can cause the coolant to boil under certain circumstances (if the car has been driven at top speed and/or up a long climb in high outside temperatures). After the engine is switched off, the pump therefore runs on for a certain time according to a data map stored on the engine management ECU. The data map is computed using a model which calculates the exhaust temperatures. That then serves as a measure for the turbocharger housing temperature. While the pump V51 is running, the electric radiator fan is operated at the same time.After-run Coolant Pump V51V51 is bolted onto the cylinder block below the intake manifold. Integrated in the pump is an electronic control circuit. It analyzes the PWM signal from the ECM. The pump is also fully diagnosis-compatible. Communication with the ECM for diagnostic purposes takes place via the PWM signal lead. The pump carries out a self-diagnosis routine when in operation. If a fault is detected, the details are stored on the pump's control module. The ECM continues to cyclically check that the pump is actually running. This involves connecting the control signal to ground for 0.5 seconds every 10 seconds. If any faults are detected, the details are sent to the ECM. Diagnosable faultsFault number1 2 3 4TurbochargerDescription/RemarksRunning dry 1 Pump mechanism jammed Pump overheating Minimum speed not reachedBleeder pipeIntercooler integrated in intake manifoldAfter-run Coolant Pump V51Cooled coolant Heated coolantIntercooler coolant radiator26616_050Air intake and turbocharger systemsOverviewThe air intake system is on the forward facing side of the engine. The air filter box is mounted directly on the engine. This has a favorable effect on the length of the air intake system and the preheating of the intake air. An air/coolant heat exchanger integrated in the intake manifold module cools the heated intake air.Air filter box mounted directly on engine Heated air in turbocharger outlet pipeCharge Air Pressure Sensor G31 and Intake Air Temperature Sensor 2 G299Throttle valve module J338Intake manifold module with integrated intercooler616_027Intake manifold module with integrated intercooler The intercooler is integrated in the injection-molded plastic intake manifold. The advantage of this is that the relatively small volume of air in the entire charge air tract can be quickly compressed. Very rapid pressure generation and very responsive engine performance are the results. The distance travelled by the charge air from the impeller to the intake manifold module through the plastic intake pipe (turbocharger outlet pipe) is also very short.Manifold Absolute Pressure Sensor G71 Intake Air Temperature Sensor G42Throttle Valve Control Module J338Fuel Pressure Sensor G247Intake manifold moduleIntercooler616_02627TurbochargerBecause the exhaust manifold is integrated in the cylinder head and has its own coolant jacket, it is possible to use a very lightweight mono-scroll turbocharger. Mono-scroll turbochargers have only one inlet helix which directs the exhaust to the turbine rotor. The significant advantage is their simplicity of design, which makes monoscroll turbochargers especially light and economical.Intake manifold from air filter Turbocharger outlet pipeNon-return valve for inlet from crankcase venting systemCharge Air Pressure Actuator V465WastegateConnecting flange to cylinder headWastegate actuating lever616_041Reference For more information on the design and function of Charge Air Pressure Actuator V465, refer to eSelf-Study Program 920243, The Audi 1.8l and 2.0l Third Generation EA888 Engines.28Oil supply and coolingThe turbocharger is lubricated by the engine oil circulation system. At high engine speeds, the blow-by gas from the crankcase venting system is fed back into the intake system upstream of the impeller. The connection for this is on the turbocharger. To provide for adequate cooling, the turbocharger is connected to the coolant circulation system. After-run Coolant Pump V51 pumps the coolant for both the intercooler and the turbocharger to the coolant radiator in the front end.Oil flowInlet from crankcase venting systemCoolant returnCoolant flowOil returnOil flow616_04929Notes30Fuel systemOverviewThe high pressure fuel injection system is made by Hitachi. It’s operating pressure is between a minimum of approximately 1450 psi (100 bar) when the engine is idling and 2900 psi (200 bar) when the engine is running at 6000 rpm. A pressure limiting valve is designed to open at pressure peaks of over 3335 psi (230 bar) and directs the fuel back to the intake side of the pump. This control concept is the same as found on the third generation EA888 engine series. If the power supply to N276 is cut off, no fuel is delivered to the high pressure system and the engine cuts out.High-pressure injectorsState-of-the-art, 5-jet fuel injectors are supplied with fuel by a stainless-steel fuel rail. This enables extremely precise fuel injection with up to three separate injection phases per power stroke.From the carbon canisterFrom fuel tankFuel injectorFuel Pressure Sensor G247High-pressure fuel pumpFuel rail616_05131Exhaust systemOverview1.4l TFSI engine without cylinder shut-downClose-coupled catalytic converterPre-mufflerMain muffler616_01232Catalytic converterDirectly downstream of the turbocharger, the exhaust passes through the catalytic converter. The catalytic converter is on the rear-facing side of the engine. Because the catalytic converter is mounted close to the engine, oxygen sensor control can start very quickly.Heated Oxygen Sensor G39Oxygen Sensor after Catalytic Converter G130Catalytic converter616_05733Engine management systemSensors and actuatorsSensorsTransmission Neutral Position Sensor G701Oil Pressure Switches F1, F22Knock Sensor 1 G61Accelerator Pedal Position Sensor G79 Accelerator Pedal Position Sensor 2 G185Brake Light Switch FOil Level Thermal Sensor G266Engine Speed Sensor G28 Engine Control Module J623 Charge Air Pressure Sensor G31 Intake Air Temperature Sensor 2 G299Brake Booster Pressure Sensor G294Intake Air Temperature Sensor 1 G42 Manifold Absolute Pressure Sensor G71Fuel Pressure Sensor G247Camshaft Position Sensor G40 Camshaft Position Sensor 2 G163 Throttle Valve Control Module J338 EPC Throttle Drive Angle Sensors 1 & 2 G187 & G188Engine Coolant Temperature Sensor G62 Engine Coolant Temperature Sensor on Radiator Outlet G83Heated Oxygen Sensor G39 Oxygen Sensor after Catalytic Converter G130 Charge Pressure Actuator Position Sensor G581Auxiliary signals: −− Cruise control system −− Speed signal −− Start request to ECM (keyless start 1 + 2) −− Terminal 50 −− Crash signal from Airbag Control Module34ActuatorsOil Pressure Regulation Valve N428Fuel Pressure Regulator Valve N276Continued coolant circulation pump V51Oxygen Sensor Heater Z19 Heater for Oxygen Sensor 1 after Catalytic Converter Z29 Ignition Coils 1- 4 with Output Stage N70, N127, N291, N292Coolant Fan Control Module J293 Coolant Fan V7Injector, cylinders 1 – 4 N30 – N33Camshaft Adjustment Valve 1 N205 Exhaust Camshaft Adjustment Valve 1 N318Carbon Canister Purge Regulator Valve N80EPC Throttle Drive G186Charge Pressure Actuator V465Cooling Circuit Solenoid Valve N492Fuel Pump Control Module J538 Transfer Fuel Pump G6 Fuel Gauge Sensor G Auxiliary signals: −− Transmission Control Module/engine speed −− ABS Control Module −− A/C compressor616_00735Engine speed sensor G28Engine Speed Sensor G28Engine Speed Sensor G28 is integrated with the transmission sealing flange that is bolted to the cylinder block. It scans a 60-2 reluctor ring in the crankshaft seal flange. From those signals, the ECM detects the engine speed, its direction of rotation and, in conjunction with Camshaft Position Sensor G40, the position of the crankshaft relative to the camshaft.Detection of direction of rotation When an engine is switched off, it does not immediately come to a standstill but continues turning for a couple more revolutions. If a piston is just approaching TDC on the compression stroke when the engine is switched off, it is then forced backwards by the compression pressure. At that point the engine momentarily rotates counterclockwise. That cannot be detected by a conventional engine speed sensor. Loss of signal If there is a short circuit or one or more circuit breaks, the signal from G40 is used as a substitute regardless if the engine is running or not. The maximum engine speed is limited to approximately 3000 rpm and the EPC MIL is switched on. In addition, a DTC is stored in the ECM.616_053Reluctor ringSignal utilization The signal is used to determine the computed injection timing, injection period and ignition timing. It is also used for the variable valve timing.Method of operation The two outer Hall-effect plates of the sensor simultaneously detect a rising and a falling edge on the reluctor ring. The third plate positioned off-center between the two outer plates is decisive for detecting direction of rotation.Low engine speed signal0.2 ms/div.High engine speed signal616_05836Detection of direction of rotationThe time sequence of the signals from the three Hall-effect plates when detecting a rising edge is decisive in detecting whether the engine is rotating clockwise or counterclockwise.0.2 ms/div.• Engine clockwise rotationIf the engine is rotating clockwise, the rising edge is detected by Hall-effect plate 1 first. A moment later the rising edge is detected by Hall-effect plate 3 and then Hall-effect plate 2. Because the time gap between Hall-effect plate 1 and Hall-effect plate 3 is shorter than between Hall-effect plate 3 and Hall-effect plate 2, it is evident that the engine is rotating clockwise. An electronic circuit in the sensor conditions the signal and sends a specific low width signal to the ECM.Signal width for clockwise rotation616_059• Engine counterclockwise rotationIf the engine is rotating counterclockwise, the rising edge is detected by Hall-effect plate 2 first. A moment later the rising edge is detected by Hall-effect plate 3 and then Hall-effect plate 1. As the time sequence of the signals is now reversed, the sensor detects that the engine is rotating counterclockwise. The electronic circuit in the sensor conditions the signal and sends a double low width signal to the ECM.0.2 ms/div.Signal width for anti-clockwise rotation616_06037AppendixSpecial tools and workshop equipmentT10133/19 Puller T10359/3 Adapter616_062616_063For removing the high pressure injectorsFor removing and installing engine in conjunction with engine support T10359 and engine and transmission jack V.A.G 1383 AT10478/5 Hexagon head screw M10x1, 25x45 T10479/4 Hexagon head screw M8x45T10487 Assembly tool616_064616_082For replacing shaft seal for camshaft, timing side and/or transmission sideFor pressing down toothed belt to install the camshaft locking tool T10494 in the camshaftsT10494 Camshaft locking toolT10497 Engine support616_066616_067For locking camshaft in position when checking and adjusting timingFor removing and installing engine in conjunction with engine and transmission jack V.A.G 1383 A38T10498 Removal toolT10499 Ring spanner, 30 mm616_068616_069For removing O-ring on camshaft belt pulleyFor operating toothed belt tensioning pulleyT10500 Insert tool, 13 mmT10505 Thrust piece616_070616_071For operating toothed belt tensioning pulleyFor installing O-ring on camshaft belt pulleyT10504 Camshaft locking toolT10508 Special wrench/1/2616_079616_080For locking camshaft in position when checking and adjusting timing −− With testing pin T10504/2: checking camshaft installation −− With locking pin T10504/1: adjusting camshaft installationFor removing and installing coolant pump thermostat39Self-study programsFor more information about the technology of the Audi 1.4l TFSI Engine, please refer to the following Self-Study Programs.Service Training922903 Audi 2.0L TFSI Engine with AVSeSelf-Study Program 920243920243 The Audi 1.8L and 2.0L Third Generation EA888 EnginesThe Audi 1.8L and 2.0L Third Generation EA888 EnginesThe 2.0L 4V TFSI Engine with AVS Self-Study Program 922903140Knowledge assessmentAn On-Line Knowledge Assessment (exam) is Available for this eSelf-Study Program. The Knowledge Assessment is required for Certification credit. You can find this Knowledge Assessment at: www.accessaudi.com From the accessaudi.com Homepage:• Click on the “ACADEMY” tab • Click on the “Academy site” link • Click on the Course Catalog Search and select “920253 The Audi 1.4l TFSI Engine” Please submit any questions or inquiries via the Academy CRC Online Support Form which is located under the “Support” tab or the “Contact Us” tab of the Academy CRC.Thank you for reading this eSelf-Study Program and taking the assessment.41All rights reserved. Technical specifications are subject to change without notice. Audi of America, LLC 2200 Ferdinand Porsche Drive Herndon, VA 2017142920253