TECHNICAL DOCUMENTATION
SSP 920493 – The Audi 4,0l V8 TFSI engine from the EA825 series

This PDF is currently unavailable.
Read document text
The Audi 4.0l V8 TFSI engine from the EA825 serieseSelf Study Program 920493Audi of America, LLC Service Training Created in the U.S.A. Created 2/2020 Course Number 920493 ©2020 Audi of America, LLC All rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC. Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.The eSelf-Study Program (eSSP) teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a repair manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. For further information about maintenance and repair work, always refer to the current technical literature.Release Date: February 20202IntroductionEngine description and special features Technical data 56 7Engine mechanicsCylinder block Crankshaft Cylinder head Camshaft drive configuration Crankcase ventilation system Positive Crankcase Ventilation (PCV) Fuel tank ventilation Vacuum system 88 12 18 31 36 41 42 44Oil supplyOil circuit overview Oil pump Piston cooling Sensors and actuators Oil filter and oil-coolant heat exchanger Oil filter module Oil supply in the cylinder head cover 4646 48 50 51 53 54 55Drive for ancillaries Cooling systemSystem overview Coolant circuit in cylinder block Cooling concept for the cylinder head Transmission coolant circuit 56 5858 60 62 67Air supplyOverview of air ducts Intake manifolds Throttle Valve Control Modules GX3 and GX4 6969 71 72TurbochargingTwin scroll exhaust manifold Twin scroll turbochargers Turbocharger mounting Turbocharger oil and coolant connections Heat shield in inner V of engine 7373 74 76 77 78Exhaust system Fuel systemHigh-pressure injector 79 8081Engine managementSystem overview Engine Control Module 8282 84Inspection and maintenanceService information and operations Special tools and workshop equipment 8585 86Knowledge assessment8734IntroductionThe new Audi V8 engine from the EA825 series is a joint development of Porsche and AUDI AG. The engine construction is based on the V6 engine from the EA839 series. This has advantages not only for the manufacturing process; the close relationship has benefits for after sales service as well. For example, many of the special tools can be used for both engines. The new V8 engines were first introduced by two other Group brands: Bentley and Porsche. At Audi, the new V8 will be installed first in the A8. The engines are manufactured in the new Porsche engine production facility in Zuffenhausen.676_153Learning objectives of this eSelf-Study Program: This eSelf-Study Program describes the function of the 4.0l V8 TFSI engine of the EA825 engine series. Once you have completed this eSelf-Study Program, you will be able to answer the following: › › › › › What are the technical characteristics of the engine? How do the oil supply and engine cooling systems work? What are the special features of the air supply system? What effect does the improved injection system have? What has changed for after-sales service and maintenance?5Engine description and special features› › › › › › › › › › › › › › Eight-cylinder V-engine with 90° bank angle Aluminum cylinder block Chain drive valve timing Four valves per cylinder, double overhead camshafts (DOHC), roller cam followers, variable valve timing Turbochargers with charge air cooling (maximum charge pressure: 31.9 psi [2.2 bar] absolute) Emission control system with pre and main catalytic converter system, Oxygen sensors High-pressure and low-pressure fuel systems (controlled according to demand) Cylinder on Demand (CoD) Indirect charge air cooling system Fully electronic direct injection with electric throttle Adaptive Oxygen sensor control Mapped ignition with single ignition coils Cylinder-selective adaptive knock control Thermal management system Advantages over the previous version V8 from the EA824 family: › High torque at low rpm › Improved responsiveness › Significant increase in efficiency › Increased power output and torque › Better fuel economy › Meets the relevant country-specific emission standards › Thermal management system (new cooling module) › Reduced engine friction › Improved injection systemHighlights of the new V8 engineCrankcase (optimized for weight) with APS-coated cylinder running surfaceThermal managementFriction-optimized valve gearFuel system with central injector configurationCylinder head design with valve lift and Cylinder on Demand“Hot Side Inside” (HSI) turbocharging system676_0026Technical dataTorque-power curve of 4.0l V8 FSI engine (engine code CXYA)486.79 lb ft (660 Nm) at 1850 - 4500 453.26 hp (338 kW) at 5500Diagram: engine at full load Power output in kW Torque in Nm676_003Features Engine code Design Capacity Stroke Bore Cylinder spacing Number of valves per cylinder Firing order Compression ratio Power output at rpm Torque at rpm Fuel Turbocharging Engine management Engine weight Emission control Emission standard Firing order during changeover to 4 cylinder operation (cyl. 2, 3, 5, 8 shut off)Specifications CXYA 8-cylinder engine with 90° V angle 243.85 cu in (3996 cm)3 3.38 in (86.0 mm) 3.38 in (86.0 mm) 3.22 in (82.0 mm) 4 1-3-7-2-6-5-4-8 11.0 : 1 453.26 hp (338 kW) at 5500 486.79 lb ft (660 Nm) at 1850 - 4500 Premium unleaded “Hot Side Inside” (HSI) turbochargers with charge air cooling (maximum charge pressure: 31.9 psi [2.2 bar] absolute) Bosch MG1CS008 509.2 lb (231 kg) Dual exhaust system with pre-catalytic converter and 3-way catalytic converter ULEV125, (Pr. number:7MU) 1-7-6-47Engine mechanicsCylinder blockThe aluminum (ALSi9Cu3) cylinder block is single sand cast unit. It is a “deep skirt” design. This means the individual cylinder walls reach down as far as the upper oil sump providing a very high degree of rigidity. The entire cylinder block including the bearing covers and corresponding bolts weighs 86.2 lb (39.1 kg).In addition to the oil and cooling passages, the following components and assemblies are integrated with or installed on the cylinder block:› › › › › › › Oil spray jets Water pump intermediate shaft Oil pump Oil cooler Coolant pump Engine mounting Mounting points for ancillary componentsThe engine number is engraved on a plate on the front of the engine below cylinder bank 1. There is also a sticker with the engine code and serial number attached to the vacuum pump cover.676_0048Atmospheric plasma spraying (APS)To create a sufficiently robust iron running surface, the cylinder walls are first roughened with a special milling tool which cuts a dovetailed pattern into the cylinder. The resulting undercuts ensure that the APS coating adheres properly. A rotating plasma torch is then inserted into the cylinder. An arc discharge is used to create a plasma into which a powdered coating material is blown using compressed air. The powder melts and is sprayed onto the rough cylinder wall. There it solidifies and fills the undercuts thus creating a wear layer. A layer of iron (roughly equivalent to 100Cr6 bearing steel) is applied in several layers in approximately 30 seconds. The final thickness is approximately 150 micrometers. (One micrometer equals one millionth of a meter.)Application of plasma coating676_005Wear layer on cylinder wallCylinder block676_0069Crankshaft bearingsThe upper crankshaft bearing bosses are integral with the cylinder block. The grey cast iron bearing caps are retained with longitudinal and transverse bolts.Grey cast iron bearing capCrankshaft bearing shell (bottom)Crankshaft bearing shell (top)Hole for locking pin T40069 (with engine removed)Transverse bolt for cross-bolting the crankshaft bearing caps.676_00710Sump (top section)The top section of the sump is made of an aluminum die cast alloy. Dowel pins are used to ensure exact positioning during assembly.Timing chain coverThis die-cast component is made of an aluminum alloy; if it needs to be removed, it can be pressed off the cylinder block using auxiliary bolts. The engine speed sensor as well as the crankshaft oil seal are located in the cover.Sump (bottom section)The bottom section of the sump is made of an aluminum sheet metal. The oil drain plug and the oil level/oil temperature sensor are integrated with it.Sealing flange (pully end)This component is also made of an aluminum alloy. It provides the attachment point for the dipstick tube and the crankshaft oil seal.Cylinder 1Oil seal Oil ringTiming chain coverSealing flange Pulley endEngine number Oil baffle plateOil pan top sectionOil pan bottom sectionOil drain plugOil Level Thermal Sensor G266676_008NoteHousing cover and sumps are sealed by a liquid gasket (see ElsaPro for details).11CrankshaftThe forged steel crankshaft is supported by five main bearings to ensure a smooth running engine. The cylinder banks are positioned at a 90 degree angle to one another with connecting rods of the cylinders opposite of each other sharing the same bearing journal.676_00912Crankshaft bearingsThe IROX bearings conform to the high demands of hybrid drive and start/stop operation. Three-layer bearing construction:› The steel backbone provides the required stability. › The second layer is made of a soft metal carrier substrate to which the third layer is fixed. › The third layer consists of a polymer base with a homogeneous distribution of filler materials which ensure the best possible running and wear characteristics.Crankshaft bearing shell (top)Timing gear (drive gear) Crankshaft bearing 1 (pulley end) Chain sprocket (drive gear for oil pump)Crankshaft bearing shell (bottom)676_01013Thrust washersFour thrust washers (top and bottom) are installed on crankshaft bearing four to control longitudinal movement of the crankshaft. The oil grooves of the thrust washers face towards the crankshaft.Crankshaft bearing four Thrust washer (bottom)Thrust washer (top) Crankshaft bearing shell (top)676_01314PistonTo minimize noise, the cast pistons are mounted at a 0.5 mm offset towards the pressure side (see illustration 676_016 below). Due to the compression and valve timing, intake valve recesses of different sizes are integrated in the piston crown (intake valve: large; exhaust valve: small). The chamber walls on the piston pressure side are narrower than on the counter-pressure side which is subject to less strain. The high rigidity of the pressure side makes it possible to achieve a defined piston wear pattern while optimizing the load. On the counter-pressure side, the piston is much softer and can adapt better to the shape of the cylinder. This combination results in different pistons for cylinder bank 1 (right bank) and cylinder bank 2 (left bank).Piston rings1. Top piston ring (compression ring) mounted in the ring carrier, rectangular section seal 2. Taper-faced ring 3. Oil scraper ring (3 parts)Piston pinsThe steel alloy piston pins are coated and hardened. Each piston pin measures 22 mm in diameter.NoteThe small valve recesses always face the inner V.676_014Piston pressure side Counter-pressure sideCounter-pressure side Piston pressure side676_01615Connecting rodsThe cracked trapezoidal connecting rods are made of high-strength steel. The bushing in the upper connecting rod small end is made from a copper alloy (CuNi9Sn6). The connecting rod bearings are 22.3 mm wide. Both bearing shells are identical. The bearings are made of three materials: a steel substrate, a bismuth-bronze alloy intermediate layer and a thin bismuth crystal lining. The connecting rods are installed at an offset to the engine’s longitudinal axis.676_017Installing the connecting rodsIt is important to install the connecting rods in the correct position. The points of the two installation markings must be in line with one another (see illustration 676_018 ). Only connecting rods of the same weight class may be installed on a given engine.Installation markingView showing data matrix code XX = weight class of large connecting rod eye YY = weight class of small connecting rod eye676_018 676_019NoteDo not interchange bearing shells during installation; if new components are installed the specifications for clearance tolerances must be observed (see Elsa Pro for details).16Belt pulley / vibration damperA single bolt secures the pulley/vibration damper to the crankshaft, and a dowel pin locates them in the correct position. A diamond-coated washer is installed between the vibration damper and the end of the crankshaft as a locating element. The housing of the viscous vibration damper is made of forged steel, while the inertia ring is manufactured out of aluminum. This provides the greatest possible strength against deformation caused by centrifugal force.Diamond-coated friction washerPulleyCrankshaft speed detection676_020Engine Speed Sensor G28 is located in the timing chain cover. It detects signals from the magnetic ring on the drive plate.Magnetic ring Carrier plateEngine Speed Sensor G28676_021 17Cylinder headThe cylinder heads have the following technical features:› › › › › › › › DOHC, 4 valves per cylinder. Roller cam followers. Integral exhaust manifold. “Hot Side Inside” (HSI). Direct injection combustion process with central injector position. Audi valvelift system (AVS). Enables Cylinder on Demand (CoD) operation. Intake valves: hardened and tempered. Exhaust valves: hardened and tempered, sodium-filled hollow stems.676_02318Noise insulationThe two-part insulating mats over the cylinder head covers help reduce noise. This provides effective insulation against high-frequency ticking noises greater than 2500 Hz from the injectors and the high-pressure fuel pumps.676_044NotePay close attention to the installation order of components on the cylinder heads. Some components may be located under the insulating mats and can no longer be installed after the mats have been installed.19Cylinder head cover attachmentsCamshaft adjusterIgnition coilsHall senderCylinder head cover (right-side)Camshaft control valves (solenoid)676 _045Timing chain case coverCylinder head gasketA three-layer metal gasket is used. It is only available in one thickness.Cylinder head gasket676 _024 20Valve gear110 9 28 376 4 5676 _025Legend1. 2. 3. 4. Roller cam followers with supporting element Exhaust valve spring Twin-lip valve stem oil seal Exhaust valve Bi-metal valve with sodium filling and chromium-plated valve stem ends 5. Inlet valve Monometallic valves with inductive hardened valve seats 6. Valve spring plate (bottom) 7. Single-lip valve stem oil seal 8. Inlet valve spring 9. Upper valve spring plate 10. Valve keepersThe valve springs are a simple cylindrical shape.21Camshaft housingsThe camshaft housings of both cylinder banks work in the same way; the only difference is the location of certain components. The camshaft housing for cylinder bank 2 is described here as an example. The cylinder head is sealed by a liquid gasket and a rubber molded gasket. The camshafts are mounted in five sleeve bearings in the camshaft housing. The center bearing is constructed additionally as an axial bearing. The ignition coils, cam actuators for Cylinder on Demand, Hall sensors for camshaft position detection, high pressure fuel pump, injectors, fuel rail and oil separator for the crankcase breather system are also installed.12111 102 3 4 75 689676_026Legend1. Cylinder head cover 2. Retention valve 3. Dowel sleeves 4. Seal 5. Camshafts 6. Control valve for camshaft adjuster 7. Axial bearing 8. Bearing cap 9. Bolted connection for camshaft bearing 10. Sealing plug 11. Plug 12. Bolted connection for cylinder head cover22Identification number of matched pair for camshaft housing and camshaft bearingThe following applies to the bearing caps: E for intake side and A for exhaust side; bearing position number 1 to 5 starting at the front.676_027Identification number of matched pair for camshaft housing and cylinder headThe following applies to the camshaft bearing caps: E for inlet side and A for exhaust side; bearing position number 1 to 5 starting at the front. The identification number for the matched pair is given underneath. The three-digit numbers on the bearing caps (see marking) must match the last three digits of the four-digit number on the camshaft housing.› This identification number matches each bearing cap to a specific cylinder head. › It is important to ensure correct allocation during assembly. › The two four-digit numbers must be the same: XXXX = XXXX.Camshaft housingCylinder head676_02923CamshaftsAll four camshafts are composite camshafts comprising a basic shaft with pressed-on end pieces. The cam elements are installed onto the splines on the shaft. Two cam elements are fixed in position; the other two are moveable. The moveable cam elements have two cam profiles for each valve. This provides the operational basis for the Cylinder on Demand (CoD) system. The high-pressure fuel pumps are driven by the exhaust camshafts via four-lobe cams. In addition, each camshaft has a sender wheel used for detecting the camshaft position. The bearings for the camshafts are located in the basic shaft. A groove for the axial bearing is located in the center of the camshaft.676_03024Camshaft components87 176 25 3 4676_031Legend1. 2. 3. 4. 5. 6. 7. 8. Basic shaft Bearing caps Ball-and-spring locking mechanism Control valve for camshaft adjuster Shaft stub with four-lobe cams for driving the high-pressure fuel pump Cam elements, moveable for the Cylinder on Demand system Cam elements Sender wheel25Cylinder on Demand (CoD)The EA825 engine is equipped with a cylinder management system. This system allows two cylinders on each cylinder bank to be shut off in certain circumstances, for example, under low engine load. When these cylinders are shut off, the other cylinders can work more effectively with reduced throttle loss. This saves fuel and reduces exhaust emissions. The cylinders are shut off by keeping the corresponding inlet and exhaust valves closed, and by eliminating the fuel supply and ignition for these cylinders. The inlet and exhaust valves are shut off via the Audi valvelift system. To make this happen, the system’s actuators are activated in the same sequence as the firing order, which sets the moveable cam elements for cylinder 2, 3, 5 and 8 to zero stroke.› Firing order with all cylinders activated: 1-3-7-2-6-5-4-8 › Firing order with half of cylinders activated: 1-7-6-4For the vehicle occupants, it will be nearly imperceptible that only half of the cylinders are activated, as the active engine mountings eliminate nearly all potential vibrations. The function of the active engine mountings is described in SSP 920223 and SSP 990293Cylinder 15/61/23/47/8Cylinder 2676_032Legend1. 2. 3. 4. 5. 6. 7. 8. Cylinder 2 Exhaust Cam Actuator 1 F454 Cylinder 2 Intake Cam Actuator 1 F452 Cylinder 3 Exhaust Cam Actuator 1 F458 Cylinder 3 Intake Cam Actuator 1 F456 Cylinder 5 Exhaust Cam Actuator 1 F466 Cylinder 5 Intake Cam Actuator 1 F464 Cylinder 8 Exhaust Cam Actuator 1 F478 Cylinder 8 Intake Cam Actuator 1 F47626Cylinder on Demand strategyCriteria for starting/ending CoD operationEngine coolant temperature Engine torque Gear Inactive in gears Battery voltage Catalytic converter heating Engine flaps Prevented during OBD diagnosis95°F - 185°F (35°C - 85°C) Between 62.69 - 162.26 lb ft (85 - 220 Nm) depending on the engine speed D 1…3 Greater than 9,6 V Inactive Inactive › Oxygen sensor check › Catalytic converter check › Fuel tank breather check Inactive 300 sEVAP system, high load greater than 12 Maximum time in CoD cycleExhaust gas is captured and sealed in when the cylinders are shut off.How the CoD system worksThis section describes the three phases in which the sliding cams move from zero to full lift.Phase 1When the cam actuator is activated by the engine control module, the actuator pin is inserted into the Y-shaped slotted gate. The ball locks the cam element in place through spring force. The intake and exhaust valves are closed.676_03327Phase 2When the camshaft rotates further, the shape of the slotted gate causes the actuator pin to press the cam element out of the retainer.676_034Phase 3Once it has changed positions, the cam element is locked in the second position by the ball through spring force. The retraction slot pushes the actuator pin back in. This triggers the retraction signal in the actuator. The intake and exhaust valves are still closed; they are just about to be opened by the contour of the full lift cam.676_03528Camshaft adjustersTo optimize power output and torque as well as reducing emission levels and increasing fuel economy, camshaft adjusters are installed on all camshafts. The system also uses an internal exhaust gas recirculation strategy. The hydraulic camshaft adjusters are in constant operation and have an adjustment range of 50° (crank angle).Diamond-coated friction washer, must not be reusedCamshaft adjuster valve (solenoid valve, bolted into chain case cover)Intake camshaft Cylinder bank 2Timing valve (also secures camshaft adjuster to camshaft)ReferenceFor more information about the camshaft adjuster valve and the control valve, please refer to eSelf-Study Program 920173, The Audi 3.0L V6 TFSI EA839 Engine.29Intake camshaft adjustersWhen the engine is switched off, locking pins use spring force to lock the intake camshaft adjusters in the “retard” position.Adjustment range 25° cam angleChain sprocket (rotor)Stator Locking pinDirection of camshaft rotation676_036Exhaust camshaft adjustersWhen the engine is switched off, spring force on the locking pins locks the exhaust camshaft adjusters in the “advanced” position. A return spring is necessary to achieve the “advanced” locking position when switching off the engine.Chain sprocket (rotor)Return springLocking pin Stator30676_144Camshaft drive configurationThe camshaft drive system of the new V8 engine is located on the transmission side of the engine. A gear on the crankshaft drives the intermediate gear which in turn drives the simplex chains for the camshafts. The intermediate gear is configured as a tensioning gear. It is responsible for preventing noise.Camshaft Position Sensor 4 G301Camshaft Position Sensor 3 G300 Contact surface Tensioning railCamshaft Position Sensor 2 G163Contact surfaceCamshaft Adjustment Valve 2 N208 Exhaust Camshaft Adjustment Valve 2 N319 Tensioning railExhaust Camshaft Adjustment Valve 1 N318Camshaft Position Sensor G40Camshaft Adjustment Valve 1 N205Guide rail676_03931Basic positions for crankshaft/camshaft timingThe engine is in its basic position when cylinder 1 is at TDC position and the crankshaft can be locked in place. The markings on the camshaft adjusters must be opposite the corresponding projections on the camshaft housing. The camshaft adjusters must be positioned precisely, as the drive chain sprockets are tri-oval shaped. These tri-oval chain sprockets make it possible to minimize the dynamic forces from the valve gear and allow the engine to run more smoothly.Marks for basic setting676_04032Locking the crankshaftThe crankshaft can be locked in two ways, as described below. With the engine installed in the vehicle using lock in pin T10492676_041Locking pin T10492With the engine removed using lock in pin T40069Engine bracketLocking pin T40069676_04233Water pump drive shaftThe water pump drive shaft is mounted in sleeve bearings and is driven by a tensioning gear via the crankshaft.676_04334Tensioning gearThe tensioning gear must be pre-tensioned during installation using Locking Pin T40362.Coolant pump drive shaftTensioning gearCoolant pump drive gear676_01535Crankcase ventilation systemThe crankcase is vented above the cylinder head covers. An oil separator module is bolted onto each cylinder head cover for this purpose. The filtered blow-by gases are also channeled separately for each cylinder bank. The inlet points are located upstream of the intake side of the turbocharger turbines (discharge at full load) as well as in the intake manifold of the cylinder heads (discharge at partial load). Intake is regulated by non-return valves which open or close independently depending on the pressure level in the air supply. A non-return valve is installed in the breather line from the oil separator to the connection in front of the turbocharger turbines. The second non-return valve is installed in the corresponding oil separator module.Non-return valveOil seperator, bank 2Non-return valve Oil seperator, bank 1Breather line, full loadBreather line, partial loadBreather line, partial loadBreather line, full load676_046The ECM regulates the crankcase ventilation system. The system must be capable of discharging approximately 3.53 cu ft (100 L) of blow-by gases from the crankcase without loosing oil in the process.676_04736Blow-by discharge at partial loadOn both cylinder banks, the filtered blow-by gases flow from the oil separator into the corresponding intake manifold. At low air temperatures and high flow speeds, the blow-by mass flow is heated in the intake manifold to prevent it from freezing under extreme conditions. A PTC heater element is installed at the connection between the breather line and the intake manifold. It is controlled by the ECM via a PWM signal based on a calculated characteristic map.› Positive Crankcase Ventilation Heating Element N79 cylinder bank 1 (right-side) › Crankcase Ventilation Thermal Resistor 2 cylinder bank 2 (left-side)Heater element for crankcase ventilationN483 N79676_04837Oil separatorThe blow-by gases flow out of the crankcase and into the cylinder head area via channels in the crankcase. From there, the blow-by enters an inlet plenum chamber in the cylinder head cover; this is where the oil separator is installed. When the engine is running, oil that has been separated collects in the collection chamber of the oil separator.Pressure regulating valve .23 psi (85 mbar)Connection for turbochargerConnection for intake manifold Non-return valve Opens in partial-load operationOil separator (impactor)Non-return valve Opens in full-load operation Blow-by inlet Oil return channel676_049When the engine is not running or when a defined level in the oil separator is exceeded, the gravity valve opens and the oil drains into the crankcase. The gravity valve also prevents oil from the sump from entering the oil separator in the event of large fluctuations in pressure, for example due to sudden load change.Oil return valve (gravity valve)676_050ReferenceFor more information about the oil separator, please refer to eSelf-Study Program 920173, The Audi 3.0L V6 TFSI EA839 Engine.38Oil returnThe separated oil in the oil separator collects in the cylinder head cover tray (located below the oil separator). It is directed through a drilled channel down to the inlet side and then enters the valve chamber of the cylinder head via the oil discharge valve.Oil discharge valve676_05139Engine breather passages (inside)Oil return channels (outside) cylinder heads over crankcase in sump676_052The oil flows into the sump via separate return channels. The inlet point is located below the oil surface level.Oil return channels (outside) cylinder heads over crankcase in sump676_123 40Positive Crankcase Ventilation (PCV)Positive crankcase ventilation (PCV) takes place when charge pressure is present. The air flow which is channeled into the crankcase in this process is limited by defining the cross-section of the pipe in the crankcase connection. In certain operating modes, for example, to avoid blow-by gases when mixture adaption is active, Crankcase Ventilation Valve N546 is actuated, which regulates the flow of fresh air. The fresh air intake point for the crankcase is located in front of the throttle valve for cylinder bank 2. Air is drawn into the crankcase at a connection just above the upper sump on the left side of the engine. Two non-return valves are installed for security. They close when the difference in pressure between the air system and the crankcase becomes too great; otherwise the vacuum pressure inside the crankcase could become too high. The non-return valves are located in N546 and in the connection on the crankcase.Fresh air intakeCrankcase Ventilation Valve N546 Fresh air extraction before throttle valve676_053Crankcase connectionCrankcase Ventilation Valve N546Crankcase connection with non-return valve and throttle function676_125676_12641Fuel tank ventilationFuel tank ventilation is controlled by Engine Control Module J623. It is done by regulating the vapor flow from the charcoal canister via EVAP Canister Purge Regulator Valve 1 N80 and EVAP Canister Purge Regulator Valve 2 N115.When there is a vacuum in the intake manifold, the activated charcoal filter is vented via the non-return valves in the intake manifold. When there is charge pressure, venting takes place on the intake side in front of the turbocharger.Tank Ventilation Pressure Sensor 1 G952676_054From activated charcoal filterEVAP Canister Purge Regulator Valve 1 N80EVAP Canister Purge Regulator Valve 2 N115 Discharge to intake side of turbocharger at full load with assistance from suction-jet pumps Tank Ventilation Pressure Sensor 2 G951Connection to intake manifold for cylinder bank 1 with non-return valve at partial loadConnection to intake manifold for cylinder bank 2 with non-return valve at partial load676_127Tank Ventilation Pressure Sensors 1 and 2 are mounted upstream of the EVAP Purge Regulator Valves. They are used to check whether sufficient vacuum is present in the fuel tank ventilation lines.42If a ventilation line is disconnected or leaky, a pressure drop would not be measurable and the MIL would be switched on.Suction-jet pumps for fuel tank breather systemDuring times when no vacuum is present in the intake manifold, the fuel tank ventilation system discharges into the turbocharger compressor housings. This is assisted by suction-jets operating on the Venturi principle. The suction-jets utilize the pressure gradient between the pressure and the intake sides of the compressor. The accelerated air flow produces a vacuum which is used to ventilate the charcoal canister.676_056Each suction-jet pump is connected to the intake side (vacuum) and the pressure side of the turbocharger. Once there is a sufficient difference in pressure between the intake side and the pressure side, for example, at full load, a “Venturi effect” is created. This extracts the fuel vapors from the activated charcoal filter and directs them into the intake side of the turbocharger.Pressure differentialIntake side TurbochargerVenturi nozzleNon-return valve from activated charcoal filterPressure side Turbocharger676_05543Vacuum systemVacuum pressure is created by a single-vane pump driven by the inlet camshaft for cylinder bank 2. The vacuum pump must supply the following components with vacuum pressure:› The mechanical coolant pump: to ensure standing coolant in the cylinder block when the engine is warming up. › The vacuum units of the turbocharger: to close the bypass flaps thus regulating the charge pressure. › The brake servo.676_057Charge Air Pressure Actuators V465 and V546 are electro-pneumatic exhaust gas recirculation valves. They are able to initiate a calculated vacuum pressure (characteristic curve) according to the actuation (PWM) by the ECM. This determines the degree to which the bypass flaps are open; they are open when not actuated. Mechanical Coolant Pump Switch Valve N649 is an electric changeover valve. It can only be switched to “on” and “off”.44Connection for vacuum unit/ turbocharger Pressure equalization hose to prevent turbocharger pumpingDirection of flowNon-return valveConnection for mechanical coolant Charge Air Pressure pump Actuator V465 Connection for brake servo Mechanical Coolant Pump Switch Valve N649 Connection for vacuum reservoirShaft driven engine coolant pumpOutlet (vacuum pressure input)Oil Pressure Sensor G10Vacuum pump Open when actuated; otherwise closedCharge Air Pressure Actuator 2 V546Always openOpen when not actuated; closed when actuated180 cm3 single-vane vacuum-pump with axial elastomer sealA sinterred plastic air filter is installed because the breather connection is within reach of water spray (cannot be replaced separately)676_058Pressure equalization between the vacuum units of the bypass flapsIf there are differences between the characteristic curves of the two charge pressure positioners, this could cause the vacuum units to be actuated differently and create different pressure levels in the turbochargers, leading to undesired noises (turbocharger pumping). A connecting pipe equalizes the pressure between the vacuum connections of the vacuum units of both turbochargers.45Oil supplyThe key objectives for the oil circuit development are to keep pressure losses to a minimum and ensure optimal flow. Key technical features of the oil circuit are:› Fully variable map-controlled vane cell oil pump. › Piston cooling jets which inject directly into the piston crown cooling ducts. › Thermostat controlled engine oil cooler.Oil circuit overview676_059Key: A B C D Cylinder head 1 Cylinder block Cylinder head 2 Cylinder head gallery 14 15 16 17 18 19 20 21 22 23 24 25 26 Intermediate shaft bearing Oil gallery for piston cooling jets Oil Pressure Switch F22 Oil Temperature Sensor G8 Piston Cooling Nozzle Control Valve N522 Chain tensioner Camshaft adjuster Camshaft control valves Camshaft bearings Vacuum pump High-pressure fuel pump Hydraulic valve clearance compensation element Oil drain valve1 Oil pan 2 Oil Level Thermal Sensor G266 3 Oil intake with strainer 4 Oil pump 5 Oil-coolant heat exchanger (engine oil cooler) 6 Oil filter 7 Turbocharger 8 Bypass valve 9 Turbocharger non-return valve 10 Connecting rod 11 Pressure relief valve (cold start valve) 12 Oil Pressure Regulation Valve N428 13 Oil Pressure Sensor G1046Overview of engine componentsOil heat exchangerOil filter moduleOil supply gallery for components in the cylinder headMain oil gallery for crankshaft bearing lubricationSupply gallery to oil/coolant heat exchangerControl gallery to oil pumpOil pump676_06047Oil pumpDriveThe vane cell oil pump is driven by the crankshaft via a chain drive on the front side of the engine. A 7mm chain and leaf-spring chain tensioner (no hydraulic damping) is used. A guide rail is installed on the driving side of the pump due to the distance between the shafts for the chain sprockets.Oil Pressure Regulation Valve N428Coolant pump driveLeaf spring Chain tensioner Crankshaft chain sprocket, 31 teeth Oil pump Chain sprocket, 32 teeth Chain sprocket shield to reduce splash lossGuide railSuction pipe with integrated oil strainer (perforated plate) to ensure oil supply during dynamic driving676_06148Oil pumpThe fully variable vane pump has a very compact construction. It is bolted onto the crankcase. A metal gasket is necessary to seal the individual oil passages from one another at the point where the components mate.Return shut-off valvePressure relief valveRotary slide valveImpeller676_062676_065Oil pump: range of operationOil temperature in main gallery: 86 °F (30 °C) Oil temperature in main gallery: 212 °F (100 °C)676_063NoteFor new vehicles, two-stage oil pressure regulation is only activated after the first 620 mi (1000 km). This compensates for the higher friction when breaking in new parts and is the best way of removing particles of residue worn off during the break-in process. After installing new components such as the engine/short block, cylinder head, camshaft housing or turbocharger, activate the “engine run-in” program in the Guided Fault Finding (GFF). This will ensure that only the high pressure stage is allowed for the next 620 mi (1000 km).ReferenceFor further information regarding fully variable oil regulation, please refer to eSelf-Study Program 920173, The Audi 3.0L V6 TFSI EA839 Engine.49Piston coolingIt is not necessary to cool the pistons with oil spray during every phase of engine operation. When no cooling is required, Piston Cooling Nozzle Control Valve N522 is switched to ground by Engine Control Module J623. This closes off the channel from the main oil gallery to the oil gallery for the piston cooling jets. When the oil gallery is closed, the oil pressure dissipates via the piston cooling jets. Feedback to the ECM is provided by the signal from Oil Pressure Switch F22. F22 is located in the oil gallery and opens at pressures between 4.35 8.70 psi (0.3 - 0.6 bar).Piston cooling jets676_066Piston cooling jets: range of operationPiston cooling is activated based on a characteristic map that considers the variables of engine rpm, engine torque and oil temperature. For this purpose, Oil Temperature Sensor G8 provides the engine oil temperature value of the main oil gallery. Piston cooling is only activated at oil temperatures above 50 °F (10 °C).676_067 50Sensors and actuatorsOil heat exchanger Oil Pressure Switch F22Oil filter module Plastic oil filter module with pressure relief valve in cover assembly. Connection of turbocharger oil supply with integrated non-return valve. Fully synthetic filter paperPiston Cooling Nozzle Control Valve N522 Oil Temperature Sensor G8Oil Pressure Sensor G10Oil Level Thermal Sensor G266Oil Pressure Regulation Valve N428676_068NoteOil Temperature Sensor G8, Oil Pressure Switch F22 and Piston Cooling Nozzle Control Valve N522 are located under a heat shield.Oil Temperature Sensor G8G8 is also located in the inner V of the engine. This NTC thermistor measures the temperature of the engine oil in the main oil gallery. The ECM uses the signal primarily as the input variable for calculating the oil pressure regulation. In addition, the oil temperature in the main oil gallery determines whether the piston cooling jets are activated. For example, at oil temperatures over 248 °F (120 °C), the piston cooling jets are activated even at low engine speeds.676_15451Oil Level Thermal Sensor G266The signal from G266 is evaluated by the ECM, which uses the temperature and oil level values to compute the oil change interval. The information regarding oil level and oil temperature is transmitted to the ECM via a PWM signal. The sensor has a 12 Volt power supply.676_069Piston Cooling Nozzle Control Valve N522This solenoid valve operates on 12 Volt power. To activate the solenoid valve and close the oil passage for the piston cooling jets, the ECM switches it to ground. This means that the valve would be open in the event that it should fail (failsafe design).676_07052Oil filter and oil-coolant heat exchangerThe engine oil circulated by the oil pump flows first through the oil heat exchanger, which is installed in the inner V of the engine and connected to the coolant circuit on the coolant side. When the oil exits the oil-coolant heat exchanger, it flows through a passage in the cylinder block and into the oil filter module. Once it has been filtered, the oil flows into the main oil gallery of the engine; from there, it reaches the appropriate components via corresponding passages.676_071The oil-coolant heat exchanger is designed to provide a high degree of heat transfer. It comprises 19 stacked plates with plates for turbulent flow (10 oil/9 water), which provides a high degree of heat transfer. The coolant circulates via counterflow with a flow rate of up to 63.40 qt (60l) per minute.Coolant outletCoolant inletEngine oil inlet Cross-flow of engine oil and coolant through exchanger676_073Engine oil outlet676_072 53Oil filter moduleThe oil filter module is made of plastic and is installed in front of the oil-coolant heat exchanger in the inner V of the engine. This makes it very easy to replace the oil filter. A stainless steel heat shield protects the oil filter module by reflecting the heat that radiates from the turbocharger on cylinder bank 2. A bypass valve is installed in the housing cover which directs the oil past the oil filter should it become clogged. Two additional valves are installed in the oil filter housing. The non-return valve prevents oil from flowing from the turbochargers back into the sump. The oil drain valve opens when the oil filter cover is unscrewed so that the oil drains into the sump when the oil filter is exchanged.Oil filter moduleCover seal Bypass valveOil filterOil filter housingOil drain valveNon-return valveHeat shieldSeal676_07454Oil supply in the cylinder head coverThe main oil gallery in the cylinder block supplies the oil pressure to the cylinder head cover. From the main oil gallery, oil is supplied to the camshaft bearings, the hydraulic compensation elements, the high-pressure fuel pump and (on cylinder bank 2) the vacuum pump via branch ports. Oil is supplied to the large camshaft bearings and the camshaft adjusters via the main oil gallery of the cylinder head covers.Vacuum pumpMain oil gallery, cylinder head coverHigh-pressure fuel pumpHydraulic compensation elements Pressure oil from main oil galleryCamshaft adjuster676_07555Drive for ancillariesThe alternator and air conditioner compressor are each driven by a separate drive belt. Both belt drives are driven by the vibration damper of the crankshaft. The belt drives are tensioned by automatic tensioning devices and are maintenance-free.Vibration damper Tensioning roller (top) Starter-alternator Tensioner for poly V-belt Air conditioner compressor676_076Tensioning roller (bottom)Vibration damperIdler rollerPoly V-belt tensioner for starter-alternator (belt tensioner/damper)Poly V-belt tensioner for air conditioner compressor (belt tensioner/damper)676_077676_0795657Cooling systemSystem overviewThe new V8 engine has a thermal management system which activates various partial cooling circuits as required to help the engine, vehicle heating and transmission warm up quickly. In addition to providing greater convenience, the main objective is to reduce fuel consumption and exhaust emissions.676_08058Key: 1. Expansion tank 2. Heat exchanger for heater (front) 3. Heat exchanger for heater (rear) 4. Restrictor 5. High Temperature Circuit Coolant Pump V467 6. ATF cooler 7. Turbocharger, bank 1 (right-side) 8. Turbocharger, bank 2 (left-side) 9. Engine oil cooler 10. Transmission Fluid Cooling Valve N509 (actuated by Transmission Control Module J217) 11. Transmission Coolant Valve N488 (actuated by ECM J623) 12. After-Run Coolant Pump V51 13. Starter-alternator 14. Cylinder head (right-side) 15. Cylinder block (right-side) 16. Cylinder block (left-side) 17. Cylinder head (left-side) 18. Engine Temperature Sensor G407 19. Coolant pump (mechanical) With cover (standing coolant), actuated by Mechanical Coolant Pump Switch Valve N469 20. Map Controlled Engine Cooling Thermostat F265 21. Non-return valve 22. Radiator 23. Engine Coolant Temperature Sensor on Radiator Outlet G83 24. Restrictor 25. Coolant Recirculation Pump V50 26. Non-return valveCooled coolant Warm coolantThermal managementThe thermal management system is responsible for coordinating the optimal process of warming up the engine, transmission and pas senger compartment. Reducing vehicle emissions is a primary concern in this process. During the engine warm-up phase, the engine’s mechanical coolant pump and Coolant Recirculation Pump V50, After-Run Coolant Pump V51 and High Temperature Circuit Coolant Pump V467 are switched off. Transmission Fluid Cooling Valve N509 and Transmission Coolant Valve N488 are closed. All the components listed are actuated as needed (as calculated by the characteristic map) so that the required coolant flow is achieved. To provide a calculation, the characteristic map in the ECM requires numerous input parameters:› Engine coolant temperature › Ambient air temperature › Engine speed, engine torque, engine power output › Engine oil temperature › Road speed › Heating requirements › Driving mode › Radiator outlet temperature › Transmission oil temperatureThe following components can be activated in response:› Mechanical Coolant Pump Switch Valve N649 › Map Controlled Engine Cooling Thermostat F265 › Coolant Recirculation Pump V50, After-Run Coolant Pump V51 and High Temperature Circuit Coolant Pump V467 › Transmission Fluid Cooling Valve N509 and Transmission Coolant Valve N48859Coolant circuit in cylinder blockConnecting pipeDistribution pipe (hot) for ancillaries, turbocharges, oil-coolant heat changer Return flow for oil cooler Coolant return (hot) from ancillaries directly to coolant pump Coolant return (hot) to radiator via thermostat and coolant pump Supply flow for oil-coolant heat exchanger Connecting pipe for coolant (cold)Engine water jacket with web cooling channels and restrictor pinsCoolant supply gallery (cold) from radiator via coolant pump676_08160Restrictor pinsIt is very important to provide cooling to the cylinder webs of the engine. Because they have a narrow cross-section, the coolant does not flow through them as easily. The coolant naturally always follows the path of least resistance. To ensure that sufficient coolant can flow through the cylinder webs, constrictions must be created at other areas of the engine water jacket. It is not possible to do this with the casting technique used to manufacture the cylinder block, so restrictor pins are installed at the appropriate positions. Two restrictor pins are installed in each cylinder bank.Restrictor pin676_091Engine water jacket Restrictor pinCylinder web cooling676_028NoteWhen making repairs in this area, it is important to ensure that the restrictor pins are installed. Without them, there would be no cylinder web cooling. This would cause the cylinder web areas to overheat, and certain components would become distorted. If a cylinder head were to warp causing a head gasket leak, coolant could leak into the combustion chamber.61Cooling concept for the cylinder headThe cylinder heads have the greatest cooling requirement compared to the other components in the cooling system. The flow to cylinder block and cylinder head is distributed at a ratio of 20:80, with up to 39.62 gal (159.0 L). of coolant per minute per cylinder head.Breather pipe - coolant to coolant expansion tank in vehicleOutlet side - coolant outflow to distribution gallery for crankcase (hot)Coolant intake passages from coolant supply gallery for crankcase (cold)676_083Flow around valve seat inserts (outlet side)Flow around valve seat inserts (inlet side)676_08462Components on the engineView of frontRadiator return (cold) Mechanical Coolant Pump Switch Valve N649 Coolant distribution moduleEngine Temperature Sensor G407 Map Controlled Engine Cooling Thermostat F265 Radiator supply (hot)676_085View of transmission sideCoolant supply line turbochargerCoolant return line turbochargerCoolant line for transverse pipeHeating supply lineCoolant line for transmission coolingHeating return lineAfter-Run Coolant Pump V51676_086After-Run Coolant Pump V51V51 is activated when greater cooling is required for the turbochargers at high engine loads. In addition, the pump operates for a defined period after the engine is switched off. This helps prevent heat-soak in the turbochargers. The electric radiator fan runs as well. To activate V51, the thermal management system performs calculations using the engine speed, engine torque, ambient temperature and coolant temperature.› The after-run time lasts between 10 and 45 minutes (depending on the operating status of the engine). › Delivery rate ~ 132.0 gal (500 L) per hour.63Coolant distribution moduleThe primary component of the thermal management system is installed on the front of the engine. In the coolant distributor housing, the flow of coolant is directed to the radiator, ancillaries and engine. The vacuum-controlled coolant pump and the map-controlled engine cooling system thermostat are located here as well. The coolant pump is driven by the intermediate shaft via a sprocket. When the coolant pump opens the passage for the coolant, it flows through the entire engine, that is, through the cylinder heads as well. In other words, “split cooling” is not used on this engine. The flow to the cylinder block and cylinder head is distributed at a ratio of 20:80. For this reason, only one temperature sensor (G407) is installed for the entire engine; it is installed at an optimal location on the cylinder head of bank 2.Map Controlled Engine Cooling Thermostat F265Coolant from radiator (cold)Coolant to radiator (hot)To belt-driven starter-alternatorOil Pressure Sensor G10676_087Map Controlled Engine Cooling Thermostat F265Coolant return (hot) to radiator via thermostat and coolant pumpCoolant return (hot) from ancillaries directly to coolant pumpCoolant supply (cold) from radiatorCoolant pump/vacuum regulating assemblyCoolant supply (cold) from radiator676_08864Map Controlled Engine Cooling Thermostat F265The coolant temperature calculated in the characteristic map can be regulated between 201.2 °F - 222.8 °F (94 °C - 106 °C) as required. If the temperature is above 201.2 °F (94 °C), the ECM actuates the map-controlled engine cooling system thermostat via a PWM signal. To protect the engine, the coolant temperature is lowered (F265 is not actuated) in the following situations:› › › › › Driving mode Sport. Vehicle speed greater than 124.2 mph (200 km/h). Engine torque 438.8 lb ft (595 Nm). Engine temperature greater than 246.2 °F (110 °C). System DTCs.676_089Map Controlled Engine Cooling Thermostat F265Coolant distribution moduleGasket676_022Coolant pump/vacuum regulating assemblyReferenceFor more information about the map-controlled engine cooling thermostat please refer to eSelf-Study Program 920173, The Audi 3.0L V6 TFSI EA839 Engine.65Regulating strategy of the mechanical coolant pumpThe on-demand mechanical coolant pump is activated when the following conditions are met:› Coolant temperature between -14 °F - 176 °F (10 °C - 80 °C). › Ambient temperature greater than 50 °F (10 °C). › Engine torque greater than 368.7 lb ft (500 Nm) with all cylinders activated. › Engine torque greater than 110.6 lb ft (150 Nm) with half of cylinders activated, depending on the coolant temperature and engine speed. › Time since engine start greater than 600 seconds (10 minutes).If a signal is sent indicating the need to heat the passenger compartment during the engine warm-up phase, the impeller of the mechanical coolant pump is covered by the sleeve and Coolant Recirculation Pump V50 is switched on. In this way, pump V50 pumps coolant from the cylinder head into the heat exchanger.Conditions prohibiting activation:› Coolant temperature greater than 176 °F (80 °C). › Engine speed greater than 3250 rpm.Mechanical Coolant Pump Switch Valve N649 SleevePump gear Drive gearCover plateVacuum regulating unit676_09066Transmission coolant circuitHigh Temperature Circuit Coolant Pump V4673 2 1Transmission Fluid Cooling Valve N509 ATF supply lineATF return lineATF heat exchanger676_093ATF return lineATF supply lineN5093V467 ATF heat exchangerN48812676_094Supply flow 1. From radiator outlet 2. Warm coolant from engine Return 3. To distribution pipe (hot), engine N488 Transmission Coolant Valve N509 Transmission Fluid Cooling Valve V467 High Temperature Circuit Coolant PumpThe transmission coolant circuit can operate in three different system states: Standing coolant› N509 supplied with current (valve closed). › V488 not supplied with current (valve closed). › V467 not running.ATF heating› N509 supplied with current (valve closed). › N488 supplied with current (valve open). › V467 running.ATF cooling› N509 not supplied with current (valve open). › N488 not supplied with current (valve closed). › V467 running.67Transmission Fluid Cooling Valve N509 and Transmission Coolant Valve N488These map-controlled solenoid valves control the inflow of warm coolant from the engine to the ATF cooler/cold coolant from the main radiator to the ATF cooler. Both valves are supplied with 12 Volt current. To activate them, the corresponding control module switches them to ground. Valve N509 is activated by Transmission Control Module J217, which closes it. Activation is initiated by the thermal management system of the ECM. The valve is open when it is not supplied with current. N488 is activated by the Engine Control Module J623. The valve is closed when it is not supplied with current.High Temperature Circuit Coolant Pump V467This pump is identical in form to pumps V50 and V51. It is responsible for pumping the coolant through the transmission coolant circuit.676_095NoteValves N488 and N509 look similar and are easily mistaken for one another; however, the part numbers are different.68Air supplyOverview of air ductsDifferent versions of the air supply system are used depending on the vehicle type and engine power output. The system shown here is for the 2020 Audi A8L. The air pipe connected to the air cleaner distributes intake air to both turbochargers.Air pipeConnection for crankcase breatherCharge Air Pressure Actuator 2 V546 Manifold Absolute Pressure Sensor 2 G429Throttle Valve Control Module GX3Throttle Valve Control Module 2 GX4676_09669Intake sideAn inlet guide element is installed in the air pipe at the point where the air pipe connects to the turbocharger. This calms the flow of air before it enters the turbocharger. In addition, the air flow is given a slight “swirl” in the direction of the fan blades, which improves the acoustics of the air intake.From air cleanerInlet guide elementPressure side676_097The air compressed in the turbochargers is channeled to the charge air coolers via pulsation dampers as an acoustic measure against air noise. The connecting pipe joins both outlets of the turbochargers with one another. This dampens out-of-phase pressure oscillations and helps prevent compressor surge.From air cleaner From charcoal canisterPulsation damperConnecting pipe676_112676_142Pulsation damper Pulsation damper70Intake manifoldsThe intake manifolds are bolted to the cylinder heads. A throttle valve module is installed upstream of each intake manifold. EA825 engines do not require intake manifold flaps. Both intake manifolds have connections for the activated charcoal canister and crankcase breather. Fuel vapors/ blow-by gases enter the intake manifold when there is vacuum pressure inside it. The third connection is for the brake servo (note: the connection on the intake manifold for bank 1 is non-functional).Manifold Absolute Pressure Sensor G71 Intake manifold, bank 1 Manifold Absolute Pressure Sensor 2 G429 Intake manifold, bank 2 Throttle Valve Control Module 2 GX4Throttle Valve Control Module GX3676_113The intake manifold pressure sensors measure the intake manifold pressure and the temperature of the intake air. The ECM uses the signals from the sensor downstream of the throttle valves to measure the air mass (volumetric efficiency measurement).The signals from the sensors upstream of the throttle valves are used by the ECM to calculate and set the desired charge pressure. The signals are transmitted to the ECM by SENT protocol.Manifold Absolute Pressure Sensor 2 G429Connection for brake servo to intake manifold, bank 1 (blind)Charcoal canister connectionCrankcase Ventilation Thermal Resistor 2 N483Throttle Valve Control Module 2 GX4676_11471Throttle Valve Control Modules GX3 and GX4A throttle valve module is installed upstream of each intake manifold. Non-contact throttle valve position sensors (Hall sensors) are used to determine the position of the throttle valves. They operate on the principle of redundancy, meaning that the feedback regarding the position of the throttle valve is delivered by two sensors working independently of and opposed to one another. A DC motor with a two-stage gear assembly acts as an actuator for the throttle valve. This keeps the throttle valve positioned between the two mechanical limit stops. The position of the throttle valve is calculated based on the position of the accelerator pedal and the required engine torque.DC motor power supplyDC motorElectrical connectionSensor unitThrottle valveTwo stage gear assembly676_115NoteThere are no master list terms for the throttle valve position sensors.72TurbochargingTwin scroll exhaust manifoldThe exhaust manifolds have a twin scroll design. With this separation, two cylinders create one stream of exhaust which is kept separate in its own channel inside the turbocharger until it reaches the turbine. Keeping the channels separate helps prevent the individual cylinders from affecting one other adversely during gas exchange. Background: The firing order on each cylinder bank creates a 180° firing interval for some cylinders. The exhaust compression waves (created when the valves open) from these cylinders would affect one another if they were able to interact via the exhaust manifold. This, in turn, directly affects the gas exchange, because the volume of fresh air would be reduced. The twin scroll design keeps the gases from those cylinders separate which correspond unfavorably with one another. This provides a significant torque advantage in the low engine RPM range.Exhaust manifolds located in the inner V of the engine.Twin scroll exhaust manifold676_145676_01173Twin scroll turbochargersThe gas flow paths are very short because the turbochargers are located centrally in the inner V of the engine. As a result, turbocharger response is very direct. The turbines rotate in opposite directions: The turbine on bank 1 rotates counter-clockwise; the one on bank 2 rotates clockwise. This design makes the best use of the space available.676_118Oil return line Coolant supply lineVacuum unit for charge pressure regulating valve676_13974Twin scroll turbochargers continuedTwin scroll turbocharger Turbine (intake side) Turbine (exhaust side)Charge pressure regulating valveTwin scroll exhaust manifold676_14075Turbocharger mountingThe turbochargers are secured to the exhaust manifolds with screw-type clips (V-band clamps). A gasket (made of mica-based material) seals off the connection between the two components. The hot side of the turbocharger and the exhaust manifold are surrounded by insulating covers. This protects the adjacent components in the inner V and helps conserve a larger percentage of the exhaust energy.Screw-type clip (V-band clamp)676_138Insulating cover for exhaust manifoldScrew-type clip (V-band clamp)SealLocating pin for V-band clamp (assembly aid)Integral insulation (temperature can be lowered by up to 752 °F (400 °C)676_08276Turbocharger oil and coolant connectionsThe turbochargers are incorporated in the engine oil and coolant circuits to ensure that the turbine shafts and bearing are lubricated and cooled. Coolant circulates through the turbochargers for a defined period of time after a hot engine has been switched off. This prevents heat soak and protects the components.676_119Oil return lineCoolant supplyCoolant supply lineCoolant returnHeat protection on silicone hoses below the turbochargers676_120676_14177Heat shield in inner V of engineThe exhaust manifolds are located in the inner V of the engine (HSI). The adjacent components require protection to prevent them from becoming too hot. Additional heat shields are installed for this purpose in the inner V along with the heat shields on the exhaust manifolds and turbochargers. A heat shield is installed as additional protection under the engine compartment cover. This cover should always be in place when the engine is running. You can only ensure that cool air reaches the inner V of the engine unless all the components are properly installed. All supply lines in the inner V are also made of heat-resistant materials (stainless steel, silicone) and in some cases are installed with additional heat shields. Engine Cover Temperature Sensor G765 monitors the temperature levels in the inner V of the engine. If the NTC thermistor registers temperatures that are too high, the ECM initiates cooling measures.Engine compartment coverHeat shieldHeat shield for oil filter moduleEngine Cover Temperature Sensor G765Side plateInner heat shield. Protects the sensors and piston cooling jet control valve676_12178Exhaust systemThe exhaust system shown is designed for versions with PR numbers EU6 AD/E/F (7CN), EU6 plus (7MM), ULEV125 (7MU) and EU4 (7GH). Oxygen sensor control is done by a broad-band Oxygen Sensor before the pre-catalytic converter and a two-state sensor after it. Due to limited space, an additional catalytic converter is located in the area of the underbody.GX10GX11 GX8GX7J883J945676_100Key: GX7 Oxygen Sensor 1 After Catalytic Converter G130 Oxygen Sensor After Catalytic Converter Z29 Heater for Oxygen Sensor 1 After Catalytic Converter GX8 Oxygen Sensor 2 After Catalytic Converter G131 Oxygen Sensor 2 After Catalytic Converter Z30 Heater for Oxygen Sensor 2 After Catalytic Converter GX10 Oxygen Sensor 1 Before Catalytic Converter G39 Heated Oxygen Sensor Z19 Oxygen Sensor Heater GX11 Oxygen Sensor 2 Before Catalytic Converter G108 Heated Oxygen Sensor 2 Z28 Oxygen Sensor 2 Heater J883 Exhaust Door Control Unit J945 Exhaust Door Control Unit 279Fuel systemFuel is supplied from the fuel tank to high pressure pumps on the engine by an electric pump. The pressure varies from 43.51 to 79.77 psi (3 to 5 bar). The system does not have a fuel return line. The amount of fuel required is calculated by the ECM; the amount supplied is always just enough to prevent bubbles from forming in the system. Low Fuel Pressure Sensor G410 in the low-pressure pipe to monitor the low pressure in the system. Due to the greater fuel requirement for the V8 engine, each cylinder bank has its own high-pressure fuel pump. Each cylinder bank has its own high-pressure supply. The two systems are not connected to one another on the high-pressure side.Overview of the high-pressure systemLow Fuel Pressure Sensor G410Fuel Metering Valve 2 N402Fuel Metering Valve N290High-pressure lineFuel Pressure Sensor G247Cylinder 4 Fuel Injector N33 Cylinder 3 Fuel Injector N32 Cylinder 2 Fuel Injector N31 Cylinder 1 Fuel Injector N30Cylinder 8 Fuel Injector N86 Cylinder 7 Fuel Injector N85 Cylinder 6 Fuel Injector N84 Cylinder 5 Fuel Injector N83Fuel Pressure Sensor 2 G624 High-pressure rail676_104High pressure fuel pumps The high-pressure fuel pumps are driven by roller tappets and four-lobe cams positioned on the exhaust camshafts. The maximum pressure generated is 3625.94 psi (250 bar). At approximately 4351.13 psi (300 bar), the pressure limiting valve in the pump opens. The pump is open when no current is applied (fail-safe). This means that without electric actuation, the pump runs at the same pressure as the supply from the pump in the fuel tank.High-pressure fuel pump High-pressure connectionRoller tappet Four-lobe camsExhaust camshaft676_10280High-pressure injectorThe injector is positioned directly next to the spark plug. This central position, together with adjustments to the injector hole diameter and the spray pattern suited to the conditions in the cylinder, helps provide the most homogeneous fuel distribution possible.› › › › › › › 7-hole injector. Injector hole diameter: 0.007 in (0.19 mm). Needle lift: 0.0027 in (0.07 mm). Up to 65 V actuation. Injection period: 0.3 - 6 ms. Up to 3 injections possible (depending on engine speed). Injection pressure: approximately 1015.26 to 3625.94 psi (70 to 250 bar).High-pressure fuel pumpExhaust camshaft (four-lobe)Spark plug (spark plug aperture)7-hole injector (positioned centrally in cylinder head)Spray pattern of 7-hole injector (in combustion chamber)676_106Fuel supply rail connection Electrical connectionInjector holesCross-section of injector holesTeflon ring676_103 676_128 676_12281Engine managementSystem overviewAccelerator Pedal Module GX2 Accelerator Pedal Position Sensor G79 Accelerator Pedal Position Sensor 2 G185 Cruise Control Switch E45 Transmission Coolant Valve N488 Oil Pressure Switch F1 Oil Temperature Sensor G8 Tank Ventilation Pressure Sensor 1 G950 Tank Ventilation Pressure Sensor 2 G951 Oil Pressure Sensor G10 Oil Level Thermal Sensor G