TECHNICAL DOCUMENTATION

SSP 970563 – The 2017 A4 Electronic and Electrical Systems

PDFEN66 pages4 MB
SSP 970563 – The 2017 A4 Electronic and Electrical Systems - PDF cover

This PDF is currently unavailable.

Read document text
eSelf Study Program 970563The 2017 A4 Electronic and Electrical Systemsi Audi of America, LLC Service Training Created in the U.S.A. Created 12/2015 Course Number 970563 ©2015 Audi of America, LLC All rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC. Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.This eSSP contains video links which you can use to access interactive media.Revision 1:12/2015ii Introduction .......................................................................................1 Voltage supply.....................................................................................2Vehicle battery ........................................................................................................................................................... 2 Jump start terminal ................................................................................................................................................... 3 Power distribution ..................................................................................................................................................... 4 Fuses and relays ........................................................................................................................................................ 5 Aluminum wires ......................................................................................................................................................... 6Networking..........................................................................................8Installation locations of control modules ............................................................................................................... 8 Topology ...................................................................................................................................................................10 Bus systems used on the Audi A4 ..........................................................................................................................12Control units..................................................................................... 14Brief descriptions .....................................................................................................................................................14Exterior lighting............................................................................... 37Headlight variants ...................................................................................................................................................37 Xenon headlight .......................................................................................................................................................39 LED headlight ...........................................................................................................................................................41 Tail lights ..................................................................................................................................................................43 High-mounted brake light / license plate lights ...................................................................................................44 Interior lighting .......................................................................................................................................................45 Overhead module ....................................................................................................................................................49Audi drive select............................................................................... 50Functional characteristics .......................................................................................................................................50 Displays and operation ............................................................................................................................................50 Audi drive select function .......................................................................................................................................51 Functional features .................................................................................................................................................51 Anti-theft alarm .......................................................................................................................................................52 Central locking .........................................................................................................................................................54 Garage door opener (HomeLink) ............................................................................................................................56 Head-up display .......................................................................................................................................................58Self-study programs......................................................................... 59 Knowledge assessment.................................................................... 60This eSelf Study Program teaches a basic knowledge of the design and functions of new models, new automotive components or technologies. It is not a Repair Manual! All values given are intended as a guideline only. For maintenance and repair work, always refer to the current technical literature.NoteReferenceiii iv IntroductionThe 2017 Audi A4 is the second Audi vehicle to adapt the MLBevo (Modular Longitudinal Platform evolution). A fully equipped A4 has approximately 90 control modules, many of which exchange information with one another. The FlexRay bus system is now used on an A4 model for the first time. It helps ensure data is transmitted quickly and securely. The key components on the FlexRay are the engine control module, the transmission control module, a new central suspension control module, the ESC, power steering control module and ACC. In addition to the FlexRay bus CAN bus systems (CAN = controller area network) integrate the climate control system and several assistance systems such as Audi side assist and the surround cameras. They also facilitate communication between the comfort/ convenience control modules, the infotainment modules and central display and operating components such as the MMI and Audi virtual cockpit. LIN buses (LIN = local interconnect network) complement the CAN buses by serving less complex systems such as the interior lighting. The Audi A4 now also has aluminum high-current wires with diameters of 16 mm2, 35 mm2 and 50 mm2. It is also the first Audi to use aluminum wires with diameters of 2.5 mm2, 4 mm2 and 6 mm2. Thanks to these modifications, the weight of the vehicle in this area has been reduced by approximately 13 lb (5 kg) compared with the previous model.646_002Learning objectives of this Self-Study Program: Once you have completed this eSelf-Study Program program you will be able to answer the following questions: • Where are the fuse and relay panels located in the Audi A4? • In what locations are electrical components installed on the car? • Which bus systems are used in the Audi A4?1• What are the tasks of the control modules in the car? • What are the versions of the exterior lighting, and how are the individual light functions implemented? Voltage supplyVehicle batteryThe vehicle battery is housed centrally in the spare wheel well. The main fuse panel as well as Battery Interrupt Igniter N253 are mounted on the positive terminal. In the event of a crash, N253 disconnects the main battery lead from the vehicle electrical system. Battery Monitoring Control Module J367 (BDM) is located at the negative battery terminal.Battery Monitoring Control Module J367Battery AMain fuse panel and Battery Interrupt Igniter N253646_0812 Jump start terminalThe positive jump start terminal is located under a red plastic cover on the right hand side of the engine compartment. A negative terminal is attached directly to the body at the right suspension strut tower. These terminals should also be used for maintaining the battery in the showroom or when performing diagnostic work.Positive Jump start terminal Terminal 30 Wire Junction TV2 with fusesTerminal 30 supplyDistribution supply lineSuppressor C24Sealing capGround terminalTerminal 30 Wire Junction 2 TV22Starter/alternator cableConnection to Radiator Fan Control Module J293 (4-cylinder engines) Connection to Secondary Air Injection Pump Relay J299Connection to Radiator Fan Control Module 2 J671646_0823 Power distributionThis is a schematic diagram of the A4 power distribution structure. For exact details of fuse assignment and the cable routing, please refer to the applicable service literature.TV22TV2SCTV1*SBMain fuse panel SFKey:646_0831 2 3 4 5 6 Not used in North American Region Not used in North American Region Connection to Radiator Fan Control Module J293 (4-cylinder engines) Connection to Secondary Air Injection Pump Relay J299 Connection to Radiator Fan Control Module 2 J671 Connection to Radiator Fan Control Module J293A Battery B Starter motor C AlternatorJ367 Battery Monitoring Control Module J500 Power Steering Control Module N253 Battery Interrupt Igniter SB Fuse panel B, on the footrest SC Fuse panel C, under instrument panel, right side SF Fuse panel F, in luggage compartment on left side TV1* Wire Junction, base of right ‘A’ pillar TV2 Terminal 30 Wire Junction TV22 Terminal 30 Wire Junction 24*Not for North American Market Fuses and relaysThe fuses on the main fuse panel as well as distributors TV1* and TV22 are labeled only "S" in the Wiring Diagrams. This also applies to other individual fuses distributed throughout the car. Fuses "SB", "SC" and "SF" can also be accessed by the driver behind the relevant fuse panels and therefore are also described in the Owner's Manual.Relay and fuse panel in plenum chamberTerminal 30 Wire Junction and Terminal 30 Wire Junction 2 with fusesDistributor for Wire Junction TV1* with fusesMain battery lead646_084Fuse panel C on the dash panel, driver side. The fuses here are labelled "SC" in the Wiring DiagramsFuse panel B on the driver side footrest. The fuses here are labelled "SB" in the Wiring DiagramsFuse panel F in the luggage compartment, rear left. The fuses here are labelled "SF" in the Wiring DiagramsMain fuse panel at positive terminal of vehicle batteryBattery Monitoring Control Module J367 at negative terminal of vehicle battery*Not for North American Market5 Aluminum wiresMain battery leadThe main positive battery cable in the Audi A4 is made of aluminum like the Audi A8 where this was used for the first time. The cable begins at the main fuse panel as a flexible round cable. On the right hand-side of the luggage compartment, it is welded onto a flexurally rigid aluminum ribbon cable. This ribbon cable runs along the right-hand side of the vehicle through the rear section of the vehicle and under the rear seat, terminating in the heel panel area. Here it is welded onto a round cable which continues along the inside of the right-hand sill and through the engine bulkhead to the jump start terminal in the engine compartment. If defective, the battery cable can only be replaced. There is no provision for repairs.Wiring harnessA new feature is the use of aluminum wires with diameters of 2.5 mm2, 4 mm2 and 6 mm2 in certain areas of the wiring harness. This helps save weight in the electrical system. Copper wires with diameters from 1.5 mm2 to 6 mm2 are also used, particularly in areas in which wires are subject to movement, for example, on the hood.Repairing aluminum wires A new tool, VAS 631 001 has been developed for repairing aluminum wires. In addition to a crimping pliers, this repair kit includes a wire stripper and a special crimp connector including heat shrink tubing for wire diameters of 2.5 mm2, 4 mm2 and 6 mm2. As before, copper wires can be repaired using the wiring harness repair kit VAS 1978B. Cut wires can be reconnected using crimp connectors. Repair wires with industrial manufactured contacts are also available.Crimping pliersWire stripperHeat shrink tubing646_087Crimp connector6 Special crimp connectors are used for the repair of aluminum wires. These connectors ensure strain resistant connection of the aluminum wires. The supplied heat shrink tubing reliably protects the joints against moisture.A cut aluminum wire can be reconnected using this crimp connector. If it is necessary to attach a new section of wires, the copper repair wires from repair kit VAS 1978A can be used.Transition zoneInsulation fittingWire crimping sleeve with serrations and additiveCoding for wire diameter in crimping pliersCode for wire diameter (both sides)646_088Challenges in repairing aluminum wires: 1. T he crimp connector must provide a strain resistant connection. To achieve a strain resistant connection with the aluminum wires, the oxide layers on the individual strands of the aluminum wires must be broken. This is achieved by the serrations in the crimp connectors. These serrations are also coated with an additive to provide better corrosion protection. 2. The joint must be sealed.Because copper repair wires are used, there is an aluminum wire on one side of the connector and a copper wire on the other side. To prevent electro-chemical corrosion, the joint must be reliably protected. The heat shrink tubing supplied with the crimp connector is used for this purpose.Oxide layerHeat shrink tubing646_090 646_089Cable strandOxide layer broken by serrations in connectorHeat shrink tubing (after heat applied)Reference For a detailed description of how to repair aluminum wires, please refer to the Workshop Manual. At the vehicle introduction, the aluminum wire repair tools can be rented from Equipment Solutions.7 NetworkingInstallation locations of control modulesSome of the control modules shown in the overview are optional and/or country-specific equipment. Refer to the current service literature for details of control module installation positions as well as instructions for installation and removal.J428J387J1023A27J794J685 J500 J217 E87J844 R242E380J245 J587J764 J898 J285 J527J623 A31 J104J792J1018 J519 J850 J386Key:A27 Right LED Headlamp Power Output Module 1 A31 Left LED Headlamp Power Output Module 1 E87 Front A/C Display Control Head E265 Rear A/C Display Control Head E380 Multimedia System Control Head J104 J136 J217 J234 J245 J285 ABS Control Module Memory Seat/Steering Column Adjustment Control Module Transmission Control Module Airbag Control Module Power Sunroof Control Module Instrument Cluster Control Module J386 J387 J393 J428 J492 J500 J519 J521 J525 J527 J533 Driver Door Control Module Front Passenger Door Control Module Comfort System Central Control Module Distance Regulation Control Module All Wheel Drive Control Module Power Steering Control Module Vehicle Electrical System Control Module 1 Front Passenger Memory Seat Control Module Digital Sound System Control Module Steering Column Electronics Control Module Data Bus On Board Diagnostic Interface8 J927 J769J649J521J492J234J775E265J772 J533J136J648J393 J525 J928 J926 J770644_113J587 J623 J648 J649 J685 J764 J769 J770 J772 J775 Selector Lever Sensor System Control Module Engine Control Module Left Rear Information Display Control Head Control Module Right Rear Information Display Control Head Control Module Front Information Display Control Head Electronic Steering Column Lock Control Module Lane Change Assistance Control Module Lane Change Assistance Control Module 2 Rearview Camera System Control Module Drivetrain Control ModuleJ792 Active Steering Control Module J794 Information Electronics Control Module 1 J844 Automatic High Beam Assist Control Module J850 Distance Regulation Control Module 2 J898 Windshield Projection Head Up Display Control Module J926 Driver Side Rear Door Control Module J927 Passenger Side Rear Door Control Module J928 Peripheral Camera Control Module J1018 Left Light Control Module J1023 Right Light Control Module R242 Driver Assistance Systems Front Camera9 TopologyFlap Control Motors 1 ­ – 15Front A/C Display Control Head E87Driver Side Rear Door Control Module J926Driver Door Control Module J386Fresh Air Blower Control Module J126Humidity Sensor In Fresh Air Intake Duct G657 Air Quality Sensor G238Passenger Side Rear Door Control Module J927Front Passenger Door Control Module J387High Pressure Sensor G65Data Link Connector Memory Seat/ Steering Column Adjustment Control Module J136 Rear A/C Display Control Head E265Electronic Steering Column Lock Control Module J764 Data Bus On Board Diagnostic Interface J533Left Front Seat Backrest Fan 1 V512Garage Door Opener Control Head E284Light switch E1Left Front Seat Cushion Fan 1 V514Garage Door Opener Control Module J530 Automatic Dimming Interior Rearview Mirror Y7 Roof Electronics Control Module J528Wiper Motor Control Module J400Power Sunroof Control Module J245Right Front Seat Backrest Fan 1 V516Rain/Light Recognition Sensor G397Right Front Seat Cushion Fan 1 V518Humidity Sensor G355Vehicle Electrical System Control Module J519Anti-Theft Alarm System Sensor G578Alarm Horn H12Interior light moduleInterior light moduleComfort System Central Control Module J393Key:Convenience CAN Hybrid CAN Extended CAN Infotainment CAN10Diagnostics CAN FlexRay Modular Infotainment Platform (MIB) CAN LIN bus Left Rear Information Display Control Head Control Module J648 Driver Volume Control E67 Right Rear Information Display Control Head Control Module J649 Multimedia System Control Head E380Digital Sound System Control Module J525Multimedia Button Module E817Information Electronics Control Module 1 J794Instrument Cluster Control Module J285Battery Monitoring Control Module J367Front Information Display Control Head J685 Selector Lever Sensor System Control Module J587 Windshield Projection Head Up Display Control Module J898 Peripheral Camera Control Module J928orMultifunction Steering Wheel Control Module J453Alternator CLeft Light Control Module J1018Driver Assistance Systems Front Camera R242Engine Control Module J623Rearview Camera System Control Module J772Right Light Control Module J1023ABS Control Module J104Radiator Shutter Motor V544Left LED Headlamp Power Output Module 1 A31 Right LED Headlamp Power Output Module 1 A27Power Steering Control Module J500Radiator Shutter Adjustment Motor 2 V550Automatic High Beam Assist Control Module J844 Left Front Seat Belt Tensioner Control Module J854 Right Front Seat Belt Tensioner Control Module J855 Passenger Occupant Detection System Control Module J706 Lane Change Assistance Control Module J769 Lane Change Assistance Control Module 2 J770Drivetrain Control Module J775Active Steering Control Module J792Steering Column Electronics Control Module J527 Control Unit 1 for Driving and Convenience Functions E791 Distance Regulation Control Module J428Airbag Control Module J234Distance Regulation Control Module 2 J850 Transmission Control Module J217All Wheel Drive Control Module J492Transmission Electric Pump 2 V553644_114_revSub-bus systems MOST bus LVDS FBAS"OR" configuration Ethernet port for diagnose interface VAS 615411 Bus systems used on the Audi A4Bus system Hybrid CAN Convenience CAN Extended CAN Infotainment CAN Modular Infotainment Platform (MIB) CAN Diagnostics CAN FlexRay MOST bus Cable color Configuration Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Fiber-optic bus system Max. data transfer rate 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 10 Mbit/s 150 Mbit/s Property not single wire capable not single wire capable not single wire capable not single wire capable not single wire capable not single wire capable not single wire capable Ring structure: an open circuit will result in total system failure single wire capable not single wire capable not single wire capable single wire capableLIN bus Sub-bus system LVDS FBASElectrical single-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical single-wire bus system20 kbit/s 500 kbit/s approx. 200 Mbit/s approx. 80 Mbit/sThe network diagram on page 10 provides a schematic overview of the communication paths between the control modules in the Audi A4. The bus systems used in the Audi A4 are identical to those of the Audi Q7.If we compare the 2017 Audi A4 with the predecessor model), new features in the area of data transmission are the FlexRay, MOST150 and LVDS buses. In spite of the many similarities with the 2017 Audi Q7, there are a few differences that are not exclusively equipment-specific. For this reason, the topologies in the areas of infotainment and FlexRay are described below.Infotainment topologyIn the Audi A4 three control modules are integrated in the MOST ring in the following order: • Information Electronics Control Module 1 J794. • Instrument Cluster Control Module J285. • Digital Sound System Control Module J525. When compared to the 2017 Q7, the difference is that the DVD Changer is not on the MOST ring in the 2017 A4. Driver Volume Control E67 is configured as the LIN slave of Multimedia System Control Head E380.J525 R78(not for the NAR)E67E817E380J794J285J685J587J898J533orJ928Key: Infotainment CAN Modular Infotainment Platform (MIB) CAN LIN bus MOST bus LVDS FBAS Ring break diagnostics line "OR" configurationJ772646_051Reference For further information and general descriptions of the MOST150 and FlexRay buses, refer to Self-Study Program 970163, The 2017 Audi Q7 On-board Power Supply and Networking System.12 FlexRay topologyData Bus On Board Diagnostic Interface J533 is the controller for the FlexRay bus. All FlexRay control modules are connected to J533 via various branches. In this configuration J533 is referred to as the "active hub" or "active node". If only one control module is connected to a branch, this is referred to as a "point to point" connection. A configuration in which more than one control module is connected to a branch is known as a "daisy chain connection". In the Audi A4, six branches are used: branches 1 – 5 and branch 8. The pins of branches 6 and 7 are reserved in the current version of J533, but are still not assigned.ABS Control Module J104 Engine Control Module J623Power Steering Control Module J500 Transmission Control Module J217Steering Column Electronics Control Module J527 Driver Assistance Systems Front Camera R242 Drivetrain Control Module J775Branch 1Branch 2Branch 3Data Bus On Board Diagnostic Interface J533Branch 5 Branch 8Branch 4Distance Regulation Control Module 2 J850 Distance Regulation Control Module J428Active Steering Control Module J792Airbag Control Module J234All Wheel Drive Control Module J492646_052In configuring of the control modules, a distinction is made between the bus positive cable (pink) and the bus negative cable (green). Two resistors each having a resistance of 47 Ω (94 Ω in total) are always connected at the beginning and end of a branch. Each of the center control modules has two resistors with a resistance of 1.3 Ω, i.e. 2.6 Ω in total.A control module from the vehicle's standard specification is always connected at the end of a branch. This ensures that there is a resistance of 94 Ω at the end of each branch. Two optional control modules, which are integrated in other models as center control modules, are connected to branch 8 in the Audi A4. The FlexRay line is routed back to J533. The resistance here is 94 Ω - the value required for the termination of branch 8.J10447 Ω 47 ΩJ50047 Ω 47 ΩJ52747 Ω 47 ΩJ6231.3 kΩ 1.3 kΩJ2171.3 kΩ 1.3 kΩR2421.3 kΩ 1.3 kΩJ7751.3 kΩ 1.3 kΩBranch 147 Ω 47 Ω 47 Ω 47 ΩBranch 2Branch 347 Ω 47 Ω 47 Ω 47 Ω 47 Ω 47 ΩJ53347 Ω 47 Ω47 Ω 47 ΩBranch 4Branch 51.3 kΩ 1.3 kΩBranch 81.3 kΩ 1.3 kΩJ850J79247 Ω47 Ω47 Ω47 Ω1.3 kΩ 1.3 kΩJ234J428J492646_05313 Control unitsBrief descriptionsVehicle Electrical System Control Module J519646_012Connector C (54-pin) to cockpit wiring harnessConnectors A and B (each 73-pin) to vehicle / engine compartment14 Designation Equipment Installation location TasksVehicle Electrical System Control Module J519 / also referred to as BCM1 (Body Control Module 1) Always installed On left ‘A’ pillar above the hood release lever Exterior lighting master Interior lighting master Diagnostic gateway for the light control modules A/C functions • Activation of seat heater and front seat ventilation • Activation of A/C Compressor Regulating Valve N280 Integration functions • Parking • Parking aid • Ambient lighting • Activation and supply of LIN interior light modules • Headlight range adjustment • Calculation of headlight range adjustment • Activation of headlight range adjustment via the left and right control modules for light control J1018 and J1023. • Reading input of the signals from the inclination sensor via the CAN line Other functions • Reading input from (senders/sensors/switches) • Ambient temperature • Engine coolant, windshield washer fluid, brake fluid • Brake pad wear • Hood contact • Seater heater temperature • Activation (actuators/control elements) • Relay for sockets • Signal horn • Headlight washer system • Windshield washer pump (dual pump) • Heating the windshield washer jets • Seat heater, frontAddress Word Data bus communication09 • Convenience CAN participant • J519 is the LIN master for • LIN 1: Light Switch E1, Wiper Motor Control Module J400, Rain/Light Recognition Sensor G397, and Humidity Sensor G355 • LIN 2: Garage Door Opener Control Head E284, Garage Door Opener Control Module J530, Automatic Dimming Interior Rearview Mirror Y7, Roof Electronics Control Module J528 • LIN 3: Left Front Seat Backrest Fan 1 V512, Left Front Seat Cushion Fan 1 V514, Right Front Seat Backrest Fan 1 V516, Right Front Seat Cushion Fan 1 V518 • LIN 4: Control Unit 1 for Driving And Convenience Functions E791 • LIN 5: Interior light module • LIN 6: Interior light module • Communicates via a sub-bus system with Left and Right Light Control Modules J1018 and J1023, and Left and Right LED Headlamp Power Output Modules A31 and A27 and left and right LED headlight power modules 1 A31 and A27 Fault finding notes: J519 has duplicated pins at the LIN slave connection. For example, LIN 1 is distributed to 3 pins (A22, A23,C50), which, however, are connected internally within the control module. This means that the control modules connected to pin A23 and C50 are also affected in the event of a short circuit to positive or negative at pin A22 and vice versa.Special feature15 GatewayDesignation Equipment Installation location Tasks Data Bus On Board Diagnostic Interface J533 Always installed Under the rear seat, on the floor pan • • • • • 19 • Hybrid CAN, Convenience CAN, Infotainment CAN, CAN-Extended and FlexRay user • LIN master of Battery Monitoring Control Module J367 and alternator C • LIN master for Multifunction Steering Wheel Control Module J453 • Not a user of the Modular Infotainment Platform (MIB) CAN • Not a user of the MOST bus • Additional variant as "Connected Gateway" Network system Gateway Controller for FlexRay bus Diagnostic master Energy management control Interface for various connect servicesAddress Word Data bus communicationSpecial features646_011Data Bus On Board Diagnostic Interface J53316 Comfort System Central Control ModuleDesignation Equipment Installation location Tasks Comfort System Central Control Module J393 / also referred to as BCM2 (Body Control Module 2) Always installed In luggage compartment on left hand side, behind luggage compartment side trim, under fuse and relay panel Central locking system master Integration functions • Terminal management system • Entry and start authorization • Immobilizer (master) • Anti-theft alarm system Other functions • Reading input (senders/sensors/switches) • Brake light switch • Ignition starter button • P signal • Soft touch button on rear hatch • Rear hatch contacts (pre-lock and full lock) • Capacitive sensors of door handles • Entry and start authorization aerials • Fuel tank sender • Inclination sensors for headlight range adjustment • Activation (actuators/control elements) • Rear hatch lock motor • Luggage compartment release • Fuel tank flap lock • Terminal 15 relay • Heated rear window relay • Luggage compartment lights • Rear lighting Address Word Data bus communication 46 • Convenience CAN participant • J393 is the LIN master for: • LIN 1: Anti-Theft Alarm System Sensor G578 • LIN 2: Alarm Horn H12 • LIN 3: • J393 is the immobilizer system master in the Audi A4 • Central locking antenna is integrated in control moduleSpecial featuresComfort System Central Control Module J393646_01317 Door control modulesDesignation Equipment Installation location Tasks Driver Door Control Module J386 Always installed In driver's door Controlling the electrical and electronic components in and on the driver's door • Reading input (senders/sensors/switches) • Switches/buttons, for example, power windows, rear hatch release, child lock button, door mirror, central locking, seat memory etc. • Activation (actuators/control elements) • Lights and components in and on the door trim, locking motor, turn signals in door mirror 42 • Convenience CAN participant • LIN master for Driver Side Rear Door Control Module J926 J926 has its own Address Word "BB" although it is a LIN slave of J386.Address Word Data bus communication Special featureDriver Door Control Module J386646_014Designation Equipment Installation location TasksFront Passenger Door Control Module J387 Always installed In front passenger's door Controlling the electrical and electronic components in and on the front passenger's door • Reading input (senders/sensors/switches) • Switches/buttons, for example, power windows, rear hatch release, child lock button, electrical door mirror, central locking, seat memory etc. • Activation (actuators/control elements) • Lights and components in and on the door trim, locking motor, turn signals in door mirror 52 • Convenience CAN participant • LIN master for Passenger Side Rear Door Control Module J927 J927 has its own Address Word "BC" although it is a LIN slave of J386.Address Word Data bus communication Special feature18 Seat adjustmentDesignation Equipment Installation location Tasks Address Word Data bus communication Memory Seat/Steering Column Adjustment Control Module J136 Optional equipment (PR no.: PV3) Below the driver's seat Activation (actuators/control elements) • Seat adjustment (memory function) 36 Convenience CAN participantMemory Seat/Steering Column Adjustment Control Module J136646_01519 Steering column lock controlDesignation Equipment Installation location Task Address Word Data bus communication Special features Electronic Steering Column Lock Control Module J764 • Always installed On steering column Locking and unlocking the steering column 2B Convenience CAN participant • Immobilizer user • Can be replaced separately from the steering columnElectronic Steering Column Lock Control Module J764646_017Power sunroof controlDesignation Equipment Installation location Tasks Power Sunroof Control Module J245 Always installed On sliding sunroof frame at front Controlling the functions of the glass sunroof • Reading input (senders/sensors/switches) • Controller for sliding sunroof adjustment • Activation (actuators/control elements) • Motors for Sunroof Motor V1 CA Convenience CAN participantAddress Word Data bus communicationPower Sunroof Control Module J245646_01820 Instrument clusterDesignation Equipment Installation location Task Address Word Data bus communication Instrument Cluster Control Module J285 • Always installed • Optional Audi virtual cockpit (PR no.: 9S8) In instrument panel Display of information relevant to the driver 17 • Infotainment CAN participant • MOST participant • Connected by LVDS bus to Information Electronics Control Module 1 J794 (image transfer for navigation display in instrument cluster). The instrument cluster in the Audi A4 is not integrated with the immobilizer.Special feature646_020646_086Instrument Cluster Control Module J285Instrument Cluster Control Module J285 (Audi vitual cockpit)21 ACC adaptive cruise controlDesignation Equipment Distance Regulation Control Module J428 Optional equipment: • ACC with Stop&Go including traffic jam assist (PR no.: 8T8) • ACC distance indicator (PR no.: 8T3) On lock carrier, front right, behind front bumper cover • Radar scanning of traffic (distance and speed) • Controlling speed and distance • Distance display and distance warnings (only if ACC is deactivated) 13 FlexRay participant • ACC Stop&Go with integrated traffic jam assistant • Distance display and distance warning – display of distance in instrument cluster in seconds • Function master for Distance Regulation Control Module 2 J850Installation location TasksAddress Word Data bus communication Special features646_021Distance Regulation Control Module J428Distance Regulation Control Module 2 J850Designation Equipment Installation location Task Address Word Data bus communication Special featureDistance Regulation Control Module 2 J850 Optional equipment On lock carrier, front left, behind front bumper cover Radar scanning of traffic (distance and speed) 8B FlexRay participant J850 is a slave of J428 and, based on its function, could also be referred to as a sensor.22 Front cameraDesignation Equipment Installation location Tasks Driver Assistance Systems Front Camera R242 Optional equipment On windshield above base of interior rear view mirror Imaging of traffic, traffic signs and lane markers for • Audi active lane assist (lane departure warning system) • High beam assist • Road sign recognition • ACC Stop&Go • Audi pre sense • Collision avoidance assist A5 • FlexRay participant • R242 is connected to the light control modules via a sub-bus system. • Forms a functional unit in combination with image processing control moduleAddress Word Data bus communication Special featuresDriver Assistance Systems Front Camera R242646_02323 Automatic transmissionDesignation Equipment Installation location Task Address Word Data bus communication Special feature Transmission Control Module J217 Installed in combination with: • 7-speed dual clutch gearbox 0CK/0CL – S tronic (PR no.: G1C/G1D) Component part of DSG Transmission Mechatronic J743 Controlling and monitoring the engagement and disengagement operations of the automatic transmission 02 • FlexRay participant • LIN master for Transmission Electric Pump 2 V553 Immobilizer userTransmission Control Module J217 (7-speed dual clutch gearbox 0CK/0CL)646_047Reference For further information about the automatic transmission, refer to Self-Study Program 990263, The 2017 Audi A4 Introduction.24 Selector mechanismDesignation Equipment Selector Lever Sensor System Control Module J587 Installed in combination with: • 7-speed S tronic transmission 0CK/0CL – S tronic (PR no.: G1C/G1D) • 8-speed automaic gearbox 0D5 – tiptronic (PR no.: G1G) Within the selector mechanism at center console Operating the transmission. For example, transmitting drive positions, controlling the mechanical selector lever locks, transmitting selector lever tiptronic commands and resetting the selector lever in the automatic gate. 81 Infotainment CAN bus participant • J587 can only be replaced together with the selector mechanism. • The selector mechanism is not mechanically connected to the transmission.Installation location TasksAddress Word Data bus communication Special featuresSelector Lever Sensor System Control Module J587646_025Reference For further information about the selector mechanism, refer to eSelf-Study Program 990263, The 2017 Audi A4 Introduction25 Steering column electronicsDesignation Equipment Installation location Task Address Word Data bus communication Special feature Steering Column Electronics Control Module J527 Always installed On steering column Connects the steering column stalk and the electrical components in the steering wheel to the vehicle's electrical system 16 FlexRay participant In conjunction with the multifunction steering wheel, it transfers the LIN signals from J533 (master) to Multifunction Steering Wheel Control Module J453 (slave).Steering Column Electronics Control Module J527646_027AirbagDesignation Equipment Installation location Tasks Address Word Data bus communication Airbag Control Module J234 Always installed Under front center console storage bin • Deployment of airbags, seat belt pretensioners and battery interrupt igniter • Audi pre sense 15 • FlexRay participant • Is connected to Left and Right Front Seat Belt Tensioner Control Modules J854 and J855 via a sub-bus system. • LIN master for Passenger Occupant Detection System Control Module J706 Inertial sensors for ESC (ABS Control Module J104).Special featureAirbag Control Module J234646_02826 Engine controlDesignation Equipment Installation location Tasks Engine Control Module J623 Always installed In left hand side of engine compartment in front of air plenum chamber • Controlling the engine characteristic • Activation of Start Relays J906 and J907 • Function master for start-stop system 01 • FlexRay participant • LIN master for Radiator Shutter Motors V544 and V550. • Immobilizer user • Control module with new plug-in connections. Has a total of 315 pins. New test adapter VAS 6606/23 for Test Box VAS 6606Address Word Data bus communication Special featuresEngine Control Module J623646_030Start-stop systemThe Audi A4 is equipped with start-stop system Version 2.0, which was first used in the 2017 Audi Q7. For a history of the start-stop system and a detailed description of Version 2.0, refer to 970163 The 2017 Audi Q7 Onboard Power Supply and Networking System.Control Unit 1 For Driving And Convenience Functions E791646_080aStart/Stop Mode Button E69327 Front climate control panelDesignation Equipment Installation location Tasks Front A/C Display Control Head E87 Always installed • Automatic air conditioning (PR no.: 9AQ) In center of instrument panel Controlling: • Temperature • Fan speed • Air flow distribution 08 • Hybrid CAN participant • E87 is the LIN master for • LIN 1: Control motors for flap activation 1 – 15 • LIN 2: Rear A/C Display Control Head E265, Fresh Air Blower Control Module J126, Humidity Sensor In Fresh Air Intake Duct G657, Air Quality Sensor G238, High Pressure Sensor G65 Although the seat seating and seat ventilation switches are integrated in and monitored by Front A/C Display Control Head E87, the Vehicle Electrical System Control Module J519 is responsible for their activation.Address Word Data bus communicationSpecial featureFront A/C Display Control Head E871)Optional equipment646_02928 Head-up displayDesignation Equipment Installation location Task Address Word Data bus communication Special features Windshield Projection Head Up Display Control Module J898 Optional equipment (PR no.: KS1) for Prestige models In instrument panel directly behind the instrument cluster Controlling all optical, mechanical and electrical components of the head-up display 82 Infotainment CAN bus participant • The control module can only be replaced complete with the other components of the head-up display. • To replace the head-up display, the windshield must be removed. • The head-up display requires a special windshield (with wedge-shaped foil).646_032Windshield Projection Head Up Display Control Module J89829 Rear-view cameraDesignation Equipment Installation location Task Address Word Data bus communication Special feature Rearview Camera System Control Module J772 Standard equipment on all models (PR no.: KA2) In handle (soft touch) on rear hatch Processing and transfer of images from the area behind the vehicle to the Information Electronics Control Module 1 J794 6C Extended CAN participant Control module, camera and wiring harness form a unit (as shown)Rearview Camera System Control Module J772 (with built-in camera)646_033Surround camerasDesignation Equipment Installation location Task Address Word Data bus communication Peripheral Camera Control Module J928 Standard equipment on Prestige model, In luggage compartment, L/H side, behind luggage compartment side trim The control module reads the data from the four surround-view cameras and generates images mapping the area around the vehicle. 6C • Extended CAN participant • Image transfer to instrument cluster by LVDSPeripheral Camera Control Module J928646_03430 Audi side assistDesignation Equipment Installation location Tasks Lane Change Assistance Control Module J769 (master) Lane Change Assistance Control Module 2 J770 (slave) Optional equipment (PR no.: 7Y1) on Premium plus, standard on Prestige In rear bumper cover Radar monitoring system for the detection of vehicles in the area to the rear and side of the vehicle for: • Audi pre sense rear including Audi side assist • Rear cross traffic assist • Exit warning • 3C – J769 (master) • CF – J770 (slave) • Extended CAN participant • Both control modules inter-connected by a sub-bus system. The control module is integrated in the bumper cover. The system has to be calibrated after removal and installation.Address Words Data bus communication Special featureLane Change Assistance Control Module J769Lane Change Assistance Control Module 2 J770646_03631 Electronic Stability Control (ESC)Designation Equipment Installation location Tasks ABS Control Module J104 Always installed On left hand side of engine compartment Controlling: • Anti lock braking system (ABS) • Electronic Stability Control (ESC) • Traction Control System (TCS) • Electronic Differential Lock (EDL) • Torque vectoring • Multi-collision braking • Electro-mechanical parking brake (EPB) 03 FlexRay participant • The control module can be replaced separately from the valve block. ESD protective mat VAS 6613 must be used. • The electro-mechanical parking brake softward is integrated in the ABS control module. Address word 53 is no longer used for electro-mechanical parking brake.Address Word Data bus communication Special features646_037ABS Control Module J10432 Information electronicsDesignation Equipment Installation location Task Address Word Data bus communication Information Electronics Control Module 1 J794 Always installed In glove compartment Controlling the infotainment systems 5F • Infotainment CAN bus user • MOST participant • J794 is connected to the Front Information Display Control Head J685 and the Multimedia System Control Head E380 via the Modular Infotainment System (MIB) CAN. • J794 is the system manager and the ring break diagnostics master for the MOST bus. • J794 is connected to the Instrument Cluster Control Module J285 and the Front Information Display Control Head J685 via LVDS bus (image transfer for navigation display in instrument cluster or MMI display).Special featuresInformation Electronics Control Module 1 J794646_03833 Sound amplificationDesignation Equipment Installation location Task Address Word Data bus communication Digital Sound System Control Module J525 Optional equipment (PR no.: 9VS) In left hand side of luggage compartment, behind luggage compartment side trim Activation of up to 19 speakers 47 MOST participant646_040Digital Sound System Control Module J52534 Suspension controlDesignation Equipment Installation location Tasks Drivetrain Control Module J775 Standard equipment with optional Audi adaptive suspension system Under center console storage bin Wheel damping control • Reading input (senders/sensors/switches) • Level control system sensors • Activation (actuators/control elements) • Damper adjustment valves 74 FlexRay participant J775 is responsible for driving dynamics control.Address Word Data bus communication Special featureDrivetrain Control Module J775646_042Power steeringDesignation Equipment Installation location Tasks Power Steering Control Module J500 Always installed Connected to the steering gear. Controlling: • Power steering • Servotronic speed-responsive power steering • Corrective steering inputs in conjunction with Audi active lane assist, park assist, evasion assist and trailer assist • Corrective steering inputs in conjunction with ESC 44 FlexRay participant The control module and power steering motor can only be replaced together with the steering gear.Address Word Data bus communication Special featurePower Steering Control Module J500646_04335 Dynamic steering (not available at model introduction)Designation Equipment Installation location Tasks Active Steering Control Module J792 Optional equipment (PR no.: 1N8) In driver's side footwell, under the floor covering • Calculating the super-imposition angle required to implement the variable steering ratio. • Correcting the calculated super-imposition angle of the stabilizing function through ESC intervention. • Reading input (senders/sensors/switches) • Index sensor • Motor position sensor • Activation (actuators/control elements) • Dynamic steering actuator • Dynamic steering lock 1B FlexRay participant Basic setting is necessary after: • replacement by a new or different Active Steering Control Module J792 • replacement by a new or different steering column • replacement by a new or different Steering Angle Sensor G85 or recalibration • Changing the wheel alignment values • Disconnecting the actuator from the steering column or the actuator from the steering gearAddress Word Data bus communication Special features646_044Active Steering Control Module J79236 Exterior lightingHeadlight variantsTwo headlight variants are available for the 2017 Audi A4: • Xenon headlight (ECE1) and SAE2)) standard equipment on Premium models • LED headlight (ECE1) and SAE2)) standard equipment for Premium plus and Prestige models The headlights are connected to the vehicle body by adjusting elements. This makes it possible to align them precisely with the other body components. Before the headlights can be removed, the bumper cover must be removed and the headlight washer nozzle unclipped from the headlight. In the event of damage to the upper and inner headlight attachments, repair tabs can be attached to the headlight housing. The parts marked "Service" in the exploded-view illustrations of the headlights on the following pages can be replaced individually in the event of damage. For information as well as the corresponding spare part numbers, please refer to the repair literature and ETKA.Xenon headlightThe illustration shows the left headlight in the ECE1) version. The SAE version is similar.Sealing cover in headlight housing – access for changing bulb in foglight "Service"Left Headlamp Beam Adjustment Motor V48Reflectors for LED daytime running light and side lightLeft Front Turn Signal Bulb M5 "Service"Left HID Headlamp Bulb L13 "Service"Left Front Fog Lamp Bulb L22 "Service"646_0541) 2)ECE = for European market SAE = for North American RegionNote Left Front Fog Lamp Bulb L22 (for the all-weather light function) can be accessed via a cover on the back of the headlight housing and can be replaced after the headlight has been installed.37 LED headlightsLeft Headlamp Beam Adjustment Motor V48Left LED Headlamp Power Output Module 1 A31 "Service"Headlight moduleLeft Light Control Module J1018 "Service" Low beam moduleFiber optic cable for daytime running light / side light, turn signal646_05538 Xenon headlightThe illustration shows the left hand headlight in the ECE1) version. The SAE version is similar.Daytime running light/ parking light Low beam/ main beam646_057Turn signalAll weather lightLight functions Daytime running light Side light Low beam High beam All weather light Turn signal Sidemarker (SAE only )2)Type of bulb used 4 LEDs Parking light is dimmed if light function is active Gas discharge lamp D5S Changes over from low beam using shutter Bulb H8 Bulb PSY24W 1 LEDPower 5 watts25 watts35 watts 24 watts 0.5 wattsSpecial features of the light functions The daytime running lights are switched off for the duration of a turning cycle. The all-weather light is switched off during the turning signal cycle as soon as the vehicle exceeds a speed of 25 mph (40 km/h). The all-weather light in both versions is deactivated during the turn signaling cycle as soon as the vehicle exceeds a speed of 40 kph. Left and Right Low Beam Headlamp Reflector Motors V294 and V295 are used for switching between low and high beams. The LEDs for the side light function and the low beams of the gas discharge lamps are used for the Coming Home/Leaving Home function.1) 2)ECE = for European market SAE = for North American Region 39 Schematic diagram of the activation mechanismGas discharge headlight (left hand side of vehicle)Vehicle Electrical System Control Module J519 −− Voltage supply −− Activation of light functions −− Calculation/activation of headlight range adjustmentDiscrete linesConvenience CAN−− Control module −− Low beam shutter −− Fog light bulb, left −− Turn signal bulb, front left −− LEDs for parking lights and daytime running lights −− LEDs for front left side marker light (SAE2)) −− Beam-height adjustment servo motor646_058Activation Vehicle Electrical System Control Module J519 is responsible for power supply as well as for activating all bulbs in the headlight. J519 also activates the low beam shutter and the headlight range adjustment control motors. Headlight range adjustment The gas discharge headlight has automatic static headlight range adjustment. This means that changes in headlight range are compensated for when the vehicle is loaded differently. However, changes caused by rolling movements of the vehicle under acceleration and braking are not compensated. J519 receives information about ride height from either Comfort System Central Control Module J393 or, if installed, Drivetrain Control Module J775.Service The basic setting of the headlight range adjustment function is configured by J519. The foglamp bulb can be replaced with the headlights installed. This bulb can be accessed via a cover on the back of the headlight housing. The headlight must be removed in order to replace the gas discharge lamp or the turn signal lamp. Optional equipment The xenon headlight can be combined with main beam assist (PR no.: 8G1).1) 2)ECE = for European market SAE = for North American Region40 LED headlightThe figure shows the left hand headlight in the ECE1) version.Daytime light/ side light/ turn signal High beam Low beam646_059Daytime running light/ parking lightTurning light/ all-weather light/ static cornering lightDaytime running light/ parking lightLight functions Daytime running light Side light Low beam High beam All weather light Turning light Static cornering light Turn signal Sidemarker (SAE only2))Type of bulb used 7 LEDs with plastic optical fibers Parking light is dimmed if light function is active 11 LEDs 6 LEDs 3 LEDs 0 - 25 mph (0 - 40 km/h), turn signal responsive 0 - 43 mph (0 - 70 km/h), steering angle responsive 8 LEDs 1 LEDPower 18 watts20 watts 20 watts 10 watts18 watts 0.5 wattsSpecial features of the light functions The "upper" daytime running light is dimmed for the duration of the turn signaling cycle. The "lower" daytime running light is dimmed to side light level. The all-weather light is not affected by turn signal operation. The LEDs for the side light function and the low beam function are used for the Coming Home / Leaving Home function.1) 2)ECE = for European market SAE = for North American Region 41 Schematic diagram of the activation mechanismExternal terminal 15 supplyVehicle Electrical System Control Module J519Voltage supplyDiscrete lineLED headlights (left hand side of vehicle)Left LED Headlamp Power Output Module 1 A31 −− LEDs for left low beam headlight −− LEDs for left low beam headlight −− LEDs for left static cornering lightVoltage supplySub-bus system−− Activation of light functions −− Calculation/activation of headlight range adjustmentConvenience CANLeft Light Control Module J1018 Discrete lines −− LED for left side marker light (SAE2)) −− Left headlight range control motorDiscrete lines Left Daytime Running Lamp And Position Lamp LED Module L176 −− LEDs for parking lights and daytime running lights −− LEDs for left turn signal646_060Activation Vehicle Electrical System Control Module J519 supplies voltage to Left and Right Led Headlamp Power Output Modules 1 A31/A27 and to Left and Right Light Control Module Control Modules J1018 and J1023. J519 communicates with these modules over a sub bus system. A31 and A27 are responsible for activating the LEDs for low beams, high beams and the static cornering light (turning light). These modules have diagnostic capability and can be accessed through Address Words D6 and D7. J1018 and J1023 are responsible for the parking lights/ DRLs, turn signals, side marker lights and the headlight range adjustment servo-motors. They have diagnostic capability and can be accessed through Address Words 29 and 39. Headlight range adjustment The LED headlight has automatic dynamic headlight range adjustment. Changes in the range of the headlight beam due to loading of the vehicle as well as braking and accelerating are compensated. J519 receives information on ride height from either Comfort System Central Control Module J393 or Drivetrain Control Module J775 if installed.Service The basic setting of the headlight range adjustment function is configured in Vehicle Electrical System Control Module J519. LED headlight bulbs cannot be replaced. Only the outer units can be replaced individually after removing the headlights. Optional equipment The LED headlight can be combined with main beam assist (PR no.: 8G1).1) 2)ECE = for European market SAE = for North American Region42 Tail lightsThe A4 tail lights are mounted in both the fender and the rear trunk lid. They are activated by Comfort System Central Control Module J393.LED tail light (PR no.: 8SP)The figure shows the left hand tail light for the A4 sedan model in the SAE2) version.Brake light/ turn signal Brake light/ turn signal Tail light646_073Tail light/ sidemarkerTail lightBrake lightBack-up lightRear fog lightLight functionsSedan2) Bulb/lamp Power 10 watts 10 watts 6 watts 8 watts 6 watts 4 watts 4 wattsBrake light/turn signal (dynamic)3) Tail light3) Brake light3) Turn signal (dynamic)4) Back-up light Tail light4) Rear fog light4), 5)4)12 LEDs 33 LEDs 6 LEDs 18 LEDs 4 LEDs 15 LEDs 2 LEDsSpecial features of the light functions The tail lights are also activated if the vehicle is equipped with a Coming Home / Leaving Home function. Light functions are not deactivated when the rear trunk lid is open. If the tail light is activated and the brake light is simultaneously active, the LEDs for the brake light/turn signal in the rear trunk lid are deactivated. If the tail light is activated and the turn signal is simultaneously active, the LEDs for the brake light/turn signal in the rear trunk lid are also active. Amber-colored LEDs are used for the turn signal. With the dynamic turn signal function, the LEDs for the turn signal/brake light are briefly activated in a dimmed manner when the turn signals are activated. After that, the LEDs for the turn signal function are dynamically activated in an alternating sequence to produce the dynamic effect. Service No bulbs/lamps can be replaced in the LED tail lights. In the event of a fault, the complete assembly must be replaced.4) 5)2) 3) AE = for North American Region S Lights in the body side panelsLights in the rear lid One side only  43 High-mounted brake light / license plate lightsActivationBoth the high-mounted brake light and license plate lights are activated by Comfort System Central Control Module J393. They remain active even when the rear trunk lid is open.High-mounted brake lightThe high-mounted brake light is installed inside the vehicle behind the rear window. It has 18 LEDs with a power output of 4 watts. In the event of failure, the entire assembly must be replaced.646_075High-Mounted Brake Lamp Bulb M25License plate lightsThe license plate lights on the Audi A4 use LED technology. Each of the license plate lights is clipped into the luggage compartment lid and has two LEDs.44646_077 Interior lightingTwo levels of interior lighting are used on the 2017 Audi A4. • QQ1 lighting package - standard equipment on Premium and Premium plus models. • QQ2 background lighting - standard equipment on Prestige models QQ1 Vanity lights, footwell lights, cupholder light, center console background lighting, entry light, door panel lighting in the door trims and door inner handle lighting. White light and LED technology are exclusively used as light sources. QQ2 Contour lighting in the door trim, door pocket lighting. The LEDs are colored. 30 light colors are available. The door pocket lighting in the Audi A4 (type 8W) is non-capacitive. An exception is the LED in the door inner handle which lights up in white only. The list of interior lighting features with the various production numbers always includes the equipment with lower production numbers. The background lighting QQ2 is controlled by a background lighting module. The background lighting module is a software function and is integrated in Vehicle Electrical System Control Module J519. J519 is the RGB master. RGB denotes the colors red, green and blue. The color profiles are produced by additive mixing of these colors. In the case of additive color mixing, the human eye is able to discern multiple wavelengths simultaneously and in quick succession, but the different colors cannot be resolved and appear as a single color to the eye.Apron lightingThe apron lighting is provided by 2 LEDs per door. These LEDs also function as door handle lights.646_00445 Interior door trim lightingBackground lighting as shown using the door trims as an example – the door warning light may use a conventional bulb/lamp depending on country. The apron lighting is integrated in all four door handles in conjunction with PR nos. QQ1 and QQ2. Unlike the Audi Q7, the door pocket lighting is not capacitively controlled.Front door trimDoor panel lighting Inner door handle light Contour lightingDoor warning light (passive)Exit warning (with optional assistance system)646_005Door pocket lightingEntry lightSpeaker lightingRear door trimDoor panel lighting Inner door handle light Contour lightingDoor warning light646_00646Door pocket lightingEntry light Function and control Interior and background lightingThe LEDs of the interior and background lighting are controlled by various control modules and are networked with one another via the Convenience CAN. These are: • • • • Vehicle Electrical System Control Module J519. Comfort System Central Control Module J393. Driver Door Control Module J386. Front Passenger Door Control Module J387. The following control modules connected by LIN bus are also used: • Driver Side Rear Door Control Module J926. • Passenger Side Rear Door Control Module J927. • Roof Electronics Control Module J528. • Front Roof Module WX3. • Rear Interior LampWX2.WX2Rear left reading lightRear right reading lightWX3Front left reading lightJ528Front right reading lightLIN 2Vanity light, left/ right Glove boxFront footwell lightRear footwell lightJ519Storage compartment Apron lightingApron lightingDoor warning light1) Entry lightDoor warning light1) Entry lightInner door handleJ386 Convenience CANJ387Inner door handleSpeakerSpeakerLIN2)LIN2)Door warning light1) Entry lightDoor warning light1) Entry lightInner door handleJ926J393J927Inner door handleApron lightingApron lighting646_007Luggage compartment1) 2)Country-dependent Door control module LIN bus 47 RGB componentsThe RGB components of the background lighting are controlled by Vehicle Electrical System Control Module J519. The individual LEDs or optical fibers are supplied via 2 LIN bus lines.J519LIN 6LIN 5Footwell Door shoulderCupholderFootwell Door shoulderSpeakerSpeakerCenter console Door pocket Door pocketDoor shoulderDoor shoulderSpeakerSpeakerDoor pocketDoor pocketFootwellFootwell646_00848 Overhead moduleThe overhead module is used to activate and read in the following components: • • • • • • Roof Electronics Control ModuleJ528. Sliding sunroof operating button. Garage Door Opener Control Head E284. Front interior lights. Hands-free telephone microphone. Front Passenger Airbag -Disabled- Indicator Lamp K145. The interior lights are capacitive. The interior lights use LED technology. J528 is a LIN participant of J519.Sliding sunroof operating buttonMicrophoneMotion detectors of the interior monitoring system integrated in the anti-theft alarmGarage Door Opener Control Head E284Microphone646_009Interior lightInterior lightFront Passenger Airbag -Disabled- Indicator Lamp K14549 Audi drive selectFunctional characteristicsThe Audi A4 is equipped with Audi drive select. With Audi drive select, it is possible to modify the vehicle characteristic. The mode can be changed when the car is stationary with the ignition switched on or while driving. In the Audi A4, the driver can select between the following drive modes: • • • • comfort. auto. dynamic. individual. Audi drive select affects the following equipment: • • • • • • • • • • • Automatic transmission. Sport differential (not available at vehicle introduction). Climate control system. Cornering light. Ambient lighting. Dynamic steering (not available at vehicle introduction). Damper control. Cruise control system. Distance regulation. Audi pre sense basic / pre sense city. Start-stop system.Displays and operationAudi drive select can be configured using Control Unit 1 for Driving And Convenience Functions E791 or Multimedia System Control Head E380. Depending on the vehicle equipment specification, the drive mode can also be selected on the multifunction steering wheel. When using the multi-function steering wheel, the options menu is displayed on the MMI screen or in the instrument cluster.646_078Control Unit 1 for Driving And Convenience Functions E791Multimedia System Control Head E380646_07950 Audi drive select functionThe following systems are influenced by Audi drive select:System Engine and automatic transmission SteeringVehicle characteristic Depending on mode, the engine and automatic transmission react to accelerator inputs in a more spontaneous or more balanced way. In the sporty dynamic mode, the gear shift points are adjusted to higher in the RPM band. The steering can be adapted with the regard to steering assistance. A distinction is made here between three characteristics ranging from comfortable (comfort) and balanced (auto) to sporty (dynamic). The following applies to models with dynamic steering: To minimize steering effort for the driver, the steering ratio is adjusted to the speed at which the vehicle is traveling. At higher speeds, the steering is configured for less sensitivity in order to improve handling. At lower speeds, the steering is more direct in order to minimize steering effort for the driver during maneuvering, for example. In addition, the dynamic steering system provides a more agile steering response at low and medium speeds. Audi drive select allows the damper control system to be configured for sporty (dynamic), comfort-oriented (comfort) or balanced (auto) response. Depending on drive select mode, the acceleration response options range from comfortable (comfort) to sporty (dynamic). Accord