TECHNICAL DOCUMENTATION

SSP 990143 – The 2015 Audi A3 Introduction

PDFEN92 pages7 MB
SSP 990143 – The 2015 Audi A3 Introduction - PDF cover

This PDF is currently unavailable.

Read document text
eSelf Study Program 990143The 2015 Audi A3 Introduction Audi of America, LLC Service Training Created in the U.S.A. Created 11/2013 Course Number 990143 ©2013 Audi of America, LLC All rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC. Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.Revision 4: 12/20133 ContentsIntroduction.................................................................................................6 The A3 sedan body.......................................................................................7Dimensions ............................................................................................................................................................... 7 Vehicle architecture (MQB) ...................................................................................................................................... 9 MQB and the Audi A3 .............................................................................................................................................. 9 Materials - ultra lightweight construction .......................................................................................................... 11 Body panels ............................................................................................................................................................ 13 Joining techniques ................................................................................................................................................. 13 Panorama tilt sunroof ........................................................................................................................................... 16 Bumper system ...................................................................................................................................................... 18 Underbody .............................................................................................................................................................. 18Passive safety.............................................................................................19Components ........................................................................................................................................................... 19 System overview .................................................................................................................................................... 20 Vehicle Airbags ....................................................................................................................................................... 21 Front safety belt tensioner ................................................................................................................................... 26 Pelvic belt tensioner with locking buckle ............................................................................................................ 27Active Safety...............................................................................................31Audi pre sense ........................................................................................................................................................ 31Engines.......................................................................................................371.8L and 2.0L TFSI engines ................................................................................................................................... 37 Diesel engines ........................................................................................................................................................ 39 Engine/transmission combinations ..................................................................................................................... 41Power transmission....................................................................................43Overview ................................................................................................................................................................. 43 5th generation Haldex coupling ........................................................................................................................... 45 Transmission selector mechanism ....................................................................................................................... 52Fuel tanks...................................................................................................53Exhaust system ...................................................................................................................................................... 54Running gear..............................................................................................55Design concept ....................................................................................................................................................... 55 Suspension variations ........................................................................................................................................... 57 Tire Pressure Monitoring System ......................................................................................................................... 57 Wheels and tires .................................................................................................................................................... 58Electrical system........................................................................................59Audi drive select ..................................................................................................................................................... 59 Installation locations of control modules ........................................................................................................... 61 Topology ................................................................................................................................................................. 63Climate control...........................................................................................65Introduction ........................................................................................................................................................... 65 Connected components ........................................................................................................................................ 67 Connected components ........................................................................................................................................ 68Infotainment..............................................................................................69Overview of versions .............................................................................................................................................. 69 Standard MIB ......................................................................................................................................................... 72 High spec MIB with navigation ............................................................................................................................. 73 Multimedia System Control Head E380 ............................................................................................................... 75 MMI display ............................................................................................................................................................ 764 ContentsAudi Connect..............................................................................................77Overview ................................................................................................................................................................. 77 LTE ........................................................................................................................................................................... 78 Antenna overview .................................................................................................................................................. 81 LTE antennas .......................................................................................................................................................... 83 Sound systems ....................................................................................................................................................... 85Service........................................................................................................87Service interval overview for North American region ......................................................................................... 87 Special tools and workshop equipment .............................................................................................................. 88Self Study Program....................................................................................91 Knowledge Assessment.............................................................................92This eSSP contains video links which you can use to access interactive media.This eSelf Study Program teaches a basic knowledge of the design and functions of new models, new automotive components or technologies. It is not a Repair Manual! All values given are intended as a guideline only. For maintenance and repair work, always refer to the current technical literature.NoteReference5 IntroductionThe Audi A3 can look back on a 16-year success story. The first generation of the series, which debuted in 1996 as a three door, established an entirely new market segment – the premium compact class. In 1999 the five-door hatchback and the sporty Audi S3 completed the family. In total, around 990,000 vehicles were sold. The second generation, launched in 2003, was even more successful, achieving sales of approximately 1.8 million vehicles. With the newest generation of the A3, the Group has set itself the goal of improving the fuel economy of its internal combustion engines, extending its product range to include alternative drive systems such as natural gas engines and electric motors, and equipping the vehicles with the latest technical innovations. The basis for implementing these objectives is the MQB or “modular transverse platform”, a standardized architecture in which various vehicle components can be combined in any configuration on modular principles. This broadens the diversity of the model range, resulting in more efficient production, engines and combinations of materials. The 2015 A3 sedan represents the cumulative technological expertise of Audi in a compact format. In its lightweight body, its interior architecture and its user interfaces, the A3 sedan will once again set standards in its class. Its engines impress with their efficiency and power, and the range of driver assistance systems and infotainment solutions is unparalleled in the premium compact class. The lightweight body and newly developed engines have had major consequential effects throughout the vehicle, reducing the weight of many suspension, exhaust and interior components. At launch, the vehicle will be offered with two recently refined engines from the EA888 family. The Modular Infotainment Platform (MIB) makes its debut in the A3 sedan. It represents a big step forward in mobile communication electronics. The A3 also sets new standards in the premium compact class when it comes to driver assistance systems. One of the most important of these is Audi pre sense. In the event of an impending collision, the system warns the driver in progressive stages and, if necessary, can initiate partial braking in order to reduce the car’s speed at impact. The Audi A3 and S3 sedans are assembled in Györ, Hungary. The site in northwestern Hungary is one of the largest automobile factories in the world. This is where Audi has assembled the TT coupe, and in the near future will assemble the A3 cabriolet. It is an ultra modern facility with the capability of complete production work—from stamping to final assembly.625_0016 The A3 sedan bodyDimensions55.7 in (1416 mm)37.0 in (942 mm)61.2 in (1555 mm) 70.7 in (1796 mm)625_03660.0 in (1526 mm) 77.1 in (1960 mm)625_037m)6m(10 06 in39.36.3 (924 mm)34.2 in (869 mm)103.8 in (2637 mm) 175.4 in (4456 mm)37.4 in (950 mm)625_038727.0 in (688 mm) 57.2 in (1453 mm)54.8 in (1392 mm)56.0 in (1423 mm)52.9 in (1345 mm)39.3 in (1000 mm)37.4 in (951 mm)625_039Dimensions and weight Length Width Height Front track width Rear track width Wheelbase 175.4 in (4456 mm) 70.7 in (1796 mm) 55.7 in (1416 mm) 61.2 in (1555 mm) 60.0 in (1526 mm) 103.8 in (2637 mm) Front elbow room Rear elbow room Front head room Rear head room Load pass-through width Load lift-over height Luggage compartment volume Curb weight (approximate) Permissible total vehicle weight1)57.2 in (1453 mm) 56.0 in (1423 mm) 39.6 in (1006 mm) 36.3 (924 mm) 39.3 in (1000 mm) 27.0 in (688 mm) 15.0/31 1) cu ft (425/880 1) l)2899.0 lb (1325 kg) 4111.6 (1865 kg)Rear seat foldedA3 sedan compared to A4 sedan8 Vehicle architecture (MQB)The Audi A3 sedan builds on the body structure of the three-door A3. It is part of the MQB strategy used by the Volkswagen Group of which Audi is a part. MQB stands for modular transverse baukasten or modular transverse platform. It is not so much a platform per-se, but rather a system for introducing commonality across disparate platforms that share the same engine orientation — regardless of model,Wheelbase + 1.37 in (35 mm)vehicle size or brand. MQB uses a core group of components across a wide variety of platforms — for example, sharing a common engine-mounting for all drivetrains. The concept allows diverse models, including those from the company‘s various brands, to be manufactured at the same plant, further saving cost.VariableUniformVariableLonger overhang + 6.4 in (165 mm)MQB and the Audi A3The underbody of the A3 series consists of 3 modules:625_118• • • the front section Floor pan, center section Trunk floorCompared to the three-door A3, the A3 sedan needed a longer central floor pan and a longer rear floor pan but are based on the same basic design and manufacturing processes.625_1199 Notes10 Materials - ultra lightweight constructionBody developers at Audi have broad-based engineering expertise spanning all relevant materials. This know-how is not limited to just a specific material, rather the motto is: “The right material at the right place for optimal function.” The multi-material body of the Audi A3 lives up to this maxim. All the ultra lightweight design principles that have made all A3 models lighter than their predecessors have been applied to the design of the new A3 sedan. At the same time, the A3 sedan meets the highest demands in the area of vehicle safety. The basis for this is that only materials used are those that meet the high quality standards of Audi.Ultra high-strength hot-formed steel componentsUltra high-strength hot-formed steel components provide approximately a 24% share of the A3 sedan body structure. Before the components are stamped, special steel is heated to nearly 1832 °F (1000 °C) in a continuous oven. After heating, it is immediately placed in a water cooled press tool. The steel is quickly cooled to approximately 392 °F (200 °C) before it is stamped. The rapid cooling of the steel changes its iron/carbon structure and creates a steel with high tensile strength which in turn allows thinner wall thicknesses for the particular components. Steels created in this manner require special care and procedures during repairs.11 High-strength steel 30%Ultra high-strength hotformed steel 24%Soft steel 28.5% Modern high-strength steel 17% Aluminum 0.5%625_110625_109Ultra high-strengthA3 sedan B pillarThe B-pillar with striker plate is partially tempered during the forming process. The component assembly is very hard at the top end and softer below a narrow transition zone. This enables side impact forces to be absorbed effectively.High-strength Ultra high-strength625_11112 Body panelsSome inner and outer body panels such as the fenders, doors, rear bumper, cross member, and the rear trunk lid are all made from light steel. The following components are made from aluminum:• • • the front bumper cross member the hood the rear hat shelfThe use of both light steel and aluminum further helps reduce the weight of the body.Joining techniquesBoth old and new body component joining techniques are in use. In addition to the 4803 classic resistance spot welds used during assembly of the body, the following joining methods are also used: In each A3 sedan there are over 196 ft (60 m) of glued joints. The joint between the body side wall and roof is laser welded and then smoothed by brushes to produce a nearly invisible zero joint. The water drainage paths in the area of the rear trunk lid are joined by Plasmatron welding. To save more weight, doors and window frames are pressed in one piece. The inner and outer doors are welded by the ultra-modern remote laser technique.13• • • • MAG welding Laser welding Clinching (attachments only) Solid punch riveting 625_112Key: Ultra high-strength hot-formed steel Modern high-strength steel High-strength steel Soft steel Sheet aluminum Aluminum profile14 Ultra high strength hot-formed steel components are installed in the following areasForming the backbone of the occupant cell is what are known as form-hardened steels. An extreme temperature change during forming process gives these steels extremely high strength; the parts can be designed with relatively thin walls, making them lightweight. Form-hardened steels represent a 24 percent share of body materials. They are used in the transition from the front of the vehicle to the occupant cell, in the A-pillars, B-pillars, roof arch, center tunnel, side sills and floor panels. Altogether, they lower the car’s weight yet provide excellent strength.9 4 5 6 1 2 810 1173625_1141 2 3 4 5 6 Long members (2 left / 2 right) Upper foot room crossmember Lower foot room crossmember Left and right inner A pillars Left and right inner rocker panels Center tunnel7 8 9 10 11 Rear seat crossmember Rear transverse crossmember Left and right upper A pillars Left and right rear long members Left and right inner B pillars15 Panorama tilt sunroofThe 2015 A3 sedan features an optional panorama slide/ tilt sunroof. The roof opening is larger than that of an internally guided sunroof and creates a particularly airy and spacious interior feel for the occupants.609_069bThermal insulationThe glass roof panel is tinted and provides additional thermal insulation. Thermal insulation is provided by the following reflective components: The panorama slide/tilt sunroof module meets the statutory requirements for anti-pinch protection.• • • 99 % UV radiation reflection 92 % heat radiation reflection 90 % light radiation reflection609_08316 Roof installationThe panorama slide/tilt sunroof is glued into the roof opening and thus is a major factor contributing to body rigidity.Transverse bonded seam609_122b609_070Bonded ring seamComponent overviewGlass panelSlide/tilt mechanismWind deflectorFront trim (plastic)Cover for sliding sunroof motor/ roll-up sun-blindSliding sunroof frame (plastic) Roll-up sunblindSliding sunroof motorLifting arm guide frame609_07117 Bumper systemFront bumperCharacteristic elements of the vehicle's front end are the one-piece bumper cover and single-frame radiator grille. Large air intakes are located at the lower front.Shock absorberACC radar sensor Impact absorber Bumper cover locking element Radiator grille Front bumper cover609_072UnderbodyThe Audi A3 has a highly effective acoustic and aerodynamic underbody designed to withstand mechanical and thermal stresses. In addition to aerodynamics, attention was paid to sound absorption, body protection and thermal engine management during the development phase. The result is improved airflow around the engine and transmission capsule, the cross-members and the wheel arches, thus allowing a low drag coefficient (cw) of 0.31 to be achieved.609_08218 Passive safetyComponentsThe passive occupant protection system has the following components:• • • • • • • • • • • • Airbag control module Driver and passenger airbags Front side airbags SIDEGUARD® head airbags Driver and passenger side knee airbag Front airbag crash sensor Crash sensors for side impact detection in the doors Crash sensors for side impact detection in the C pillars Front inertia reel seat belts with electric and pyrotechnic belt tensioners Safety belt warning for all seats Safety belt switches on all seats in the seat belt buckles Safety occupancy sensor in front passenger seat625_050Optional equipment• Rear passenger side impact airbagsKey to illustration on page 20:E24 E25 E258 E259 E609 G452 G179 G180 G256 Driver Seat Belt Switch Front Passenger Seat Belt Switch Driver Side Rear Seat Belt Switch Passenger Side Rear Seat Belt Switch Center Rear Seat Belt Switch Front Passenger Seat Occupant Sensor Driver Side Airbag Crash Sensor Front Passenger Side Airbag Crash Sensor Driver Side Rear Side Airbag Crash Sensor K19 Seat Belt Indicator Lamp K75 Seat Belt Indicator Lamp K145 Front Passenger Airbag Disabled Indicator Lamp N95 Driver Airbag Igniter N131 Front Passenger Airbag Igniter 1 N132 Front Passenger Airbag Igniter 2 N153 Driver Seat Belt Tensioner Igniter 1 N154 Front Passenger Seat Belt Tensioner Igniter 1 N199 Driver Thorax Airbag Igniter N200 Front Passenger Thorax Airbag Igniter N201 Driver Side Rear Thorax Airbag Igniter N202 Passenger Side Rear Thorax Airbag Igniter N251 Driver Head Curtain Airbag Igniter N252 Front Passenger Head Curtain Airbag Igniter N295 Driver Knee Airbag Igniter N296 Front Passenger Knee Airbag Igniter N297 Driver’s Seatbelt Tensioner Igniter 2 N298 Front Passenger Seatbelt Tensioner Igniter 2 T16 Data Link ConnectorG257 Passenger Side Rear Side Airbag Crash Sensor G283 Driver Front Airbag Crash Sensor G284 Passenger Side Front Airbag Crash Sensor G551 Driver Belt Force Limiter G552 Front Passenger Belt Force Limiter G553 Driver Seat Position Sensor G554 Passenger Seat Position Sensor J234 J285 J533 J854 J855 Airbag Control Module Instrument Cluster Control Module Data Bus On-Board Diagnostic Interface Left Front Seat Belt Tensioner Control Module Right Front Seat Belt Tensioner Control Module19 System overviewG452625_051bxLegend: Powertrain CAN bus Convenience CAN bus Diagnosis CAN bus Input signal Output signal20 Vehicle AirbagsPassenger front airbagThe 2015 A3 sedan for the North American market will come equipped with a two-stage adaptive hybrid gas generator front passenger airbag.625_050Based on accident parameters, Airbag Control Module J234 determines the time interval at which Front Passenger Airbag Igniter 2 N132 is activated after Front Passenger Airbag Igniter 1 N131.Front Passenger Airbag Igniter 1 N131Front Passenger Airbag Igniter 2 N132Gas generatorHousing625_12521 New generation of connectorsA new locking style connector is used on front passenger airbag that incorporates a ground wire connected to the vehicle body. The ground circuit provides protection from electro-static discharge. The connector has been mechanically encoded so it can only be installed in one way.CoverLocking elementContactMechanically encoded housing625_124Driver and passenger knee airbagsThe Audi A3 sedan is equipped with both driver and passenger knee air bags. Both airbags use tubular hybrid gas generators.Driver Knee Airbag625_122Passenger Knee AirbagFront Passenger Knee Airbag Igniter N296Knee airbag22 Driver Front Airbag Crash Sensor G283 Passenger Side Front Airbag Crash Sensor G284The A3 sedan for the North American region uses two up-front sensors for detection of front and/or rear collisions. They work in conjunction with Airbag Control Module J234. These sensors are accelerometers that measure the acceleration, deceleration and longitudinal direction of the vehicle.G284G283625_05223 Front Passenger Seat Occupant Sensor G452 Passenger Occupant Detection System Control Module J706The task of the seat occupancy detection system is to determine the following: 1. If the seat is occupied by a child or if a rearward facing child seat is installed. 2. If an adult is seated. Passenger Occupant Detection Control Module J706 evaluates the signals from Front Passenger Seat Occupant Sensor G452. If J706 recognizes an empty passenger seat or that a rearward facing child seat is installed, it instructs Airbag Control Module J234 to disable the passenger front airbag and knee airbag. This means that in the event of a collision, neither the passenger front airbag nor front passenger knee airbag would deploy. Front passenger Airbag -disabled- Indicator Lamp K145 in the instrument panel warns the driver of the status of the passenger airbag and knee airbag. If Airbag Control Module J234 has disabled these airbags based on the signals from J706, warning lamp K145 will remain illuminated. In addition to the warning lamp, Airbag Control Module J234 will also issue an optical and acoustic warning if the seat is unoccupied or if a safety belt has been unbuckled. Detection of an unbuckled belt is determined by a signal from Front Passenger Seat Belt Switch E25.Front Passenger Seat Occupant Sensor G452ElectrodeDielectric materialElectrodeG452 is a capacitor-type sensor. A capacitor is made of two plates (electrodes) and an insulator (dielectric), sandwiched between them. When voltage is applied to one of the electrodes and the other electrode is connected to the battery‘s negative terminal, the capacitor begins to accumulate energy. The capacitance of a capacitor can be altered by varying the size of the electrode plate or the dielectric.625_058Function With this type of occupant detection system, the vehicle body and sensor G452 represent the two plates of the capacitor. These components obviously do not change in size. The dielectric consists of the upholstery, the atmosphere, the adjoining seat trim parts and the occupant. The capacitance will change due to the liquid content of the occupant‘s body compared to when the seat is unoccupied or if a rear facing child seat is installed. This capacitance signal data is interpreted by Passenger Occupant Detection System Control Module J706 to determine if the seat is occupied or not.Front Passenger Seat Occupant Sensor G452 Passenger Occupant Detection System Control Module J706625_05924 Installation locationG452 is installed under the seat cover but on top of the seat heater elements.Seat foamFront Passenger Seat Occupant Sensor G452Passenger Occupant Detection System Control Module J706In principle, J706 measures the capacitance of Front Passenger Seat Occupant Sensor G452. The values from J128 are read cyclically by J706 and transferred to Airbag Control Module J234 via a LIN bus.625_060DiagnosisJ706 is connected to G452 via a coaxial cable and is supplied assembled to the factory as a unit. The coaxial cable and the plug of the coaxial cable must not be repaired. There are different seat variations and thus different controls module variations for J706. The software in the ECU is matched to the respective seat. Control module J706 and sensor G452 cannot be replaced separately. They are matched during production. If they are replaced, a Basic setting must be performed with the Scan Tool. During this basic setting the serial number of the installed components are entered into the Airbag Control Module.Serviceable componentsPassenger Occupant Detection System Control Module J706Coaxial cable625_061Front Passenger Seat Occupant Sensor G452Reference Please refer to the latest repair and parts information when replacing the seat sensor and control module.25 Side airbag crash sensorsThe side airbag crash sensors for the driver and passenger sides (G179 and G180) are capacitive pressure sensors. The pressure sensors have a new mounting concept and are no longer bolted to the inner door panel The pressure sensors are inserted into the inner door panels and then secured into place by twisting.Retaining lugsConnector housingGasketTurning aid625_146Front safety belt tensionerIn combination with Audi pre sense basic, the 2015 Audi A3 is equipped with reversible safety belt tensioners driven by electric motors. This is in addition to the pyrotechnic belt tensioners. Airbag Control Module J234 operates Left and Right Seat Belt Tensioner Control Modules J854 and J855 as LIN modules. When Audi pre sense basic detects specific driving situations, signals are sent to the data bus. The airbag control module evaluates the signals and, if necessary, instructs the seat belt tensioner control module to partially or fully tension the safety belts via an electric motor. For further information on Audi pre sense, refer to the chapter on Active safety, page 31. The automatic safety belt retractors use rack-type pyrotechnic belt tensioners. If an automatic seat belt retractor with seat belt tensioner control module is replaced, the basic setting procedure must be performed using the “Guided Fault Finding“ function.Safety belt tensioner control moduleReversible tensioner with electric motorActive belt force limiterPyrotechnic safety belt tensioner625_08626 Pelvic belt tensioner with locking buckleDepending on the country version, the 2015 A3 sedan can be equipped pyrotechnic tensioning safety belts that help to reduce injury to the pelvic area during certain types of collisions. The safety belts are deployed by Driver Seat Belt Tensioner Igniter 2 N297, and Front Passenger Seat Belt Tensioner Igniter 2 N298. Vehicles with this style safety belts will also have a new locking-type buckle. In certain types of accidents, the pelvic belt tensioners, in conjunction with the new locking buckle, help protect the occupant in the following manner:Lock buckle• • • • To help separate the pelvic force from the thoracic force To help reduce the chest deflection force To help limit the movement of the pelvis To help improve the contact between the pelvis and seatAutomatic safety belt retractorSafety belt guide piece Belt tensionerCoupling625_062Operation during an accidentWhen Airbag Control Module J234 determines the criteria for an accident severe enough to deploy the pyrotechnic safety belts has been exceeded, the shoulder portion of the safety belt is tensioned from the clamping point of the locking buckle in the direction of the belt tensioner by the pyrotechnic devices in the automatic safety belt retractor. At the same time, N297 and N298 are triggered and the lap portion of the safety belt is tensioned by the movement of a steel cable attached to the safety belt.625_06327 Pelvic belt tensionerConstruction The pelvic belt tensioner consists of the following parts:Balls They are in constant contact with the pressure chamber tube.Piston with ball retainerSteel CableRope seal (Seals the steel cable from the pressure chamber)Pressure chamber tubeCoupling (connects pelvic tensioner to lap portion of the safety belt)Pressure chamber sealwire with connector625_069Polytechnic propellant chargeLocking cone (Fixed to the seat cable)Function - Ignition and Pelvic belt tensioning When a signal from Airbag Control Module J234 ignites the pyrotechnic pelvic belt tensioner propellant there is a sudden increase in the pressure chamber. The sudden increase in pressure propels the piston, balls and locking cone and steel cable forward.625_070Function - Locking Because the steel cable is connected to the lap portion of the safety belt, the belt is tightened by approximately 4.0 in (100 mm) when the igniter is triggered. The locking buckle acts as a load fixing point and anchors the lap portion of the safety belt at the buckle. When the cable has reached its limit, there is a small reactive backward movement. This forces the balls to move against the cone shape of the piston and deform the inner tube of the pressure chamber. This prevents cable from returning and holds the safety belt firmly against the occupant’s lap.deformation of the pipemax. 100 mm625_07128 Installation locationThe pelvic belt tensioner is located by tabs and then bolted into place along the lower inner front door sill.tab connection in sill625_072Coupling point The end of the lap portion of the safety belt is routed through a guide piece and stitched to a joining piece of the pelvic belt tensioner assembly. A foam piece covers the joined pieces to prevent noise.Point where safety belt is stitched to pelvic belt tensioner Foam pieceGuide pieceSteel cable, lap belt tensioner Joining point of safety belt and pelvic belt tensioner.625_064Locking buckleA newly designed safety belt buckle is used. The lock buckle prevents movement and forms a separate load path for the shoulder and lap portion of safety belt in the event of an accident.625_065Note The Pelvic belt tensioner is a pyrotechnic device. Always follow all safety Warnings and Cautions as outlined in the repair literature when working on or near these components.29 Design and operation The locking buckle has a movable spring loaded piece that allows the safety belt to move freely under normal operating conditions. During an accident in which the Pelvic belt tensioner has be triggered, the locking piece is displaced and blocks the safety belt from moving.CoverSeat Beltlocking piece with springLock buckle625_066Function Not blocked BlockedLocking pieceSeat beltLock buckle625_067 625_068Reference For information on removing and installing the lap belt tensioner please refer to the current repair literature and Guided Fault Finding using the VAS Scan Tool.30 Active SafetyAudi pre senseAudi pre sense is able to detect critical driving situations, and initiate measures to prepare the vehicle and occupants for an impending collision. This is made possible by networking various in-vehicle systems. The systems send data continuously to the data bus. Other control modules are able to evaluate this information and take appropriate action. Please note that Audi pre sense cannot prevent collisions. It serves only to assist the driver and potentially reduce the severity of the collision.Audi pre sense basicLongitudinal dynamics function When vehicle is moving forward at a speed greater than 18.6 mph (30 km/h) and the driver executes a “hazard braking maneuver” in which the brake pressure reaches a defined level, the reversible safety belt tensioners are partially tensioned. If the ESP is set to “Sport” or “OFF” using either ASR/ESP Button E256, Driving Profile Selection Switch Module E592 or if the Audi drive select is set to “dynamic” via the MMI, the safety belts will not be partially tensioned.Drive profile selection switch module E592ASR/ESP Button E256609_075609_076aEmergency braking function During an “emergency braking” maneuver in which the brake pressure exceeds a defined value for a defined period of time, the reversible safety belt tensioners are fully tensioned by the electric motors. In this scenario, Airbag Control Module J234 evaluates the signals sent on the data bus from ABS/ESP Control Module J104. J234 then instructs Seat Belt Tensioner Control Modules J854 and J855 to fully tension the safety belts. Depending on the situation, J104 can also activate the hazard warning flashers.31 Transverse dynamics function If the vehicle oversteers or understeers, the ESP system tries to stabilize it. If the vehicle becomes unstable because certain physical limits have been exceeded, Airbag Control Module J324 initiates a partial tensioning of the electrically reversible safety belt tensioners. If the vehicle can no longer be stabilized, the safety belt tensioners are fully tensioned. At the same time, the side windows and the tilt/slide sunroof (if installed) begin to close.Crash function in the low speed range If the Airbag Control Module J234 detects a head-on collision with low vehicle deceleration (no airbag deployment), it decides whether or not to fully tension the safety belts based on a situation-specific control module algorithm. It does not take any other precautions, such as turning on the hazard warning flashers, or closing a window or sunroof. System characteristics of Audi pre sense basic:• If a safety belt is not being worn or if the passenger• If ESP is set to "Sport" or "Off" or if Audi drive select isairbag is set to "Off", the reversible safety belt tensioner is not activated.set to "dynamic", the safety belts are not partially tensioned.• The belt tensioner control modules (J854 and J855• If ESP is set to "Sport" mode or "Off", the safety belts arefully tensioned only if the driver actively applies the brakes.respectively) are connected to Airbag Control Module J234 as LIN control modules.• The forward displacement of the front occupants can bereduced by more than 3.9 in (100 mm) by tensioning the safety belts.Audi pre sense frontAudi pre sense front is optional and is offered only when the vehicle is equipped with Adaptive cruise control. Distance Regulation Control Module J428 monitors the traffic in its path and continuously measures the distance between itself and a vehicle driving ahead. J428 evaluates relevant data from other control modules and transfers signals to the data bus. The ACC control module uses these signals to initiate various actions between ABS/ESP Control Module J104 and Instrument Cluster Control Module J285 as necessary. Audi pre sense front is active even if the ACC system is not activated. It has the following functions:Driver Assistance Systems Front Camera R242AProviding driver warning information when following a vehicle ahead at a critical distance in certain situations. In the event of an impending collision with a moving or stopped vehicle, the driver is warned and assistance is provided by automatic braking or by increasing the braking force applied by the driver, which reduces reaction time and vehicle speed. Full deceleration is provided in the event of an impending collision with a moving, stopped or stationary vehicle at a speed of less than 18.6 mph (30 km/h).625_054BDistance Regulation Control Module J428C32 Function AThe driver is warned visually by a message in the Driver Information System when approaching another vehicle ahead or when following this vehicle at a critical distance at a synchronized speed. The critical distance is defined as the distance at which a collision is likely to occur in the event of sudden heavy braking of a vehicle driving ahead, even if the driver of the following vehicle reacts quickly.Approaching vehicle driving aheadSpeed synchronizationFollowing at a critical distance including visual distance warning (ACC warning lamp)Collision609_061Function BWhen the vehicle approaches a moving vehicle, Instrument Cluster Control Module J285 warns the driver visually and audibly if certain defined limits are exceeded. These warnings are issued within a certain period of time prior to the last braking opportunity for collision avoidance before the actual collision. The timing of warnings depends on the driver's degree of activity. Depending on steering, pedal and turn signal inputs, the system classifies the driver as active or inactive and, consequently, as attentive or inattentive. If the driver is attentive, the warning will be issued later than for an inattentive driver. At the same time, ABS/ESP Control Module J104 prefills the brake system and modifies the deployment algorithms for Hydraulic Brake Assist. This means that Hydraulic Brake Assist begins to build up brake pressure even at low brake pedal actuation speeds. If the driver does not respond to the warnings or, for example, eases off the accelerator, J104 performs a warning braking application. The warning braking application is a very brief but easily noticeable braking operation and does not serve to slow the vehicle down. It alerts drivers to the traffic situation and indicates to drivers that they must react immediately in order to avoid an impending collision. Depending on how attentive the system evaluates the driver to be, the warning braking application occurs within a specific period of time ahead of the last opportunity for braking and evasive action in order to avoid a collision. If the driver still fails to react or ease off the accelerator, the vehicle is braked by partial braking operation I, which applies up to 35% of maximum braking force. If Driver Assistance Systems Front Camera R242 also detects the obstacle, the braking force is increased to up to 60% of the maximum by partial braking operation II. If the driver applies the brakes, a target braking action can be performed in all phases described above (prefill brake system, reconfiguration of Hydraulic Brake Assist, driver warning, warning braking application, partial braking operations I and II). During the target braking action, the Audi pre sense front system calculates whether the driver is applying sufficient braking force to be able to avoid a collision. If this is not the case, the required brake pressure is increased depending on the situation.Prefill brake system Hydraulic Brake Assist reacts with higher sensitivityDriver warning visual, audible (forward collision warning)Warning brakingPartial braking operation I or partial braking operation II (on models with front camera for driver assistance systems)CollisionTarget braking33609_063 Function CAudi pre sense front also includes a function for “full deceleration at speeds from 18.6 mph (30 km/h).” If Distance Regulation Control Module J428 detects an impending collision when the vehicle is travelling at a speed of less than 18.6 mph (30 km/h), ABS/ESP Control Module J104 pre-fills the brake system. The deployment algorithms for Hydraulic Brake Assist are adjusted at the same time. Hydraulic Brake Assist thus begins to build up brake pressure even at low brake pedal actuation speeds. If the driver fails to brake or does not apply sufficient braking force in a critical situation, J104 executes a braking action and applies near-maximum braking if necessary. Before the braking action occurs, the driver is alerted both audibly and visually through the DIS that the vehicle is about to brake independently or provide additional braking force. If the vehicle has independently braked to a standstill without driver intervention, three more audible signals are given. The three additional signals given alerts the drivers that they must actively take control over the vehicle by applying the brake. If the driver fails to take control (especially in a vehicle equipped with an automatic transmission) the vehicle will begin to roll.Prefill brake system Hydraulic Brake Assists reacts with higher sensitivityFull deceleration with visual and audible driving warning prior to interventionCollision609_064System characteristics with respect to "full deceleration at speed of less than 18.4 mph (30 km/h)"Driver prioritization over system If the driver clearly takes evasive action, accelerates or brakes during the individual phases of Audi pre sense front (functions A to C), the action momentarily being taken by Audi pre sense front (for example, partial braking operation I) will be suppressed or cancelled. If the obstacle is no longer relevant after evasive action has been taken, Audi pre sense front will cease to provide assistance in this case.• The driver is not given advance warning. • The system reacts to crossing or oncoming vehicles andobjects with low radar scatter (for example, pedestrians).• The system reacts to vehicles which are travelling in thesame direction, have stopped or are stationary.34 Settings and displaysThere are two options for deactivating Audi pre sense front in the MMI.• Option 1: Prewarning off – the audible and visual warnings (distance and forward collision warnings) are deactivated.• Option 2: System off – the audible and visual warnings(distance and forward collision warnings), warning braking, partial and target braking and the "full deceleration at speeds of below 18.4 mph (30 km/h)" functions are deactivated. The functions remain deactivated until they are reactivated in the MMI. Both versions of Audi pre sense are activated.609_078aIf only the pre-warning has been deactivated, no text message is displayed in the DIS. If the system has been deactivated, the driver is warned by a text message in the DIS - Audi pre sense off - whenever the ignition is switched on. This alerts the driver to the fact that the system is switched off.609_079aIf the ESP is set to “Sport” or “OFF” using the ASR/ESP Button E256, then the audible and visual warnings, the warning braking, the partial and target braking, and the "full deceleration at speeds of below 30 kph" functions of Audi pre sense will also be deactivated.Audi pre sense remains deactivated until:• ESP is reactivated with E256. • the ignition is switched off and on again, thereby reactivating ESP.• ACC is activated, since this would result in automaticactivation of ESP. If ESP (Electronic Stabilization Program) is set to "Sport" or "Off" button E256, the following text is temporarily displayed in the DIS: "Audi pre sense: off".Reference For additional information about ACC, refer to eSelf-Study Program 960143, The 2015 Audi A3 Running Gear and Suspension System. Reference For more information about Driver Assistance Systems Front Camera R242, refer to eSelf-Study Program 970343, The 2015 Audi A3 Vehicle Electronics and Driver Assistance Systems.35 Data bus overviewThe overview shows some of the information exchanged via data bus.ABS/ESP Control Module J104 Prefill brake system ← I Warning braking ← I Partial braking operations I and II ← I Target braking ← I Driving speed → O Wheel speed FR → O Wheel speed FL → O Wheel speed RR → O Wheel speed RL → O Brake pressure → O TCS / ESP status → O Activate hazard warning flashers → O Longitudinal acceleration → O Transverse acceleration → O Rotation about vertical axis → O Distance Regulation Control Module J428 Prefill brake system → O Warning braking → O Partial braking operations I and II → O Target braking → O Audible and visual warnings → O Display "Audi pre sense" system malfunction → O Steering angle ← I TCS / ESP status ← I Accelerator position ← I Brake pressure ← I Wheel speed FR ← I Wheel speed FL ← I Wheel speed RR ← I Wheel speed RL ← IVehicle Electrical System Control Module J519 Reversing light switch status → O Close sliding sunroof ← I Close sliding sunroof → O (to LIN user sliding sunroof control unit J245)Power Sunroof Control Module J245 Close sliding sunroof ← I (LIN user of onboard power supply control unit J519)Instrument Cluster Control Module J285 Audible and visual warnings ← I Display "Audi pre sense" system malfunction ← IPower Steering Control Module J527 Steering angle → OSteering Column Electronics Control Module J527 Information Electronics Control Module 1 J794 Audi drive select set-up → O Cruise control system status → OAirbag Control Module J234 Seat belt buckle status → O Passenger airbag status → O Close side windows → O Close tilt/slide sunroof → O Electrical partial tensioning → O (to LIN users front left and right seat belt tensioner control units, J854 and J855 respectively) Electrical full tensioning → O (to LIN users front right and left seat belt tensioner control units, J855 and J854 respectively) Seat belt tensioning status → O Wheel speed FR ← I Wheel speed FL ← I Wheel speed RR ← I Wheel speed RL ← I Longitudinal acceleration ← I Transverse acceleration ← I Rotation about vertical axis ← I Vehicle speed ← I Brake pressure ← I TCS / ESP status ← I Accelerator position ← I Audi drive select set-up ← I Reversing light switch setting ← I Steering angle ← IEngine Control Module J623 Accelerator position → ODoor Control Modules J386, J387, J926, J927 Close side windows ← IFront left belt tensioner control units J854 (LIN user of airbag control unit J234) Electrical partial tensioning ← I Electrical full tensioning ← IFront right belt tensioner control units J855 (LIN user of airbag control unit J234) Electrical partial tensioning ← I Electrical full tensioning ← I609_062Key:Data bus in general LIN bus← I → O Data is received (input) Data is sent (output)36 Engines1.8L and 2.0L TFSI enginesTechnical feature overviewCylinder head with Integrated Exhaust Manifold (IEM)2.0L TFSI engine shown. The 1.8L TFSI engine does not have continuously adjustable exhaust camshaft timing.Optimized thermal managementEngine Temperature Control Actuator N49337 Both the 1.8L TFSI and 2.0L TFSI engines for the North American market will only have the FSI injection system. The dual injection may be introduced at a later date.Combined FSI/MPI injectionFriction optimization and lightweight design609_156Reference For detailed information about the 1.8L and 2.0L TFSI engines, please see eSelf-Study Program 920243, Third generation Audi 1.8L and 2.0L engines from the EA888 model family.625_10738 Diesel engines2.0l Second generation TDI engine Technical featuresCylinder block with integrated balancer shafts609_041Oxidizing catalytic converter and diesel particulate filter609_042Cylinder head with variable valve timing609_04339 Oil pump with integral vacuum pump609_044Active coolant pump609_045Intake manifold module with integrated charge air cooler609_017609_04640 Engine/transmission combinations1.8l TFSI engine0CW2.0l TFSI engine0D92.0l TDI engine0CWTransmission designations:0AH (MQ200_5F) 0AJ (MQ200_6F) 02S (MQ250_6F) 02Q (MQ350_6F) 0FB (MQ350_6A) 0CW (DQ200_7F) 0D9 (DQ250_6A)Explanation of manufacturer designation: Example: MQ350-6FM D Q 350 6 F A Manual transmission Dual clutch transmission Transverse installation Nominal torque capacity Number of gears Front wheel drive All-wheel drive (quattro)41 Notes42 Power transmissionOverviewThe drive train components of the 2015 A3 are based on proven technology and include the new 5th generation Haldex coupling on quattro models. The installation position of the transmission has been adapted to the modular transverse module (MQB) by modifying the transmission flanges and mounting points. The original 6-speed dual clutch transmission 02E is now designated as the 0D9. It’s installation is inclined 12 degrees further back than the 02E.Rear axle drive 0CQFinal drive Rear axle drive ventHaldex coupling ventAll Wheel Drive Control Module J492Haldex Clutch Pump V181Haldex coupling609_12943 ITM for the 02S and 0D9 transmissionsBoth 02S and 0D9 dual clutch transmissions are integrated with the Innovative Thermal Management system for the 2015 A3 model line-up. The 02S is used in the 1.8L A3 Front Track model while the 0D9 is used in the 2.0L quattro model. The transmission cooling circuit is initially open during the start phase of a cold engine. During this time, Transmission Coolant Valve N488 is energized when the ECM switches the valve to ground. If there is enough heat available for the engine and for heating the passenger compartment, the valve is de-energized. The cooling circuit is now closed and the ATF is heated to operating temperature by the engine coolant. The ATF temperature value is transferred from the transmission to the ECM via the Powertrain CAN bus. If the ATF has reached operating temperature, valve N488 is re-energized and the cooling circuit is open. If the ATF temperature exceeds a permissible value, N488 is de-energized again. The cooling circuit is closed. Because the engine coolant temperature is kept below the maximum permissible ATF temperature in this case, the ATF is cooled by the engine coolant.Transmission Coolant Valve N488 −− Activated and diagnosed by the ECM −− Energized: valve closed, open coolant circuit −− De-energized: valve open, closed cooling circuit12VCoolant feed Coolant return609_130Selector mechanism with emergency release. For further information, refer to page 52.12°Selector lever cable for actuating the parking lock0D9 transmission609_13144 5th generation Haldex couplingComponent overviewThe most notable feature of the 5th generation Haldex coupling is a new pressure control system. The hydraulic pressure required for the Haldex coupling is produced by a pump with centrifugal governor. The new Haldex coupling is 3.7 lb (1.7 kg) lighter than the 4th generation coupling. An electric motor drives a six axial piston pump. The pistons are pushed against an inclined thrust plate. When the pump cylinder rotates, the pistons execute an axial stroke and move the Haldex oil to the pressure side of the pump.Axial needle bearingClutch cage Thrust plateThrust plateClutch plate assemblyAxial needle bearingWorking piston with sealsAxial piston pump with integrated centrifugal governorCentrifugal lever Pressure sideHaldex coupling pump V181Axial pistonThrust plateHaldex Clutch Pump V181 Suction sideCentrifugal force control valvePump sump609_13245Pump cylinder All Wheel Drive Control Module J492 All Wheel Drive Control Module J492 exchanges data over the Suspension CAN bus. Its software determines the pump output based upon programmed characteristic curves, which in turn generates the required hydraulic pressure delivered to the working piston cylinder. The electric motor of the pump is controlled with a pulse width modulated 12 volts. Current input is also measured. The hydraulic pressure is determined as a function of current input based on the characteristic curves. If a higher pressure is required, pump output is increased by pulse width modulation of the voltage. To reduce the pressure in the working piston cylinder, pump output is decreased. The system is supplied power via Terminal 30 and is protected by a 15A fuse.Pressure relief valve The Haldex unit hydraulic system is protected by a pressure relief valve. It consists of a valve ball and steel spring. If a hydraulic pressure greater than 638.1 psi (44 bar) develops, the spring force is no longer sufficient to hold the valve ball in place. Its movement unblocks the relief port and the Haldex oil is displaced to the suction side of the axial piston pump.609_133Needle bearing Drive hub2-way connectorAll Wheel Drive Control Module J492 8-way connectorOil sleeveHousingPressure relief valveBall bearing Snap ring Ring sealO-ringFlangeFlanged nut609_13446 Oil supply / hydraulic diagramThe axial piston pump with an integrated centrifugal governor is driven by Haldex Clutch Pump V181. The centrifugal force acting on the centrifugal levers of the controller increases with axial piston pump speed. The valve balls of the centrifugal force control valves are pushed down into the valve seat more firmly. This increases the pressure maintained by the valves. This design allows the system to achieve outstanding pressure increase and pressure reduction times. The hydraulic pressure supplied to the working piston is controlled by varying the speed of Haldex Clutch Pump V181. When the speed of V181 increases, the pressure to the working piston increases. This in turn increases pressure to the clutch plate assembly allowing more torque to be transmitted. If the speed of V181 decreases, there is less pressure supplied to the working piston and less torque can be transmitted.Working pistonPressure relief valveClutch cageHaldex Clutch Pump V181Pressurized oil supply to the working pistonPump sumpThrust plate Axial piston pump with integral centrifugal governorCentrifugal force control valveCentrifugal lever609_13547 Operation - low pump motor speed At low speeds, there is no pressure build-up inside the working piston cylinder. Due to the low speed of the pump motor, the centrifugal levers do not apply pressure to the valve balls.Clutch plate assemblyThe pumped oil flows back into the sump through the centrifugal force control valves of the centrifugal governor.Color key: Vacuum Un-pressurized Oil overflowpressure 638.1 psi (44 bar)Working pistonCentrifugal lever Centrifugal forcePressure relief valveCentrifugal force control valveCentrifugal governor and direction of rotation Centrifugal lever mount Haldex Clutch Pump V181Haldex oil sump609_019Pressure build-up due to increased pump motor speed As the pump motor speed increases, pressure builds up inside the cylinder of the working piston. The centrifugal levers now apply pressure to the valve balls and close the gap. The rising pressure pushes the valve balls back slightly, bringing the centrifugal force and the hydraulic force into equilibrium. The pressure inside the working piston, and therefore, the amount of torque which can be transmitted, rises with increasing motor speed.Color key: Vacuum Un-pressurized Pressure inside working piston cylinderpressure 638.1 psi (44 bar)The valve ball is pushed more firmly into the valve seat by the increased speed of the centrifugal governor.Centrifugal governor with increased speed609_02148 Operation - extremely high pump motor speed At high pump motor speeds, centrifugal levers apply pressure to the valve balls to such an extent that the pressure inside the working piston cylinder rises to an unacceptable level. When the pressure exceeds 638.1 psi (44 bar), the pressure relief valve opens and limits the system pressure.Color key: Vacuum Un-pressurized Excess pressure inside working piston cylinderpressure 638.1 psi (44 bar) Pressure relief valve opensOverspeeding centrifugal governor609_020Pressure reduction due to decreased pump motor speed When the pump motor speed slows, the centrifugal levers exert less pressure on the valve balls. The pressure is relieved through the open valve gap until the centrifugal force and the hydraulic force are equal.Color key: Vacuum Un-pressurized Controlled pressure inside working piston cylinderpressure 638.1 psi (44 bar)Pressure is relievedCentrifugal governor with reduced speed609_05049 Function diagramJ4921212345678J492: All Wheel Drive Control Module V181: Haldex Clutch PumpTerm. 31 Term. 30 Term. 15V181 Suspension CAN bus, high Suspension CAN bus, low609_136All Wheel Drive Control Module J492 communicates with ABS/ESP Control Module J104 and Power Steering Control Module J500 over the Suspension CAN bus.It communicates with DSG Transmission Mechatronic J743, Instrument Cluster Control Module J285, and Engine Control Module J623 via Data Bus On Board Diagnostic Interface J533.ServiceAll Wheel Drive Control Module J492, Haldex Clutch Pump V181 and flange for the propeller shaft are replaceable. Various seals for the housing are also replaceable. Please refer to the current repair literature for the latest information.Haldex oil filler and inspection plugAll Wheel Drive Control Module J492FlangeHaldex oil drain plugAxle oil filler and inspection plug Axle oil drain plugHaldex Clutch Pump V181609_137Oil bleed port for double shaft oil sealChange intervalsThe Haldex oil must be changed every 3 years, regardless of mileage. The axle oil is not subject to a change interval.NoteHaldex oil and rear axle oil are NOT the same. Do not mix them up during service work or irreparable damage to components will occur.50 DiagnosticsAll Wheel Drive Control Module J492 can be accessed with the VAS Scan Tool via Address Word 22. The following functions are available:• Basic setting• Control module identification • Specified/actual comparisonThe validity of the software, the coding and the adaptation channels for the vehicle is checked. • Check DTC memory Query and erase. • Output check diagnosis To activate the output check diagnostics, the engine must be running the coolant temperature less than 140 °F (60 °C). If the output check diagnostic is operating, the multi-plate clutch is kept closed up to a speed of 4 mph (6 km/h). The vehicle must be driven below this speed with the steering wheel at full lock (left or right). This places a strain on the drive line causing the rear axle to shudder. When the driven speed reaches 4 mph (6 km/h), the clutch opens and the strain on the drive line is relieved. This is an indication that the Haldex coupling is working.The basic setting function can be used to assign Haldex Clutch Pump V181 to a matching characteristic curve stored in All Wheel Drive Control Module J492. • Read MVBs • Replace control module Includes all the work operations necessary to replace the control module. Replacing Haldex Clutch Pump V181 After replacing Haldex Clutch Pump V181, the first thing to do is to correct the Haldex oil level. Next, an output check diagnosis must be done on the vehicle while it is stationary and then the oil level checked again. Finally, the basic setting procedure must be performed. Emergency running mode Two temperature sensors are mounted on the printed circuit board of control module J492 which monitor the electronic components. The temperature of the multi-plate clutches is calculated based on these temperature values. If the calculated temperature exceeds a specific threshold, the Haldex coupling is shut off. No indication or warning is given to the driver.51 Transmission selector mechanismY26 P R N D/SB1 B2 B3 B4 B5 B6 B7 B8 B9 B1031 +/- P F319 J587 E313RN D/S58dN110A1 A2 A3 A4 A5 A6 A7 A8 A9 A10Term. 31 P Term. 58d609_138Term. 30 Term. 15 Powertrain CAN bus, low609_139Selector Lever Transmission Range Position Display Unit Y26 Selector lever position If the selector lever is in P, switch F319 is open. It is closed in all other positions. The information "selector lever in P", "switch F319 open" cancels the ignition key removal lock and is required to enable engine starting. If there is a short circuit to ground in the circuit, the engine cannot be started and the ignition key cannot be removed in models without Advanced key. Selector lever positions P, R, N, D/S and the tiptronic signals “tiptronic gate recognition”, “tip plus” and “tip minus” are recognized by Selector Lever Sensor System Control Module J587 and sent to DSG Transmission Mechatronic J743 via the Powertrain CAN bus. To shift from D to S (or S to D), the lever needs only to be flicked backwards out of D/S once. The lever always springs back to the D/S position. E313 Selector LeverPowertrain CAN bus, highF319 Selector Lever Park Position Lock Switch J587 Selector Lever Sensor System Control Module N110 Shift Lock Solenoid Y26 Selector Lever Transmission Range Position Display Unit P A discrete wire to Steering Column Electronics Control Module J527 in vehicles without Advanced key and to Electronic Steering Column Lock Control Module J764 in vehicle with Advance key.Parking lock emergency release mechanism The parking lock emergency release mechanism can be accessed by unclipping the selector lever gate from the center console and pushing the insulating foam to the side.Emergency release mechanism609_14052 Fuel tanksVarious fuel systems are used in the Audi A3 ’13. Various factors dictate which system is fitted in the vehicle:• Engine type • quattro or front wheel drive • Climate zone of marketFuel tank for 1.8L TFSI Front trackFuel tank for 2.0 TFSI quattro modelsFuel tank for 2.0 TDI Front track models with SCR tank53 Exhaust system1.8L TFSI and 2.0L TFSI enginesClose-coupled main catalytic converterCenter mufflerRear muffler2.0l TDI engine609_175Oxidizing catalytic converterDiesel particulate filterExhaust Flap Control Module J883Rear muffler609_03454 Running gearDesign conceptA design goal for running gear of the A3 sedan was to have a finely balanced axle load distribution of 59% front to 41% rear. The forward placement of the front axle in relation to the body played a significant role in this accomplishment. The use of the same components across the worldwide A3 model line-up was also of major consideration. The application of the Audi ultra lightweight strategy was also addressed by the use of aluminum axle components and smaller wheel offsets.OverviewABS/ESP from Continental TPMS standard15“ or 16” inch brakes standard. 17“ inch brakes for S3 sedanTandem master brake cylinder with single 10” or 11” diaphragm power brake booster. (Engine dependent)Distance Regulation Control Module J4