TECHNICAL DOCUMENTATION
SSP 990243 – The 2015 Audi Q3 Introduction

This PDF is currently unavailable.
Read document text
eSelf Study Program 990243The 2015 Audi Q3 Introduction1Audi of America, LLC Service Training Created in the U.S.A. Created 5/2014 Course Number 990243 ©2014 Audi of America, LLC All rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC. Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.NoteThis eSelf Study Program provides a basic knowledge of the design and functions of new models, new automotive components or technologies. It is not a Repair Manual! All values given are intended as a guideline only. For maintenance and repair work, always refer to the current technical literature.ReferenceRevision 2: 6/2014iContentsIntroduction........................................................................................1Dimensions ................................................................................................................................................................. 2Body....................................................................................................4Overview ..................................................................................................................................................................... 4 Body structure ........................................................................................................................................................... 6 Panorama glass sunroof ........................................................................................................................................... 8 Bumper system .......................................................................................................................................................... 9Occupant protection......................................................................... 10System overview ......................................................................................................................................................11 Front airbags ............................................................................................................................................................12Engine............................................................................................... 16The 2.0l TFSI engine ................................................................................................................................................16Transmission..................................................................................... 186-Speed Automatic Transmission 09G/09M .........................................................................................................18Haldex coupling................................................................................ 19Engine/transmission mounting .............................................................................................................................21 Fuel system ..............................................................................................................................................................22 Exhaust system ........................................................................................................................................................23Running gear.................................................................................... 24Overview ...................................................................................................................................................................24 Front suspension .....................................................................................................................................................25 Brake system ............................................................................................................................................................27 Steering system .......................................................................................................................................................31 Wheels and tires / tire pressure indicator .............................................................................................................37Electrical system.............................................................................. 38Power supply ............................................................................................................................................................38 Data Bus On Board Diagnostic Interface J533 (Gateway) ....................................................................................39 Advanced Key ...........................................................................................................................................................42 Control module locations .......................................................................................................................................44 Topology ...................................................................................................................................................................46 Exterior lighting .......................................................................................................................................................50 Audi drive select .......................................................................................................................................................55Climate control................................................................................. 57Engergy efficiency ....................................................................................................................................................57 Refrigerant circuit ....................................................................................................................................................58 Networked components ..........................................................................................................................................60Infotainment.................................................................................... 61Overview of versions ................................................................................................................................................61 MMI displays ............................................................................................................................................................62 Installation locations of control modules .............................................................................................................63 Sound systems .........................................................................................................................................................64 Antenna overview ....................................................................................................................................................66Service.............................................................................................. 67Service interval overview for North American region ...........................................................................................67Knowledge Assessment................................................................... 69iiiiiIntroductionAs the most recent and compact addition to the Audi SUV series, the Audi Q3 caters to the demands of a modern, urban world while offering all the authentic plus-points of an SUV (Sports Utility Vehicle). It complements the successful Audi SUV family started with the launch of the Audi Q7. The Audi Q3 stands out by virtue of its sporty, muscular appearance and its modern, coupe-like styling, and yet it is an authentic SUV through and through. This concept makes the Audi Q3 appealing to more than one target group because it meets a wide variety of customer requirements.The Audi Q3 is not what you would consider a "smaller sibling of the Q5 and Q7", but a vehicle with a very distinctive identity. It has the rugged character of a fully-fledged A-segment SUV coupled with a coupe-like styling unmatched in this segment — and yet it has all the hallmarks of an Audi. The Audi Q3 is compact, flexible and functional and therefore is also a good option for people who do a lot of city driving. The growing number of Audi model series has also led to a growing number of production sites. While the Audi Q3 is an all-new addition to the model range, the production facility in Martorell, Spain and is also a new addition to the Audi production network.602_0121Dimensions62.6 in (1590 mm)361.9 in (1571 mm) 72.1 in (1831 mm)79.5 in (2019 mm)602_03326.5 in (675 mm) 42.0 in (1067 mm) 62.0 in (1575mm)602_03436. (938 9 in. mm )437. (950 4 in. mm )35.4 in (901 mm)102.5 in (2603 mm) 172.6 in (4385 mm)34.7 in (881 mm)602_035230.7 in (781 mm)55.7 in (1417 mm)156.1 in (1426 mm)253.6 in (1362 mm)138.1 in (969 mm)264.2 in (1632 mm) 34.6 in (880 mm) 39.3 in (1000 mm)602_036Length Width Height Track width, front Track width, rear Wheelbase Trailer load with brake at a gradient of 8% Curb weight Max. gross weight172.6 in (4385 mm) 72.1 in (1831 mm) 62.6 in (1590 mm) 61.9 in (1572 mm) 62.0 in (1575 mm) 102.5 in (2603 mm) 2204 lb (1000 kg) FWD: 3494 lb (1585 kg) quattro: 3682 (1670kg) 4651.7 lb (2110 kg)Cabin width, front Cabin width, rear Headroom, front Headroom, rear Through-loading width Load sill height Trunk capacity Fuel tank capacity Drag coefficient in cw55.7 in (1417 mm) 53.6 in (1362 mm) 36.9 in (937 mm) 37.4 in (950 mm) 42.0 in (1067 mm) 30.7 in (781 mm) 16.2/48.2 cu ft (460/1365 liters) 16.9 gal (64 liters) 0.321) 2) 3) 4) width, shoulder room width, elbow room without a roof antenna, vehicle height is reduced by 0.7 in (18 mm) maximum headroomAll dimensions given refer to the unladen weight of the vehicle. 3BodyOverviewThe Audi Q3 body was developed with the focus on lightweight design coupled with a high standard of vehicle safety. The high quality of the materials in the Audi Q3 offers not only advantages in terms of weight reduction, but also provides the basis for meeting the highest standards of vehicle safety.Doors and lidsThe vehicle doors are made of lightweight steel with double sealing lines and sealed joined areas. Vehicle weight was kept to a minimum by using a hood and rear lid made from aluminum. The body including the doors, hood and rear lid weighs approximately 932 lb (423 kg). The body cell without doors and lids accounts for approximately 668 lb (303 kg) of that total.4602_099Key: Mild steels High-strength steels Modern high-strength steels Ultra-high-strength steels Ultra-high-strength hot-formed steel Aluminum panels5Body structureThe main joining method used during Q3 body construction is resistance spot welding. There are approximately 4000 spot welds in the body cell of the Q3. High strength bonding processes are also used in body areas with critical requirements for passive safety, comfort and vibration reduction. New adhesives are used for sealing and corrosion protection in addition to bonding in the Q3. For example, a special expanding adhesive is used in the plenum chamber which eliminates the need for additional sealing compounds. In total, approximately 243 ft (74 m) of adhesive is used in the body cell.Ultra-high-strength hot-formed steel components • • • • • Bulkhead (tunnel bridge) A-pillar, top B-pillar, reinforcement Chassis rail (sill) Tunnel6B-pillar, inner panelThe B-pillar of the Audi Q3 is partially tempered in the shaping process. This imparts ultra-high-strength properties to the steel in the top and bottom sections and only high-strength properties to the steel in the mid-section. The allows the forces exerted on the vehicle body during a side impact to be effectively absorbed.Ultra-high-strengthHigh-strength Ultra-high-strength602_101602_100Key: Soft steels 26% High-strength steels 42% Modern high-strength steels 15% Ultra-high-strength steels 4% Ultra-high-strength hot-formed steels 13%7Panorama glass sunroofA panorama glass sunroof is standard for the Q3. It has an opening front glass element and a fixed rear glass element. It is designed as an externally guided roof system. This means the front glass panel slides over the rear glass panel. This design provides increased headroom inside the passenger compartment.Operating componentsThe operating components of the roof system are housed in the interior light module above the rear view mirror. The roof is operated by a four-way, two stage switch. The roof moves in the same direction the switch is moved. The roof can be moved to any position using the first stage of the switch. With the second stage, the panel moves automatically into its end position. Pushing the switch raises the roof to the tilt position while pulling on the switch closes it.Open glass panelClose roller blindOpen roller blind Tilted glass panel Close opened glass panel Close tilted glass panel602_1028Bumper systemThe front bumper and cover are designed to conform with all applicable safety requirements, provide protection to pedestrians, and be easy to repair. The supporting element is the chrome frame around the radiator grille. The frame is inserted into the mounting boxes of the plastic frame during bumper assembly. The three part bumper cover and the front spoiler are attached to the radiator grille. This multi-part design allows individual components to be replaced so minor damage can be repaired with a minimum of expense. The rear bumper bracket (rebar) is made from aluminum. The cover has two components. There is a bumper cover and an additional lower spoiler and integrated diffuser for the exhaust tail pipes. The pre-assembled parts are attached to the body by guide pieces so it mounts flush to the body at the sides. The wrap-around tailgate necessitated relocating some of the tail lights to the bumper cover. These lights are integrated in the cover together with the sensors for the optional Audi side assist and the antennas for the keyless entry system. The parking aid sensors are attached to the spoiler portion of the assembly.602_104Rear bumper bracketBumper coverSpoiler602_1059Occupant protectionThe Q3 has the following occupant protection equipment • • • • • • • • • • Airbag Control Module Driver and passenger front airbags Front side airbags (head/thorax airbag) Front airbag crash sensors Sideguard curtain airbags Side impact sensors in the front doors Rear side impact sensors Front inertia reel safety pyrotechnic tensioners Safety belt warning for all seats Front passenger seat occupancy detection sensor602_139Key to illustration on following page: E24 E25 E258 E259 G452 G179 G180 G256 G257 G283 G284 G553 G554 J234 J285 J393 J533 J706 Driver Seat Belt Switch Front Passenger Seat Belt Switch Driver Side Rear Seat Belt Switch Passenger Side Rear Seat Belt Switch Front Passenger Seat Occupant Sensor Driver Side Airbag Crash Sensor Front Passenger Side Airbag Crash Sensor Driver Side Rear Side Airbag Crash Sensor Passenger Side Rear Side Airbag Crash Sensor Driver Front Airbag Crash Sensor Passenger Side Front Airbag Crash Sensor Driver Seat Position Sensor Passenger Seat Position Sensor Airbag Control Module Instrument Cluster Control Module Comfort System Central Control Module Data Bus on Board Diagnostic Interface Passenger Occupant Detection System Control Module K19 Seat Belt Indicator Lamp K75 Seat Belt Indicator Lamp K145 Front Passenger Airbag Disabled Indicator Lamp N95 N131 N132 N153 N154 N196 N197 N199 N200 N202 N251 N252 N297 N298 Driver Airbag Igniter Front Passenger Airbag Igniter 1 Front Passenger Airbag Igniter 2 Driver Seat Belt Tensioner Igniter 1 Front Passenger Seat Belt Tensioner Igniter 1 Driver Side Rear Seat Belt Tensioner Igniter Passenger Side Rear Seat Belt Tensioner Igniter Driver Thorax Airbag Igniter Front Passenger Thorax Airbag Igniter Passenger Side Rear Thorax Airbag Igniter Driver Head Curtain Airbag Igniter Front Passenger Head Curtain Airbag Igniter Driver’s Seat Belt Tensioner Igniter 2 Front Passenger Seat Belt Igniter 2T16 Data Link Connector10System overviewLegend: Powertrain CAN bus Convenience CAN bus Diagnosis CAN bus Input signal Output signal602_003b11Front airbagsThe driver’s front airbag is a single stage unit that uses a solid propellant while the passenger side front airbag uses a hybrid gas generator.Driver Airbag Igniter N95N95 is activated by Airbag Control Module J234 which ignites the priming charge. The priming charge then ignites the actual airbag propellant. If the developing gas pressure exceeds a defined threshold due to combustion of the propellant charge, the rupture foil opens the outlets admitting the gas to the airbag. The airbag unfolds and is inflated.Outlet portSpacerPropellant charge Rupture foil602_001FilterPropellant chargeIgniterPriming charge12Occupant protectionFront Passenger Airbag Igniter 1 N131 and Front Passenger Airbag Igniter 2 N132This type of gas generator allows variable degrees of Occupant protection inflation of the front passenger airbag. The Airbag Control Module J234 determines the interval between activation Front passenger side airbag igniter 2 N132 of the two igniters based on accident severity and front Occupant protection passenger position. Like the driver airbag, the front passenger airbag is This type ofseating gas generator allows variable degrees of Front passenger side airbag igniter 1ItN131 equipped with an adaptive gas generator. is a singleinflation of the front passenger airbag. The Airbag Control stage hybrid gas generator with a second Front passenger side airbag igniter 2discharge N132 port. Module J234 determines the interval between activation of the two igniters based on accident severity and front Like the driver airbag, the front passenger airbag is This type ofseating gas generator allows variable degrees of passenger position. Front passenger side airbag igniter 1 equipped with an adaptive gas generator. It N131 is a singleinflation of the front passenger airbag. The Airbag Control stage hybrid gas generator with aigniter second 2 discharge Front passenger side airbag N132 port. Module J234 determines the interval between activation The pyrotechnic propellant charge is integrated in the pressurized gastwo bottle. The based gas (95% argon and 5% helium) is kept at of the igniters on accident severity and front Like the driver airbag, the5081 front psi passenger airbag is a pressure of approximately (400 bar.) This type of gas generator allows variable degrees of passenger seating position. The pyrotechnic charge is integrated in the pressurized gas The gas (95% argon and helium) is equipped with anpropellant adaptive gas generator. It is a singleinflation ofbottle. the front passenger airbag. The5% Airbag Control kept at a pressure of approximately 5081 psi (400 bar.) stage hybrid gas generator with a second discharge port. Module J234 determines the interval between activation Pressurized gas of the two igniters based on accident severity and front passenger seating position. The pyrotechnic propellant charge is integrated in the pressurized gas bottle. The gas (95% argon and 5% helium) is kept at a pressure of approximately 5081 psi (400 bar.) Like the driver airbag, the front passenger airbag is equipped with an adaptive gas generator. It is a singleFront passenger side airbag igniter 1 N131 stage hybrid gas generator with a second discharge port.The pyrotechnic propellant charge is integrated in the pressurized gas bottle. The gas (95% argon and 5% helium) is kept at a pressure of approximately 5081 psi (400 bar.)The ignition charge fired by igniter 1 ignites the actual propellant charge. This causes the pressure inside the pressurized gas bottle to increase until rupture disc 1 bursts. The gas mixture inflates and unfolds the airbag. The ignition charge fired by igniter 1 ignites the actual propellant charge. This causes the pressure inside the pressurised gas bottle to increase until rupture disc 1 bursts. The gas mixture inflates and unfolds the airbag.Igniter 1The ignition charge fired by igniter 1 ignites the actual propellant charge. This causes the pressure inside the pressurised gas bottle to increase until rupture disc 1 bursts. The gas mixture inflates and unfolds the airbag.Propellant chargeThe ignition charge fired by igniter 1 ignites the actual propellant charge. This causes the pressure inside the pressurised gas bottle to increase until rupture disc 1 bursts. The gas mixture inflates and unfolds the airbag.After a defined time period has elapsed, the airbag control module J234 activates igniter 2. A targeted pressure pulse from igniter 2 causes rupture disc 2 to burst. Some of the remaining gas discharged from the pressurised gas bottle now dissipates into the atmosphere and no longer into the airbag.Disc 1After a defined time period has elapsed, the airbag control module J234 activates igniter 2. A targeted pressure pulse from igniter time 2 causes rupture disc 2 to the burst. Some of the remaining gasactivates discharged from 2. the gas bottle After a defined period has elapsed, airbag control module J234 igniter Apressurised targeted pressure pulse now dissipates into the atmosphere no Some longerof into the airbag. gas discharged from the pressurized gas bottle now from igniter 2 causes rupture disc 2 to and burst. the remainingdissipates into thetime atmosphere and no longer into the airbag. After a defi ned period has elapsed, the airbag control module J234 activates igniter 2. A targeted pressure pulse from igniter 2 causes rupture disc 2 to burst. Some of the remaining gas discharged from the pressurised gas bottle now dissipates into the atmosphere and no longer into the airbag.Igniter 210Disc 21013Inertia reel beltsThe Audi Q3 is equipped with pyrotechnic safety belt tensioners in the front seats. The familiar ball-type safety belt tensioners are used. The safety belt tensioners are driven by balls stored in a reservoir tube. In the event of a crash, the propellant charge is ignited by the airbag control module. If the propellant charge is ignited, the expanding gases set the balls in motion, driving them around a gear wheel into the ball receptacle. The safety belt reel is coupled to the gear wheel and also rotated by the balls, tightening/tensioning the safety belt. This type of safety belt does not have the pyrotechnic belt force limiter.Pyrotechnic propellant chargeSeat belt Ball receptacleGear wheel Reservoir tube filled with balls602_01114Notes15EngineThe 2.0l TFSI engineTechnical features • 1st generation EA888 engine without AVS • Four-valve cylinder head with continuously variableintake camshaft timing• Intake manifold with flaps • Cylinder head with Integrated Exhaust Manifold (IEM) • Die cast aluminium oil pan top section(including alminium bolts)• Volume-controlled oil pump • Weight reduced exhaust gas turbocharger housing602_009ReferenceFor further information about the design and operation of the 2.0l TFSI engine, refer to Self-Study Program 921703 "Audi 2.0L Chain-driven TFSI Engine".16SpecificationsTorque-power curve 2.0l TFSI engine with engine code CCTA Power in kW Torque in NmEngine speed [rpm]602_010bEngine code Type Displacement Power output Torque Number of valves per cylinder Bore in mm Stroke in mm Compression ratio Powertrain type Engine management Fuel Emissions standard CO2 emission in g/kmCCTA Four-cylinder inline engine 121.1 cu in (1984 cc) 200 hp (150 kW) @ 5100 - 6000 rpm 207 lb ft (280 Nm) @ 1700 -5000 rpm 4 3.25 in (82.5 mm) 3.70 in (92.8 mm) 9.6 : 1 6-speed automatic transmission Bosch MED 17.1 Premium unleaded (sulphur-free) 95 RON SULEV 17417Transmission6-Speed Automatic Transmission 09G/09MThe Japanese automatic transmission manufacturer AISIN Co. LTD in conjunction with Audi engineers has adapted a six-speed automatic transmission for the front wheel drive and quattro versions of the Q3. The transmission is adapted for use with different engines and vehicles by varying:• The number of disc pairs for clutches and brakes • The adaptation of the ATF pressure on the clutches andbrakes• The configuration of gear pairs, planetary gear sets (fourinstead of three planetary gears), shafts and bearings• The reinforcement of housing components • The ratio of the final drive and the intermediate drive • The size of the torque converters309_068• The torque converter characteristic curve of the torqueboost (conversion factor or conversion boost)• The selector lever • The ignition key removal lockThe transmission sets new standards in dynamics and efficiency through: • Low weight • High overall transmission ratio spread • Compact dimensions of the transmission • High speed of shifting • High level of shifting comfortATF coolerMulti-function switchIn addition to using conventional planetary gearsets, the 09G and 09M transmissions use a Lepelletier gear arrangement. The advantage of the Lepelletier arrangement is its simple, space-saving and lightweight design. It combines a simple planetary gear set with a subsequent Ravigneaux arrangement. This makes six speeds possible with only five shifting elementsElectrical connectionss309_00218Haldex couplingThe drive train components of the Audi Q3 quattro are based on proven technology and include the new 5th generation Haldex coupling on quattro models. The most notable feature of the 5th generation Haldex coupling is a new pressure control system. The hydraulic pressure required for the Haldex coupling is produced by a pump with centrifugal governor. The new Haldex coupling is 3.7 lb (1.7 kg) lighter than the 4th generation coupling. An electric motor drives a six axial piston pump. The pistons are pushed against an inclined thrust plate. When the pump cylinder rotates, the pistons execute an axial stroke and move the Haldex oil to the pressure side of the pump.Rear axle drive 0CQFinal driveRear axle drive ventHaldex coupling ventAll Wheel Drive Control Module J492Haldex Clutch Pump V181Haldex coupling609_129ReferenceFor more detailed information about the operation of the 5th generation Haldex coupling, please see eSelf-Study Program 990143, The 2015 Audi A3 Introduction.19Function diagramJ4921212345678J492: All Wheel Drive Control Module V181: Haldex Clutch PumpTerm. 31 Term. 30 Term. 15 V181 Suspension CAN bus, high Suspension CAN bus, low609_136All Wheel Drive Control Module J492 communicates with ABS/ESP Control Module J104 and Power Steering Control Module J500 over the Suspension CAN bus.It communicates with Transmission Control Module J217, Instrument Cluster Control Module J285, and Engine Control Module J623 via Data Bus On Board Diagnostic Interface J533.ServiceAll Wheel Drive Control Module J492, Haldex Clutch Pump V181 and flange for the propeller shaft are replaceable. Various seals for the housing are also replaceable. Please refer to the current repair literature for the latest information.Haldex oil filler and inspection plugAll Wheel Drive Control Module J492FlangeHaldex oil drain plugAxle oil filler and inspection plug Axle oil drain plugHaldex Clutch Pump V181609_137Oil bleed port for double shaft oil sealOil change intervalsThe Haldex oil must be changed every 3 years, regardless of mileage. The axle oil is not subject to a change interval.NoteHaldex oil and rear axle oil are NOT the same. Do not mix them up during service work or irreparable damage to components will occur.20Engine/transmission mountingThe engine/transmission mounting is a key factor in reducing unwanted noise and vibration transfer to the passenger compartment. The hydraulic damping in the bearings essentially reduces low frequency engine/transmission movements to optimize occupant comfort. The engine torque is absorbed by the stabilizer link rod, which is designed as an elastomer bearing and connected directly to the gearbox and vehicle body via the subframe.OverviewHydraulic engine bearing Damping fluid with injector plateCarrier partSupport armDiaphragmHydraulic transmission bearing602_097Stabilizer link bar21Fuel systemThe Q3 has a 16.9 gal (64.0l) saddle-type fuel tank. The fuel tank version for the North Amerian market will also have the required ORVR system (not shown.) A lever-type sender in each of the main and secondary chambers ensures a high display accuracy. A three-wire thick film sensor is used. The additional wire supplies a redundant signal which is used to arithmetically eliminate contact resistance factors created by the use of aggressive fuels. Consequently, resistance is no longer a factor affecting the accuracy of the display. The lever-type sensor is mounted to the bottom-supported swirlpot of the fuel delivery unit. Fuel supply is regulated according to demand. Only the actual amount of fuel needed is made available. Brushless, electrically commutated fuel pumps are used.Fuel tank and fuel level senderConnections for the activated charcoal filter (ACF)Lever-type senderExpansion tank Bracket for Fuel Pump Control Module J538 Float-type vent valve with roll-over functionMain chamberFuel Pump G23 Lever-type sender 1 Lever-type sender 2 Tank ventilation Suction jet pumpSecondary chamber602_09622Exhaust systemThe overall weight of the exhaust system was kept low through the use of high grade stainless steel, low wall thickness pipes and lightweight mufflers. Due to its low weight and low exhaust backpressure, the overall catalytic converter and silencer system significantly reduces CO2 emissions. Both ceramic and metal catalytic converter substrates are used in the exhaust gas after treatment system. To reduce structure-borne sound, the shells of the rear silencer have reinforcing beads.The 2.0l TFSI engineClose-coupled catalytic converter with ceramic substrateDecoupling elementCatalytic converter with ceramic substrateCenter muffler (designed as a reflection muffler)Rear muffler (designed as an absorption muffler)602_09823Running gearOverviewA fundamental goal in the development of the suspension system for the Audi Q3 was to set new standards in driving experience in this premium SUV segment. To achieve this, use is made of a newly designed MacPherson strut front axle with aluminium wishbones and a multilink rear suspension. A vehicle weight distribution of 58% on the front suspension, the wide front and rear vehicle tracks, and the use of larger diameter wheel and tire combinations enhances the excellent driving characteristics of the Q3.VersionsOnly the standard suspension version will be available at the launch of the Q3.602_04324Front suspensionThe front suspension of the Q3 is based on the transverse platform (MQB) used throughout the Group. A key new development is the control arm rear bearing. It is a major factor contributing to outstanding steering response and agility. Minimal bearing motion in the transverse direction provides a high camber thrust rate and optimal cornering stability. The front axle configuration in combination with the design of the rubber bearings results in neutral handling at the limit of adhesion with a slight understeer. A large positive caster angle and wheel offset provides excellent straight line stability.602_044Linear-rate steel springs with progressive-rate polyurethane auxiliary springsTube-type anti-roll barAnti-roll bar linkCoil-over suspension strut bearings with separate spring/damper mountings602_045The control arm and wheel carrier are connected by a ball joint.Wishbone (forged aluminum part)Three-piece engine/transmission mounting (aluminium chill casting)Wheel carrier (nodular cast iron)25Rear suspensionThe rear suspension components of the front wheel drive and quattro models are identical.Upper control arm (Welded sheet metal)Spring link (Welded steel)Engine/final drive mount (Sheet steel construction)High-strength linearrate steel spring602_046Anti-roll bar link (Steel construction)Tie rod (Sheet steel construction)Thin-walled tubular anti-roll barsWheel carrier (Aluminum casting)Wheel bearing with integral wheel hubSuspension alignmentThe front axle camber can be adjusted by equalization. Front toe can be adjusted individually. Toe and rear camber can be adjusted individually on the rear suspension.Brake systemOverviewThe Q3 uses a high performance ABS/ESP system by TRW specially designed to meet the demands of an SUV. The use of an electromechanical parking brake allows the additional features of Hold Assist and speed dependent emergency braking to be available for the Q3.602_049Brake specificationsFront axle Rear axleEngine type Brake type Number of pistons Piston diameter Brake disc diameter2.0l TFSI 16“ FN3 57/25/13.5 floating caliper brake 1 2.24 in (57 mm) 12.3 in (312 mm), vented brake discs2.0l TFSI 16“ CII 41 EPB aluminium floating caliper with actuators for the Electric Parking Brake (EPB) 1 1.61 in (41 mm) 11.1 in (282 mm), solid brake discs27Brake servo and master brake cylinderAn 11-inch single brake booster with a “single rate” characteristic is used on the Q3. The aluminum tandem master brake cylinder with a 0.9 in (23.8 mm) diameter provides the necessary performance with short brake pedal travel and a low pedal actuation force. A non-contact Hall sensor is used to actuate the brake lights.602_052Brake applicationThe foot pedal assembly is a modular design to save weight. The pedals are manufactured from fiber-reinforced plastic while the brake pedal bearing assembly is manufactured as a sheet steel component with a weight saving shell design.612_030Service operationsThe service operations on the brake system are the same as for systems already in use on other Audi models.28Electro-mechanical parking brake (EPB)Design and operation The Q3 uses an electromechanical parking brake system similar those used in other Audi models. In the Q3, Transverse Acceleration Sensor G200, Rotation Rate Sensor G202 and Longitudinal Acceleration Sensor G251 are integral with Electromechanical Parking Brake Control Module J540. These integrated sensors replace ESP Sensor Unit G419.Parking Brake Pressure Switch F234Right Parking Brake Motor V283Electromechanical Parking Brake Control Module J540 with Transverse Acceleration Sensor G200, Rotation Rate Sensor G202 and Longitudinal Acceleration Sensor G251602_054Left Parking Brake Motor V282Service operationsIf Electromechanical Parking Brake Control Module J540 is replaced, it must be coded online. After the online coding, the basic setting procedure must be carried out to calibrate Transverse Acceleration Sensor G200 and Longitudinal Acceleration Sensor G251.29ESPDesign and operation The Audi Q3 uses and ABS/ESP system by TRW (TRW 450). In addition to the basic functions EBD, ABS, ASR, EDL and ESP, the following additional functions have been implemented: Standard features:• • • • • • Torque vectoring on vehicles with quattro drive Hydraulic Brake Assist Hydraulic brake booster Brake disc wiper Hydraulic brake fading compensation Driver steering recommendation (DSR)602_055Active wheel speed senders are used on the Audi Q3.602_056Service operationsThe ABS/ESP Control Module and hydraulic unit can be sepa rated for repair. The same condition applies here as to the other Audi models: control modules can be replaced indi vidually but the entire ABS/ESP module must be replaced if hydraulic modules are faulty. After replacing an ABS/ESP Control Module, it must be encoded online. Steering Angle Sensor G85 must be calibrated and initialized through Power Steering Control Module J500. Several basic settings must then be configured. At the same time, the brake pressure, longitudinal acceleration, transverse acceleration and yaw rate senders are calibrated.30Steering systemOverviewThe Q3 uses an electromechanical power steering system similar to that used in the A7 Sportback. When compared to conventional hydraulically boosted steering systems, the electromechanical system reduces fuel consumption and provides greater potential for optional equipment.Mechanically adjustable steering column. (approximately 2 in [50 mm] of vertical and horizontal adjustment)602_057Electromechanical steering system with axial parallel drive31Electromechanical steeringOverview The compact unit consists of the actual steering gear, an electric motor for power assistance, a control module, a sensor for measuring steering torque and a sensor for monitoring the position of the electric motor rotor.Electromechanical Power Steering Motor V187Rack and pinion steering gearSteering Torque Sensor G269Power Steering Control Module J500602_058Drive V187 is powered directly by Power Steering Control Module J500. The rotational movement of the motor is converted to the linear movement of the steering rack by a recirculating ball nut assembly. The ball nut is driven by a toothed belt. The current intensity with which the motor is activated regulates the amount of assist of the steering torque.Recirculating ball nut602_059Electromechanical Power Steering Motor V187Toothed beltReferenceFor detailed information about the general design and function of the steering gear, refer to eSelf-Study Program 990303, The 2012 Audi A7 Running Gear and Suspension Systems.32The recirculating ball nut is fixed in a longitudinal direction. If it is turned, there is a linear movement of the spindle in the direction of the arrow.To restrict the contact among the ball bearings, “ball circuits” that are as short as possible are used. This is why the ball nut has individual circuits.Direction of rotation of the recirculating ball nutLinear movement of the spindle/rackRotation direction of the recirculating ball nut602_060602_061Ball raceReturn channelRecirculating ball nutLinear movement of the spindle/rackSteering Torque Sensor G289 Steering torque is measured by Steering Torque Sensor G289. The steering input shaft and steering pinion are interconnected by a torsion bar. Turning the steering wheel results in minimal rotation of the torsion bar and also the input shaft relative to the steering pinion. The angle of rotation is measured by the the sensor and is a direct measure of steering torque.Steering input shaftSteering Torque Sensor G289Steering pinion602_06233Electromechanical Power Steering Motor V187 The Audi Q3 uses a permanently excited three-phase AC synchronous motor for steering assistance. This motor concept was chosen on the basis of the following key advantages:Toothed belt drive pinion• Synchronous motors are noted for their compact designand high performance.• Permanent excitation eliminates the need for slip ringsfor transmitting the exciter current to the rotor.The necessary phase voltages are calculated by the Power Steering Control Module and applied through the power output stages. The stator has nine field coils arranged in groups of three and connected in series. They are energized by a sine-wave current. The three electric currents are phase offset relative to one another. The three magnetic fields generated produce a rotating magnetic field which induces a synchronous rotational movement in the rotor. The rotor has six permanent magnets alternately arranged in a north/south direction. For smoother running, the six pole ring magnet is magnetized at an angle.Rotor position sensorStatorRotor602_063Receiver coilsRotor discRotor position detection The rotor position sensor monitors the position of the rotor. The control module must know the exact position of the rotor to be able to calculate the phase voltages required for the rotating magnetic field (electronic sensor controlled commutation). The measured value of the rotor position sensor is also utilized to define the steering stops. To avoid hard mechanical stops, "soft" limits stops are implemented by the electromechanical steering system.The exciter coil is supplied with a sine-wave exciter voltage. The alternating magnetic field which develops around the exciter coil acts upon the rotor disc. The rotor disc conducts the magnetic flux of the alternating magnetic field generated by the exciter coil to the receiver coils. This induces in the receiver coils an alternating voltage which is phase offset proportional to the position of the rotor disc relative to the exciter voltage.602_064Exciter coil34General functional principleWhen the steering wheel starts to turn, the torsion bar connecting the steering input shaft to the steering pinion is rotated. This rotation is measured by the steering torque sensor and sent to the control module. At the same time, the control module receives more signals relevant to the operation of the steering system: The control module evaluates this information and calculates the electrical current and the phase shift required by Electromechanical Power Steering Motor V187. This is based on stored map in the control module. When the motor is activated, its torque is transmitted to the ball nut assembly by the toothed belt. Depending on the drive current level, a defined amount of torque is provided for steering assistance. The resultant force acting on the steering rack is made up of the steering torque applied by the driver and the torque generated by the electric motor.• • • • the steering angle from the Steering Angle Sensor G85. the driving speed from the ABS/ESP Control Module RPM for the Engine Control Module. and the current position of Electromechanical Power Steering Motor V187 through its rotor position sensor.674 25 3Steering movement by the driverDirection of movement of the rotor with recirculating ball nutForce acting on the rack as the sum total of the steering force applied by the driver and the steering assistance provided by the electric motor 1602_065Key: 1 2 3 4 5 6 7 Steering movement by the driver Signal from the steering torque sensor Signal from the steering angle sensor Activation of the electric motor Recirculating ball nut drive Steering torque applied by the driver Steering torque applied by the electric motor35Additional functionsVarious adjustments and functions are implemented by the electromechanical steering system in addition to its basic assist function. The driver is assisted in certain driving situations in the following ways:• The "straight-ahead driving correction" function takesthe strain off the driver when driving in a straight line against a constant, sustained crosswind or when driving on a cambered road surface. A corrective steering torque is generated by active steering assistance.• Speed-dependent power assisted steering (Servotronic)is standard.• The Audi Q3 also uses the "DSR" (driver steeringrecommendation) function implemented previously in the A7 Sportback in combination with ESP and electromechanical steering.• Return of the steering wheel to the straight-aheadposition after steering lock has been applied is assisted by the "active reset" function. This enhances both directional stability and steering comfort.• Steering comfort is enhanced by implementing dampedmaximum steering locks.Operation and driver informationThe driver can choose between three different steering maps. Setting of the steering characteristic - from comfortable to sporty - is coupled to the setting in Audi drive select.efficiencyAudi drive selectHandbookdynamic comfort autoCar SystemsEuropean version602_066Service operationsProtective boots and track rods are the only individual components that can be replaced at this time. In the event of other component failures, the entire steering unit must be replaced. Power Steering Control Module J500 must be encoded online. Once the “encode control module” Test Plan has been initiated, the vehicle data record is downloaded. The software for the particular vehicle is loaded from a central database. Within the encoding framework, the vehicle’s equipment level is downloaded to the module. Because the steering limit stops have not yet been stored in the new control module, coding must be followed by running the “Learn steering limit stops” Test Plan.36Steering wheelsThe steering wheel and airbag have been systematically designed for lightweight construction. Weight has been reduced by approximately 1.1 lb (0.5 kg) by the use of ultra-lightweight magnesium in the steering wheel skeleton and fibre-reinforced plastic in the airbag. The multifunction steering wheels allow user-friendly operation of the driver information system including telephone, audio devices and onboard computer.Two additional optional paddle switches allow gear changes to be performed manually on models with S tronic. The steering wheels come in two optional color versions matching the vehicle interior. OverviewOption Multi-function sports steering wheel of 3-spoke designOption Multi-function sports steering wheel of 3-spoke design including shift paddlesWheels and tires / tire pressure indicatorWheels and tires overviewThe wheel/tire combinations used for the Audi Q3 ensure superb handling, comfort and driving stability for a vehicle of this class. All engine types are equipped with size 6.5J x 16 forged aluminium wheels even in the basic trim.Standard 18“ wheels 7J x 18 ET43 Lightweight aluminium wheel, brilliant silver finish 235/50 R18Optional 19” wheel 8.5J x 19 ET36 5-Double-spoke-Offroad-Design 255/40 R19 all-season tiresTire Pressure Monitoring SystemThe Q3 is equipped with the second generation tire pressure monitoring system. By evaluating the vibration characteristics of each wheel/tire, the new TPMS system is capable of determining and indicating which tire is experiencing pressure loss. The system can also detect slow (gradual) pressure loss, as well as simultaneous pressure loss at several wheels.37Electrical systemPower supplyBatteryThe vehicle battery is located in the engine compartment and is protected by an insulating blanket. Battery size, type and protection are dependent on engine, trim level and country version. All Q3 models will have an energy management system and a brake energy recuperation* function. The North American version of the Q3 will be equipped with a 68Ah/ 280A battery and a 140A alternator.Battery e-box with fuses and relays. Designation in Wiring Diagram: “SB”Jump start points / fuses and relaysThe battery positive terminal and the ground stud near the left-hand strut tower are used for battery charging and jump starting.Ground stud Relay carrier below lefthand side of instrument panelRelay carrier on Vehicle Electrical System Control Module J519 Fuse carrier below left hand side of instrument panel. Designation in Wiring Diagram: “SC” Voltage test connectors on e-box. Designation in Wiring Diagram: “SA”Relay carrier below the e-box602_108*Upon deceleration the energy created is lost. Brake energy recuperation recycles this energy to lighten the load on the engine. It can reduce fuel consumption by up to 3%. When coasting or braking, the car’s alternator generates energy. Brake energy recuperation allows this energy to be stored. When accelerating or driving at a constant speed this stored energy is used so less energy is wasted in driving the alternator. This lowers fuel consumption and CO2 emissions.38Data Bus On Board Diagnostic Interface J533 (Gateway)Two versions of J533 are used on the Q3 dependent on the Infotainment system. One version is for vehicles with an Infotainment CAN and a version for vehicles with an optical bus (MOST). Depending on optional equipment, four LIN slave modules could be connected to J533:• • • • Power Sunroof Control Module J245 Roof Shade Control Module J394 Battery Monitoring Control Module J367 Alternator CJ245 J367J394 C J533 LIN602_109Summary Designation Installation position Bus systems Data Bus On Board Diagnostic Interface J533 Under instrument panel, driver footwell Convenience CAN bus (always installed) Powertrain CAN bus (always installed) Instrument Cluster CAN bus (always installed) Diagnostics CAN bus (always installed) Extended CAN bus (option) Infotainment CAN bus (dependent on infotainment version) MOST bus (dependent on Infotainment version) LIN bus Tasks • • • • • 100 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 100 kbit/s 22 Mbit/s 20 kbit/s Single-wire capable Not single-wire capable Not single-wire capable Not single-wire capable Not single-wire capable Single-wire capable Ring structure (open circuit results in failure) Single-wire bus systemNetworking gateway Diagnostic interface Transport mode (for transportation or long periods of non-use) Wake-up monitor (monitors bus standby mode or bus wake-up function) Energy management LIN master for: • Battery Monitoring Control Module J367 (always installed) • Alternator C (always installed)• Control of the panorama glass sunroof and sunroof roller blind LIN master for: • Sunroof Control Module J245 (option) • Roof Shade Control Module J394 (option) Address Word 1939Battery Monitoring Control Module J367Summary Designation Battery Monitoring Control Module J367Battery negative poleInstallation positionon the negative terminal of batteryTasksMeasurement of: • car battery charging and discharge currents • battery voltage • battery temperatureAddress WordNone, LIN slave, measured data and diagnostics via J533 Gateway602_110Battery monitor control module J367Alternator CSummary Designation Alternator CInstallation positionat bottom front right of engine, driven by poly V beltTasksCharging the vehicle batteryAddress WordNone, LIN slave, measured data and diagnostics via J533 (master)602_111Power Sunroof Control Module J245 and Roof Shade Control Module J394Summary Designation Power Sunroof Control Module J245 Roof Shade Control Module J394Installation positionin the roof areaTasksOpening and closing the sliding sunroof or the sunroof roller blindAddress WordNone, LIN slave, measured data, diagnostics and Output Check Diagnosis via J533 (master)602_11340Vehicle Electrical System Control Module 1 J519Summary Designation Vehicle Electrical System Control Module J519 Always installed Under the left side of the instrument panelEquipment Installation positionTasksCentral locking master Exterior light master Interior light master Antitheft alarm master Activation of various relays Activation of various convenience components: • Seat heaters • Heated windshield washer nozzles • Windshield washer pump • Headlight washer system pump • Reading various switch and button positions • Reading various sensor values• • • • • • 610_009J519Address Word Data bus communication09 • Convenience CAN bus participant • J519 is the LIN master for: • LIN 1 – Light Switch E1, Wiper Motor Control Module J400, Rain/ Light Recognition Sensor G397, Humidity Sensor G355 • LIN 2 – Alarm Horn H12 • LIN 3 – Power Sunroof Control Module J245, Anti-theft Alarm System Sensor G578 LIN 1 is distributed to two pins on J519. J400 is connected to pin B30. E1, G397 and G355 – are connected to pin C28. This means that the control modules connected to pin C28 are also affected in the event of a short circuit to positive or negative at pin B30Special featureReferenceFor a detailed description of Vehicle Electrical System Control Module J519, please see eSelf-Study Program 970343, The 2015 Audi A3 Vehicle Electronics and Drivers Assistance Systems.41Advanced KeyThe Audi Q3 can be equipped with an advanced key.Terminal 30 R134 R135 R136 R138 R139 Terminal 58st E408Terminal 30Access/Start Authorization Control Module J518Electronic Steering Column Lock Control Module J764Terminal 15"Wake up" LineG415G416Vehicle Electrical System Control Module 1 J519Internal antenna for central lockingNO contactConvenience CAN busEngine Control Module J623E234"Terminal 50"RequestGearbox selector position "P"7.5 A7.5 AKey: E234 Release Button in Rear Lid Handle E408 Access/Start Authorization Button G415 Driver Exterior Door Handle Touch Sensor602_134R135 Front Passenger Access/Start System Antenna R136 Access/Start System Antenna in Rear Bumper R138 Access/Start System Antenna 1 in Vehicle Interior R139 Access/Start System Antenna 2 in Vehicle InteriorG416 Front Passenger Exterior Door Handle Touch Sensor R134 Driver Access/Start System Antenna42Notes43Control module locationsSome of the control modules shown in this overview may be optional and/or country specific. Always refer to ElsaPro for details about control module locations and instructions for installation and removal.J387J668J745 J518Ρ242 J540 J623 J685 J500 J533 J743 J794 J255 J587J285 J217 J764 G85 J527 J453J667J104J519J386Key: G85 Steering Angle Sensor J104 ABS/ESP Control Module J217 Transmission Control Module J234 Airbag Control Module J255 Climatronic Control Module J285 Instrument Cluster Control Module J386 Driver Door Control Module J387 Front Passenger Door Control Module J388 Left Rear Door Control Module J389 Right Rear Door Control Module J453 Multifunction Steering Wheel Control Module J492 All Wheel Drive Control Module J500 Power Steering Control Module J518 Access/Start Authorization Control Module J519 Vehicle Electrical System Control Module 1 J525 Vehicle Electrical System Control Module 1 J527 Steering Column Electronics Control Module J533 Data Bus On Board Diagnostic Interface44J389J769 J791J525J234J492J770 Radio RR41J772J388602_092J540 Electromechanical Parking Brake Control Module J587 Selector Lever Sensor System Control Module J623 Engine Control Module J667 Left Headlamp Power Output Stage J668 Right Headlamp Power Output Stage J685 Front Information Display Control Head J745 Cornering Lamp and Headlamp Range Control Module J764 Electronic Steering Column Lock Control Module J769 Lane Change Assistance Control ModuleJ770 Lane Change Assistance Control Module 2 J772 Rearview Camera System Control Module J791 Parallel Parking Assistance Control Module J794 Information Electronics Control Module 1 R Radio R41 CD changer R242 Driver Assistance Systems Front Camera45TopologyModels with infotainment CAN busAlarm horn H12 Wiper Motor Control Module J400Anti-theft Alarm System Sensor G578Rain/Light Recognition Sensor G397Humidity Sensor G355 Instrument Cluster Control Module J285Vehicle Electrical System Control Module 1 J519Data Link ConnectorMultifunction Steering Wheel Control Module J453Steering Column Electronics Control Module J527Data Bus On Board Diagnostic Interface J533 Climatronic Control Module J255Engine Control Module J623 Left Rear Door Control Module J388 Driver Door Control Module J386Transmission Control Module J217Airbag Control Module J234 Right Rear Door Control Module J389 Front Passenger Door Control Module J387 Steering Angle Sensor G85 Trailer detector control unit J345 ECD control unit (electronically controlled damping) J250 Power Steering Control Module J500Selector Lever Sensor System Control Module J587All Wheel Drive Control Module J492Access/Start Authorization Control Module J518Parallel Parking Assistance Control Module J791Electronic Steering Column Lock Control Module J764Headlight assist control unit J844Vehicle tracking system interface control unit J843ABS/ESP Control Module J104Cornering Lamp and Headlamp Range Control Module J745Rearview Camera System Control Module J772Electromechanical Parking Brake Control Module J540Key: Powertrain CAN bus Convenience CAN bus Extended CAN bus Infotainment CAN bus Diagnostics CAN bus Instrument cluster CAN bus LIN bus Sub-bus systems46Power Sunroof Control Module J245Roof Shade Control Module J394Radio RFront Information Display Control Head J685Front camera for driver assistance systems R242Lane Change Assistance Control Module J769Battery Monitor Control Module J367Lane Change Assistance Control Module 2 J770Alternator CVoltage stabilizer J532Left Headlamp Power Output StageRight Headlamp Power Output Stage602_09147Models with MOST busAlarm horn H12Wiper Motor Control Module J400Anti-theft Alarm System Sensor G578Rain/Light Recognition Sensor G397Humidity Sensor G355 Instrument Cluster Control Module J285Vehicle Electrical System Control Module 1 J519Data Link ConnectorMulti-function Steering Wheel Control Module J453Steering Column Electronics Control Module J527 Data Bus On Board Diagnostic Interface J533 Climatronic Control Module J255 Engine Control Module J623 Transmission Control Module J217Left Rear Door Control Module J388Driver Door Control Module J386Airbag Control Module J234 Right Rear Door Control Module J389 Passenger Door Control Module J387 Steering Angle Sensor G85 Trailer detector control unit J345 ECD control unit (electronically controlled damping) J250 Power Steering Control Module J500Selector Lever Sensor System Control Module J587All Wheel Drive Control Module J492Access/Start Authorization Control Module J518Parallel Parking Assistance Control Module J791Electronic Steering Column Lock Control Module J764Headlight assist control unit J844Vehicle tracking system interface control unit J843ABS/ESP Control Module J104Cornering Lamp and Headlamp Range Control Module J745Rearview Camera System Control Module J772Electromechanical Parking Brake Control Module J540Key: Powertrain CAN bus Convenience CAN bus Extended CAN bus Diagnostics CAN bus Instrument cluster CAN bus MOST bus LIN bux Sub-bus systems48Front Information Display Control Head J685Power Sunroof Control Module J245Roof Shade Control Module J394Information Electronics Control Module J794Radio RCD Changer R41Front camera for driver assistance systems R242RLane Change Assistance Control Module J769Media Oriented Systems TransportDigital Sound System Control Module J525Battery Monitoring Control Module J367 Lane Change Assistance Control Module 2 J770Alternator CVoltage stabilizer J532Left Headlamp Power Output Stage J667Right Headlamp Power Output Stage J668602_09049Exterior lightingXenon plus HID headlightsThe Q3 comes equipped with Xenon plus headlights. The daytime running lights and side light are provided by LEDs via a plastic optical fiber cable. The two LEDs are mounted on the LED module. They cannot be replaced separately. In the event of a fault, the LED module can be replaced.Daytime running light and side light control unitTurn signal PY24WHeadlight range control motorLow and high beam gas discharge lamp (D35)Daytime running light and side light 2 LEDs on LED moduleHeadlight power moduleGas discharge lamp control unit602_094Light functions Daytime running light Parking light Low beam Cornering light High beam Turn signal Fog light (integrated in the bumper, not shown)Illuminants used 2 LEDs with plastic optical fibers (dimmed to approx. 25 %) Gas discharge lamp D3SPower approx. 10 watts 35 wattsBulb PY24W Bulb H1124 watts 55 wattsDaytime running light and side lightBoth LEDs for the daytime running light are operated at 100% of their capacity. The daytime running light is disabled when the turn signals are activated.50Dynamic headlight range controlSchematic diagram of the activation mechanism for Xenon plus headlightsConvenience CAN busXenon plus headlight (one side of vehicle) Discrete lines Vehicle Electrical System Control Module 1 J519 Daytime running light and side light control unit LED module Turn signal 24 watt bulb PY24W Ballast for gas discharge lamp D3SPowertrain CAN busCornering Lamp and Headlamp Range Control Module J745Power module for headlights Private bus (sub-bus)Discrete linesLeft Rear Level Control System Sensor G76Left Front Level Control System Sensor G78Headlight range control servomotor Dynamic cornering light servomotor602_11651Tail lightsThe Q3 for the North American market will be equipped with LED tail lights. Some of the lights will be installed in tailgate while additional lights will be installed in the lower bumper cover. The tail lights are activated by Vehicle Electrical System Control Module 1 J519. The tail lights in the tailgate are disabled when it is in the raised position. The tail lights in the lower bumper spoiler are then illuminated. None of the component parts of the LED tail lights in the tailgate can be replaced.LED tail lightTurn signalTail light602_118Brake lightTail lightLight functions Tail light Brake lightIlluminants used 2 LEDs with plastic optical fibres 18 red LEDsActivation mechanism 100% 100%Power approx. 2 watts approx. 3.5 watts52Additional tail lightsAdditional tail lights in the Audi Q3 are needed because the tail lights also swing up when the tailgate is opened. They are integrated in the bumper and accommodate the back-up light and rear tail light functions, as well as the turn signal and the tail/brake light when the tailgate is open. The additional tail lights can be removed to replace the bulbs from the rear bumper. A close-out cover which provides access to the light retaining bolts is integrated in the bumper cover for this purpose.Turn signalTail/brake light602_119ReflectorBack-up lightRear fog lightLight functions Tail light Brake light1)1)Illuminants used Bulb W16W Bulb W16W Bulb W16W Bulb W16WActivation mechanism dimmed to approx. 30 % 100 % 100 % 100 % 100 %Power 16 watts 16 watts 16 watts 16 wattsTurn signal1) Rear fog light Back-up light1)active only when tailgate is open53Additional tail light activationThe tail lights in the tailgate are deactivated when it is raised. Their functions are taken over by the addtional tail lights in the lower bumper cover. To reliably detect an open tailgate, Rear Lid Alarm Switch F123 and Rear Lid -closed- Sensor G525 are evaluated. F123 has two microswitches in the tailgate lock. G525 is a Hall sensor integrated in the rear lock plate cover. J519 not only evaluates the operating states of both switches, but also the time between the signals generated by both switches. If the time lag is too long between both signals when closing the tailgate, the additional tail lights are not deactivated for safety reasons.Schematic diagram of the circuitRear Lid Alarm Switch F123 Full lock Prelock Terminal 31Vehicle Electrical System Control Module 1 J519602_120Rear Lid -closed- Sensor 1 G525High mounted brake lightThe high mounted brake light is integrated in the rear spoiler. It has a total of 48 LEDs. The component parts of the light cannot be replaced. If a fault occurs, the complete LED module must be replaced after first removing the rear spoiler.602_122License plate lightsThe license plate lights of the Q3 are also LED units. Each light unit has two LEDs. They are activated by J519.602_12354Audi drive selectThe Q3 can be optionally equipped with Audi drive select. The customer can chose between three operating modes: comfort, auto and dynamic. Audi drive select can be set using a button on the instrument panel or through the MMI controls under the CAR menu. The current operating mode is shown on the MMI display.Audi drive selectHandbookAudi drive select: dynamicefficiency comfort auto dynamicCar Systems 22315 D 4 km 142.5 +22.5°C602_135European version shown602_136Controllable systemsThe system is operated using the buttons in the center consoleOperation via CAR menu in Radio Media Center (RMC) or MMIAccelerator/engine Variable characteristicServotronic Variable steering torque602_13755Functional characteristicsEnginecomfort D Engine Power/ torque Load change S auto D S dynamic D Snormal balancednormal balancednormal balancednormal balancednormal sportynormal sportyDrive-independent vehicle systemscomfort Steering auto dynamiccomfortablebalancedsporty56Climate controlEngergy efficiencyThe fully automatic two-zone air conditioning system regulates nominal temperature, air distribution and air flow rate depending on sunlight intensity, interior and exterior temperature. It also has a humidity sensor. A dew point sensor and a windshield temperature sensor are integrated in the base of the mirror to detect impending fogging and to enhance climate comfort through passenger compartment humidity management.Equipment Climate zones Interior filtering Manual air circulation Automatic air circulation Sunlight photosensor Air quality sensor Cabin humidity sensors Seat heating levels Glove compartment cooling system Automatic climate control system Two-zone system Dust and pollen filter without activated charcoal yes yes yes yes yes 3 yesClimatronic Control Module J255In addition to controlling all functions of the climate control system, J255 also houses the controls for